Upload
doananh
View
213
Download
1
Embed Size (px)
Citation preview
John Deere | Water Delivery Products
Rotors | Internal Replacement Assemblies | Quantum Valves | Accessoires
John Deere rotors, valves and accessories.A consistent pattern of quality.
3
It started with a philosophy: to bring the finest
in design, manufacturing and support together
to produce the best in rotors, valves and acces-
sories for the golf course irrigation industry.
The result has been rotors that are stainless-steel tough,
housed in robust, industrial-grade plastic that can take the
brunt of man or nature. Valves that are ultra-reliable, fully
serviceable and a sensible cost alternative to expensive
pressure-regulated brass valves and accessories that
allow you to jet-clean equipment, syringe a thirsty green
or apply costly wetting agents evenly and efficiently.
At John Deere we pride ourselves on producing rotors,
valves and accessories that bring both innovation and
ease to your course at a reasonable price. These products
are the culmination of our commitment to be your full
service partner. Every model, feature and subsequent
combination of these products is designed with water
conservation in mind. For all of your water management
needs, contact your local John Deere dealer.
4
Even in blustery conditions, the 70 Series Rotors
offer an excellent blend of high performance and ease. The
Series has a built-in rear nozzle for improved coverage in
gusty conditions. Its unique design eliminates blow-by and
the part circle rotor features a field adjustable arc that
matches the spray pattern to the turf area.
A stainless-steel riser resists damage and pops up to a full
3 in (7.6 cm) to clear taller grasses. Dual-direction flushing
protects internals from debris. All internal components are
serviceable from the rotor’s top and the interchangeable
nozzles deliver superior precipitation rates in a variety of
radii and flows.
An efficient design,a rugged core.
70 Series Rotor
70-Series Golf Rotors
6
This full or part circle rotor is a John Deere Golf Irrigation, water-lubricated, gear-drive model capable of covering a radius of 20-23 metres at a base pressure of 4.1 bar and a discharge rate of 2.1-2.9 litres/sec as specified on the chart. The rotor is installed with a number 25 nozzle that is blue in colour for ease of identification.
A part circle 70 Series sprinkler has an adjustable arc with coverage of 35 to 360º. Arc adjustment can be performed without the need for any special tools and with the rotor in place. The part circle rotor will rotate through a 180º arc in two minutes or less. Rotation through 360º will take two and a half minutes or less for the full circle rotor.
All 70 Series rotors are serviceable from the top. Additionally, the riser is manu-factured of stainless steel and is self-flushing on both the up and the down action. The retract spring is made of stainless steel and of sufficient force for a positive retraction.
The rotor case is made of commercial-grade plastic and has a top diameter of 19 cm (7.50 in), a pop-up height of 7.6 cm (3.00 in) and an overall body height of 27.3 cm (10.75 in). The rotor has the option of 3.2 cm (1.25 in) female ACME, or 3.8 cm (1.5 in) female NPT or BSP threaded inlet. Rotors can be fitted with colour-coded, interchangeable nozzles.
Model Features
70 Series Golf Rotors
Optional Feature: Electric Valve-in-Head [70E or 75E]The electric valve in head rotor has a 24 VAC 50 or 60 cycle solenoid actuated control valve in the base of the case. The rotor has a top-serviceable manual selector that allows the rotor to be operated manually, shut off or in fully automatic control mode.
Optional Feature: Check Valve-in-Head [70C or 75C]This rotor has an optional spring-loaded Check-O-Matic holdback device in the base of the rotor body and is used with a pressure regulating, electrically actuated valve. The spring is capable of holding back a head of water of 4.6 m (15 ft).
Optional Feature: Hydraulic [70H or 75H]The rotor has a normally open (N.O.) hydraulic control valve in the base of the case and an on/off selector switch allowing it to be turned off in the field for service.
Models:Full Circle:70E: Electric Valve-in-Head70C: Check Valve-in-Head70H: Hydraulic (N.O.)Part Circle:75E: Electric Valve-in-Head75C: Check Valve-in-Head75H: Hydraulic (N.O.)
Arc:70 Series: Full Circle, 360º75 Series: Part Circle,35º to 360º
Maximum Inlet Pressure:70E and 75E: 150 psi (10.3 bar)70C and 75C: 150 psi (10.3 bar)70H and 75H: 150 psi (10.3 bar)
Pressure Regulation Range:60 to 90 psi (4.1 to 6.9 bar)
Factory Pressure Settings:70E and 75E available in60, 70, 80, 90 psi (4.1, 4.8, 5.5, 6.2 bar)
Standard Factory Setting:80 psi (5.5 bar)
Rotation Time:70 Series:360º in 150 seconds (nominally)75 Series:180º in 75 seconds (nominally)
Inlet Threads:3.2 cm (1.25 in) ACME female threaded3.2 cm (1.25 in) NPT female threaded3.2 cm (1.25 in) BSP female threaded**Standard Factory Threads
Check:70C and 75C Series:4.6 m (15 ft) elevation
Nozzle Trajectory:25º
Dimensions:Body Height: 27.3 cm (10.75 in)Top Diameter: 19.1 cm (7.50 in)Pop-Up Height: 7.6 cm (3.00 in)
Riser:Stainless Steel
Solenoid:24 VAC 50/60 HzInrush Amps: 0.30Holding Amps: 0.20
Specifications
7
70 Series70 Series Performance Data
Note all data is current at the time of printing and subject to change. Please check with the manufacturer for updated values before specifying. All nozzles were tested at a base pressure 10 psi (0.7 bar) above regulated pressure.
