Embed Size (px)
Citation preview
DECAL PLACEMENT11
* REPEAT SEVERAL TIMES* A REPETER PLUSIEURS FOIS
* CEMENT TOGETHER* A COLLER
* ALTERNATIVE ASSEMBLY* ENSEMBLAGE ALTERNATIVE
* REMOVE AND THROW AWAY* A RETIRER ET JETER
* DO NOT CEMENT* NE PAS COLLER
* OPTIONAL PARTS* PIECES EN OPTION
* DECAL * DECAL COMANIE
This paint guide is provided to complete this kit as shown on the box.
Ce guide de peintures est fourni pour reproduire le modèle réduit qui apparaît sur la boîte.
* Study the assembly drawings.* Each plastic part is identified by a number.* In the assembly drawings, some parts will be
marked by a star (★) to indicate chrome plated plastic.
* For better paint and decal adhesion, wash the plastic parts in a mild detergent solution. Rinse and let air dry.
* Check the fit of each piece before cementing in place.
* Use only cement for polystyrene plastic.* Scrape plating and paint from areas
to be cemented.* Allow paint to dry thoroughly before
handling parts.* Any unused parts may be discarded.
DECAL APPLICATION INSTRUCTIONS
1. Cut desired decal from sheet.2. Dip decal in water for a few seconds.3. Place wet decal on paper towel.4. Wait until decal is movable on paper backing.5. Place decal in position on model, face up and
slide backing away.6. Press out air bubbles with a soft damp cloth.7. Milkiness that may appear is for better decal
adhesion and will dry clear. Wipe away any excess adhesive.
8. Do not touch decal until fully dry.9. Allow the decals 48 hours to dry before
applying clear coat.
NOTE: Decals are compatible with setting solutions or solvents.
READ THIS BEFORE YOU BEGIN LIRE CE QUI SUIT AVANT DE COMMENCER
* Etudier les schémas de montage.* Chaque pièce en plastique est identifiée par un numéro.* Sur les schémas de montage, certaines pièces sont
marquées d'une étoile (★) pour indiquer qu'elles sont en plastique chromé.
* Pour une meilleure prise de la peinture et des autocollants, laver les pièces en plastique avec une solution détergente peu concentrée. Les rincer et les laisser sécher à l'air.
* Vérifier que chaque pièce s'ajuste bien avant de la coller en place.
* N'utiliser que de la colle pour polystyrène.* Gratter les parties à coller pour enlever le chrome et la peinture.* Laisser la peinture bien sécher avant de manipuler les pièces.* Toute pièce inutilisée peut être jetée.
DIRECTIVES D'APPLICATION DES AUTOCOLLANTS
1. Découper l'autocollant désiré de la feuille.2. Tremper l'autocollant dans de l'eau pendant quelques secondes.3. Placer l'autocollant mouillé sur une serviette en papier.4. Attendez que l'autocollant puisse être déplacé sur son
support en papier.5. Mettre l'autocollant en position sur le modèle face sur
le dessus et faire glisser le support pour l'enlever.6. Appuyer avec un chiffon doux humide pour éliminer les bulles d'air.7. La substance laiteuse qui peut apparaître est destinée à
améliorer l'adhésion de l'autocollant et devient incolore au séchage. Essuyer pour enlever tout excédent d'adhésif.
8. Ne pas toucher l'autocollant tant qu'il n'est pas bien sec.9. Laisser l'autocollant sécher pendant 48 heures avant
d'appliquer une couche transparente.REMARQUE: Les autocollants sont compatibles avec
les solutions de fixage ou les solvants.
'09 DODGE CHALLENGER SRT8 KIT 4220 85422000200
If you have any questions or comments, call our hotline at: (800) 833-3570or, please write to:
Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007Be sure to include the plan number (85422000200), part number, description, your return address and phone number.
