KEL-TEC PLR-16 Pistol

SAFETY, INSTRUCTION & PARTS MANUAL

STATEMENT OF LIABILITYThis pistol may be classified as a dangerousweapon and is surrendered by KEL-TEC CNCINDUSTRIES INC. with the understanding thatthe purchaser assumes all liability resultingfrom unsafe handling or any action thatconstitutes a violation of any applicable lawsor regulations. Firearms can cause seriousinjury and death. Safety must be the primeconsideration of anyone who handlesfirearms. Always treat a firearm as though itwere loaded. Always keep the muzzle pointedin a safe direction.In owning a firearm, you are responsible forthe firearm’s safety and security. Alwayssecure firearms from children.

READ THESE INSTRUCTIONS ANDWARNINGS CAREFULLY, BE SURE YOUUNDERSTAND THESE INSTRUCTIONSAND WARNINGS BEFORE USING THISFIREARM.

This SAFETY, INSTRUCTION & PARTS MANUALshould always accompany this firearm and betransferred with it upon change of ownershipor when the firearm is loaned or presented toanother person. A copy of the SAFETY,INSTRUCTION & PARTS MANUAL is availableFREE upon request and can also be down-loaded from the internet at:http://www.Kel-Tec.com.

REV:0605

SAFE GUN HANDLING IS YOUR RESPON-SIBILITY

The PLR-16 pistol is designed and chamberedfor the 5.56mm NATO (.223 Remington)cartridge. The type of ammunition is also statedon the right side of the receiver. Do not useany other ammunition.

Only use commercially manufactured ammuni-tion, clean, dry, and in good condition. Neveruse non-standard, reloaded or damagedcartridges.

Never use ammunition where the pressurelevels exceed industry standards. Kel-Tecguns are manufactured from high qualitymaterials. They will provide extended servicelife. However, all warranties, expressed orimplied, are voided and Kel-Tec will not be liablefor property damage or personal injury andconsequential damages, if faulty ammunition isused in Kel-Tec centerfire firearms.

Discharging firearms in poorly ventilated areas,cleaning firearms, or handling ammunition mayresult in exposure to lead and other sub-stances known to cause birth defects,reproductive harm, and other serious physicalinjury. Have adequate ventilation at all times.Wash hands thoroughly after exposure.

Never discharge a firearm without propershooting glasses and ear protection. Nevershoot at any water surface or any surfacewhere a ricochet can occur.

Never shoot until you are sure of yourbackstop and what lies beyond it.

If the gun does not discharge after pulling thetrigger, do not change its direction for at least30 seconds, you could be having a “hangfire”.

Do not allow a firearm to be used by individualswho do not understand its safe operation andthe rules of safe gun handling.

CAUTION: After firing several rounds theforward, exterior metal parts of the PLR-16pistol get hot and can cause severe burns.

Be sure all accessories are compatible withthe firearm and that the accessories do notinterfere with safe operation.

When transporting your firearm, be sure yourfirearm is unloaded.

If you do not understand how to operate anyof our products or have any questions abouttheir safe handling, please write, call, or emailus.

Always be aware of other people so that theycannot accidentally walk into the line of fire.When firing on a target range, be alert andfollow the range officer’s commands. Nevercross obstacles such as fences or streamswith a loaded firearm.

READ AND CAREFULLY FOLLOW THESEWARNINGS AND INSTRUCTIONS

These warnings and instructions are providedto assure the safe functioning of the pistol.Failure to heed them may result in improperfunctioning and serious injury.

Kel-Tec firearms are designed to functionreliably with proper care and knowledgeableuse. Do not use your firearm unless you fullyunderstand these instructions, and the safeoperation of your firearm.

Only safe gun-handling habits will ensure thesafe use of your firearm. This is yourresponsibility. Accidents are the result ofviolating the rules of safe gun handling andcommon sense.

Before handling a firearm, understand itsoperation.

