Kisumu Kamau Link Acceptance DOC

FlexiPacket Microwave

FlexiPacket LinkField CommissioningTests Sheets Report

Customerairtel

Ed. 01 FlexiPacket LinkField Commissioning Tests Sheets-1/27-

234

airtel

Kamau-kisumu

Equipment:

Customer:

FPMR

Link:

Kania

Work Order:

Country:

04/12/2013

The attached test sheets show the results of the tests carried out

We here undersign to certificate that the link under test fully complies with thetechnical specifications as per contract.

For NSN For Customer

Name:

Signature:

Name:

Signature:

DATE 04/12/2013

Identification Station A(10.10.10.1):

123

Identification Station B1(N.A.):

456

FLEXIPACKET RADIO LINK ACCEPTANCE REPORT

The commissioning of the referred link has been concluded on


Relevant remarks:

Relevant notes for Station A:

Relevant notes for Station B1:

Common Notes:

For NSN

Signature:Signature:

Name:Name:

For Customer

DATE 04/12/2013


Date Ed Note

2013-04-12 12:35:18 01 First Issue

1 REVISION LIST


2.1 Tools and Test Instruments Basic Test Instruments suggested for Line-up and commissioning

2 TEST INSTRUMENT LIST

Test Instruments Notes

Personal Computer / Laptop(Minimum HW Requirements)(Suggested Qty 2)

* CPU Pentium 1,6 Ghz or higher* 256 Mbyte RAM minimum (Suggested 512)* Color monitor with resolution of 1024x768 at least* Video card with minimum resolution of 1024x768* 10 Gbyte Hard-disk minimum* CD-ROM drive* Mouse* Ethernet network card (RJ45 interface)

Personal Computer / Laptop (SWRequirements)

* Microsoft Windows XP Professional* TCP/IP communication protocol installed* Microsoft office 2000 / XP or 2003* Web Browser program with Java environmentinstalled + Microsoft Internet Higher than Explorer 5.5 orMozilla Firefox (latest version is preferred) + Java Runtime environment (Version 1.6. orlatest version is preferred)* HyperTerminal application SW (embeddedwindows application)* FTP client + FileZilla version 2.2.32 or higher (in LCT pack)* LCT engine with plugins

TDM test equipment (SuggestedQty 1) E1 TDM generator / analyzer

Multimeters Suggested Analogic or Digital Multimeter

Accessories Notes

ETH Cat 5e cable type RJ45 Straight and Cross type both end cabled (all wire)

E1/T1 120 Ohm Cable with RJ48Termination (one end)

Pin Out based to T1/E1 Connectors on FlexiPacketHub

Cable for antenna alignment BNC / Banana (must be build in Field)


Tools Notes

Crimping accessories Tools foroutdoor Eth and PS cables(Mandatory)

RJ45 Connectors Crimping Tool(Mandatory)

Strip Pliers and Cable stripperaccessories Tools(recommended)

Technical Tools bag


Fill the requested form with requested data according to the installed systemand verify the data with the ones reported in the Installation Manual and ProjectSpecifications.

Remarks: Please list all items to be corrected.

3.1 FlexiPacket Hub 800 R2.0 Installation Check List Summary

3 INSTALLATION CHECK LIST

FlexiPacket Hub 800 R2.0

Indoor assembly and Fixing [ ] Yes [ ] No [ ] N.A.

Power supply cables (Qty ____) [ ] Yes [ ] No [ ] N.A.

Checking of Power supply source [ ] Yes [ ] No [ ] N.A.

Grounding Indoor Units [ ] Yes [ ] No [ ] N.A.

ETH Services Cables on Indoor units (status and fixing) [ ] Yes [ ] No [ ] N.A.

TDM Services Cables on Indoor units (status and fixing) [ ] Yes [ ] No [ ] N.A.

Alarm and Services Cables [ ] Yes [ ] No [ ] N.A.

Management System Connections and Cabling [ ] Yes [ ] No [ ] N.A.

Is the system ready for Line-up and commissioning? [ ] Yes [ ] No [ ] N.A.

Needed corrective measures to be completed before Line-up: [ ] Yes [ ] No [ ] N.A.

Is another check necessary prior to start the Line-up? [ ] Yes [ ] No [ ] N.A.