Visit our website: www.revell.com
Revell Inc Elk Grove Village, IL. Copyright © 2009. All rights reserved.Kit 4220 - Page 8
Aluminum
Flat Black
Gloss Red
Gloss Hemi Orange
Semi gloss Black
Silver
Steel
Transparent Red
Turn Signal Amber
Aluminum
Noir mat
Rouge brillant
Orange brillant
Noir satiné
Argent
Acier
Rouge transparent
Ambre
The 2009 Dodge Challenger SRT8 is a modern version of the iconic Dodge Challenger of the early 70's. All the muscle car and sporty design is here: a 425 horse power engine, dual exhaust, front and rear spoilers, bucket seats and the famous bulged hood with functional air-intakes. In the 70's the Dodge Challenger was an awe-some ride and now it's even better. Your Revell model has an open-ing hood with a highly detailed 6.1-liter SRT HEMI® V8 engine, optional 20" chrome wheels, five spoke forged SRT8 or customwheels and authentic factory stock and custom decal graphics. Dodge and HEMI® are trademarks of Chrysler LLC. Dodge Challenger and their trade dress are used under license by Revell. © Chrysler LLC 2009.
48UPPER
RADIATOR HOSEFLAT BLACK
30CHASSIS
SEMI GLOSS BLACK
ENGINE ASSEMBLY1 REAR ASSEMBLY8
HOOD / MIRROR ASSEMBLY9
FINAL ASSEMBLY10
Kit 4220 - Page 2 Kit 4220 - Page 7
56RIGHT ENGINE
HALFGLOSS HEMI
ORANGE
55LEFT ENGINE
HALFGLOSS HEMI
ORANGE
69OIL FILTERGLOSS WHITE
67OIL PAN
ALUMINUM
68TRANSMISSION
PANALUMINUM
58CYLINDER
HEADALUMINUM
58CYLINDER
HEADALUMINUM
64INDUCTION MANIFOLDALUMINUM
57ENGINE FRONT
ALUMINUM
70A/C
COMPRESSORALUMINUM
46BELT /PULLEY
ALUMINUM(BELTS FLAT BLACK)
71ALTERNATOR
ALUMINUM
60VALVE COVER
SEMI GLOSS BLACK
60VALVE COVER
SEMI GLOSS BLACK
65RIGHT
EXHAUST MANIFOLD
STEEL
62RIGHT
INGNITION COILSEMI GLOSS
BLACK
61LEFT
INGNITION COILSEMI GLOSS
BLACK
72OIL FILLER
TUBESEMI GLOSS
BLACK
66LEFT
EXHAUST MANIFOLD
STEEL
19
1718
116RADIATORSEMI GLOSS
BLACK
43 ELECTRIC FANS
SEMI GLOSS BLACK
COMPLETED ENGINE
5LEFT
REAR VIEW MIRRORBODY COLOR
6RIGHT
REAR VIEW MIRRORBODY COLOR
52RIGHT
HOOD INSERTSEMI GLOSS BLACK
51LEFT
HOOD INSERTSEMI GLOSS
BLACK
★90RIGHT SIDE
MIRRORCHROME
★89LEFT
SIDE MIRRORCHROME
2HOOD
BODY COLOR
45AIR INTAKE
SEMIGLOSS BLACK
★98LEFT
EXHAUST TIPCHROME
★97RIGHT
EXHAUST TIPCHROME
★94TAILLIGHT
REFLECTORCHROME
★96GAS CAPCHROME107
TAILLIGHTTRANSPARENT REDSEMI GLOSS
BLACK
SEMI GLOSS BLACK
4REAR BUMPER
