ISA-TR20.00.01-2007 Measurement and Control Instruments

TECHNICAL REPORT

ISA-TR20.00.01-2007Updated with 27 new specification forms in 2004-2006

Updated with 11 new specification forms in 2007

Specification Forms for Process Measurement and Control Instruments

Part 1: General Considerations

Copyright International Society of Automation Provided by IHS under license with ISA

Not for ResaleNo reproduction or networking permitted without license from IHS

--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

ISA–TR20.00.01–2007Specification Forms for Process Measurement and Control Instruments Part 1: General Considerations

ISBN: 978-1-93756-000-3

Copyright 2011 by ISA. All rights reserved. Not for resale. Printed in the United States of America. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), without the prior written permission of the Publisher.

ISA67 Alexander Drive P. O. Box 12277 Research Triangle Park, North Carolina 27709 USA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

– 3 – ISA–TR20.00.01–2007

Copyright 2011 ISA. All rights reserved.

Preface

This preface, as well as all footnotes and annexes, is included for information purposes and is not part of ISA–TR20.00.01–2007.

The standards referenced within this document may contain provisions that, through reference in this text, constitute requirements of this document. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this document are encouraged to investigate the possibility of applying the most recent editions of the standards indicated within this document. Members of IEC and ISO maintain registers of currently valid International Standards. ANSI maintain registers of currently valid U.S. National Standards.

This document has been prepared as part of the service of ISA–The Instrumentation, Systems, and Automation Society, toward a goal of uniformity in the field of instrumentation. To be of real value, this document should not be static but should be subject to periodic review. Toward this end, the Society welcomes all comments and criticisms and asks that they be addressed to the Secretary, Standards and Practices Board; ISA; 67 Alexander Drive; P. O. Box 12277; Research Triangle Park, NC 27709; Telephone (919) 549-8411; Fax (919) 549-8288; E-mail: [email protected].

The ISA Standards and Practices Department is aware of the growing need for attention to the metric system of units in general, and the International System of Units (SI) in particular, in the preparation of instrumentation standards. The Department is further aware of the benefits to USA users of ISA standards of incorporating suitable references to the SI (and the metric system) in their business and professional dealings with other countries. Toward this end, this Department will endeavor to introduce SI-acceptable metric units in all new and revised standards, recommended practices, and technical reports to the greatest extent possible. Standard for Use of the International System of Units (SI): The Modern Metric System, published by the American Society for Testing & Materials as IEEE/ASTM SI 10-97, and future revisions, will be the reference guide for definitions, symbols, abbreviations, and conversion factors.

It is the policy of ISA to encourage and welcome the participation of all concerned individuals and interests in the development of ISA standards, recommended practices, and technical reports. Participation in the ISA standards-making process by an individual in no way constitutes endorsement by the employer of that individual, of ISA, or of any of the standards, recommended practices, and technical reports that ISA develops.

CAUTION — ISA ADHERES TO THE POLICY OF THE AMERICAN NATIONAL STANDARDS INSTITUTE WITH REGARD TO PATENTS. IF ISA IS INFORMED OF AN EXISTING PATENT THAT IS REQUIRED FOR USE OF THE STANDARD, IT WILL REQUIRE THE OWNER OF THE PATENT TO EITHER GRANT A ROYALTY-FREE LICENSE FOR USE OF THE PATENT BY USERS COMPLYING WITH THE STANDARD OR A LICENSE ON REASONABLE TERMS AND CONDITIONS THAT ARE FREE FROM UNFAIR DISCRIMINATION.

EVEN IF ISA IS UNAWARE OF ANY PATENT COVERING THIS STANDARD, THE USER IS CAUTIONED THAT IMPLEMENTATION OF THE STANDARD MAY REQUIRE USE OF TECHNIQUES, PROCESSES, OR MATERIALS COVERED BY PATENT RIGHTS. ISA TAKES NO POSITION ON THE EXISTENCE OR VALIDITY OF ANY PATENT RIGHTS THAT MAY BE INVOLVED IN IMPLEMENTING THE STANDARD. ISA IS NOT RESPONSIBLE FOR IDENTIFYING ALL PATENTS THAT MAY REQUIRE A LICENSE BEFORE IMPLEMENTATION OF THE STANDARD OR FOR INVESTIGATING THE VALIDITY OR SCOPE OF ANY PATENTS BROUGHT TO ITS ATTENTION. THE USER SHOULD CAREFULLY INVESTIGATE RELEVANT PATENTS BEFORE USING THE STANDARD FOR THE USER’S INTENDED APPLICATION.



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

ISA–TR20.00.01–2007 – 4 –


HOWEVER, ISA ASKS THAT ANYONE REVIEWING THIS STANDARD WHO IS AWARE OF ANY PATENTS THAT MAY IMPACT IMPLEMENTATION OF THE STANDARD NOTIFY THE ISA STANDARDS AND PRACTICES DEPARTMENT OF THE PATENT AND ITS OWNER.

ADDITIONALLY, THE USE OF THIS STANDARD MAY INVOLVE HAZARDOUS MATERIALS, OPERATIONS OR EQUIPMENT. THE STANDARD CANNOT ANTICIPATE ALL POSSIBLE APPLICATIONS OR ADDRESS ALL POSSIBLE SAFETY ISSUES ASSOCIATED WITH USE IN HAZARDOUS CONDITIONS. THE USER OF THIS STANDARD MUST EXERCISE SOUND PROFESSIONAL JUDGMENT CONCERNING ITS USE AND APPLICABILITY UNDER THE USER’S PARTICULAR CIRCUMSTANCES. THE USER MUST ALSO CONSIDER THE APPLICABILITY OF ANY GOVERNMENTAL REGULATORY LIMITATIONS AND ESTABLISHED SAFETY AND HEALTH PRACTICES BEFORE IMPLEMENTING THIS STANDARD.

The following people served as members of ISA Committee SP20:

NAME COMPANY

G. Barta, Chairman Bechtel Corp. W. Albe Dow Corning Corp. S. Alvarez Compania Inspeccion Mexicana T. Baldwin Brown & Root, Inc. N. Battikha Bergo Tech, Inc. E. Berger Mitre Corp. J. Carew Consultant T. Caston Eastman Chemicals Co. B. Cleary Rosemount, Inc. K. Cole Burns & Roe Enterprises E. Crawford Nova Control Systems, Inc. T. D. Daniel Consultant A. Engels Praxair, Inc. G. Erk Consultant F. Ford Bayer Corp. G. Gifford Flowserve R. Gulley Vara International R. Hartman Fisher-Rosemount Systems, Inc. C. Hill Brown & Root, Inc. H. Hinssen Exxon Chemical Engineering W. Ingham Stantec Consulting Ltd. A. Iverson Ivy Optiks D. Kelly VECO Rocky Mountain, Inc. H. Koning DSM Services M. Kulkarni General Instruments Consortium T. McAvinew Merrick & Co. A. McCauley Chagrin Valley Controls, Inc. J. McQuighan Constellation Energy J. Meppen Y. Meppen Consultants D. Osborn Greeley & Hansen C. Phillips Technip USA Corp. G. Ramachandran Cytec Industries, Inc. G. Richardson Thermco Instrument Corp. J. Rourke Jacobs Engineering Group P. Rowland SOIGNE Associates, Inc. G. Sanders Penberthy, Inc. M. Scott Process Measurement Tech. Ltd. J. Sen Bechtel Corp. R. Shah Consultant



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

– 5 – ISA–TR20.00.01–2007


J. Soos Huntsman Corp. M. Spencer Desktop Engineering Ltd. J. Summerfield Consultant R. Sundar Foster Wheeler USA Corp. L. Takeyasu Kenonic Controls, Inc. D. Taylor Spartan Controls R. Town Jefferson Services Co, Inc. I. Verhappen Syncrude Canada Ltd. E. Welch Duke/Fluor Daniel, Inc. B. Williams Merck & Co. Inc.

This technical report was approved for publication by the ISA Standards and Practices Board on 04 April 2001.

NAME COMPANY

M. Zielinski Fisher-Rosemount Systems, Inc. D. Bishop Consultant M. Cohen Consultant M. Coppler Ametek, Inc. B. Dumortier Schneider Electric W. Holland Southern Company E. Icayan Advanced Control & Engineering Solutions A. Iverson Ivy Optiks R. Jones Dow Chemical Co. V. Maggioli Feltronics Corp. T. McAvinew Merrick & Co. A. McCauley, Jr. Chagrin Valley Controls, Inc. G. McFarland Westinghouse Process Control Inc. D. Rapley Rapley Consulting Inc. R. Reimer Rockwell Automation J. Rennie Factory Mutual Research Corp. H. Sasajima Yamatake Corp. I. Verhappen Syncrude Canada Ltd. R. Webb Power Engineers W. Weidman Parsons Energy & Chemicals Group J. Weiss EPRIM. Widmeyer EG&G Defense Materials R. Wiegle CANUS Corp. C. Williams Eastman Kodak Co. G. Wood Graeme Wood Consulting



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

This page intentionally left blank.



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

– 7 – ISA–TR20.00.01–2007


Contents

Preface..........................................................................................................................................................3

Foreword .......................................................................................................................................................9

Introduction .................................................................................................................................................11

1 Scope...................................................................................................................................................13

2 Normative references...........................................................................................................................13

3 Definitions ............................................................................................................................................13

4 Application ...........................................................................................................................................13

4.1 Operating parameters documentation..........................................................................................13

4.2 Preliminary inquiry/quotation ........................................................................................................13

4.3 Traditional specification ................................................................................................................13

4.4 Conforming specification ..............................................................................................................13

5 Requirements.......................................................................................................................................14

5.1 Three form parts ...........................................................................................................................14

5.2 Form numbers and titles for Operating Parameters forms...........................................................14

5.3 Form numbers and titles for Device Specification forms..............................................................14

5.4 Form numbers and titles for General or Special Requirements forms .........................................14

6 General sections of ISA specification forms ........................................................................................14

6.1 Specification identification section................................................................................................14

6.2 Endorsements...............................................................................................................................14

6.3 Revision chronicle.........................................................................................................................14

6.4 Component identification ..............................................................................................................15

7 Classification and designation .............................................................................................................15

Annex A (informative) – Specification forms tables of contents..................................................................17

Annex B (informative) – Approved specification forms ...............................................................................23

Annex C (informative) – Specification forms pick list and contextual help references ..............................117



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\




--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

– 9 – ISA–TR20.00.01–2007


Foreword

This technical report has been prepared by ISA’s SP20 standards committee, Instrument Specification Forms. The ISA-SP20 committee welcomes comments and suggestions, and requests that they be addressed to the Chairperson, ISA-SP20, ISA, 67 Alexander Drive, Research Triangle Park, NC 27709 USA.

This technical report provides separate form parts for operating parameters, device specifications, and general requirements. Forms from ISA-20-1981 have been modified extensively, and many of the forms represent new devices not previously covered.

This technical report applies to all processes of development and use of ISA specification forms for process measurement and control instruments. It provides the listing of the forms, the classification of the devices, and the approved forms.



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\




--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

– 11 – ISA–TR20.00.01–2007


Introduction

The completion of instrument specification forms is an extremely important segment of the complete design, purchase, and manufacture of process measurement and control instrumentation.

Approved ISA specification forms for many devices are developed that follow the guidelines of ISA–20.00.03–2001 and have been reviewed by users and manufacturers. These forms are adequate for most applications and can be provided by ISA. The defining of specification forms and a data dictionary will allow electronic data exchange between users and manufacturers.

The purposes of ISA specification forms are

a) to assist in preparation of a complete specification by listing and providing space for all principal descriptive attributes;

b) to facilitate quoting, bid reviews, purchasing, receiving, calibration, inspection, piping design, design audit, accounting, and ordering procedures by uniform display of information;

c) to improve efficiency of instrumentation activities from initial concept to final commissioning and any subsequent reviews and revisions; and

d) to provide standard data definitions and field lengths adequate for electronic exchange of information.



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\




--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

– 13 – ISA–TR20.00.01–2007


1 Scope

Instrument devices with dedicated functionality may be specified using data-sheet-type, approved ISA specification forms. This technical report does not address system specifications such as shared control and shared display devices, where extensive use of functionality or performance specifications is required.

This technical report lists the ISA specification forms by form part category, measured or initiating variable, readout, or final control device categories, and form number. A form numbering system has been implemented that identifies the form categories, device function grouping, and page number. The form number, title, and development status is listed for each proposed or approved form.

2 Normative references

ISA–20.00.03–2001, Specification Forms for Process Measurement and Control Instruments, Part 3: Form Requirements and Development Guidelines.

3 Definitions

For the purpose of this technical report, the following definition applies:

3.1 specification form: the document, or its electronic data equivalent, that details the statement of parameters or properties prescribing the design basis, construction, materials, and performance for an instrument to be supplied.

4 Application

ISA specification forms may be used for the following different levels of device specification.

4.1 Operating parameters documentation

Documentation of the operating parameters may be completed and endorsed independently of the hardware device selection and preliminary specification through the use of the separate form page.

4.2 Preliminary inquiry/quotation

For a preliminary inquiry or quotation, the specifier and vendor may agree on a minimum level of information. In this case, the specifier may mark with an asterisk (*) in the revision column of the Operating Parameters or Device Specification forms, any lines that the recipient of the specification form is requested to complete.

4.3 Traditional specification

Documentation of operating parameters required for sizing or selection analysis, and identification of the instrument properties that are pertinent to the development of a manufacturer’s model number, should be the minimum data provided on specification forms used to purchase instruments.

4.4 Conforming specification

A complete specification ideally should include all relevant information about the main device and associated secondary devices that has been agreed to by the purchaser and supplier. In this case, the fully completed specification form can be used for the final documentation of the instrument specifications.



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

ISA–TR20.00.01–2007 – 14 –


5 Requirements

5.1 Three form parts

ISA specification forms are generally comprised of three form parts for the following information organization:

a) Operating Parameters forms are developed to document the process application and design conditions for communication to instrument specifiers and manufacturers.

b) Device Specification forms are developed to provide the information to initially size and select a main device and the information to identify requirements for attached and directly associated devices.

c) General or Special Requirements forms are developed to provide means for the specifier to identify general or special requirements that are applicable to the device, but need additional space beyond that available in the other two types of forms.

5.2 Form numbers and titles for Operating Parameters forms

A common form is developed for all devices sharing the same measured variable or final control element. Table A.1, annex A, identifies assigned categories, ISA form numbers, and titles.

5.3 Form numbers and titles for Device Specification forms

Device Specification forms are grouped and numbered based upon a device category code, the form part number, and an instrument function subcategory sequential number. Table A.2, annex A, identifies assigned device categories, ISA form numbers, and titles.

5.4 Form numbers and titles for General or Special Requirements forms

A single form is provided for the initial page of the General or Special Requirements forms. Table A.3, annex A, identifies the assigned ISA form number and title.

6 General sections of ISA specification forms

6.1 Specification identification section

Operating Parameters, Device Specification, and General or Special Requirements forms utilize the same specification identification field prompts.

6.2 Endorsements

Endorsement identifications and status inference, such as originator, checker, approver, and origin date, should be independent throughout each form type.

6.3 Revision chronicle

Identification of the three most recent entries recorded in the revision chronicle should be independent throughout each form type.



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

– 15 – ISA–TR20.00.01–2007


6.4 Component identification

Identification of the instrument, such as primary tag number, description, line/equipment number, and reference drawing number, should be identical throughout each form type.

7 Classification and designation

Hardware specification forms are based on specific hardware types as classified in annex A.



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\




--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

– 17 – ISA–TR20.00.01–2007


Annex A (informative) – Specification forms tables of contents

Table A.1 – Operating parameter device categories and form titles

Form Number Form Title Development Status, ISA-SP20

20A1001 Analysis Device Approved (Annex B)

20A1002 Analysis Device Composition or Property Approved (Annex B)

20B1001 Burner or Combustion Device

20C1001 Valve or Regulator Device Approved (Annex B)

20F1001 Flow Device Approved (Annex B)

20H1001 Hand Control Device

20L1001 Level Device Approved (Annex B)

20P1001 Differential Pressure Device Approved (Annex B)

20P1002 Pressure Safety Device Approved (Annex B)

20P1003 Pressure Device Rev. 0 Approved (Annex B)

20R1001 Receiver Device

20T1001 Temperature Device Approved (Annex B)

20U1001 Basic Engineering Design Data

20V1001 Vibration or Mechanical Analysis Device

20W1001 Weight or Force Device Approved (Annex B)

20X1001 Unclassified Device

20Y1001 Relay or Compute or Converter Device

20Z1001 Position Device

Table A.2 – Device specification categories and form titles


Analysis Devices

20A2101 Carbon Dioxide Monitor

20A2111 Combustible Gas Analyzer

20A2121 Flue & Stack Gas Analyzer

20A2141 Chromatograph Analyzer

20A2142 Chromatograph Analyzer Components

20A2151 In Situ Oxygen Analyzer

20A2161 Extractive Oxygen Analyzer

20A2162 Extractive Oxygen Analyzer Components



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

ISA–TR20.00.01–2007 – 18 –


Table A.2 – Device specification categories and form titles (cont'd)

Analysis Devices (cont'd)

20A2171 Opacity Analyzer

20A2181 Toxic Gas Analyzer

20A2391 Entrained Holdup Gas Monitor Approved (Annex B)

20A2191 Dissolved Oxygen Analyzer

20A2192 Dissolved Oxygen/Ozone/CL2 Transmitter/Analyzer/Monitor Approved (Annex B)

20A2201 Infrared or Ultraviolet Analyzer

20A2202 Infrared or Ultraviolet Analyzer Components

20A2301 Ion-Selective Analyzer

20A2311 Liquid Density or Specific Gravity Transmitter

20A2321 Nuclear-Type Density Transmitter

20A2331 Oil-In-Water Detector

20A2341 pH/ORP Sensor w/wo Insertion Assembly Approved (Annex B)

20A2342 pH/ORP/Conductivity/Resistivity Transmitter/Analyzer/Monitor Approved (Annex B)

20A2351 Turbidity or Suspended Solids Sensor w/wo Integral Transmitter Approved (Annex B)

20A2352 Turbidity or Suspended Solids Transmitter or Controller Approved (Annex B)

20A2361 Viscometer

20A2371 Moisture Analyzer

20A2372 Moisture Analyzer Components

20A2373 Humidity/Dewpoint Transmitter w/wo Switches Approved (Annex B)

20A2381 Conductivity Sensor w/wo Insertion Assembly Approved (Annex B)

20A2901 Sample Conditioning System w/wo Switches and Valves

Burner or Combustion Devices

20B2001 Flame Detector

20B2101 Flame Monitor

Valve or Regulator Devices

20C2001 Linear Motion Type Control Valve Assembly Approved (Annex B)

20C2002 Linear Motion Type Control Valve Auxiliaries Approved (Annex B)

20C2011 Rotary Motion Type Control Valve Assembly Approved (Annex B)

20C2012 Rotary Motion Type Control Valve Auxiliaries Approved (Annex B)

20C2021 Severe Service Control Valve Assembly

20C2022 Severe Service Control Valve Auxiliaries

20C2031 Desuperheater Control Valve

20C2041 Linear Motion Type Motor-Operated Valve Assembly Approved (Annex B)

20C2042 Rotary Motion Type Motor Operated Valve Assembly Approved (Annex B)



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

– 19 – ISA–TR20.00.01–2007



Valve or Regulator Devices (cont’d)

20C2043 Electric Actuator and Auxiliaries Approved (Annex B)

20C2101 Recirculation Control Valve

20C2111 Pressure Regulator with/without Pilot Valve Approved (Annex B)

20C2131 Temperature Regulator Valve

20C2141 Air-Release or Air/Vacuum and Combination Air Valves Approved (Annex B)

20C2201 Power-Actuated Block Valve Assembly

20C2202 Power-Actuated Block Valve Auxiliaries

20C2211 Solenoid Valve

20C2221 Manual-Actuated Block Valve Assembly

Flow Devices

20F2001 Anemometer Element

20F2011 Elbow Meter Approved (Annex B)

20F2021 Flow Nozzle w/wo Meter Tube Approved (Annex B)

20F2031 Orifice Plate Approved (Annex B)

20F2041 Orifice Plate Assembly w/wo Meter Tube Approved (Annex B)

20F2051 Multivariable Flow Transmitter Approved (Annex B)

20F2061 Paddle Flow Switch or Flowmeter Approved (Annex B)

20F2071 Pitot Tube w/wo Insertion Assembly Approved (Annex B)

20F2081 Segmental Wedge Flow Element Approved (Annex B)

20F2091 Target Flowmeter

20F2101 V-Shaped Cone Flow Element Approved (Annex B)

20F2111 Venturi or Flow Tube w/wo Meter Tube Approved (Annex B)

20F2211 Flume Flowmeter

20F2221 Open Channel Flowmeter

20F2231 Rotameter Flowmeter

20F2241 Rotameter Transmitter

20F2251 Variable Area Flowmeter

20F2261 Weir Flowmeter

20F2321 Magnetic Flowmeter w/wo Integral Totalizer Indicator Approved (Annex B)

20F2331 Nuclear Type Flowmeter

20F2341 Ultrasonic Flowmeter w/wo Switches Approved (Annex B)

20F2351 Thermal Mass Flowmeter w/wo Switches Approved (Annex B)

20F2361 Thermal Mass Flow Switch Approved (Annex B)



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

ISA–TR20.00.01–2007 – 20 –



Flow Devices (cont’d)

20F2371 Turbine Flowmeter w/wo Totalizer Indicator

20F2381 Vortex or Swirl Flowmeter w/wo Totalizer Indicator Approved (Annex B)

20F2391 Sonic Flowmeter Approved (Annex B)

20F2411 Positive Displacement Flowmeter Direct-Reading Type Approved (Annex B)

20F2421 Positive Displacement Flowmeter w/ Transmitter or Accessories Approved (Annex B)

20F2431 Variable Area Flow Switch

20F2511 Mass Type Flowmeter

20F2521 Coriolis Mass Flowmeter w/wo Totalizer Indicator Approved (Annex B)

20F2611 Sight Flow Indicator w/wo Illuminator Approved (Annex B)

Hand Control Devices

20H2001 Instrument Valve

20H2011 Instrument Manifold Valve

Level Devices

20L2101 Capacitance or RF Admittance Level Transmitter w/wo Switches Approved (Annex B)

20L2111 Differential Pressure Level Transmitter - Flange Mounted Approved (Annex B)

20L2121 Displacer-Type Level Transmitter or Local Controller Approved (Annex B)

20L2131 Tape Level Gauge or Transmitter w/wo Switches

20L2141 Nuclear Radiation Level Transmitter w/wo Switches Approved (Annex B)

20L2151 Resistance-Tape Level Transmitter w/wo Switches Approved (Annex B)

20L2161 Radar Level Transmitter w/wo Switches

20L2171 Non-contact Ultrasonic Level Transmitter w/wo Switches Approved (Annex B)

20L2181 Magnetostrictive Level Transmitter w/wo Switches

20L2301 Capacitance or RF Admittance Level Switch Approved (Annex B)

20L2311 Float or Displacer Level Switch Approved (Annex B)

20L2312 Tank Level Gauge or Indicator w/wo Switches Approved (Annex B)

20L2321 Nuclear Radiation Level Switch Approved (Annex B)

20L2331 Resistance Tape Level Switch

20L2341 RF or Radar or Micro Level Switch

20L2351 Ultrasonic Contact-Type Level Switch Approved (Annex B)

20L2361 Vibrating Element Level Switch

20L2371 Rotary Level Switch Approved (Annex B)

20L2501 Liquid Level Gage Glass w/wo Illuminator Approved (Annex B)

20L2511 Magnetic Liquid Level Gage or Indicator w/wo Switches Approved (Annex B)

20L2521 Tape Float Tank Gauge



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

– 21 – ISA–TR20.00.01–2007



Pressure or Differential Pressure Devices

20P2001 Pressure Gauge Approved (Annex B)

20P2011 Pressure Gauge With Diaphragm Seal Approved (Annex B)

20P2101 Differential Pressure Gauge Approved (Annex B)

20P2201 Pressure Transmitter Approved (Annex B)

20P2211 Pressure Transmitter With Diaphragm Seal Approved (Annex B)

20P2301 Differential Pressure Transmitter Approved (Annex B)

20P2311 Differential Pressure Transmitter With Diaphragm Seals Approved (Annex B)

20P2401 Pressure Switch w/wo Transmitter Approved (Annex B)

20P2501 Differential Pressure Switch w/wo Transmitter Approved (Annex B)

Pressure Safety Devices

20P2901 Rupture Disk Assembly w/wo Burst Sensor Approved (Annex B)

20P2911 Pressure Relief Tank Vent

20P2921 Pressure Relief Valve Approved (Annex B)

Receiver Devices

20R2011 Annunciator

20R2111 Controller

20R2121 Local Controller w/wo Recorder

20R2201 Receiver Gauge Approved (Annex B)

20R2211 Indicator

20R2221 Local Indicator w/wo Recorder

20R2231 Totalizer Indicator

20R2241 Digital Meter

20R2311 Analog Recorder

20R2411 Digital Recorder

Temperature Devices

20T2001 Bimetallic Thermometer w/wo Thermowell Approved (Annex B)

20T2101 Filled-System Thermometer Assembly w/wo Thermowell Approved (Annex B)

20T2111 Filled-System Temperature Switch w/wo Thermowell Approved (Annex B)

20T2121 Filled-System Temperature Transmitter w/wo Thermowell Approved (Annex B)

20T2201 RTD Assembly w/wo Thermowell Approved (Annex B)

20T2221 RTD/Thermocouple Temperature Transmitter or Switch Approved (Annex B)

20T2301 Thermocouple Assembly w/wo Thermowell Approved (Annex B)

20T2401 Thermal Radiation Temperature Sensor w/wo Monitor Approved (Annex B)

20T2501 Thermowell or Protecting Tube Assembly Approved (Annex B)



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

ISA–TR20.00.01–2007 – 22 –



Vibration or Mechanical Analysis Devices

20V2111 Vibration Switch

20V2211 Vibration Monitor

20V2311 Mechanical Analysis Monitor

Weight Devices

20W2011 Electronic Weight Scale

20W2111 Strain Gage Weight Indicator

20W2211 Load Cell or Transducer Approved (Annex B)

20W2221 Electronic Weight Transmitter, Indicator, or Controller Approved (Annex B)

Relay or Compute or Converter Devices

20Y2011 Transducer

20Y2111 Barrier or Isolator

20Y2211 Signal Converter

20Y2311 Analog Signal Switch

20Y2411 Solenoid or Pilot Valve

20Y2511 & 20Y2512 Fieldbus Junction & Continuation of Tag Number List Approved (Annex B)

Position Devices

20Z2011 Electromechanical Limit Switch Approved (Annex B)

20Z2012 Proximity Sensor Approved (Annex B)

20Z2021 Proximity Switch

20Z2111 Position Transmitter

Table A.3- General or special requirements form title


20G3001 General or Special Requirements Approved (Annex B)



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

– 23 – ISA–TR20.00.01–2007


Annex B (informative) – Approved specification forms

Following are the approved specification forms, as of the date of this publication.



