JRM Inc 2010 CatalogPricing 12-21

12 www.jrmonline.com • email: [email protected] • USA Toll Free (888) 576-7007 • International (336) 354-1243 • Fax (336) 354-1255

MACHINES

Machine 3/8” Mount 1/2” Mount 5/8” Mount 3/4” Mount 7/8” Mount 8mm Mount 12mm Mount 18mm Mount 24mm Mount

Toro Greens Aerator X X X

Toro® ProCore 648 x x x

Toro® ProCore 864/1298 x x x

Toro® ProCore 440/660/880 x x x

Toro® Fairway Aerifier x x

John Deere® 800 x x x

John Deere® 1000 x x



Ryan® GA-24 x x x x

Ryan® GA-30/60 x x x x x

Jacobsen® Aero King 30 x

Jacobsen® Aero King 1224 x

Jacobsen® Performaire 60/80 x x

Coremaster® 6/12 (.725)

Coremaster® Precision 1200/1560 (.835)

VERTI-DRAIN® 7007/700/7H/7110/7113/7117/7120/7626 x x x

VERTI-DRAIN® 7212/7215/7316/7416/7521/7526 x x x

Soil Reliever® (SR) 48/54/72/75HD/80 x x

Wiedenmann® Terra Spike GXi/XF/XD/XP (Dimple) (Dimple) (Conical screw)

Wiedenmann® Greens Terra Spike (Dimple) (Dimple) (Conical screw)

The mounting diameter of your machine, and the proper length of tine needed for your aerification are the two most important factors you should consider when selecting the correct tine.

Located below is a list of the most popular machines from Toro®, John Deere®, Jacobsen®, Coremaster®, Ryan®, VERTI-DRAIN®, Soil Reliever®, and Wiedenmann®, and the corresponding mounting diameter options available for each machine. The smaller mounts (1/2”, 3/8”) represent the Quad blocks used for our Quad line and solid/venting tines. Remember that Coremaster® uses a unique mount size, and we also offer CROSSTINES® and solid tines to fit these machines. Please take note of the unique mounts for the Wiedenmann® machines as well. The machines require the 8mm, 12mm dimple mount, or the 1:10 conical screw mount. Please consult your machine manual before choosing a tine. This chart will help you determine what mounts can fit on your specific machine to determine what type of options you have when selecting a tine.Also pay attention to a tine’s length. All machines are different. John Deere® machines can easily take a tine longer than 6 inches, but Ryan® has a recommended tine height of 4.5 inches. So if you plan to use a tine longer than the recommended height, please keep a close eye on the tines during aerification to make sure they are not creating a plowing effect in your soil.

13www.jrmonline.com • email: [email protected] • USA Toll Free (888) 576-7007 • International (336) 354-1243 • Fax (336) 354-1255

CONVENTIONAL CORINg TINES

JRM offers a wide variety of conventional coring tine options to fit all of your aeration needs. We have standard tines made to fit most John Deere®, Toro®, Coremaster®, Jacobsen®, and Ryan® aeration machines.

We offer conventional coring tines in two styles, Premium and DILLENNIUM®. A premium tine is identical to the corresponding DILLENNIUM® tine in all respects except that it does not have our trademarked carbide tip. Compared to a typical OEM tine, a premium tine should deliver a minimum 300 to 400% performance increase. This is due to the design and quality of steel used. A DILLENNIUM® tine will give a 700+ performance increase as compared to a typical OEM tine. DILLENNIUM® tines are available in side-eject and top-eject versions, and all JRM coring tines are made of the finest available high-carbon alloy steel.

The longer use-life of a DILLENNIUM® tine will significantly reduce “down time” and also save on overall course maintenance costs. The most significant advantage of these conventional DILLENNIUM® tines may be that every core, from green 1 to 18, will be exactly the same length. This assures that the water and nutritional uptake is consistent from green to green. Course management therefore becomes much easier once you adopt JRM DILLENNIUM® tines as your standard coring tine. JRM offers a “use” warranty in addition to a quality warranty. You can view our entire warranty program on Page 44 of this catalog.

When selecting a tine for your Toro® and John Deere® aerifier, make sure you carefully check the mounting diameter and length to make your choices. With the introduction of the Toro® ProCore series aerifiers, both John Deere and Toro® aerifiers can accept a tine longer than five inches. For this reason, JRM offers a wide variety of longer tines suitable for these machines with additional core depth. Please note, that if you have an older model Toro® greens aerifier, any tine longer than five inches may not work on your machine and may cause turf damage.

