Keyboards and Modules Rom# SQ8 2.2 DSS1 36 SQD8 3.0 Poly 800 M2 006 on chip DFP1 803 on chip SQD1 609 on chip -------------------------------------------------------------------------------------------------------------------- DDD-1 Initialize Powerup holding YES and NO -------------------------------------------------------------------------------------------------------------------- DS-8 / 707 Factory Data From RAM card of SYSEX (Atari Factory disk) Initialize Hold Up and Down ad powerup ROM# :DS-8= #218, 707= #905 Hold 3 and 4 and powerup -------------------------------------------------------------------------------------------------------------------- M1 (CR2032 Battery) Factory Data No ROM load From card Initialize Hold INT and Card and Combi and powerup ROM# :29 Hold INT and powerup -------------------------------------------------------------------------------------------------------------------- M1R Factory Data No ROM load Initialize Hold INT and Combi and Prog and powerup ROM# :17 Hold Int and powerup -------------------------------------------------------------------------------------------------------------------- M3R Factory Data Page 5D of Global mode ROM# :16 Hold Edit and Global and powerup Battery: CR20322(no solder) -------------------------------------------------------------------------------------------------------------------- T Series Factory Data Load from Factory disk Initialize

Hold 0 of lower keypad and Prog A and power-up then Immediately Turn Off ROM# :T-Series 28 Hold 0 of lower keypad and powerup -------------------------------------------------------------------------------------------------------------------- Wavestation / EX / AD Most recent ROM Wavestation 3.19 Wavestation EX 3.19 Wavestation A/D 1.25 Factory Data From RAM card or SYSEX (Atari factory disk) INITIALIZE: 1. Power Up / While KORG is flashing, Hold 4 & 'V' continuously until the 'Special

Screen' appears. 2. Press INIT RAM 3. Press CONT

(RAM is initialized and ROM is loaded into both RAM 1 & 2) IMPORTANT: DO NOT PRESS ANY OTHER COMMANDS ROM #: 3.19 (AD: #1.25)

1. Power Up / While KORG is flashing, Hold 4 & 'V' continuously until the 'Special Screen' appears.

2. Press CONT (IMPORTANT: DO NOT PRESS ANY OTHER COMMANDS) IMPORTANT: do not press any other commands! -------------------------------------------------------------------------------------------------------------------- Wavestation SR Factory Data No ROM load ROM# :1.15 Hold Cursor/Bank/Edit/Yes while unit is powered on January 18/93: #1.15 ----------------------------------------------------------------------------------------------------------------------- 01/W & 01/Wfd FACTORY DATA: Page 7 of GLOBAL Mode. INITIALIZE Hold RESET & COMPARE and Power Up ROM #: 64 Hold: RESET / Power Up -------------------------------------------------------------------------------------------------------------------- 03R/W FACTORY DATA: Page 05C of GLOBAL mode. ROM #:13 Hold: +1 and -1 and TURN ON Feb 7/93: #13 -------------------------------------------------------------------------------------------------------------------- X-3 & X-3R FACTORY DATA: Load from Factory disk. INITIALIZE

Hold: ENTER & Cursor DOWN and TURN ON ROM #:44 (X-2: #46) Hold: 7 & ENTER / Power Up -------------------------------------------------------------------------------------------------------------------- Product: X5/X5D/X5DR/O5RW Check ROM: Hold "+1" and "-1" while turning on. Once unit is on, let go. Init: Hold "+1" and "-1" while turning on. Once unit is on, let go. Preload: Perform preload on global screen 5. -------------------------------------------------------------------------------------------------------------------- Product: N364/N264 Check ROM: Hold "Enter and 7" while powering on. Init: Hold "Enter and 7" while powering on. Preload: Load preload disk "NFD-00P" Testmode-ENTER-8 -------------------------------------------------------------------------------------------------------------------- Product: N1/N5/N5EX/N1r Check ROM: Hold "Enter" and "1" while powering on. Init: None Preload: Press "Utility", Select "Factory Preload" and press "Enter" twice. -------------------------------------------------------------------------------------------------------------------- Product: NS5R/NX5r Check ROM: Hold "Part <" and "Param <" while powering on. Init: None Preload: Press "Enter", select "Utility". Then press "Enter" twice more.

Select "Factory Preset" and press "Enter". Select "yes" and Press "Enter" once more.

