KCV-802R/D802R MANUAL

KCV-802R, KCV-D802R

[ Operating Installation Manual ]

www.kocom.co.kr

KCV-802R, KCV-D802R 08.01

�S�I�N�C�E

�1�9�7�6KOREA COMMUNICATIONS CO.,LTD

http://www.kocom.comE-mail : export@kocom.co.krThis manual is based on the date as shown in the right and specifications are subject tochange without notice for quality improvement

KC-MC30 KC-MC31 [Option]

7inch LCD Call from, and two-way communication with, door camera Going out of house or absence setup (When a user calls a door camera, images taken by the door camera is automatically recorded.) Selection of a lobby image and view of the selected imageImage screen setting Interlocking with PIR SENSOR, CCTV

4Cautions for safety

8Key Features

9Components

10Monitor Installation

11Door Camera Installation

12

14

18

Name of Each PartSpecificationsWiring DiagramFunctional Description

■

■

■

■

■

■

■

■

■15

30Warranty Card■

Contents

4 5

Cautions for Safety

Warnings

Warnings for disposal

Warnings & Cautions for Safety

For safe use, please stick to the following cautions.Read this cautions carefully and keep it within easy reach of you.For right installation, read this cautions thoroughly. Please install the product according to its specifications.This Cautions for Safety may include items that are not contained in specifications of the product that consumer purchases.Reading this cautions, use the product in a right manner. For further information, please contact our A/S center.

■

■

■

■

Do not throw used-up battery into fire places, which may cause fire and explosion.

The relevant law obliges users to have a qualified electrician carry out wiring work for power supply. Work by disqualified persons may cause fire and electric shock.

●

●

About SymbolA variety of symbols are used in this Cautions for Safety and your products to guide you to use products in a right and safe manner and to prevent possible risks for users and other persons and damages to their property. The meaning of each symbol is as follows. After fully aware of meaning of each symbol, read the following cautions.

This symbol means that wrong handling or ignorance of matters that this symbol indicates may cause serious injury or even death of user.

This symbol means that wrong handling or ignorance of matters that this symbol indicates may cause serious injury or property damage of user.

This symbol means the matter that user should not do at nay event.

This symbol means that user should follow the instructions.

This symbol means that contents (high voltage, electric shock, warnings, etc.) to which user should pay attention are included.

This symbol means that a certain action is not permitted. Specific points not permitted are depicted around this symbol (for example, in the left drawing, disassembly is not permitted.).�

This symbol means instructions or is used to force user to do a certain action. Specific instructions are depicted on the drawing (for example, the left drawing instructs user to detach power plug from an outlet).

Cautions

Cautions for installation

Be careful not to expose the product to benzene, thinner or hot water. Do not expose detergent directly to the product in a way of spraying, etc.

●

●

Moving equipment, be sure that the plug is detached from an outlet.For equipment whose cables are connected to terminals, please contact your local sales agent or qualified electrician.

●

●

When replacing old fuse with new one, do not directly touch it with bare hands. Use insulated tools or contact A/S center.

●

Do not put heavy thing on the product. Dropping or falling due to heavy things on it may cause injury of user.●

Cautions for Use

Cautions for Repairs and Maintenance

For the product of wall-mounting type with fixing pegs, keep it safely. Fixing pegs may cause injury of user.

●

Clean the dust inside the product regularly. Failure to clean the dust for long time may cause fire. For inspection and cleaning of the inside of product, please contact your local sales agent.

●

When putting your hands into the inside of equipment, be sure that plug is already detached form an outlet or circuit-breaker is turned off.

●

When installing the product on the wall, consider the thickness and material of the wall. Dropping in use may cause injury of user.

●

Install the product of wall-mounting type carefully not to drop from the wall. Dropping due to earthquake or tremors may cause injury of user.

●

Wiring work for communication cables need techniques and experiences. For this type of wiring work, please consult to your local sales agent.According to the standard for electric work and other relevant regulations, install communication cables at the place away from power cables. The failure to install cables separately may cause fire, electric shock and communication troubles.

●

●

Do not install the product on rolling table or sloping place. Dropping or falling may cause damage on your product.In installation, avoid the place exposed to tremor or shocks, which may cause damages on your product.Even if your product is waterproof, do not install it slanted place of water leakage, which may cause a short circuit.