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

1 RESPONSIBLE ORGANIZATION ANALYSIS DEVICE 6 SPECIFICATION IDENTIFICATIONS 2 7 Document no3 Operating Parameters 8 Latest revision Date4 9 Issue status5 10

11 ADMINISTRATIVE IDENTIFICATIONS 40 SERVICE IDENTIFICATIONS Continued 12 Project number Sub project no 41 Return conn matl type13 Project 42 Inline hazardous area cl Div/Zon Group14 Enterprise 43 Inline area min ign temp Temp ident number15 Site 44 Remote hazardous area cl Div/Zon Group16 Area Cell Unit 45 Remote area min ign temp Temp ident number17 4618 SERVICE IDENTIFICATIONS 4719 Tag no/Functional ident 48 COMPONENT DESIGN CRITERIA20 Related equipment 49 Component type

50 Component style2122

Service51 Output signal type

23 P&ID/Reference dwg 52 Characteristic curve24 Process line/nozzle no 53 Compensation style25 Process conn pipe spec 54 Type of protection26 Process conn nominal size Rating 55 Criticality code27 Process conn termn type Style 56 Max EMI susceptibility Ref 28 Process conn schedule no Wall thickness 57 Max temperature effect Ref 29 Process connection length 58 Max sample time lag30 Process line matl type 59 Max response time31 Fast loop line number 60 Min required accuracy Ref 32 Fast loop pipe spec 61 Avail nom power supply Number wires33 Fast loop conn nom size Rating 62 Calibration method34 Fast loop conn termn type Style 63 Testing/Listing agency35 Fast loop schedule no Wall thickness 64 Test requirements36 Fast loop estimated lg 65 Supply loss failure mode37 Fast loop material type 66 Signal loss failure mode38 Return conn nominal size Rating 6739 Return conn termn type Style 6869 PROCESS VARIABLES MATERIAL FLOW CONDITIONS 101 PROCESS DESIGN CONDITIONS 70 Flow Case Identification Units 102 Minimum Maximum Units71 Process pressure 10372 Process temperature 10473 Process phase type 10574 Process liquid actl flow 10675 Process vapor actl flow 10776 Process vapor std flow 10877 Process liquid density 10978 Process vapor density 11079 Process liquid viscosity 11180 Sample return pressure 11281 Sample vent/drain press 11382 Sample temperature 11483 Sample phase type 11584 Fast loop liq actl flow 11685 Fast loop vapor actl flow 11786 Fast loop vapor std flow 11887 Fast loop vapor density 11988 Conductivity/Resistivity 12089 pH/ORP 12190 RH/Dewpoint 12291 Turbidity/Opacity 12392 Dissolved oxygen 12493 Corrosivity 12594 Particle size 12695 12796 CALCULATED VARIABLES 12897 Sample lag time 12998 Process fluid velocity 13099 Wake/natural freq ratio 131

100 132133 MATERIAL PROPERTIES 137 MATERIAL PROPERTIES Continued 134 Name 138 NFPA health hazard Flammability Reactivity135 Density at ref temp At 139136 140

Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS

Form: 20A1001 Rev 0 © 2004 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

1 RESPONSIBLE ORGANIZATION ANALYSIS DEVICE 6 SPECIFICATION IDENTIFICATIONS 2 COMPOSITION OR PROPERTY 7 Document no3 Operating Parameters (Continued) 8 Latest revision Date4 9 Issue status5 10

11 PROCESS COMPOSITION OR PROPERTY MEASUREMENT DESIGN CONDITIONS 12 Component/Property Name Normal Units Minimum Units Maximum Units Repeatability13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 3839404142434445464748495051525354555657585960616263646566676869707172737475Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS

Form: 20A1002 Rev 0 © 2004 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

Form: 20C1001 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION VALVE OR REGULATOR DEVICE 6 SPECIFICATION IDENTIFICATIONS2 7 Document no3 Operating Parameters 8 Latest revision Date4 9 Issue status5 10

11 ADMINISTRATIVE IDENTIFICATIONS 40 SERVICE IDENTIFICATIONS Continued12 Project number Sub project no 41 Inline hazardous area cl Div/Zone Group13 Project 42 Inline area min ign temp Temp ident number14 Enterprise 43 Remote hazardous area cl Div/Zone Group15 Site 44 Remote area min ign temp Temp ident number16 Area Cell Unit 4517 4618 SERVICE IDENTIFICATIONS 47 COMPONENT DESIGN CRITERIA19 Tag no/Functional ident 48 Component type20 Related equipment 49 Component style

Service 50 Input signal type2122 51 Flow characteristic23 P&ID/Reference dwg number 52 Min seat leakage class24 Upstr line/nozzle number 53 Max stem leakage rate25 Upstream line pipe spec 54 Type of protection26 Upstr line nominal size Rating 55 Criticality code27 Upstr line conn type Style 56 Max EMI susceptibility Ref28 Upstr line schedule no Wall thickness 57 Min xdcr reqd accuracy Ref29 Upstr conn orientation 58 Max offset/propn band30 Upstr line material type 59 Actuator sizing factor31 Connection design code 60 Avail nom power supply Number wires32 Dnstr line/nozzle number 61 Available nom air supply33 Downstream line pipe spec 62 Testing/Listing agency34 Dnstr line nominal size Rating 63 Test requirements35 Dnstr line conn type Style 64 Supply loss failure mode36 Dnstr line schedule no Wall thickness 65 Signal loss failure mode37 Dnstr conn orientation 6638 Dnstr line material type 6739 Dnstr insulation atten 6869 PROCESS VARIABLES MATERIAL FLOW CONDITIONS 101 PROCESS DESIGN CONDITIONS70 Flow Case Identification Units 102 Minimum Maximum Units71 Inlet pressure 10372 Outlet pressure 10473 Inlet temperature 10574 Inlet phase type 10675 Mass fraction vapor 10776 Total mass flow rate 10877 Liquid mass flow rate 10978 Liquid actual flow rate 11079 Liquid standard flow rate 11180 Liquid density 11281 Liquid specific gravity 11382 Liquid viscosity 11483 Absolute vapor pressure 11584 Vapor mass flow rate 11685 Vapor actual flow rate 11786 Vapor standard flow rate 11887 Vapor density 11988 Vapor specific gravity 12089 Vapor molecular weight 12190 Vapor viscosity 12291 Inlet compressibility 12392 12493 CALCULATED VARIABLES 12594 Pressure differential 12695 Total system press drop 12796 Calculated flow coef 12897 Calculated travel 12998 Calculated travel time 13099 Calculated SPL 131

100 132

133 MATERIAL PROPERTIES 138 MATERIAL PROPERTIES Continued134 Name 139 Abs critical pressure135 Composition 140 Critical temperature136 Density at ref temp At 141 NFPA health hazard Flammability Reactivity137 Ratio sp heat capacity 142




--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

1 RESPONSIBLE ORGANIZATION FLOW DEVICE 6 SPECIFICATION IDENTIFICATIONS 2 7 Document no 3 Operating Parameters 8 Latest revision Date4 9 Issue status 5 10

11 ADMINISTRATIVE IDENTIFICATIONS 40 SERVICE IDENTIFICATIONS Continued 12 Project number Sub project no 41 Inline hazardous area cl Div/Zone Group13 Project 42 Inline area min ign temp Temp ident number14 Enterprise 43 Remote hazardous area cl Div/Zone Group15 Site 44 Remote area min ign temp Temp ident number16 Area Cell Unit 45 17 46 18 SERVICE IDENTIFICATIONS 47 COMPONENT DESIGN CRITERIA19 Tag no/Functional ident 48 Component type 20 Related equipment 49 Component style

50 Output signal type 2122

Service 51 Characteristic curve

23 P&ID/Reference dwg number 52 Compensation style 24 Upstr line/nozzle number 53 Type of protection 25 Upstream line pipe spec 54 Criticality code 26 Upstr line nominal size Rating 55 Max EMI susceptibility Ref 27 Upstr line conn type Style 56 Max temperature effect Ref 28 Upstr line schedule no Wall thickness 57 Min diameter ratio (d/D) Max29 Upstr conn orientation 58 Max response time 30 Upstr line material type 59 Min required accuracy Ref 31 Connection design code 60 Avail nom power supply Number wires32 Dnstr line/nozzle number 61 Min load capability33 Downstream line pipe spec 62 Testing/Listing agency34 Dnstr line nominal size Rating 63 Test requirements 35 Dnstr line conn type Style 64 Supply loss failure mode 36 Dnstr line schedule no Wall thickness 65 Signal loss failure mode 37 Dnstr conn orientation 66 38 Dnstr line material type 67 39 Avail upstr straight lg Dnstr lg 68 69 PROCESS VARIABLES MATERIAL FLOW CONDITIONS 101 PROCESS DESIGN CONDITIONS 70 Flow Case Identification Units 102 Minimum Maximum Units71 Inlet pressure 103 72 Outlet pressure 104 73 Inlet temperature 105 74 Inlet phase type 106 75 Mass fraction vapor 107 76 Total mass flow rate 108 77 Liquid mass flow rate 109 78 Liquid actual flow rate 110 79 Liquid standard flow rate 111 80 Liquid density 112 81 Liquid specific gravity 113 82 Liquid viscosity 11483 Absolute vapor pressure 115 84 Vapor mass flow rate 116 85 Vapor actual flow rate 117 86 Vapor standard flow rate 118 87 Vapor density 119 88 Vapor specific gravity 120 89 Vapor molecular weight 121 90 Vapor viscosity 122 91 Inlet compressibility 123 92 124 93 CALCULATED VARIABLES 12594 Pressure differential 12695 Perm pressure drop 12796 Line fluid velocity 128 97 Line Reynolds number 129 98 Calculated uncertainty 13099 131

132 MATERIAL PROPERTIES 138 MATERIAL PROPERTIES Continued 133 Name 139 Abs critical pressure 134 Composition 140 Critical temperature 135 Density at ref temp At 141 NFPA health hazard Flammability Reactivity136 Ratio sp heat capacity 142 137 Conductivity 143

Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS Form: 20F1001 Rev 0 © 2001 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

Form: 20L1001 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION LEVEL DEVICE 6 SPECIFICATION IDENTIFICATIONS2 7 Document no3 Operating Parameters 8 Latest revision Date4 9 Issue status5 10

11 ADMINISTRATIVE IDENTIFICATIONS 43 SERVICE IDENTIFICATIONS Continued12 Project number Sub project no 44 Process conn diff height13 Project 45 Zero datum height14 Enterprise 46 Turbulence intensity

15 Site 47 Inline hazardous area cl Div/Zone Group16 Area Cell Unit 48 Inline area min ign temp Temp ident number17 49 Remote hazardous area cl Div/Zone Group18 SERVICE IDENTIFICATIONS 50 Remote area min ign temp Temp ident number19 Tag no/Functional ident 5120 Related equipment 5221 Service 5322 54 COMPONENT DESIGN CRITERIA23 P&ID/Reference dwg number 55 Component type24 Upper conn nozzle number 56 Component style25 Upper conn pipe spec 57 Output signal type26 Upper conn nominal size Rating 58 Characteristic curve27 Upper conn termn type Style 59 Compensation required28 Upper conn schedule no Wall thickness 60 Type of protection29 Upper conn length 61 Criticality code30 Upper conn orientation 62 Max EMI susceptibility Ref31 Upper conn material type 63 Max temperature effect Ref32 Connection design code 64 Max response time33 Lower conn nozzle number 65 Min required accuracy Ref34 Lower conn pipe spec 66 Max dead band35 Lower conn nominal size Rating 67 Avail nom power supply Number wires36 Lower conn termn type Style 68 Min load capability37 Lower conn schedule no Wall thickness 69 Testing/Listing agency38 Lower conn length 70 Test requirements39 Lower conn orientation 71 Supply loss failure mode40 Lower conn material type 72 Signal loss failure mode41 Device insertion length 7342 Vessel nominal diameter Height 7475 PROCESS VARIABLES PROCESS DESIGN CONDITIONS76 Condition Identification Minimum Normal Maximum Units77 Pressure78 Temperature79 Lower material phase type80 Lower material density81 Lower material sp gr82 Lower material viscosity83 Lower material level84 Upper material phase type85 Upper material density86 Upper material sp gr87 Upper material viscosity88 Upper material level89 Max material buildup thkns90 Solids concentration91 Moisture content92 Max angle of repose93 Particle size949596 CALCULATED VARIABLES97 Calc zero el/suppr98 Calc measurement span99

100101 MATERIAL PROPERTIES 109 MATERIAL PROPERTIES Continued102 Lower material name 110 Upper material name103 Lower matl composition 111 Upper matl composition104 Lower matl density at ref At 112 Upper matl density at ref At105 Lower dielectric constant At temp 113 Upper dielectric constant At temp106 Lower material Color 114 Upper material Color107 Lower NFPA health hazard Flammability Reactivity 115 Upper NFPA health hazard Flammability Reactivity108 116




--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

1 RESPONSIBLE ORGANIZATION DIFFERENTIAL PRESSURE DEVICE 6 SPECIFICATION IDENTIFICATIONS 2 7 Document no 3 Operating Parameters 8 Latest revision Date4 9 Issue status 5 10

11 ADMINISTRATIVE IDENTIFICATIONS 42 SERVICE IDENTIFICATIONS Continued 12 Project number Sub project no 43 Process conn diff length 13 Project 44 Zero datum conn length 14 Enterprise 45 Inline hazardous area cl Div/Zone Group15 Site 46 Inline area min ign temp Temp ident number16 Area Cell Unit 47 Remote hazardous area cl Div/Zone Group17 48 Remote area min ign temp Temp ident number18 SERVICE IDENTIFICATIONS 49 19 Tag no/Functional ident 50 20 Related equipment 51

52 COMPONENT DESIGN CRITERIA2122

Service 53 Component type

23 P&ID/Reference dwg number 54 Component style 24 High side line/nozzle no 55 Output signal type 25 High side conn pipe spec 56 Characteristic curve 26 High side conn nom size Rating 57 Type of protection 27 High side conn termn type Style 58 Criticality code 28 High side conn schedule Wall thickness 59 Max EMI susceptibility Ref 29 High side conn length 60 Max temperature effect Ref 30 High side conn orient 61 Max response time 31 High side conn matl type 62 Min required accuracy Ref 32 Connection design code 63 Max dead band 33 Low side line/nozzle no 64 Avail nom power supply Number wires34 Low side conn pipe spec 65 Min load capability35 Low side conn nom size Rating 66 Testing/Listing agency36 Low side conn termn type Style 67 Test requirements 37 Low side conn schedule no Wall thickness 68 Supply loss failure mode 38 Low side conn length 69 Signal loss failure mode 39 Low side conn orientation 70 40 Low side conn matl type 71 41 Device insertion length 72 73 PROCESS VARIABLES MATERIAL FLOW CONDITIONS 102 PROCESS DESIGN CONDITIONS 74 Condition Identification Units 103 Minimum Maximum Units75 High side pressure 104 76 High side temperature 105 77 High side matl phase type 106 78 High side density 107 79 High side specific gravity 108 80 High side matl viscosity 109 81 Low side pressure 110 82 Low side temperature 111 83 Low side matl phase type 11284 Low side density 113 85 Low side specific gravity 114 86 Low side matl viscosity 115 87 Differential pressure 116 88 117 89 118 90 119 91 120 92 121 93 122 94 123 95 124 96 CALCULATED VARIABLES 12597 Calc zero el / suppr 12698 Calc measurement span 12799 128

100 129 101 130 131 MATERIAL PROPERTIES 137 MATERIAL PROPERTIES Continued 132 Low side material name 138 High side material name 133 Low side composition 139 High side composition 134 Low side density at ref At 140 High side density at ref At135 Low side NFPA health haz Flammability Reactivity 141 High side NFPA health haz Flammability Reactivity136 142

Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS Form: 20P1001 Rev 1 © 2007 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

1 RESPONSIBLE ORGANIZATION PRESSURE SAFETY DEVICE 6 SPECIFICATION IDENTIFICATIONS2 7 Document no3 Operating Parameters 8 Latest revision Date4 9 Issue status5 10

11 ADMINISTRATIVE IDENTIFICATIONS 39 SERVICE IDENTIFICATIONS Continued12 Project number Sub project no 40 Fire-fighting/Drainage13 Project 41 Inline hazardous area cl Div/Zone Group14 Enterprise 42 Inline area min ign temp Temp ident number15 Site 43 Remote hazardous area cl Div/Zone Group16 Area Cell Unit 44 Remote area min ign temp Temp ident number17 4518 SERVICE IDENTIFICATIONS 4619 Tag number 47 COMPONENT DESIGN CRITERIA20 Related equipment 48 Component type

49 Component style2122

Service50 Output signal type

23 P&ID/Reference dwg 51 Seat leakage class24 Fluid service 52 Type of protection25 Source of overpressure 53 Criticality code26 Inlet line/nozzle number 54 Set/Burst Pressure27 Inlet line pipe spec 55 Allowable SPL @ capacity28 Inlet line nominal size Rating 56 Preliminary selected area29 Inlet line conn type Style 57 Eff coef of discharge30 Inlet line material type 58 Disc combination factor31 Outlet line/nozzle number 59 Avail nom power supply Number wires32 Outlet line pipe spec 60 Required design code33 Outlet line nominal size Rating 61 Test requirements34 Outlet line conn type Style 62 Supply loss failure mode35 Outlet line material type 63 Signal loss failure mode36 Vessel wetted area 64 Calculations basis37 Vessel exposed area 6538 Environmental factor 6667 PROCESS VARIABLES MATERIAL FLOW CONDITIONS 98 PROCESS DESIGN CONDITIONS68 Flow Case Identification Non-fire Fire Capacity Units 99 Minimum Normal Maximum Units69 Allowable overpressure 10070 Inlet pressure 10171 Build-up back pressure 10272 Superimposed back press 10373 Inlet temperature 10474 Inlet density 10575 Inlet phase type vapor 10676 Mass fraction vapor 1.0 10777 Total mass flow rate 10878 Liquid mass flow rate 0 10979 Liquid actual flow rate 0 11080 Liquid density 11181 Liquid specific gravity 11282 Liquid viscosity 11383 Latent heat vaporization 11484 Vapor mass flow rate 11585 Vapor actual flow rate 11686 Vapor standard flow rate 11787 Vapor density 11888 Vapor specific gravity 11989 Vapor molecular weight 12090 Compressibility factor 12191 12292 CALCULATED VARIABLES 12393 Vaporized liquid rate 12494 Reqd eff discharge area 12595 Calculated SPL@ 3 ft 12696 Reaction force 12797 128

129 MATERIAL PROPERTIES 135 MATERIAL PROPERTIES Continued130 Name 136 Abs critical pressure131 Composition 137 Critical temperature132 Liquid specific heat 138 NFPA health hazard Flammability Reactivity133 Ratio sp heat capacity 139134 140


Form: 20P1002 Rev 0 © 2004 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

1 RESPONSIBLE ORGANIZATION PRESSURE DEVICE 6 SPECIFICATION IDENTIFICATIONS 2 7 Document no 3 Operating Parameters 8 Latest revision Date4 9 Issue status 5 10

11 ADMINISTRATIVE IDENTIFICATIONS 42 COMPONENT DESIGN CRITERIA 12 Project number Sub project no 43 Component type 13 Project 44 Component style 14 Enterprise 45 Output signal type 15 Site 46 Characteristic curve 16 Area Cell Unit 47 Type of protection 17 48 Criticality code 18 SERVICE IDENTIFICATIONS 49 Max EMI susceptibility Ref 19 Tag no/Functional ident 50 Max temperature effect Ref 20 Related equipment 51 Max response time

52 Min required accuracy Ref2122

Service 53 Max dead band

23 P&ID/Reference dwg number 54 Avail nom power supply Number wires24 Line/nozzle number 55 Min load capacity25 Process conn pipe spec 56 Testing/Listing agency26 Line/Nozzle nominal size Rating 57 Test requirements 27 Process conn termn type Style 58 Supply loss failure mode 28 Line/Nozzle schedule no Wall thickness 59 Signal loss failure mode 29 Connection length 60 30 Connection orientation 61 31 Line/Nozzle matl type 62 32 Connection design code 63 33 Device insertion length 64 34 Inline hazardous area cl Div/Zone Group 65 35 Inline area min ign temp Temp ident number 66 36 Remote hazardous area cl Div/Zone Group 67 37 Remote area min ign temp Temp ident number 68 38 69 39 70 40 71 41 72 73 PROCESS VARIABLES MATERIAL FLOW CONDITIONS 102 PROCESS DESIGN CONDITIONS 74 Condition Identification Units 103 Minimum Maximum Units75 Pressure 104 76 Temperature 105 77 Material phase type 10678 Liquid density 107 79 Liquid specific gravity 108 80 Liquid viscosity 109 81 Vapor density 110 82 Vapor specific gravity 111 83 Vapor viscosity 112 84 113 85 114 86 115 87 116 88 117 89 118 90 119 91 120 92 121 93 122 94 123 95 124 96 CALCULATED VARIABLES 12597 Calc zero el / suppr 12698 Calc measurement span 12799 128

