KIT12XS6EVM Evaluation Board - NXP Semiconductors · 2019. 7. 17. · Getting Started KT12XS6EVMUG Rev. 1.0 4 Freescale Semiconductor, Inc. 2Getting Started 2.1 Kit Contents/Packing

Freescale Semiconductor, Inc.User’s Guide

© Freescale Semiconductor, Inc., 2015. All rights reserved.

Document Number: KT12XS6EVMUGRev. 1.0, 10/2015

KIT12XS6EVM Evaluation Board

Figure 1. KIT12XS6EVM

KT12XS6EVMUG Rev. 1.02 Freescale Semiconductor, Inc.

Contents1 Important Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Getting Started. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Understanding the Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Getting to Know the Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Accessory KITLIGHTEVB Load Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 Installing the Software and Setting up the Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168 Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199 Board Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2010 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2211 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Important Notice

KT12XS6EVMUG Rev. 1.0 Freescale Semiconductor, Inc. 3

1 Important NoticeFreescale provides the enclosed product(s) under the following conditions:

This evaluation kit is intended for use of ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES ONLY. It is provided as a sample IC pre-soldered to a printed circuit board to make it easier to access inputs, outputs, and supply terminals. This evaluation kit may be used with any development system or other source of I/O signals by simply connecting it to the host MCU or computer board via off-the-shelf cables. Final device in an application will be heavily dependent on proper printed circuit board layout and heat sinking design as well as attention to supply filtering, transient suppression, and I/O signal quality.

The goods provided may not be complete in terms of required design, marketing, and or manufacturing related protective considerations, including product safety measures typically found in the end product incorporating the goods. Due to the open construction of the product, it is the user's responsibility to take any and all appropriate precautions with regard to electrostatic discharge. In order to minimize risks associated with the customers applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. For any safety concerns, contact Freescale sales and technical support services.

Should this evaluation kit not meet the specifications indicated in the kit, it may be returned within 30 days from the date of delivery and will be replaced by a new kit.

Freescale reserves the right to make changes without further notice to any products herein. Freescale makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typical”, must be validated for each customer application by customer’s technical experts.

Freescale does not convey any license under its patent rights nor the rights of others. Freescale products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale product could create a situation where personal injury or death may occur.

Should the Buyer purchase or use Freescale products for any such unintended or unauthorized application, the Buyer shall indemnify and hold Freescale and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale was negligent regarding the design or manufacture of the part. Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. © Freescale Semiconductor, Inc. 2015

Getting Started


2Getting Started

2.1 Kit Contents/Packing ListThe KIT12XS6EVM contents include:

• Assembled and tested evaluation board in anti-static bag• USB cable• Warranty card

2.2 Jump StartFreescale’s analog product development boards help to easily evaluate Freescale products. These tools support analog mixed signal and power solutions including monolithic ICs using proven high-volume SMARTMOS mixed signal technology, and system-in-package devices utilizing power, SMARTMOS and MCU dies. Freescale products enable longer battery life, smaller form factor, component count reduction, ease of design, lower system cost and improved performance in powering state of the art systems.

• Go to www.freescale.com/KIT12XS6EVM• Look for

• Download documents, software and other informationOnce the files are downloaded, review the user guide in the bundle. The user guide includes setup instructions, BOM and schematics. Jump start bundles are available on each tool summary page with the most relevant and current information. The information includes everything needed for design.

2.3 Required Equipment and Software To use this kit, you need:

• Power supply 30 V with current up to 30 A for full performance• Typical loads: LED or incandescent bulbs from 5.0 W to 60 W• (Optional) KITLIGHTEVB load module• (Optional) P&E USB BDM Multi-link Cable:

http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=USBMULTILINKBDM

2.4 System RequirementsThe kit requires the following to function properly with the software:

• USB-enabled PC with Windows® XP or higher

Jump Start Your Design

http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=USBMULTILINKBDMhttp://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=USBMULTILINKBDMwww.freescale.com/KIT12XS6EVMwww.freescale.com/KIT12XS6EVM

Understanding the Board


3 Understanding the BoardThis board is a full safety system that can drive the exterior lighting of a car. It consists of:

• Two MC07XS6517 (Triple 7 m and Dual 17 m high-side switches) for front side of the car• 2 x MC17XS6500 (Penta 17 m high-side switches) for rear side of the car• MC33903 System basis chip for microcontroller supply, safety behavior and communication• HCS12G128 for CAN, LIN and SPI control

This system is provided with GUI (and optional KITLIGHTEVB) to start the board and get a quick overview of the device functions.You can check the following demonstration video for a global presentation of the system http://www.freescale.com/webapp/video_vault/videoSummary.sp?code=FTF2014_LRDFEXTREMESW_VID.

The KIT12XS6EVM contains 20 power outputs for current ranges up to 22 A DC. Microcontroller supply, safety behavior and communication with the system is managed by the embedded System Basis Chip MC33903.

3.1 Block DiagramThe high level system block diagram in Figure 2 outlines the way Freescale standard products are used to implement a full automotive lighting system.

Figure 2. Block Diagram

Bluetooth(optional

MCU

System Basis Chip

(SBC

High-side Switches

USBUART

(optional)

High-side Switches

USB

CAN

LIN

VBAT

High-side Switches

High-side Switches

.

.