●

●

●

6 7

Warnings

Cautions for UseThis product is not for perfect security solution.Do not handle the equipment with wet hand, which may cause electric shock. Do not place wet or metallic materials on equipment. Water leakage or intrusion of metallic materials may cause fire and electric shock. Do not block the ventilating opening of equipment or put alien substances into it, which may cause fire and electric shock.Do not use battery that is not designated or mix new battery with old ones. Insert batteries to fit their polarity. Explosion or leakage of battery may cause fire and injury of user.When visitor's image or voice is not displayed on screen or not sounded from speaker, please check his/her identity before opening the door and contact our A/S center.Do not use equipment when lighting is expected or strokes. It may cause fire and electric shock.Thie product is cannot be used for security.

●

●

●

●

●

●

●

●

When power cable is broken (exposure of core or short-circuit), do not fail to replace broken cable with new one. Failure to replace broken power cable may cause fire and electric shock.When detecting any abnormalities in equipment (communication is not available, images do not be displayed on screen, calling is not available, or abnormal sound is heard), immediately detach plug from an outlet, or turn off circuit breaker or detach batteries from equipment (in case that equipment has no plug) before requesting repairs to sales agent or A/S center. Keeping connection to power supply may cause fire and electric shock. When alien substances go into equipment, immediately detach plug from an outlet, or turn off circuit breaker or detach batteries from equipment (in case that equipment has no plug) before requesting repair to sales agent or A/S center.In the case of smoke or smell of unknown origin from equipment, keeping use it may cause fire and electric shock. Detach plug from an outlet, or turn off circuit breaker or detach batteries from equipment (in case that equipment has no plug) and be sure to check no more smoke or smell from equipment before requesting repair to sales agent or A/S center. Since personal repairing work by user may serious accidents. In any case, do not repair equipment with your own hand. When dropping equipment or breaking its cabinet, detach plug from an outlet, or turn off circuit breaker or detach batteries from equipment (in case that equipment has no plug) before requesting repair to sales agent or A/S center.Keeping use equipment may cause fire and electric shock.Avoid direct exposure to sunlight and store equipment at the place free from dust and high temperature as you can. High temperature of equipment may cause fire and electric shock.

●

●

●

●

●

●

Cautions for AbnormalityWhen moving equipment, be sure that plug is detached from an outlet and communication cable is disconnected. Damage on cables may cause fire.

●

Voltage other than prescribed rated voltage is not permitted, which cause fire and electric shock. Do not use power terminal of product's main body in other equipment than prescribed ones. It may cause fire and short- circuit.

●

●

In wiring work, use the designated wiring materials. Wiring work using other materials than designated ones may cause fire.

●

Warnings

Cautions for UseDo not install the product at bathroom or at the place near a washing machine, or at other humid places. It may cause fire or electric shock.Do not install the product at the place near a dresser, humidifier or heater. Also avoid the place exposed to spark, heat or humidity. All of them may cause fire and electric shock.Do not install the product at the place exposed to dust, metals and harmful gas such as hydrogen sulfide gas.All of which may cause fire and electric shock.Do not install the product at the place exposed to water and chemicals. This may cause fire and electric shock.Do not scratch, break or arbitrarily process power cable, which may cause fire and electric shock. Putting a heavy thing on a cable, heating it or pulling it, may cause impairment on it. Do not place power cable at the place near heating equipment. It may cause damage of cable's clothing material, which results in fire and electric shock. When detaching plug from an outlet, do not pull power cable.Damages on power cable may cause fire and electric shock. When detaching plug from an outlet, please hold the plug tightly. Do not detach plug from an outlet with wet hand. It may cause electric shock.

●

●

●

●

●

●

●

●

When using the existing wiring, be sure of the suitability of it to the product and install the product. Failure to this caution may cause fire.

●

The equipment without waterproof marking should not be installed at the place water leaks. It may cause electric shock and short circuit.When working, be sure that power is disconnected. Failure to disconnect power may cause electric shock.

●

●

Be sure that the power cable is connected and earths according to designated method. Failure to connection and earth may cause fire.

●

Do not connect power to other terminals than designated ones.It may cause fire and electric shock.

●

When building a system with the product, do not connect the product to other equipment than designated one. It may cause fire.

●

When installing A/C switch, do work after removing the substance that may cause short circuit or electric shock.Before installing or providing A/S service, be sure that the power is disconnected.

●

●

Do not open rear cover, cabinet and cover of equipment. It may cause electric shock.

●

Do not modify power cable or pull it with excessive strength, which may cause fire and electric shock.Do not modify equipment. It may cause fire and electric shock.Call signal may cause damage on user's hearing ability.