-------------------------------------------------------------------------------------------------------------------- Product: Trinity Series Keyboards Check ROM: Turn on, look at screen (o.s. 3.1.2 all models, 2.4.1 for Solo) Init: Hold "Enter" and "0" while powering on. Preload: Load preload disk "TFD-00P" -------------------------------------------------------------------------------------------------------------------- Product: TR-Rack Check ROM: Hold "Edit" and ">" while powering on, o.s 1.0.4 Init: Hold "Edit" and "A4" while powering on. Preload: Global mode screen 10 -------------------------------------------------------------------------------------------------------------------- Product: Prophecy Check ROM: Hold "Wheel 3" button while powering on. Init: None Preload: Shut off protects on Global screen 20, Preload "All_Data" on Global screen 19 -------------------------------------------------------------------------------------------------------------------- Product: Z1/Z1EX Check ROM: Hold Enter and 8 while powering on. Init: Hold SW1 and SW2 while powering on. Preload: Enter Global Mode, Screen: "Global Data Utility". Select "Factory" and press Enter twice" --------------------------------------------------------------------------------------------------------------------

Product: SG-ProX Check ROM: Hold "Program" and "Piano 1" while powering on. Init: Hold "Program" and "Piano 1" while powering on. Preload: Turn off protects for program and performance in Global mode

screens 12 and 13, then perform preload on Global mode screen 14.

(Service Note: if problem symptom is Damper pedal controld Modulation Wheel fucntion…reason is mod wheel harness came unpluged from PCB)

-------------------------------------------------------------------------------------------------------------------- Product: SG-Rack Check ROM: Hold "Edit" and "A4" while powering on. Init: Hold "Edit" and "A4" while powering on. Preload: Turn off protects for program and performance in Global mode

screen 6, then perform preload on Global mode screen 7 -------------------------------------------------------------------------------------------------------------------- Product: Triton, Triton Rack and Karma Check O.S On Screen Init: Enter and 0 while powering up Preload: On disk supplied O.S Triton 2.1.0, Triton Rack 1.1.0, Karma 1.0.2 -------------------------------------------------------------------------------------------------------------------- Product: MS2000(R) Check O.S. Power on while holding 5 and Mod Sequence ON/OFF Current o.s. 1.0.5 Load O.S PC installer program, need MIDI interface and cables.

Turn on MS2000 while holding WRITE and TYPE PreLoad In Global -------------------------------------------------------------------------------------------------------------------- i-Series I-1 FACTORY DATA Load from Factory disk. INITIALIZE Hold: PROGRAM & DISK and TURN ON ROM VERSION: Hold EDIT STYLE and Power UP Check ROM: Hold "Arr. Play" and "Global" powering on. Init: Hold "Arr. Play" and "Global" powering on. Preload: Load preload disk "IFD-01P" -------------------------------------------------------------------------------------------------------------------- I-2 & I-3 FACTORY DATA: Load from Factory disk. INITIALIZE: Hold: ARR PLAY and EDIT STYLE and TURN ON ROM #:25 (#58 with upgrade) Hold: EDIT STYLE & EDIT PROGRAM and TURN ON

Product: iX300, i2, i3 Check ROM: Hold "Arr. Play" and "Global" powering on. Init: Hold "Arr. Play" and "Global" powering on. Preload: Load preload disk "IFD-00P" -------------------------------------------------------------------------------------------------------------------- Product: i4s Check ROM: Hold "Arr. Play" and "Program" powering on. Init: Hold "Arr. Play" and "Program" powering on. Preload: Load preload disk "IFD-00P" -------------------------------------------------------------------------------------------------------------------- Product: i5S/I5M Check ROM: Hold "Arr. Play" and "Global" while powering on. Init: Hold "Arr. Play" and "Global" while powering on. Preload: Load preload disk "IFD-00P" -------------------------------------------------------------------------------------------------------------------- Product: I30 Check ROM: Turn on, look at top left side of screen (If version is 1.0 no number will appear.) Init: Hold "Arrange Play" and "Global" while powering on. Preload: Load preload disk "i30FD-00P" -------------------------------------------------------------------------------------------------------------------- Product: iS40/50/i40M Check ROM: Hold "Arr. Play" and "Global" powering on. Init: Hold "Arr. Play" and "Global" powering on. Preload: Load preload disk "FDD-1004" -------------------------------------------------------------------------------------------------------------------- Product: Pa80 Check O.S On start-up screen, currently version 2.0 Preload Go to Disk Mode, Utilities, Restore Data. Make preload data from

five files available from the Pa80 site. -------------------------------------------------------------------------------------------------------------------- IH Initialize POWERUP W/ Detune & Bass -------------------------------------------------------------------------------------------------------------------- C-Series C-505 INITIALIZE MIDI/TRANSPOSE & SPLIT and RESTART UNIT -------------------------------------------------------------------------------------------------------------------- Effect Processors A1 Factory Data ROM card included in original packaging Initialize