.High BeamLow BeamBrakeFogStopFlasherInterior..Incandescent HID ballastXenonLED modules..

http://www.freescale.com/webapp/video_vault/videoSummary.sp?code=FTF2014_LRDFEXTREMESW_VID

Understanding the Board


3.1.1 Device FeaturesThis board features the following Freescale products:

Table 1. Device Features

Device Description Features

S12G128 16-bit Microcontroller

• S12 CPU core, 25 MHz bus• Up to 240 KB on-chip flash with ECC• Up to 4.0 KB EEPROM with ECC• Up to 11 KB on-chip SRAM• Up to one multi-scalable controller area network (MSCAN) module• Supporting CAN protocol 2.0 A/B• Up to three serial communication interface (SCI) modules• Supporting LIN communications• Up to three serial peripheral interface (SPI) modules• Precision fixed voltage reference for analog-to-digital conversion (ADC)• 1 MHz internal oscillator• On-chip voltage regulator for input supply and internal voltages

MC33903System Basis Chip Gen2 with High-speed CAN and LIN

• Voltage regulator for MCU, 5.0 V or 3.3 V, • Voltage, current and temperature protection• Extremely low quiescent current in low power modes• Fully-protected embedded 5.0 V regulator for the CAN driver• Multiple undervoltage detections to address various MCU specifications and system operation

modes (i.e. cranking)• Auxiliary 5.0 V or 3.3 V SPI configurable regulator, for additional ICs, with overcurrent detection and

undervoltage protection• Advanced SPI, MCU, ECU power supply and critical pins diagnostics and monitoring.• Multiple wake-up sources in low-power modes: CAN or LIN bus, I/O transition, automatic timer, SPI

message and VDD over-current detection. • ISO11898-5 high-speed CAN interface compatibility for baud rates of 40 kb/s to 1.0 Mb/s

MC07XS6517/MC17XS6500 Smart High-side Switches

• Normal operating range from 7.0 V to 18 V, extended range: 6.0 V to 28 V.• 5.0 V compatible 16-bit SPI port for device control, configuration and diagnostics at rates up to

5MHz• Individually programmable external PWM clock signals (switching frequency prescaler, duty cycle,

slew rate, phase shift)• Overcurrent, short-circuit and overtemperature protection• Accurate temperature, voltage and current sensing with high precision (from 27.5 mA to 22 A) and

synchronization pin• Open load detection in ON and OFF state or in LED mode• Configurable profile to fit with incandescent bulbs, LED or HID ballast (current sense ratio or over-

current profiles adjusted)• Watchdog and Limp Home mode• External smart power switch control

Getting to Know the Hardware


4 Getting to Know the Hardware

4.1 Board OverviewThe KIT12XS6EVM is an easy-to-use circuit board allowing the user to exercise all the functions of the MC07XS6517 and MC17XS6500 smart high-side switches. A PC links to the EVM through an onboard USB port with a Serial UART interface. A Graphical User Interface (GUI), included with the kit, allows you to communicate with the EVM for a quick overview of the device functions.This KIT12XS6EVM comes with microcode already loaded in the S12G128’s on-board flash memory. However, users who are developing a customized approach can download their own microcode to the device using the Background Debug Mode (BDM) connector.

4.2 Board FeaturesThe key features of KIT12XS6EVM are as follows:

• 20 protected power high-side switches with low RDS(on) (14 x 17 m + 6 x 7 m) • Normal operating range from 7.0 V to 18 V, extended range: 6.0 V to 28 V• Background Debug Mode (BDM) connector for downloading microcode to the S12G128 on-chip flash memory• CAN and LIN bus connectors• Bluetooth connector with LDO voltage regulator• USB port with Serial UART support• Individually programmable external PWM clock signals (switching frequency prescaler, duty cycle, slew rate, phase shift)• Overcurrent, short-circuit and overtemperature protection• Accurate temperature, voltage, and current sensing with high precision (from 27.5 mA to 22 A)• Open load detection in ON and OFF state or when the load is LEDs• Configurable profile to fit with incandescent bulbs, LED or HID ballast (current sense ratio or overcurrent profiles adjusted)



4.3 Board Description Figure 3 describes the main blocks of the KIT12XS6EVM.

Figure 3. Board Description

Table 2. Board Description

Name Description

2 x MC07XS6517, 2 x MC17XS6500 eXtreme switches

Four 5-channel fully protected high power high-side switches. Communication with microcontroller through SPI daisy chain. Power outputs routed to edges connectors

16-bit MCU S12G128 MCU for safety and device controlSBC MC33903 System Basis Chip with high speed CAN and LIN communication, supplies the MCU, safety managementBDM connector Allows to flash the S12G MCUCAN and LIN connectors Allows to drive the board through CAN or LIN protocolsUSB Connector Mini-USB connector for GUI applicationBluetooth Connector (optional) Plug for an external Bluetooth dongle (reference RN42-I/RM)

Mini USB

MC17XS6500

MC33903

CAN Connector

LIN Connector

MC07XS6517

MC07XS6517

Connector for

BDMMC17XS6500

Bluetooth interface

S12G128



4.4 LED DisplayThe following LEDs are provided as visual output devices for the KIT12XS6EVM:

Figure 4. LED Locations

Table 3. LEDs

Label Description

D4 Indicates the presence of the 5.0 V VDD supply (LED color: Red)

D6 Indicates the status of the UART_RX communication (LED is blinking and the color is orange when communication is OK

D7 Indicates the status of the UART_TX communication (LED is blinking and the color is green when communication is OK

Red LED

Orange LED

Green LED



4.5 ConnectorsThere are input/output connectors, which provide the following signals:

Figure 5. LED Locations

Table 4. Connector List

JP2 Top Connector Device #4 JP3 Top Connector Device #2 JP4 Top Connector Device #3 JP5 Top Connector Device #1

