KM Thomas - Access Control and Security Systems

Scan Me forProduct Video•Datasheet•PriceList•InstallInstructions•

Use QR Code Phone App

SECURITY DOOR CONTROLS3580 Willow Lane, Westlake Village, CA 91361-4921 • (805) 494-0622 • Fax: (805) 494-8861

www.sdcsecurity.com • E-mail: [email protected]

P:\INSTALLATION INST\SWITCH KITS\INST-LRVD1R.vsd REV B 12-11 Page 1

Any suggestions or comments to this instruction or

product are welcome. Please contact us through

our website or email [email protected]

LRVD1R

INSTALLATION INSTRUCTIONS

PUSH PAD (REQUEST-TO-EXIT) SWITCH KIT

VON DUPRIN 98/99-33 SERIES

Insert switch assembly into the extrusion with the back of the angle bracket against the inside

wall of the extrusion. Slide the switch assembly toward the device head until it‘s just in front of

the push bar without making contact. Locate and secure REX assembly as illustrated.

Applications

Access Control REX: Provides an authorized request-

to-exit signal to activate an access control REX input,

shunting the access control alarm output.

Magnetic Lock REX: Releases lock for uninhibited

egress when wired in series to lock power, or used to

activate a time delay trigger input to release lock for

egress.

Exit Alarm: May be used to activate an external alarm

horn located adjacent to the opening.

Remote Annunciation: Indicates door use when

connected to a remote annunciator,

RED = N/C

GRN = N/O

WHT = COM

BLK = NOT USED

3AMP @ 125VAC

RESISTIVE

REX SWITCH

ASSEMBLY

TIGHTEN DOWN SCREW

P:\INSTALLATION INST\SWITCH KITS\INST-LRVD2L.vsd REV A 12-11 Page 1




LRVD2L


LATCH STATUS SWITCH KIT

VON DUPRIN 33 SERIES

Attach cable tie to the opposite side of the device with the #10 self-

tapping screw provided. Carefully route cable over device head

making sure NOT to impede the movement of the latch assembly.

Secure cable in the cable tie and carefully route the cable down the

inside wall of the extrusion.

Applications

Access Control REX: Provides an authorized request-

to-exit signal to activate an access control REX input,

shunting the access control alarm output.

Magnetic Lock REX: Releases lock for uninhibited

egress when wired in series to lock power, or used to

activate a time delay trigger input to release lock for

egress.

Exit Alarm: May be used to activate an external alarm

horn located adjacent to the opening.

Remote Annunciation: Indicates door use when

connected to a remote annunciator,

801 Avenida Acaso, Camarillo, Ca. 93012 • (805) 494-0622 •


Attach Latch Switch

assembly to 33 series

device head with the two

#10 x 3/4” screws provided.

LATCH SWITCH

ASSEMBLY

#10 x 3/4” screws

RED = N/C

GRN = N/O

WHT = COM

BLK = NOT USED

3AMP @ 125VAC

RESISTIVE

Tab

#10 self-tapping screw

Screw type cable tie

!"#$%&&%$!'"(!"#$)*+$!'"#(&),--./0

.%&1(1&1+$)!+(&%$+2()1$)%+$!'"(/13!+1(0!$

!"#$%&'()*+$%,+-./$0+1+2)33./$0+4$56"#7$$8$$$9!":;$<5<=">77$$8

???4-*,-',@2)AB4,.1$$8$$C=1+)3D$-'2&),'E-*,-',@2)AB4,.1

!"#$%&''(%)*+"%$+,$-+..(")%$)+$)/*%$*"%),&-)*+"$+,$

0,+1&-)$2,($3(4-+.(5$$64(2%($-+")2-)$&%$)/,+&'/$

+&,$3(7%*)($+,$(.2*4$("'*"((,8%1-%(-&,*)#5-+.$

1&1+$)!+%&(/%$%

9:;<=$8$>??@AB?.!

CD<$EFG HIJ$EKG

6!LDML$6DM<NMO

=2,(P&44#$,(.+Q($)/($D"1$=20$=+Q(,R

D"1$=20R$=+Q(,R$=+Q(,$64&'$2"1

S+&%*"'$=+Q(,5

=+Q(,$64&'