BODY COLOR
8REAR SPOILER
SEMI GLOSS BLACK
FRONT ASSEMBLY6 INTERIOR ASSEMBLY2
Kit 4220 - Page 3Kit 4220 - Page 6
16STEERING COLUMN
SEMI GLOSS BLACK
13DASHBOARD
SEMI GLOSS BLACK
17STEERING
WHEELSEMI GLOSS
BLACK
3 45
14 15 16
12-1354 6
7
10
44
43
42
11
9
8
BODY / INTERIOR / CHASSIS ASSEMBLY7
18RIGHT
BUCKET SEATSEMI GLOSS BLACK
40
41
40
21RIGHT
BUCKET SEAT BACKSEMI GLOSS BLACK
19 LEFT
BUCKET SEATSEMI GLOSS BLACK
22REAR SEAT
SEMI GLOSS BLACK
20 LEFT
BUCKET SEAT BACKSEMI GLOSS BLACK
106BRAKE
MASTER CYLINDERCLEAR
WITH SEMI GLOSS BLACK TOP
47FIRE WALLSEMI GLOSS
BLACK
SEMI GLOSS BLACK
(INTERIOR FLOOR)
A B
D
C
E
10 INTERIOR FLOOR
SHADED AREA ISBODY COLOR
23SHIFT LEVER
SEM IGLOSS BLACK
25CONSOLESEMI GLOSS
BLACK
26CONSOLE REARSEMI GLOSS BLACK
115ARM REST
SEMI GLOSS BLACK
11RIGHT
INTERIOR SIDESEMI GLOSS
BLACK
12LEFT
INTERIOR SIDESEMI GLOSS
BLACK
3FRONT BUMPER
BODY COLOR
104RIGHT
HEADLIGHT OUTER COVERCLEAR
103LEFT
HEADLIGHT OUTER COVERCLEAR
102RIGHT
HEADLIGHT INNER COVERCLEAR
101LEFT
HEADLIGHT INNER COVERCLEAR
★95DRIVING LIGHT REFLECTOR
CHROME
★92LEFT
HEADLIGHT REFLECTOR
CHROME
★93RIGHT
HEADLIGHT REFLECTORCHROME
★95DRIVING LIGHT REFLECTOR
CHROME
105DRIVING LIGHT LENS
CLEAR
50LOWER FRONT GRILLE
SEMI GLOSS BLACK
INTERIOR TO BODY
INTERIOR / BODY TO CHASSIS
41
41
41
CHASSIS ASSEMBLY3 WHEEL AND TIRE ASSEMBLY4
WINDOW ASSEMBLY5
Kit 4220 - Page 4 Kit 4220 - Page 5
FLAT BLACK
33STEERING
RACKALUMINUM
BUMP
BUMP
31FRONT
SUSPENSIONSEMI GLOSS
BLACK
34LEFT
FRONT STRUTSEMI GLOSS
BLACK
35RIGHT
FRONT STRUTSEMI GLOSS BLACK
41LOWER REARSUSPENSION
SEMI GLOSS BLACK
39REAR SHOCKS
SEMI GLOSS BLACK
42COIL SPRINGS
SEMI GLOSS BLACK
36ENGINE SERVICE
COVERSEMI GLOSS BLACK
78REAR
EXHAUST SYSTEMALUMINUM
77FRONT
EXHAUST SYSTEMALUMINUM
30CHASSIS
SEMI GLOSS BLACK
37RIGHT
REAR AXLE ALUMINUM
38LEFT
REAR AXLE ALUMINUM
TIRE
TIRE
★85STOCK
FRONT WHEELCHROME
★87FRONT
CUSTOMWHEELCHROME
★88REAR
CUSTOMWHEELCHROME
★86STOCK
REAR WHEELCHROME
SMALL HOLES FOR REAR
AXLE
METAL AXLE 75LEFT
REAR BRAKESTEEL
73LEFT
FRONT BRAKESTEEL
LARGER HOLES ON FRONT FRONT ONLY
STRUTS HAS TO BE IN THE CENTER OVER THE BUMP
ON THE SUSPENSION
79PIN RETAINER
METAL PIN
74RIGHT
FRONT BRAKESTEEL
76RIGHT
REAR BRAKESTEEL
GLOSS RED
GLOSS RED
A B
C
D★91
REAR VIEW MIRRORCHROME
24OVERHEAD CONSOLE
AND SUN VISORSSEMI GLOSS BLACK
27THIRD