●

●

●

8 9

Cautions for Use

Cautions for Installation

Abovementioned cases may cause troubles in the product. Please be careful to the cautions in use of the product

● This product is designed as a precision electronic device, so do not disassemble it at user's discretion.● Comply with the specifications provided by KOCOM in installation of the product.● Do not touch the product with foreign things (e.g. sticker, magnet, bottle opener, iron chopsticks, etc.) and do not bring them in the product. (It may not only shorten the durability of the product but also bring danger to users.)● During the rainy season, rainwater may flow in the product along its wiring and affect the system. So, the end of wiring is required to finish with letter 'U' type.

● Do not place the product near humidifier, heater, etc. High temperature and humidity may cause troubles.● Do not drop, or give a strong impact on, main body and gate camera.● Do not place the main body near the things emitting strong magnetism (e.g. TV, speaker, etc) (it may cause the drift or distortion of screen, resulting in troubles)● Do not clean the product with wet hands, or using volatile liquids such as benzene or thinner.● Clean up camera and window part of main body from time to time to keep fine and clear image quality.● This product is designed as a precision electronic device, so do not disassemble it at user's discretion.

●Call from, and two-way communication with, multi-family lobby-phone (KLP-100 Series)●Two-way call and communication with multi-family security phone (KIP-120 Series)●Two-way call and communication between house devices using extension line (KIV-212, KIP-603, KCV-802R, KIV-102)●Call from, and two-way communication with, door camera ●Two-way call and communication with a privately installed exchanger or switchboard●Going out of house or absence (Security) setup (When a user calls a door camera, images taken by the door camera is automatically recorded.) ●Selection of a lobby image and view of the selected image●Color control, Tone ring change ●ID setting of house device●Input of guard office No. in a privately installed exchanger●Input of the password No. for opening of lobby door in a privately installed exchanger ●Prior setting of multi-family security, analogue security, and private exchanger●Special connection points ON/OFF ●Image screen setting ●Interlocking with PIR SENSOR, CCTV

Key Features

●This product is a multi-functional house device equipped with 7inch(17.8cm)LCD suitable to multi-family houses.●It provides functions such as identification of, and communication with, a visitor at lobby-phone and automatic open/close of a common gate where a lobby-phone is installed using house device. It may also, if equipped with multi-family security phone, provides two-way call and communication with guard office. ●In addition, this product can be compatibly used with any existing analogue-type security phone. When a user is employing an analogue-type security, he/she may purchase a separate module for analogue security. This product is designed to enable a user to directly open the lower part of the product and connect the module to that part.●As this product, basically adopts OSD and image memory functions, it may control and adjust each function using its arrow key and, if a user is going out of house or selects the function, save and store scenes of images taken. ●Moreover, this product provides a user with two-way call and communication with a privately installed exchanger or switchboard. Even in a power failure, a user can communicate with the exchanger. (In this case, however, a privately installed exchanger should be running normally.)

Components

Overview

4 pin cable for camera &sub audio phone(KDP-602G)

Wiring Lines of Multi-home Main Line 9P

3P

2P

4Px2Wiring Lines of Security Sensor

Wiring Lines of Private Exchanger 2P

Wiring Lines of GUARD

MonitorWall Hanger Bracket

CCTV Camera or DVR connection cable

Door Camera Rear Bracket

AC type

4X25mm 4ea 3X8mm 1ea

Screws for fixing Monitor

4X25mm 4ea

4X8mm 1ea

"L" Wrench

Screws for fixing Camera

Screw cap(Only KC-MC31)

DC15V Adapter

1110

Installation Precaution

Monitor and camera must be installed away from direct light and counter light.Camera must be installed at a place free from rain.Standard height of monitor must be 1,450mm~1,500mm from ground, centered around brawn tube.Camera should be installed on the wall in which cement is completely dry.If installed during winter season at temperature below -5℃� condensation might be generated inside monitor and camera due to temperature difference between indoors and outdoors. To prevent breakdown due to such condensation, connection should be made in 2 hours or more after installation.Do not install monitor and camera in locations subject to direct heating as harmful gases may subsequently be emitted in significant amounts.

●

●

●

●

●

● Stopping up pipe as above minimizes temperature difference between indoors and outdoors, and also eliminates moisture and condensation on door camera window.

※

Stop up P.V.C. pipe usingadiabatic substances, to prevent

air circulation

Door Camera Installation

Surface-mounting Door Camera Installation

Standard height of the door camera is 1,400mm~1,450mm from the bottom of one camera to the floor.In case that the height of Door camera exceeds the range of min. 1,250mm~1,550mm, it is impossible to control the screen picture with only the lens angle, and therefore, be careful of the height of camera installation.

