JWEB user documentation

8/7/2019 JWEB user documentation

1/20

J-WEB DOCUMENTATION.

J-WEB INITIAL SETUP WIZARDS.

Introduction

Connect the management device to the services gateway using either of the following

methods: Connect an RJ-45 cable (Ethernet cable) from any one port between ge-0/0/1 andge-0/0/15 on the front panel to the Ethernet port on the management device (workstation or

laptop). After connecting the management device to the services gateway, the DHCP server

process on the services gateway will assign an IP address automatically to the management

device. Ensure that the management device acquires an IP address on the 192.168.1/24

subnet-work (other than 192.168.1.1) from the device. The services gateway functions as a

DHCP server and will assign an IP address to the management device. By default, the DHCP

server is enabled on the L3 VLAN interface, (IRB) vlan.0 (ge-0/0/1 to ge-0/0/15), which is

configured with an IP address of 192.168.1.1/24. When an SRX device services Gateway is

powered on for the first time, it boots using the factory default configuration.

Setup wizards

1. Launch a Web browser on the management device2. Enter http://192.168.1.1 in the URL address field. The J-Web login page is displayed.3. Specify the default user name as root. Do not enter any value in the Password field..

[Type text]


2/20

4. Click Log In. The J-Web Initial Setup page is displayed

5. Click on start>

[Type text]


3/20

6. Configure the basic settings such as Host Name, Domain Name, Root Password andverify Root password: Ensure that you have configured the IP address and root password before you apply the configuration.

NOTE: All fields marked with an asterisk (*) are mandatory

7. Click Next8. Enter the default gateway, DNS servers and domain search

Note: optional field

9. Click Next10.This page enables you to create new VLANs

Note: optional page

[Type text]


4/20

11.Edit an existing VLAN by double-clicking the name or by selecting the row and clickingEdit

12.Moved the ge-0/0/4.0 to available interface and user can able to configure IPV4address

13.Enter the Vlan-id, (range :2-4094)14.Select one or more interfaces in the available Interfaces box, then click the "


5/20

16.This page shows gigabit Ethernet, Fast Ethernet and Vlan interfacesNote: Optional page

17.To edit an interface, double-click it, or select the row and click Edit. To add aninterface, click Add.

18.Select the interface from the drop down list19.Select the DHCP/IP/PPPOE address using radio button20.Select the zone from the drop down list21.Select the services by using check box

[Type text]


6/20

22.Click Save23.Configured interface will appear in configure interface main page

24.Click Next25.This page enables you to select the way that J-Web behaves when you start it.26.Select the option in J-web starting page option27.Select the option in J-web commit options

28.Click Next

[Type text]


7/20

29.This page to set the system time and time zone(Note: Optional page)

30.Click Next31.This page shows the system configuration summary

USER SCENARIO 1: SOFWARE UPGRADE USING THE J-WEB.

Steps:

1. Download the software to local PC

2. Navigate to Maintain > Software> Upload Package page

3. Click on Browse and select the downloaded software

[Type text]


8/20

4. Select reboot options if required and click on Upload and install package button

5. Browser will refresh every 1min to provide updated status and the 1st update will be

available once image is copied to router

6. Upload competion time depends on the platform

7. Click on OK once the process is done or select reboot schedule

[Type text]


9/20

FTP upload

1. Navigate to Maintain > Software> Install package page for FTP upload

2. Provide FTP server and credential information and click on Fetch and install package

button

[Type text]


10/20

3. UI indicates step by step install progress

[Type text]


11/20

4. Click OK to reboot immediately (if reboot is selected ) or schedule a reboot using

hyperlink

Rollback to Alternative package:

1. Navigate to Maintain > Software> Downgrade page (to rollback to alternative

version )

2. Click on Downgrade button and select the hyper link to schedule a reboot

[Type text]


12/20

Note: during reboot connection to the router will be lost hence there wont be any

update in the page status.

[Type text]


13/20

User Scenario 3: J-WEB FW and NAT wizard:

Steps to configure FW using Wizards

FW wizards

32.Navigate to configure > Wizards > Fw_wizards (after initial setup)33.Click on start >

34.click on Add>35.Enter the policy name36.Select the available zone_address for source and destination address and move to

selected zone/address using Up arrow mark37.Select the available applications and move to selected application using Up arrow

mark.38.Select the Action as permit/deny

(Note: All the given fields are mandatory)

[Type text]


14/20

39.Click save, and it will reflect in firewall policy table

[Type text]


15/20

VPN Wizard

1. Navigate to configure > Wizards > VPN_wizards (after initial setup)2. Click on start >

3. Enter VPN name4. Select a security zone for the local private network from the list.5. Add network addresses to identify the local networks for the VPN. Add addresses by

entering them and clicking Add.6. Enter the ST0 interface, number should be between (0-65535)

7. Select a security zone for the interface from the list8. Indicate whether the interface is numbered (an IP address) or unnumbered9. Select an interface for the public network from the lists provided10.Select an interface zone for the public network from the lists provided.11.Indicate the interface type, either static/dynamic

[Type text]


16/20

12.Add remote Gateway Public IP

13.Add IP addresses for the remote private networks and clicking Add.

14.Select the IKE security level15.Select the IKE mode16.Enter IKE preshared key (Ascii)17.Select the IPSec security level18.Select the IPSec forward secrecy19.Select the optional choice VPN monitor, Dead peer Detection

[Type text]


17/20

20.Select the optional field

21. click commit

[Type text]


18/20

[Type text]


19/20

NAT Wizard

1. Navigate to configure > Wizards > NAT_wizards (after initial setup)2. Click on start >

3. Click Add enter rule name4. Indicate whether the rule specifies a zone or an interface for the direction the traffic

comes from5. Select the list and move to the RHS6. Enter a destination address in the form of a host address or a network address.7. Specify the address to use to perform static NAT

[Type text]


20/20

[Type text]

Documents

JWEB user documentation