Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
WIRE SYSTEM
1
2
3
KICPRO15 ULTRA SMALL 15 FUSE 24 CIRCUIT 118 TERMINAL PANEL WIRE SYSTEM
IMPORTANT: The below instructions are referring to a general installation.
Your vehicle may vary from the vehicles described in these instructions. Use the
diagrams that best describe your vehicle.
ENGINE/FRONTSECTION
DASH SECTION
REAR SECTION
FUSE PANEL
STEERING SECTION
Please read the following instructions carefully.
Reading these instructions thoroughly will ensure a complete and trouble free installation. These instructions were designed after installing this system in different applications and should make this an easy job for any type of make and model vehicle that you are working on.
To help you with the installation, we have provided basic instructions for Ford, GM and Mopar systems. Please remember that these are basic instructions for your installation. The specific vehicle you're working on may require some modification for your application, depending on what accessories you plan to use. Whenever using after-market equipment or accessories, always use the diagrams provided with that equipment.
When we reference a specific wire, it will be shown with its label, then its color. The labeled wire in our instructions will match the label on the wire exactly. If a diagram or picture displays a wire that is not provided in the kit, then you will need to provide that wire. An example of this would be a ground wire. When installing ground wires, make sure the wire is connected directly to a solid chassis ground. We recommend that you use the color black for all ground wires during the installation.
Take good notes.
We have provided plenty of writing space throughout the instructions to make notes during the installation. Taking notes will help you with the install so you don't get lost along the way. In each section of the instructions, you will find a checklist that references the wires to be used. The checklists are labeled "Front", "Rear", "Dash" and "Steering". Here you will write down what wires you will use or not use. If you are using a wire from one section but routing it to a different section, make sure you write down the wire in the new checklist. An example of this could be the fuel pump wire. Go to the "Rear" Checklist, next to the fuel pump wire, write the words, "Front section" in the "Relocate" box. In some cases you might have some wires that you will not be using at all. Place a check mark or an "x" in the "Not Used" column pertaining to the checklist where that wire is located. Keep in mind that it's a good idea to leave this wire in the harness and it should also be routed to the proper location. An example of this would be the cruise control wire, since not all installations will have a cruise control system added to the vehicle. You should still route the wire to where a cruise control module would be installed, just in case a cruise control system is added at a later date. This will give you or your customer future options that can be added to the vehicle when needed.
Preparing the wire harness for installation.
You will need a large area to spread out the harness and prepare for the installation. The floor or a work bench would be a good location to get started. Your new wire harness kit will have four sections, "Front", "Rear", "Dash", "Steering", as described above.
Begin with the "Front" section of wires. These are the wires that will be mounted through the fire wall. Unwrap or uncoil the wires and lay them out straight towards the front of the vehicle. The next section of wires will be the "Tail" section. Unwrap or uncoil the wires and lay them out straight towards the rear of the vehicle. The remaining sections of wires are the "Dash" and the "Steering" column sections. The "Steering" column section has the two main connectors that are black and white. The last section is the "Dash" section. Unwrap or uncoil the wires and lay them out straight near the fuse panel.
To ensure correct wiring, start by removing all unused wires from the loom and work one section at a time. At this point of the installation it is important to remove each wire, one at a time, by pulling them through the cable ties in the harness.
Once all unused wires are removed from the harness, start to move the noted wires from one section to another by pulling them through the cable ties and into the desired section. Please take caution to ensure you insert the wire into all cable ties throughout the harness sections. Once completed, you can add any additional wires that are not provided in the system. To ensure accuracy and easy upgrades, please take notes on any additional circuits that you add.
5
4
USER GUIDE AND INSTALLATION MANUAL
ENGINE/FRONT CHECKLIST
Spec.No. Color
A1
B2
D3
14AWG
8AWG
14AWG
Black
Red
TanD1 14AWG Dark Green
H3
H4
H5
H6
16AWG
16AWG
16AWG
14AWG
Dark Blue
Light Green
Brown
Dark Green
ALT EXC
BATT
CHOKE
TACH
TEMP
REV.SWITCH
HI BEAM
16AWGA4 Light Green
RF TURN
FAN PWR
H30 16AWG Dark Green
RELOCATE NOT USED
Light BlueH7
H8
H10
H11
H12 12AWG Pink
14AWG
12AWG
16AWG
16AWGPink
Purple
Tan
HORN
H19 16AWG Light Green REV.LIGHT
H28 16AWG Dark Blue OIL
COIL
STARTER
F PARK LIGHT
LO BEAM
LF TURN
REAR CHECKLIST
ColorNo. Spec.