Never accept or pick up a firearm withoutchecking the magazine and the chamber toassure the weapon is empty. Do not trust theextractor to clear the chamber, look and feel.

Always make sure the muzzle is pointed in asafe direction at all times.

Never point a firearm at anyone or anythingyou do not intend to shoot.

Make sure your “audience” is always 5 feetbehind you, not next to you when firing.

Keep your firearm unloaded when not in use.

Never keep a loaded firearm in the home orvehicle. Never store a firearm with a cartridgein the chamber.

Never store firearms and ammunition together,keep them locked up and away from children.

Never touch the trigger when working theaction. Never alter any components of yourfirearm.

Never take medications, drugs, or alcoholwhen handling firearms.

Never load or unload a firearm withoutassuring the muzzle is pointed in a safedirection.

Never load a firearm except immediately beforeshooting.

WARNING: DO NOT ATTEMPT TO RE-MOVE A LODGED BULLET OR ANYOTHER OBSTRUCTION BY USING ABLANK CARTRIDGE, OR A CARTRIDGEWITH THE BULLET REMOVED, OR BYANY MEANS OTHER THAN THE USE OFTHE PROPER SIZE CLEANING ROD(WITHOUT A TIP OR BRUSH) ANDREASONABLE FORCE APPLIED TO THEROD. BE CERTAIN ALL LOOSE POWDERHAS BEEN REMOVED FROM THE BOREAND ACTION BEFORE INTRODUCING THEROD INTO THE BORE.

Failure to Feed: This occurs when acartridge has been fed from a magazine butnot fully chambered. If this occurs, keep thefirearm pointed in a safe direction, remove thatcartridge, operate the bolt manually andcontinue shooting. If necessary, change themagazine. The most common causes are dirt orforeign objects impeding the magazinefollower. Improperly crimped cartridges areanother cause.

Failure to Eject or Extract: A fired case is notfully extracted from the chamber or ejectedfrom the pistol. Again, keep the firearm pointedin a safe direction, clear the gun by operatingthe bolt, remove the case and continue. Ifnecessary, change the magazine. The mostcommon causes are a damaged extractor,ejector, or ammunition. Improperly loaded orsized cartridges can also cause this. If any ofthe above problems are not solved by cleaning

or by use of other brands of ammunition, stopfiring, unload and return the PLR-16 pistol toour service department.

FiringWith the muzzle pointed in a safe direction andyour finger outside the trigger guard, take aimat a safe target, disengage the safety andsqueeze the trigger until a round is fired.Release the trigger and you are ready to fireanother round. Upon firing, the bolt movesrearward extracting and ejecting the firedround and returns to the forward positionfeeding another round automatically. Thissequence can be repeated until the last roundhas been fired. The PLR-16 has an automaticbolt stop so after the last round is fired the boltwill lock open. Remove the empty magazine bypressing the magazine catch located on theright side of the receiver and pull out the emptymagazine. To continue shooting simply insert afull magazine into the magazine well, firmlypush it up until it locks. Pull back and releasethe operating handle to release the bolt stopand feed the next round. The rifle is now readyto fire.

UnloadingTo unload the PLR-16 pistol, engage the safety,push in the magazine catch, remove themagazine, and pull the operating handle fullyback to eject the round in the chamber. Do notobstruct the ejector port and keep fingersaway from trigger and muzzle. With theoperating handle fully held back push up on the

INTRODUCTIONThe PLR-16 is a semi-automatic pistol cham-bered for the 5.56mm NATO (.223 Remington)cartridge. The PLR-16 pistol will accept moststandard M-16 type magazines.

CONSTRUCTIONThe receiver and grip are made of an impactresistant glass reinforced Zytel. The receiverhas an aluminum insert molded into the front toaccept the barrel and the serial number. AMIL-STD-1913 picatinny rail is integrated intothe top of the receiver to allow for attach-ments.