How to Specify/Order
Notes: (1) Base Pressure setting is ONLY used on E types [Electric Valve-in-Head]; it is omitted for C and H types. (2) Highlighted boxes indicate standard factory setting.
Examples: (a) 70 Series, Full Circle, Electric Valve-in-Head, #50-Black Nozzle, 80 psi (5.5 bar) pressure setting, BSP connection. Final Part No. would be: MC70E5080B (b) 70 Series, Part Circle, Check Valve-in-Head, #32-Yellow Nozzle, BSP connection. Final Part No. would be: MC75C32B
Full Circle Rotor Performance Data (UK)
#37Red
#40 Brown
#45Green
#50Black
#57Blue
Base Pressure
(psi)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
60 67 27.6 65 28.5 67 30.5 73 44.6 75 38.2
70 73 30.0 73 32.0 76 34.6 77 46.9 79 40.5
80 77 39.9 79 42.0 85 43.6 89 56.2 93 51.2
90 73 30.0 75 35.4 83 38.0 89 51.3 93 44.9
Full Circle Rotor Performance Data (Metric)
#37Red
#40Brown
#45Green
#50Black
#57Blue
Base Pressure
(bars)
Radius(m)
Flow(l/s)
Flow(m3/hr)
Radius(m)
Flow(l/s)
Flow(m3/hr))
Radius(m)
Flow(l/s)
Flow(m3/hr)
Radius(m)
Flow(l/s)
Flow(m3/hr))
Radius(m)
Flow(l/s)
Flow(m3/hr)
4.1 20.4 2.1 7.5 19.8 2.2 7.8 20.4 2.3 8.4 22.2 2.8 10.1 22.8 2.9 10.5
4.8 22.4 2.3 8.2 22.2 2.4 8.8 23.1 2.6 9.5 23.4 3.0 10.7 24.0 3.1 11.1
5.5 23.4 3.0 10.9 24.0 3.2 11.5 25.8 3.3 11.9 27.1 3.5 12.8 28.3 3.9 14.0
6.2 22.2 2.3 8.2 22.8 2.7 9.7 25.2 2.9 10.4 27.1 3.2 11.6 28.3 3.4 12.3
Part Circle Rotor Performance Data (UK)
#32Yellow
#36Gray
#41Orange
Base Pressure(psi)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
60 67 22.8 67 23.2 65 26.8
70 69 24.3 69 26.7 71 28.6
80 69 26.2 69 28.2 73 31.3
90 71 27.5 73 30.3 73 33.1
Part Circle Rotor Performance Data (Metric)
#32Yellow
#36Gray
#41Orange
Base Pressure(bars)
Radius(m)
Flow(l/s)
Flow(m3/hr)
Radius(m)
Flow(l/s)
Flow(m3/hr)
Radius(m)
Flow(l/s)
Flow(m3/hr)
4.1 20.4 1.7 6.2 20.4 1.8 6.4 19.8 2.0 7.3
4.8 21.0 1.8 6.6 21.0 2.0 7.3 21.6 2.2 7.8
5.5 21.0 2.0 7.2 21.0 2.1 7.7 22.2 2.4 8.6
6.2 21.6 2.1 7.5 22.2 2.3 8.3 22.2 2.5 9.1
70 Series Full Circle Golf Rotors
Model Valve Type Nozzle Base Pressure Thread Type
D70 = Full Circle Rotor E = Electric Valve-in-Head 37 = #37-Red 60 = 60 psi (4.1 bar) A = ACME (1¼)
C = Check Valve-in-Head 40 = #40-Brown 70 = 70 psi (4.8 bar) B = BSP (1½)
H = Hydraulic Valve-in-Head 45 = #45-Green 80 = 80 psi (5.5 bar) N = NPT (1½)
50 = #50-Black 90 = 90 psi (6.2 bar)
57 = #57-Blue
70 Series Part Circle Golf Rotors
Model Valve Type Nozzle Base Pressure Thread Type
D75 = Part Circle Rotor E = Electric Valve-in-Head 32 = #32-Yellow 60 = 60 psi (4.1 bar) A = ACME (1¼)
C = Check Valve-in-Head 36 = #36-Grey 70 = 70 psi (4.8 bar) B = BSP (1½)
H = Hydraulic Valve-in-Head 41 = #41-Orange 80 = 80 psi (5.5 bar) N = NPT (1½)
90 = 90 psi (6.2 bar)
8
Versatility. That describes the 50 Series, rotors that
work as well around greens and tees as they do in the
rough and fairways. They feature full circle and part circle
with adjustable patterns for maximum flexibility. Easy arc
adjustments can be made in the field without any special
tools. Three nozzle orifices provide the ultimate in uniform-
ity. The stainless-steel riser resists damage and pops up
to a full four inches to clear taller grasses. The compact
cartridge design enables quick and easy repair and the
Quicklock™ design allows internals to be serviced from
the rotor’s top.
Flexibility for whereyou need it most.
50 Series Rotor
50 Series Golf Rotors
9
10
This full or part circle rotor is a John Deere Golf Irrigation, water-lubricated, gear-drive model capable of covering an 11-19 metre radius at a base pressure of 4.1 bar and a discharge rate of 0.5-1.8 litre/sec as specified on the chart. The rotor is installed with a number 25 nozzle that is blue in colour for ease of identification.