Standard Height of Door Camera●

●

Bottom base ofOne hall Box

Surface mount

(unit:mm)

※Before installation, do not fail to shut the piping. Monitor Installation

Standard height of monitor is ranged 1,450 ~ 1,500 from bottom to the center of monitor screen.For installation, avoid the places where there is any excessive humidity,magnetic force, dangerous chemicals, direct ray of sun, and any places near a heater which can cause break down.

Standard height monitor●

●

Bottom of 1 Rectangularswitch box

Center of moniter

(unit:mm)

1 2 3

4 5

Rear

END

Rear

6

4X25mmScrew

Wall hangerbracket

3X8mmScrew

KC-MC30 KC-MC31Wall

4X25mmScrew

4X8mmScrew

Wrench

Name plate

Wall

4X25mmScrew

4X8mmScrew

Wrench

Screwcap

Standard wire strip specification : 6~7mmStandard wire (AWG) : 16~24(0.5mm~1.2mm)

Camera Terminal Block

Camera Camera

Rear Bracket Rear Bracket

Standard wire strip specification : 6~7mmStandard wire (AWG) : 16~24(0.5mm~1.2mm)

Camera Terminal Block

Do not install the door camera in the place under direct sunlight shines, it may make faint image or white stripe or round form line on the image. If this phenomenon appears on the monitor's image, it is not mechanical trouble, so please replace the door camera to keep away direct sunlight or change the direction of the door camera.

※�C�A�U�T�I�O�N

12 13

Name of Each Part Name of Each Part

�1

�7

�2 �3�4

�5 �6

1

NameNo

2

3

4

5

6

7

Brief DescriptionHandset used in communication (sending/receiving) between camera and the extension line of interphone

Security/Lobby Button

used in a call to security phone or an incoming call from security or lobby phone

used in a call to/from multi-family interphone and OSD menu cancle

◁ Left Button

(A)Pressing this button with the handset being hung up, a user can view images from door camera 1 or 2.)(B) used as Left button in setting OSD menu.

(A) saves (RECORD) images from Camera 1 & 2(B) used as Up button in setting OSD menu

△ Up Button

(A) plays images saved in standby mode - used as Forward key(B) used as Right button in setting OSD menu

▷ Right Button

(A) used as Delete key in playing images(B) used as Down button in setting OSD menu

▽ Down Button

(A) Entrance into User's OSD (Press the button lightly to enter into User's OSD)(B) Change of User's OSD MENU(C) Entrance into Installer's OSD (Press the button for more than 5 seconds to enter into Installer's OSD)

Menu/OK Button

used in a call and communication with private exchangerTEL/Absence Button

Extension Line Button

works door open function of camera when a user press this button with communicating with gate camera

If a user presses one or more of 12 keys for extension line after pressing Extension Line button, a call signal is sent to a house device or an exchanger phone to which the selected number is assigned.

※In case a trouble arises from the user's arbitrary modification of installer's OSD menu, charges for any after-sales service (A/S) due to the trouble should be paid by a user even during the warranted A/S period.

Door Open Button

12 Keys for Extension Line

/

Front

�8

Name Brief DescriptionNo Tone Ring

Wall-mounting

Modular Jack

adjusts volume of tone ring (low to loud)Volume Switch

a jack for handset connection cord

a hole for a screw used in fixation of main body in its wall-Fixation Part

Power Switch on/off switch for main power supply for monitor

�9

�1�0

�1�1

Out Terminal�1�2 Devices for each of the connection points

Output Connection Parts

A : Analogue-type Security Master(2P) D : Multi-family Main Wiring(9P)B : Camera 1(4P) E : Security Sensor(3P)C : Camera 2(4P) F : Program write port(7P)

�1�3

Monitor

Door Camera

Monitor

A BD E

CF

Bottom View

Rear View

KC-MC30 KC-MC31 KC-MC30 KC-MC31

1. C-Mic : To communicate with Monitor2. Camera Lens3. LED4. Speaker : When visitor calls, the voice from monitor comes out of the speaker.5. Call Button : By pressing the button, the related house will be called.6. Name plate7. Screw cap

FG(FRAME GROUND) FG(FRAME GROUND)

①②③④⑤⑥

⑦

⑧ ⑧①②③④⑤⑥

①� �:� �V�C�C②� �:� �G�N�D③� �:� �A�u�d�i�o④� �:� �V�i�d�e�o⑤�&⑥� �:� �D�o�o�r� �(�N�o�n�-�P�o�l�a�r�i�t�y�)⑦� �:� �C�a�m�e�r�a� �a�n�g�l�e� �k�n�o�b� � � � � � �(�O�n�l�y� �K�C�-�M�C�3�0�)⑧� �:� �W�i�r�e� �c�l�a�m�p

�1

�2

�3

�4

�5

�6

�1

�2

�3

�4

�5

�7

�1�2

�1�3

A BD E F

C

�8 �9 �1�0 �1�1

1514

Wiring Diagram

Wiring Diagram-Private Exchanger

Private Exchanger

PABX�1�.�T�I�P�2�.�R�I�N�G

AC INPUT

Main monitoir

1 2

1 2

KCV-D802R

DC 13V

Product Specifications

Model no.

