Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
K9-C23_INST_4-16 4-16
NOTES! Read all instructions before installing any Havis, Inc. products. Use hardware provided with install kit.
TOOLS Needed: Phillips Screw Driver Trim panel removal tool Caulk Gun Standard Socket set Wire Cutters /Crimpers Drill & Drill bits Metric Socket set PARTS & HARDWARE: QTY DESCRIPTION PART # 1 Front bulkhead with sliding door KNM008004 2 Lower “B” pillar bracket KNM006766 2 Upper “B” pillar bracket KNM006767 1 Rear bulkhead KNM006677 1 Rear bulkhead reinforcement bracket KNM006718 1 Floor KNM006582 1 Front floor bracket KNM006580 1 Rear floor bracket KNM006581 1 Ceiling KNM006678 1 Passenger side upper filler KNM006709-PS 1 Driver side upper filler KNM006709-DS 1 Passenger side middle filler (large) KNM006717-PS 1 Passenger side middle filler (small) KNM006716-PS 1 Driver side middle filler (large) KNM006717-DS 1 Driver side middle filler (small) KNM006716-DS 1 Passenger side lower filler KNM006679-PS 1 Driver side lower filler KNM006679-DS 1 Rubber Mat KNM006785 1 Passenger side door panel DP-C23-6A 1 Driver side door panel DP-C23-1A 1 Passenger side hinged window guard WGI-C23-6-K9 1 Driver side hinged window guard WGI-C23-1-K9 1 Dome Light Kit K9-A-106 30 1/4” serrated flange nut GSM30170 30 1/4 x 3/4” Carriage bolt – SS GSM32024 25 1/4 Flat washer - SS GSM31048 21 1/4 x 3/4” Phillips pan head screw - SS GSM34102 4 M6 x 1.0 – 120mm Hex head bolt - SS GSM33747 4 3.5” spacer CM93079 10 #10 x 1/2 Phillips flat head sheet metal screw - SS GSM34150 8 #10 x 1/2 Phillips pan head sheet metal screw – SS GSM34169 18 #10 x 3/4 Phillips pan head sheet metal screw- SS GSM34170 1 Silicone caulk (sealant) PRM97343
K9-C23 INSTALLATION INSTRUCTIONS K9 Kit for 2015 - 2020 CHEVY TAHOE PPV (9C1)
K9-C23_INST_4-16 4-16
K9-C23 Assembly (Door panels and window guards not shown)
KNM008004 Front Bulkhead
KNM006709-DS Driver side Upper filler
KNM006677Rear Bulkhead
KNM006582 Floor
KNM006679-DSDriver side lower filler
KNM006679-PSPassenger side lower filler
KNM006581Rear floor bracket
KNM006678Ceiling
KNM006717-PSPassenger side Large middle filler & KNM006716-PS Passenger side Small middle filler
KNM006717-DS Driver side Large middle filler
KNM006709-PS Passenger side Upper filler
KNM006767 Upper “B” Pillar Bracket
KNM006766 Lower “B” Pillar Bracket
KNM006716-DSDriver side Small middle filler
KNM006580 Front floor bracket Not Shown
CM93079 3.5” Spacers
KNM006718Rear bulkhead reinforcement bracket
K9-A-106Dome Light
K9-C23_INST_4-16 4-16
Remove / unsnap entire door panel from door. (Trim removal tool)
Remove armrest bracket.
(7mm socket)
Disconnect door latch cable and lock pin. Remove speaker. (7mm socket) Note: Carefully wire tie cable and or route for connecting to optional Door
Popper solenoid.
Optional Door Popper solenoid shown. An installer provided bracket is required
for mounting in this recommended location. OEM latch cable attaches
directly to solenoid.
Remove rear passenger door panels first.
Remove screw at bottom of door panel. (7mm socket)
Remove plastic covers behind the paddle handle and armrest handle.
Remove screws. (7mm socket) Note: A small 90° scribe helps to pick
plastic covers off.
Remove window switch from door panel and reattach it to original
plug. Neatly wire tie the speaker wire, switch wire with switch inside
the speaker cavity so it does not interfere with the window
operation. Note: Wrapping switch in a plastic bag will protect against possible exposure to
water.
NOTE: For future reference This photo shows the
recommended location for the optional door popper gas spring
mount. This solid mounting point is between 10” and 11.5” up from the bottom of door skin and 4” to 5” from front edge of door skin.
(just above speaker hole)
Hook top of door panel into rubber window gasket. Center door panel and
drill 1/8” mount holes. Attach with # 10 x 3/4” sheet metal screws.
Note: Prior to this step, the rubber window gasket needs to be removed from the door panel and placed back
onto the door.
K9-C23_INST_4-16 4-16
NOTE: Before closing door, double check the lock and
window operation several times.