The firing mechanism is of conventional singleaction type. It has a push bolt safety thatblocks the trigger. The muzzle end of the barrelis threaded with a 1/2-28 inch thread to acceptstandard attachments such as a muzzle brake.With the pistol unloaded, chamber clear, andsafety on, simply unscrew the knurled threadprotector to expose the thread. Apply no morethan 20 ft-lbs of torque to these threads.

INSTRUCTIONS FOR USE

SafetyTo achieve operator safety, combined withease of handling, the PLR-16 pistol’s manualsafety, when applied, positively blocks thetrigger from rotating the sear. The safety canbe applied at any time, whether the hammer iscocked or not. Only when the red ring on thesafety is fully obscured is the safety engaged.Obviously the safest condition of the pistol isunloaded. Also considering unauthorizedoperation, other modes of storing or carryingwill gradually improve readiness at the cost ofsafety.

MalfunctioningProper function of your PLR-16 pistol is directlyrelated to maintenance and care, and to theammunition you use. Some of the morecommon types of malfunctions which mayoccur are as follows:

Misfire: A failure to fire or an unusual soundupon firing is always a signal to cease firingand immediately examine the bore of thefirearm. It is not sufficient to just pull theoperating handle back and examine thechamber. You must remove the magazine, clearthe chamber, lock the bolt open and inspect thebore visually - and with a rod if necessary - tobe certain it is completely clear of anyobstruction. Failure to detect and remove abore obstruction can result in serious injury ordeath to the shooter and bystanders, as wellas damage to the firearm.

bolt stop and slowly release the operatinghandle, the bolt should stay open. Visuallyinspect the chamber to make sure it is empty.Pull back on the operating handle to release thebolt stop and release the operating handle toclose the chamber. Push the remainingcartridges in the magazine forward and out.

LoadingTo load, fill the magazine by pressing acartridge downward on the magazine follower(or downward on the previously loadedcartridge). Continue loading until you haveloaded the number of cartridges you wish toload, up to the magazine capacity of 10rounds. Do not attempt to load your magazinewith more than the specified number ofrounds. Doing so can damage the magazineand can cause a feeding malfunction. Beforeinserting a loaded magazine always tap theback of the magazine against a hard surfacetwo or three times in order to properly seat allthe cartridges to the rear of the magazine.

With the pistol’s safety engaged, hold the pistolin one hand with the muzzle pointing in a safedirection and with your finger off the triggerand outside the trigger guard. Insert the loadedmagazine into the grip until it is locked in place.Check to assure that the magazine is secure.Pull the operating handle back and release.This strips a round from the magazine andseats it in the barrel chamber.

If you wish to restore the magazine in yourpistol to full capacity, press the magazine catchand remove the magazine to load the missinground. Remember to keep the safety engagedand your pistol pointed in a safe directionunder all conditions and always keep yourfinger off the trigger and outside the triggerguard until ready to fire.

DISASSEMBLYNOTE: Disassembly can be performed withonly a cartridge but a few simple tools such asa small punch and small pliers can make thingsmuch easier. A Phillips head screw driver is notnecessary for general maintenance and noneof the screws on the pistol should ever needto be removed for general maintenance.

Pistol disassemblyRemove the magazine and unload your PLR-16pistol. Cycle the operating handle to be surethat there is no round in the chamber. Makesure the bolt is in the forward position and thesafety is engaged.

Bolt carrier disassembly:To remove the bolt, cam pin, and firing pin,simply press out the firing pin pin from the rightside of the bolt carrier with a small tool or acartridge. Remove the firing pin from the backof the bolt carrier, you may need to tap the boltcarrier or move the bolt in and out to get thefiring pin to fall out enough to grip it. With thefiring pin removed the cam pin can now bepulled out and with the cam pin out the bolt canbe removed from the front of the carrier.To remove the piston head, recoil spring tube,and recoil spring, first rotate the recoil springtube to align the holes in the recoil spring tubewith the pin in the piston head. While holdingthe piston head with one hand, press out thepiston pin with the firing pin or a small tool.