The part circle 50 Series sprinkler has an adjustable arc coverage of 35 to 360º. Arc adjustment can be performed without the need for any special tools and with the rotor in place. The part circle will rotate through a 180º arc in two minutes or less. Rotation through 360º will take two and a half minutes or less for the full circle rotor.
All 50 Series rotors are serviceable from the top with a Quicklock™ design. The riser is of stainless steel and is self-flushing on both up and down action. The retract spring is stainless steel and has sufficient force for positive retraction.
The rotor case is made of commercial-grade plastic and has a top diameter of 16.5 cm (6.50 in), a pop-up height of 10.2 cm (4.00 in) and an overall body height of 24.7 cm (9.75 in). The rotor is 25.4 mm (1 in) female ACME, NPT or BSP threaded inlet.
Model Features
50 Series Golf Rotors
The rotor is colour-coded with interchangeable nozzles.
Optional Feature: Electric Valve-in-Head [50E or 55E]The rotor has a 24 VAC 50 or 60 cycle solenoid actuated normally closed control valve in the base of the case. For manual shut off or in fully automatic control mode operation, the rotor has a top-serviceable manual selector.
Optional Feature: Check Valve-in-Head [50C or 55C]Optionally, the rotor has a spring-loaded Check-O-Matic holdback device in the base of its body and is used with a pressure-regulating, in-line electrically actuated valve; the spring is capable of holding back a head of water of 4.6 m (15 ft).
Optional Feature: Hydraulic [50H or 55H]The rotor has a normally open (N.O.) hydraulic control valve in the base of the rotor body and is capable of holding back a head of water of 4.6 m (15 ft). This rotor also features an on/off selector switch allowing it to be turned off in the field for service.
Models:Full Circle:50E: Electric Valve-in-Head50C: Check Valve-in-Head50H: Hydraulic (N.O.)Part Circle:55E: Electric Valve-in-Head55C: Check Valve-in-Head55H: Hydraulic (N.O.)
Arc:50 Series: Full Circle, 360º55 Series: Part Circle,35º to 360º
Maximum Inlet Pressure:50E and 55E: 150 psi (10.3 bar)50C and 55C: 150 psi (10.3 bar)50H and 55H: 150 psi (10.3 bar)
Pressure Regulation Range:60 to 80 psi (4.1 to 5.5 bar)
Factory Pressure Settings:50E and 55E available in 60, 70, 80 psi (4.1, 4.8, 5.5 bar)
Standard Factory Setting:70 psi (4.8 bar)
Rotation Time:50 Series:360º in 150 seconds (nominally)55 Series:180º in 75 seconds (nominally)
Inlet Threads:2.5 cm (1 in) ACME female threaded2.5 cm (1 in) NPT female threaded2.5 cm (1 in) BSP female threaded** Standard Factory Threads
Check:50C and 55C Series:4.6 m (15 ft) elevation
Nozzle Trajectory:25º
Dimensions:Body Height: 24.7 cm (9.75 in)Top Diameter: 16.5 cm (6.50 in)Pop-Up Height: 10.2 cm (4.00 in)
Riser:Stainless Steel
Solenoid:24 VAC 50/60 HzInrush Amps: 0.30Holding Amps: 0.20
Specifications
11
50 Series50 Series Performance Data
Notes: (1) Base Pressure setting is ONLY used on E types [Electric Valve-in-Head]; it is omitted for C and H types. (2) Highlighted boxes indicate standard factory setting. (3) Light green boxes indicate nozzle performance is not optimum at designated pressure.
Example: 50 Series, Full Circle, Electric Valve-in-Head, #25-Blue Nozzle, 70 psi (4.8 bar) pressure setting, BSP thread type. Final Part No. would be: MC50E2570B
Note all data is current at the time of printing and subject to change. Please check with the manufacturer for updated values before specifying. All nozzles were tested at a Base Pressure 10 psi (0.7 bar) above Regulated Pressure.
How to Specify/Order
50 Series Golf Rotors Medium Range
Model Type Nozzle Base Pressure Thread Type
D50 = 1″ Full Circle Rotor E = Electric Valve-in-Head 08 = #08-Black 60 = 60 psi (4.1 bar) A = ACME
D55 = 1″ Part Circle Rotor C = Check Valve-in-Head 12 = #12-Grey 70 = 70 psi (4.8 bar) B = BSP
H = Hydraulic Valve-in-Head 14 = #14-Yellow 80 = 80 psi (5.5 bar) N = NPT
16 = #16-Orange 90 = 90 psi (6.2 bar)
18 = #18-Brown
19 = #19-Red
25 = #25-Blue
28 = #28-Green
Full Circle Rotor Performance Data (UK)
#08Black
#12 Grey
#14Yellow
#16Orange
#18Brown
#19Red
#25Blue
#28Green
Base Pressure(psi)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
60 37 6.6 39 8.2 47 11.5 51 14.0 53 16.4 55 16.4 59 18.8 62 23.2
70 37 8.4 39 9.5 47 12.8 55 15.2 57 16.8 55 17.5 67 22.1 71 25.6
80 59 18.4 69 23.7 72 26.9
Full Circle Rotor Performance Data (Metric)
Base Pressure(bars)
Radius(m)
Flow(l/s)
Flow(m3/hr)
Radius(m)
Flow(l/s)
Flow(m3/hr)
Radius(m)
Flow(l/s)
Flow(m3/hr)
Radius(m)
Flow(l/s)
Flow(m3/hr)
Radius(m)
Flow(l/s)
Flow(m3/hr)
Radius(m)
Flow(l/s)
Flow(m3/hr)
Radius(m)