A8 16AWG White
D3 16AWG Tan
H16 Brown
H19 Light Green
H20 Tan
H22 White
H23 Yellow
H24 Dark Green
16AWG
16AWG
16AWG
16AWG
16AWG
16AWG
DOME LIGHT PWR
FUEL PUMP
R PARK LIGHTS
REV.LIGHT
FUEL GAUGE
LR TURN
RR TURN
BRAKE LIGHT
RELOCATE NOT USED
Mounting the fuse panel.
The best place to mount the fuse panel is in a flat dry location away from any heat source near the steering column. It is important to note that you should avoid running or mounting wire away from any moving parts such as: brake pedal, gas pedal, linkage controls, and steering controls. Once mounted, find a location on the firewall and drill a 1 1/4" hole to run all needed wires into the engine compartment of the vehicle.
Routing the wires.
The final step is to clean up your installation by grouping all the wires together and securing them with the cable ties that came in the kit. It is important to take your time and go section by section of your vehicle starting at the tail section and finishing at the dash section.
Engine & Front Section:Start by separating all the engine wires from the other wires in this section. At this point please reference the Front & TRear diagram(pg 5) to finish wiring your lights and accessories. To wire your engine please choose the best diagram that fits your vehicle from the Ford, Mopar, or GM sections. It is important to remember that you must use a fusible link on the red 10 gauge solenoid power wire. In the event you are using an AMP meter please reference the dash diagram's AMP meter section to insure correct installation.
Rear Section:Run all the wires to the back of the vehicle along your vehicle’s floor pan into the trunk area avoiding all moving parts. Use tape or cables ties to secure the wires to your vehicle. Once all the wires have been routed to the tail section you will need to hook up all appropriate wires including but not limited to your fuel gauge sender, tail lights, fuel pump, and dome light.
FUSE PANEL
ColorSpec.No. NOT USED
A1A2
A3
A4A5
A6
A7
A8A9
A10
B1B2C1
14AWG
14AWG
14AWG
16AWG
12AWG
Black
OrangeYellow
PinkBrown
YellowDark Blue
White
Green
14AWG
14AWG
16AWG
14AWG
10AWG Orange
12AWG8AWG
Brown
Red10AWG Yellow
ALT EXC
ACC 1
ACC 2
CRUISE/REV
HEATER
WIPER
IGNITION
CIG LIGHTER
DOME LIGHT PWR
KEYLESS
SHAVED DOORS
KEY ACC
BATT
D7
D10
D9
D8
D6
D5
D4
D3
D2
D1 14AWG Dark Green
Violet
Grey
Light Blue
White
Yellow
Red
Yellow
Tan
Grey16AWG
16AWG
12AWG
12AWG
16AWG
16AWG
16AWG
16AWG
12AWG
FAN PWR
GAUGES
CHOKE/FUEL
PWR WIN
PWR SEAT
RADIO ACC
BRAKE SWITCH
FLASHER
12V PORT
HEAD LIGHT
6
USER GUIDE AND INSTALLATION MANUAL
STEERING CHECKLIST
ColorSpec.No.