3.2 FlexiPacket Hub 800 R2.0 Equipment configuration parameters

Connected network elements summary

Ethernet interface(slot # / interface #)

Connectednetwork element

Network elementIP address

NewInstallation (**)

IDU-A GE 0/4 FlexiPacket MultiRadio R2.1 (Packet)

10.10.10.2 Yes


Notes

(*) Specify the network element type. Possibilities are: - FlexiPacket Radio - FlexiPacket Radio HC - FlexiPacket MultiRadio (P) - FlexiPacket Hub 2200 - FlexiPacket Hub 1200 - BTS Integrated Solution (add detailed model info) - 3rd Party Integrated Solution (add detailed model info)(**) Select No for FlexiPacket Radios belonging to radio links already accepted (set Yesif the related NE has been added to the IDU during this session of the CT)

Equipment configuration parameters

Ethernet Interface

Ethernetinterface

AdminStatus

OperationalStatus Mode

LocalManagement Description

IDU-A GE 0/1 down down NNI N.A.

IDU-A GE 0/2 down down NNI N.A.

IDU-A GE 0/3 up down UNI N.A.

IDU-A GE 0/4 up up NNI tagged

E1 Interface

TDM interface AdminStatusOperational

Status Framing Tx Clock Option

IDU-A PDH 0/1 down down E1CRC System







InterWorking Function

IP Address 0.0.0.0

Subnet Mask 0.0.0.0

Default Gateway 0.0.0.0

Mac Address 00:40:43:b6:0e:e2

TDM interface AdminStatusOperational

Status Framing Tx Clock Option











Synch-E Port Status

Equipment Synchronization parameters

Role SSM

IDU-A GE 0/1 master disable

IDU-A GE 0/2 master disable

IDU-A GE 0/3 slave disable

IDU-A GE 0/4 slave disable


Clock Source Priority

Priority Source Type Port Quality Level Status

N.A. N.A. N.A. N.A. N.A.

Current clock source type N.A.

Current clock source port N.A.

Clock source revision time (s) 300


4.2 Breakers / Fuse Used on FlexiPacket Hub 800 R2.0

4.1 DC Voltage Power supply on FlexiPacket Hub 800 R2.0

Primary Secondary

Power Supply Voltage _____ Volt (DC) _____ Volt (DC)

Primary Secondary

Breakers Type (maxcurrent value)

_____ Amperes _____ Amperes

4 FlexiPacket Hub 800 R2.0 SYSTEM CHECK AND MEASURE


5.1 FlexiPacket Hub 800 R2.0 Ethernet HW Port Validation

Ethernet interface(slot # / interface #) Ethernet HW Port validation result

IDU-A GE 0/1 FAILED

IDU-A GE 0/2 FAILED

IDU-A GE 0/3 FAILED

5 FlexiPacket Hub 800 R2.0 TEST RESULTS

5.2 FlexiPacket Hub 800 R2.0 E1 HW Port Validation

5.3 FlexiPacket Hub 800 R2.0 Line-Up Test results

Slot#/Port#Station A

Local NE Type(IP address)

Remote NE Type(IP address) Test Result

IDU-A GE 0/4 FPH800(10.10.10.1) FPMR(P)(10.10.10.2) PASSED

5.4 FlexiPacket Hub 800 R2.0 Link Validation Test results




IDU-A GE 0/4 FPH800(10.10.10.1) FPMR(P)(null) no peer exists

5.5 FlexiPacket Hub 800 R2.0 e2e Connectivity check Test results




IDU-A GE 0/4 FPH800(10.10.10.1) no remote IDUexists


Fill the requested form with requested data according to the installed systemand verify the data with the ones reported in the Installation Manual and ProjectSpecifications.

5.6 FlexiPacket Multi Radio R2.1 (Packet) Installation Check List Summary

Station A Station B1

Basic Items Main and ProtectionSystemMain and Protection

System

Antennas Assembly (XD Mechanicalcompatibility) [ ] Yes [ ] No [ ] N.A. [ ] Yes [ ] No [ ] N.A.

Antennas Assembly (FH Mechanicalcompatibility) [ ] Yes [ ] No [ ] N.A. [ ] Yes [ ] No [ ] N.A.

ODUs Fixing [ ] Yes [ ] No [ ] N.A. [ ] Yes [ ] No [ ] N.A.