Flow(l/s)
Flow(m3/hr)
Radius(m)
Flow(l/s)
Flow(m3/hr)
4.1 11.2 0.5 1.8 11.9 0.6 2.2 14.3 0.9 3.1 15.5 1.1 3.8 16.1 1.2 4.5 16.7 1.2 4.5 17.9 1.4 5.1 18.8 1.8 6.4
4.8 11.2 0.6 2.3 11.9 0.7 2.6 1.3 1.0 3.5 16.7 1.2 4.2 17.3 1.3 4.6 16.7 1.3 4.8 20.4 1.7 6.0 21.6 1.9 7.0
5.5 18.0 1.4 5.0 21.0 1.8 6.5 21.9 2.0 7.4
Part Circle Rotor Performance Data (UK)
#08Black
#12 Grey
#14Yellow
#16Orange
#18Brown
#19Red
#25Blue
#28Green
Base Pressure(psi)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
60 37 6.6 40 7.5 49 9.9 53 12.5 57 13.9 55 16.4 61 17.6 63 21.9
70 37 8.4 40 10.0 47 12.0 51 13.5 55 15.2 55 17.5 59 20.3 65 21.7
80 59 18.4 65 21.9 67 25.4
Part Circle Rotor Performance Data (Metric)
Base Pressure(bars)
Radius(m)
Flow(l/s)
Flow(m3/hr)
Radius(m)
Flow(l/s)
Flow(m3/hr)
Radius(m)
Flow(l/s)
Flow(m3/hr)
Radius(m)
Flow(l/s)
Flow(m3/hr)
Radius(m)
Flow(l/s)
Flow(m3/hr)
Radius(m)
Flow(l/s)
Flow(m3/hr)
Radius(m)
Flow(l/s)
Flow(m3/hr)
Radius(m)
Flow(l/s)
Flow(m3/hr)
4.1 11.2 0.5 1.8 12.2 0.6 2.0 14.9 0.8 2.7 16.1 0.9 3.4 17.3 1.1 3.8 16.7 1.2 4.5 18.5 1.3 4.8 19.2 1.7 6.0
4.8 11.2 0.6 2.3 12.2 0.8 2.7 14.3 0.9 3.3 15.5 1.0 3.7 16.7 1.2 4.2 16.7 1.3 4.8 17.9 1.5 5.5 19.8 1.7 6.0
5.5 18.0 1.4 5.0 19.8 1.7 6.0 20.4 1.9 6.9
12
Wherever you need uniformity, the 50 Series
Block Rotors can rise to the occasion. A stainless-steel
riser resists damage and pops up to a full four inches to
clear taller grasses. Dual-direction flushing protects
internals from debris and all internal components are
serviceable from the rotor’s top. Choose from multiple
interchangeable nozzles that deliver superior precipitation
rates in a variety of radii from 6.4 m to 22.5 m (21 ft to 74 ft)
and flows from 0.4 to 2.3 l/s (4.1 to 25.3 gpm).
A spray pattern to match any turf, anywhere on the course.
50 Series Block Rotors
This full or part circle rotor is a John Deere Golf Irrigation, water-lubricated, gear-drive model capable of covering a 6.4-19.7 metre radius at a base pressure of 3.5 bar and a discharge rate of 0.4-1.86 litre/sec as specified on the chart. The rotor is installed with a number 25 nozzle that is blue in colour for ease of identification.
A part circle 50B sprinkler has an adjustable arc coverage of 35º to 360º. Arc adjustment can be performed without the need for any special tools with the rotor in place. The part circle rotor rotates through a 180º arc in two minutes or less. Rotation through 360º is two and a half minutes or less for the full circle rotor.
All 50B rotors are serviceable from the top with a Quicklock™ design. The riser is manufactured of stainless steel and is self flushing on both up and down action. The retract spring is also made of stainless steel and of sufficient force for a positive retraction.
Model Features
The rotor case is made of commercial-grade plastic and has a top diameter of 14.6 cm (5.75 in), a pop-up height of 10.2 cm (4.00 in) and an overall body height of 22.2 cm (8.75 in). The rotor has 2.5 cm (1 in) female ACME, NPT or BSP threaded inlet.
The rotor can be fitted with colour-coded, interchangeable nozzles.
The rotor also has a check holdback feature and is used with an in-line electri-cally actuated valve or integrated electrically actuated valve with the capability of holding back a head of water of 4.6 m (15 ft).
Models:Full Circle:50B: Block RotorPart Circle:55B: Block Rotor
Arc:50B Series: Full Circle, 360º55B Series: Part Circle, 35º to 360º
Maximum Inlet Pressure:50B and 55B: 150 psi (10.3 bar)
Rotation Time:50B Series:360º in 150 seconds (nominally)55B Series:180º in 75 seconds (nominally)
Inlet Threads:2.5 cm (1 in) BSP female threaded2.5 cm (1 in) NPT female threaded2.5 cm (1 in) BSP female threaded
Standard Factory Threads:2.5 cm (1 in) BSP female threaded
Check:Checks and holds back a head of water up to 4.6 m (15 ft)
Nozzle Trajectory:25º
Riser:Stainless Steel
Specifications
13
50 Series Block Rotors
Notes: Highlighted boxes indicate standard factory setting.Example: 50 Series Full Circle Block Rotor, #25-Blue Nozzle, BSP thread type. Final Part No. would be: MC50B25B
How to Specify/Order
50 Series Block Rotor
50 Series Block Rotors
Model Nozzle Thread Type
D50B = 1″ Full Circle Block Rotor 08 = #08-Black A = ACME
D55B = 1″ Part Circle Block Rotor 12 = #12-Grey B = BSP
14 = #14-Yellow N = NPT
16 = #16-Orange
18 = #18-Brown
19 = #19-Red
25 = #25-Blue
28 = #28-Green
14
• Electric Valve-In-Head, Hydraulic Valve-In-Head, Check Valve-in-Head.• 2.54 cm (1 in) X Series rotor features a full four inch pop-up clearing tall turf
grass for even coverage. 3.8 cm (1.5 in) X Series rotor features a full three inch pop-up.