A2
A3
A9
12AWG
12AWG
14AWG
OrangeYellow
Green
A4A5
A6
A7
A7
A8
A10D2
D4
D5
D6
Pink
Brown16AWG
12AWG
14AWG
16AWG
14AWG
16AWG
10AWG
16AWG
12AWG
12AWG
16AWG
Yellow
Orange
Grey
Dark Blue
Orange
Grey
Yellow
Red
Yellow
CRUISE
HEATER
WIPER
RADIO BATT
CIG.LIGHTER
UNDER DASH LT
SHAVED DOORS
PWR WINDOW
PWR SEATS
RADIO ACC
GAUGES PWR
ACC 1
ACC 2
KEYLESS
D7D9
H13
H14
H6
H4
H3
H1
14AWG
16AWG
16AWG
Light Green
Dark Green
Brown16AWG Gray
H18
12AWG
16AWG
16AWG
H20
H21
16AWG
16AWG
16AWG
16AWG
White
Gray
Light Blue
White
Dark BlueTan
Light Blue
H28 16AWG Dark Blue
BRAKE SW PWR
12V PORT
DASH LIGHTS
TACH
OIL
DIMMER SWITCH
FUEL GAUGE
RF TURN IND.
BRAKE SWITCH
LF TURN IND.
TEMP
HI BEAM
H8 14AWG Tan LO BEAM
RELOCATE NOT USED
DASH CHECKLIST
Spec.No. Color RELOCATE NOT USED
B1 12AWG Brown
B2 Red
C1 10AWG Yellow
12AWG
H5 16AWG Dark Blue16AWG
16AWG
12AWG
12AWG
H7
H10
H11
H12
Light Blue
Purple
Pink
Pink
DASH LIGHTSGray16AWGH1
COIL
STARTER
F PARK LIGHTS
LF TURN
RF TURN
IGNITION
BATT
KEY ACC
16AWG
16AWG
16AWG
12AWG
H13
H14
H15
H18
H21
H22
H23
H24 16AWG
16AWG
16AWG
16AWG
Dark Green
Light Blue
White
Dark Blue
Light Blue
White
Yellow
Dark Green
D10
H16
H2912AWG Light Blue
16AWG
16AWG
Brown
Light Green
LF TURN IND.
BRAKE SWITCH
HORN
DIMMER SW
BRAKE LIGHT
LR TURN
RR TURN
HI BEAM IND.
HEAD LGT PWR
RF TURN IND.
R PARK LIGHTS
Steering Section:The steering column section has all the necessary wires for your vehicles steering column including your ignition switch, turn signals, dimmer switch, and more. Keep It Clean’s™ wire panel systems come prewired with two clear and black connectors for a GM steering column with a column mounted ignition switch. These connectors will plug in directly into your column mount ignition switch. In the event you use a different style of switch you may need to rewire the connectors. Please reference your switch diagram(pg 4) to ensure correct wiring. Keep It Clean's™ dimmer switch plug will fit GM floor mounted dimmer switches. Please reference the GM wiring section to choose the correct column plug and wire order for your vehicle.
All column plug wires are terminated and all plugs are letter coded. Please note that many styles of column connectors and wires have different colors and configurations. If your colors do not match or you are using a switch that is not mentioned, then you will need to use a digital volt ohm meter and test for the correct wires. To save time most ignition switch wires are marked on the back. In the event you are using late model GM van column you will need to reference the dash section's ignition switch diagram(pg 4). In most cases late model GM van column turn signals will work correctly on all Keep It Clean™ wire kits. Please test plug for compatibility.
Dash Section:To save time and to ensure easy installation, start wiring the dash from the driver’s side to the passenger’s side. Please keep in mind that the dash section contains several wires including but not limited to: heater, headlight switch, gauges, wiper, cooling fan, and more. Once all wires are connected use cable ties to group and secure the wires together. Make sure not to route or secure the wires to any moving parts.
Final Installation:By this time all wires should be connected or terminated and secured to your vehicle. To start your vehicle for the first time follow these easy steps:
A.Turn off all accessories.B. Close all doors, hood, and trunks.C. Place the ignition switch in the "OFF" position.D. Check to insure there is a fuse on the starter wire.E. Connect the negative battery cable to the battery.F. Check for current draw by connecting one side of a test light to the positive cable, and the other end to the positive side of the battery. If the light goes on you have a either a short or an accessory drawing power. To find the short remove each wire until the light goes out. If you have a dim or no light then it's safe to hook up the positive cable. G. Test the system and all accessories.