=+Q(,

S+&%*"'$=+Q(,

D"1$=20

D"1$=20$

=+Q(,

6TUNMVL!II!LNWM$NMVLUVXNL=S$JNLVUNMVLKICA??Y<J5Q%1$$$$$CD;$K ?:KAA$$$$62'($A$$

!))2-/$)/($D5I5C5$)+$

)/($S+&%*"'$3*)/$)/($

%&004*(1$%-,(3%5 !))2-/$)/($V),20$!%%#5$

)+$)/($Z+)+,$I*"[5

C(.+Q($.2)(,*24$7()3(("$

)/(%($)3+$/+4(%$)+$P+,.$2$%4+)5

I++%("$%-,(3%$\&%)$

("+&'/$)+$*"%(,)$)/($,+&"1$

0*"$+P$)/($V),20$!%%#5

V),20$!%%(.74#

!"#$%&&%$!'"(!"#$)*+$!'"#(&),--./0

.')1'1/%$!+(2&2+$)!+(&%$+3()2$)%+$!'"(.24!+2(0!$

!"#$%&'()*+$%,+-./$0+1+2)33./$0+4$56"#7$$8$$$9!":;$<5<=">77$$8

???4-*,-',@2)AB4,.1$$8$$C=1+)3D$-'2&),'E-*,-',@2)AB4,.1

!"#$%&''(%)*+"%$+,$-+..(")%$)+$)/*%$*"%),&-)*+"$+,$

0,+1&-)$2,($3(4-+.(5$$64(2%($-+")2-)$&%$)/,+&'/$

+&,$3(7%*)($+,$(.2*4$("'*"((,8%1-%(-&,*)#5-+.$

2&2+$)!+%&(.%$%

9:;<=$8$>??@AB?.!

CD<$EFG HIJ$EKG

6!LDML$6DM<NMO

6PQNMRL!II!LNSM$NMRLQRTNL=U$JNLRQNMRLKICA??<VJ5W%1$$$$$CD;$K ?>KAA$$$$62'($A$$

$C(.+W($)/($X*W($%-,(3%$X,+.$)/($7+))+.$+X$)/($1(W*-($EY$24+"'$)/($-(")(,$2"1$)3+$+"$)/($%*1(%$

2))2-/*"'$)/($/(21G5

$R4*1($)/($7+))+.$/+&%*"'$+XX$+X$)/($6&%/$H2,$.+&")*"'$72%($042)(5

$!))2-/$)/($ICA??<VJ$)+$)/($6&%/$H2,$.+&")*"'$72%($042)($3/(,($%/+3"$3*)/$)/($%-,(3%$0,+W*1(15

6+%*)*+"$)/($%/2X)$-+442,$+"$)/($ICA??<VJ$%+$*)Z%$200,+[*.2)(4#$A@B\$232#$X,+.$)/($6&%/$H2,$%/2X)5$$

L*'/)("$)/($%/2X)$-+442,$*"$042-(5

$R4*1($)/($7+))+.$/+&%*"'$72-]$*"$042-($+W(,$)/($6&%/$H2,$.+&")*"'$72%($042)($2"1$,(K2))2-/$)/($X*W($

%-,(3%5$$L(%)$)/($ICA??<VJ$X+,$0,+0(,$X&"-)*+"$ER/2X)$=+442,$.2#$"((1$211*)*+"24$21^&%).(")$

1(0("1*"'$+"$)/($4("')/$+X$)/($6&%/$H2,$R/2X)G5

$C&"$3*,(%$)/,+&'/$)/($1++,$2"1$2))2-/$)+$0+3(,5$$!))2-/$6&%/$H2,$2%%(.74#$)+$)/($1++,5

A@B\H+))+.

U+&%*"'

ICA??<VJ

6&%/$H2,$

V+&")*"'$H2%(

6&%/$H2,$R/2X)

R/2X)$=+442,

6&%/$H2,

!"#$%&&%$!'"(!"#$)*+$!'"#(&),--+).

+')/!"0)*##1!"(2&2+$)!+(&%$+3()2$)%+$!'"(425!+2(.!$

!"#$%&'()*+$%,+-./$0+1+2)33./$0+4$56"#7$$8$$$9!":;$<5<=">77$$8

???4-*,-',@2)AB4,.1$$8$$C=1+)3D$-'2&),'E-*,-',@2)AB4,.1

!"#$%&''(%)*+"%$+,$-+..(")%$)+$)/*%$*"%),&-)*+"$+,$

0,+1&-)$2,($3(4-+.(5$$64(2%($-+")2-)$&%$)/,+&'/$

+&,$3(7%*)($+,$(.2*4$("'*"((,8%1-%(-&,*)#5-+.$

2&2+$)!+%&(4%$%

9:;<=$8$>??@AB?.!