BRAKE LIGHTSEMI GLOSS BLACK
100WINDSHIELD
CLEAR
110REAR WINDOW
CLEAR
112RIGHT SIDE
WINDOWCLEAR
111LEFT SIDE WINDOW
CLEAR
1BODY
BODY COLOR
SEMI GLOSS BLACK
GLOSS RED
2
2
CHASSIS ASSEMBLY3 WHEEL AND TIRE ASSEMBLY4
WINDOW ASSEMBLY5
Kit 4220 - Page 4 Kit 4220 - Page 5
FLAT BLACK
33STEERING
RACKALUMINUM
BUMP
BUMP
31FRONT
SUSPENSIONSEMI GLOSS
BLACK
34LEFT
FRONT STRUTSEMI GLOSS
BLACK
35RIGHT
FRONT STRUTSEMI GLOSS BLACK
41LOWER REARSUSPENSION
SEMI GLOSS BLACK
39REAR SHOCKS
SEMI GLOSS BLACK
42COIL SPRINGS
SEMI GLOSS BLACK
36ENGINE SERVICE
COVERSEMI GLOSS BLACK
78REAR
EXHAUST SYSTEMALUMINUM
77FRONT
EXHAUST SYSTEMALUMINUM
30CHASSIS
SEMI GLOSS BLACK
37RIGHT
REAR AXLE ALUMINUM
38LEFT
REAR AXLE ALUMINUM
TIRE
TIRE
★85STOCK
FRONT WHEELCHROME
★87FRONT
CUSTOMWHEELCHROME
★88REAR
CUSTOMWHEELCHROME
★86STOCK
REAR WHEELCHROME
SMALL HOLES FOR REAR
AXLE
METAL AXLE 75LEFT
REAR BRAKESTEEL
73LEFT
FRONT BRAKESTEEL
LARGER HOLES ON FRONT FRONT ONLY
STRUTS HAS TO BE IN THE CENTER OVER THE BUMP
ON THE SUSPENSION
79PIN RETAINER
METAL PIN
74RIGHT
FRONT BRAKESTEEL
76RIGHT
REAR BRAKESTEEL
GLOSS RED
GLOSS RED
A B
C
D★91
REAR VIEW MIRRORCHROME
24OVERHEAD CONSOLE
AND SUN VISORSSEMI GLOSS BLACK
27THIRD
BRAKE LIGHTSEMI GLOSS BLACK
100WINDSHIELD
CLEAR
110REAR WINDOW
CLEAR
112RIGHT SIDE
WINDOWCLEAR
111LEFT SIDE WINDOW
CLEAR
1BODY
BODY COLOR
SEMI GLOSS BLACK
GLOSS RED
2
2
FRONT ASSEMBLY6 INTERIOR ASSEMBLY2
Kit 4220 - Page 3Kit 4220 - Page 6
16STEERING COLUMN
SEMI GLOSS BLACK
13DASHBOARD
SEMI GLOSS BLACK
17STEERING
WHEELSEMI GLOSS
BLACK
3 45
14 15 16
12-1354 6
7
10
44
43
42
11
9
8
BODY / INTERIOR / CHASSIS ASSEMBLY7
18RIGHT
BUCKET SEATSEMI GLOSS BLACK
40
41
40
21RIGHT
BUCKET SEAT BACKSEMI GLOSS BLACK
19 LEFT
BUCKET SEATSEMI GLOSS BLACK
22REAR SEAT
SEMI GLOSS BLACK
20 LEFT
BUCKET SEAT BACKSEMI GLOSS BLACK
106BRAKE
MASTER CYLINDERCLEAR
WITH SEMI GLOSS BLACK TOP
47FIRE WALLSEMI GLOSS
BLACK
SEMI GLOSS BLACK
(INTERIOR FLOOR)
A B
D
C
E
10 INTERIOR FLOOR
SHADED AREA ISBODY COLOR
23SHIFT LEVER
SEM IGLOSS BLACK
25CONSOLESEMI GLOSS
BLACK
26CONSOLE REARSEMI GLOSS BLACK
115ARM REST
SEMI GLOSS BLACK
11RIGHT
INTERIOR SIDESEMI GLOSS
BLACK
12LEFT
INTERIOR SIDESEMI GLOSS
BLACK
3FRONT BUMPER
BODY COLOR
104RIGHT
HEADLIGHT OUTER COVERCLEAR
103LEFT
HEADLIGHT OUTER COVERCLEAR
102RIGHT
HEADLIGHT INNER COVERCLEAR
101LEFT