• Rolled-over flange head keeps turf grass clear of riser and nozzle. • Stainless-steel riser resists damage. • Special design eliminates blow-by and reduces pressure loss to improve sys-
tem performance.• Dual-direction flushing protects internals from debris and ensures positive pop-
up/down.• Full circle and adjustable patterns for maximum flexibility (two back-to-back
part circle rotors in one case).• Easy arc adjustment in the field without any tools.
X Series Golf Rotors
• Unique manual On/Off control for hydraulic rotors.• Heavy duty spring assures positive retraction.• Radius can be adjusted up to 25% for best coverage.• Comprehensive 3-year warranty.• Dual-radius part circle operation.• AUTO/OFF/ON selector on the electric VIH models.• D75X uses the same case as the 70 Series but with a different internal drive.
The drives are available separately and are retrofitable to all existing 70 Series.
• D55X uses the same case as the 50 Series but with a different internal drive. The drives are available separately and are retrofitable to all existing 50 Series.
Sometimes, what’s in front of you is not the same as what’s behind you.
Say for instance, the green is in front and a bunker is in back. It’s the perfect
situation for our X Series Golf Rotors. The revolutionary X™ Technology offers
dual adjustable patterns from front and back nozzles of the same sprinkler head.
It’s like getting two rotors in one body.
Each nozzle achieves a similar radius at different flow rates, giving you precise
irrigation at the transitional areas of your golf course. No other rotor can match
the X Series in irrigation of greens and aprons and at fairway edges for supple-
mental watering of roughs.
Water where you need it, less where you don’t. It’s truly water conservation at
its finest.
Unique situations call for a unique rotor.
1 Head – 2 Flow Rates
Model Features
70 Series Rotor
Off Green: 21.34 m (70 ft) radius, 2.21 l/s (29.1 gpm)
On Green: 18.29 m (60 ft) radius, 1.14 l/s (14.9 gpm)
Fairway — Rough Green — Mounds Bunker
On Fairway On Rough On Green On Mounds On Green On Bunker
2.21 l/s 29.1 gpm
21.34 m (70 ft) radius
1.01 l/s13.3 gpm
16.8 m (55 ft) radius
0.88 l/s 11.6 gpm
16.8 m (55 ft) radius
1.51 l/s19.9 gpm
19.8 m (65 ft) radius
1.51 l/s19.9 gpm
19.8 m (65 ft) radius
0.51 l/s6.6 gpm
10.67 m (35 ft) radius
15
X SeriesPop-up Height:55X: 10.2 cm (4 in); 75X: 7.4 cm (3 in)
Radius:4.57-21.34 m (15-70 ft)
Flow Rate:1.89-3.34 l/s (25.3-44 gpm)
Inlet (bottom):Standard 3.2 cm (1.25 in) BSP on 75Xand 2.5 cm (1 in) BSP on 55X
Check:Checks and holds back, a head of water up to 4.6 m (15 ft)
Pressure Regulation & Range:Standard at 80 psi (5.5 bar) 75X and70 psi (4.8 bar) 55X
Operating Pressure Range:60-90 psi (4.1-6.2 bar)
Maximum Pressure:150 psi (10.3 bar)
Body Height:27.3 cm (10.75 in) 75X and 24.8 cm (9.75 in) 55X
Top Diameter:19 cm (7.5 in) 75X and 16.5 cm (6.5 in) 55X
Adjustable Arc:35-360 degrees(Part Circle models)
Specifications
X Series Performance Data
How to Specify/Order
Note all data is current at the time of printing & subject to change. Please check with the manufacturer for updated values before specifying. All nozzles were tested at a Base Pressure 10 psi (0.69 bar) above regulated pressure.
Notes: (1) Base Pressure setting is ONLY used on E types [Electric Valve-in-Head]; it is omitted for C and H types. (2) Highlighted boxes indicate standard factory setting.Example: X Series Rotor, Check Valve-in-Head, #25-Blue Nozzle (Front), #12-Grey Nozzle (Rear), BSP thread type. Final Part No. would be: MC55XC2512B.
