Upload
others
View
10
Download
0
Embed Size (px)
Citation preview
12-‐10-‐13
1
12-10-09 KEMA Coatings Limited Cad Weld Coating System Procedures 1
The KEMA COATINGS LIMITED CAD WELD COATING PROCEDURE USING KEMA 250 SEALANT, KEMA 250-12 TOP
COAT AND RECOMMENDED LIQUID PRIMER
The specification describes the technical requirements for coating thermite weld (cad weld) connections that are used to deliver cathodic protection to buried steel pipelines worldwide. SCOPE: This specification shall be used by pipeline employees and all prime sub contractors employed by it. The specification shall be used on all activities related to cathodic protection worldwide. BRIEF DESCRIPTION OF CHANGES: This specification is revised to take into consideration the use of one, two and three wire cad weld installations worldwide.
12-10-09 KEMA Coatings Limited Cad Weld Coating System Procedures 2
The KEMA COATINGS LIMITED CAD WELD COATING PROCEDURE USING KEMA 250 SEALANT, KEMA 250-12 TOP
COAT AND RECOMMENDED LIQUID PRIMER
SAFETY: 1. The Contractor shall maintain copies of the Material Safety Data
Sheets (MSDS) for all controlled substances and he shall ensure that employees are familiar with the precautions of the MSDS regarding hazards, necessary protective equipment, first aid measures and be trained in the handling and the use of these products.
2. Work gloves and safety glasses shall be worn when handling the liquid primer.
3. Protection from inhalation is required. The primer shall only be used in a well ventilated are. Personnel shall wear appropriate respiratory protection in areas where vapours may accumulate.
4. No open flames, smoking or welding shall be permitted in the immediate vicinity of open containers of liquid primer at all times.
5. Liquid primer containers shall not be left open in an effort to avoid contaminating the coating. Only authorised personnel shall be permitted to handle the liquid primer.
12-‐10-‐13
2
12-10-09 KEMA Coatings Limited Cad Weld Coating System Procedures 3
The KEMA COATINGS LIMITED CAD WELD COATING PROCEDURE USING KEMA 250 SEALANT, KEMA 250-12 TOP
COAT AND RECOMMENDED LIQUID PRIMER
APPROVED MATERIALS: Coating Component: Approved Coating: Approved Manufacturer: Sealant KEMA 250 – 4” KEMA Coatings Limited (K250) p/n 752 GHA 760 Top Coat KEMA 250-12 – 4” KEMA Coatings Limited (K250-12) p/n 752 GHA 1760 Primer KEMA Recommended Contact KEMA Coatings NOTE* Liquid epoxy coatings shall NOT be used to prime thermite welds. Dissimilar thermite welding mixtures and wire movement can cause epoxy coatings to fail at these installations then lead to dry film holidays.
12-10-09 KEMA Coatings Limited Cad Weld Coating System Procedures 4
The KEMA COATINGS LIMITED CAD WELD COATING PROCEDURE USING KEMA 250 SEALANT, KEMA 250-12 TOP
COAT AND RECOMMENDED LIQUID PRIMER
STORAGE AND MIXING: Liquid primer shall be stored in well sealed containers at temperatures between 5C.-30C. (40F.-85F.). Maintain sealant, top coat and primer at temperatures between 15C.-30C. (60F.-85F.) for at least 12 hours immediately before use. Keep all products within this temperature range during application whenever possible. Make certain that the primer has not gone beyond its expiry date before use and if it has replace with a current dated container. Mix primer before every application. SURFACE PREPARATION: A minimum SSPC-Sp-11-87T (Power Tool Clean to Bare Metal) in combination with SSPC-SP-2 (Solvent Clean) assisted by a metal file where necessary shall be completed before application of liquid primer. DO NOT BUFF OR POLISH BARE METAL SURFACES. A minimum SSPC-SP-1 (Hand Tool Clean) in combination with SSPC-SP-2 shall be completed before application of liquid primer when no power source is available.