HEADLIGHT INNER COVERCLEAR
★95DRIVING LIGHT REFLECTOR
CHROME
★92LEFT
HEADLIGHT REFLECTOR
CHROME
★93RIGHT
HEADLIGHT REFLECTORCHROME
★95DRIVING LIGHT REFLECTOR
CHROME
105DRIVING LIGHT LENS
CLEAR
50LOWER FRONT GRILLE
SEMI GLOSS BLACK
INTERIOR TO BODY
INTERIOR / BODY TO CHASSIS
41
41
41
48UPPER
RADIATOR HOSEFLAT BLACK
30CHASSIS
SEMI GLOSS BLACK
ENGINE ASSEMBLY1 REAR ASSEMBLY8
HOOD / MIRROR ASSEMBLY9
FINAL ASSEMBLY10
Kit 4220 - Page 2 Kit 4220 - Page 7
56RIGHT ENGINE
HALFGLOSS HEMI
ORANGE
55LEFT ENGINE
HALFGLOSS HEMI
ORANGE
69OIL FILTERGLOSS WHITE
67OIL PAN
ALUMINUM
68TRANSMISSION
PANALUMINUM
58CYLINDER
HEADALUMINUM
58CYLINDER
HEADALUMINUM
64INDUCTION MANIFOLDALUMINUM
57ENGINE FRONT
ALUMINUM
70A/C
COMPRESSORALUMINUM
46BELT /PULLEY
ALUMINUM(BELTS FLAT BLACK)
71ALTERNATOR
ALUMINUM
60VALVE COVER
SEMI GLOSS BLACK
60VALVE COVER
SEMI GLOSS BLACK
65RIGHT
EXHAUST MANIFOLD
STEEL
62RIGHT
INGNITION COILSEMI GLOSS
BLACK
61LEFT
INGNITION COILSEMI GLOSS
BLACK
72OIL FILLER
TUBESEMI GLOSS
BLACK
66LEFT
EXHAUST MANIFOLD
STEEL
19
1718
116RADIATORSEMI GLOSS
BLACK
43 ELECTRIC FANS
SEMI GLOSS BLACK
COMPLETED ENGINE
5LEFT
REAR VIEW MIRRORBODY COLOR
6RIGHT
REAR VIEW MIRRORBODY COLOR
52RIGHT
HOOD INSERTSEMI GLOSS BLACK
51LEFT
HOOD INSERTSEMI GLOSS
BLACK
★90RIGHT SIDE
MIRRORCHROME
★89LEFT
SIDE MIRRORCHROME
2HOOD
BODY COLOR
45AIR INTAKE
SEMIGLOSS BLACK
★98LEFT
EXHAUST TIPCHROME
★97RIGHT
EXHAUST TIPCHROME
★94TAILLIGHT
REFLECTORCHROME
★96GAS CAPCHROME107
TAILLIGHTTRANSPARENT REDSEMI GLOSS
BLACK
SEMI GLOSS BLACK
4REAR BUMPER
BODY COLOR
8REAR SPOILER
SEMI GLOSS BLACK
DECAL PLACEMENT11
* REPEAT SEVERAL TIMES* A REPETER PLUSIEURS FOIS
* CEMENT TOGETHER* A COLLER
* ALTERNATIVE ASSEMBLY* ENSEMBLAGE ALTERNATIVE
* REMOVE AND THROW AWAY* A RETIRER ET JETER
* DO NOT CEMENT* NE PAS COLLER
* OPTIONAL PARTS* PIECES EN OPTION
* DECAL * DECAL COMANIE
This paint guide is provided to complete this kit as shown on the box.
Ce guide de peintures est fourni pour reproduire le modèle réduit qui apparaît sur la boîte.
* Study the assembly drawings.* Each plastic part is identified by a number.* In the assembly drawings, some parts will be
marked by a star (★) to indicate chrome plated plastic.
* For better paint and decal adhesion, wash the plastic parts in a mild detergent solution. Rinse and let air dry.