CAUTION: The piston head is underpressure from the compressed recoilspring and the piston head and recoilspring can easily fly out and injureyourself or bystanders, always keep ahand on the piston head and point thepiston head in a safe direction whenremoving it.

With the piston pin removed the piston head isnow free to be taken off. Slide the recoil springtube off the piston rod and remove the recoilspring from the recoil spring tube.

CAUTION: Some accessories that aremounted to the picatinny rail on the topof the receiver may interfere with thedisassembly of the PLR-16 pistol. It isadvisable to remove any scopes or otherdevices mounted to the rail beforeproceeding with disassembly.

With a cartridge or other pointed objec,t pushout and remove the assembly pin. Rotate thegrip down and forward. Grab the recoil spring

tube, pull it towards the muzzle and twist it 1/4turn so that the locking tab points towards thetop of the pistol, it should slide into the receiverabout 1/4 inch as you release the recoil springtube. Slowly pull back on the operating handle,the recoil spring tube should also move backand there should not be any spring pressurefelt. Pull the handle all the way back and push itdown into the operating handle removal cutoutin the receiver. The operating handle shouldnow be able to be pulled straight out of the boltcarrier. After the operating handle is removedthe bolt carrier assembly can now be guidedout of the bottom of the receiver.

PLR-16PISTOL

Part# 522 Exchange Only

504

522

533

575

512

514

104

108

110 112

114

116

118

120

122

126

128

130

134

140

142

144

145

146

150

150

150

150

154

154

158

176

178

180

182

186

190

194

196

198

203

204

205

207208

210

216

228

234

252

254

256

258

274

276

276

276

276

276

276

276

276

276

276

276

276

276276

278

278

278278

280

282

284294

296

298

299

355357

366

367

367

384

538

438

524

501

502

104 BARREL EXTENSION108 BARREL RETAINER110 BOLT112 EXTRACTOR114 EXTRACTOR AXIS116 EJECTOR118 FIRING PIN120 BOLT CARRIER122 OPERATING HANDLE126 CAM PIN128 RECOIL SPRING

CATCH130 PISTON HEAD134 FIRING PIN PIN140 TRIGGER BLOCK142 HAMMER144 SEAR145 SEAR SPRING PIN146 SAFETY150 STOCK SPACER-16154 SPACER-29158 ASSEMBLY PIN176 MAG CATCH SPRING178 HAMMER SPRING180 SEAR SPRING182 TRIGGER SPRING186 STOCK PIN SPRING

190 BOLT STOP SPRING194 EXTRACTOR SPRING196 EJECTOR SPRING198 MAGAZINE SPRING203 DRIVER HOUSING204 MAGWELL205 PHILLIPS DRIVER207 RED O'RING208 TRIGGER210 EXTRACTOR SPRING

BUFFER216 RECEIVER

SPREADER228 BOLT STOP234 MAG CATCH252 MAGAZINE HOUSING254 MAGAZINE

FOLLOWER256 MAGAZINE PLATE258 MAGAZINE BOTTOM274 EJECTOR PIN276 RECEIVER SCREW278 RECEIVER WASHER280 SEAR PIN282 HAMMER AXIS284 BARREL EXTENSION

