Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
62 IN
48 IN
FLUTES LYDIAN ARRAYRemote Installation Guide
SHOWN ARE EXAMPLES OF CONFIGURATION POSSIBILITIES. SPECIFIC FIXTURE CONFIGURATION MAY VARY.
1
WARNING
A LICENSED ELECTRICIAN SHOULD PERFORM INSTALLATION IN ACCORDANCE WITH THE NATIONAL ELECTRIC CODE (NEC) AND RELEVANT LOCAL CODES.
DISCONNECT MAIN POWER AT THE SOURCE PRIOR TO INSTALLATION.
INSTRUCTIONS MEANT FOR A REMOTE CLASS 2 DRIVER.
FIGURE 1A
FIGURE 1
FIGURE 1A
FIGURE 1A
End cap
Slide sections into each other to connect
Module
FIGURE 1C
FIGURE 1B
Quick-disconnect
FIGURE 1C
M4 Screw
Locking washer
STEP 1: JOINING FIXTURE SECTIONS
Remove the end caps from modules as shown in figure 1A by pulling them off.A.Connect the sections using the dovetail feature in the modules as shown in figure 1A.B.Connect the quick-disconnect switch between the two sections of the fixture as shown in figure 1B.C.Secure the sections of the fixture together using provided M4 screw and locking washer as shown in figure 1C.D.Reinstall the caps on the modules.E.
The two sections of the fixture can be joined following the instruction below as seen in illustrations above.
FLUTES LYDIAN ARRAY INSTALLATION GUIDE 2
WWW.JUNIPER-DESIGN.COM | [email protected] | +1 347 799-2915 | 157 WATER STREET SOUTHINGTON, CT 06489
JUNCTION BOX MOUNTED
FOR FIXTURES WIRED TO A JUNCTION BOX.
SEE STEP 3A FOR DETAILED INSTALLATION AND WIRING INFORMATION.
FIGURE 3
CEILING MOUNTED
FOR FIXTURE MOUNTED DIRECTLY TOTHE CEILING.
SEE STEP 3B FOR DETAILED INSTALLATION AND WIRING INFORMATIONBLOCKING IS RECOMMENDED FOR DRYWALL MOUNTING.
FIGURE 4
47 12 "OR
19 34 "OR
8""
34 34 "
62 12 "
115
" MAX
FIGURE 2
A B
POWER FEED OPTIONS
STEP 2: MARK MOUNTING POINTS
POWERED CANOPY IS USED TO SUSPEND AND POWER THE FIXTURE (SEE POWER FEED OPTIONS).
NON-POWERED CANOPY IS USED TO SUSPEND THE FIXTURE.
KEY
A
B
Carefully mark the mounting points with a pencil or marker, using the spacing in Figure 1. It is highly recommended to use a laser alignment/ measuring tool to ensure that mounting parts are properly distanced and fall on a straight line.
FLUTES LYDIAN ARRAY INSTALLATION GUIDE 3
WWW.JUNIPER-DESIGN.COM | [email protected] | +1 347 799-2915 | 157 WATER STREET SOUTHINGTON, CT 06489
A
Cover plate
Set screw
CanopyFIGURE 5
A
1/8" IPS nut
1/8" IPS nut
1/8" IPS x 1" length threaded nipple
Top cap
FIGURE 6
Crossbar
WasherWood screw
Top capCover plate
B
Set screw
Canopy
B
Top cap
Press the safety nut upwards and hold to pass aircraft cable through the gripper
A B
Bottom cap
Power cordfrom fixtureCanopy
A
Set screw
Cap screw
3 4
Loosen cap screw in bottom cap to release the bottom cap. Pass power cord from fixture through the cap and canopy as shown. Adjust the length of power cord to adjust fixture's drop height. Tighten set screw after adjusting power cord length. Attach bottom cap by tightening the cap screw.Make sure bottom cap and canopy are aligned properly before securing cap screw.
STEP 3A: JUNCTION BOX COVER PLATE INSTALLATION INSTRUCTIONS
Remove set screws from canopy to release top cap.
1 2
Attach the crossbar to the junction box using provided screws.
Using provided wood screw and washer, connect the top cap and provided cover plate to ceiling. Wood screws are provided for default installation. Alternate screws may be used at the recommendation of an electrician. Blocking is recommended for drywall mounting.
Partly loosen safety nut on cable gripper. Feed aircraft cables through the grippers as shown above. Keep the safety nut on gripper pressed to pass aircraft cable through the gripper. Release the safety nut to hold the aircraft cable in position. Do not cut extra power and aircraft cables until desired suspension height is achieved. Tighten the safety nut after completing adjustment.