Position Signal Name DescriptionSignal Name Description

Signal Name Description

Signal Name Description

1 OUT1_4 Output1 Device#4 OUT1_2 Output1 Device#2 OUT1_3 Output1 Device#3 OUT1_1 Output1 Device#12 OUT2_4 Output2 Device#4 OUT2_2 Output2 Device#2 OUT2_3 Output2 Device#3 OUT2_1 Output2 Device#13 OUT3_4 Output3 Device#4 OUT3_2 Output3 Device#2 OUT3_3 Output3 Device#3 OUT3_1 Output3 Device#14 OUT4_4 Output4 Device#4 OUT3_2 Output3 Device#2 OUT4_3 Output3 Device#3 OUT3_1 Output3 Device#15 OUT5_4 Output5 Device#4 OUT4_2 Output4 Device#2 OUT5_3 Output4 Device#3 OUT4_1 Output4 Device#16 VBAT3 Supply Voltage OUT4_2 Output4 Device#2 VBAT3 Supply Voltage OUT4_1 Output4 Device#17 VBAT3 Supply Voltage OUT5_2 Output5 Device#2 VBAT1 Supply Voltage OUT5_1 Output5 Device#18 GND Ground reference OUT5_2 Output5 Device#2 GND Ground reference OUT5_1 Output5 Device#19 GND Ground reference VBAT2 Supply Voltage GND Ground reference VBAT2 Supply Voltage

10 GND Ground reference GND Ground reference GND Ground reference VBAT2 Supply Voltage

JP2

JP5

JP3JP4



4.6 Test Point DefinitionsThe following test-point jumpers provide access to signals on the KIT12XS6EVM:

4.7 USB ConnectorA Mini-USB connector is available for communication with computer through UART protocol. Both polarities of the USB connector are connected to the FT232RQ chip to emulate Serial Communication Interface (SCI) communication. The RXD/TXD lines are directly connected to the microcontroller.

The USB connector links to the computer through a COM port in order to communicate with the GUI (the one provided with this KIT12XS6EVM, or a custom one).

Table 5. Test Points

Schematic Label Name Description

TP1, TP3, TP7, TP9, TP11 GND Supply VoltageTP2 V_CAN 5.0 V CAN VoltageTP4 VBAT1 Supply Voltage 1TP5 VDD 5.0 V VDD VoltageTP6 VBAT3 Supply Voltage 3TP8 VBAT2 Supply Voltage 2TP10 3V3 3V3 reference voltage for Bluetooth (optional)

Accessory KITLIGHTEVB Load Module


5 Accessory KITLIGHTEVB Load ModuleFreescale’s KITLIGHTEVB provides an ideal load module for use with the KIT12XS6EVM. The KITLIGHTEVB serves as a platform for preliminary evaluation of the board and acts as a starting point for any software development on the KIT12XS6EVM.The KITLIGHTEVB provides various types of loads that address the 20 outputs available on the KIT12XS6EVM. Those outputs are:

• Three 12 V-55/60 W H4 bulbs for high beam/low beam• Two 12 V 21 W bulbs for parking lights, fog lights, brake lights and flashers• Four 12 V 5/21 W bulbs for parking lights, fog lights, brake lights, flashers, parking lights and low beam• Four 12V LED loads for parking lights, fog lights and brake lights

The KIT12XS6EVM mounts to the KITLIGHTEVB and uses the KITLIGHTEVB’s high power connectors for VPWR and all outputs.

Figure 6. KITLIGHTEVB Load Module

6 Installing the Software and Setting up the Hardware

6.1 Installing the GUI on your Computer1. Download the installation file “Labview_GUI_install.zip” from www.freescale.com/KIT12XS6EVM. Unzip the file and then

double-click the setup.exe file.

2. Select your destination directory and click “Next”. The License Agreement box opens. Click to accept the terms of the agreement.

3. Click the Next button to start the installation program. The Installation Wizard prompts you for further actions.

4. Once the installation completes, restart your machine.

5. Launch the GUI by clicking on the “Gen4 Lighting” icon (located on your desktop or in your Start menu, depending on which option you selected during the installation.)

6. Connect USB cable and wait until the driver is installed: FT232R USB UART.

www.freescale.com/KIT12XS6EVMwww.freescale.com/KIT12XS6EVM

Installing the Software and Setting up the Hardware


7. Go into the device manager of your computer and note the corresponding COM port associated with FT232R USB UART.

8. On the GUI (box with label 6 on the below picture), select the corresponding COM port noted in the previous step.

9. If the corresponding COM port is not displayed in the box, please install following VISA driver: http://compass.freescale.net/livelink/livelink/232759628/NI_VISA_driver.zip?func=doc.Fetch&nodeid=232759628. After unzipping the file, double click on NIVISAruntime.msi to update the driver (and/or devsupport64 if x64)

6.2 Describing the GUI InterfaceThe Gen4 Lighting GUI allows you to:

• Display the real time Voltage on the VPWR pin of each device

• Display the real time Temperature of each device

• Display the output current for a selected channel on the oscilloscope view

• Independently turn on the 5 outputs of each of the four devices and change the duty cycle.

• Continuously refresh each device register (quick status + selectable register)

• Send specific SPI commands issued from specification

• Reset devices and the GUI

Figure 7. GUI Interface

�

��

�

� �

�

compass.freescale.net/livelink/livelink/232759628/NI_VISA_driver.zip?func=doccompass.freescale.net/livelink/livelink/232759628/NI_VISA_driver.zip?func=doc.Fetch&nodeid=232759628



The GUI provides a graphical view of register status and operating parameters for the four 12XS6 switches controlled by the MCU inside the KIT12XS6EVM. The GUI refers to the 12XS6’s as Device number 1—4 (see Table 6 to identify the device type and board connector associated with each Device number.) The five channels on each device are also color coded from dark blue (channel1), red (channel 2), green (channel 3), light blue (channel 4), and yellow (channel 5.)

Quick Status Fault Reporting - Displays the Quick Status SPI Output (SPI MISO) register flags for each of the four devices. The display is continuously refreshed while the GUI is turned on.

SPI Read Register Selection - Allows you to select a device and specify which SPI Output register to display.

Register Status - Displays the status of the selected device register (Item 2.) The display refreshes each time the device register is selected.

PWM Output Control - Allows you to view and modify the duty cycle for a device/channel combination. To select a device/channel, set the ON/OFF button for that combination. The duty cycle displays as a colored bar in the box below the device/channel name and as a percentage in the box next to the button. To alter the duty cycle, click on the bar and drag it horizontally. The percentage value appears immediately above your cursor.