PIN

294 O'RING296 PISTON PIN298 TRIGGER AXIS299 GAS BLOCK PIN355 FRONT SIGHT POST357 FRONT SIGHT

DETENT PIN366 REAR OPEN SIGHT367 REAR SIGHT

ADJUSTER384 FRONT SIGHT

DETENT PIN SPRING438 C-GAS HEAD501 BARREL502 COMPACT FOREND

BARREL NUT504 LONG THREAD

PROTECTOR512 PISTOL GRIP RIGHT514 PISTOL GRIP LEFT522 PISTOL RECEIVER524 D PISTON ROD533 PISTOL RECOIL

SPRING TUBE538 PISTOL GAS BLOCK

FRONT SIGHT575 PISTOL RECOIL

SPRING

310-MAGAZINE ASSEMBLY

carrier. Push the bolt assembly into the carrieras far as it will go and then insert the firing pininto the back of the bolt carrier, being sure thehalf moon shaped cut is facing up. If it does notgo in all the way, the cam pin or the bolt maynot be inserted correctly. Insert the firing pinpin into the bolt carrier from the left side. DONOT FORCE THE FIRING PIN PIN. If it does notgo in easily check that the firing pin is installedcorrectly. Check the operation of the bolt andfiring pin to be sure that they move freely.

Pistol assemblyWith the grip folded, rest the pistol on its leftside. Take the bolt carrier assembly, pull the

bolt out as far as it will go and twist the recoilspring tube so that the lock tab is at the top ofthe bolt carrier. Insert the carrier from the rearof the receiver, be sure not to twist the bolttube or push in the bolt as you insert it. Alignthe operating handle hole in the carrier with thecut-out in the receiver and insert the operatinghandle. Push the carrier up slightly so that theoperating handle aligns with the slot for it andthe recoil spring tube is parallel with the barrelof the pistol.

NOTE: It is not recommended that youdisassemble the grip of the PLR-16pistol; the hammer spring is constantlyunder tension and can easily injure youor others.

ASSEMBLY

Bolt carrier assembly:To install the piston head, recoil spring tube,and recoil spring, insert the recoil spring intothe recoil spring tube. Slide the recoil springtube with recoil spring onto the piston rod.Align the holes in the recoil spring tube with thehole in the piston rod. Push the piston head

onto the recoil spring and onto the piston rod.Insert the firing pin or similar tool into the pistonhead hole to temporarily hold the piston head inplace. While slowly pulling out the firing pin,push in the piston pin from the other side until itis flush with the piston head. Twist the recoilspring tube so that the locking tab pointstowards the top of the bolt carrier. Check theoperation of the recoil spring by lightly pullingon the recoil spring tube to compress thespring.

To install the bolt, cam pin, firing pin, and firingpin pin, insert the bolt into the front of the boltcarrier. Twist the bolt so that the extractor ison the right side of the carrier and the cam pinhole in the bolt lines up with the cam pin slot inthe bolt carrier. Insert the cam pin into the holein the bolt, be sure that the tab on the cam pinis pointing straight out the left side of the bolt

turn and tighten (clockwise) the left screw 1/8turn.

For the front sight, use a small tipped tool, like apaper clip or an M-16 A2 style front sight tool(not included) to depress the detent pin andturn the sight post by hand. One click (1/4 turn)will change the point of impact 2inches at 100yards. Clockwise moves the point of impact upand counter-clockwise moves it down.

MAINTENANCE

Your pistol is a precision instrument and toinsure reliable function, it is necessary tofollow a routine maintenance procedure. Afterfiring your pistol, be sure to unload it followingthe procedure outlined in the section entitled“Unloading” before any cleaning or mainte-nance procedure.

Routine cleaning, after every shootingsession:Your pistol should be cleaned by brushing thebarrel bore and chamber with a good powder-removing solvent and bore brush. Wipe theareas clean with patches or a swab. Using asmall brush dipped in solvent, remove alldeposits from around the breech of the barrel,and chamber, extractor and adjacent areaswhich have been subjected to the action ofpowder or primer residue. Remove any residueon the frame with light brushing and a solvent.After cleaning the entire gun, use a cloth toapply a light coating of high quality gun oil to allexternal surfaces and wipe clean.