100 129 101 130 131 MATERIAL PROPERTIES 137 MATERIAL PROPERTIES Continued 132 Material name 138 133 Composition 139 134 Density at ref At 140 135 NFPA health hazard Flammability Reactivity 141 136 142

Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS Form: 20P1003 Rev 0 © 2007 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

Form: 20T1001 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION TEMPERATURE DEVICE 6 SPECIFICATION IDENTIFICATIONS2 7 Document no3 Operating Parameters 8 Latest revision Date4 9 Issue status5 10

11 ADMINISTRATIVE IDENTIFICATIONS 39 SERVICE IDENTIFICATIONS Continued12 Project number Sub project no 40 Inline hazardous area cl Div/Zone Group13 Project 41 Inline area min ign temp Temp ident number14 Enterprise 42 Remote hazardous area cl Div/Zone Group15 Site 43 Remote area min ign temp Temp ident number16 Area Cell Unit 4417 4518 SERVICE IDENTIFICATIONS 46 COMPONENT DESIGN CRITERIA19 Tag no/Functional ident 47 Component type20 Related equipment 48 Component style

Service Output signal type2122

4950 Characteristic curve

23 P&ID/Reference dwg number 51 Type of protection24 Line/Nozzle number 52 Criticality code25 Process conn pipe spec 53 Max EMI susceptibility Ref26 Line/Nozzle nominal size Rating 54 Max temperature effect Ref27 Process conn termn type Style 55 Max response time28 Line/Nozzle schedule no Wall thickness 56 Min required accuracy Ref29 Connection length 57 Max dead band30 Connection orientation 58 Avail nom power supply Number wires31 Connection material type 59 Minimum load capability32 Connection design code 60 Testing/Listing agency33 Insulation thickness 61 Test requirements34 Device insertion length 62 Supply loss failure mode35 63 Signal loss failure mode36 6437 6538 6667 PROCESS VARIABLES MATERIAL FLOW CONDITIONS 100 PROCESS DESIGN CONDITIONS68 Flow Case Identification Units 101 Minimum Maximum Units69 Pressure 10270 Temperature 10371 Phase type 10472 Total mass flow rate 10573 Liquid mass flow rate 10674 Liquid actual flow rate 10775 Liquid standard flow rate 10876 Liquid density 10977 Liquid specific gravity 11078 Liquid viscosity 11179 Vapor mass flow rate 11280 Vapor actual flow rate 11381 Vapor standard flow rate 11482 Vapor density 11583 Vapor specific gravity 11684 Vapor molecular weight 11785 11886 11987 12088 12189 12290 12391 12492 12593 CALCULATED VARIABLES 12694 Line fluid velocity 12795 Line Reynolds number 12896 Wake/natural freq ratio 12997 13098 13199 132

133 MATERIAL PROPERTIES 138 MATERIAL PROPERTIES Continued134 Name 139 Ratio sp heat factor135 Composition 140 Emissivity136 Density at ref temp At 141 NFPA health hazard Flammability Reactivity137 Ratio sp heat capacity 142




--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

1 RESPONSIBLE ORGANIZATION WEIGHT OR FORCE DEVICE 6 SPECIFICATION IDENTIFICATIONS2 7 Document no3 Operating Parameters 8 Latest revision Date4 9 Issue status5 10

11 ADMINISTRATIVE IDENTIFICATIONS 40 SERVICE IDENTIFICATIONS Continued12 Project number Sub project no 41 Local hazardous area cl Div/Zone Group13 Project 42 Local area min ign temp Temp ident number14 Enterprise 43 Remote hazardous area cl Div/Zone Group15 Site 44 Remote area min ign temp Temp ident number16 Area Cell Unit 4517 4618 SERVICE IDENTIFICATIONS 47 COMPONENT DESIGN CRITERIA19 Tag no/Functional ident 48 Component type20 Related equipment 49 Component style

50 Output signal type2122

Service51 Characteristic curve

23 P&ID/Reference dwg number 52 Compensation style24 Washdown environment 53 Type of protection25 Vessel orientation 54 Criticality code26 Vessel nominal diameter 55 Max EMI susceptibility Ref27 Vessel overall height 56 Max response time28 Vessel support type 57 Min required accuracy Ref29 Qty vessel support points 58 Avail nom power supply Number wires30 Agitation type 59 Testing/Listing agency31 Piping connection style 60 Test requirements32 Vessel support material 61 Supply loss failure mode33 Seismic classification 62 Signal loss failure mode34 6335 6436 6537 6638 6739 6869 PROCESS VARIABLES PROCESS DESIGN CONDITIONS70 Condition Identification Minimum Maximum Units71 Temperature72 Dead load/empty weight73 Live load/content weight74 Tension force75767778798081828384858687888990919294 CALCULATED VARIABLES95 Seismic forces96 Wind forces979899

100 MATERIAL PROPERTIES 101 Name102 Material phase103 Density at ref temp At104 NFPA health hazard Flammability Reactivity105


Form: 20W1001 Rev 0 © 2004 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

1 RESPONSIBLE ORGANIZATION ENTRAINED/HOLDUP GAS MONITOR 6 SPECIFICATION IDENTIFICATIONS 2 7 Document no 3 Device Specification 8 Latest revision Date 4 9 Issue status 5 10

11 SENSOR HEAD COVER 56 TRANSMITTER OR TOTALIZER w/wo SWITCHES Continued 12 Head/Tube cover type 57 Data logger points 13 Cover style 58 Measurement compensation 14 Pipe/Tube nominal size 59 Enclosure material 15 Head cover material 60 16 Gasket/Seal material 61 17 62 18 63 PERFORMANCE CHARACTERISTICS19 SENSING ELEMENT 64 Min working temperature Max20 Measurement type 65 Gas fraction accuracy Ref21 Sensor style 66 Gas fraction repeatability Ref22 Band type 67 Gas fraction LRL URL23 Band material 68 Update rate 24 69 Min ambient working temp Max25 70 Contacts dc rating At max26 CONNECTION HEAD OR PREAMPLIFIER 71 Max sensor to receiver lg27 Configuration type 72 28 Output signal type 73 29 Enclosure type no/class 74 30 Signal conn termn style 7531 Cert/Approval type 7632 77 ACCESSORIES 33 LEAD WIRE AND EXTENSION 78 Mounting hardware 34 Extension type 79 Thermal blanket35 Cable length 80 36 Min cable operating temp Max 81 37 Signal termination type 82 38 Cert/Approval type 83 SPECIAL REQUIREMENTS39 Cable jacket material 84 Custom tag40 85 Reference specification 41 TRANSMITTER w/wo SWITCHES 86 Calibration report 42 Configuration type 87 Software configuration 43 Aux input signal type 88 44 Output signal type 89 45 Enclosure type no/class 90 46 Local operator interface 91 PHYSICAL DATA 47 Digital communication std 92 Estimated weight 48 Signal power source 93 Overall length 49 Contacts arrangement Quantity 94 Removal clearance 50 Integral indicator style 95 Outside diameter 51 Signal termination type 96 Signal conn nominal size Style52 Cert/Approval type 97 Mfr reference dwg53 Mounting location/type 9854 Failure/Diagnostic action 9955 Memory interface 10

110 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT OR SCALE 111 TAG NO/FUNCTIONAL MEAS/SIGNAL/SCALE LRV URV ACTION LRV URV112 Gas fraction-Output 1 113 Speed of sound-Output 2 114 -Freq output115 -Digital output 116 Gas fraction-Scale 1 117 Speed of sound-Scale 2 118 setpoint-Output 119 Failure signal-Output 120 121122123124 COMPONENT IDENTIFICATIONS 125 COMPONENT TYPE MANUFACTURER MODEL NUMBER 126 127 128 129 Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS

Form: 20A2391 Rev 0 © 2007 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

1 RESPONSIBLE ORGANIZATION DISSOLVED OXYGEN/OZONE/CL2 6 SPECIFICATION IDENTIFICATIONS2 TRANSMITTER/ANALYZER/MONITOR 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 TRANSMITTER OR ANALYZER 56 PERFORMANCE CHARACTERISTICS12 Housing type 57 pH compensation LRL URL13 Input sensor type 58 Meas 1 accuracy rating14 Input sensor style 59 Meas 2 accuracy rating15 Output signal type 60 Temp accuracy rating16 Enclosure type no/class 61 Measurement LRL URL17 Control mode 62 Temp compensation LRL URL18 Local operator interface 63 Barometric pressure LRL URL19 Characteristic curve 64 Minimum span Max20 Digital communication std 65 Min ambient working temp Max21 Signal power source 66 Contacts ac rating At max22 Temperature sensor type 67 Contacts dc rating At max23 Quantity of input sensors 68 Max distance to sensor lg24 Preamplifier location 6925 Contacts arrangement Quantity 7026 Integral indicator style 7127 Signal termination type 7228 Cert/Approval type 7329 Mounting location/type 7430 Failure/Diagnostic action 7531 Sensor diagnostics 76 ACCESSORIES32 Data history log 77 Remote indicator style33 Measurement compensation 78 Indicator enclosure34 Calibration function 79 Communicator style35 Enclosure material 8036 8137 8238 83 SPECIAL REQUIREMENTS39 84 Custom tag40 85 Reference specification41 86 Compliance standard42 87 Software configuration43 88 Software program44 8945 9046 9147 92 PHYSICAL DATA48 93 Estimated weight49 94 Overall height50 95 Removal clearance51 96 Signal conn nominal size Style52 97 Mfr reference dwg53 9854 9955 100

110 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT OR SCALE111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/SCALE LRV URV ACTION LRV URV112 Meas-Analog output 1113 Meas-Analog output 2114 Meas-Digital output115 Meas-Scale116 Temp-Scale117 Temp-Digital output118 Meas setpoint 1-Output119 Meas setpoint 2-Output120 Meas setpoint 3-Output121 Meas setpoint 4-Output122 Failure signal-Output123124 COMPONENT IDENTIFICATIONS125 COMPONENT TYPE MANUFACTURER MODEL NUMBER126127128129Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS

Form: 20A2192 Rev 0 © 2004 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

1 RESPONSIBLE ORGANIZATION pH/ORP SENSOR 6 SPECIFICATION IDENTIFICATIONS2 w/wo INSERTION ASSEMBLY 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 BODY HOLDER OR FITTING 60 INSERTION ASSEMBLY continued12 Body/Fitting type 61 Insertion/Immersion lg13 Process conn nominal size Rating 62 Valve body material14 Process conn termn type Style 63 Valve seat material15 Maximum probe diameter 64 Chamber wetted material16 Body/Fitting material 65 Compression ferrule matl17 Flange material 6618 Seal/O ring material 6719 68 PERFORMANCE CHARACTERISTICS20 69 Max press at design temp At21 70 Min working temperature Max22 SENSING ELEMENT 71 Min conductivity23 Sensor type 72 Max fluid velocity limit24 Construction style 73 Accuracy rating25 Measuring electrode shape 74 Measurement LRL URL26 Reference junction style 75 Temp compensation LRL URL27 Insertion/Immersion lg 76 Linearity28 Signal conn termn style 77 Max response time29 Temperature sensor type 78 Min ambient working temp Max30 Sensing surface matl 79 Max sensor to receiver lg31 Ref electrolyte material 8032 Ground pin material 8133 Reference element matl 8234 Primary junction matl 83 ACCESSORIES35 84 Electrolyte solution36 85 Buffer solution37 86 Cleaner type38 LEAD WIRE AND EXTENSION 87 Cleaner supply source39 Extension type 88 ORP std solution40 Cable length 89 Rotameter & valve41 Max cable operating temp 9042 Signal termination type 9143 Cable jacket material 92 SPECIAL REQUIREMENTS44 ` 93 Custom tag45 CONNECTION HEAD OR PREAMPLIFIER 94 Reference specification46 Configuration type 95 Compliance standard47 Temperature compensation 96 Calibration report48 Enclosure type no/class 9749 Signal termination type 9850 Cert/Approval type 9951 Mounting location/type 100 PHYSICAL DATA 52 Enclosure material 101 Estimated weight53 102 Overall height54 103 Removal clearance55 INSERTION ASSEMBLY 104 Signal conn nominal size Style56 Assembly type 105 Mfr reference dwg57 Isolation valve style 10658 Process conn nominal size Rating 10759 Process conn termn type Style 108

110 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/SCALE LRV URV LRV URV112 Measurement-Output signal113 Temp-Output signal114115116117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125


Form: 20A2341 Rev 0 © 2004 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

1 RESPONSIBLE ORGANIZATION pH/ORP/CONDUCTIVITY/RESISTIVITY 6 SPECIFICATION IDENTIFICATIONS2 TRANSMITTER/ANALYZER/MONITOR 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 TRANSMITTER OR ANALYZER 56 PERFORMANCE CHARACTERISTICS12 Housing type 57 Measurement accuracy13 Input sensor type 58 Temperature accuracy14 Input sensor style 59 Measurement LRL URL15 Output signal type 60 Temp compensation LRL URL16 Enclosure type no/class 61 Minimum span Max17 Control mode 62 Min ambient working temp Max18 Local operator interface 63 Contacts ac rating At max19 Characteristic curve 64 Contacts dc rating At max20 Digital communication std 65 Max sensor to receiver lg21 Signal power source 6622 Temperature sensor type 6723 Quantity of input sensors 6824 Preamplifier location 6925 Contacts arrangement Quantity 7026 Integral indicator style 7127 Signal termination type 7228 Cert/Approval type 7329 Mounting location/type 7430 Failure/Diagnostic action 7531 Sensor diagnostics 76 ACCESSORIES32 Data history log 77 Remote indicator style33 Temperature compensation 78 Indicator enclosure34 Calibration function 79 Communicator style35 Enclosure material 8036 8137 8238 83 SPECIAL REQUIREMENTS39 84 Custom tag40 85 Reference specification41 86 Compliance standard42 87 Software configuration43 88 Software program44 8945 9046 9147 92 PHYSICAL DATA 48 93 Estimated weight49 94 Overall height50 95 Removal clearance51 96 Signal conn nominal size Style52 97 Mfr reference dwg53 9854 9955 100

110 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT OR SCALE111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/SCALE LRV URV ACTION LRV URV112 Meas-Analog output 1113 Meas-Analog output 2114 Meas-Digital output115 Meas-Scale116 Temp-Scale117 Temp-Digital output118 Meas setpoint 1-Output119 Meas setpoint 2-Output120 Meas setpoint 3-Output121 Meas setpoint 4-Output122 Failure signal-Output123124 COMPONENT IDENTIFICATIONS125 COMPONENT TYPE MANUFACTURER MODEL NUMBER126127128129


Form: 20A2342 Rev 0 © 2004 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

1 RESPONSIBLE ORGANIZATION TURBIDITY OR SUSPENDED SOLIDS 6 SPECIFICATION IDENTIFICATIONS2 SENSOR w/wo INTEGRAL TRANSMITTER 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 BODY HOLDER OR FITTING 60 INSERTION ASSEMBLY continued12 Body/Fitting type 61 Valve body material13 Process conn nominal size Rating 62 Seal/O ring material14 Process conn termn type Style 63 Chamber wetted material15 Maximum probe diameter 6416 Body/Fitting material 6517 Seal/O ring material 66 PERFORMANCE CHARACTERISTICS18 67 Max press at design temp At19 68 Min working temperature Max20 69 Min flow rate limit Max21 SENSING ELEMENT 70 Max submersion depth22 Sensor type 71 Meas accuracy rating Ref23 Construction style 72 Measurement repeatability Ref24 Measurement wavelength 73 Measurement LRL URL25 Cleaning type 74 Temp compensation LRL URL26 Light source style 75 Max sensor to receiver lg27 Insertion/Immersion lg 7628 Temperature sensor type 7729 Measuring window matl 7830 7931 8032 8133 SIGNAL OR INTEGRAL TRANSMITTER 8234 Configuration type 8335 Output signal type 8436 Enclosure type no/class 85 ACCESSORIES37 Digital communication std 86 Calibration kit38 Signal power source 8739 Integral indicator style 8840 Signal termination type 8941 Cert/Approval type 9042 Mounting location/type 91 SPECIAL REQUIREMENTS43 Calibration function 92 Custom tag44 Enclosure material ` 93 Reference specification45 94 Compliance standard46 95 Calibration report47 LEAD WIRE AND EXTENSION 9648 Extension type 9749 Cable length 9850 Signal termination type 99 PHYSICAL DATA 51 Cable jacket material 100 Estimated weight52 101 Face-to-face dimension53 102 Overall length/height54 INSERTION ASSEMBLY 103 Removal clearance55 Assembly type 104 Signal conn nominal size Style56 Isolation valve style 105 Mfr reference dwg57 Process conn nominal size Rating 10658 Process conn termn type Style 10759 Insertion/Immersion lg 108

110 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/SCALE LRV URV ACTION LRV URV112 Meas-Analog 0utput 1113 Meas-Analog 0utput 2114 Temp-Output signal115116117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125


Form: 20A2351 Rev 0 © 2005 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

1 RESPONSIBLE ORGANIZATION TURBIDITY OR SUSPENDED SOLIDS 6 SPECIFICATION IDENTIFICATIONS 2 TRANSMITTER OR CONTROLLER 7 Document no 3 Device Specification 8 Latest revision Date4 9 Issue status 5 10

11 OPERATING PARAMETERS 53 PERFORMANCE CHARACTERISTICS 12 Project number Sub project no 54 Measurement accuracy Ref13 Project 55 Temperature accuracy14 Enterprise 56 Measurement repeatability Ref15 Site 57 Measurement LRL URL16 Area Cell Unit 58 Min ambient working temp Max17 Related equipment 59 Contacts ac rating At max18 60 Contacts dc rating At max19

Service 61

20 P&ID/Reference dwg Number 62 21 Remote hazardous area cl Div/Zone Group 63 22 Remote area min ign temp Temp ident number 64 23 65 24 66 25 TRANSMITTER OR INDICATOR OR CONTROLLER 67 26 Housing type 68 27 Input sensor/signal type 69 ACCESSORIES 28 Range selection style 70 Mounting hardware 29 Output signal type 71 Mating connector30 Enclosure type no/class 72 31 Control mode 73 32 Local operator interface 74 33 Characteristic curve 75 34 Digital communication std 76 SPECIAL REQUIREMENTS35 Signal power source 77 Custom tag 36 Temperature sensor type 78 Reference specification 37 Quantity of meas signals 79 Compliance standard 38 Aux input signal type 80 Software configuration 39 Contacts arrangement Quantity 81 Software program 40 Integral indicator style 82 41 Signal termination type 8342 Cert/Approval type 84 43 Mounting location/type 85 PHYSICAL DATA 44 Failure/Diagnostic action 86 Estimated weight 45 Sensor diagnostics 87 Overall width 46 Cleaning control type 88 Overall height 47 Measurement compensation 89 Overall depth 48 Calibration function 90 Signal conn nominal size Style49 Enclosure material 91 Mfr reference dwg 50 9251 93 52 94

110 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT OR SCALE 111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/SCALE LRV URV ACTION LRV URV112 Meas-Analog output 1 113 Meas-Analog output 2 114 Meas-Analog output 3 115 Temp-Output signal 116 Measurement-Scale 117 Temperature-Scale 118 Meas setpoint 1-Output 119 Meas setpoint 2-Output 120 Meas setpoint 3-Output 121 Meas setpoint 4-Output 122 Meas setpoint 5-Output 123 Meas setpoint 6-Output 124 Failure signal-Output125 126 COMPONENT IDENTIFICATIONS 127 COMPONENT TYPE MANUFACTURER MODEL NUMBER 128 129 130 131 132 Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS

Form: 20A2352 Rev 0 © 2005 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

1 RESPONSIBLE ORGANIZATION HUMIDITY/DEWPOINT TRANSMITTER 6 SPECIFICATION IDENTIFICATIONS2 w/wo SWITCHES 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 MOUNTING FITTING 60 PERFORMANCE CHARACTERISTICS12 Mounting/Fitting type 61 Max press at design temp At13 Process conn nominal size Rating 62 Min working temperature Max14 Process conn termn type Style 63 RH/Dewpoint accuracy15 Mounting/Fitting material 64 Temperature accuracy16 65 RH/Dewpoint repeatability17 66 Max response time18 67 Min ambient working temp Max19 SENSING ELEMENT 68 Contacts ac rating At max20 Sensor type 69 Contacts dc rating At max21 Probe style 70 Max sensor to receiver lg22 Temperature LRL URL 7123 Humidity/Dewpoint LRL URL 7224 Temperature sensor type 7325 Sensor protection style 7426 Probe length 7527 Sensor head material 7628 7729 7830 7931 LEAD WIRE AND EXTENSION 8032 Extension type 8133 RH/Dewpoint cable length 8234 Temperature cable length 83 ACCESSORIES35 Max cable operating temp 84 Calibrator36 Signal termination type 85 Humidity standards37 86 Replacement probe38 8739 8840 TRANSMITTER w/wo SWITCHES 8941 Housing type 90 SPECIAL REQUIREMENTS42 Output signal type 91 Custom tag43 Enclosure type no/class 92 Reference specification44 Local operator interface 93 Compliance standard45 Digital communication std 94 Calibration report46 Signal power source 95 Software configuration47 Qty of input sensors 9648 Contacts arrangement Quantity 9749 Integral indicator style 9850 Signal termination type 99 PHYSICAL DATA 51 Cert/Approval type 100 Estimated weight52 Mounting location/type 101 Overall width53 Calibration mode 102 Overall height54 Measurement compensation 103 Removal clearance55 Enclosure material 104 Signal conn nominal size Style56 105 Mfr reference dwg57 10658 10759 108

110 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT OR SCALE111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/SCALE LRV URV ACTION LRV URV112 Humidity-Analog output113114 Humidity-Scale 1115 Other variable-Scale 2116 Temp-Analog output117 Setpoint 1-Output118 Setpoint 2-Output119120 COMPONENT IDENTIFICATIONS121 COMPONENT TYPE MANUFACTURER MODEL NUMBER122123124125


Form: 20A2373 Rev 0 © 2004 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

1 RESPONSIBLE ORGANIZATION CONDUCTIVITY SENSOR 6 SPECIFICATION IDENTIFICATIONS2 w/wo INSERTION ASSEMBLY 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 BODY HOLDER OR FITTING 60 INSERTION ASSEMBLY continued12 Body/Fitting type 61 Chamber wetted material13 Process conn nominal size Rating 62 Compression ferrule matl14 Process conn termn type Style 6315 Body/Fitting material 6416 Flange material 65 PERFORMANCE CHARACTERISTICS17 Seal/O ring material 66 Max press at design temp At18 67 Min working temperature Max19 68 Cell constant accuracy20 69 Measurement LRL URL21 SENSING ELEMENT 70 Temp compensation LRL URL22 Sensor type 71 Max temp response time23 Construction style 72 Max sensor to receiver lg24 Nominal cell constant 7325 Temperature sensor type 7426 Bore diameter 7527 Insertion/Immersion lg 7628 Temp sensor location 7729 Insulator material 7830 Electrode material 7931 Ext shaft/support matl 8032 Sheath material 8133 8234 8335 8436 LEAD WIRE AND EXTENSION 85 ACCESSORIES37 Extension type 86 Conductivity standard38 Cable length 8739 Max cable operating temp 8840 Signal termination type 8941 Cable jacket material 9042 9143 CONNECTION HEAD 92 SPECIAL REQUIREMENTS44 Housing type 93 Custom tag45 Enclosure type no/class 94 Reference specification46 Signal termination type 95 Compliance standard47 Cert/Approval type 96 Calibration report48 Mounting location/type 9749 Enclosure material 9850 9951 INSERTION ASSEMBLY 100 PHYSICAL DATA 52 Assembly type 101 Estimated weight53 Isolation valve style 102 Overall height54 Process conn nominal size Rating 103 Removal clearance55 Process conn termn type Style 104 Signal conn nominal size Style56 Purge conn nominal size Style 105 Mfr reference dwg57 Insertion/Immersion length 10658 Valve body material 10759 Valve seat material 108

110 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/SCALE LRV URV LRV URV112 Measurement-Output signal113 Temp-Output signal114115116117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125