* Check the fit of each piece before cementing in place.
* Use only cement for polystyrene plastic.* Scrape plating and paint from areas
to be cemented.* Allow paint to dry thoroughly before
handling parts.* Any unused parts may be discarded.
DECAL APPLICATION INSTRUCTIONS
1. Cut desired decal from sheet.2. Dip decal in water for a few seconds.3. Place wet decal on paper towel.4. Wait until decal is movable on paper backing.5. Place decal in position on model, face up and
slide backing away.6. Press out air bubbles with a soft damp cloth.7. Milkiness that may appear is for better decal
adhesion and will dry clear. Wipe away any excess adhesive.
8. Do not touch decal until fully dry.9. Allow the decals 48 hours to dry before
applying clear coat.
NOTE: Decals are compatible with setting solutions or solvents.
READ THIS BEFORE YOU BEGIN LIRE CE QUI SUIT AVANT DE COMMENCER
* Etudier les schémas de montage.* Chaque pièce en plastique est identifiée par un numéro.* Sur les schémas de montage, certaines pièces sont
marquées d'une étoile (★) pour indiquer qu'elles sont en plastique chromé.
* Pour une meilleure prise de la peinture et des autocollants, laver les pièces en plastique avec une solution détergente peu concentrée. Les rincer et les laisser sécher à l'air.
* Vérifier que chaque pièce s'ajuste bien avant de la coller en place.
* N'utiliser que de la colle pour polystyrène.* Gratter les parties à coller pour enlever le chrome et la peinture.* Laisser la peinture bien sécher avant de manipuler les pièces.* Toute pièce inutilisée peut être jetée.
DIRECTIVES D'APPLICATION DES AUTOCOLLANTS
1. Découper l'autocollant désiré de la feuille.2. Tremper l'autocollant dans de l'eau pendant quelques secondes.3. Placer l'autocollant mouillé sur une serviette en papier.4. Attendez que l'autocollant puisse être déplacé sur son
support en papier.5. Mettre l'autocollant en position sur le modèle face sur
le dessus et faire glisser le support pour l'enlever.6. Appuyer avec un chiffon doux humide pour éliminer les bulles d'air.7. La substance laiteuse qui peut apparaître est destinée à
améliorer l'adhésion de l'autocollant et devient incolore au séchage. Essuyer pour enlever tout excédent d'adhésif.
8. Ne pas toucher l'autocollant tant qu'il n'est pas bien sec.9. Laisser l'autocollant sécher pendant 48 heures avant
d'appliquer une couche transparente.REMARQUE: Les autocollants sont compatibles avec
les solutions de fixage ou les solvants.
'09 DODGE CHALLENGER SRT8 KIT 4220 85422000200
If you have any questions or comments, call our hotline at: (800) 833-3570or, please write to:
Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007Be sure to include the plan number (85422000200), part number, description, your return address and phone number.
Visit our website: www.revell.com
Revell Inc Elk Grove Village, IL. Copyright © 2009. All rights reserved.Kit 4220 - Page 8
Aluminum
Flat Black
Gloss Red
Gloss Hemi Orange
Semi gloss Black
Silver
Steel
Transparent Red
Turn Signal Amber
Aluminum
Noir mat
Rouge brillant
Orange brillant
Noir satiné
Argent
Acier
Rouge transparent
Ambre
The 2009 Dodge Challenger SRT8 is a modern version of the iconic Dodge Challenger of the early 70's. All the muscle car and sporty design is here: a 425 horse power engine, dual exhaust, front and rear spoilers, bucket seats and the famous bulged hood with functional air-intakes. In the 70's the Dodge Challenger was an awe-some ride and now it's even better. Your Revell model has an open-ing hood with a highly detailed 6.1-liter SRT HEMI® V8 engine, optional 20" chrome wheels, five spoke forged SRT8 or customwheels and authentic factory stock and custom decal graphics. Dodge and HEMI® are trademarks of Chrysler LLC. Dodge Challenger and their trade dress are used under license by Revell. © Chrysler LLC 2009.