Coremaster® tines are unique since they require a mounting diameter that is different from all other brands. Therefore Coremaster® tines are not interchangeable with tines from other manufacturers. The unique mount size has no effect on the tine design, quality, or use-life and indeed, all other qualities of the tines are identical to comparable JRM coring tines. CROSSTINES™ and quad tines are also available to fit Coremaster® machines.

The JRM Ryan® replacement parts are made to fit the GA 24, GA30, and GA60 aerifiers. In addition to our coring tines, many of the quads, solid tines, and CROSSTINES™ will fit all three machines. Please carefully check the mounting diameters and lengths to make sure the tines you order are correct. Most Ryan® machines will not accept a length longer than 4.5 inches. However, the GA60 will accept a wide variety of JRM tines specifically designed for your fairways.

JRM makes two DILLENNIUM® tines specifically designed for use on Jacobsen® machines. Since their introduction, these two tines have gained wide acceptance due to their exceptional cost/use-life. These tines should outlast comparably priced tines by a factor of two or three to one. We are also making these tines out of solid stock now and they will no longer have a welded shank.

Finally, our DILLENNIUM® lite tines are made of the same high-quality alloy steel of which our flagship DILLENNIUM® tines are made, but they have a slightly thinner wall. These tines are for the superintendent who demands the very finest possible cut and core quality. The use-life of these tines are not as long as our standard DILLENNIUM® tines, but it will produce the finest coring job available today and will certainly outlast other coring tines. They are especially useful on new or very soft greens with high sand or thatch content where aerification is problematic. They are more likely to pull a core, and the core itself is of higher quality with less compaction. All DILLENNIUM® lite tines are top-ejects, and cost less than a standard JRM DILLENNIUM® coring tine.

1RS625101

1C500501

1TS750502

1T625505

1TS500105

1D500103

1DS500101

1DS625504

1J500501

1J625501

1DL500502

1DL625503

1TS625106

1TS625506

1TS750102

1R500102

1D500104

1D750501

1DS750501

1T625102


CONVENTIONALCORINg TINES John Deere®Replacement parts for John Deere®

Part No. JRM Description Length Mount Diameter I.D. Tapered O.D. Wall Price

1DS375503 DILLENNIUM® 3/8" side-eject tine 4.5" 5/8" .270" .425" .072" $12.15

1D375101 Premium 3/8" top-eject tine 5.5" 3/4" .285" .429" .072" $4.50

1DS375101 Premium 3/8" side-eject tine 5.5" 3/4" .285" .429" .072" $5.35

∞ 1DS375801 INFINITY 3/8" side-eject tine 5.5" 3/4" .285" .429" .072" $12.35

1DS375504 DILLENNIUM® 3/8" side-eject tine 5" 3/4" .270" .425" .072" $12.15



1D500503 DILLENNIUM® 1/2" top-eject tine 4.5" 5/8" .400" .525" .072" $10.85



1D500504 DILLENNIUM® 1/2" top-eject tine 5" 3/4" .400" .525" .072" $10.85







1D500105 Premium 1/2" top-eject tine 6" 3/4" .390" .550" .072" $4.50

1DS500105 Premium 1/2" side-eject tine 6" 3/4" .390" .550" .072" $5.35

∞ 1DS500805 INFINITY 1/2" side-eject tine 6" 3/4" .390" .550" .072" $12.35







1D625504 DILLENNIUM® 5/8" top-eject tine 5" 3/4" .485" .633" .072" $10.85









∞ 1DS625805 INFINITY 5/8" side-eject tine 6" 3/4" .490" .655" .072" $12.35







John Deere® is a registered trademark of John Deere Co., Research Triangle Park, NC 27709

∞ INFINITY Tines


CONVENTIONALCORINg TINES Toro®

Replacement parts for Toro® Part No. JRM Description Length Mount Diameter I.D. Tapered O.D. Wall Price