Form: 20A2381 Rev 0 © 2004 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

Form: 20C2001 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION LINEAR MOTION TYPE 6 SPECIFICATION IDENTIFICATIONS2 CONTROL VALVE ASSEMBLY 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 VALVE BODY AND BONNET 60 SIGNAL TRANSDUCER continued12 Body type 61 Enclosure type no/class13 Bonnet style 62 Digital communication std14 Inlet conn nominal size Rating 63 Signal power source15 Outlet conn nominal size Rating 64 Pressure gauges16 End conn termn type Style 65 Cert/Approval type17 Flange facing finish 66 Mounting location/type18 Stem seal type 67 Enclosure material19 Face-to-face standard 6820 Yoke boss diameter 69 POSITIONER OR CONTROLLER21 Body and bonnet material 70 Configuration type22 Lining material 71 Input signal type23 Body/Bonnet bolting matl 72 Enclosure type no/class24 Packing flg bolting matl 73 Signal power source25 Gasket material 74 Digital communication std26 Packing material 75 Cert/Approval type27 Bellows seal material 76 Pressure gauges28 77 By-pass manifold29 VALVE TRIM 78 Enclosure material30 Closure member type 7931 Trim style 80 PERFORMANCE CHARACTERISTICS32 Inherent characteristic 81 Max press at design temp At33 Seat ring type 82 Min working temperature Max34 Flow direction force 83 Max pressure drop35 Port/Orifice diameter 84 Rated flow coef type Coef Xt36 Stem diameter Rt travel 85 Rated factor Fl Sigma mr37 Closure member material 86 Rated seat leakage class38 Seat ring material 8739 Stem material 88 ACCESSORIES40 Cage material 89 Air set filter style41 Guide/Retainer material 90 Air set gauges42 Guide bushing material 91 Tubing nominal size43 Hard facing/coating 92 Tubing and fitting matl44 9345 ACTUATOR 94 SPECIAL REQUIREMENTS46 Actuator type 95 Custom tag47 Acting style 96 Reference specification48 Effective area 97 Special preparation49 Bench set LRL URL 98 Compliance standard50 Max supply capability 99 Construction code51 Handwheel type/position 100 Software configuration52 Casing/cylinder material 10153 Diaphragm/O ring matl 102 PHYSICAL DATA54 Yoke material 103 Estimated weight55 104 Face-to-face dimension56 SIGNAL TRANSDUCER 105 Overall height57 Input signal type 106 Removal clearance58 Output signal type 107 Mfr reference dwg59 Accuracy rating 108

110 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV ACTION LRV URV112 Bench set-Travel113 Positioner input-Travel114 Transducer input-Output115 Test pressure116117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

Form: 20C2002 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION LINEAR MOTION TYPE 6 SPECIFICATION IDENTIFICATIONS2 CONTROL VALVE AUXILIARIES 7 Document no3 Device Specification 8 Latest revision Date:4 9 Issue status5 10

11 POSITION SWITCHES 60 POSITION TRANSMITTER continued12 Housing type 61 Integral indicator style13 Sensor style 62 Signal termination type14 Output signal type 63 Cert/Approval type15 Enclosure type no/class 64 Mounting location/type16 Contacts ac rating At Max 65 Enclosure material17 Contacts dc rating At Max 6618 Contacts arrangement Quantity 6719 Integral indicator style 68 SUPPLY PRESSURE TRIP VALVE20 Signal termination type 69 Configuration type21 Cert/Approval type 70 Volume tank size22 Mounting location/type 71 Trip set pressure reset23 Enclosure material 72 Tank max working pressure24 Shaft material 73 Min supply capability Max25 Bushing material 74 Trip set pressure LRL URL26 Fastener material 75 Construction code27 Gasket/O ring material 76 Mounting location/type28 77 Body material29 78 Diaphragm/O ring material30 SOLENOID OR PILOT VALVE 7931 Body type 80 EMISSIONS MONITOR SWITCH32 Enclosure style 81 Sensor type33 Inlet conn nominal size Style 82 Housing type34 Coil watt rating 83 Inlet conn nominal size Style35 Coil insulation class 84 Output signal type36 Enclosure type no/class 85 Enclosure type no/class37 Min operating press diff Max 86 Contacts ac rating At Max38 Signal power source 87 Contacts dc rating At Max39 Manual operator type 88 Contacts arrangement40 Type of actuation 89 Integral indicator style41 Coil type 90 Signal termination type42 Operation style 91 Cert/Approval type43 Press port orifice size Exhaust port 92 Mounting location/type44 Signal termination type 93 Enclosure material45 Cert/Approval type 94 Diaphragm material46 Mounting location/type 9547 Enclosure material 9648 Body material 97 BOOSTER RELAY49 Seat/Disc/Diaphragm matl 98 Configuration type50 99 End conn nominal size Style51 100 Dead band rating52 POSITION TRANSMITTER 101 Max supply capability53 Housing type 102 Supply port size Exh port54 Sensor style 103 Body material55 Output signal type 104 Closure member matl56 Accuracy/Linearity rating 105 Diaphragm material57 Enclosure type no/class 106 Test conn material58 Digital communication std 107 Gasket/O ring material59 Signal power source 108

110 CALIBRATIONS AND TEST INPUT OR SETPOINT OUTPUT111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV ACTION LRV URV112 Position-Analog output113 Solenoid energized-Output114 Position setpoint-Output115 Supply setpoint–Output116 Emissions setpoint–Output117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120 Position transmitter121 Solenoid/Pilot valve122 Position switch123 Supply press trip valve124 Emissions monitor125 Booster relayRev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

1 RESPONSIBLE ORGANIZATION ROTARY MOTION TYPE 6 SPECIFICATION IDENTIFICATIONS 2 CONTROL VALVE ASSEMBLY 7 Document no 3 Device Specification 8 Latest revision Date4 9 Issue status 5 10

11 VALVE BODY AND BONNET 60 SIGNAL TRANSDUCER Continued 12 Body type 61 Enclosure type no/class 13 Bonnet style 62 Digital communication std 14 Inlet conn nominal size Rating 63 Signal power source 15 Outlet conn nominal size Rating 64 Pressure gauges 16 End conn termn type Style 65 Cert/Approval type 17 Flange facing finish 66 Mounting location/type 18 Shaft seal type 67 Enclosure material 19 Face-to-face standard 68 20 Yoke boss diameter 69 POSITIONER OR CONTROLLER21 Body and bonnet material 70 Configuration type 22 Lining material 71 Input signal type 23 Body/Bonnet bolting matl 72 Enclosure type no/class 24 Packing flg bolting matl 73 Signal power source 25 Gasket material 74 Digital communication std 26 Packing material 75 Cert/Approval type 27 76 Pressure gauges 28 77 By-pass manifold 29 VALVE TRIM 78 Enclosure material 30 Closure member type 79 31 Trim style 80 PERFORMANCE CHARACTERISTICS32 Inherent characteristic 81 Max press at design temp At33 Seal ring type 82 Min working temperature Max34 Flow direction force 83 Max pressure drop35 Shaft diameter Rated travel 84 Rated flow coef type Coef Xt36 Closure member material 85 Rated factor Fl Sigma mr37 Seal ring material 86 Rated seat leakage class 38 Shaft material 87 39 Flow ring material 88 ACCESSORIES 40 Guide/Retainer material 89 Air set filter style 41 Guide bushing material 90 Air set gauges 42 Hard facing/coating 91 Tubing nominal size 43 92 Tubing and fitting matl 44 93 45 ACTUATOR 94 SPECIAL REQUIREMENTS46 Actuator type 95 Custom tag47 Effective area 96 Reference specification 48 Bench set LRL URL 97 Special preparation 49 Max supply capability 98 Compliance standard 50 Handwheel type/position 99 Construction code 51 Mounting orientation 100 Software configuration 52 Casing/cylinder material 101 53 Diaphragm/O ring matl 102 PHYSICAL DATA 54 Yoke material 103 Estimated weight 55 104 Face-to-Face dimension 56 SIGNAL TRANSDUCER 105 Overall height 57 Input signal type 106 Removal clearance 58 Output signal type 107 Mfr reference dwg59 Accuracy rating 108

110 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT 111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV ACTION LRV URV112 Bench set-Travel 113 Positioner input-Travel 114 Transducer input-Output 115 Test pressure 116 117 118 COMPONENT IDENTIFICATIONS 119 COMPONENT TYPE MANUFACTURER MODEL NUMBER 120 121 122 123 124 125 Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS

Form: 20C2011 Rev 0 © 2001 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

Form: 20C2012 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION ROTARY MOTION TYPE 6 SPECIFICATION IDENTIFICATIONS2 CONTROL VALVE AUXILIARIES 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 POSITION SWITCHES 60 POSITION TRANSMITTER continued12 Housing type 61 Integral indicator style13 Sensor style 62 Signal termination type14 Output signal type 63 Cert/Approval type15 Enclosure type no/class 64 Mounting location/type16 Contacts ac rating At Max 65 Enclosure material17 Contacts dc rating At Max 6618 Contacts arrangement Quantity 6719 Integral indicator style 68 SUPPLY PRESSURE TRIP VALVE20 Signal termination type 69 Configuration type21 Cert/Approval type 70 Volume tank size22 Mounting location/type 71 Trip set pressure reset23 Enclosure material 72 Tank max working pressure24 Shaft material 73 Min supply capability Max25 Bushing material 74 Trip set pressure LRL URL26 Fastener material 75 Construction code27 Gasket/O ring material 76 Mounting location/type28 77 Body material29 78 Diaphragm/O ring material30 SOLENOID OR PILOT VALVE 7931 Body type 80 EMISSIONS MONITOR SWITCH32 Enclosure style 81 Sensor type33 Inlet conn nominal size Style 82 Housing type34 Coil watt rating 83 Inlet conn nominal size Style35 Coil insulation class 84 Output signal type36 Enclosure type no/class 85 Enclosure type no/class37 Min operating press diff Max 86 Contacts ac rating At Max38 Signal power source 87 Contacts dc rating At Max39 Manual operator type 88 Contacts arrangement40 Type of actuation 89 Integral indicator style41 Coil type 90 Signal termination type42 Operation style 91 Cert/Approval type43 Press port orifice size Exhaust port 92 Mounting location/type44 Signal termination type 93 Enclosure material45 Cert/Approval type 94 Diaphragm material46 Mounting location/type 9547 Enclosure material 9648 Body material 97 BOOSTER RELAY49 Seat/Disc/Diaphragm matl 98 Configuration type50 99 End conn nominal size Style51 100 Dead band rating52 POSITION TRANSMITTER 101 Max supply capability53 Housing type 102 Supply port size Exh port54 Sensor style 103 Body material55 Output signal type 104 Closure member matl56 Accuracy/Linearity rating 105 Diaphragm material57 Enclosure type no/class 106 Test conn material58 Digital communication std 107 Gasket/O ring material59 Signal power source 108

110 CALIBRATIONS AND TEST INPUT OR SETPOINT OUTPUT111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV ACTION LRV URV112 Position-Analog output113 Solenoid energized-Output114 Position setpoint-Output115 Supply setpoint-Output116 Emissions setpoint-Output117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120 Position transmitter121 Solenoid/Pilot valve122 Position switch123 Supply press trip valve124 Emissions monitor125 Booster relayRev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

Form: 20C2041 Rev 0 © 2007 ISA

1 RESPONSIBLE ORGANIZATION LINEAR MOTION TYPE 6 SPECIFICATION IDENTIFICATIONS2 MOTOR OPERATED VALVE ASSEMBLY 7 Document no 3 Device Specification 8 Latest revision Date4 9 Issue status 5 10

11 VALVE BODY AND BONNET 75 ACTUATOR Continuation 12 Body type 76 Motor contactor type 13 Bonnet style 77 Motor thermal protection 14 Inlet conn nominal size Rating 78 Motor phase protection 15 Outlet conn nominal size Rating 7916 End conn termn type Style 80 CONTROL MODULE17 Flange facing finish 81 Enclosure type 18 Stem seal type 82 Operation style 19 Face-to-face standard 83 Input signal type 20 Yoke boss diameter 84 Enclosure type no/class 21 Body and bonnet material 85 Control mode 22 Lining material 86 Digital communication std 23 Body/Bonnet bolting matl 87 Internal power supply24 Packing flg bolting matl 88 Space heater type 25 Gasket material 89 Output speed control 26 Packing material 90 Auxiliary control power27 Bellows seal material 91 Open/Close control 28 92 Local/Stop/Remote cont 29 VALVE TRIM 93 Local operator interface 30 Closure member type 94 Signal termination type 31 Trim style 95 Cert/Approval type32 Inherent characteristic 96 ESD control mode 33 Seat ring type 97 Failure/Diagnostic action 34 Flow direction force 98 Interlock/Inhibit mode 35 Port/Orifice diameter 99 Diagnostics capabilities 36 Stem diameter Rt travel 100 Motor reversal protection 37 Closure member material 101 Enclosure material 38 Seat ring material 102 Hardware material 39 Stem material 10340 Cage material 10441 Guide/Retainer material 105 POSITION SWITCH OR TRANSMITTER42 Guide bushing material 106 Output signal type 43 Hard facing/coating 107 Sensor style 44 108 Contacts ac rating At max45 GEAR REDUCER 109 Contacts dc rating At max46 Gear reducer type 110 Signal power source 47 Position lock style 111 Contacts arrangement Quantity48 Nominal size 112 Integral indicator style 49 Mounting base nom size Standard 113 Position light colors 50 Output nominal speed 11451 Handwheel gear ratio 115 TORQUE SWITCH OR TRANSMITTER52 Gearbox ratio 116 Output signal type 53 Rated output torque Thrust 117 Sensor style 54 Linear speed 118 Contacts ac rating At max55 Manual operator type 119 Contacts dc rating At max56 Stem coupling style 120 Signal power source 57 Stem nominal diameter Lead of screw 121 Contacts arrangement Quantity58 Handwheel diameter 122 Integral indicator style 59 Handwheel orientation 123 Protection feature 60 Travel stops 12461 Bevel pinion material 125 AUXILIARY INPUTS AND OUTPUTS62 Bevel gear matl 126 Configuration type 63 Housing material 127 Aux signal type 64 Bushing/Coupling/Nut matl 128 Output signal type 65 Lubricant material 129 Status contacts ac rating At max66 130 Status contacts dc rating At max67 131 Alarm contacts ac rating At max68 ACTUATOR 132 Alarm contacts dc rating At max69 Actuator type 133 Input signal power source 70 Motor style 134 Output signal pwr source 71 Motor nominal speed number of poles 135 Status contacts arr Quantity72 Power supply 136 Alarm contacts arr Quantity73 Insulation class rating 13774 Motor phase style 138Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

Form: 20C2041 Rev 0 © 2007 ISA

1 RESPONSIBLE ORGANIZATION LINEAR MOTION TYPE 6 SPECIFICATION IDENTIFICATIONS 2 MOTOR OPERATED VALVE ASSEMBLY 7 Document no 3 Device Specification 8 Latest revision Date4 9 Issue status 5 10

211 PERFORMANCE CHARACTERISTICS 246 PHYSICAL DATA 212 Max press at design temp At 247 Estimated weight 213 Min working temperature Max 248 Face-to-face dimension 214 Max pressure drop 249 Overall height 215 Maximum starts per hour 250 Removal clearance 216 Positioning accuracy Ref 251 Signal conn nominal size Style217 Position accuracy rating Ref 252 Mfr reference dwg218 Torque accuracy rating Ref 253 219 Torque adjustment LRL URL 254 220 Max starting current 255 221 Rated flow coef type Coef Xt 256222 Rated factor Fl Sigma mr 257223 Rated seat leakage class 258224 Max valve reqd torque Thrust 259225 Design life cycles 260226 Min ambient working temp Max 261227 262228 263229 ACCESSORIES 264230 Isolation switch 265231 Local control station 266232 Auxiliary power device 267233 268234 269235 SPECIAL REQUIREMENTS 270236 Custom tag 271237 Reference specification 272238 Special preparation 273239 Compliance standard 274240 Construction code 275241 Calculation report 276242 Software program 277243 Service design 278244 279245 280310 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT OR SCALE 311 TAG NO/FUNCTIONAL MEAS/SIGNAL/SCALE LRV URV ACTION LRV URV312 Position input-Travel 313 Close sw energized-Travel 314 Open sw energized-Travel 315 Position-Output 316 Torque-Output 317 Position-Scale 318 Aux input 1-Output 319 Aux input 2-Output 320 Aux input 3-Output 321 Aux input 4-Output 322 Position close sw-Output 323 Position open sw-Output 324 Torque close sw-Output 325 Torque open sw-Output 326 Aux output 1-Output 327 Aux output 2-Output 328 Aux output 3-Output 329 Aux output 4-Output 330 Failure signal-Output 331 332 COMPONENT IDENTIFICATIONS 333 COMPONENT TYPE MANUFACTURER MODEL NUMBER 334 335 336 337 338 Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

Form: 20C2042 Rev 0 © 2007 ISA

1 RESPONSIBLE ORGANIZATION ROTARY MOTION TYPE 6 SPECIFICATION IDENTIFICATIONS2 MOTOR OPERATED VALVE ASSEMBLY 7 Document no 3 Device Specification 8 Latest revision Date4 9 Issue status 5 10

11 VALVE BODY AND BONNET 75 ACTUATOR Continuation 12 Body type 76 Motor contactor type 13 Bonnet style 77 Motor thermal protection 14 Inlet conn nominal size Rating 78 Motor phase protection 15 Outlet conn nominal size Rating 7916 End conn termn type Style 80 CONTROL MODULE17 Flange facing finish 81 Enclosure type 18 Shaft seal type 82 Operation style 19 Face-to-face standard 83 Input signal type 20 Yoke boss diameter 84 Enclosure type no/class 21 Body and bonnet material 85 Control mode 22 Lining material 86 Digital communication std 23 Body/Bonnet bolting matl 87 Internal power supply24 Packing flg bolting matl 88 Space heater type 25 Gasket material 89 Output speed control 26 Packing material 90 Auxiliary control power27 91 Open/Close control 28 92 Local/Stop/Remote cont 29 VALVE TRIM 93 Local operator interface 30 Closure member type 94 Signal termination type 31 Trim style 95 Cert/Approval type32 Inherent characteristic 96 ESD control mode 33 Seal ring type 97 Failure/Diagnostic action 34 Flow direction force 98 Interlock/Inhibit mode 35 Shaft diameter Rt travel 99 Diagnostics capabilities 36 Closure member material 100 Motor reversal protection 37 Seal ring material 101 Enclosure material 38 Shaft material 102 Hardware material 39 Flow ring material 10340 Guide/Retainer material 10441 Guide bushing material 105 POSITION SWITCH OR TRANSMITTER42 Hard facing/coating 106 Output signal type 43 107 Sensor style 44 108 Contacts ac rating At max45 GEAR REDUCER 109 Contacts dc rating At max46 Gear reducer type 110 Signal power source 47 Position lock style 111 Contacts arrangement Quantity48 Nominal size 112 Integral indicator style 49 Mounting base nom size Standard 113 Position light colors 50 Output nominal speed 11451 Handwheel gear ratio 115 TORQUE SWITCH OR TRANSMITTER52 Gearbox ratio 116 Output signal type 53 Rated output torque Thrust 117 Sensor style 54 90 degree travel time 118 Contacts ac rating At max55 Manual operator type 119 Contacts dc rating At max56 Stem coupling style 120 Signal power source 57 Max stem capacity 121 Contacts arrangement Quantity58 Handwheel diameter 122 Integral indicator style 59 Handwheel orientation 123 Protection feature 60 Travel stops 12461 Worm/Spear material 125 AUXILIARY INPUTS AND OUTPUTS62 Worm/Helical gear matl 126 Configuration type 63 Housing material 127 Aux signal type 64 Bushing/Coupling/Nut matl 128 Output signal type 65 Lubricant material 129 Status contacts ac rating At max66 130 Status contacts dc rating At max67 131 Alarm contacts ac rating At max68 ACTUATOR 132 Alarm contacts dc rating At max69 Actuator type 133 Input signal power source 70 Motor style 134 Output signal pwr source 71 Motor nominal speed number of poles 135 Status contacts arr Quantity72 Power supply 136 Alarm contacts arr Quantity73 Insulation class rating 13774 Motor phase style 138Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

Form: 20C2042 Rev 0 © 2007 ISA

1 RESPONSIBLE ORGANIZATION ROTARY MOTION TYPE 6 SPECIFICATION IDENTIFICATIONS 2 MOTOR OPERATED VALVE ASSEMBLY 7 Document no 3 Device Specification 8 Latest revision Date4 9 Issue status 5 10

211 PERFORMANCE CHARACTERISTICS 246 PHYSICAL DATA 212 Max press at design temp At 247 Estimated weight 213 Min working temperature Max 248 Face-to-face dimension 214 Max pressure drop 249 Overall height 215 Maximum starts per hour 250 Removal clearance 216 Positioning accuracy Ref 251 Signal conn nominal size Style217 Position accuracy rating Ref 252 Mfr reference dwg218 Torque accuracy rating Ref 253 219 Torque adjustment LRL URL 254 220 Max starting current 255 221 Rated flow coef type Coef Xt 256222 Rated factor Fl Sigma mr 257223 Rated seat leakage class 258224 Max valve reqd torque Thrust 259225 Design life cycles 260226 Min ambient working temp Max 261227 262228 263229 ACCESSORIES 264230 Isolation switch 265231 Local control station 266232 Auxiliary power device 267233 268234 269235 SPECIAL REQUIREMENTS 270236 Custom tag 271237 Reference specification 272238 Special preparation 273239 Compliance standard 274240 Construction code 275241 Calculation report 276242 Software program 277243 Service design 278244 279245 280310 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT OR SCALE 311 TAG NO/FUNCTIONAL MEAS/SIGNAL/SCALE LRV URV ACTION LRV URV312 Position input-Travel 313 Close sw energized-Travel 314 Open sw energized-Travel 315 Position-Output 316 Torque-Output 317 Position-Scale 318 Aux input 1-Output 319 Aux input 2-Output 320 Aux input 3-Output 321 Aux input 4-Output 322 Position close sw-Output 323 Position open sw-Output 324 Torque close sw-Output 325 Torque open sw-Output 326 Aux output 1-Output 327 Aux output 2-Output 328 Aux output 3-Output 329 Aux output 4-Output 330 Failure signal-Output 331 332 COMPONENT IDENTIFICATIONS 333 COMPONENT TYPE MANUFACTURER MODEL NUMBER 334 335 336 337 338 Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

Form: 20C2043 Rev 0 © 2007 ISA

1 RESPONSIBLE ORGANIZATION ELECTRIC ACTUATOR 6 SPECIFICATION IDENTIFICATIONS2 AND AUXILIARIES 7 Document no 3 Device Specification 8 Latest revision Date4 9 Issue status 5 10