HEA
DLIG
HT PW
R [lig
ht blue]
DO
ME &
INTER
IOR LG
T RETU
RN
DA
SH LIG
HTS [g
ray]
F PARK
LGTS [p
urple]
LATE STY
LE GM
PARK
LGTS
DIM
MER
SW [lig
ht blue]
R PA
RK
LGTS [b
rown]
HI B
EAM
[light g
reen]
LO B
EAM
[tan]
KEY
ACC [b
rown]
STARTER
[pink
]
COIL [p
ink]
IGN
ITION
[yellow]
BA
TTERY [red
]BA
TIGN
ACC
ST
FUEL
METER
TEMP
METER
OIL
METER
VO
LTM
ETER
TACH
OM
ETERSPEED
OM
ETER
LFT TURN IND [light blue]
RT TURN IND [dark blue]
GAUGE POWER [grey]
FUEL GAUGE [tan]
TEMP GAUGE [green]
TACHOMETER [brown]
OIL PRESS. GAUGE [dark blue]
DASH LIGHTS [gray]
HIGH BEAM IND [dark green]
DASH S
ECTIO
N
USER GUIDE AND INSTALLATION MANUAL
DOM
E LIGH
T [white]
REV LIGH
T SW [light green]
REV LIGH
T [light green]
BRAKE LIG
HT [w
hite]
FUEL PU
MP [tan]
R PARK [brow
n]
LR TURN
[yellow]
RR TURN SIG
NA
L [dark green]
DOM
E LIGH
T
THIRD BRA
KE LIGH
T
TRUN
K LIGH
T
FUEL PU
MP
LICENSE PLATE LIG
HT
LR PARK
LR BRAKE
REV LIGH
T
REV LIGH
T
LR TURN
RR PARK
RR BRAKE
RR TURN
RR TURN SIG
NA
L [dark green]
FAN
[dark green]
RF TURN
[dark blue]
LF TURN
[light blue]
PARK [light green]
LOW
BEAM
[tan]
HIG
H BEA
M [light green]
HO
RN [dark green]
HO
RN
LF HEA
DLIGH
T
LF PARK
LF TURN
RF HEA
DLIGH
T
FAN
RF PARK
RF TURN
Rear
Front
FRO
NT &
REA
R D
IAG
RAM
S
USER GUIDE AND INSTALLATION MANUAL
F 2 3 4
ALT EXCITO
R [brown]
ALT-STA
RTER [red/wht]
Charg
ing S
yste
ms
EARLY
with ex
ternal
regula
tor
LATE
with interna
lreg
ulato
r
HIG
H O
UTP
UT W
IRE
STARTER
RS
+–
12
GM
SPEC
IFIC D
IAG
RAM
S
COIL PO
S [pink]
TACH
OM
ETER [white]
DIST
COIL
RESISTOR
STARTER
RS
+-
GM
Sta
ndard
Ignitio
n (P
OIN
TS TY
PE)
12
Engin
e C
onnectio
ns
+–
HEI
OIL SENDING [blue]
COIL POS [pink]TACHOMETER [white]
CHOKE [tan]
TEMP SENDING [green]
STARTER [violet]
STARTER
FRON
T
USER GUIDE AND INSTALLATION MANUAL
BAT
BAT
BAT
BAT
SR
MO
PAR S
PEC
IFIC D
IAG
RAM
S 1
OF 2
Charg
ing S
yste
ms
HIG
H O
UTP
UT W
IRE
STARTER
RS
+–
BAT
FLD
FLDIG
N
EARLY
LATE
ALT PO
WER [red-w
hite]A
LT EXCITOR [brow
n]
BAT
FLD
FLD
ELECTRO
NIC
REG
ULA
TOR
ELECTRO
NIC
REG
ULA
TOR
ALTER
NATO
R
ALTER
NATO
RMopar Ignition (START/RUN)
IG
BAT
ST SGL
COIL POS [pink]
STARTER [violet]
TACHOMETER [white]
DIST
COIL
RESISTOR
STARTER
S B
+ -
+ –
NEUTRALSAFETY SWITCH
STARTERRELAY
BAT
F
USER GUIDE AND INSTALLATION MANUAL
MO
PAR S
PEC
IFIC D
IAG
RAM
S 2
OF 2
Engin
e C
onnectio
ns
IG
BAT
ST SGL