5
FIGURE 7
FIGURE 9
FIGURE 8
Remove set screws from canopy to release top cap. Install cover plate on the top cap as shown.
Pass low voltage wires from junction box through cross bar and through 1/8IPS nipple attached to cover plate as shown. Screw 1/8IPS nipple into the crossbar to connect cover plate to crossbar.
FLUTES LYDIAN ARRAY INSTALLATION GUIDE 4
WWW.JUNIPER-DESIGN.COM | [email protected] | +1 347 799-2915 | 157 WATER STREET SOUTHINGTON, CT 06489
Set screw
B
BA
Set screw
FIGURE 11
A
Low voltage wires from LED driver
REMOTE LED
DRIVER
OU
TPU
TAC - NEUTRAL
AC - LINEIN
PUT
N
L
-
+
+ 24VDC lead from remote driver
White lead (+)from fixture
Silver Shielding (-) from fixture
- 24VDC lead from remote driver
FIGURE 10
A
FIGURE 12
Adjust power and aircraft cable length as needed to adjust the drop height and to level the fixture. Tighten the safety nut after completing adjustment.
6 7
Connect wires according to diagram (wire nuts provided). Wires to and from the driver are not included.
8
Use set screws (removed in first instruction) to connect canopy to top cap.
Push wires inside the canopy and use set screws (removed in first instruction) to connect canopy to cover plate.
FLUTES LYDIAN ARRAY INSTALLATION GUIDE 5
WWW.JUNIPER-DESIGN.COM | [email protected] | +1 347 799-2915 | 157 WATER STREET SOUTHINGTON, CT 06489
Wires from remote driver
Washer
Wood screw
Top capA
FIGURE 14
Top cap
Set screw
Canopy
Press the safety nut upwards and hold to pass aircraft cable through the gripper
A B
Washer
Wood screw
Top capB
Bottom cap
Power cordfrom fixture
Canopy
A
Set screw
Cap screw
Cover plate
Set screw
CanopyA
1/8" IPS nut
1/8" IPS nut
1/8" IPS x 1" length threaded nipple
Top cap
1 2
3
4
STEP 3B: CEILING MOUNTING INSTALLATION INSTRUCTIONS
Loosen cap screw in bottom cap to release the bottom cap. Pass power cord from fixture through the cap and canopy as shown. Adjust the length of power cord to adjust fixture's drop height. Tighten set screw after adjusting power cord length. Attach bottom cap by tightening the cap screw.Do not cut extra power cable before making sure the its length is suitable for fixture's drop height.Make sure bottom cap and canopy are aligned properly before securing cap screw.
FIGURE 16
Remove set screws from canopies to release top cap.
FIGURE 13Pass low voltage wires from the remote driver through the A.smaller hole in the top cap. Using provided wood screw and washer, connect the top cap to ceiling.Using provided wood screw and washer, connect the top cap B.to ceiling.
Wood screws are provided for default installation. Alternate screws may be used at the recommendation of an electrician. Blocking may be required.
FIGURE 15
Partly loosen safety nut on cable gripper. Feed aircraft cables through the grippers as shown above. Keep the safety nut on gripper pressed to pass aircraft cable through the gripper. Release the safety nut to hold the aircraft cable in position. Do not cut extra power and aircraft cables until desired suspension height is achieved. Tighten the safety nut after completing adjustment.
FLUTES LYDIAN ARRAY INSTALLATION GUIDE 6
WWW.JUNIPER-DESIGN.COM | [email protected] | +1 347 799-2915 | 157 WATER STREET SOUTHINGTON, CT 06489
CARE INSTRUCTIONS
Gently wipe with a damp cloth to remove dirt, dust, and fingerprints.
Do not use any chemical cleaning solution.
Use indoors only.
Low voltage wires from LED driverREMOTE
LED DRIVER
OU
TPU
T
AC - NEUTRAL
AC - LINEIN
PUT
N
L
-
+
+ 24VDC lead from remote driver
White lead (+)from fixture
Silver Shielding (-) from fixture
- 24VDC lead from remote driver
Connect wires according to diagram (wire nuts provided). Wires to and from the driver are not included.
FIGURE 17
A
Set screw
A
FIGURE 19
BA
Set screw
B
6
7
FIGURE 18
Adjust power and aircraft cable length as needed to adjust the drop height and to level the fixture. Tighten the safety nut after completing adjustment.
5
Push wires inside the canopy and use set screws (removed in first instruction) to connect canopy to cover plate.
Use set screws (removed in first instruction) to connect canopy to top cap.
FLUTES LYDIAN ARRAY INSTALLATION GUIDE 7
WWW.JUNIPER-DESIGN.COM | [email protected] | +1 347 799-2915 | 157 WATER STREET SOUTHINGTON, CT 06489