11 OPERATING PARAMETERS 75 ACTUATOR Continuation 12 Project number Sub project no 76 Motor contactor type 13 Project 77 Motor thermal protection 14 Enterprise 78 Motor phase protection 15 Site 7916 Area Cell Unit 80 CONTROL MODULE17 Driven component tag no 81 Enclosure type 18 Related equipment 82 Operation style 19 Service 83 Input signal type 20 84 Enclosure type no/class 21 P&ID/Reference dwg number 85 Control mode 22 Inline hazardous area cl Div/Zone Group 86 Digital communication std 23 Inline area min ign temp Temp ident number 87 Internal power supply24 Driven component type 88 Space heater type 25 Actuator sizing factor 89 Output speed control 26 90 Auxiliary control power 27 91 Open/Close control 28 MOUNTING HARDWARE AND LINKAGE 92 Local/Stop/Remote cont 29 Mounting/Linkage type 93 Local operator interface 30 Max torque rating 94 Signal termination type 31 Drive arm type 95 Cert/Approval type32 Driven arm type 96 ESD control mode 33 Rod end type 97 Failure/Diagnostic action 34 Drive arm size 98 Interlock/Inhibit mode 35 Driven arm size 99 Diagnostics capabilities 36 Pin hole/Tap size 100 Motor reversal protection 37 Mounting hole size 101 Enclosure material 38 Shaft conn size 102 Hardware material 39 Arm thickness 10340 Adapter style 10441 Mounting conn location 105 POSITION SWITCH OR TRANSMITTER42 Mounting hardware matl 106 Output signal type 43 Linkage material 107 Sensor style 44 108 Contacts ac rating At max45 GEAR REDUCER 109 Contacts dc rating At max46 Gear reducer type 110 Signal power source 47 Position lock style 111 Contacts arrangement Quantity48 Nominal size 112 Integral indicator style 49 Mounting base nom size Standard 113 Position light colors 50 Output nominal speed 11451 Handwheel gear ratio 115 TORQUE SWITCH OR TRANSMITTER52 Gearbox ratio 116 Output signal type 53 Rated output torque Thrust 117 Sensor style 54 Speed/90 ° travel time 118 Contacts ac rating At max55 Manual operator type 119 Contacts dc rating At max56 Stem coupling style 120 Signal power source 57 Stem nominal diameter Lead of screw 121 Contacts arrangement Quantity58 Handwheel diameter 122 Integral indicator style 59 Handwheel orientation 123 Protection feature 60 Travel stops 12461 Worm/Bevel pinion matl 125 AUXILIARY INPUTS AND OUTPUTS62 Worm/Bevel gear matl 126 Configuration type 63 Housing material 127 Aux signal type 64 Bushing/Coupling/Nut matl 128 Output signal type 65 Lubricant material 129 Status contacts ac rating At max66 130 Status contacts dc rating At max67 131 Alarm contacts ac rating At max68 ACTUATOR 132 Alarm contacts dc rating At max69 Actuator type 133 Input signal power source 70 Motor style 134 Output signal pwr source 71 Motor nominal speed number of poles 135 Status contacts arr Quantity72 Power supply 136 Alarm contacts arr Quantity73 Insulation class rating 13774 Motor phase style 138Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

Form: 20C2043 Rev 0 © 2007 ISA

1 RESPONSIBLE ORGANIZATION ELECTRIC ACTUATOR 6 SPECIFICATION IDENTIFICATIONS 2 AND AUXILIARIES 7 Document no 3 Device Specification 8 Latest revision Date4 9 Issue status 5 10

211 PERFORMANCE CHARACTERISTICS 246 PHYSICAL DATA 212 Maximum starts per hour 247 Estimated weight 213 Positioning accuracy Ref 248 Overall width 214 Position accuracy rating Ref 249 Overall height 215 Torque accuracy rating Ref 250 Overall depth 216 Torque adjustment LRL URL 251 Signal conn nominal size Style217 Max starting current 252 Mfr reference dwg218 Maximum required torque Thrust 253 219 Design life cycles 254 220 Min ambient working temp Max 255 221 256222 257223 ACCESSORIES 258224 Isolation switch 259225 Local control station 260226 Auxiliary power device 261227 262228 263229 264230 SPECIAL REQUIREMENTS 265231 Custom tag 266232 Reference specification 267233 Compliance standard 268234 Software program 269235 Service design 270236 Assembly responsibility 271237 272238 273239 274240 275241 276242 277243 278244 279245 280310 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT OR SCALE 311 TAG NO/FUNCTIONAL MEAS/SIGNAL/SCALE LRV URV ACTION LRV URV312 Position input-Travel 313 Close sw energized-Travel 314 Open sw energized-Travel 315 Position-Output 316 Torque-Output 317 Position-Scale 318 Aux input 1-Output 319 Aux input 2-Output 320 Aux input 3-Output 321 Aux input 4-Output 322 Position close sw-Output 323 Position open sw-Output 324 Torque close sw-Output 325 Torque open sw-Output 326 Aux output 1-Output 327 Aux output 2-Output 328 Aux output 3-Output 329 Aux output 4-Output 330 Failure signal-Output 331 332 COMPONENT IDENTIFICATIONS 333 COMPONENT TYPE MANUFACTURER MODEL NUMBER 334 335 336 337 338 Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

1 RESPONSIBLE ORGANIZATION PRESSURE REGULATOR 6 SPECIFICATION IDENTIFICATIONS 2 w/wo PILOT VALVE 7 Document no 3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 VALVE BODY AND LOWER CASING 64 PILOT REGULATOR continued 12 Body type 65 Body material13 Bonnet/Casing conn style 66 Spring case material14 Inlet conn nominal size Rating 67 Bolting material 15 Outlet conn nom size Rating 68 Seat ring material16 End conn termn type Style 69 Spring material17 Control conn nom size Style 70 Diaphragm material18 Control conn location 71 Closing cap material19 Body/Casing material 72 Gasket/Body seal matl20 Bolting material 73 Seat disk/O ring material21 Gasket/O ring material 74 Loading tubing material22 7523 7624 VALVE TRIM 77 PERFORMANCE CHARACTERISTICS25 Closure member type 78 Max Inlet press at temp At26 Trim style 79 Max outlet press at temp At27 Port/Orifice nominal size 80 Min working temp Max28 Closure member material 81 Min diff pressure Max29 Seat ring/Holder matl 82 Max case/Diaphragm press 30 Guide/Bushing material 83 Accuracy rating31 Stem material 84 Offset/Proportional band32 Seat disk/O ring material 85 Max overpressure Above33 Filter/Strainer material 86 Rated flow coef type Coef Xt34 87 Rated factor FL35 88 Wide-open flow coef 36 ACTUATOR AND SPRING CASE 89 Relief valve flow coef 37 Actuator type 90 Rated seat leakage class38 Housing style 91 Lockup Ref39 Actuator nominal size 9240 Vent/Load conn nom size Style 9341 Vent/Load conn location 94 ACCESSORIES 42 Pressure/Diff press LRL URL 95 Pressure gauge43 Adjuster type 96 Relief valve44 Control spring id 97 Line/Inlet strainer45 Relief spring ident 9846 Diaphragm nominal dia 9947 Vent assembly style 100 SPECIAL REQUIREMENTS48 Case vent orientation 101 Custom tag49 Integral relief style 102 Reference specification50 Spring case/Flange matl 103 Special preparation51 Diaphragm material 104 Compliance standard52 Relief valve seat matl 105 Cert/Approval type53 Spring material 106 Service design54 Closing cap material 10755 10856 109 PHYSICAL DATA 57 PILOT REGULATOR 110 Estimated weight58 Actuator type 111 Face-to-face dimension59 End conn nominal size Style 112 Overall height60 Adjuster type 113 Removal clearance61 Control spring id 114 Mfr reference dwg62 Diaphragm nominal dia 11563 Mounting location/type 116

120 CALIBRATIONS AND TEST INPUT OR SETPOINT 121 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/SCALE LRV URV122 Initial set pressure 123124125126 COMPONENT IDENTIFICATIONS127 COMPONENT TYPE MANUFACTURER MODEL NUMBER 128129130131


Form: 20C2111 Rev 0 © 2007 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

1 RESPONSIBLE ORGANIZATION AIR-RELEASE OR AIR/VACUUM 6 SPECIFICATION IDENTIFICATIONS 2 AND COMBINATION AIR VALVES 7 Document no 3 Device Specification 8 Latest revision Date4 9 Issue status 5 10

11 OPERATING PARAMETERS 64 AIR-RELEASE VALVE 12 Project number Sub project no 65 Body type 13 Project 66 Inlet conn nominal size Rating14 Enterprise 67 Inlet conn termn type Style15 Site 68 Outlet conn nominal size Rating16 Area Cell Unit 69 Outlet conn termn type Style17 Related equipment 70 Flushing conn nom size Style18 71 Closure member type 19

Service 72 Lever style

20 P&ID/Reference dwg 73 Mounting location/type 21 Upstream line number 74 Orifice size 22 Upstream line pipe spec 75 Body, cover & top matl 23 Upstr line nominal size Rating 76 Closure member matl 24 Upstr line conn type Style 77 Seat/Seal material 25 Upstr line schedule no Wall thickness 78 Float material 26 Upstr line material type 79 Trim material 27 Liq actl flow at max dr 80 Gasket/O ring material 28 Liq flow at air release 81 29 Liq actl flow at max fill 82 SURGE PROTECTION DEVICE30 Air std flow at max dr 83 Configuration type 31 Air flow at air release 84 Closure member style32 Air std flow at max fill 85 Nominal size 33 Press diff at max dr 86 Body material 34 Press diff at air release 87 Closure member matl 35 Press diff at max filling 88 36 Fluid vel at max filling 89 PERFORMANCE CHARACTERISTICS37 Material name 90 Max press at design temp At38 Density at ref temp At 91 Min working temperature Max39 NFPA health hazard Flammability Reactivity 92 Min working pressure Max40 93 Air release at max press At41 94 Rated air inflow at dp At42 95 Rated air outflow at dp At43 AIR/VACUUM VALVE BODY 96 Rated seat leakage 44 Body type 9745 Inlet conn nominal size Rating 98 ACCESSORIES 46 Inlet conn termn type Style 99 Back flush assembly47 Outlet conn nominal size Rating 100 Back flush valves 48 Outlet conn termn type Style 101 Isolation valve 49 Flushing conn nom size Style 102 Inlet piping assembly50 Body, cover & top matl 10351 Outlet protector material 104 SPECIAL REQUIREMENTS52 Gasket/O ring material 105 Custom tag53 106 Reference specification 54 107 Compliance standard 55 AIR/VACUUM VALVE TRIM 108 Cert/Approval type 56 Closure member type 109 Service design 57 Orifice style 11058 Closure member material 111 PHYSICAL DATA 59 Seat material 112 Estimated weight 60 Float material 113 Overall height 61 Trim material 114 Overall diameter/width 62 115 Mfr reference dwg63 116

117 CALIBRATIONS AND TEST TEST 118 TAG NUMBER TEST URV 119 Test pressure 120 121 122 123 COMPONENT IDENTIFICATIONS 124 COMPONENT TYPE MANUFACTURER MODEL NUMBER 125 126 127 128 Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS

Form: 20C2141 Rev 0 © 2005 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

1 RESPONSIBLE ORGANIZATION ELBOW FLOW METER 6 SPECIFICATION IDENTIFICATIONS 2 7 Document no 3 Device Specification 8 Latest revision Date4 9 Issue status 5 10

11 ELBOW FITTING 60 PERFORMANCE CHARACTERISTICS 12 Fitting type 61 Max press at design temp At13 Elbow nominal size 62 Min working temperature Max14 End conn nominal size Rating 63 Uncalibrated accuracy15 End conn termn type Style 64 Calibrated accuracy16 Elbow schedule number Wall thickness 65 Discharge coefficient 17 Press tap conn nom size Rating 66 Perm head loss at URL 18 Pressure tap conn type Style 67 19 High pressure tap location 68 20 Low pressure tap location 69 21 Discharge straight length 70 22 Fitting material 71 23 Flange material 72 24 73 25 74 26 75 27 FLOW CONDITIONER 76 28 Flow conditioner type 77 29 End conn nominal size Rating 78 30 Inlet conn termn type Style 79 31 Pipe/Tube schedule number 80 32 Outlet conn termn type 81 33 Pipe/Tube material 82 34 Flow conditioner material 83 35 Flange material 84 36 85 37 86 38 87 ACCESSORIES 39 ISOLATION VALVES AND FITTINGS 8840 Valve type 8941 End conn nominal size Rating 90 42 End conn termn type Style 91 SPECIAL REQUIREMENTS43 Connection fitting type 92 Custom tag44 Nipple nominal size 93 Reference specification 45 Valve body material 94 Compliance standard 46 Nipple material 95 Construction code 47 Connection fitting matl 96 Calibration report 48 Valve seal material 97 Special inspections 49 9850 9951 10052 101 PHYSICAL DATA 53 102 Estimated weight 54 103 Inlet to disch centerline 55 104 Outlet to inlet centerline 56 105 Mfr reference dwg57 10658 10759 108

110 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT 111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/SCALE LRV URV LRV URV112 Flow rate-Diff pressure 113 Test pressure 114115116117118 COMPONENT IDENTIFICATIONS 119 COMPONENT TYPE MANUFACTURER MODEL NUMBER 120 121 122 123 124 125

Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS Form: 20F2011 Rev 0 © 2007 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

Form: 20F2021 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION FLOW NOZZLE 6 SPECIFICATION IDENTIFICATIONS2 w/wo METER TUBE 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 BODY 60 PERFORMANCE CHARACTERISTICS12 Body type 61 Max press at design temp At13 Fabrication style 62 Min working temperature Max14 Process conn nominal size Rating 63 Uncalibrated accuracy15 End conn termn type Style 64 Perm head loss at URL16 Flange facing finish 6517 Pressure tap quantity 6618 Press tap conn nom size Style 6719 Stampings 6820 Nozzle material 6921 7022 7123 7224 THROAT 7325 Diameter ratio (Beta d/D) 7426 Throat diameter 7527 7628 7729 7830 METER TUBE 7931 Bore type 8032 End conn nominal size Rating 8133 End conn termn type Style 8234 Flange facing finish 8335 Upstream length 8436 Pipe schedule no 85 ACCESSORIES37 Downstream length 86 Purge system38 Coupling quantity 8739 Coupling nominal size Rating 8840 Coupling locations 8941 Internal bore diameter 9042 Flow straightener type 9143 Pipe/Tube material 92 SPECIAL REQUIREMENTS44 Flow straightener matl 93 Custom tag45 Bolting material 94 Reference specification46 Exterior coating material 95 Special preparation47 End termination material 96 Compliance standard48 Gasket material 97 Construction code49 Diffuser cone material 98 Calibration report50 99 Weld radiographs51 10052 101 PHYSICAL DATA53 102 Estimated weight54 103 Face-to-face dimension55 104 Removal clearance56 105 Mfr reference dwg57 10658 10759 108

110 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV LRV URV112 Flow rate–Diff pressure113 Test pressure114115116117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125




--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

Form: 20F2031Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION ORIFICE PLATE 6 SPECIFICATION IDENTIFICATIONS2 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 ORIFICE PLATE AND HOLDER 60 ACCESSORIES12 Plate type 61 Orifice holding block13 Holder/Seal unit style 62 Gasket set14 Nominal size 6315 API ring no 6416 Orifice flange nom rating 6517 Orifice bore type 66 SPECIAL REQUIREMENTS18 Orifice inlet edge style 67 Custom tag19 Diameter ratio (Beta d/D) 68 Reference specification20 Orifice bore diameter 69 Special preparation21 Plate outside diameter 70 Compliance standard22 Plate thickness 71 Calculation report23 Vent/Drain hole size 7224 Vent/Drain hole location 7325 Stampings required 74 PHYSICAL DATA26 Plate material 75 Estimated weight27 Seal material 76 Removal clearance28 Holder/Ring material 77 Mfr reference dwg29 7830 7931 8032 8133 8234 8335 8436 8537 8638 8739 8840 8941 9042 9143 9244 9345 9446 9547 9648 9749 9850 9951 10052 10153 10254 10355 10456 10557 10658 10759 108

110 CALIBRATIONS AND TEST INPUT OUTPUT111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV LRV URV112 Flow rate-Diff pressure113114115116117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

Form: 20F2041 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION ORIFICE PLATE ASSEMBLY 6 SPECIFICATION IDENTIFICATIONS2 w/wo METER TUBE 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 ORIFICE FLANGE OR FITTING 60 METER TUBE Continued12 Flange/Fitting type 61 Coupling locations13 Pressure tap style 62 Internal bore diameter14 End conn nominal size Rating 63 Flow straightener type15 End conn termn type Style 64 Pipe/Tube material16 Flange facing finish 65 Bolting material17 End conn schedule no 66 Exterior coating material18 Press tap conn nom size Style 67 End termination material19 Pressure tap orientation 68 Gasket material20 Tap connection plug type 6921 Centering/Dowel pins 7022 Jack screw material 7123 Flange/Fitting material 72 PERFORMANCE CHARACTERISTICS24 Trim material 73 Max press at design temp At25 Bolting material 74 Min working temperature Max26 Gasket material 7527 Lubrication material 7628 7729 7830 7931 ORIFICE PLATE AND HOLDER 8032 Plate type 8133 Holder/Seal unit style 8234 API ring no Rating 8335 Orifice bore type 84 ACCESSORIES36 Orifice inlet edge style 85 Orifice holding blocks37 Diameter ratio (Beta d/D) 8638 Orifice bore diameter 8739 Plate outside diameter 8840 Plate thickness 8941 Vent/Drain hole size 9042 Vent/Drain hole location 91 SPECIAL REQUIREMENTS43 Stampings 92 Custom tag44 Plate material 93 Reference specification45 Seal material 94 Special preparation46 Holder/Ring material 95 Compliance standard47 96 Construction code48 9749 9850 METER TUBE 9951 Bore type 100 PHYSICAL DATA52 End conn nominal size Rating 101 Estimated weight53 End conn termn category Style 102 Face-to-face dimension54 Flange facing finish 103 Overall height55 Upstream length 104 Removal clearance56 Pipe schedule no 105 Mfr reference dwg57 Downstream length 10658 Coupling quantity 10759 Coupling nominal size Rating 108

110 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV LRV URV112 Flow rate – Diff pressure113 Test pressure114115116117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

Form: 20F2051 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION MULTIVARIABLE FLOW TRANSMITTER 6 SPECIFICATION IDENTIFICATIONS2 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 TRANSMITTER BODY 60 PERFORMANCE CHARACTERISTICS12 Body/Flange type 61 Max press at design temp At13 Process conn nominal size Rating 62 Min working temp Max14 Process conn termn type Style 63 Diff press accuracy rating15 Vent/Drain location 64 Press accuracy rating16 Mounting type 65 Temp accuracy rating17 Body/Flange material 66 Diff press LRL URL18 Vent/Drain material 67 Press Lower Range-limit URL19 Bolting material 68 Fill fluid sp gr At temp20 Flange adapter material 69 Min ambient working temp Max21 Gasket/O ring material 7022 Mounting kit material 7123 7224 7325 7426 SENSING ELEMENT 7527 Detector type 7628 Min diff pressure span Max 7729 Min pressure span Max 7830 Temp input signal 7931 Diaphragm/Wetted material 8032 Fill fluid material 8133 8234 83 ACCESSORIES35 84 Remote indicator style36 TRANSMITTER 85 Heating kit style37 Output signal type 86 Manifold valve style38 Enclosure type no/class 87 Manifold material39 Characteristic curve 8840 Digital communication std 8941 Signal power source 90 SPECIAL REQUIREMENTS42 Transient protection 91 Custom tag43 Integral indicator style 92 Reference specification44 Signal termination type 93 Special preparation45 Cert/Approval type 94 Compliance standard46 Span-Zero adjust lct 95 Calibration report47 Failure/Diagnostic action 96 Software configuration48 Enclosure material 9749 9850 9951 100 PHYSICAL DATA52 101 Estimated weight53 102 Overall height54 103 Removal clearance55 104 Signal conn nominal size Style56 105 Mfr reference dwg57 10658 10759 108

110 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT OR SCALE111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/SCALE LRV URV ACTION LRV URV112 Flow rate-Analog output113 Flow rate-Scale114 Diff Press-Digital output115 Press-Digital output116 Temp-Digital output117 Flow rate-Digital output118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125




--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

1 RESPONSIBLE ORGANIZATION PADDLE FLOW SWITCH 6 SPECIFICATION IDENTIFICATIONS 2 OR FLOWMETER 7 Document no 3 Device Specification 8 Latest revision Date4 9 Issue status 5 10

11 BODY OR STEM FITTING 59 PERFORMANCE CHARACTERISTICS 12 Body/Fitting type 60 Max press at design temp At13 Process conn nominal size Rating 61 Min working temperature Max14 Process conn termn type Style 62 Accuracy rating Ref15 Seal type 63 Repeatability Ref16 Extension/Heat insulator 64 Incr flow adjustable LRL URL17 Body/Fitting material 65 Decr flow adjustable LRL URL18 Bellow/Flexure tube matl 66 Flow rate LRL URL19 Flange material 67 Maximum pressure drop20 Seal/O ring material 68 Min ambient working temp Max21 69 Contacts ac rating At max22 70 Contacts dc rating At max23 71 24 SENSING ELEMENT 72 25 Sensor type 73 26 Sensor style 7427 Paddle nominal size 7528 Integral cable length 7629 Mounting orientation 7730 Paddle/Plate material 7831 7932 8033 8134 SWITCH OR TRANSMITTER 8235 Housing type 83 ACCESSORIES 36 Element style 84 Mating connector37 Output signal type 85 Remote relay38 Enclosure type no/class 86 39 Setpoint adjustment type 87 40 Signal power source 88 41 Damping/Time delay style 89 SPECIAL REQUIREMENTS42 Contacts arrangement Quantity 90 Custom tag43 Integral indicator style 91 Reference specification44 Signal termination type 92 Compliance standard 45 Cert/Approval type 93 Service design 46 Enclosure material 94 47 95 48 96 49 97 PHYSICAL DATA 50 98 Estimated weight 51 99 Face-to-face dimension52 100 Overall height 53 101 Removal clearance 54 102 Signal conn nominal size Style55 103 Mfr reference dwg56 104 57 105 58 106

110 CALIBRATIONS AND TEST INPUT OR SETPOINT OUTPUT 111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/SCALE LRV URV ACTION LRV URV112 Flow setpoint 1-Output 113 Flow setpoint 2-Output 114 Flow setpoint 3-Output 115 Flow setpoint 4-Output 116 Flow setpoint 5-Output 117 Flow setpoint 6-Output 118 Flow rate-Scale 119 Flow rate- Analog output 120 121 COMPONENT IDENTIFICATIONS122 COMPONENT TYPE MANUFACTURER MODEL NUMBER 123 124 125 126 Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS

Form: 20F2061 Rev 0 © 2005 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

1 RESPONSIBLE ORGANIZATION PITOT TUBE 6 SPECIFICATION IDENTIFICATIONS2 w/wo INSERTION ASSEMBLY 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 BODY OR MOUNTING ASSEMBLY 60 PERFORMANCE CHARACTERISTICS12 Body/Assembly type 61 Max press at design temp At13 Sensor end support style 62 Min working temperature Max14 Process conn nominal size Rating 63 Uncalibrated accuracy15 Process conn termn type Style 64 Temp accuracy rating16 End support conn nom size Style 65 Flow repeatability17 Pipe spool schedule 66 Min Reynolds number18 Mounting fitting type 67 Rated flow coefficient K19 Body/Assembly material 6820 Packing material 6921 Mounting fitting matl 7022 7123 7224 SENSING ELEMENT 7325 Sensor type 7426 Nominal line size 7527 Sensor nominal size 7628 Temperature element type 7729 Sensor material 7830 7931 8032 CONNECTION HEAD AND VALVES 8133 Connection head type 8234 Connection head style 83 ACCESSORIES35 Process conn nominal size Rating 84 Manifold valve style36 Process conn termn type Style 85 Manifold valve material37 Press conn nominal size Style 8638 Pressure tap orientation 8739 Head orientation 8840 Connection valve style 8941 Head material 90 SPECIAL REQUIREMENTS42 Flange material 91 Custom tag43 Connection valve matl 92 Reference specification44 93 Special preparation45 94 Compliance standard46 95 Construction code47 INSERTION ASSEMBLY 96 Calibration report48 Insertion assembly type 97 Special inspections49 Isolation valve style 9850 Process conn nominal size Rating 9951 Process conn termn type Style 100 PHYSICAL DATA 52 Valve nom press rating 101 Estimated weight53 Valve body material 102 Face-to-face dimension54 Valve seat material 103 Overall height55 Wetted material 104 Removal clearance56 Packing material 105 Mfr reference dwg57 10658 10759 108

110 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/SCALE LRV URV LRV URV112 Flow rate-Diff pressure113 Test pressure114115116117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125


Form: 20F2071 Rev 0 © 2004 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

Form: 20F2081 Rev 0 © 2007 ISA

1 RESPONSIBLE ORGANIZATION SEGMENTAL WEDGE FLOW ELEMENT 6 SPECIFICATION IDENTIFICATIONS2 7 Document no 3 Device Specification 8 Latest revision Date 4 9 Issue status 5 10