+-
COIL POS [pink]
TACHOMETER [white]
CHOKE [tan]
STARTER [violet]
TEMP SENDING [green]
OIL SENDING [blue]
DIST
NEU
TRAL
SAFETY
SW
ITCH
STA
RTER
RELA
Y
STARTER
SB
+–
COIL
FRON
T
Mopar Ig
nitio
n (ELEC
TRO
NIC
)
DUA
L BALLA
ST RESISTOR
DIST
COIL
+-
COIL PO
S [pink]
TACH
OM
ETER [white]
BAT
USER GUIDE AND INSTALLATION MANUAL
FORD S
PEC
IFIC D
IAG
RAM
S 1
OF 2
Charg
ing S
yste
ms
ALT EXCITO
R [brown]
ALT-STA
RTER [red/wht]
ALTER
NATO
R
REG
ULA
TOR
STAN
DARD W
IRE
I A S F
S
F BA
T
HIG
H O
UTP
UT W
IRE
STARTER
RELA
Y
ALTER
NATO
R+
–
STARTER
Ford
Ignitio
n
FROM
NEU
TRAL
SAFETY SW
ITCH
STARTER
RELA
Y
ALTER
NATO
R
+
–
STARTER
SI
COIL PO
S [pink]
TACH
OM
ETER [white]
DIST
COIL
RESISTOR
+-
USER GUIDE AND INSTALLATION MANUAL
FORD S
PEC
IFIC D
IAG
RAM
S 2
OF 2
Ford
Ignitio
n (ELEC
TRO
NIC
) STARTER
RELA
YSI
TACH
[white]
[white]
[red]
[green][orange][purple][black]
COIL + [pink]
DIST
COIL
+-
ELECTRO
NIC
IGN
ITION
MO
DULE
Engin
e C
onnectio
ns
STARTER
RELA
Y
SI
+
–
COIL
+-
DIST
COIL POS [pink]TACHOMETER [white]
CHOKE [tan]
STARTER [violet]
TEMP SENDING [green]
OIL SENDING [blue]
FRON
T
USER GUIDE AND INSTALLATION MANUAL
USER GUIDE AND INSTALLATION MANUAL
16AWG Br
H26
H25
16AWG V
Color
D8
No.
16AWG
Spec.
V HORN/FLASHER
HAZARD
F1
E2 E1
F1
D8
F1
H25
B1
B2
H11
H12
B2
C1
USER GUIDE AND INSTALLATION MANUAL
H6
H8
H21
Co
lor
H27
No
.
8AW
G
Spec.
Red
H31
8AW
GRed
/Wh
t
BA
TT TO STA
RTER
ALT TO
STARTER
16AW
GB
r
H26
H25
16AW
GV
Co
lor
D8
No
.
16AW
G
Spec.
VH
ORN
/FLASH
ER
HA
ZA
RD
F1
E2E1
F1D8
F1
H25
B1B
2 H11
H12
B2
C1
Front V
iew
GAUGES
FAN PWR
CHOKE/FUEL
CRUSE/REV
ACC 1
ACC 2
AT EXC
PWR SEATS
PWR W
NDOW
HEATER
WPER
RADO ACC
KY
ESS/BRAKE SW
TCH PWR
SHAVED DOORHEAD LGHT
HORN/FLASHER12V PORT
CG LGHTER
DOME LGHT
15A 20A30A20A15A20A25A20A15A40A20A20A 25A 30A30A
BATT KEY ACC IGN TION
ENG
INE/
FRO
NT C
HEC
KLIS
T
Spec.
No.
Color
AB2D3
4AW
G
8AW
G
4AW
G
Black
Red
TanD
4AW
GD
ark Green
H3
H4
H5
H6
6AW
G
6AW
G
6AW
G
4AW
G
Dark Blue
Light Green
Brown
Dark G
reen
ALT EXC
BATT
CH
OKE
TAC
H
TEMP
REV.SWTC
H
HI BEA
M
6AW
GA
4Light G
reen
RF TURN
FAN
PWR
H30
6AWG
Dark G
reen
RELO
CATE
NO
T USED
Light BlueH
7
H8
H0
HH2
2AW
GPink
4AW
G
2AW
G
6AW
G
6AW
GPink
Purple
Tan
HO
RN
H9
6AW
GLight G
reenREV.LIG
HT
H28
6AW
GD
ark BlueO
L
CO
IL
STARTER
F PARK LIG
HT
LO BEA
M
LF TURN
REA
R C
HEC
KLIS
T
ColorN
o.Sp
ec.