1TS375501 DILLENNIUM® 3/8" side-eject tine 5" 3/4" .270" .425" .072" $12.15

1T500101 Premium 1/2" top-eject tine 4.75" 3/4" .385" .560" .072" $4.05

∞ 1T500801 INFINITY 1/2" top-eject tine 4.75" 3/4" .385" .560" .072" $9.85

1T500501 DILLENNIUM® 1/2" top-eject tine 5" 3/4" .400" .525" .072" $10.85



1TS500102 Premium 1/2" side-eject tine 5.5" 3/4" .390" .550" .072" $5.35

1T500502 DILLENNIUM® 1/2" top-eject tine 5.75" 3/4" .400" .525" .072" $12.15

1TS500502 DILLENNIUM® 1/2" side-eject tine 5.75" 3/4" .400" .525" .072" $13.35

1T500105 Premium 1/2" top-eject tine 6" 3/4" .390" .550" .072" $4.50

1TS500105 Premium 1/2" side-eject tine 6" 3/4" .390" .550" .072" $5.35




∞ 1T625801 INFINITY 5/8" top-eject tine 4.75" 3/4" .480" .650" .072" $9.85

1T625501 DILLENNIUM® 5/8" top-eject tine 5" 3/4" .485" .633" .072" $10.85


















TORO® is a registered trademark of The Toro Company, Bloomington, MN 55420

∞ INFINITY Tines


CONVENTIONALCORINg TINES Ryan®/Coremaster®/Jacobsen®

Replacement parts for Ryan® Part No. JRM Description Length Mount Diameter I.D. Tapered O.D. Wall Price

1RS375501 DILLENNIUM® 3/8" side-eject tine 4.5" 5/8" .270" .425" .072" $12.15


1R500101 Premium 1/2" top-eject tine 4.25" 5/8" .380" .540" .072" $4.05

1R500501 DILLENNIUM® 1/2" top-eject tine 4.5" 5/8" .350" .525" .072" $10.85






1RS625101 Premium 5/8" side-eject tine 4.25" 3/4" .480" .650" .072" $5.35



Replacement parts for Coremaster® Part No. JRM Description Length Mount Diameter I.D. Tapered O.D. Wall Price

1CS375501 DILLENNIUM® 3/8" side-eject tine 4.75" .725" .270" .425" .072" $12.15

1C500101 Premium 1/2" top-eject tine 4.5" .725" .390" .550" .072" $4.05

1C500501 DILLENNIUM® 1/2" top-eject tine 4.75" .725" .350" .525" .072" $10.85

1CS500501 DILLENNIUM® 1/2" side-eject tine 4.75" .725" .350" .525" .072" $12.15

1C625101 Premium 5/8" top-eject tine 4.5" .835" .495" .650" .072" $4.05

1C625501 DILLENNIUM® 5/8" top-eject tine 4.75" .835" .485" .633" .072" $10.85

2T625103 Solid 5/8" tine for Coremaster® 5" .725" N/A .625” Solid $4.40

2CX500103 Premium CROSSTINE® 1/2” rib for Coremaster® 4.6" .725" N/A .500" Solid $8.36

2CX500503 DILLENNIUM® CROSSTINE® 1/2” rib for Coremaster® 4.8" .725" N/A .500" Solid $12.29

Replacement parts for Jacobsen® Part No. JRM Description Length Mount Diameter I.D. Tapered O.D. Wall Price

1J500501 DILLENNIUM® 1/2" side-eject tine 6.25" 5/8" .350" .525" .072" $12.65

1J625501 DILLENNIUM® 5/8" side-eject tine 6.25" 5/8" .480" .633" .072" $14.85

Coremaster® is a registered trademark of GREENCARE®, Caringbah, NSW 2229 Australia

Ryan® is a registered trademark of TEXTRON Turf Care and Specialty Products, Racine, WI 53403

Jacobsen® is a registered trademark of TEXTRON Turf Care and Specialty Products, Racine, WI 534031J500501 replaces Jacobsen® AeroKing 1/2” Side Eject1J625501 replaces Jacobsen® AeroKing 5/8” Side Eject


CONVENTIONALCORINg TINES DILLENNIUM® Lite Tines/The SharkTM

DILLENNIUM® Lite Tines Part No. JRM Description Length Mount Diameter I.D. Tapered O.D. Wall Price

1DL500501 DILLENNIUM® Lite 1/2" tine 4.5" 5/8" .406" .543" .055" $9.50

1DL500502 DILLENNIUM® Lite 1/2" tine 5" 3/4" .406" .543" .055" $9.50






The SharkTM Self-defense Key Chain Part No. JRM Description Length Color Price

9S500101 Self-defense Key Chain 5" Black $12.00

9S500102 Self-defense Key Chain 5" Pink $12.00

The Shark™ is a self-protection tool that proves to be a fistful of bite!