Power Input

Tone Ring

Door Camera Monitoring

Lobby Phone Monitoring

Function

Communication Type

Image Displaying Time

No. of Wiring

Communication

Distance

Guaranteed Operational

Temperature of Monitor

Dimension

※Notes : Multi-family image 100m is a distance in case lobby phone image amplifier (KHU-102P) is used.

KCV-802R

AC 100V - 240V (unload : Min. 4.9W, inload : Max. 22W)

24 POLY (Max.) - continues for 30 seconds in the event of an incoming call

Using ◁ LEFT buttons, a user can monitor the outside of the door.

A user can monitor lobby phone by selecting a multiple-family lobby phone in OSD menu and calling it.

(For detailed information, see Functional Description.)

[However, this function is only available in TEN KEY Lobby phone (KLP-100 Series)]

Handset type (2-way)

For 30 seconds in the event of a call to door camera or lobby phone

For 3 minutes in the event of a communication with door camera or lobby phone

Door camera - polarized 4 lines, more than IV 0.65mm only

Multi-family Main Wiring - VOICE1/VOICE2/DATA: Polarized, more than IV 0.8mm only

Video Wiring - COAXIAL 5C-2V

Power - Polarized 2 lines, more than IV 1.2mm only

Door Camera - 50m for 0.65mm

Multi-family main wiring - 300m for IV 0.8mm

Multi-family image - 100m for COAXIAL 5C-2V

0℃ - 50℃

295(W)X171(H)X48(D) mm

Wiring

Distance

Multi-family Wiring - Polarized 5 Lines (VCC/GNC/COM1/COM2/DATA) 1 Line (VIDEO) Door Camera Wiring - Polarized 4 lines (VCC[12V]/GND/VOICE/VIDEO)Security Sensor Wiring - Polarized 3 lines (VCC[12V]/SIGNAL IN/GND)Private Exchanger Wiring - Non polarized 2 lines (TIP/RING) Distance of Multi family Wiring - Power : Within 1.2Φ (VCC/GND) 300m COM1/COM2/DATA : within 0.8Φ 300m Coaxial Cable : within 5C2V 100mDistance of Door Camera Wiring - Within Φ0.65 TWIST SINGLE CABLE / 50mDistance of Security Sensor Wiring - Within Φ0.65 TWIST SINGLE CABLE / 30m Distance of Private Exchanger Wiring - Distance according to the standard of private exchanger

Model No. Power Supply DC 12V ± 1V(power from monitor)Power Consumption 3W(In Load)Operation Temperature -10 - +50℃Min. Illumination 0.1Lux (LED ON)Dimension (mm) 110(W)x158(H)x39(D)mmAngle of Lens Diagonal 81°(angle adjustable)

KC-MC31

110(W)x158(H)x34(D)mmDiagonal 81°

KC-MC30

This product is an interlocking device of private exchanger, not a telephone.※�C�A�U�T�I�O�N

16 17

Wiring Diagram

Wiring Diagram

Wiring Diagram

Wiring Diagram-multi family

1.POWER2.GND3.VOICE4.VIDEO

※Cautions1. Pin No.6(data line) in Main Line Port is not connected in sub video phone.2. Pin No. 1,2,3,4,5,6,7,8 in Main Line Port are used in a form of parallel connection between main monitor and sub monitor.3. The DIP swich in sub unit should be set as "0000"

Security Sensor(Mangetic Sensor)

Door Opener, or Sprinkler, or Devices for each of the connection points

1.+17V2.GND3.VOICE 14.VOICE 25.VIDEO INPUT6.DATA7.PABX (internal line)8.DATA-PABX9.VIDEO OUT

SUB monitor

MAIN monitor

Mode Setting - In MENU Home, select one out of "Multi,"

Camera

AC INPUT

①

1 9④① ④

① ④① ④

1 9 1 3

1 3

AC INPUT

�O�P�T�I�O�N

①

②

③

④

⑤

⑥

①

②

③

④

⑤

⑥

�1�.�+�1�2�V�2�.�S�i�g�n�a�l�3�.�G�N�D

Camera, Sub monitor, Devices for each of the connection points, Security Sensor

MAIN monitor

SUB monitor

�1 �9

�1 �9

AC INPUT

AC INPUT

�O�P�T�I�O�N

Multi-family Main Wiring

Lobby Video-in (5C-2V)

Multi-family Main WiringConnection to Upper-floor Main Wiring

Connection to Upper-floor Videophone

DC INPUT

/

19

Functional Description Functional Description

Communication

1. Call from Gate

A visitor presses CALL button on gate camera.