A8
6AWG
White
D3
6AWG
Tan
H6
Brown
H9
Light Green
H20
Tan
H22
White
H23
Yellow
H24
Dark G
reen
6AWG
6AWG
6AWG
6AWG
6AWG
6AWG
DOM
E LIGHT PW
R
FUEL PU
MP
R PARK LIG
HTS
REV.LIGH
T
FUEL G
AU
GE
LR TURN
RR TURN
BRAKE LIG
HT
RELO
CATE
NO
T USED
FUSE P
AN
EL
ColorSp
ec.N
o.N
OT U
SED
AA2
A3
A4
A5
A6
A7
A8
A9
A0
BB2C
4AW
G
4AW
G
4AW
G
6AW
G
2AW
G
Black
Orange
Yellow
PinkBrow
n
YellowD
ark Blue
White
Green
4AW
G
4AW
G
6AW
G
4AW
G
0AW
GO
range
2AWG
8AW
G
Brown
Red0A
WG
Yellow
ALT EXC
AC
C
AC
C 2
CRU
ISE/REV
HEA
TER
WIPER
IGN
ITION
CIG
LIGH
TER
DO
ME LIG
HT PW
R
KEYLESS
SHA
VED D
OO
RS
KEY AC
C
BATT
D7
D0
D9
D8
D6
D5
D4
D3
D2
D4A
WG
Dark G
reen
Violet
Grey
Light Blue
White
Yellow
Red
Yellow
Tan
Grey
6AW
G6AW
G
2AW
G
2AW
G
6AW
G
6AW
G
6AW
G
6AW
G
2AWG
FAN
PWR
GA
UG
ES
CH
OKE/FU
EL
PWR W
IN
PWR SEA
T
RAD
IO A
CC
BRAKE SW
ITCH
FLASH
ER
2V PORT
HEA
D LIG
HT
DASH C
HEC
KLIS
T
Spec.
No.
ColorRELO
CATE
NO
T USED
B2AW
GBrow
n
B2Red
C0AW
GYellow
2AW
G
H5
6AW
GD
ark Blue
6AW
G
6AW
G
2AW
G
2AW
G
H7
H0
HH2
Light Blue
Purple
Pink
Pink
DA
SH LIG
HTS
Gray
6AW
GH
CO
IL
STARTER
F PARK LIG
HTS
LF TURN
RF TURN
GN
ITION
BATT
KEY AC
C
6AW
G
6AW
G
6AW
G
2AW
G
H3
H4
H5
H8
H2
H22
H23
H24
6AW
G
6AW
G
6AW
G
6AW
G
Dark G
reen
Light Blue
White
Dark Blue
Light Blue
White
Yellow
Dark G
reen
D0
H6
H29
2AW
GLight Blue
6AW
G
6AW
G
Brown
Light Green
LF TURN
IND
.
BRAKE SW
ITCH
HO
RN
DIM
MER SW
BRAKE LG
HT
LR TURN
RR TURN
HI BEA
M IN
D.
HEA
D LG
T PWR
RF TURN
IND
.
R PARK LIG
HTS
STEER
ING
CHEC
KLIS
T
ColorSp
ec.N
o.