Designed by martial artist and self-defense specialist, Michael Joyce, of the Chen Center in Winston-Salem, N.C., The Shark™ was engineered and now manufactured by JRM, Inc.

The Shark was designed as a keychain, but it has a dual purpose as a means of self-protection. It is easily concealable, lightweight, and extremely durable.

The Shark™ can be a fearsome tool that can literally take a bite and fight out of your attacker. For additional information, go to chencenterstore.com.

The Shark™ is available in black or pink.

The Shark™ is to be used for self-protection only! Any other uses besides self-defense is strictly prohibited. The designer [Michael Joyce], ChenCenter, JRM, Inc., and associates accept no responsibility for injuries (including death) sustained or inflicted, or damage of any sort that may occur as a result of using this self-defense tool.

Our DILLENNIUM® lite tines are made of the same high-quality alloy steel of which our flagship DILLENNIUM® tines are made, but they have a slightly thinner wall. These tines are for the superintendent who demands the very finest possible cut and core quality. The use-life of these tines are not as long as our standard DILLENNIUM® tines, but it will produce the finest coring job available today and will certainly outlast other coring tines. They are especially useful on new or very soft greens with high sand or thatch content where aerification is problematic. They are more likely to pull a core, and the core itself is of higher quality with less compaction. All DILLENNIUM® lite tines are top-ejects, and cost less than a standard JRM DILLENNIUM® coring tine.

1DL500501


QUAD TINES

Quad tines are the smallest and least invasive coring tines available. Our quad tines are milled from a single rod for enhanced strength and longevity, and it also comes with a variable wall thickness for longer life. Quad tines are ideal for use during times of stress, or when a short grow-in period is desired. They may be used in standard mounting blocks (3/4”), or in the closely spaced “Quad Block” containing six or seven tines. The DILLENNIUM® quad provides at least twice the use-life compared to the premium quad.

Our standard quads are some of the smallest coring tines on the market, and are extremely useful when you are seeking a very minimal core. The SuperQuad™ tines come with a slightly larger outside diameter than our standard quad, and they have quickly been adopted by many superintendents as their “tine of choice” because of the exceptionally fine core it produces and reduced grow-in time required.

When JRM created the Magnum Quad™, the family of tines became an instant success. Overnight, customers were able to address the many unique needs associated with the new hybrid bent grasses. The Magnum Quad™ was specifically designed for de-thatching and maximizing nutrient/gas exchange. This was achieved with closer spacing and a larger core diameter. The DILLENNIUM® Magnum Quad™ offers the same robust tine as the premium, but comes with an enhanced carbide tip. This tip maximizes the value of the tine by offering consistent core depth and far superior quality. A DILLENNIUM® Magnum Quad™ should outlast a premium Magnum Quad™ by 200 to 300%.

The Magnum Quad Plus™ tines are the largest quad tine that we offer. After the quick success of the Magnum Quad introduced in 2004, we received requests for a new and even larger quad tine that would give greater coverage. The Mag Plus™ tines have an outside diameter of .612 inches for maximum coverage. No other quad offers a core as large with a possibility of 1x1 inch spacing. All Mag Quad Plus™ tines are made of 4140, high-carbon, alloy steel for strength and longevity.

At JRM, we are aware that every manufacturer has a different method of measuring the outside diameter of its product. We want to clarify how we measure ours, especially with our tapered ODs for our quad line.

We determine our OD based on the initial entry of the tine into the soil. Although the OD of the tine is larger toward the mount, and that width may make the hole larger initially, the hole will always shrink back down to the size of initial entry. We measure our OD at the tip right after we cut the stock for the part. It may seem deceiving by looking at the part with the naked eye, but after many field studies, we’ve determined this is the most accurate way to measure the outside diameter.