1½″ Rotor Performance Data
Front Nozzle (180˚) Rear Nozzle (180˚) Totall/s /gpmNozzle Radius m / ft l/s / gpm Nozzle Radius m / ft l/s / gpm
#35Yellow
21.34 / 70 2.21 / 29.1 #14
Yellow15.54 / 50 0.89 / 11.6 3.10 / 40.7
21.34 / 70 2.21 / 29.1#16
Orange16.76 / 55 1.01 / 13.3 3.23 / 42.3
21.34 / 70 2.21 / 29.1#18
Brown18.29 / 60 1.14 / 14.9 3.35 / 44.0
1″ Rotor Performance Data
Front Nozzle (180˚) Rear Nozzle (180˚) Totall/s /gpmNozzle Radius m / ft l/s / gpm Nozzle Radius m / ft l/s / gpm
#25Blue
18.29 / 60 1.52 / 19.9#08
Black10.66 / 35 0.51 / 6.6 2.02 / 26.6
18.29 / 60 1.52 / 19.9#12 Red
13.72 / 45 0.76 / 10 2.28 / 29.9
18.29 / 60 1.52 / 19.9#14
Yellow16.76 / 55 0.89 / 11.6 2.40 / 31.5
1″ Golf Rotors Dual-Nozzle, Dual Part Circle
Model TypeNozzle Configuration Base Pressure
[E-Models Only]Thread Type
Front Rear
D55X = 1″ X Series Rotor E = Electric Valve-in-Head 25 = #25-Blue 08 = #08-Black 60 = 60 psi (4.1 bar) A = ACME
C = Check Valve-in-Head 12 = #12-Grey 70 = 70 psi (4.8 bar) B = BSP
H = Hydraulic Valve-in-Head 14 = #14-Yellow 80 = 80 psi (5.5 bar) N = NPT
90 = 90 psi (6.2 bar)
1½″ Golf Rotors Dual-Nozzle, Dual Part Circle
Model TypeNozzle Configuration Base Pressure
[E-Models Only]Thread Type
Front Rear
D75X = 1½″ X-Series Rotor E = Electric Valve-in-Head 35 = #35-Yellow 14 = #14-Yellow 60 = 60 psi (4.1 bar) A = ACME
C = Check Valve-in-Head 16 = #16-Orange 70 = 70 psi (4.8 bar) B = BSP
H = Hydraulic Valve-in-Head 18 = #18-Brown 80 = 80 psi (5.5 bar) N = NPT
90 = 90 psi (6.2 bar)
16
High Performance• Low pressure loss• Unique snap ring serviceability• 200 psi (13.8 bar) pressure rating• Common solenoid with valve-in-head (E-models)• Male pipe threads for strength and high pressure rating
Quantum Valves
Quantum Valves
Hydraulic Pressure Regulated ValvesMC150H 3.8 cm (11/2 in) NPTMC200H 5 cm (2 in) NPT
Electric Pressure Regulated ValvesMC100E 2.5 cm (1 in) NPTMC150E 3.8 cm (11/2 in) NPTMC200E 5 cm (2 in) NPT
Factory Pressure Settings:Available in 35, 50, 65 and 80 psi (2.4, 3.4, 4.5, 5.5 bar)
Standard Factory Settings:80 psi (5.5 bar)
Solenoid24 VAC 50/60 HzInrush Amps: 0.30Holding Amps: 0.20
Electric Dirty Water ValvesMC150E3 3.8 cm (11/2 in) NPTMC200E3 5 cm (2 in) NPT
Solenoid24 VAC 50/60 HzInrush Amps: 0.30Holding Amps: 0.20
How to Specify/Order
Performance Data
Example: To order 11/2″ (38.1 mm) Electric Pressure Regulated valve set at 60 psi, (4.1 bar) you would specify MC150E60.
Model Features
MC100, MC150 and MC200 Quantum Valves
Style/Size TypePressure Regulation[Electric Models Only]
MC100E = 1″ E = Pressure Regulated Electric 35 = 35 psi (2.4 bar)
MC150E = 11/2″ E3 = Electric Dirty Water 50 = 50 psi (3.4 bar)
MC200E = 2″ H = Hydraulic 65 = 65 psi (4.5 bar)
Quantum Series Valve Pressure Loss (UK)
psi Loss
Flow Rate (gpm)
30 40 50 70 90 100 120 150 180
11/2″ 1.2 1.2 1.2 1.2 2.9 3.3 4.2 4.6 6.6
2″ 1.2 1.2 1.2 2.9 3.7 4.6 5.0 7.5 —
psi Loss
Flow Rate (gpm)
5 10 20 30 40
1″ 1.7 2.1 2.9 4.2 7.1
Quantum Series Valve Pressure Loss (Metric)
Bar Loss
Flow Rate (l/s)
1.90 2.53 3.16 4.43 5.69 6.33 7.79 9.49 11.39
38.1 mm 0.10 0.10 0.10 0.10 0.24 0.28 0.34 0.38 0.55
50.8 mm 0.10 0.10 0.10 0.24 0.31 0.38 0.41 0.62 –
Bar Loss
Flow Rate (l/s)
0.32 0.69 1.38 1.90 2.53
25.4 mm 0.14 0.17 0.24 0.34 0.59
17
Internal Replacement
Assemblies
Internal Replacement Assemblies
Performance Data
Note all data is current at the time of printing & subject to change. Please check with the manufacturer for updated values before specifying. All nozzles were tested at a Base Pressure 10 psi (0.7 bar) above Regulated Pressure.Notes: (1) Highlighted boxes indicate standard factory setting. (2) Light green boxes indicate nozzle performance is not optimum at designated pressure.