RST E-switch - Resets all four devices and initializes the GUI to its start-up state.

Communication Port Selection - Displays the PC COM port the GUI is communicating through. Clicking on the button in the box allows you to change the port.

GUI OFF - Clicking on the button stops GUI communication with the KIT12XS6EVM board.

Supply Voltage/Device Temperature Display - Allows you to select a device and display the supply voltage and temperature of that device. Over/undervoltage and over/undertemperature indicators turn on when the device is operating outside its voltage or temperature range. The information updates in real-time. In this implementation, when VPWR voltage is less than 9.0 V, "UV" reports "1" and when VPWR is greater than 16 V,"OV" reports "1".

Manual SPI Control - Allows you to enter SPI SI and SO commands as Hexadecimal values and to send the commands to a selected device.

Oscilloscope View - Allows you to select a device/channel combination and monitor its output current in real time. Controls at the lower right allow you to alter how the plot is displayed.To select a device/channel combination for monitoring:

1. Go to the PWM Output Control panel and turn on the device/channel you wish to monitor (for instance, D3PWM4.)

2. In the oscilloscope view, click the tab corresponding to the device you selected (in this example, 17XS6500 #3.)

3. In the panel to the right of the plot screen, click on the output channel you selected (in this example, OUT4.)

Do not select more than one device/channel combination at a time.

Table 6. Device Identification

Device # Device Name Board Connector1 MC07XS6517EK JP52 MC07XS6517EK JP33 MC17XS6500EK JP44 MC17XS6500EK JP2



6.3 Configuring the HardwareFigure 8 illustrates the hardware configuration when used with the KITLIGHTEVB Load Module.

Figure 8. Board Setup

6.3.1 Step-by-step Instructions for Setting up the HardwareThe KIT12XS6EVM is designed for use with Freescale’s KITLIGHTEVB evaluation module. Alternatively, you may choose to provide your own hardware to use in conjunction with the KIT12XS6EVM. The following instructions describe how to set up the KIT12XS6EVM when a KITLIGHTEVB is used as a load module. If you are using a different type of load module, consult the schematic (see Section 7) and the board descriptions (see Section 4) to determine how to connect to the KIT12XS6EVM.

1. Mount the KIT12XS6EVM board to the KITLIGHTEVB load module.

2. Insert the USB Mini-B plug into the USB port on the KIT12XS6EVM board.

3. Connect the other end of the USB cable to a PC that has the Gen4 Lighting GUI installed (See Section 6.1)

4. Connect the +12 V DC power supply to the power and ground connectors on the KITLIGHTEVB board. Turn on the power supply

5. Turn on the KITLIGHTEVB module by pushing the ON/OFF switch (located between the power and ground connectors.)

6. Launch the GUI by clicking on the “Gen4 Lighting” icon (located either on your desktop or in the Program folder, depending on which option you selected during the GUI installation.)

7. If the correct COM port is not selected by default on the box under Freescale logo, associate the correct COM port as described in Section 6.1. Then stop and restart the GUI (red circle and black arrow on the top left of the GUI.)

KITLIGHTEV� Load Module

KIT12XS6EVM

Schematic


7 Schematic

Figure 9. Schematic, Part 1

Bluetooth

TXD

RXD

BKGD

RESET_B

VDD

RESE

T_R_

BRE

SET_

BBK

GD

BOSS

_RST

_B

SBC_

RST_

B

IRQ

_B

SBC_

MIS

OSB

C_M

OSI

SBC_

SCLK

SBC_

SS_B

RXD

CTX

DC

XTAL

EXTA

L

RXD

TXD

RXL1

TXL1

BOSS

_MIS

OBO

SS_M

OSI

BOSS

_SCL

KBO

SS_S

S_B

PAD

0

PAD

2M

UX

CSN

S

PWM

4CL

K

SAFE

_B

SAFE

1

SYN

C_B

USB

D_N

USB

_N

USB

D_P

USB_SHIELD

VBU

S

USB

_P

VBU

S_FF

B5V

_VBU

S

TXD

RXD

3V3

VDD

VDD

VDD

VDD

VDD

5V_V

BUS

3V3O

UT

5V_V

BUS

3V3

VDD

3V3

3V3

VDD

VDD

CLK

(4)

CSN

S(4

)

MU

X(3

)

BOSS

_SS_

B(4

)BO

SS_S

CLK

(4)

BOSS

_MO

SI(4

)

TXL1

(3)

RXL1

(3)

TXD

C(3

)RX

DC

(3)

SBC

_SS_

B(3

)SB

C_S

CLK

(3)

SBC

_MIS

O(3

)

IRQ

_B(3

)

SBC

_RST

_B(3

)

BOSS

_RST

_B(4

)

SAFE

_B(3

)

SAFE

1(4

)

SYN

C_B

(4)

SBC

_MO

SI(3

)

BOSS

_MIS

O(4

)