Hold Write and –1 and powerup ROM# :A1 #18 on chip or 901718 Hold Write and powerup -------------------------------------------------------------------------------------------------------------------- A3 / A2 Factory Data Initialize 1. Hold Down arrow and Up arrow and powerup 2. Press "E" (Yes) ROM#: A3=881012,A2=90316 1. Hold Utility and Up arrow and A and powerup 2. While screen displays "How do you do?" press F 3. Press A to change M/R to M/S 4. Press D to change D/R to D/S 5. Press F (Exit) 6. Press Utility then F (Version No. shown very briefly 7. Press F (Exit) -------------------------------------------------------------------------------------------------------------------- A-4 INITIALIZE Hold "WRITE" & "BYPASS" and Power On -------------------------------------------------------------------------------------------------------------------- Product: PX1 Check ROM: None Init: None Preload: Hold down "Metronome" and "Enter" buttons while powering on,

then let go and press "+" button. -------------------------------------------------------------------------------------------------------------------- Product: PX2 Check ROM: None Init: None Preload: Hold down "Rhythm" and "Enter" buttons while powering on, then

let go and press "+" button. -------------------------------------------------------------------------------------------------------------------- Product: AX1G/B Check ROM: None Init: None Preload: Hold down "Value +" and "Page >" buttons while powering on,

then let go and press "Value +" again. -------------------------------------------------------------------------------------------------------------------- Product: AX30B/G, AX300B/G Check ROM: None Init: None Preload: Hold "Param/Value" and "Compare/Write" while powering on, then

let go and press "Compare/Write" again. -------------------------------------------------------------------------------------------------------------------- Product: G1/2/3/4/5 Check ROM: None Init: None Preload: Hold down the Bank Pedal and "Compare/Write" buttons

while powering up, then let go and press "Compare/Write" again. -------------------------------------------------------------------------------------------------------------------- Product: 411FX, 104DS, 105OD, 301DL Check ROM: None Init: None Preload: Hold down the Program button while powering up, then Let go and press again. -------------------------------------------------------------------------------------------------------------------- Product: DL8000-R Check ROM: Hold "ms/d" and "HOLD" while powering up. Init: Hold "ms/d" and "HOLD" while powering up. Preload: Hold "ms/d" and "HOLD" while powering up. Wait

for "EEP Testing" to come up on the screen, then shut unit off and power back on.

-------------------------------------------------------------------------------------------------------------------- Product: AM8000-R Check ROM: Hold "FX1" and "FX2" while powering up. Init: Hold "FX1" and "FX2" while powering up. Preload: Hold "FX1" and "FX2" while powering up. Wait

for "EEP Testing" to come up on the screen, then shut unit off and power back on.

--------------------------------------------------------------------------------------------------------------------

Digital Recording Devices Product: D8 Check ROM: Hold "Metronome" and "Record Select" button # "6" while

powering on the unit. Init: None Preload: None -------------------------------------------------------------------------------------------------------------------- 168RC INITIALIZE: Left knob under screen and + and – -------------------------------------------------------------------------------------------------------------------- D12/D16/D1600 Check O.S On Start-up Screen O.S. update Loaded from external media, go to system, choose external drive letter, choose option load system O.S. D16 2.0.1, D1600 -------------------------------------------------------------------------------------------------------------------- Dance Tools KAOSS PAD INIT HOLD + FX ON/OFF + 3 + POWER ON After "L" is indicated, press 1->3->5->1->3->5 in order --------------------------------------------------------------------------------------------------------------------

Electribe A/R � How to start and operate the test mode �+TAP+PowerON � Start the test mode � �ITEM UP � �ITEM DOWN 16 �STEP UP 15 �STEP DOWN �How to reset the system TRANSPOSE+WRITE & PLAY � EA-1 PRELOAD SOLO+WRITE & PLAY � ER-1 PRELOAD Electribe-S Must have a Smart Media Reader/Writer and a Smart Media card to do a product upgrade. Copy o.s to smart media card. Put Smart Media card into ES1 and power on holding SAMPLE and GLOBAL. When the display indicates end, power down. Check O.S. Power on holding RECORD and STOP, current o.s. 1.04 -------------------------------------------------------------------------------------------------------------------- Other: Johnson Millennium Amplifier INITIALIZE Powerup W/CONFIG button * onscreen Let go Push MOD V1.05 most recent -------------------------------------------------------------------------------------------------------------------- Johnson JM-60 Hold “american model” button Powerup Keep holding until LED has 2 lines Then hold “british model” button Until PR on screen Let go -------------------------------------------------------------------------------------------------------------------- Product: JMP-1 Check ROM: None Init: None Preload: Hold "OD1" and "Clean1" while powering up. -------------------------------------------------------------------------------------------------------------------- Product: JFX1 Check ROM: None Init: None Preload: Hold down arrow button and "Store" while powering on. -------------------------------------------------------------------------------------------------------------------- S3 Poweron w/ STOP + S1