Grounding ODUs [ ] Yes [ ] No [ ] N.A. [ ] Yes [ ] No [ ] N.A.

Eth Outdoor Cables status (status andfixing) [ ] Yes [ ] No [ ] N.A. [ ] Yes [ ] No [ ] N.A.

Eth Outdoor Cables grounding [ ] Yes [ ] No [ ] N.A. [ ] Yes [ ] No [ ] N.A.

DC Power Outdoor Cables status(status and fixing) [ ] Yes [ ] No [ ] N.A. [ ] Yes [ ] No [ ] N.A.

DC Power Outdoor Cables grounding [ ] Yes [ ] No [ ] N.A. [ ] Yes [ ] No [ ] N.A.

Additional Items(site andconfiguration dependency)

Main and ProtectionSystem

Main and ProtectionSystem

ODUs Mounting / Coupler Kit (XDMechanical compatibility) [ ] Yes [ ] No [ ] N.A. [ ] Yes [ ] No [ ] N.A.

ODUs Mounting / Coupler Kit (FHMechanical compatibility) [ ] Yes [ ] No [ ] N.A. [ ] Yes [ ] No [ ] N.A.

ID Station A(10.10.10.1):123 - ID Station B1(N.A.):456

RADIO LINK on Port IDU-A GE 0/4,


Is the system ready for Line-up and commissioning? [ ] Yes [ ] No [ ] N.A.

Needed corrective measures to be completed before Line-up: [ ] Yes [ ] No [ ] N.A.

Is another check necessary prior to start the Line-up? [ ] Yes [ ] No [ ] N.A.


Flexible waveguide assembly andfixing (_____ cm) [ ] Yes [ ] No [ ] N.A. [ ] Yes [ ] No [ ] N.A.

Power Injector[ ] N.A.[ ] Indoor version[ ] Outdoor version

[ ] N.A.[ ] Indoor version[ ] Outdoor version

ETH and DC cables on Power Injector [ ] Yes [ ] No [ ] N.A. [ ] Yes [ ] No [ ] N.A.

Eth Repeater (Qty ____) [ ] Yes [ ] No [ ] N.A. [ ] Yes [ ] No [ ] N.A.

Remarks: Please list all items to be corrected.

6 SYSTEM COMPOSITION SUMMARY

6.1 System Configuration Type

Units Station A Station B1

1+0 system with integrated antenna [ ] [ ]

1+0 system with independent antenna [ ] [ ]

1+1 protected system with integrated antenna [ ] [ ]

1+1 protected system with independent antenna [ ] [ ]

[ ] [ ]

[ ] [ ]


6.2 Composition, Serial numbers and active Product Software on FlexiPacket Hub 800 R2.0


Notes

(*) If applicable

(*) If applicable

(*) If applicable

Main ODU

Station

ProtectionODU (*)

A

Main ODU

Station

ProtectionODU (*)

B1

IDU type FlexiPacket Hub800 R2.0

FlexiPacket Hub800 R2.0

N.A. N.A.

ODU SystemType

1+0 N.A. N.A. N.A.

IDU Ethernetinterface(slot # /

interface #)

IDU-A GE 0/4 N.A. N.A. N.A.

IDU IP address 10.10.10.1 10.10.10.1 N.A. N.A.

ODU IP address 10.10.10.2 N.A. N.A. N.A.



NSN Code / version itemcode

T555800MB.00--A3B N.A.

Serial Number RY124513943 N.A.Software Code (Active

Software Load)2.8.32 N.A.

Software Code (StandbySoftware Load)

2.8.32 N.A.


Description Station A Station B1

System Name N.A.

System Location N.A.Contactinformation

N.A.

SystemDescription

flexiMwrFlexiPacket Hub 800 N.A.

User data N.A. N.A.



6.3 Composition and Serial number on FlexiPacket Multi Radio R2.1 (Packet)

Equipment typeMain or single

ODU

Station

ProtectionODU (*)

A

Main or singleODU

Station

ProtectionODU (*)

B1

NSN Code /version item code

T55715B0.53--B0

N.A. N.A. N.A.

Serial Number D6124263530 N.A. N.A. N.A.


(*) If applicable

6.4 Product Inventory Data (HW PID) on FlexiPacket Multi Radio R2.1 (Packet)

(*) If applicable(**)This is the SN of the RF part, the SN in the table above is the one related tothe whole ODU

Main or singleODU

Station

ProtectionODU (*)

A

Main or singleODU

Station

ProtectionODU (*)

B1

Serial Number(**) D6124263412 N.A. N.A. N.A.