R28

10.0

K

U4

S9S1

2G12

8F0C

LF

RESE

T1

VDDXR2

EXTA

L/PE

04

VSSX3

XTA

L/PE

16

TEST

7

PJ0/

KWJ0

/PW

M6/

MIS

O1

8

PJ1/

KWJ1

/IOC

6/M

OSI

19

PJ2/

KWJ2

/IOC

7/SC

K110

PJ3/

KWJ3

/PW

M7/

SS1

11

BKG

D/M

OD

C12

API

_EXT

CLK

/ETR

IG0/

PWM

0/KW

P0/P

P013

ECLK

X2/E

TRIG

1/PW

M1/

KWP1

/PP1

14ET

RIG

2/PW

M2/

KWP2

/PP2

15ET

RIG

3/PW

M3/

KWP3

/PP3

16PW

M4/

KWP4

/PP4

17PW

M5/

KWP5

/PP5

18

PT5/

IOC

519

PT4/

IOC

420

PT3/

IOC

321

PT2/

IOC

222

PT1/

IOC

1/IR

Q23

PT0/

IOC

0/XI

RQ24

AN

0/KW

AD

0/PA

D0

25

AN

8/KW

AD

8/PA

D8

26

AN

1/KW

AD

1/PA

D1

27

AN

9/KW

AD

9/PA

D9

28

AN

2/KW

AD

2/PA

D2

29

AN

10/K

WA

D10

/PA

D10

30

AN

3/KW

AD

3/PA

D3

31

AN

11/K

WA

D11

/PA

D11

32

AN

4/KW

AD

4/PA

D4

33A

N5/

KWA

D5/

PAD

534

AN

6/KW

AD

6/PA

D6

35A

N7/

KWA

D7/

PAD

736

VDDA/VRH37

VSSA38

RXD

0/PS

039

TXD

0/PS

140

RXD

1/PS

241

TXD

1/PS

342

MIS

O0/

PS4

43M

OSI

0/PS

544

SCK0

/PS6

45A

PI_E

XTC

LK/E

CLK

/SS0

/PS7

46

VSS5

PM0/

RXD

2/RX

CA

N47

PM1/

TXD

2/TX

CA

N48

R1 4.7K

C31

0.1u

F

R27

560

C53

4.7u

F

R14

5.0K

L1 60O

HM

12

R11

0

+ -

V+ GN

DU7A

LM35

8MX/

NO

PB

3 21

8 4

TP5

TP3

U8

FT23

2RQ

GND14

AGND24

RI#

3D

CD

#7

DSR

#6

DTR

#31

3V3O

UT

16

VCC

IO1

OSC

I27

RESE

T#18

NC

623

OSC

O28

CBU

S49

CBU

S311

CBU

S121

CBU

S022

CBU

S210

NC

529

NC

425

NC

313

NC

212

NC

15

USB

DP

14

USB

DM

15

VCC

19

GND420

GND217

TEST26

CTS

#8

RTS#

32RX

D2

TXD

30

EP33

TP11

TP10

R23

1.00

k

R13

10.0

K

C47

0.01

UF

TPS7

333Q

D

U9

GND1

EN2

IN1

3

IN2

4

OU

T15

OU

T26

SEN

SE7

RESE

T8

+ -U7B

LM35

8MX/

NO

PB

5 67

R31

10.0

K

R34

0

L2 330

OH

M

12

D7

LED

_GRE

EN

A CC11

8.0P

F

R32

10.0

K

C48

0.1U

F

R81.

00k

8MH

zY1

1 2

C18

0.1u

F

C10

0.01

uF

C78.

0PF

R33

0

J4 VBU

S1

D-

2

D+

3

ID4

GN

D5

SHELL16

SHELL27

SHELL38

SHELL49

R29

560

+C46

4.7U

F

C35

0.1u

F

R24

1.00

k

R30

10.0

K

C52

10uF

R10

10.0

K

C17

0.1u

F

R9 1M

J2 HD

R 2X

3

12

34 6

5

C13

0.01

uF

R26

10.0

K

F10.

5A1

2

R22

5.0K

C54

0.1u

F

JP1

HD

R_1X

6

1 2 3 4 5 6

D6

LED

_ORA

NG

E

A C

Mic

roco

ntro

ller

3.3V

LD

O fo

r Blu

etoo

th H

eade

r

US

B to

Ser

ial U

AR

T In

terfa

ce

BD

M D

ebug

Inte

rface

Schematic


Figure 10. Evaluation Board Schematic, Part 2

1uF1uF

F_ON1

VSENSE

VSENSE

TXL1RXL1

F_ON2

RXDCTXDC

V_CAN

MUX

SBC_SCLK

SBC_SS_B

SBC_RST_B

VREG_VE

VREG_VB

SBC_MOSI

SBC_MISO

CANHCANL XCVR_CANL

XCVR_CANH

CAN_SPLIT

LIN-T1

LIN1

VSUP

SAFE_B

DBG

IRQ_B

VBAT1

V_CAN

VDD

V_CAN

VBAT1

VDD

RXL1 (2)

RXDC (2)

TXL1 (2)

TXDC (2)

SBC_SCLK (2)

SBC_SS_B (2)

MUX (2)

IRQ_B (2)

SBC_RST_B (2)

F_ON2(4)

F_ON1(4)

SAFE_B(2)

SBC_MOSI (2)

SBC_MISO (2)