"CAMERA1" or "CAMERA2" message is displayed in monitor and tone ring sounds. (Stand-by time : 30 seconds)

On hanging up phone, If a user presses ◁button, the image of Camera 1 is seen. If a user presses ◁button once again, the image of Camera 2 is seen.

2. View of Door Camera Image

Communication

Pick up the handset to communicate. (Available communication time : 3 minutes)

3. Call from Multi-family Lobby Phone

Lobby/Security LED flickers and tone ring sounds. If a user picks up the handset, communication is made available. If a user presses button during the communication, common gate connected to multi-family lobby phone is opened.

※Above descriptions may vary with the camera setups. Above descriptions is based on a situation that CAMERA1 and CAMERA2 is turned on ('O') in MENU ' Device.

/

CAMERA 1

/

/

If a use presses button during the communication with door, the door is opened.

Hang up the handset to finish communication.

/

If a user presses ◁button once again, this function ends. (Available image view time : 30 seconds)

/

/

/

If a user picks up the handset while viewing the image, communication is made available. If a user pressesbutton during the communication, the door is opened.

/

18

※When CAM2 is set as "P"(PIR), monitoring function of CAM2 does not work.

21

Functional Description Functional Description

Communication

4. Call from Multi-family Security Phone

If a user picks up the handset and presses button, LED on and tone ring sounds.

7. Call to Multi-family House Device

Communication

If the other party picks up the handset, communication is made available.

If the other party picks up the handset, communication is made available.

Pick up the handset to communicate with the device.

/

Lobby/Security LED flickers and tone ring sounds.

/

/

//

Pick up the handset to communicate with the security phone.

5. Call to Multi-family Security Phone

If a user picks up the handset and presses button, Lobby/Security LED on and tone ring sounds.

If the other party picks up the handset, communication is made available.

6. Call from Multi-family House Device

LED of multi-family extension line flickers and tone ring sounds

/

/

/

20

8. Call from Private Exchanger Phone

TEL/Going-out LED flickers and tone ring sounds.

9. Call to Private Exchanger Phone

If a user picks up the handset and presses button, LED flickers and tone ring sounds.

When a user inputs the exchanger No. of the other party, tone ring sounds.

/

/

/

/

/

/

/

23

Functional Description Functional Description

Communication Communication

22

10. Functional Description of Common Gate Lobby Phone

Call No. 70 guard master with holding on the phone after setting 'MENU -> CALL -> GUARD -> 70' on hanging up the phone.

No. 70 guard master can talk by holding on the phone.

/

�C�A�L�L

�G�U�A�R�D

�L�O�B�B�Y�

�7�0

�0�0

�M�E�N�U� �:� �L�C�D� � � � � � � � � � � � � �

※This function is only for KLP-100 series.

Hold on the phone on monitoring and to communicate is possible. (But selected call and monitoring will not working if lobby phone or guard is on the phone call.

11. Monitoring Function of Common Gate Lobby Phone

Be monitoring the selected common gate lobby phone with pressing the button 'MENU -> CALL -> LOBBY -> 02 -> LOBBY/GUARD' on hanging up the phone

//

�C�A�L�L

�G�U�A�R�D

�L�O�B�B�Y�

�0�0

�0�2

�M�E�N�U� �:� �L�C�D� � � � � � � � � � � � � �

/

12. Selected Call Function of Guard Master

After selecting the number on MENU -> CALL -> TEL on hanging up the phone, hold on phone and can call the selected number.

Hold on the phone and the selected house can communicate.

/

�C�A�L�L

�G�U�A�R�D

�L�O�B�B�Y�

�0�0

�0�0

�M�E�N�U� �:� �L�C�D� � � � � � � � � � � � � �

13. Saving, Playing and Deleting Images

While call from, or communication with, door camera or lobby phone, press △button to save image.

Press ▷ to view the saved image. A user can view the saved image in a 6-divided format.

/ /

To enlarge the image, select Screen and press Menu button. (To return to the previous 6-divided image, press Menu button once again.)