Hardware Code T55715B N.A. N.A. N.A.

Firmware Code 448-025/72 N.A. N.A. N.A.


6.5 NE Info on FlexiPacket Multi Radio R2.1 (Packet)

DescriptionMain or single

ODU

Station

ProtectionODU (*)

A

Main or singleODU

Station

ProtectionODU (*)

B1

System Name TRAINING N.A. N.A. N.A.

System Location NBP N.A. N.A. N.A.Contact

information+254 N.A. N.A. N.A.



(*) If applicable(**) Take into account the possibility to extend the User data up to theirbiggest value (xxx bytes)

(*) The IP Gateway is not mandatory

6.6 Networking Configurations on FlexiPacket Hub 800 R2.0

If no DCN Planning configuration is available (or in case of a stand alone link) it issuggested to configure the following IP address


ODU

Station

ProtectionODU (*)

A

Main or singleODU

Station

ProtectionODU (*)

B1

SystemDescription

FPMR ODU N.A. N.A. N.A.

User data(**) N.A. N.A. N.A. N.A.


In Band IP Address 10.10.10.1 N.A.In Band Subnet

Mask255.255.255.0 N.A.

In Band DefaultGateway

10.10.10.254 N.A.

In Band 2nd DefaultGateway

N.A. N.A.

Management VLAN(defined by

CommissioningTool)

127 N.A.


Description Value

IP Address 10.10.10.2 (Station A) 10.10.10.3(Station Bx)

Subnet Mask 255.255.255.0

Default Gateway (*)

6.7 Networking Configurations on FlexiPacket Multi Radio R2.1 (Packet)



(*) If applicable


ODU

Station

ProtectionODU (*)

A

Main or singleODU

Station

ProtectionODU (*)

B1

In Use IP Address 10.10.10.2 N.A. N.A. N.A.In Use Subnet

Mask255.255.255.0 N.A. N.A. N.A.

In Use DefaultGateway

10.10.10.254 N.A. N.A. N.A.

ManagementVLAN(defined byCommissioning

Tool)

127 N.A. N.A. N.A.

DHCP Client disable N.A. N.A. N.A.

If no DCN Planning configuration is available (or in case of a stand alone link) it issuggested to configure the following IP address

(*) If applicable(**) The IP Gateway is not mandatory


ODU

Station

ProtectionODU (*)

A

Main or singleODU

Station

ProtectionODU (*)

B1

Data and Timesetting(Manual

setting)

2013-04-12 15:35:20

N.A. N.A. N.A.

SNTP enabled disable N.A. N.A. N.A.Time server IP

Address0.0.0.0 N.A. N.A. N.A.

Time zone (GMT) GreenwichMean Time

N.A. N.A. N.A.



ODU

Station

ProtectionODU (*)

A

Main or singleODU

Station

ProtectionODU (*)

B

IP Address 10.10.10.4 10.10.10.6 10.10.10.5 10.10.10.7

Subnet Mask 255.255.255.0 255.255.255.0 255.255.255.0 255.255.255.0Default Gateway

(**)DHCP Client Disable Disable Disable Disable


(*) If applicable


ODU

Station

ProtectionODU (*)

A

Main or singleODU

Station

ProtectionODU (*)

B1

Daylight Savingtime

disable N.A. N.A. N.A.

6.8 Product and SW Data on FlexiPacket Multi Radio R2.1 (Packet)

6.9 License Data on FlexiPacket Hub 800 R2.0

EquipmentSoftware

Inventory DataItems

Main or singleODU

Station

ProtectionODU (*)

A

Main or singleODU

Station

ProtectionODU (*)

B1

Software Code(Active Software

Load)

T557BSW2.50 N.A. N.A. N.A.

Software Code(Stand-by

Software Load)

T557BSW2.50 N.A. N.A. N.A.