R17 1.00k

C56TP1

D21N4148WS

AC

TP7

C3

0.1uF

C23

100pF

R15 1.00k

U2

MCZ33903CD5EK

MUX-OUT11

IO-012

VSU

P2

DBG13

RXD31

VE

32

VB

1

SAFE5

RXD-L216

TXD-L120

GN

D1

15

RXD-L121

CANH7

SPLIT10

CANL8

LIN-T1/I/O-24

LIN217

MISO28

VSENSE22

RST23

SCLK26

CS25

MOSI27

INT24

TXD-L214

5V-CAN6

VDD29

TXD30

GN

D2

18

LIN119

GN

D_C

AN

9

EX_P

AD

33

LIN-T2/I/O-33

C57

J1

HDR_1X4

1234

D4RED LED

AC

D11PESD1LIN

12

C22

0.1uF

L3B82789C0513N002

13

24

D9

MMSZ8V2T1GA C

R21.00k

R19 1.00k

R1610.0K

R71.00k

R460.4

TP2

D3

MM

SZ52

31BT

1GA

C

D1

MMSZ5253BT1G

A C

D8RED LED

AC

D5

BZT52C20T-7

AC

C55

10uF

C25

100pF

R560.4

D10

PESD1CAN

1

23

TP4

C4

0.1uF

C1

10uF

C581000PF

R310.0K

C6

4700PF

EB

C

Q1

BCP52-161

32 4

J3

HDR_1X2

12

C24

2.2uF

R6 1.00k

R20 47K

SBC with CAN High Speed and LIN Interface

CAN

LIN

Schematic


Figure 11. Schematic, Part 3

BOSS

_RST

_BBO

SS_S

S_B

CSN

SSY

NC_

B

BOSS

1_O

UT4

BOSS

1_O

UT5

BOSS

1_O

UT2

BOSS

1_O

UT1

BOSS

1_O

UT3

BOSS

_RST

_BBO

SS_S

S_B

SAFE

1

F_O

N1

F_O

N2

BOSS

2_O

UT4

BOSS

2_O

UT5

BOSS

2_O

UT3

BOSS

_RST

_BBO

SS_S

S_B

CLK

BOSS

_SCL

KA2

_MIS

O

A3_M

ISO

SAFE

1

F_O

N1

F_O

N2

CSN

SSY

NC_

B

BOSS

3_O

UT4

BOSS

3_O

UT5

BOSS

3_O

UT3

BOSS

4_O

UT4

BOSS

4_O

UT5

BOSS

4_O

UT3

BOSS

_RST

_BBO

SS_S

S_B

CLK

A3_M

ISO

BOSS

_SCL

K

BOSS

_MIS

O

SAFE

1

F_O

N2

F_O

N1

CSN

SSY

NC_

B

BOSS

_SCL

KBO

SS_M

OSI

A1_

MIS

O

CLK

BOSS

_SCL

KA1

_MIS

OA2

_MIS

O

CSN

SSY

NC_

B

BOSS

2_O

UT2

BOSS

2_O

UT1

BOSS

3_O

UT2

BOSS

3_O

UT1

BOSS

4_O

UT2

BOSS

4_O

UT1

VDD

VBAT

2

VBAT

2

VDD

VBAT

2

VBAT

2

VDD

VBAT

3

VBAT

3

VDD

VBAT

3

VBAT

3

VBAT

2VB

AT2

VBAT

3VB

AT1

VBAT

3

BOSS

_RST

_B(2

,4)

BOSS

_RST

_B(2

,4)

BOSS

_SS_

B(2

)BO

SS_S

CLK

(2)

BOSS

_MO

SI(2

)

F_O

N1

(3)

F_O

N2

(3)

BOSS

_MIS

O(2

)

CLK

(2)

SAFE

1(2

)

CSN

S(2

)SY

NC

_B(2

)