//

Press ▽button during 2 seconds and each image can be deleted. Keep pressing ▽button and all images will be deleted one by one.

Using set the product an it's ID No. you want to make a call and press Communication is made available if a user picks up the handset.※LOBBY = Multi-family Lobby Phone For making a call to all guard, set the number of GUARD as 99

25

Functional Description Functional Description

Absent Mode

24

14. Setting/Cancelling the Absent Mode

If a user presses button with the handset eing hung up, Going-out LED is turned on. (To turn the LED off, press the button once again.)

/

/

1. Security sensor inactive during 60 secs. in absent mode(Time for user to go out of the house)2. In 60 secs. a user can cancel absent mode3. Absent mode ON after 60 secs. (security sensor active)4. When alarming, press button for 2 secs. to cancel the alarm5. On DEVICE of OSD menu, a user can change absent mode details6. Alarm call is not made to Private Exchanger

OSD function (LCD CONTROL MENU)

1. CALL (push menu button once)

Call to Multi-family Lobby Phone & Segurity Phone and Private Exchanger

�3

�C�A�L�L

�L�O�B�B�Y�1▷ ▷ �5

�C�A�L�L

�L�O�B�B�Y�1

2. DEVICE (push menu button twice)

�O�F�F�1�0�M�I�N�U�T�E�N�O�2�3�0�S�E�C�3�0�S�E�C

�D�E�V�I�C�E�S�W�I�T�C�H�A�L�A�R�M� �T�I�M�E�A�L�A�R�M� �C�A�L�L�C�A�L�L� �T�I�M�E�S�C�A�M�1� �T�I�M�E�C�A�M�2� �T�I�M�E

1) SWITCH OFF : Devices for each of the connection point are disconnected. If a user changes it's condition to 'ON', the devices are connected and take action.� ※DOOR OPEN on this means DOOR OPEN is set as CAMERA on Installation Menu and a user cannot control SWITCH OFF/ON. 2) ALARM TIME 10 MINUTES : Alarming for 10 minutes ALARM TIME 30 MINUTES : Alarming for 20 minutes ALARM TIME CONTINUE : Continue alarming until cancellation ( * Alarm cancellation: press for 2 secs.)3) ALARM CALL NO : Do not make alarm call ALARM CALL GUARD 1 : Make alarm call to GUARD 1 ALARM CALL GUARD 2 : Make alarm call to GUARD 2 ※CAUTION : Alarm call is not made to Private Exchanger

/

/

/

Please push menu button for this function. Select and change using Contents can be changed according to product's version.

27

Functional Description Functional Description

26

3. LCD function

A user can change a Color & brightness level.

�5�0�5�0�5�0

�L�C�D

�C�O�N�T�R�A�S�T�B�R�I�G�H�T�N�E�S�S�C�O�L�O�R�A�U�T�O� �A�D�J�U�S�T

▷ ▷ �7�0�5�0�5�0

�L�C�D

�C�O�N�T�R�A�S�T�B�R�I�G�H�T�N�E�S�S�C�O�L�O�R�A�U�T�O� �A�D�J�U�S�T

4.Melody function

�0�4�0�6�1�6�0�5�1�2�1�4

�M�E�L�O�D�Y

�C�A�M�E�R�A�1�C�A�M�E�R�A�2�L�O�B�B�Y�G�U�A�R�D�I�N�T�E�R�P�H�O�N�E�P�A�B�X

Changing Color & brightness. Please, use control key

Selecting AUTO ADJUST, tone of color back to initialization※Caution : Minimum set point of color is 20

※It can select melody No.1~18.

A user can change melody.Using control key customer can change melody.

4) CALL TIMES 1 : Make alarm Call one time. CALL TIMES 2 : Make alarm Call two time. CALL TIMES 3 : Make alarm Call three time.5) CAM1 TIME 30SEC : 30 sec. of CAM1 monitoring time. CAM1 TIME 5 MINUTE : 5Min. of CAM1 monitoring time. CAM1 TIME 10 MINUTE : 10Min. of CAM1 monitoring time.6) CAM2 TIME 30SEC : 30 sec. of CAM2 monitoring time. CAM2 TIME 5 MINUTE : 5Min. of CAM2 monitoring time. CAM2 TIME 10 MINUTE : 10Min. of CAM2 monitoring time.