MCI6785T Performance Data
#16 Orange
#21Brown
#26Blue
#29Red
#32Grey
Base Pressure
(psi)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
50 56 10.8 61 13.6 62 18.1 65 18.6 66 21.4
60 57 11.8 62 14.9 64 19.4 70 20.8 71 22.3
70 58 12.8 64 16.1 66 20.6 72 22.4 75 24.7
80 59 13.6 65 17.2 67 21.6 75 23.9 78 26.3
90 60 14.5 68 18.2 70 23.3 77 25.4 80 27.8
100 61 15.4 70 19.2 70 23.3 79 26.6 82 29.3
TORO® Nozzle Reference
650 54 55 56 57 58
780 83 84 85 – 86
MCI6734T, MCI6735T & MCI865T Performance Data
#14Yellow
#16 Orange
#18Brown
#25Blue
#28Green
Base Pressure
(psi)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
50 52 9.1 55 11.0 60 13.9 62 18.1 66 20.7
60 54 10.8 57 12.4 62 14.5 64 19.4 68 22.1
70 56 12.0 59 13.5 63 15.4 66 20.6 70 23.3
80 58 12.9 60 14.5 65 16.6 67 21.6 71 24.5
90 59 13.5 61 15.0 67 18.2 70 23.3 73 27.0
100 59 13.5 61 15.0 67 18.2 70 23.3 73 27.0
TORO® Nozzle Reference
630 31 32 33 34 –
660 – 62 63 – 64
730 31 32 33 34 35
760 62 63 64 65 66
MCI700R/MCI750R & MCI51R/MCI47R Performance Data
#14 Orange
#16Brown
#18Blue
#20Red
Base Pressure
(psi)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
50 52 10.4 55 14.1 60 18.3 64 20.3
60 55 11.2 58 15.4 62 19.5 66 21.6
70 157 12.5 60 16.5 65 20.7 67 22.8
80 61 14.0 62 18.3 66 21.6 68 24.1
90 61 14.9 62 19.5 67 22.4 70 26.1
100 61 15.8 62 19.9 67 23.7 70 27.4
Rain Bird® Nozzle Reference
47D 18 16 18 20
51D – 16 18 20
MCI674754T & MCI694T Performance Data
#29Yellow
#32 Grey
#37Red
#40Brown
#45Green
#50Black
#57Blue
Base Pressure
(psi)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
50 – – – – – – – – – – – – – –
60 66 20.8 68 22.3 74 28.2 78 31.5 80 34.5 – – – –
70 69 22.4 71 24.7 75 29.5 79 32.4 82 35.7 85 39.4 85 45.7
80 72 23.9 74 26.3 76 30.7 80 33.2 84 37.4 87 41.5 87 47.3
90 74 25.4 76 27.8 78 32.0 82 34.5 86 39.0 89 46.5 90 48.6
100 76 26.6 78 29.3 78 33.7 84 35.7 87 40.7 91 47.3 100 54.8
TORO® Nozzle Reference
650 56 57 58 59 – – –
670 – – – 70 71 72 73, 74
680 – 84 85 86 87 88 –
750 54 55 56 – 57 58 –
780 84 85 86 87 88 89 –
MCI5025 & MCI5525 Performance Data
#06Blank
#08 Black
#14Yellow
#16Orange
#16Brown
#25Blue
#28Green
Base Pressure
(psi)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
Radius(ft)
Flow(gpm)
50 21 4.1 30 5.6 53 9.1 56 10.9 61 13.7 63 18.1 65 20.3
60 34 4.5 32 6.3 55 10.7 58 12.3 62 14.6 64 19.4 67 22.0
70 39 5.2 34 7.0 57 12.0 60 13.4 62 15.5 65 20.6 69 23.3
80 – – – – – 12.0 – 13.4 – 15.5 66 21.6 74 25.3
90 _ _ – – – – – – – – – – – –
100 _ _ – – – – – – – – – – – –
Rain Bird® Nozzle Reference
700 – – 14 16 18 20 –
750 – – 14 16 18 20 –
Replacements for Toro®:
2.5 cm (1 in) Inlet Bodies MCI6734T Full circle, Toro 634 & 734 MCI6735T Part circle, Toro 635 & 735 MCI834T Full circle, Toro 834 MCI865T Part circle, Toro 865 Radius: 15.85-22.86 m (52-75 ft) Flow rate: 0.70-2.23 l/s (9.1-29.5 gpm) MCI6735TX Conversion for X2 Upgrades for Toro 630, 660, 730 & 760
3.8 cm (11/2 in) Inlet Bodies Replacement Upgrade MCI674754T Full circle, Toro® 654, 674, 754 Radius: 20.12-30.48 m (66-100 ft) Flow rate: 1.58-4.16 l/s (20.8-54.8 gpm)
Replacement Upgrade MCI6785T Part circle, Toro® 765, 785 Radius: 17.07-24.99 m (56-82 ft) Flow rate: 0.82-2.23 l/s (10.8-29.3 gpm) MCI6785TX Conversion for X2 Upgrades for Toro® 765 & 785
Replacement Upgrade for: MCI694T Full circle, Toro® 694 Radius: 27.74-30.48 m (91-100 ft) Flow rate: 3.6-4.16 l/s (47.3-54.8 gpm)
Replacements for Rain Bird®:
3.1 cm (11/4 in) Inlet Bodies MCI700R Full circle, Rain Bird® Eagle 700 MCI750R Part circle, Rain Bird® Eagle 750 Radius: 16.15-21.95 m (53-72 ft) Flow rate: 0.79-2.08 l/s (10.4-27.4 gpm) MCI750RX Conversion for X2 Upgrades for Rain Bird® Eagle 750
3.8 cm (11/2 in) Inlet Bodies MCI51R Full circle, Rain Bird® 51D MCI47R Part circle, Rain Bird® 51D Radius: 16.15-21.95 m (53-72 ft) Flow rate: 0.79-2.09 l/s (10.4-27.4 gpm) MCI47RX Conversion for X2 Upgrades for Rain Bird® 47DR
18
Hose end Accessories
Valve-In-Head Adapters & Hose Economical 360° swivel action hose adapter for John Deere, TORO, Rain Bird and Hunter sprinklers. 1.9 cm (0.75 in) and 2.5 cm (1 in) hose outlet. Includes brass 1.9 cm (0.75 in) x 2.5 cm (1 in) adapter (Part # MC1158).