1Q250103

1Q250503

1QT250503

1QT250101

1Q250106

1QT375105

1QT375511

1Q500502

1Q500103

1Q500106

1QT500105

1Q500508

1Q375505

1Q375103

1QT450104

1Q450104

1QT500501

1QT575104

1Q575102

1QT625103


Part No. JRM Description Length Mount Diameter I.D. Tapered O.D. Wall Price1Q250104 Premium 1/4" Quad Tine 4.20" 5/16" .240" .330" .065" $5.20 1Q250504 DILLENNIUM® 1/4" Quad Tine 4.325" 5/16" .240" .327" .065" $10.95 1Q250101 Premium 1/4" Quad Tine 3.5" 3/8" .240" .330" .065" $4.95

*1QT250101 Premium 1/4" Quad Tine (with Toro® shank) 3.5" 3/8" .240" .330" .065" $4.95 1Q250501 DILLENNIUM® 1/4" Quad Tine 3.625" 3/8" .240" .327" .065" $9.85

*1QT250501 DILLENNIUM® 1/4" Quad Tine (with Toro® shank) 3.625" 3/8" .240" .327" .065" $9.85 1Q250105 Premium 1/4" Quad Tine 4.5" 3/8" .240" .330" .065" $5.75

*1QT250105 Premium 1/4" Quad Tine (with Toro® shank) 4.5" 3/8" .240" .330" .065" $5.75

∞ *1QT250805 INFINITY 1/4" Quad Tine (with Toro® shank) 4.5" 3/8" .240" .330" .065" $9.951Q250505 DILLENNIUM® 1/4" Quad Tine 4.625" 3/8" .240" .327" .065" $10.95

*1QT250505 DILLENNIUM® 1/4" Quad Tine (with Toro® shank) 4.625" 3/8" .240" .327" .065" $10.95 1Q250103 Premium 1/4" Quad Tine 5" 3/8" .240" .330" .065" $6.00

∞ 1Q250803 INFINITY 1/4" Quad Tine 5" 3/8" .240" .330" .065" $10.50*1QT250103 Premium 1/4" Quad Tine (with Toro® shank) 5" 3/8" .240" .330" .065" $6.00

∞ *1QT250803 INFINITY 1/4" Quad Tine (with Toro® shank) 5" 3/8" .240" .330" .065" $10.501Q250503 DILLENNIUM® 1/4" Quad Tine 5.125" 3/8" .240" .327" .065" $11.50

*1QT250503 DILLENNIUM® 1/4" Quad Tine (with Toro® shank) 5.125" 3/8" .240" .327" .065" $11.50 1Q250102 Premium 1/4" Quad Tine 4" 1/2" .240" .330" .065" $5.20 1Q250502 DILLENNIUM® 1/4" Quad Tine 4.125" 1/2" .240" .327" .065" $10.95 1Q250106 Premium 1/4" Quad Tine 4.5" 1/2" .240" .330" .065" $5.75 1Q250506 DILLENNIUM® 1/4" Quad Tine 4.625" 1/2" .240" .327" .065" $10.95 1Q250107 Premium 1/4" Quad Tine 4" 5/8" .240" .330" .065" $5.20 1Q250507 DILLENNIUM® 1/4" Quad Tine 4.125" 5/8" .240" .327" .065" $10.95

* All “QT” parts have a shortened shank designed for the Toro ProCore® Series 648 aerifier ∞INFINITY Tines

Standard Quads

STANDARD QUADS/SUPER QUADTM TINES

Part No. JRM Description Length Mount Diameter I.D. Tapered O.D. Wall Price1Q375100 Premium 3/8" SuperQuadTM Tine 3.5" 3/8" .335" .460" .072" $6.30

*1QT375100 Premium 3/8" SuperQuadTM Tine (with Toro® shank) 3.5" 3/8" .335" .460" .072" $6.30 1Q375500 DILLENNIUM® 3/8" SuperQuadTM Tine 3.625" 3/8" .320" .400" .072" $10.40

*1QT375500 DILLENNIUM® 3/8" SuperQuadTM Tine (with Toro® shank) 3.625" 3/8" .320" .400" .072" $10.40 1Q375105 Premium 3/8" SuperQuadTM Tine 4.5" 3/8" .335" .460" .072" $7.40

∞ 1Q375805 INFINITY 3/8" SuperQuadTM Tine 4.5" 3/8" .335" .460" .072" $10.50*1QT375105 Premium 3/8" SuperQuadTM Tine (with Toro® shank) 4.5" 3/8" .335" .460" .072" $7.40

∞ *1QT375805 INFINITY 3/8" SuperQuadTM Tine (with Toro® shank) 4.5" 3/8" .335" .460" .072" $10.501Q375505 DILLENNIUM® 3/8" SuperQuadTM Tine 4.625" 3/8" .320" .400" .072" $11.50