See steps 39 – 41 for optional gas spring mounting.
Align the hinge mounting holes to holes in the door panel. Attach hinge
with # 10 x 1/2 Phillips pan head sheet metal screws.
Drill door panel with 3/8” bit for wire grommet. Neatly run optional
fan wiring through door panel.
Coming out the top of the door panel is recommended.
Follow the same installation process for the driver side door.
However, the wires for the optional 10” exhaust fan WGI-FAN need to
be run first.
NOTE: Window guards are shipped flat. On the edge of a work
bench, bend a contour in the middle of the guard so it will fit tight against the window frame.
As of 3/13/15, Tahoe K9 window guards include cutout for fan mount on both
sides. The cutout includes a flat bolt on panel as shown. Optional K9-A-104
includes 10” fan K9-A-301, Fan mount and hardware for mounting
on either side window guard.
With upper mount bracket attached to window guard, mark mounting hole
locations on upper door / window frame. Leave plastic window trim on frame.
Drill 5/32 holes and attach with # 10 x 1/2” flat head sheet metal screws.
Double check the hinge down / window cleaning feature by
removing the four (4) machine screws that hold the guard to the
upper mount bracket.
Mount optional K9-A-104 fan and Fan mount to window guard with 1/4” hardware and spacers as per the instructions provided in the
K9-A-104 kit.
K9-C23_INST_4-16 4-16
Loosely attach floor to brackets with eight (8) 1/4" x 3/4" carriage bolts
and serrated flange nuts.
Carriage bolt heads go on the K9 side of floor.
(floor to rear bracket shown)
Tighten floor mount hardware after all bolts and nuts are in place.
Mount Fan and neatly run and connect Fan wiring.
The optional K9-A-104 kit shown is
sold separately.
NOTE: Before closing door, double check the lock,
window and fan operation several times.
Remove rear passenger seats.
Flip seats forward and remove nuts from seat mount studs. Save Nuts.
(18 mm and 13mm sockets)
Attach front floor bracket to seat mount studs with OEM nuts.
Attach rear floor bracket to seat mount studs with OEM nuts.
.
Note: Run wiring for Dome light, rear fan and other equipment
prior to installing floor.
K9-C23_INST_4-16 4-16
Loosely attach upper filler panel to ceiling with 1/4 x 3/4 Phillips pan
head bolts and flat washers.
Loosely attach upper filler panel to front bulkhead with 1/4 x 3/4 carriage
bolt and serrated flange nut.
Loosely attach large middle filler panel to rear bulkheads with 1/4 x
3/4 carriage bolts and serrated flange nuts.
Install LED dome light as per instructions and hardware included
with the dome light kit.
Loosely attach ceiling to bulkheads with 1/4 x 3/4 Phillips pan head
bolts and flat washers.
Attach upper / long “L” bracket to “B” pillar with M6 x 120mm hex
head bolt and 3.5” spacer. Note: “L” tab goes inward.
Attach lower / short “L” bracket to “B” pillar with M6 x 120mm hex head
bolt and 3.5” spacer. Note: “L” tab goes outward.
Loosely attach rear bulkhead to floor with 1/4 x 3/4 Phillips pan
head bolts and flat washers.
Remove plastic caps on the “B” pillar grab handles.
(top and bottom)
Loosely attach front bulkhead to “B” pillar brackets with 1/4 x 3/4 carriage bolts and serrated flange nuts. Also attach bulkhead to floor 1/4 x 3/4
carriage bolts and serrated flange nuts.
K9-C23_INST_4-16 4-16
Double check, adjust and tighten all hardware as needed.
Neatly silicone / caulk the lower seams to shed water out of vehicle.
Note: The floor is designed to minimize the need for sealant. Caulk (sealant) is
mostly needed where the floor meets the door sill and lower filler panels.
Let silicone dry overnight and place rubber mat inside.
Installation Complete
Mounting for optional door popper gas spring.
As shown in step 8, position the ball mount bracket between 10” and
11.5” up from bottom of door panel. Mark mounting holes and drill K9
door panel and OEM door with 1/8”bit. Attach bracket with supplied sheet metal screws.
Older ball mount bracket shown.
Loosely attach small middle filler panel to upper and lower filler
panels with 1/4 x 3/4 Phillips pan head bolts and flat washers. Tighten all hardware.
Loosely attach lower filler to bulkhead and floor with 1/4 x 3/4 Phillips pan head bolts and
flat washers.
As shown in step 8, position the ball mount bracket between 4” and
5” from edge of door panel. Newer Heavy Duty ball mount
bracket shown.
Example of optional K9-A-102 installed on passenger side of front
bulkhead.
Holes are already included in front bulkhead for gas spring mount. Attach
with supplied hardware. Note: Mount holes may need to be drilled
depending on if you have old or new brackets provided with gas spring kit.