Additional cleaning, after firing 500rounds:Remove the bolt carrier assembly and fullydisassemble it as stated in the disassemblysection of this manual. Thoroughly clean withsolvent and a brush the piston head, piston pin,piston rod, recoil spring, recoil spring tube, bolt,cam pin, firing pin, and bolt carrier. Do not clean

WARNING: If the recoil spring tube is notparallel with the barrel of the pistol thebolt carrier assembly is not installedcorrectly. Remove the carrier assemblyand install it again paying close attentionto the alignment of the lock tab on therecoil spring tube as you insert thecarrier and also be sure that the boltitself is always in the forward mostposition as you insert the carrierassembly into the receiver.

Push the operating handle all the way forward,be sure that the piston head lines up and goesinto the gas head. Grip the recoil spring tube,pull it forward and twist it 1/4 turn so that thelocking tab on the recoil spring tube goes intothe receptacle on the left side of the receiver.Pull the operating handle back and forth tocheck that it moves freely, if it does not, takeout the bolt carrier and check to make sureeverything is installed correctly and nothing isdamaged. Unfold the grip. Insert the assemblypin into the hole and press it in until it is flushwith the outside of the grip.

SIGHT ADJUSTMENT

Sight Adjustment on the PLR-16 Pistol dependson the placement of the rear sight. If the sightis in the farthest forward slot on the picatinnyrail, the pistol will have a different sight radiusthan if the sight is placed farthest rearward onthe picatinny rail. The data given is for the sightin the rearmost position. Use the includedPhillips screwdriver to adjust the windage withthe two screws on the sides of the rear sight.Tighten the screw on the same side of the rearsight that you want to move the point of impactto. You may have to loosen the opposite sidescrew a little. For example: to move the pointof impact left 1 inch at 100 yards you wouldloosen (counter-clockwise) the right screw 1/8

WARRANTY

This warranty is granted by Kel-Tec CNCIndustries, Inc. P.O. Box 236009, Cocoa, FL32923. This lifetime warranty is effective fromthe date of purchase and applies to the originalowner of a Kel-Tec PLR-16 pistol.

Kel-Tec firearms are warranted to be free fromdefects in material and workmanship. Anysuch defects of which Kel-Tec receiveswritten notice by the original owner, will beremedied by Kel-Tec without charge within areasonable time after such notification anddelivery of the product as provided below.

Warranty claims (in writing) and the gunconcerned should be delivered (transportationcharges pre-paid) to:

Kel-Tec CNC, IncService Department1475 Cox RoadCocoa, FL 32926.

No return authorization number is required. Inaddition, a copy of a bill of sale in the owner’sname, or a copy of ATF Form 4473, indicatingdate of purchase must be included.

In order to expedite service, warranty claimsshould state the model and serial number of thegun concerned and a description of thedifficulty experienced. It is recommended thatshipments be insured by the owner, since Kel-Tec will accept no responsibility for loss ordamage in transit.

Transportation and insurance charges forreturn to owner will be paid by Kel-Tec if theclaim is covered by the warranty.

Under no circumstances shall Kel-Tec beresponsible for incidental or consequentialdamages with respect to economic loss orinjury or property damage, whether as a resultof breach of express or implied warranty,negligence or otherwise. Some states do notallow the exclusion or limitation or incidental orconsequential damages, so the above limitationor exclusion may not apply to you.

Kel-Tec will not be responsible for defectsresulting from careless handling, unauthorizedadjustments or modifications, defective orimproper ammunition, corrosion, neglect,abuse, ordinary wear and tear, or unreason-able use.

the firing pin pin, solvents can damage the O-ring used to hold it in place. Thoroughly dry allparts. Apply a light coat of oil to the firing pin,bolt, cam pin and the surfaces in the boltcarrier where the bolt, cam pin, and firing pinslide. Apply a light coat of oil on the piston rodand assemble the bolt carrier assembly andpistol as stated in the assembly part of thismanual. Manually cycle the bolt back and forthto check the function of the pistol. If any partsare damaged or badly worn or the pistol doesnot work correctly the pistol should not be firedand should be returned to Kel-Tec for servicingimmediately.