*1QT375505 DILLENNIUM® 3/8" SuperQuadTM Tine (with Toro® shank) 4.625" 3/8" .320" .400" .072" $11.50 1Q375111 Premium 3/8" SuperQuadTM Tine 5" 3/8" .335" .460" .072" $7.65

*1QT375111 Premium 3/8" SuperQuadTM Tine (with Toro® shank) 5" 3/8" .335" .460" .072" $7.65

∞ *1QT375811 INFINITY 3/8" SuperQuadTM Tine (with Toro® shank) 5" 3/8" .335" .460" .072" $11.051Q375511 DILLENNIUM® 3/8" SuperQuadTM Tine 5.125" 3/8" .320" .400" .072" $12.05

*1QT375511 DILLENNIUM® 3/8" SuperQuadTM Tine (with Toro® shank) 5.125" 3/8" .320" .400" .072" $12.05 1Q375106 Premium 3/8" SuperQuadTM Tine 4.5" 12mm .335" .460" .072" $7.40 1Q375506 DILLENNIUM® 3/8" SuperQuadTM Tine 4.625" 12mm .320" .400" .072" $11.50 1Q375101 Premium 3/8" SuperQuadTM Tine 3.5" 1/2" .335" .460" .072" $6.30 1Q375501 DILLENNIUM® 3/8" SuperQuadTM Tine 3.625" 1/2" .320" .400" .072" $10.40 1Q375102 Premium 3/8" SuperQuadTM Tine 4.5" 1/2" .335" .460" .072" $7.40 1Q375502 DILLENNIUM® 3/8" SuperQuadTM Tine 4.625" 1/2" .320" .400" .072" $11.50 1Q375103 Premium 3/8" SuperQuadTM Tine 4.5" 5/8" .335" .460" .072" $7.40 1Q375503 DILLENNIUM® 3/8" SuperQuadTM Tine 4.625" 5/8" .320" .400" .072" $11.50 1Q375104 Premium 3/8" SuperQuadTM Tine 4.5" 3/4" .335" .460" .072" $7.40 1Q375504 DILLENNIUM® 3/8" SuperQuadTM Tine 4.625" 3/4" .320" .400" .072" $11.50

Super QuadsTM


Part No. JRM Description Length Mount Diameter I.D. Tapered O.D. Wall Price

1Q450104 Premium Magnum Lite™ Tine 4.5" 3/8" .350" .480" .065" $7.95

*1QT450104 Premium Magnum Lite™ Tine (with Toro® shank) 4.5" 3/8" .350" .480" .065" $7.95




* All “QT” parts have a shortened shank designed for the Toro ProCore® Series 648 aerifier ∞ INFINITY Tines

Magnum LiteTM Tines

Part No. JRM Description Length Mount Diameter I.D. Tapered O.D. Wall Price1Q500110 Premium 1/2" Magnum Quad™ Tine 6.5" 5/16" .400" .525" .072" $8.75

1Q500510 DILLENNIUM® 1/2" Magnum Quad™ Tine 6.625" 5/16" .403" .504" .072" $12.55

1Q500105 Premium 1/2" Magnum Quad™ Tine 3.5" 3/8" .400" .525" .072" $7.10

*1QT500105 Premium 1/2" Magnum Quad™ Tine (with Toro® shank) 3.5" 3/8" .400" .525" .072" $7.10


*1QT500505 DILLENNIUM® 1/2" Magnum Quad™ Tine (with Toro® shank) 3.625" 3/8" .403" .504" .072" $11.20



∞ *1QT500801 INFINITY 1/2" Magnum Quad™ Tine (with Toro® shank) 4.5" 3/8" .400" .525" .072" $10.75




∞ *1Q500803 INFINITY 1/2" Magnum Quad™ Tine 5.5" 3/8" .400" .525" .072" $11.30


∞ *1QT500803 INFINITY 1/2" Magnum Quad™ Tine (with Toro® shank) 5.5" 3/8" .400" .525" .072" $11.30



1Q500109 Premium 1/2" Magnum Quad™ Tine 4.5" 12mm .400" .525" .072" $7.95

1Q500509 DILLENNIUM® 1/2" Magnum Quad™ Tine 4.625" 12mm .403" .504" .072" $11.60




∞ 1Q500802 INFINITY 1/2" Magnum Quad™ Tine 4.5" 1/2" .400" .525" .072" $10.75










Premium/DILLENNIUM® Magnum Quad™ Tines

MAgNUM LITETM/DILLENNIUM® MAgNUM QUADTM TINES


MAgNUM QUAD PLUS™ TINES

Part No. JRM Description Length Mount Diameter I.D. Tapered O.D. Wall Price1Q575103 Premium Mag Quad Plus™ Tine 4.5" 3/8" .470" .595" .063" $8.20