12-‐10-‐13
3
12-10-09 KEMA Coatings Limited Cad Weld Coating System Procedures 5
The KEMA COATINGS LIMITED CAD WELD COATING PROCEDURE USING KEMA 250 SEALANT, KEMA 250-12 TOP COAT AND RECOMMENDED LIQUID
PRIMER
LIQUID PRIMER APPLICATION: 1. Open lid of primer container. 2. Use stir stick or power mixing blade on slow rotation to mix primer. 3. The primer shall be mixed thoroughly before every application. This can be
verified visually when the mixed primer exhibits a deep black colour from top to bottom of the container.
4. A short bristle brush shall be used to apply the primer. 5. The Applicator shall make every effort to apply the primer in a neat square
or rectangular shape upon the surface of the clean pipe.
6. The primer shall be applied using a left to right motion followed by a top to bottom motion until entire surface to be coated (including individual wires) is covered.
7. Before priming Applicator shall carefully bend the welded wires up and away from the pipe surface to allow brush into all areas needing coating.
8. Applicator shall not permit any pooling or icycling (drips) of the primer before coating with sealant.
9. Primer must be DRY TO THE TOUCH before sealant shall be applied.
12-10-09 KEMA Coatings Limited Cad Weld Coating System Procedures 6
12-‐10-‐13
4
12-10-09 KEMA Coatings Limited Cad Weld Coating System Procedures 7
12-10-09 KEMA Coatings Limited Cad Weld Coating System Procedures 8
12-‐10-‐13
5
12-10-09 KEMA Coatings Limited Cad Weld Coating System Procedures 9
12-10-09 KEMA Coatings Limited Cad Weld Coating System Procedures 10
12-‐10-‐13
6
2
12-10-09 KEMA Coatings Limited Cad Weld Coating System Procedures 11
12-10-09 KEMA Coatings Limited Cad Weld Coating System Procedures 12
12-‐10-‐13
7
1
2
3
12-10-09 KEMA Coatings Limited Cad Weld Coating System Procedures 13
12-10-09 KEMA Coatings Limited Cad Weld Coating System Procedures 14
12-‐10-‐13
8
12-10-09 KEMA Coatings Limited Cad Weld Coating System Procedures 15
12-10-09 KEMA Coatings Limited Cad Weld Coating System Procedures 16
12-‐10-‐13
9
12-10-09 KEMA Coatings Limited Cad Weld Coating System Procedures 17
12-10-09 KEMA Coatings Limited Cad Weld Coating System Procedures 18
12-‐10-‐13
10
12-10-09 KEMA Coatings Limited Cad Weld Coating System Procedures 19
12-10-09 KEMA Coatings Limited Cad Weld Coating System Procedures 20
12-‐10-‐13
11
12-10-09 KEMA Coatings Limited Cad Weld Coating System Procedures 21
12-10-09 KEMA Coatings Limited Cad Weld Coating System Procedures 22
12-‐10-‐13
12
12-10-09 KEMA Coatings Limited Cad Weld Coating System Procedures 23
12-10-09 KEMA Coatings Limited Cad Weld Coating System Procedures 24
12-‐10-‐13
13
12-10-09 KEMA Coatings Limited Cad Weld Coating System Procedures 25
12-10-09 KEMA Coatings Limited Cad Weld Coating System Procedures 26
12-‐10-‐13
14
12-10-09 KEMA Coatings Limited Cad Weld Coating System Procedures 27
12-10-09 KEMA Coatings Limited Cad Weld Coating System Procedures 28
12-‐10-‐13
15
12-10-09 KEMA Coatings Limited Cad Weld Coating System Procedures 29
12-10-09 KEMA Coatings Limited Cad Weld Coating System Procedures 30
12-‐10-‐13
16
12-10-09 KEMA Coatings Limited Cad Weld Coating System Procedures 31
12-10-09 KEMA Coatings Limited Cad Weld Coating System Procedures 32
KEMA COATINGS LIMITED""
Address:"Unit 904, 60 Wyndham Street South"Guelph, Ontario, CANADA, N1E 7H7"
"Telephone: "
Local: 519.826.9374"Toll Free: 1.888.733.5362"
"Email:"
[email protected]"[email protected]"
"Fax: 519.826.9374"
"SKYPE: kema.mark"
""