Software Release& Build(ActiveSoftware Load)

2.5.6317 N.A. N.A. N.A.

Software Release& Build(Stand-bySoftware Load)

2.5.6317 N.A. N.A. N.A.

FPGA (RunVersion)

2.5.86 N.A. N.A. N.A.

FPGA (Stand-byVersion)

2.5.86 N.A. N.A. N.A.

Modem (RunVersion)

2.6.22 N.A. N.A. N.A.

Modem (Stand-byVersion)

2.6.22 N.A. N.A. N.A.



Ethernet OAM Not Active

MSTP/RSTP Not Active

1588V2.0 Not Active


(*) If applicable



Securemanagement

Not Active

6.10 License Data on FlexiPacket Multi Radio R2.1 (Packet)

EquipmentSoftware

Inventory DataItems

Main or singleODU

Station

ProtectionODU (*)

A

Main or singleODU

Station

ProtectionODU (*)

B1

Max Capacity is20 Mbps

ACM Not AllowedSecurity Not

AllowedFrequency/Space

Diversity NotAllowed

Cochannel NotAllowed

N.A. N.A. N.A.


6.11 FlexiPacket Multi Radio R2.1 (Packet) Equipment configuration parameters

Main or singleODU

Station

ProtectionODU (*)

A

Main or singleODU

Station

ProtectionODU (*)

B1

BB/Modemconfiguration

----- ----- ----- -----

Radio PortOperationalStatus

DOWN N.A. N.A. N.A.

Radio PortAdministrativeStatus

DOWN N.A. N.A. N.A.

R ChannelLength (leaveempty if notavailable)

N.A. N.A. N.A. N.A.



Main or singleODU

Station

ProtectionODU (*)

A

Main or singleODU

Station

ProtectionODU (*)

B1

Staticmodulation(ifapplicable theTX/RX Side ACMEnabled checkbox is notflagged)

disabled disabled disabled disabled

Staticmodulation TXprofile ID

QPSK N.A. N.A. N.A.

AdaptiveModulation(ifapplicable theTX Side ACMEnabled checkbox is flagged)

disabled disabled disabled disabled

In use TX profileID

QPSK N.A. N.A. N.A.

In use RX profileID

N.A. N.A. N.A. N.A.

Most Robust RXprofile ID

1 N.A. N.A. N.A.

Most Efficient RXprofile ID

1 N.A. N.A. N.A.

Modulation(from Detailsbutton w/ Staticmodulationenabled)

N.A N.A. N.A. N.A.

ChannelBandwidth (fromDetails button)

14MHz N.A. N.A. N.A.

Measured S/MSE[dB] (fromDetails buttonw/ TX Side ACMenabled)-----SNR in case ofFPR HC

20.3 N.A. N.A. N.A.

ATPC enabled(YES/NOT)

NOT N.A. N.A. N.A.

Max TX power[dBm]

23 N.A. N.A. N.A.

Max RSL [dBm](only when theATPC is enabled)

-73 N.A. N.A. N.A.

RFConfiguration

----- ----- ----- -----

TX Frequencyvalue [kHz]

15200000 N.A. N.A. N.A.


(*) If applicable

Main or singleODU

Station

ProtectionODU (*)

A

Main or singleODU

Station

ProtectionODU (*)

B1

RX Frequencyvalue [kHz]

14780000 N.A. N.A. N.A.

DuplexerParameters

----- ----- ----- -----

Min TXFrequency [kHz]

15187000 N.A. N.A. N.A.

Max TXFrequency [kHz]

15363000 N.A. N.A. N.A.

Shift Frequency[kHz]

250 N.A. N.A. N.A.

ChannelBandwidth[MHz]

14MHz N.A. N.A. N.A.

SystemControllerconfiguration

----- ----- ----- -----

Selection ofSynch Flow

N.A. N.A. N.A. N.A.

PLL WorkingMode Status

freeRun N.A. N.A. N.A.

Main or singleODU

Station

ProtectionODU (*)

A

Main or singleODU

Station

ProtectionODU (*)

B1

GbeConfiguration

----- ----- ----- -----

OperationalStatus

DOWN N.A. N.A. N.A.

AdministrativeStatus

DOWN N.A. N.A. N.A.

MDI/MDIXAutosensing

automatic N.A. N.A. N.A.

AutonegotiationProtocol

complete N.A. N.A. N.A.

AutonegotiationStatus

enable N.A. N.A. N.A.

Speed andduplex Selection(if theautonegotiationis disabled)

100BaseTXHD N.A. N.A. N.A.

Master/SlaveResolution

master N.A. N.A. N.A.