11 BODY OR TUBE 60 PERFORMANCE CHARACTERISTICS 12 Body/Tube type 61 Max press at design temp At13 End conn nominal size Rating 62 Min working temperature Max14 End conn termn type Style 63 Uncalibrated accuracy Ref15 Pipe schedule no 64 Calibrated accuracy Ref16 Pressure tap quantity 65 Repeatability Ref17 Press tap conn nom size Rating 66 Rated flow coefficient 18 Press tap conn termn type Style 67 Perm head loss at URL 19 Temp tap conn nom size Rating 6820 Temp tap conn termn type Style 6921 Tube material 7022 Flange material 7123 Gasket material 7224 7325 7426 7527 INTERNAL COMPONENTS 7628 Element type 7729 H/D ratio 78 30 Wedge restriction matl 79 31 8032 81 ACCESSORIES 33 82 Mounting hardware 34 83 Manifold valve 35 84 Isolation valve36 85 Impulse line material 37 8638 87 39 8840 89 SPECIAL REQUIREMENTS 41 90 Custom tag 42 91 Reference specification43 92 Compliance standard 44 93 Construction code 45 94 Calibration report 46 95 Material certificate 47 96 Special inspection 48 97 Hydro static testing49 9850 9951 10052 101 PHYSICAL DATA53 102 Estimated weight 54 103 Overall length 55 104 Overall height 56 105 Mfr reference dwg57 10658 10759 108

110 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT111 TAG NUMBER MEAS/SIGNAL/TEST LRV URV LRV URV112 Flow rate – Diff pressure 113 Test pressure 114 115 116 117 118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER 120 121 122 123 124 125




--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

Form: 20F2101 Rev 0 © 2007 ISA

1 RESPONSIBLE ORGANIZATION V-SHAPED CONE FLOWMETER 6 SPECIFICATION IDENTIFICATIONS2 7 Document no 3 Device Specification 8 Latest revision Date 4 9 Issue status 5 10

11 BODY OR TUBE 60 PERFORMANCE CHARACTERISTICS 12 Body/Tube type 61 Max press at design temp At13 End conn nominal size Rating 62 Min working temperature Max14 End conn termn type Style 63 Uncalibrated accuracy Ref15 Flange facing finish 64 Calibrated accuracy Ref16 Pipe schedule no 65 Repeatability Ref17 Press tap conn nom size Rating 66 Rated flow coefficient 18 Press tap conn termn type Style 67 Perm head loss at URL 19 Tube material 6820 External treatment 6921 Flange material 7022 O ring material 7123 7224 7325 SENSING ELEMENT 7426 Element type 7527 Beta ratio 7628 Cone and support matl 7729 78 30 79 31 8032 81 33 82 34 83 35 84 ACCESSORIES 36 85 Mounting hardware 37 86 Manifold valve 38 8739 8840 89 41 90 SPECIAL REQUIREMENTS 42 91 Custom tag43 92 Reference specification 44 93 Conformance standard 45 94 Construction code 46 95 Calibration report 47 96 Material certificate 48 97 Special inspection 49 9850 9951 10052 101 PHYSICAL DATA53 102 Estimated weight 54 103 Overall length 55 104 Overall height 56 105 Mfr reference dwg57 10658 10759 108

110 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV LRV URV112 Flow rate – Diff pressure 113 Test pressure 114 115 116 117 118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER 120 121 122 123 124 125 Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

Form: 20F2111 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION VENTURI OR FLOW TUBE 6 SPECIFICATION IDENTIFICATIONS2 w/wo METER TUBE 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 BODY OR TUBE 60 PERFORMANCE CHARACTERISTICS12 Tube form 61 Max press at design temp At13 Fabrication style 62 Min working temperature Max14 Inlet conn nominal size Rating 63 Uncalibrated accuracy15 Outlet conn nominal size Rating 64 Perm head loss at URL16 End conn termn type Style 6517 Flange facing finish 6618 Pressure tap quantity 6719 Press tap conn nom size Rating 6820 Press tap conn type Style 6921 Press tap orientation 7022 Body/Tube material 7123 Bolting material 7224 Exterior coating material 7325 End termination material 7426 Gasket material 7527 7628 7729 7830 THROAT 7931 Mounting type 8032 Diameter ratio (beta d/D) 8133 Throat diameter 8234 Cone material 8335 Throat material 8436 85 ACCESSORIES37 86 Purge system38 87 Cleaner style39 METER TUBE 88 Valve style40 Bore type 89 Valves and Nipple matl41 End conn nominal size Rating 9042 End conn termn type Style 9143 Flange facing finish 92 SPECIAL REQUIREMENTS44 Upstream length 93 Custom tag45 Pipe schedule no 94 Reference specification46 Downstream length 95 Special preparation47 Coupling quantity 96 Compliance standard48 Coupling nominal size Rating 97 Construction code49 Coupling locations 98 Calibration report50 Internal bore diameter 99 Weld radiographs51 Flow straightener type 10052 Pipe/Tube material 101 PHYSICAL DATA53 Bolting material 102 Estimated weight54 Exterior coating material 103 Face-to-face dimension55 End termination material 104 Removal clearance56 Gasket material 105 Mfr reference dwg57 10658 10759 108

110 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV LRV URV112 Flow rate – Diff pressure113 Test pressure114115116117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125




--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

Form: 20F2321Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION MAGNETIC FLOWMETER 6 SPECIFICATION IDENTIFICATIONS2 w/wo INTEGRAL TOTALIZER INDICATOR 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 FLOWMETER BODY 60 TOTALIZER INDICATOR12 Body type 61 Totalizer type13 Flow tube style 62 Enclosure type no/class14 End conn nominal size Rating 63 Signal power source15 End conn termn type Style 64 Contacts arrangement Quantity16 Flow tube diameter Thickness 65 Totalizer reset style17 Hardware mounting kit 66 Integral indicator style18 Flow tube material 67 Cert/Approval type19 Lining material 68 Mounting location/type20 End termination material 69 Enclosure material21 Gnd/protective ring matl 7022 71 PERFORMANCE CHARACTERISTICS23 72 Min press at design temp At24 END EXTENSIONS 73 Max press at design temp25 End termination type Style 74 Min working temperature Max26 Bolting material 75 Accuracy rating27 End termination material 76 Min velocity URL Max28 Gasket/O ring material 77 Min liquid conductivity29 78 Output signal damping LRL URL30 SENSING ELEMENT 79 Min ambient working temp Max31 Electrode type 80 Contacts ac rating At max32 Insertion length 81 Contacts dc rating At max33 Electrode material 82 Max sensor to receiver lg34 8335 COILS AND HOUSING 8436 Housing construction type 8537 Coil conn arrangement 86 ACCESSORIES38 Enclosure type no/class 87 Connecting cables length39 Signal power source 88 Cable Glands40 Signal termination type 89 Ultrasonic cleaner style41 Cert/Approval type 90 Empty tube detector42 Housing material 91 Calibrator adaptor43 92 Calibrator/configurator44 9345 TRANSMITTER OR CONVERTER 94 SPECIAL REQUIREMENTS46 Housing type 95 Custom tag47 Output signal type 96 Reference specification48 Enclosure type no/class 97 Compliance standard49 Characteristic curve 98 Calibration report50 Digital communication std 99 Software configuration51 Signal power source 10052 Failsafe style 101 PHYSICAL DATA53 Integral indicator style 102 Estimated weight54 Signal termination type 103 Face-to-face dimension55 Cert/Approval type 104 Overall height56 Mounting location/type 105 Removal clearance57 Failure/Diagnostic action 106 Signal conn nominal size Style58 Enclosure material 107 Mfr reference dwg59 108

110 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT OR SCALE111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV ACTION LRV URV112 Flow rate-Analog output113 Flow rate-Digital output114 Flow rate-Freq output115 Flow rate-Scale116 Test pressure117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

1 RESPONSIBLE ORGANIZATION ULTRASONIC FLOWMETER 6 SPECIFICATION IDENTIFICATIONS2 w/wo SWITCHES 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 PRIMARY HEAD OR TUBE 56 TRANSMITTER OR TOTALIZER w/wo SWITCHES Continued 12 Primary head/Tube type 57 Cert/Approval type13 End conn nominal size Rating 58 Mounting location/type14 End conn termn type Style 59 Failure/Diagnostic action15 Transducer conn type 60 Calibration mode16 Head/Tube material 61 Data logger points17 Flange material 62 Measurement compensation18 Gasket/O ring material 63 Enclosure material19 6420 6521 TRANSDUCER 66 PERFORMANCE CHARACTERISTICS22 Measurement type 67 Max press at design temp At23 Beam/Sound track style 68 Min working temperature Max24 Nominal range size 69 Flow accuracy rating Ref25 Temperature LRL URL 70 Min flow/Velocity URL Max26 Mounting hardware 71 Minimum gas content Max27 Housing material 72 Minimum solids content Max28 73 Min ambient working temp Max29 74 Contacts ac rating At max30 CONNECTION HEAD 75 Contacts dc rating At max31 Housing type 76 Max sensor to receiver lg32 Enclosure type no/class 7733 Signal conn termn style 7834 Cert/Approval type 79 ACCESSORIES35 Enclosure material 80 Acoustic coupling matl36 81 Sound velocity sensor37 LEAD WIRE AND EXTENSION 82 Wall thickness sensor38 Extension type 83 Mounting kit39 Cable length 84 Tools40 Min cable operating temp Max 8541 Signal termination type 86 SPECIAL REQUIREMENTS42 Cable jacket material 87 Custom tag43 88 Reference specification44 TRANSMITTER OR TOTALIZER w/wo SWITCHES 89 Compliance standard45 Configuration type 90 Certificates46 Aux input signal type 91 Software configuration47 Output signal type 9248 Enclosure type no/class 93 PHYSICAL DATA 49 Local operator interface 94 Estimated weight50 Digital communication std 95 Face-to-face dimension51 Signal power source 96 Overall height52 Measurement type 97 Removal clearance53 Contacts arrangement Quantity 98 Signal conn nominal size Style54 Integral indicator style 99 Mfr reference dwg55 Signal termination type 100

110 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT OR SCALE111 TAG NO/FUNCTIONAL MEAS/SIGNAL/SCAL LRV URV ACTION LRV URV112 Meas-Analog output 1113 Meas-Analog output 2114 Meas-Analog output 3115 Meas-Analog output 4116 Meas-Scale 1117 Meas-Scale 2118 Meas setpoint 1-119 Meas setpoint 2-120 Meas setpoint 3-121 Meas setpoint 4-122 Failure signal-Output123124 COMPONENT IDENTIFICATIONS125 COMPONENT TYPE MANUFACTURER MODEL NUMBER126127128129Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS

Form: 20F2341 Rev 0 © 2004 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

1 RESPONSIBLE ORGANIZATION THERMAL MASS FLOWMETER 6 SPECIFICATION IDENTIFICATIONS2 w/wo SWITCHES 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 BODY OR FITTING 57 TRANSMITTER w/wo SWITCHES Continued 12 Body/Fitting type 58 Integral indicator style13 Process conn nominal size Rating 59 Readout variables14 Process conn termn type Style 60 Readout units15 Packing gland nom rating 61 Signal termination type16 Mounting orientation 62 Cert/Approval type17 Flow straightener type 63 Mounting location/type18 Body/Fitting material 64 Failure/Diagnostic action19 Flange material 65 Calibration mode20 Compression ferrule matl 66 Measurement compensation21 67 Enclosure material22 6823 SENSING ELEMENT 69 PERFORMANCE CHARACTERISTICS24 Sensor type 70 Max press at design temp At25 Temperature LRL URL 71 Min working temperature Max26 Minimum flow span Max 72 Flow rate accuracy27 Qty sensors per element 73 Temperature accuracy28 Extension/Support dia 74 Flow repeatability29 Max/Fixed insertion lg 75 Max flow response time30 Wetted material 76 Min ambient working temp Max31 Extension/Support matl 77 Contacts ac rating At max32 78 Contacts dc rating At max33 79 Max sensor to receiver lg34 LEAD WIRE AND EXTENSION 8035 Extension type 81 ACCESSORIES36 Cable length 82 Sensor cleaning system37 Max cable operating temp 83 Flow straightener38 Signal termination type 84 Enclosure heating kit39 Cable jacket material 85 Calibrator/Configurator40 8641 CONNECTION HEAD 87 SPECIAL REQUIREMENTS42 Housing type 88 Custom tag43 Enclosure type no/class 89 Reference specification44 Mounting location/type 90 Special preparation45 Enclosure material 91 Compliance standard46 92 Calibration report47 TRANSMITTER w/wo SWITCHES 93 Software configuration48 Housing type 9449 Aux input signal type 95 PHYSICAL DATA 50 Output signal type 96 Estimated weight51 Enclosure type no/class 97 Face-to-face dimension52 Local operator interface 98 Overall height53 Digital communication std 99 Removal clearance54 Signal power source 100 Signal conn nominal size Style55 Qty of input sensors 101 Mfr reference dwg56 Contacts arrangement Quantity 102

110 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT OR SCALE111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/SCALE LRV URV ACTION LRV URV112 Flow-Analog output 1113 Flow-Analog output 2114 Flow-Analog output 3115 Flow-Analog output 4116 Flow-Scale117 Temperature-Scale118 Temp-Analog output119 Flow-Digital output120 Flow setpoint 1-Output121 Flow setpoint 2-Output122123 COMPONENT IDENTIFICATIONS124 COMPONENT TYPE MANUFACTURER MODEL NUMBER125126127128


Form: 20F2351 Rev 0 © 2004 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

1 RESPONSIBLE ORGANIZATION THERMAL MASS FLOW SWITCH 6 SPECIFICATION IDENTIFICATIONS2 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 BODY OR FITTING 60 PERFORMANCE CHARACTERISTICS12 Body/Fitting type 61 Max press at design temp At13 Process conn nominal size Rating 62 Min working temperature Max14 Process conn termn type Style 63 Flow rate accuracy15 Packing gland nom rating 64 Temperature accuracy16 Mounting orientation 65 Flow repeatability17 Body/Fitting material 66 Max flow response time18 Flange material 67 Min ambient working temp Max19 Compression ferrule matl 68 Contacts ac rating At max20 69 Contacts dc rating At max21 70 Max sensor to receiver lg22 SENSING ELEMENT 7123 Sensor type 7224 Temperature LRL URL 7325 Flow Lower Range-Limit URL 7426 Heater power rating 7527 Max/Fixed insertion lg 7628 Wetted material 7729 7830 7931 LEAD WIRE AND EXTENSION 8032 Extension type 8133 Cable length 8234 Max cable operating temp 83 ACCESSORIES35 Signal termination type 84 Remote relay36 Cable jacket material 85 Flow straightener37 86 Enclosure heating kit38 CONNECTION HEAD 8739 Housing type 8840 Enclosure type no/class 8941 Mounting location/type 90 SPECIAL REQUIREMENTS42 Enclosure material 91 Custom tag43 92 Reference specification44 SWITCH MECHANISM 93 Special preparation45 Housing type 94 Compliance standard46 Output signal type 95 Calibration report47 Enclosure type no/class 9648 Signal power source 9749 Contacts arrangement Quantity 9850 Integral indicator style 99 PHYSICAL DATA 51 Signal termination type 100 Estimated weight52 Cert/Approval type 101 Face-to-face dimension53 Mounting location/type 102 Overall height54 Failure/Diagnostic action 103 Removal clearance55 Calibration mode 104 Signal conn nominal size Style56 Measurement compensation 105 Mfr reference dwg57 Enclosure material 10658 10759 108

110 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT OR SCALE111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/SCALE LRV URV ACTION LRV URV112 Flow setpoint 1-Output113 Flow setpoint 2-Output114 Temp setpoint-Output115 Temp-Analog output116 Flow-Analog output117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125


Form: 20F2361 Rev 0 © 2004 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

Form: 20F2381 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION VORTEX OR SWIRL FLOWMETER 6 SPECIFICATION IDENTIFICATIONS2 w/wo TOTALIZER INDICATOR 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 FLOWMETER BODY 58 TOTALIZER INDICATOR12 Body type 59 Totalizer type13 End conn nominal size Rating 60 Enclosure type no/class14 End conn termn type Style 61 Signal power source15 Seal type 62 Contacts arrangement Quantity16 Mounting hardware 63 Totalizer reset style17 Body wetted material 64 Integral indicator style18 End termination material 65 Cert/Approval type19 Gasket/Seal material 66 Mounting location/type20 67 Enclosure material21 6822 69 PERFORMANCE CHARACTERISTICS23 SENSING ELEMENT 70 Max press at design temp At24 Sensor type 71 Min working temperature Max25 Sensor wetted material 72 Flow rate accuracy rating26 Fill fluid material 73 Density accuracy rating27 74 Min velocity URL Max28 75 Density LRL URL29 76 Min reqd back press30 CONNECTION HEAD 77 Pressure drop at flow URL31 Housing type 78 Min ambient working temp Max32 Enclosure type no/class 79 Contacts ac rating At max33 Signal termination type 80 Contacts dc rating At max34 Cert/Approval type 81 Max sensor to receiver lg35 Enclosure material 8236 83 ACCESSORIES37 84 Connecting cables length38 TRANSMITTER OR COMPUTER 85 Isolation manifold39 Housing type 86 Remote indicator style40 Measurement compensation 87 Calibrator adapter41 Output signal type 8842 Enclosure type no/class 89 SPECIAL REQUIREMENTS43 Span-zero adjustment 90 Custom tag44 Characteristic curve 91 Reference specification45 Digital communication std 92 Special preparation46 Signal power source 93 Compliance standard47 Failsafe style 94 Calibration report48 Integral indicator style 95 Software configuration49 Signal termination type 9650 Cert/Approval type 97 PHYSICAL DATA51 Mounting location/type 98 Estimated weight52 Calibration type 99 Face-to-face dimension53 Failure/Diagnostic action 100 Overall height54 Enclosure material 101 Removal clearance55 102 Signal conn nominal size Style56 103 Mfr reference dwg57 104

110 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT OR SCALE111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV ACTION LRV URV112 Flow rate-Analog output113 Mass flow-Analog output114 Meas-Analog output115 Meas-Freq output 1116 Meas-Freq output 2117 Measurement-Scale118 Temp-Digital output119 Meas-Digital output120 Density-Digital output121 Test pressure122 COMPONENT IDENTIFICATIONS123 COMPONENT TYPE MANUFACTURER MODEL NUMBER124125126127Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

1 RESPONSIBLE ORGANIZATION SONAR FLOWMETER 6 SPECIFICATION IDENTIFICATIONS 2 w/wo ENTRAINED GAS MONITOR 7 Document no 3 Device Specification 8 Latest revision Date 4 9 Issue status 5 10

11 SENSOR HEAD COVER 56 TRANSMITTER OR TOTALIZER w/wo SWITCHES Continued 12 Head/Tube cover type 57 Data logger points 13 Cover style 58 Measurement compensation 14 Pipe/Tube nominal size 59 Enclosure material 15 Head cover material 60 16 Gasket/Seal material 61 17 62 18 63 PERFORMANCE CHARACTERISTICS19 SENSING ELEMENT 64 Min working temperature Max20 Measurement type 65 Flow accuracy rating Ref21 Sensor style 66 Entrained Air/gas accuracy Ref22 Band type 67 Flow repeatability Ref23 Band material 68 Min flow/velocity URL Max24 69 Entrained Air/gas LRL URL25 70 Update rate 26 CONNECTION HEAD OR PREAMPLIFIER 71 Min ambient working temp Max27 Configuration type 72 Contacts dc rating At max28 Output signal type 73 Max sensor to receiver lg29 Enclosure type no/class 74 30 Signal conn termn style 75 31 Cert/Approval type 76 32 77 ACCESSORIES 33 LEAD WIRE AND EXTENSION 78 Mounting hardware 34 Extension type 79 Thermal blanket35 Cable length 80 36 Min cable operating temp Max 81 37 Signal termination type 82 38 Cert/Approval type 83 SPECIAL REQUIREMENTS39 Cable jacket material 84 Custom tag40 85 Reference specification 41 TRANSMITTER OR TOTALIZER w/wo SWITCHES 86 Calibration report 42 Configuration type 87 Software configuration 43 Aux input signal type 88 44 Output signal type 89 45 Enclosure type no/class 90 46 Local operator interface 91 PHYSICAL DATA 47 Digital communication std 92 Estimated weight 48 Signal power source 93 Overall length 49 Contacts arrangement Quantity 94 Removal clearance 50 Integral indicator style 95 Outside diameter 51 Signal termination type 96 Signal conn nominal size Style52 Cert/Approval type 97 Mfr reference dwg53 Mounting location/type 9854 Failure/Diagnostic action 9955 Memory interface 100

110 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT OR SCALE 111 TAG NO/FUNCTIONAL MEAS/SIGNAL/SCAL LRV URV ACTION LRV URV112 Flow-Analog output 1 113 Total flow-Output 2 114 -Freq output115 -Digital output 116 Flow-Scale 1 117 Total flow-Scale 2 118 Flow setpoint-Output 119 Failure signal-Output 120 121122123124 COMPONENT IDENTIFICATIONS 125 COMPONENT TYPE MANUFACTURER MODEL NUMBER 126 127 128 129 Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS

Form: 20F2391 Rev 0 © 2007 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

1 RESPONSIBLE ORGANIZATION POSITIVE DISPLACEMENT FLOWMETER 6 SPECIFICATION IDENTIFICATIONS 2 DIRECT-READING TYPE 7 Document no 3 Device Specification 8 Latest revision Date4 9 Issue status 5 10

11 OPERATING PARAMETERS 64 DRIVE TRAIN AND ADJUSTER 12 Project number Sub project no 65 Drive type 13 Project 66 Accuracy adjuster type 14 Enterprise 67 Temp compensation type 15 Site 68 16 Area Cell Unit 69 17 Related equipment 70 REGISTER OR TOTALIZER18 71 Register/Totalizer type 19

Service 72 Enclosure type no/class

20 P&ID/Reference dwg number 73 Signal power source 21 Upstr line/nozzle number 74 Totalizer reset style 22 Upstream line pipe spec 75 Integral indicator style 23 Upstr line nominal size Rating 76 Cert/Approval type 24 Upstr line conn type Style 77 Mounting location/type 25 Upstr line material type 78 Enclosure material 26 Inline hazardous area cl Div/Zone Group 79 27 Inline area min ign temp Temp ident number 8028 Minimum inlet pressure 81 PERFORMANCE CHARACTERISTICS29 Maximum inlet pressure 82 Max press at design temp At30 Minimum temperature 83 Min working temperature Max31 Maximum temperature 84 Max viscosity limit32 Min liquid std flow rate 85 Accuracy rating Ref33 Max liquid std flow rate 86 Repeatability Ref34 Minimum liquid viscosity 87 Flow rate LRL URL35 Maximum liquid viscosity 88 Recommended filter size 36 Max pressure differential 89 Pressure drop at URL 37 Material name 90 Min ambient working temp Max38 Matl density at ref temp At 91 Max sensor to receiver lg 39 NFPA health hazard Flammability Reactivity 9240 9341 94 ACCESSORIES 42 95 Strainer43 FLOWMETER BODY 96 Air/Vapor eliminator44 Body/Housing type 9745 Inlet conn nominal size Rating 9846 Outlet conn nominal size Rating 99 SPECIAL REQUIREMENTS47 End conn termn type Style 100 Custom tag48 Flow direction/Mounting 101 Reference specification 49 Body/Housing material 102 Compliance standard 50 Cap/End cover material 103 Calibration report 51 Seal/O ring material 104 Material certificate 52 105 Service design 53 10654 MEASURING CHAMBER 10755 Displacement element type 108 PHYSICAL DATA 56 Construction style 109 Estimated weight 57 Nominal meter size 110 Face-to-face dimension 58 Sensor style 111 Overall height 59 Displacement element matl 112 Removal clearance 60 Measuring chamber matl 113 Signal conn nominal size Style61 Bearing/Bushing matl 114 Mfr reference dwg62 Shaft material 11563 116

117 CALIBRATIONS AND TEST INPUT OR TEST SCALE118 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV LRV URV FACTOR119 Volume-Accum total scale 120 Volume-Totalized scale 121 Flow rate-Scale 122 123 COMPONENT IDENTIFICATIONS 124 COMPONENT TYPE MANUFACTURER MODEL NUMBER 125 126 127 128 Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS

Form: 20F2411 Rev 0 © 2005 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

1 RESPONSIBLE ORGANIZATION POSITIVE DISPLACEMENT FLOWMETER 6 SPECIFICATION IDENTIFICATIONS 2 w TRANSMITTER OR ACCESSORIES 7 Document no 3 Device Specification 8 Latest revision Date 4 9 Issue status 5 10

11 FLOWMETER BODY 58 PERFORMANCE CHARACTERISTICS 12 Body/Housing type 59 Max press at design temp At13 Inlet conn nominal size Rating 60 Min working temperature Max14 Outlet conn nominal size Rating 61 Max viscosity limit 15 End conn termn type Style 62 Accuracy rating Ref16 Flow direction/Mounting 63 Repeatability Ref17 Body/Housing material 64 Flow rate LRL URL18 Cap/End cover material 65 Meter mean K-factor19 Seal/O ring material 66 Recommended filter size 20 67 Pressure drop at URL 21 68 Min ambient working temp Max22 MEASURING CHAMBER 69 Contact ac rating At max23 Displacement element type 70 Contact dc rating At max24 Construction style 71 Max sensor to receiver lg25 Nominal meter size 7226 Sensor style 7327 Displacement element matl 7428 Measuring chamber matl 75 ACCESSORIES 29 Bearing/Bushing matl 76 Strainer30 Shaft material 77 Strainer mesh size 31 78 Valve style 32 79 Lubrication system 33 DRIVE TRAIN AND ADJUSTER 80 Air/Vapor eliminator34 Drive type 81 End connection adapter35 Accuracy adjuster type 8236 Temp compensation type 8337 8438 85 SPECIAL REQUIREMENTS39 TRANSMITTER OR TOTALIZER w/wo SWITCHES 86 Custom tag40 Configuration type 87 Reference specification 41 Aux input signal type 88 Compliance standard 42 Output signal type 89 Calibration report 43 Enclosure type no/class 90 Material certificate 44 Control mode 91 Service design 45 Digital communication std 9246 Signal power source 9347 Totalizer reset style 9448 Contacts arrangement Quantity 95 PHYSICAL DATA 49 Pulse per revolution 96 Estimated weight 50 Integral indicator style 97 Face-to-face dimension 51 Signal termination type 98 Overall height52 Cert/Approval type 99 Removal clearance 53 Mounting location/type 100 Signal conn nominal size Style54 Integral printer style 101 Mfr reference dwg55 Enclosure material 10256 10357 104110 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT OR SCALE 111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/SCALE LRV URV ACTION LRV URV112 Meas-Analog output 1 113 Meas-Analog output 2114 Volume-Accum total scale115 Volume-Totalized scale116 Flow rate-Scale 117 Meas setpoint 1-Output 118 Meas setpoint 2-Output 119 Failure signal-Output120 121 COMPONENT IDENTIFICATIONS 122 COMPONENT TYPE MANUFACTURER MODEL NUMBER 123 124 125 126 127 Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS

Form: 20F2421 Rev 0 © 2005 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

Form 20F2521 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION CORIOLIS MASS FLOWMETER 6 SPECIFICATION IDENTIFICATIONS2 w/wo TOTALIZER INDICATOR 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 FLOWMETER BODY AND HOUSING 58 TOTALIZER INDICATOR12 Body/Housing type 59 Totalizer type13 End conn nominal size Rating 60 Enclosure type no/class14 End conn termn type Style 61 Signal power source15 Body wetted material 62 Contacts arrangement Quantity16 Housing material 63 Totalizer reset style17 End termination material 64 Integral indicator style18 65 Cert/Approval type19 66 Mounting location/type20 67 Enclosure material21 FLOWTUBE ASSEMBLY 6822 Flowtube type 69 PERFORMANCE CHARACTERISTICS23 Flowtube diameter 70 Max press at design temp At24 Flowtube material 71 Min working temperature Max25 72 Flow rate accuracy rating26 73 Density accuracy rating27 74 Min flow URL Max28 CONNECTION HEAD 75 Density LRL URL29 Housing type 76 Sec enclosure press rating30 Enclosure type no/class 77 Pressure drop at flow URL31 Signal termination type 78 Min ambient working temp Max32 Cert/Approval type 79 Contacts ac rating At max33 Housing material 80 Contacts dc rating At max34 81 Max sensor to receiver lg35 8236 83 ACCESSORIES37 TRANSMITTER OR COMPUTER 84 Connecting cables length38 Housing type 85 Heating kit style39 Measurement compensation 86 Calibrator/configurator40 Output signal type 8741 Enclosure type no/class 8842 Span-zero adjustment 89 SPECIAL REQUIREMENTS43 Characteristic curve 90 Custom tag44 Digital communication std 91 Reference specification45 Signal power source 92 Special preparation46 Failsafe style 93 Compliance standard47 Integral indicator style 94 Calibration report48 Signal termination type 95 Software configuration49 Cert/Approval type 9650 Mounting location/type 97 PHYSICAL DATA51 Failure/Diagnostic action 98 Estimated weight52 Enclosure material 99 Face-to-face dimension53 100 Overall height54 101 Removal clearance55 102 Signal conn nominal size Style56 103 Mfr reference dwg57 104

110 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT OR SCALE111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV ACTION LRV URV112 Mass flow-Analog output113 Meas-Analog output 2114 Meas-Analog output 3115 Meas-Freq output 1116 Meas-Freq output 2117 Measurement–Scale118 Temp-Digital output119 Meas-Digital output120 Density-Digital output121 Test pressure122 COMPONENT IDENTIFICATIONS123 COMPONENT TYPE MANUFACTURER MODEL NUMBER124125126127Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

1 RESPONSIBLE ORGANIZATION SIGHT FLOW INDICATOR 6 SPECIFICATION IDENTIFICATIONS2 w/wo ILLUMINATOR 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 OPERATING PARAMETERS 62 GAUGE ILLUMINATOR12 Project number Sub project no 63 Illumination type13 Project 64 Enclosure type no/class14 Enterprise 65 Power source15 Site 66 Cert/Approval type16 Area Cell Unit 67 Enclosure material17 Related equipment 6818 Service 6919 70 PERFORMANCE CHARACTERISTICS20 P&ID/Reference dwg 71 Max press at design temp At21 Upstr line/nozzle number 72 Min working temperature Max22 Upstream line pipe spec 73 Min flow for indication23 Upstr conn nominal size Rating 7424 Upstr line conn type Style 7525 Upstr conn orientation 7626 Upstr line material type 7727 Inline hazardous area cl Div/Zone Group 7828 Inline area min ign temp Temp ident number 7929 Minimum pressure 8030 Maximum pressure 8131 Minimum temperature 8232 Maximum temperature 8333 Material phase 8434 Material name 8535 Material color 8636 NFPA health hazard Flammability Reactivity 8737 8838 8939 9040 SIGHT FLOW INDICATOR 9141 Body type 9242 Window style 93 SPECIAL REQUIREMENTS43 End conn nominal size Rating 94 Custom tag44 End conn termn type Style 95 Reference specification45 End-to-end length std 96 Compliance standard46 Indicator type 97 Construction code47 Cover/Retainer style 98 Cert/Approval type48 Extended overall length 99 Service design49 Flow direction style 10050 Body/End fitting matl 10151 Lens/Cylinder material 10252 Lining material 103 PHYSICAL DATA 53 Bolting material 104 Estimated weight54 Cover/Retainer material 105 Overall length55 Shield/Protective matl 106 Overall height56 Flange/End conn material 107 Overall width57 Gasket/Seal/Packing matl 108 Sight opening diameter58 Lens cushion material 109 Mfr reference dwg59 Indicator material 11060 11161 112

113 CALIBRATIONS AND TEST TEST114 TAG NUMBER TEST URV115 Test pressure116117118119 COMPONENT IDENTIFICATIONS120 COMPONENT TYPE MANUFACTURER MODEL NUMBER121122123124125126Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS

Form: 20F2611 Rev 0 © 2004 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

Form: 20L2101 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION CAPACITANCE OR RF ADMITTANCE 6 SPECIFICATION IDENTIFICATIONS2 LEVEL TRANSMITTER w/wo SWITCHES 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 PROCESS CONNECTION 60 TRANSMITTER w/wo SWITCHES continued12 Body/Fitting type 61 Switch time delay13 Process conn nominal size Rating 62 Enclosure material14 Process conn termn type Style 6315 Wetted material 6416 Flange material 6517 Seal/O ring material 66 PERFORMANCE CHARACTERISTICS18 67 Max press at design temp At19 68 Min working temperature Max20 SENSING ELEMENT 69 Max discharge to sensor21 Configuration type 70 Accuracy rating22 Probe diameter 71 Min measurement span Max23 Insertion length 72 Min ambient working temp Max24 Inactive length 73 Contacts ac rating At max25 Integral cable length 74 Contacts dc rating At max26 Probe material 75 Max sensor to receiver lg27 Insulation/Sheath matl 7628 Weight material 7729 7830 7931 CONNECTION HEAD OR PREAMPLIFIER 8032 Type 8133 Measurement compensation 8234 Input signal URL 8335 Output signal type 84 ACCESSORIES36 Enclosure type no/class 85 Connecting cables length37 Power source 86 Power supply38 Cert/Approval type 87 Local indicator style39 Mounting location/type 88 Intrinsic safety barrier40 Enclosure material 8941 9042 9143 TRANSMITTER w/wo SWITCHES 92 SPECIAL REQUIREMENTS44 Housing type 93 Custom tag45 Measurement compensation 94 Reference specification46 Output signal type 95 Compliance standard47 Input signal URL 96 Calibration report48 Enclosure type no/class 9749 Characteristic curve 9850 Signal power source 9951 Contact arrangement Quantity 100 PHYSICAL DATA52 Failsafe style 101 Estimated weight53 RFI protection 102 Overall height54 Integral indicator style 103 Removal clearance55 Cert/Approval type 104 Signal conn nominal size Style56 Mounting location/type 105 Mfr reference dwg57 Static discharge prot 10658 Failure/Diagnostic action 10759 Adjustable signal damping 108

110 CALIBRATIONS AND TEST INPUT OR SETPOINT OUTPUT OR SCALE111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV ACTION LRV URV112 Level-Analog output113 Level-Scale114 Level setpoint 1-Output115 Level setpoint 2-Output116 Level setpoint 3-Output117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

Form: 20L2111 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION DIFFERENTIAL PRESSURE LEVEL 6 SPECIFICATION IDENTIFICATIONS2 TRANSMITTER - FLANGE MOUNTED 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 TRANSMITTER BODY 60 REMOTE SEAL12 Body/Flange type 61 Seal type13 Process conn nominal size Rating 62 Process conn nominal size Rating14 Process conn termn type Style 63 Process conn termn type Style15 Vent/Drain location 64 Diaphragm extension lg16 Mounting type 65 Instrument conn nom size17 Body/Flange material 66 Flushing conn quantity18 Vent/Drain material 67 Capillary/Fitting dia Length19 Bolting material 68 Diaphragm material20 Flange adapter material 69 Capillary-armor material21 Gasket/O ring material 70 Bolting material22 Mounting kit material 71 Upper housing material23 72 Lower housing/Flange matl24 73 Gasket/Oring material25 74 Fill fluid material26 SENSING ELEMENT 7527 Detector type 76 PERFORMANCE CHARACTERISTICS28 Min diff pressure span Max 77 Max press at design temp At29 Diaphragm/Wetted material 78 Min working temp Max30 Fill fluid material 79 Accuracy rating31 80 Diff pressure LRL URL32 81 Fill fluid sp gr At temp33 82 Ambient temperature error34 TRANSMITTER 83 Min ambient working temp Max35 Output signal type 8436 Enclosure type no/class 8537 Characteristic curve 8638 Digital communication std 87 ACCESSORIES39 Signal power source 88 Air set filter style40 Transient protection 89 Air set gauges41 Integral indicator style 90 Heating kit style42 Signal termination type 91 Remote indicator style43 Cert/Approval type 9244 Span-Zero adjust loc 9345 Failure/Diagnostic action 94 SPECIAL REQUIREMENTS46 Enclosure material 95 Custom tag47 96 Reference specification48 97 Special preparation49 98 Compliance standard50 INTEGRAL SEAL 99 Software configuration51 Seal type 10052 Process conn nominal size Rating 101 PHYSICAL DATA53 Process conn termn type Style 102 Estimated weight54 Diaphragm extension lg 103 Overall height55 Diaphragm material 104 Removal clearance56 Upper housing/Flange matl 105 Signal conn nominal size Style57 106 Mfr reference dwg58 10759 108

110 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT OR SCALE111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV ACTION LRV URV112 Diff press-Analog output113 Diff press-Scale114 Diff press-Digital output115 Press-Digital output116 Temp-Digital output117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125




--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

Form: 20L2121 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION 6 SPECIFICATION IDENTIFICATIONS2 DISPLACER-TYPE LEVEL TRANSMITTER 7 Document no3 OR LOCAL CONTROLLER 8 Latest revision Date

4 Device Specification 9 Issue status5 10

11 BODY OR CAGE 60 TRANSMITTER OR CONTROLLER continued12 Body/Cage type 61 Cert/Approval type13 Process conn nominal size Rating 62 Mounting location/type14 Process conn termn type Style 63 Span-Zero adjust lct15 Flange facing finish 64 Enclosure material16 Lower conn location Upper 6517 Gage glass conn nom size Rating 6618 Gage glass conn type Style 6719 Vent/Drain conn nom size Rating 68 PERFORMANCE CHARACTERISTICS20 Vent/Drain termn type Style 69 Max press at design temp At21 Head orientation/type 70 Min working temperature Max22 Extension/Heat insulator 71 Accuracy rating23 Body/Cage material 72 Level Lower Range-Limit URL24 Bolting material 73 Min level span Max25 Gasket/O ring material 74 Min differential sp gr26 75 Min ambient working temp Max27 76 Contacts ac rating At max28 77 Contacts dc rating At max29 SENSING ELEMENT 7830 Sensor type 7931 Sp gr Lower Range-Limit URL 8032 Displacer diameter Length 81 ACCESSORIES33 Extension length 82 Connecting cables length34 Displacer material 83 Air set filter style35 Torque tube/Spring matl 84 Air set gauges36 Extension/Cable material 85 Gage glass style37 Trim material 86 Gage valve style38 8739 8840 CONNECTION HEAD 89 SPECIAL REQUIREMENTS41 Type 90 Custom tag42 Enclosure type no/class 91 Reference specification43 Signal termination type 92 Special preparation44 Cert/Approval type 93 Compliance standard45 Enclosure material 94 Construction code46 95 Software configuration47 9648 9749 TRANSMITTER OR CONTROLLER w/wo SWITCHES 98 PHYSICAL DATA50 Housing type 99 Estimated weight51 Output signal type 100 Overall height52 Enclosure type no/class 101 Removal clearance53 Control mode 102 Upper to lower conn lg54 Digital communication std 103 Lower to drain conn lg55 Signal power source 104 Signal conn nominal size Style56 Contacts arrangement Quantity 105 Mfr reference dwg57 Transient protection 10658 Integral indicator style 10759 Signal termination type 108

110 CALIBRATIONS AND TEST INPUT OR SETPOINT OUTPUT OR SCALE111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV ACTION LRV URV112 Level-Analog output113 Level-Digital output114 Level-Scale115 Level setpoint 1-Output116 Level setpoint 2-Output117 Test pressure118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125




--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

Form: 20L2141 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION NUCLEAR RADIATION LEVEL 6 SPECIFICATION IDENTIFICATIONS2 TRANSMITTER w/wo SWITCHES 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 RADIATION SOURCE 60 PERFORMANCE CHARACTERISTICS12 Source type 61 Level accuracy rating13 Number of sources 62 Density accuracy rating14 Source size 63 Min measurement span Max15 Fireproof design type 64 Response time16 Shutter style 65 Min ambient working temp Max17 Position switch type 66 Contacts ac rating At Max18 Mounting location/type 67 Contacts dc rating At Max19 Collimation angle 68 Max sensor to receiver lg20 Source material 6921 Housing material 7022 7123 7224 SENSING ELEMENT 7325 Detector type 7426 Detector style 7527 Number of detectors 7628 Active length 7729 7830 7931 CONNECTION HEAD OR PREAMPLIFIER 8032 Type 8133 Housing type 8234 Measurement compensation 8335 Output signal type 8436 Enclosure type no/class 85 ACCESSORIES37 Signal power source 86 Connecting cables length38 Cert/Approval type 87 Mounting hardware39 Mounting location/type 88 Calibrator40 Enclosure material 8941 9042 9143 TRANSMITTER w/wo SWITCHES 9244 Housing type 93 SPECIAL REQUIREMENTS45 Measurement compensation 94 Custom tag46 Output signal type 95 Reference specification47 Enclosure type no/class 96 Compliance standard48 Characteristic curve 9749 Digital communication std 9850 Signal power source 9951 Contact arrangement Quantity 100 PHYSICAL DATA52 Failsafe style 101 Estimated weight53 Integral indicator style 102 Overall length54 Cert/Approval type 103 Removal clearance55 Mounting location/type 104 Signal conn nominal size Style56 Failure/Diagnostic action 105 Mfr reference dwg57 Enclosure material 10658 10759 108

110 CALIBRATIONS AND TEST INPUT OR SETPOINT OUTPUT OR SCALE111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV ACTION LRV URV112 Level-Analog output113 Level-Digital output114 Level-Scale115 Density-Digital output116 Level setpoint 1-Output117 Level setpoint 2-Output118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

Form: 20L2151 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION RESISTANCE-TAPE LEVEL 6 SPECIFICATION IDENTIFICATIONS2 TRANSMITTER w/wo SWITCHES 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 PROCESS CONNECTION 60 PERFORMANCE CHARACTERISTICS12 Body/Fitting type 61 Max press at design temp At13 Process conn nominal size Rating 62 Min working temperature Max14 Process conn termn type Style 63 Repeatability15 Shell/cap material 64 Min measurement span Max16 Seal/O ring material 65 Sensor resistance coef17 66 Actuation depth18 67 Min ambient working temp Max19 68 Contacts ac rating At max20 SENSING ELEMENT 69 Contacts dc rating At max21 Detector type 70 Max sensor to receiver lg22 Temperature sensor qty 7123 Temperature coefficient 7224 Temp nominal resistance At 7325 Sheath style 7426 Overall length 7527 Inactive length 7628 Sheath material 7729 Protector material 7830 7931 8032 8133 CONNECTION HEAD OR HOUSING 8234 Type 8335 Housing style 8436 Enclosure type no/class 85 ACCESSORIES37 Signal termination type 86 Connecting cables length38 Cert/Approval type 87 Local indicator style39 Mounting location/type 88 Intrinsic safety barrier40 Enclosure material 8941 Breather material 9042 Fitting material 9143 9244 93 SPECIAL REQUIREMENTS45 TRANSMITTER w/wo SWITCHES 94 Custom tag46 Housing type 95 Reference specification47 Output signal type 96 Compliance standard48 Enclosure type no/class 9749 Characteristic curve 9850 Signal power source 9951 Contacts arrangement Quantity 100 PHYSICAL DATA52 Failsafe style 101 Estimated weight53 Integral indicator style 102 Overall height54 Cert/Approval type 103 Removal clearance55 Mounting location/type 104 Signal conn nominal size Style56 Enclosure material 105 Mfr reference dwg57 10658 10759 108

110 CALIBRATIONS AND TEST INPUT OR SETPOINT OUTPUT OR SCALE111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV ACTION LRV URV112 Level-Analog output113 Temp-Analog output114 Level-Scale115 Level setpoint 1-Output116 Level setpoint 2-Output117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

Form: 20L2171 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION NON-CONTACT ULTRASONIC LEVEL 6 SPECIFICATION IDENTIFICATIONS2 TRANSMITTER w/wo SWITCHES 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 PROCESS CONNECTION 60 PERFORMANCE CHARACTERISTICS12 Body/Fitting type 61 Max press at design temp At13 Process conn nominal size Rating 62 Min working temperature Max14 Process conn termn type Style 63 Accuracy rating15 Wetted material 64 Level lower range limit URL16 Flange material 65 Min measurement span Max17 Seal/O ring material 66 Beam angle18 67 Min ambient working temp Max19 68 Contacts ac rating At max20 69 Contacts dc rating At max21 SENSING ELEMENT 70 Max sensor to receiver lg22 Detector type 7123 Detector style 7224 Insertion length 7325 Integral cable length 7426 7527 7628 7729 CONNECTION HEAD 7830 Type 7931 Enclosure type no/class 8032 Cert/Approval type 8133 Mounting location/type 8234 Enclosure material 8335 84 ACCESSORIES36 85 Connecting cables length37 86 Enclosure heater38 TRANSMITTER w/wo SWITCHES 87 Mounting hardware39 Housing type 8840 Measurement compensation 8941 Output signal type 9042 Enclosure type no/class 9143 Control sequence 92 SPECIAL REQUIREMENTS44 Characteristic curve 93 Custom tag45 Digital communication std 94 Reference specification46 Signal power source 95 Compliance standard47 Contact arrangement Quantity 96 Calibration report48 Failsafe style 9749 Integral indicator style 9850 Cert/Approval type 9951 Mounting location/type 100 PHYSICAL DATA52 Failure/Diagnostic action 101 Estimated weight53 Signal processing 102 Overall height54 Enclosure material 103 Removal clearance55 104 Signal conn nominal size Style56 105 Mfr reference dwg57 10658 10759 108

110 CALIBRATIONS AND TEST INPUT OR SETPOINT OUTPUT OR SCALE111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV ACTION LRV URV112 Level–Analog output113 Level-Scale114 Level setpoint 1-Output115 Level setpoint 2-Output116 Level setpoint 3-Output117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

Form: 20L2301 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION CAPACITANCE OR RF ADMITTANCE 6 SPECIFICATION IDENTIFICATIONS2 LEVEL SWITCH 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 PROCESS CONNECTION 60 SWITCH MECHANISM continued12 Body/Fitting type 61 RFI protection13 Process conn nominal size Rating 62 Switch time delay14 Process conn termn type Style 63 Enclosure material15 Wetted material 6416 Flange material 6517 Seal/O ring material 66 PERFORMANCE CHARACTERISTICS18 67 Max press at design temp At19 68 Min working temperature Max20 SENSING ELEMENT 69 Max discharge to sensor21 Configuration type 70 Repeatability/Sensitivity22 Number of elements 71 Min measurement span Max23 Probe diameter 72 Min ambient working temp Max24 Insertion length 73 Contacts ac rating At max25 Inactive/Dead length 74 Contacts dc rating At max26 Integral cable length 75 Max sensor to receiver lg27 Probe material 7628 Insulation/Sheath matl 7729 Weight material 7830 7931 8032 CONNECTION HEAD OR PREAMPLIFIER 8133 Type 8234 Measurement compensation 8335 Input signal URL 8436 Output signal type 85 ACCESSORIES37 Enclosure type no/class 86 Connecting cables length38 Signal power source 87 Mounting hardware39 Cert/Approval type 88 External relay40 Mounting location/type 89 Intrinsic safety barrier41 Enclosure material 9042 9143 9244 SWITCH MECHANISM 93 SPECIAL REQUIREMENTS45 Housing type 94 Custom tag46 Element style 95 Reference specification47 Measurement compensation 96 Compliance standard48 Output signal type 9749 Input signal LRL URL 9850 Enclosure type no/class 9951 Signal power source 100 PHYSICAL DATA52 Dead band type 101 Estimated weight53 Contacts arrangement Quantity 102 Overall height54 Failsafe style 103 Removal clearance55 Integral indicator style 104 Signal conn nominal size Style56 Cert/Approval type 105 Mfr reference dwg57 Mounting location/type 10658 Static discharge prot 10759 Failure/Diagnostic action 108

110 CALIBRATIONS AND TEST SETPOINT OUTPUT111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV ACTION LRV URV112 Level setpoint 1-Output113 Level setpoint 2-Output114 Level setpoint 3-Output115 Level setpoint 4-Output116117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