C36 0.022uFC49 0.022uF

C34 0.022uF

C12

0.1u

F

C44

0.1u

F

C26 0.022uF

JP3

HD

R_1X

10

1 2 3 4 5 6 7 8 9 10

U1

MC1

7XS6

500E

K

CS

3

SCLK

4

SI5

SO7

OU

T68

VBAT33

IN2

28

RST

2

OU

T4_3

14

LIM

P31

CLK

32

NC

216

OU

T5_1

17

OU

T5_2

18

OU

T3_1

19

OU

T3_2

20

OU

T3_3

21

VCC6

GND19

OU

T4_2

13O

UT4

_112

OU

T2_2

11O

UT2

_110

IN4

30IN

329

CP

1

OU

T1_1

22

OU

T1_2

23

GND224

CSN

S25

CSN

S_SY

NC

26

NC

115

IN1

27

C45 0.022uF

JP2

HD

R_1X

10

1 2 3 4 5 6 7 8 9 10

C37 0.022uFC20 0.022uF

C43

0.1u

F

C51 0.022uF

C27

0.1u

F

TP6

C21 0.022uF

C39 0.022uF

C15

0.1u

F

C50 0.022uF

C19 0.022uF

TP9

C41

0.1u

F

JP4

HD

R_1X

10

1 2 3 4 5 6 7 8 9 10

R18

100

C2 0.1

uF

C5 0.1

uF

C14

0.1u

F

C8 0.022uF

C16

0.1u

F

U5

MC1

7XS6

500E

K

CS

3

SCLK

4

SI5

SO7

OU

T68

VBAT33

IN2

28

RST

2

OU

T4_3

14

LIM

P31

CLK

32

NC

216

OU

T5_1

17

OU

T5_2

18

OU

T3_1

19

OU

T3_2

20

OU

T3_3

21

VCC6

GND19

OU

T4_2

13O

UT4

_112

OU

T2_2

11O

UT2

_110

IN4

30IN

329

CP

1

OU

T1_1

22

OU

T1_2

23

GND224

CSN

S25

CSN

S_SY

NC

26

NC

115

IN1

27

C33 0.022uF

C42 0.022uF

C29 0.022uF

U3

MC0

7XS6

517E

K

CP

3

RST

4

CS

5

SCLK

6

SI7

VCC8

SO9

OU

T2_1

12

OU

T610

GND111

NC

11

OU

T5_1

037

OU

T3_1

39

OU

T1_1

42

OU

T1_2

43

OU

T5_6

33

OU

T2_2

13

OU

T4_1

14

OU

T4_2

15

OU

T4_3

16

NC

318

NC

419

NC

520

NC

621

NC

722

NC

823

CLK

52LI

MP

51

IN4

50IN

349

IN2

48IN

147

CSN

S_SY

NC

46C

SNS

45

GND244

VBAT55

NC

924

NC

1025

NC

1126

NC

1227

OU

T5_1

28

OU

T5_2

29

OU

T5_3

30

OU

T5_4

31

OU

T5_5

32

NC

1353

NC

22

OU

T5_9

36O

UT5

_835

OU

T3_3

41O

UT3

_240

OU

T5_7

34

NC

1454

JP5

HD

R_1X

10

1 2 3 4 5 6 7 8 9 10

U6

MC0

7XS6

517E

K

CP

3

RST

4

CS

5

SCLK

6

SI7

VCC8

SO9

OU

T2_1

12

OU

T610

GND111

NC

11

OU

T5_1

037

OU

T3_1

39

OU

T1_1

42

OU

T1_2

43

OU

T5_6

33

OU

T2_2

13

OU

T4_1

14

OU

T4_2

15

OU

T4_3

16

NC

318

NC

419

NC

520

NC

621

NC

722

NC

823

CLK

52LI

MP

51

IN4

50IN

349

IN2

48IN

147

CSN

S_SY

NC

46C

SNS

45

GND244

VBAT55

NC

924

NC

1025

NC

1126

NC

1227

OU

T5_1

28

OU

T5_2

29

OU

T5_3

30

OU

T5_4

31

OU

T5_5

32

NC

1353

NC

22

OU

T5_9

36O

UT5

_835

OU

T3_3

41O

UT3

_240

OU

T5_7

34

NC

1454

C32 0.022uF

C38 0.022uF

R21

100

C30 0.022uF

R25

100

TP8

R12

100

C40

0.1u

F

C28

0.1u

F

C9 0.022uF

Sw

itch-

1S

witc

h-2

Sw

itch-

3S

witc

h-4

12X

S6-

1#12

XS

6-2#

12X

S6-

3#12

XS

6-4#

Board Layout


8 Board Layout

8.1 Silkscreen

Figure 12. KIT12XF6EVM Silkscreen

Board Bill of Materials


9 Board Bill of MaterialsTable 7. Bill of Materials(1)

Item Qty Schematic label VALUE DESCRIPTION Part Number

Freescale components1 2 U1,U5 IC SW 17 m PENTA HS SOIC32 MC17XS6500EK

2 1 U2 IC XCVR CAN DUAL LIN 5.0 V 5.5-28 V AEC-Q100 SOIC32MCZ33903CD5EK

3 2 U3,U6 IC SW TRIPLE 7 m AND DUAL 17 m HS 4.5-5.5 V SOIC54MC07XS6517EK

4 1 U4 IC MCU 16 BIT 128K FLASH 8K RAM 25 MHZ 3.13-5.5 V LQFP48S9S12G128F0CLF

Active components5 1 U7 IC LIN OPAMP DUAL 3-32 V SOIC8 LM358MX/NOPB6 1 U8 IC XCVR USB TO UART CTLR 3.3-5.25 V QFN32 FT232RQ7 1 U9 IC VREG LDO 3.3 V 0.5 A 3.77-10 V SO8 TPS7333QD

Diodes8 1 D1 DIODE ZNR 25 V 0.5 W 5 mA AEC-Q101 SOD123 MMSZ5253BT1G9 1 D2 DIODE SW 150 MA 75 V SOD-323 1N4148WS

10 1 D3 DIODE ZNR 5.1 V 0.5 W SOD123 MMSZ5231BT1G11 2 D4,D8 LED RED SGL 30 MA SMT 0603 RED LED12 1 D5 DIODE ZNR 20 V 300 MW SOD523 BZT52C20T-713 1 D6 LED OR SGL 20 MA 0603 LED_ORANGE14 1 D7 LED GRN SGL 30 MA SMT 0603 LED_GREEN15 1 D9 DIODE ZNR -- 0.5 W 8.2 V SOD123 MMSZ8V2T1G

16 1 D10 DIODE BIDIR CAN BUS ESD PROTECTION 200 W 24 V AEC-Q101 SOT23PESD1CAN

17 1 D11 DIODE ESD PROTECTION 23 KV AEC-Q101 SOD323PESD1LIN

Capacitors18 3 C1,C52,C55 10 F CAP CER 10 F 25 V 20% X5R 0603

19

20 C2,C3,C4,C5,C12,C14,C15,C16,C17,C18,C22,C27,C28,C31,C35,C40,C41,C43,C44,

C54

0.1 F CAP CER 0.1 F 25 V 10% X8R 0603

20 1 C6 4700 PF CAP CER 4700 PF 25 V 10% X7R 080521 2 C7,C11 8.0 PF CAP CER 8.0 PF 50 V +/- 0.5 PF C0G 0402

22

20 C8,C9,C19,C20,C21,C26,C29,C30,C32,C33,C34,C36,C37,C38,C39,C42,C45,C49,C5

0,C51

0.022 F CAP CER 0.022 F 50 V 10% X7R AEC-Q200 0603

23 2 C10,C13 0.01 F CAP CER 0.01 F 50 V 10% X8R 060324 2 C23,C25 100 pF CAP CER 100 pF 100 V 5% C0G 060325 1 C24 2.2 F CAP CER 2.2 F 25 V 10% X5R 060326 1 C46 4.7 F CAP TANT 4.7 F 10 V 20% -- 060327 1 C47 0.01 F CAP CER 0.01 F 16 V 10% X7R 040228 1 C48 0.1 F CAP CER 0.1 F 16 V 10% X7R 040229 1 C53 4.7 F CAP CER 4.7 F 16 V 10% X5R 060330 2 C56,C57 1 CAP CER 1 F 25 V 10% X7R AEC-Q200 080531 1 C58 1000 PF CAP CER 1000 PF 50 V 10% C0G 0603

Resistors32 1 R1 4.7 K RES MF 4.70 K 1/16 W 1% 0402

33 9 R2,R6,R7,R8,R15,R17,R19,R23,R241.00 K RES MF 1.00 K1/16 W 1% AEC-Q200 0402

Board Bill of Materials


34 9 R3,R10,R13,R16,R26,R28,R30,R31,R3210.0 K RES MF 10.0 K 1/16 W 1% AEC-Q200 0402

35 2 R4,R5 60.4 RES MF 60.4 1/8 W 1% 080536 1 R9 1 M RES MF 1.0 M 1/16 W 1% AEC-Q200 040237 3 R11,R33,R34 0 RES MF ZERO 1/16 W -- AEC-Q200 040238 4 R12,R18,R21,R25 100 RES MF 100 1/16 W 5% AEC-Q200 040239 2 R14,R22 5.0 K RES MF 5.0 K 1/16 W 5% 040240 1 R20 47 K RES MF 47 K 1/16 W 1% 040241 2 R27,R29 560 RES MF 560 1/16 W 1% 0402