Master/SlaveSelection

automatic N.A. N.A. N.A.



(*) If applicable

(*) If applicable

6.12 RF Measurements

6.13 Outdoors ODUs Cables status

(*) If applicable

Main or singleODU

Station

ProtectionODU (*)

A

Main or singleODU

Station

ProtectionODU (*)

B1

TX OperationalStatus

squelch N.A. N.A. N.A.

TX Power Level[dBm]

17 N.A. N.A. N.A.

RX Power Level[dBm]

-96 N.A. N.A. N.A.

Temperature 43degreecentigrade

N.A. N.A. N.A.


Main or singleODU

Station

ProtectionODU (*)

A

Main or singleODU

Station

ProtectionODU (*)

B1

Eth Cable Lengthto ODU

_____meters _____meters _____meters _____meters

Eth Cable Lengthfrom IDU to

Power Injector (*)


DC Cable Length(*)


Eth Cable Type

DC Cable Type (*)Indoor power

injector interfacenumber(*)


ODUs and Mounting Type

6.14 Antennas system


(*) only for system with 2 antenna x Terminal Radio

Antennas and Polarization


ODU Assemblingmode

[ ]Directly Connected to Antenna[ ]Using Mounting Kit

[ ] Directly Connected to Antenna[ ] Using Mounting Kit

Mounting /CouplerInstallation(ifapplicable)

[ ]Integrated System[ ]Not Integrated System

[ ]Integrated System[ ]Not Integrated System

FPR Mounting KitType(if applicable)

[ ]Pole Mounting Kit[ ]Wall Mounting Kit[ ]Other

[ ]Pole Mounting Kit[ ]Wall Mounting Kit[ ]Other

WG Type [ ]Flexible W/G[ ]Standard Elliptical W/G[ ]Not Applicable

[ ]Flexible W/G[ ]Standard Elliptical W/G[ ]Not Applicable


Antenna System Station A Station B1

Type [ ]XD Type[ ]FH Type[ ]Other[ ]Integrated antenna type[ ]Not integrated antenna

[ ]XD Type[ ]FH Type[ ]Other[ ]Integrated antenna type[ ]Not integrated antenna

Diameter _____Meters _____Meters (*) _____Meters _____Meters (*)Polarization (Forsingle PolarizationSystem)

[ ]H[ ]V

[ ]H[ ]V



(*) If applicable(**) only in case of direct supplying to FPR(***) only in case of powering through Power Injector

7.1 DC Voltage Power supply on FlexiPacket Multi Radio R2.1 (Packet)

7 ODU SYSTEM CHECK AND MEASURE

To Main orsingle ODU

Station

To ProtectionODU (*)

A

To Main orsingle ODU

Station

To ProtectionODU (*)

B1

Power Supply onPS cable (**)

[ ] [ ] [ ] [ ]

Power Supply onpower injector DC

connector (***)

[ ] [ ] [ ] [ ]

P+E [ ] [ ] [ ] [ ]


(*) If applicable

7.2 Breakers / Fuse Used on FlexiPacket Multi Radio R2.1 (Packet)

Main or singleODU

Station

Protection ODU(*)

A

Main or singleODU

Station

Protection ODU(*)

B1

Breakers Type(max current

value)

_____ Amperes _____ Amperes _____ Amperes _____ Amperes



To run this test is necessary to have the remote station in TX Power OFFcondition either using the Time Tx Squelch feature or selecting Service StateRadio Port = SQUELCH (to be applied only when the remote station is managed

8.2 FlexiPacket Multi Radio R2.1 (Packet) MWR Hop Verification

8.1 FlexiPacket Multi Radio R2.1 (Packet) RF Interference Measurements

Radio Parameter Ip:


Remote NE Type(IP address)

Remote Peer NEType

Tracking No

Status Ping Ok

IP Address 10.10.10.2

NE Type FPMR(P)

System Type 1+0

LPG Group N/A

ODU Role N/A

ODU Prio N/A

Switch State N/A

Tx Power [dBm] 17

Rx Power [dBm] -96

Rx S/MSE [dB] 20

Tx Profile QPSK

8 FlexiPacket Multi Radio R2.1 (Packet) TEST RESULTS


Radio Parameter Ip:


Remote NE Type(IP address)

Remote Peer NEType

Rx Profile


Documents

Kisumu Kamau Link Acceptance DOC