*1QT575103 Premium Mag Quad Plus™ Tine (with Toro® shank) 4.5" 3/8" .470" .595" .063" $8.20

1Q575503 DILLENNIUM® Mag Quad Plus™ Tine 4.5" 3/8" .465" .597" .063" $12.05

*1QT575503 DILLENNIUM® Mag Quad Plus™ Tine (with Toro® shank) 4.5" 3/8" .465" .597" .063" $12.05

1Q5785108 Premium Mag Quad Plus™ Tine 5.30" 3/8" .470" .595" .063" $8.35



*1QT575508 DILLENNIUM® Mag Quad Plus™ Tine (with Toro® shank) 5.30" 3/8" .465" .597" .063" $12.20

1Q575104 Premium Mag Quad Plus™ Tine 6" 3/8" .470" .595" .063" $8.75

∞ *1Q575804 INFINITY Mag Quad Plus™ Tine 6" 3/8" .470" .595" .063" $11.55

*1QT575104 Premium Mag Quad Plus™ Tine (with Toro® shank) 6" 3/8" .470" .595" .063" $8.75

∞ *1QT575804 INFINITY Mag Quad Plus™ Tine (with Toro® shank) 6" 3/8" .470" .595" .063" $11.55

1Q575504 DILLENNIUM® Mag Quad Plus™ Tine 6" 3/8" .465" .597" .063" $12.55

*1QT575504 DILLENNIUM® Mag Quad Plus™ Tine (with Toro® shank) 6" 3/8" .465" .597" .063" $12.55

1Q575109 Premium Mag Quad Plus™ Tine 4.5" 12mm .470" .595" .063" $8.20

1Q575509 DILLENNIUM® Mag Quad Plus™ Tine 4.5" 12mm .465" .597" .063" $12.05

1Q575105 Premium Mag Quad Plus™ Tine 6" 12mm .470" .595" .063" $8.75

1Q575505 DILLENNIUM® Mag Quad Plus™ Tine 6" 12mm .465" .597" .063" $12.55


∞ 1Q575802 INFINITY Mag Quad Plus™ Tine 4.5" 1/2" .470" .595" .063" $11.05


1Q575107 Premium Mag Quad Plus™ Tine 5" 1/2" .470" .595" .063" $8.35

1Q575507 DILLENNIUM® Mag Quad Plus™ Tine 5" 1/2" .465" .597" .063" $12.20





∞ *1QT625803 INFINITY Mag Quad Plus™ Tine (with Toro® shank) 4.5" 3/8" .510" .640" .063" $11.65


Magnum Quad Plus™ Tines

Mike Hard, Maintenance tecHnician, alpine country club in aMerican Fork, utaH“I initially ordered Jacobsen® [replacement] bedknives, and JRM is so much cheaper, and they hold up a lot longer too. And with the Toro’s [bedknives] that I’ve ordered, the price is more competitive, but the quality is much better with JRM.”__________________________________________________________________________________________________

rex Floyd, service Manager, nortH ridge country club in raleigH, nortH carolina“I have always been a staunch OEM guy, but after touring the JRM factory, I was so impressed with the operation that I had to give the [DUARANIUM-801®] bedknives a shot. To meet Jim (Merritt, JRM, Inc. President/CEO) and witness everything that goes into making bedknives from the coining process to the way they cut the steel, they look at every aspect of the bedknife to make it better. I see now why they can boast making a superior product.”__________________________________________________________________________________________________

dan lanning, Maintenance tecHnician, capital city club @ crabapple and brookHaven in georgia“With the JRM bedknives, I can set them up at .120” and get them right out on the course. When I get the mowers back in the shop, I don’t have to do any backlapping. I just grind them up and get them back out on the course. Our superintendent likes to keep our greens lean and mean. That would be a much tougher task without a JRM bedknife.”

Satisfied Customers* All “QT” parts have a shortened shank designed for the Toro ProCore® Series 648 aerifier ∞ INFINITY Tines

Documents

JRM Inc 2010 CatalogPricing 12-21