CD<$EFG HIJ$EKG

6!LDML$6DM<NMO

=2,(P&44#$,(.+Q($)/($D"1$=20$=+Q(,R

D"1$=20R$=+Q(,R$=+Q(,$64&'$2"1

S+&%*"'$=+Q(,5

=+Q(,$64&'

=+Q(,

S+&%*"'$=+Q(,

D"1$=20

D"1$=20$

=+Q(,

6TUNMVL!II!LNWM$NMVLUVXNL=S$JNLVUNMVLKICA??=CJ5Q%1$$$$$CD;$K ?>KAA$$$$62'($A$$

C(.+Q($.2)(,*24$7()3(("$

)/(%($)3+$/+4(%$)+$P+,.$2$%4+)5

I++%("$%-,(3%$Y&%)$

("+&'/$)+$*"%(,)$)/($,+&"1$

0*"$+P$)/($V),20$!%%#5

V),20$!%%(.74#

!))2-/$)/($D5I5C5$)+$

)/($S+&%*"'$3*)/$)/($

%&004*(1$%-,(3%5 !))2-/$)/($V),20$!%%#5$

)+$)/($Z+)+,$I*"[5

INSTALLATION INSTRUCTIONS LR100IDCK

ELECTRIC LATCH RETRACTION DEVICE KIT

P:\INSTALLATION INST\SWITCH KITS\INST-LR100SDC.vsd REV - 08-11 Page 1




Step 1Slide the Electric Latch Retraction

assembly into device and attach

the linkage to the latch retraction

rod.

Step 2Carefully slide the assembly

back out until the linkage JUST

makes contact with the latch

retraction rod. Tighten set

screws.

ELECTRICAL DATA

24VDC @ 500/180mA

RED (+) BLK (-)

PATENT PENDING

NOTE Retro-Fitting Vertical Rod Devices:Before retro-fitting an electric latch assembly into a vertical device, the following must be done

to ensure proper alignment. Disconnect the vertical rods from the device. Install the electric

latch assembly as shown above. Once the ELR is properly installed energize it so that the

push pad is dogged down, by doing so it will allow for proper alignment for the vertical rods.

Finally reconnect the vertical rods to the device and make the proper adjusments.



SET

SCREWS

TIGHTEN SET

SCREWS TO

LOCK DEVICE

IN POSITION

LRCRDIL


LATCH SWITCH KIT

CORBIN/RUSSWIN EXIT DEVICES

P:\INSTALLATION INST\SWITCH KITS\INST-LRCRDIL.vsd REV - 12-11 Page 1




SECURITY DOOR CONTROLS3580 Willow Lane, Westlake Village, CA 91361-4921 • (805) 494-0622 • Fax: (805) 494-8861


Remove Head Cover. Remove and discard existing #8-32 screws.

Install Switch assembly where shown with screws supplied.

Re-attach Head Cover.

WHT – COM ORG – N/C YEL – N/O

LR100VDK-22


ELECTRIC LATCH RETRACTION DEVICE KIT

(VON DUPRIN 22 SERIES)

P:\INSTALLATION INST\SWITCH KIT\INST-LR100VDK-22.vsd REV - 12-11 Page 1




Step 1Remove Von Duprin installed

mechanical dogging assembly.

VON DUPRIN MECHANICAL

DOGGING ASSEMBLY

ELECTRICAL DATA

24VDC @ 500/180mA

RED (+) BLK (-)

PATENT PENDING



NOTE Retro-Fitting Vertical Rod Devices:Before retro-fitting an electric latch assembly into a

vertical device, the following must be done to ensure

proper alignment. Disconnect the vertical rods from

the device head. Install the electric latch assembly

as shown above. Once the ELR is properly installed

energize it so that the push pad is dogged down, by

doing so it will allow for proper alignment for the

vertical rods. Finally reconnect the vertical rods to

the device and make the proper adjusments.

INSTRUCTIONS CONTINUED ON BACK OF PAGE

Disconnect vertical rods from the

Device head

Step 21. Slide the ELR assembly into the device rail.

2. Attach the linkage to the latch retraction rod.

ELR

Assembly CLEVIS

VON DUPRIN LATCH

RETRACTION ROD

LR100 LINKAGE


LR-1VD CONNECTING ROD

FOR USE ON VON DUPRIN DEVICES

LESS DOGGING FEATURE

1. Remove the rail and push pad from the device

2. Drill a 5/32" (.156") diameter hole as shown in

illustration.

3. Insert the connecting rod provided and fasten

in screw

P:\INSTALLATION INST\SWITCH KIT\INST-LR100VDK-22.vsd REV - 12-11 Page 2

When retrofitting to existing vertical rod

devices, adjustment of the rods are required

for proper assembly of the LR100VDK Kit.

Please see the SDC website

(www.sdcsecurity.com) for installation tips

and photographs of installing.

.250

Push

Pad

Rail

Device

LR-1VD

Connecting Rod

#6-32 x 3/8

Step 3Carefully slide the ELR assembly

back out until the linkage JUST

makes contact with the latch

retraction rod. Fasten down the

2 supplied set screws to secure

the assembly to the device.

BACK ELR OUT

UNTIL LINKAGE

JUST MAKES

CONTACT HERE

TIGHTEN DOWN

SET SCREWS TO

LOCK DEVICE IN

POSITION

Documents

KM Thomas - Access Control and Security Systems