Carter Process Control GmbH

CPC NEWS Issue 9 2015

JANUARY2015

Continually expanding and growing CPC is now delighted to announce strategic partners

are in place globally to support service and commissioning of its products.

After increased demand from our customers and the end users continual requests to help

with installation and commissioning we have taken these requests on board to be able to

provide manpower to support this.

Our products often call for highly skilled installation and as such our customers rely on the

technical expertise of CPC to provide them with the help needed.

CPC has identified and verified a number of highly competent service companies that can

act as our partner in providing this manpower along with Site Supervision of CPC technical

experts.

All direct quoting and specification will be handled by the sales team in Vienna who will

coordinate the despatch of the sub contracted workforce appropriate for the work required.

This enables one contact for the customer and a seemless transaction managed directly by

CPC from its headquarters.

For more information please contact the sales office in Austria sales@carterprocess.com

SERVICE & SUPPORT

Do We Refurbish!! The answer is very simple—”Of Course We Do”

Today’s financial restrictions often make it impossible for plants to just replace parts when

they feel like it and often have to make do with what they have got or repair the parts that

are damaged. Quite often we are sent parts to evaluate if they can be repaired and brought

back to specification. Not only that we can often make recommendations for improvement

to help increase the life of the parts and cut back on maintenance spend. But of course the

other advantage of using CPC is you know that if it cannot be repaired we can manufacture

a new part quickly and economically.

Plug Assembly seat skimmed and stem polished ready for return to site.

Major Deliveries

Page 2 CPC NEWS ISSUE 9 2015

CPC delivers 16 identical trim sets to 3 Power Stations in Asia for their HPLP OTC Valves.

Improvements to the design were also implemented to reduce erosion and improve life

expectancy of the trims. The main improvements were:

1. increasing the number of pressure reduction stages in the Disk Stack along with

increased Labyrinths for the low flow condition.

2. Disk stack inlet path increased to help the blocking problems experienced with the

OEM trim.

3. The Plug guiding surface was increased preventing too much medium at high

velocity entering the seat area.

4. The plug had a CrCN (Chromium Carbonitride) coating applied increasing the

surface hardness to more than 2000HV to protect against the erosion seen on the

OEM parts.

5. The seat ring material was upgraded from 410SST to Inconel.

All of the above was presented to the Alstom Technical team who took the decision that

CPC was the right choice to give them the best solution and economical return.

Our Representative CVI Services and Supply PTY Ltd managed the project locally with the

Power Stations and are also contracted to make the installations of the trims during the

upcoming outages,

Spray Nozzles—Leaving Fast

CPC NEWS ISSUE 9 2015 Page 3

The demand for the CPC replacement Spray

Water Nozzles has exceeded our wildest

expectations. We originally manufactured

and stocked 20 pieces of each Nozzle size i.e

OP2025, OP2060, OP2815, OP2830,

OP4010, OP4010H, OP4030, OP4030H

OP5610 & OP5630 but current demand has

suggested we have vastly under estimated

our stocking requirements so we are in the

process of increasing this quantity by up to 5

times (depending on size)

In addition soft goods kits for all sizes of

nozzles are in stock and ready for immediate

despatch.

CV 0.74—No problem for CPC

CPC can engineer any severe service trim to meet the customers needs. Here we were

asked to produce 2 Disk Stacks with 10 stages of pressure reduction but only pass 0.74

CV maximum for a spraywater valve. If it is physically possible then CPC can design and

manufacture it. Below is the stack supplied and although it looks like a solid block there

is a single line of inlets that enter the stack passing through the 10 stages required and

giving the required CV.

At CPC we endeavour to provide our customers with the best possible service

and local contact which is why it is vital for us to ensure we have the right

Representative partner in a Country to adopt the same philosophies as us in

giving the best service.

We are delighted to inform you of the following addition to the CPC family with

the below new representative:

Flenkorus UAB is now our official and exclusive representative in Azerbijan,

Kazakhstan, Turkmenistan, & Sakhalin Island (Russia).

Please visit the contacts page on our website to get their full contact details.

CPC has a huge amount of soft goods in stock for all CCI & BTG Valves that can

be shipped the same day. We have taken this away from the factory and

installed a warehouse directly in the offices enabling us to process these much

faster.

Don’t Forget Your Soft Goods

Europaring F15

Brunn am Gebirge

A-2345

Austria

tel: +43 123 60040

Fax: +43 123 600401

Email: sales@carterprocess.com

Web: www.carterprocess.com

CPC NEWS ISSUE 9 2015 Page 4

New Representative