A2
A3
A9
2AWG
2AWG
4AW
G
Orange
Yeow
Green
A4
A5
A6
A7
A7
A8
A0
D2
D4
D5
D6
Pink
Brown
6AW
G
2AW
G
4AW
G
6AW
G
4AW
G
6AW
G
0AW
G
6AW
G
2AW
G
2AW
G
6AW
G
Yeow
Orange
Grey
Dark B
ue
Orange
Grey
Yeow
Red
Yeow
CRU
ISE
HEA
TER
WIPER
RAD
IO BA
TT
CIG
.LIGH
TER
UN
DER D
ASH
LT
SHA
VED D
OO
RS
PWR W
IND
OW
PWR SEA
TS
RAD
IO A
CC
GA
UG
ES PWR
AC
C
AC
C 2
KEYLESS
D7
D9
H3
H4
H6
H4
H3
H
4AW
G
6AW
G
6AW
G
Light Green
Dark G
reen
Brown
6AW
GG
ray
H8
2AW
G
6AW
G
6AW
G
H20
H2
6AW
G
6AW
G
6AW
G
6AW
G
White
Gray
Light Bue
White
Dark B
ueTan
Light Bue
H28
6AW
GD
ark Bue
BRAKE SW
PWR
2V PORT
DA
SH LG
HTS
TAC
H
OIL
DIM
MER SW
ITCH
FUEL G
AU
GE
RF TURN
IND
.
BRAKE SW
TCH
LF TURN
IND
.
TEMP
HI BEA
M
H8
4AW
GTan
LO BEA
M
RELO
CATE
NO
T USED
OPTIONAL ACCESSORIES
USE THESE EXCELLENT ADD-ON ACCESSORIES TO ENHANCE YOURWIRE PANEL SYSTEM
• SIMPLE INSTALLATION• LONG LIFE AND RELIABLE OPERATION• BACKED BY A LIMITED LIFETIME WARRANTY
IGNITION SWITCH DIMMER SWITCH
BATTERY KILLHEADLIGHT SWITCH
RELAYS
Keep it Clean's headlight switch offers CAD design engerneering to provide a smooth operation! Keep It Clean's unique screw on design makes installation a snap, and offers a clean smooth look.
Keep It Clean's battery kill switch offers maximum performance and easy operation. The BATK CAD design offers a long life of smooth operation. Backed by a limited lifetime warranty.
Keep It Clean's heavy duty 40-amp relays are the best choice for any sort of 12-volt wiring project. Single-pull/Double-throw springs mean that your RA-1000 relays will never get stuck or short out on you. Combine the RA-1000 relay with the RAS relay socket, and you've just saved yourself hours of wiring time!
FLEX LOOM
Give your installations the ultimate professional appearance. Split Looms keep all your wires in place and protected from the elements, as well as giving any wiring job that final touch.
Keep it Clean's dimmer switch offers CAD design engerneering to provide a smooth operation! Keep It Clean's unique floor mount designmakes installation a snap, and offers a clean smooth look.
Keep it Cleans ignition switch offers CAD design engineering to provide a smooth operation! Keep It Clean's unique screw on design makes installation a snap, and offers a clean smooth look. Each switch comes w/ 4 heavy duty copper terminals w/ locking nuts for Ignition, Accessory, Battery, & Starter.
908 Lt. Green
909 Tan
907 Blue/Yellow
3-7/8” Plug
P NM L K J HGF E D
P NM L K J HGF E D
4-1/4” PLUG
6294642
6294641
BRN (12) 932RED (12) 934
PPL (14) 919
PNK (14) 931
ORN (18) 993
RED (12) 934
COLOR CODES FOR IGNITION SWITCH
WHITE HOUSINGBrown AccessoryRed Battery Power (B+)Pink Ignition Coil (smaller wire terminal)Purple Start
BLACK HOUSINGRed Battery Power (B+)Orange Accessory
NOTE: Orange wire will need a larger terminal (copper in color) than the others.
GM STEERING COLUMN REPLACEMENT
KICHARN10
TURN SIGNAL COLOR CODES FOR WIRE PORT
WHITE AND BLACK HOUSINGSBlack Horn Ground GLt. Blue Left Front Turn HBlue Right Front Turn JBrown Hazard Power KPurple Turn Signal Power LYellow Left Rear Turn MGreen Right Rear Turn NWhite Brake Light Input P
DIMMER SWITCH COLOR CODES
BLACK PYRAMID HOUSINGBlue/Yellow Power From Light SwitchTan low BeamsLt. Green High Beams
NOTE: Both the floor and column mounted switches use the same connector assembly.
Use this harness kit to replace or convert to a GM-keyed steering column.
GM Turn Signal connector
Steering Column Dimmer Switch
Floor Dimmer Switch