CAMERA1 CAMERA2 LOBBY = Common gate phone or Lobby phoneGUARD = Guard master phone INTERPHONEPABX = Private Exchanger

6.Installer Menu (LCD OSD Menu)

�0�0�0�1�0�0�M�U�L�T�I�O�L�D�C�A�M�E�R�A�N�O�R�M�A�L� �O�P�E�N

�S�Y�S�T�E�M

�I�D� �C�A�M�E�R�A�1� �C�A�M�E�R�A�2� �M�O�D�E�P�R�O�T�O�C�O�L� �D�O�O�R�O�P�E�N� � �S�E�N�S�E�R� �I�N�I�T�I�A�L

�S�Y�S�T�M�E� �S�W� �V�e�r� �:� �X�.�X�X

5.Date set up & Image deletes function

Date, time, image data deleting function.

1) TIME : Changing Date, time using control key Press menu to set up date and time. Please, use control key ◁▷ to set up, control key ▽△ to set up the time.2) FORMAT : Using control key can deletes image. On format menu, press menu to make set up menu. Using use left & right control key ◁▷ choosing YES or NO, and press MENU button (YES : ALL Delets, NO : Cancel).To Exit menu. Please, press intercom button.

�M�E�M�U

▷▷�T�I�M�E� �:� �0�6�:�2�2� �A�M� �2�2�/�0�2�/�2�0�2�2� � � � �F�O�R�M�A�T� �:� � � � �Y�E�S� � � � � �N�O

�M�E�M�U

▷▷�T�I�M�E� �:� �0�6�:�2�2� �A�M� �2�2�/�0�2�/�2�0�2�2� � � � �F�O�R�M�A�T� �:� � � � �Y�E�S� � � � � �N�O

2) SYSTEM SW Ver XXXX : It is Version of Firmware and it can be change without notice.3) ID0001 : Muliti Apartment ID Mode. -> In case of 000 ID working as intercom without Call Menu, it will display main Define with ALARM TIME, ALARM CALL. -> Depends on unit protocol, it can change with setting up rage. => PROTOCOL OLD : 1~63, 100~963, 1000~1963, 2000~3963 => PROTOCOL New : New protocol set up 1~1599

1) Installer MENU : Please, press two second of Menu button, and press, door open button to get into installer menu function.

※Caution : Wrong set occurs malfunction. Please, follow manual.

All status can select with control key

29

Functional Description

28

4) CAMERA1 O : Select CAMERA1 CAMERA1 X : Not select CAMERA1 5) CAMERA2 O : Select CAMERA2 CAMERA2 X : Not select CAMERA2 CAMERA2 P : Select PIR Sensor Camera (Extra Sale) After PIR sensor on, the monitor will be turned on during 2' 30''. (It is possible only for CAMERA2.)6) MODE MULTI : set for the common gate system products. MODE PABX : will let the guard master be compatible to communicate. It is compatible with the common gate products. MODE ANALOG : set for the ANALOG guard master. �-�>� On MODE ANALOG, the call menu will disappear and won't be compatible with the common gate products and serve phone. ※MODE Selection can be added according to the firmware version and the function will different according to the selected Mode. 7) PROTOCOL OLD : set for the compatibility with the old common gate systems. PROTOCOL NEW : It can be set from 1 to 1599 and ID number over 63. 8) DOOR OPEN CAMERA : Output the door open signal to CAMERA 1 and 2. DOOR OPEN MONITOR : Output the door open signal to MONITOR outside signal point. ※Caution: Set to Monitor and DOOR OPEN appears on DEVICE �-�> SWITCH and can not control SWITCH ON/OFF. 9) SENSOR NORMAL OPEN : According to the point type of input sensor, set 'normal - opened (not active), closed (active). SENSOR NORMAL CLOSE : According to the point type of input sensor, set 'normal - closed (not active), opened (active).10) INITIAL �-�> MENU SW ENTER: Press the menu for default.

※Caution for Protocol set of the common gate products Set the entire common gate products with a same Protocol and the call and communication will be possible. Wrong set occurs malfunction.

3130

Warranty

Warranty Card

KOCOM Warranties the original purchaser of this product as follows. 1) This product is produced under strict quality control and inspection procedures. 2) If this product breaks down during proper use as a result of product defect, KOCOM will repair it within one year from date of purchase free of charge. 3) The following cases will be subject to charge, even during warranty period: a. Breakdown during transport, or through careless treatment, by consumer. b. Breakdown cause by unauthorized repair, or system modification. c. Breakdown caused by natural disaster or power disorder.

To receive after-Sale service, have the following ready when you contact our branches.1. Name of the product.2. Model number of the product.3. The area of problem.4. Phone number and address at which you can be contacted.

PRODUCT

MODEL

DATE PURCHASED

WARRANTY PERIOD

AGENCY ADDRESS