Switches, Connectors, Jumpers and Test Points42 1 F1 0.5 A FUSE FAST 0.5 A 63 V SMT 120643 1 JP1 HDR 1X6 TH 100MIL CTR 338H AU 150L HDR_1X644 4 JP2,JP3,JP4,JP5 HDR 1X10 TH 156MIL SP 580H SN 175L HDR_1X1045 1 J1 HDR 1X4 TH 100MIL CTR 338H AU 200L HDR_1X446 1 J2 HDR 2X3 TH 100MIL CTR 335H AU 95L HDR 2X347 1 J3 HDR 1X2 TH 100MIL SP 323H AU 130L HDR_1X2

48 1 J4 CON 5 USB_MICRO_B SKT RA SHLD SMT 0.65 MM SP 114H AU1050170001

49 1 L1 60 OHM IND FER BEAD 60 OHM@100 MHZ 500 MA -- 060350 1 L2 330 OHM IND FER BEAD 330 OHM@100 MHZ 2.5A -- SMT51 1 L3 IND CHK 2X51 UH 250 MA -30/+50% 1812 B82789C0513N00252 1 Q1 TRAN PNP PWR 1 A 60 V SOT-223 BCP52-16

53 5 TP1,TP3,TP7,TP9,TP11TEST POINT BLACK

TEST POINT BLACK 40 MIL DRILL 180 MIL TH 109L

54 6 TP2,TP4,TP5,TP6,TP8,TP10TEST POINT RED

TEST POINT RED 40 MIL DRILL 180 MIL TH 109L

55 1 Y1 8 MHz XTAL 8 MHZ -- -- SMT

Notes1. Freescale does not assume liability, endorse, or warrant components from external manufacturers are referenced in circuit drawings or tables.

While Freescale offers component recommendations in this configuration, it is the customer’s responsibility to validate their application.

Table 7. Bill of Materials(1)

Item Qty Schematic label VALUE DESCRIPTION Part Number

References


10 ReferencesFollowing are URLs where you can obtain information on related Freescale products and application solutions:

10.1 SupportVisit www.freescale.com/support for a list of phone numbers within your region.

10.2 WarrantyVisit www.freescale.com/warranty to submit a request for tool warranty.

Freescale.com Support Pages Description URL

KIT12XS6EVM Tool Summary Page www.freescale.com/KIT12XS6EVM

KITLIGHTEVB Tool Summary Page www.freescale.com/KITLIGHTEVB

MC33903 Product Summary Page http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=MC33903

MC07XS6517 Product Summary Page http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=MC12XS6

MC17XS6500 Product Summary Page http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=MC12XS6

S12G Product Summary Page http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=S12G

USBMULTILINKBDM Tool Summary Page http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=USBMULTILINKBDM

http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=KIT12XS6EVMhttp://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=MC33903www.freescale.com/KIT12XS6EVMhttp://www.freescale.com/webapp/sps/site/homepage.jsp?code=SUPPORTHOMEhttp://www.freescale.com/warrantyhttp://www.freescale.com/supporthttp://www.freescale.com/supporthttp://www.freescale.com/warrantyhttp://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=MC12XS6http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=MC12XS6www.freescale.com/KITLIGHTEVBhttp://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=S12Ghttp://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=USBMULTILINKBDM

Revision History


11 Revision HistoryRevision Date Description of Changes

1.0 10/2015 • Initial release

Document Number: KT12XS6EVMUGRev. 1.010/2015

Information in this document is provided solely to enable system and software implementers to use Freescale products.

There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits based

on the information in this document.

Freescale reserves the right to make changes without further notice to any products herein. Freescale makes no

warranty, representation, or guarantee regarding the suitability of its products for any particular purpose, nor does

Freescale assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any

and all liability, including without limitation consequential or incidental damages. “Typical” parameters that may be

provided in Freescale data sheets and/or specifications can and do vary in different applications, and actual performance

may vary over time. All operating parameters, including “typicals,” must be validated for each customer application by

customer’s technical experts. Freescale does not convey any license under its patent rights nor the rights of others.

Freescale sells products pursuant to standard terms and conditions of sale, which can be found at the following address:

freescale.com/SalesTermsandConditions.

Freescale and the Freescale logo are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off.

SMARTMOS is a trademark of Freescale Semiconductor, Inc. All other product or service names are the property of their

respective owners.

© 2015 Freescale Semiconductor, Inc.

How to Reach Us:Home Page: freescale.com

Web Support: freescale.com/support

http://www.freescale.com/SalesTermsandConditionshttp://www.freescale.com/http://www.freescale.com/support

KIT12XS6EVM Evaluation Board1 Important Notice2 Getting Started2.1 Kit Contents/Packing List2.2 Jump Start2.3 Required Equipment and Software2.4 System Requirements

3 Understanding the Board3.1 Block Diagram3.1.1 Device Features

4 Getting to Know the Hardware4.1 Board Overview4.2 Board Features4.3 Board Description4.4 LED Display4.5 Connectors4.6 Test Point Definitions4.7 USB Connector

5 Accessory KITLIGHTEVB Load Module6 Installing the Software and Setting up the Hardware6.1 Installing the GUI on your Computer6.2 Describing the GUI Interface6.3 Configuring the Hardware6.3.1 Step-by-step Instructions for Setting up the Hardware

7 Schematic8 Board Layout8.1 Silkscreen

9 Board Bill of Materials10 References10.1 Support10.2 Warranty

11 Revision History

Documents

KIT12XS6EVM Evaluation Board - NXP Semiconductors · 2019. 7. 17. · Getting Started KT12XS6EVMUG Rev. 1.0 4 Freescale Semiconductor, Inc. 2Getting Started 2.1 Kit Contents/Packing