CoolShot™ & CoolShot™ Plus withRegulator Shower Nozzles The new CoolShot’s improved shower pattern is now unbeatable for cooling and soaking your greens. CoolShot Plus with regulator includes ON/OFF and fl ow control.
CoolShot™ Plus withRegulator Economy Shower Nozzle Not as sleek as its aircraft aluminium brother but this economy version of the CoolShot Plus with regulator offers the same great shower pattern and features high strength composite construction and a nice low price.
HotShot™ withRegulator Multi-Pattern Nozzle If you could only have one nozzle, this would be it. This heavy duty HotShot sprays hot spots, jet cleans equipment and soaks greens.
Wetting Agent ApplicatorApply your costly wetting agents evenly and effi ciently. On/off, variable fl ow control unit connects easily to the beginning or end of your hose. Two-tablet (6.3 cm (2.5 in) dia. x 7.6 (3 in) length max) capacity yields 0.81 Hectares (2 acre) coverage.
FanShot™ Spray NozzlesSlotted fan spray nozzles designed for various fl ows both with and without regulators.
Hose End
Accessories
CoolShotMCN100CS CoolShot 2.5 cm (1 in) hose threadCoolShot PlusMCN100CSP CoolShot Plus 2.5 cm (1 in) hose thread
HotShotMCN100HSM HotShot 2.5 cm (1 in) hose thread
CoolShot Plus EconomyMCN075CSPE CoolShot Plus Economy 1.9 cm (0.75 in) hose threadMCN100CSPE CoolShot Plus Economy 2.5 cm (1 in) hose thread
Hose AdaptersMC1125 Hose adapter, 2.5 cm (1 in)MC1126 adapter, 3.8 cm (1.5 in)Hose SwivelsMC100HS Hose swivel 2.5 cm (1 in)HoseHead™ All-In-One Hose Adapters & SwivelsValve-In-Head Hose Adapter & Swivel – John DeereMC50HA Hose adapter and swivel for 50 SeriesMC70HA Hose adapter and swivel for 70 SeriesValve-In-Head Hose Adapter & Swivel – Competitve ReplacementMC100HA Hose adapter, 2.5 x 2.5 cm (1 x 1 in) inlet, Deere and ToroMC150HA Hose adapter, 2.5 x 3.8 cm (1 x 1.5 in) inlet, Deere and ToroMC700RHA Hose adapter, 2.5 cm (1 in) Eagle 700
FanShot NozzlesMCN100FS20 FanShot 20 gpm, 1.26 l/s (20 gpm), 2.5 cm (1 in) hose thread
FanShot Plus with NozzlesMCN100FSP20 FanShot Plus 20 gpm, 1.26 l/s (20 gpm), 2.5 cm (1 in) hose thread
FanShot Plus with 3 Nozzle CombosMCN100FSP FanShot Plus w/ 3 nozzle combos, 2.5 cm (1 in) hose thread
Wetting Agent ApplicatorsMC100APL Wetting agent applicator, 2.5 cm (1 in) hose inlet – 1.9 cm (0.75 in) outlet
Wetting Agent Applicators with CoolShot NozzlesMCN100APLCS Wetting agent applicator, 2.5 cm (1 in) hose inlet – 1.9 cm (0.75 in) outlet w/ CoolShot
GuzzlerMCN100G Ground water extraction device
19
Rotor
Installation
Rotor Installation
Hydraulic Check-O-Matic
Block Electric
Unitised Swing JointNote: Adjust angle of swing joint; lay arm
between 30 to 45° to allow adequate impact absorption.
Rotor
BSPThreaded inlet size: 2.5 cm (1 in) Hand tighten until snug and back off 1/4 turn.
Lateral Line FittingLateral Line
Unitised Swing JointNote: Adjust angle of swing joint; lay arm
between 30 to 45° to allow adequate impact absorption.
Rotor
BSPThreaded inlet size: 3.1 cm (1.25 in) Hand tighten until snug and back off 1/4 turn.
Lateral Line Fitting
Lateral Line
Unitised Swing JointNote: Adjust angle of swing joint; lay arm
between 30 to 45° to allow adequate impact absorption.
Rotor
BSPThreaded inlet size: 3.1 cm (1.25 in) Hand tighten until snug and back off 1/4 turn.
Lateral Line FittingLateral Line
Waterproof Wire Connectors
Controller Wire Expansion Coil
Unitised Swing JointNote: Adjust angle of swing joint; lay arm
between 30 to 45° to allow adequate impact absorption.
Rotor
BSPThreaded inlet size: 3.1 cm (1.25 in) Hand tighten until snug and back off 1/4 turn.
Lateral Line Fitting
Lateral Line
Hydraulic Controller Tubing
This literature has been compiled for worldwide circulation. While general information, pictures and descriptions are provided, some illustrations and text may include finance, product options and accessories NOT AVAILABLE in all regions. PLEASE CONTACT YOUR LOCAL DEALER FOR DETAILS. John Deere reserves the right to change specification and design of products described in this literature without notice.
YY
0834
602E
3
/08 1/1
//2
www.JohnDeere.co.uk
OfficialGolf CourseEquipmentSupplier