LUBRICATION WARNING:Firing a pistol with oil, grease, or anyother material even partially obstructingthe bore may damage the pistol andinjure the shooter and those nearby.Do not spray or apply lubricants directlyon ammunition. If the powder charge ofa cartridge is affected by the lubricant, itmay not be ignited, but the energy fromthe primer may be sufficient to push thebullet into the bore where it maybecome lodged. Firing a subsequentbullet into the obstructed bore willdamage the pistol and may injure theshooter and bystanders. Use lubricantsproperly. You are responsible for theproper care and maintenance of yourfirearm.

WARNING:It is not recommended that you disas-semble the grip of the PLR-16 pistol; thehammer spring is constantly undertension and can easily injure you orothers. If the need arises to lubricatethe trigger assembly do so through theaccess slot behind and in front of thehammer.

ServiceShould your PLR-16 pistol require adjustment,refinishing, or repair, it should be returnedunloaded to the factory. In shipping the PLR-16pistol, be sure to adhere to the following rules:

Individuals who wish to return the firearm forservice can do so by shipping via UPS prepaid.No return authorization number is required.

Include a letter of instruction, full name,address, phone number and the gun’s serialnumber. This will insure prompt service andhandling. Once your pistol has been received,anything other than warranty work, you willreceive a quotation. You will be notified of fullcharges and no work will commence beforereceiving your approval of our quotation. Alsosee Warranty Page for further instructions.All quotations are payable by C.O.D., VISA,M.C. or money orders only. No personal checksaccepted. Please return your PLR-16 pistol to:

Kel-Tec CNC, Inc. Service Dept.1475 Cox RoadCocoa FL 32926

104 BARREL EXTENSION108 BARREL RETAINER110 BOLT112 EXTRACTOR114 EXTRACTOR AXIS116 EJECTOR118 FIRING PIN120 BOLT CARRIER122 OPERATING HANDLE126 CAM PIN128 RECOIL SPRING CATCH130 PISTON HEAD134 FIRING PIN PIN140 TRIGGER BLOCK142 HAMMER144 SEAR145 SEAR SPRING PIN146 SAFETY150 STOCK SPACER-16154 SPACER-29158 ASSEMBLY PIN176 MAG CATCH SPRING178 HAMMER SPRING180 SEAR SPRING182 TRIGGER SPRING186 STOCK PIN SPRING190 BOLT STOP SPRING194 EXTRACTOR SPRING196 EJECTOR SPRING198 MAGAZINE SPRING203 DRIVER HOUSING204 MAGWELL205 PHILLIPS DRIVER207 RED O’RING208 TRIGGER210 EXTRACTOR SPRING BUFFER

216 RECEIVER SPREADER228 BOLT STOP234 MAG CATCH252 MAGAZINE HOUSING254 MAGAZINE FOLLOWER256 MAGAZINE PLATE258 MAGAZINE BOTTOM274 EJECTOR PIN276 RECEIVER SCREW278 RECEIVER WASHER280 SEAR PIN282 HAMMER AXIS284 BARREL EXTENSION PIN294 O’RING296 PISTON PIN298 TRIGGER AXIS299 GAS BLOCK PIN355 FRONT SIGHT POST357 FRONT SIGHT DETENT PIN366 REAR OPEN SIGHT367 REAR SIGHT ADJUSTER384 FRONT SIGHT DETENT PIN SPRING438 C-GAS HEAD501 BARREL502 COMPACT FOREND BARREL NUT504 LONG THREAD PROTECTOR512 PISTOL GRIP RIGHT514 PISTOL GRIP LEFT522 PISTOL RECEIVER524 D PISTON ROD533 PISTOL RECOIL SPRING TUBE538 PISTOL GAS BLOCK FRONT SIGHT575 PISTOL RECOIL SPRING310-MAGAZINE ASSEMBLY

PLR-16 Pistol Parts List Part# 522 Exchange Only

Notes Page