Form: 20L2311 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION FLOAT OR DISPLACER LEVEL SWITCH 6 SPECIFICATION IDENTIFICATIONS2 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 BODY OR CAGE 60 PERFORMANCE CHARACTERISTICS12 Body/Cage type 61 Max press at design temp At13 Process conn nominal size Rating 62 Min working temperature Max14 Process conn termn type Style 63 Repeatability15 Flange facing finish 64 Level Lower Range-Limit URL16 Lower conn location Upper 65 Dead band rating17 Gage glass conn nom size Style 66 Min ambient working temp Max18 Try-cock conn nom size Style 67 Contacts ac rating At max19 Head orientation/type 68 Contacts dc rating At max20 Extension/Heat insulator 6921 Body/Cage material 7022 Bolting material 7123 Gasket material 7224 7325 7426 7527 SENSING ELEMENT 7628 Sensor type 7729 Sp gr Lower Range-Limit URL 7830 Adjustable LRL URL 7931 Sensor quantity 8032 Float/Displacer dia Length 8133 Extension/stem length 82 ACCESSORIES34 Float/Displacer material 83 Try-cocks style35 Torque tube/Spring matl 84 Gage glass style36 Magnetic sleeve material 85 Gage valve style37 Extension/Cable material 86 Mechanical test mechanism38 Trim material 8739 8840 89 SPECIAL REQUIREMENTS41 90 Custom tag42 SWITCH MECHANISM 91 Reference specification43 Housing type 92 Special preparation44 Element style 93 Compliance standard45 Output signal type 94 Construction code46 Enclosure type no/class 9547 Control sequence 9648 Signal power source 9749 Contacts arrangement Quantity 98 PHYSICAL DATA50 Signal termination type 99 Estimated weight51 Cert/Approval type 100 Overall height52 Dead band type 101 Removal clearance53 Enclosure material 102 Upper to lower conn lg54 Exterior coating material 103 Lower to drain conn lg55 104 Signal conn nominal size Style56 105 Mfr reference dwg57 10658 10759 108




--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

Form: 20L2312 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION TANK LEVEL GAUGE OR INDICATOR 6 SPECIFICATION IDENTIFICATIONS2 w/wo SWITCHES 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 PROCESS CONNECTION 60 SWITCH MECHANISM continued12 Body/Fitting type 61 Mounting location/type13 Process conn nominal size Rating 62 Enclosure material14 Process conn termn type Style 6315 Wetted material 6416 6517 66 PERFORMANCE CHARACTERISTICS18 SENSING ELEMENT 67 Max press at design temp At19 Sensor type 68 Min working temperature Max20 Nominal size 69 Min specific gravity Max21 Sensor material 70 Indication accuracy22 Guide cable material 71 Switch repeatability23 Bottom anchor material 72 Min differential sp gr24 Top anchor material 73 Min ambient working temp Max25 74 Contacts ac rating At max26 75 Contacts dc rating At max27 7628 TAPE CONDUIT 7729 Sheave elbow type 7830 Liquid seal style 7931 Tape material 8032 Sheave elbow material 8133 Pipe material 8234 Liquid seal sheave matl 8335 Tape wipe material 8436 Conduit vent fitting matl 8537 86 ACCESSORIES38 87 Calibrator39 GAUGE OR INDICATOR 88 Condensate reservoir40 Type 89 Shock absorber41 Spring Motor style 90 Isolation valve42 Level URL 9143 Seal type 9244 Graduations and color 93 SPECIAL REQUIREMENTS45 Mounting location/type 94 Custom tag46 Sensor check style 95 Reference specification47 Housing material 96 Compliance standard48 9749 9850 SWITCH MECHANISM 9951 Housing type 100 PHYSICAL DATA52 Output signal type 101 Estimated weight53 Max level span 102 Overall height54 Enclosure type no/class 103 Removal clearance55 Signal power source 104 Signal conn nominal size Style56 Contact arrangement Quantity 105 Mfr reference dwg57 Failsafe style 10658 Integral indicator style 10759 Cert/Approval type 108

110 CALIBRATIONS AND TEST INPUT OR SETPOINT OUTPUT OR SCALE111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV ACTION LRV URV112 Level-Scale113 Level setpoint 1-Output114 Level setpoint 2-Output115 Level setpoint 3-Output116 Level setpoint 4-Output117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

Form: 20L2321 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION NUCLEAR RADIATION LEVEL SWITCH 6 SPECIFICATION IDENTIFICATIONS2 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 RADIATION SOURCE 60 PERFORMANCE CHARACTERISTICS12 Shutter type 61 Repeatability/Sensitivity13 Number of sources 62 Response time14 Source size 63 Min ambient working temp Max15 Fireproof design type 64 Contacts ac rating At max16 Position switch type 65 Contacts dc rating At max17 Mounting location/type 66 Max sensor to receiver lg18 Source material 6719 Housing material 6820 6921 7022 7123 SENSING ELEMENT 7224 Detector type 7325 Number of detectors 7426 Active length 7527 Check source actuation 7628 7729 7830 7931 CONNECTION HEAD OR PREAMPLIFIER 8032 Type 8133 Housing type 8234 Output signal type 8335 Enclosure type no/class 8436 Signal power source 8537 Cert/approval type 86 ACCESSORIES38 Mounting location/type 87 Connecting cables length39 Enclosure material 88 Mounting hardware40 8941 9042 9143 SWITCH MECHANISM 9244 Housing type 93 SPECIAL REQUIREMENTS45 Output signal type 94 Custom tag46 Enclosure type no/class 95 Reference specification47 Signal power source 96 Compliance standard48 Contacts arrangement Quantity 9749 Failsafe style 9850 Integral indicator style 9951 Cert/Approval type 100 PHYSICAL DATA52 Mounting location/type 101 Estimated weight53 Failure/Diagnostics action 102 Overall length54 Enclosure material 103 Removal clearance55 104 Signal conn nominal size Style56 105 Mfr reference dwg57 10658 10759 108




--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

Form: 20L2351 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION ULTRASONIC CONTACT-TYPE 6 SPECIFICATION IDENTIFICATIONS2 LEVEL SWITCH 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 PROCESS CONNECTION 60 SWITCH MECHANISM continued12 Body/Fitting type 61 Enclosure material13 Process conn nominal size Rating 62 Exterior coating material14 Process conn termn type Style 6315 Wetted material 6416 Flange/Fitting material 6517 Seal/O ring material 66 PERFORMANCE CHARACTERISTICS18 67 Max press at design temp At19 68 Min working temperature Max20 SENSING ELEMENT 69 Repeatability/Sensitivity21 Configuration type 70 Min ambient working temp Max22 Nominal temp rating 71 Contacts ac rating At Max23 Number of sensors 72 Contacts dc rating At Max24 Probe diameter 73 Max sensor to receiver lg25 Insertion length 7426 Integral cable length 7527 Self test type 7628 Cert/Approval type 7729 7830 7931 8032 CONNECTION HEAD OR PREAMPLIFIER 8133 Type 8234 Output signal type 8335 Enclosure type no/class 8436 Signal power source 85 ACCESSORIES37 Gain type 86 Connecting cables length38 Cert/Approval type 87 Mounting hardware39 Mounting location/type 88 External relay40 Failure/Diagnostic action 89 Intrinsic safety barrier41 Enclosure material 9042 9143 9244 SWITCH MECHANISM 93 SPECIAL REQUIREMENTS45 Housing type 94 Custom tag46 Element style 95 Reference specification47 Input signal type 96 Compliance standard48 Output signal type 9749 Enclosure type no/class 9850 Control logic 9951 Gain type 100 PHYSICAL DATA52 Signal power source 101 Estimated weight53 Contacts arrangement Quantity 102 Overall height54 Failsafe style 103 Removal clearance55 Integral indicator style 104 Signal conn nominal size Style56 Cert/Approval type 105 Mfr reference dwg57 Mounting location/type 10658 Failure/Diagnostic action 10759 Switch time delay 108

110 CALIBRATIONS AND TEST SETPOINT OUTPUT111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV ACTION LRV URV112 Lg conn to sp 1-Output113 Lg conn to sp 2-Output114 Lg conn to sp 3-Output115 Lg conn to sp 4-Output116117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

Form: 20L2371 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION ROTARY LEVEL SWITCH 6 SPECIFICATION IDENTIFICATIONS2 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 PROCESS CONNECTION 60 PERFORMANCE CHARACTERISTICS12 Body type 61 Max press at design temp At13 Process conn nominal size Rating 62 Min working temperature Max14 Process conn termn type Style 63 Min material density Max15 Wetted material 64 Min ambient working temp Max16 Seal/O ring material 65 Contacts ac rating At max17 66 Contacts dc rating At max18 6719 6820 SENSING ELEMENT 6921 Sensor type 7022 Nominal size 7123 Shaft coupling type 7224 Shaft guard style 7325 Extension shaft length 7426 Sensor material 7527 Extension/Cable material 7628 Shaft material 7729 7830 7931 8032 SWITCH MECHANISM 8133 Housing type 8234 Motor style 8335 Output signal type 8436 Enclosure type no/class 8537 Signal power source 86 ACCESSORIES38 Contacts arrangement Quantity 87 Mounting hardware39 Failsafe style 8840 Integral indicator style 8941 Cert/Approval type 9042 Failure/Diagnostic action 9143 Enclosure material 9244 93 SPECIAL REQUIREMENTS45 94 Custom tag46 95 Reference specification47 96 Compliance standard48 9749 9850 9951 100 PHYSICAL DATA52 101 Estimated weight53 102 Overall height54 103 Removal clearance55 104 Signal conn nominal size Style56 105 Mfr reference dwg57 10658 10759 108

110 CALIBRATIONS AND TEST SETPOINT OUTPUT111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV ACTION LRV URV112 Level setpoint-Output113114115116117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

Form: 20L2501 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION LIQUID LEVEL GAGE GLASS 6 SPECIFICATION IDENTIFICATIONS2 w/wo ILLUMINATOR 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 CHAMBER AND COVER 60 GAGE VALVES cpntinued12 Chamber type 61 Gage/Glass conn type Style13 Process conn nominal size Rating 62 Vent/Drain conn nom size Rating14 Process conn termn type Style 63 Vent/Drain conn type Style15 Flange facing finish 64 Max press at design temp At16 Process conn location 65 Vessel union/shank type17 Vent/Drain conn nom size Rating 66 Gage union/conn type18 Vent/Drain conn type Style 67 Seat type19 Nominal pressure 68 Heating/Cooling type20 Number of sections 69 Hand actuator style21 Weld pad radius size 70 Stem style22 Vent/Drain plug type 71 Body-Bonnet material23 Support plates lct 72 Trim material24 Heating/Cooling type 73 Ball check shutoff matl25 Chamber material 7426 Cover material 7527 Lining material 76 GAGE ILLUMINATOR28 Bolting material 77 Illumination type29 Exterior treatment matl 78 Power source30 Gasket material 79 Enclosure type no/class31 Cushion material 80 Cert/Approval type32 8133 82 PERFORMANCE CHARACTERISTICS34 GAGE GLASS 83 Max press at design temp At35 Glass type 84 Min working temperature Max36 Glass nominal size 85 Max working pressure37 Frost-proof extension lg 8638 Visible length 8739 Glass/Tube protector type 88 ACCESSORIES40 Glass/Tube material 89 Gage scale divisions41 Shield material-thickness 90 Gage scale material42 91 Vent valves material43 92 Drain valves material44 INTERCONNECTING ASSEMBLY 93 Bleed fitting material45 Interconnection type 94 Flexible insulation46 Nipple/Piping nom size Schedule no 9547 Valve offset orientation 96 SPECIAL REQUIREMENTS48 Gage orientation 97 Custom tag49 Assembled by 98 Reference specification50 Nipple/Piping material 99 Compliance standard51 Exterior coating material 100 Construction code52 101 Cert/Approval type53 10254 GAGE VALVES 103 PHYSICAL DATA55 Valve body type 104 Estimated weight56 Bonnet style 105 Gage overall length57 Vessel conn nominal size Rating 106 Min vessel centers58 Vessel conn termn type Style 107 Mfr reference dwg59 Gage/Glass conn nom size Rating 108

110 CALIBRATIONS AND TEST INPUT ORTEST SCALE111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV LRV URV112 Level -Scale113 Test pressure114115116117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

Form: 20L2511 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION MAGNETIC LIQUID LEVEL GAGE OR 6 SPECIFICATION IDENTIFICATIONS2 INDICATOR w/wo SWITCHES 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 CAGE OR CHAMBER 60 PERFORMANCE CHARACTERISTICS12 Cage/Chamber type 61 Max press at design temp At13 Process conn nominal size Rating 62 Min working temperature Max14 Process conn termn type Style 63 Repeatability15 Lower conn location Upper 64 Min sp gr differential16 Top connection style Bottom 65 Deadband rating17 Vent/Drain conn nom size Rating 66 Min ambient working temp Max18 Vent/Drain termn type Style 67 Contacts ac rating At max19 Cage/Chamber pipe sched 68 Contacts dc rating At max20 Cage/Chamber material 6921 Lining material 7022 Bolting material 7123 Flange material 7224 Gasket material 7325 7426 7527 SENSING ELEMENT 7628 Sensor Type 7729 Sp gr Lower Range-Limit URL 7830 Min level span Max 7931 Sensor quantity 8032 Extension length 8133 Float/Displacer length 8234 Float/Displacer material 8335 8436 85 ACCESSORIES37 GAGE OR INDICATOR 86 Heating kit style38 Type 87 Isolation valve style39 Seal style 88 Vent/Drain valve style40 Visible length 8941 Gage scale divisions 9042 Orientation to conn 9143 Bicolor wafer colors 92 SPECIAL REQUIREMENTS44 Cover material 93 Custom tag45 Indicator material 94 Reference specification46 95 Special preparation47 96 Compliance standard48 SWITCH MECHANISM 97 Construction code49 Housing type 9850 Element style 9951 Output signal type 100 PHYSICAL DATA52 Enclosure type no/class 101 Estimated weight53 Signal power source 102 Overall height54 Contacts arrangement Quantity 103 Removal clearance55 Signal termination type 104 Upper to lower conn lg56 Cert/Approval type 105 Lower to drain conn lg57 Enclosure material 106 Signal conn nominal size Style58 107 Mfr reference dwg59 108

110 CALIBRATIONS AND TEST INPUT OR SETPOINT SCALE111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV ACTION LRV URV112 Level-Scale113 Level setpoint 1-Output114 Level setpoint 2-Output115 Test pressure116117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

Form: 20P2001 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION PRESSURE GAUGE 6 SPECIFICATION IDENTIFICATIONS2 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 OPERATING PARAMETERS 60 DIAL AND POINTER12 Project number Sub project no 61 Dial scale type13 Project 62 Pointer adjustment14 Enterprise 63 Graduations and color15 Site 64 Scale range type16 Area Cell Unit 65 Dial material17 Related equipment 6618 Service 6719 6820 P&ID/Reference dwg number 69 SIPHON21 Material name 70 Siphon type22 Minimum pressure 71 End conn nominal size Style23 Normal pressure 72 Overall length24 Maximum pressure 73 Siphon material25 Normal temperature 7426 Maximum temperature 7527 Material phase 7628 77 PERFORMANCE CHARACTERISTICS29 78 Max press at design temp At30 79 Min working temperature Max31 PROCESS CONNECTION AND CASE 80 Min ambient working temp Max32 Case type 8133 Case style 8234 Gauge size 8335 Process conn nominal size Style 8436 Process conn location 85 ACCESSORIES37 Case pressure relief type 86 Pressure limit valve matl38 Ring style 87 Restrictor style39 Mounting type 88 Pressure snubber matl40 Case material 89 Pulsation dampener matl41 Ring material 9042 Exterior treatment-color 9143 Window material 92 SPECIAL REQUIREMENTS44 Stem material 93 Custom tag45 Gasket/O ring material 94 Reference specification46 Liquid fill material 95 Special preparation47 96 Compliance standard48 97 Service design49 9850 PRESSURE ELEMENT AND MOVEMENT 9951 Elastic element type 10052 Movement style 101 PHYSICAL DATA53 Nominal accuracy grade 102 Estimated weight54 Joint type 103 Maximum thickness55 Element material 104 Max case outside dia56 Movement material 105 Mfr reference dwg57 10658 10759 108

110 CALIBRATIONS AND TEST SCALE111 TAG NO/FUNCTIONAL IDENT PRESSURE OR SCALE LRV URV112 Pressure/Scale 1113 Pressure/Scale 2114115116117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

Form: 20P2011 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION PRESSURE GAUGE 6 SPECIFICATION IDENTIFICATIONS2 WITH DIAPHRAGM SEAL 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 OPERATING PARAMETERS 60 DIAL AND POINTER continued12 Project number Sub project no 61 Graduations and color13 Project 62 Scale range type14 Enterprise 63 Dial material15 Site 6416 Area Cell Unit 6517 Related equipment 66 DIAPHRAGM SEAL18 Service 67 Seal type19 68 Process conn nom size Rating20 P&ID/Reference dwg number 69 Process conn termn type Style21 Material name 70 Diaphragm extension lg22 Minimum pressure 71 Flushing conn quantity23 Normal pressure 72 Capillary diameter Length24 Maximum pressure 73 Instrument conn nom size25 Normal temperature 74 Diaphragm/wall material26 Maximum temperature 75 Capillary-armor material27 Material phase 76 Bolting material28 77 Upper housing material29 78 Lower housing material30 PROCESS CONNECTION AND CASE 79 Gasket/O ring material31 Case type 80 Fill fluid material32 Case style 8133 Gauge size 8234 Process conn nominal size Style 83 PERFORMANCE CHARACTERISTICS35 Process conn location 84 Max press at design temp At36 Case pressure relief type 85 Min working temperature Max37 Ring style 86 Ambient temperature error38 Mounting type 87 Min ambient working temp Max39 Case material 8840 Ring material 8941 Exterior treatment-color 90 ACCESSORIES42 Window material 91 Locking device material43 Stem material 9244 Seal/O ring material 9345 Liquid fill material 9446 95 SPECIAL REQUIREMENTS47 96 Custom tag48 PRESSURE ELEMENT AND MOVEMENT 97 Reference specification49 Elastic element type 98 Special preparation50 Movement style 99 Compliance standard51 Nominal accuracy grade 100 Service design52 Joint type 10153 Element material 102 PHYSICAL DATA54 Movement material 103 Estimated weight55 104 Maximum thickness56 105 Max case outside dia57 DIAL AND POINTER 106 Mfr reference dwg58 Dial scale type 10759 Pointer adjustment 108

110 CALIBRATIONS AND TEST SCALE111 TAG NO/FUNCTIONAL IDENT PRESSURE OR SCALE LRV URV112 Pressure/Scale 1113 Pressure/Scale 2114115116117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

Form: 20P2101 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION DIFFERENTIAL PRESSURE GAUGE 6 SPECIFICATION IDENTIFICATIONS2 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 OPERATING PARAMETERS 60 DIAL AND POINTER12 Project number Sub project no 61 Dial scale type13 Project 62 Pointer adjustment14 Enterprise 63 Graduations and color15 Site 64 Scale range type16 Area Cell Unit 65 Dial material17 Related equipment 6618 Service 6719 6820 P&ID/Reference dwg number 69 SIPHON21 Material name 70 Siphon type22 Maximum pressure 71 End conn nominal size Style23 Maximum temperature 72 Overall length24 Material phase 73 Siphon material25 Min diff pressure 7426 Norm diff pressure 7527 Max diff pressure 7628 77 PERFORMANCE CHARACTERISTICS29 78 Max press at design temp At30 79 Min working temperature Max31 PROCESS CONNECTION AND CASE 80 Max diff pressure32 Case type 81 Min ambient working temp Max33 Case style 8234 Gauge size 8335 Process conn nominal size Style 8436 Process conn location 85 ACCESSORIES37 Case pressure relief type 86 Pressure limit valve matl38 Ring style 87 Restrictor style39 Mounting type 88 Pressure snubber matl40 Case material 89 Pulsation dampener matl41 Ring material 90 Scale overlays42 Exterior treatment-color 9143 Window material 92 SPECIAL REQUIREMENTS44 Stem material 93 Custom tag45 Gasket/O ring material 94 Reference specification46 Liquid fill material 95 Special preparation47 96 Compliance standard48 97 Service design49 9850 PRESSURE ELEMENT AND MOVEMENT 9951 Elastic element type 10052 Movement style 101 PHYSICAL DATA53 Nominal accuracy grade 102 Estimated weight54 Joint type 103 Maximum thickness55 Element material 104 Max case outside dia56 Movement material 105 Mfr reference dwg57 10658 10759 108

110 CALIBRATIONS AND TEST SCALE111 TAG NO/FUNCTIONAL IDENT PRESSURE OR SCALE LRV URV112 Diff pressure/Scale 1113 Diff pressure/Scale 2114115116117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

Form: 20P2201 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION PRESSURE TRANSMITTER 6 SPECIFICATION IDENTIFICATIONS2 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 TRANSMITTER BODY 60 PERFORMANCE CHARACTERISTICS12 Body/Flange type 61 Max press at design temp At13 Process conn nominal size Rating 62 Min working temperature Max14 Process conn termn type Style 63 Accuracy rating15 Vent/Drain location 64 Pressure LRL URL16 Mounting type 65 Min ambient working temp Max17 Body/Flange material 6618 Vent/Drain material 6719 Bolting material 6820 Flange adapter material 6921 Gasket/O ring material 7022 Mounting kit material 7123 7224 7325 7426 SENSING ELEMENT 7527 Detector type 7628 Min pressure span Max 7729 Diaphragm/Wetted material 7830 Fill fluid material 7931 8032 8133 8234 TRANSMITTER 8335 Output signal type 84 ACCESSORIES36 Enclosure type no/class 85 Air set filter style37 Characteristic curve 86 Air set gauges38 Digital communication std 87 Heating kit style39 Signal power source 88 Remote indicator style40 Transient protection 89 Manifold valve style41 Integral indicator style 9042 Signal termination type 91 SPECIAL REQUIREMENTS43 Cert/Approval type 92 Custom tag44 Span-Zero adjust lct 93 Reference specification45 Failure/Diagnostic action 94 Special preparation46 Enclosure material 95 Compliance standard47 96 Software configuration48 9749 9850 9951 100 PHYSICAL DATA52 101 Estimated weight53 102 Overall height54 103 Removal clearance55 104 Signal conn nominal Style56 105 Mfr reference dwg57 10658 10759 108

110 CALIBRATIONS AND TEST INPUT OUTPUT OR SCALE111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV ACTION LRV URV112 Pressure-Analog output113 Pressure-Scale114 Pressure-Digital output115 Temp-Digital output116117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125




--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

Form: 20P2211 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION PRESSURE TRANSMITTER 6 SPECIFICATION IDENTIFICATIONS2 WITH DIAPHRAGM SEAL 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 TRANSMITTER BODY 60 PERFORMANCE CHARACTERISTICS12 Body/Flange type 61 Max press at design temp At13 Process conn nominal size Rating 62 Min working temperature Max14 Process conn termn type Style 63 Accuracy rating15 Vent/Drain location 64 Pressure Lower Range-Limit URL16 Mounting type 65 Ambient temperature error17 Body/Flange material 66 Min ambient working temp Max18 Vent/Drain material 6719 Bolting material 6820 Flange adapter material 6921 Gasket/O ring material 7022 Mounting kit material 7123 7224 SENSING ELEMENT 7325 Detector type 7426 Min pressure span Max 7527 Diaphragm/Wetted material 7628 Fill fluid material 7729 7830 TRANSMITTER 7931 Output signal type 8032 Enclosure type no/class 8133 Characteristic curve 8234 Digital communication std 8335 Signal power source 84 ACCESSORIES36 Transient protection 85 Air set filter style37 Integral indicator style 86 Air set gauges38 Signal termination type 87 Heating kit style39 Cert/Approval type 88 Remote indicator style40 Span-Zero adjust lct 8941 Failure/Diagnostic action 9042 Enclosure material 91 SPECIAL REQUIREMENTS43 92 Custom tag44 DIAPHRAGM SEAL 93 Reference specification45 Seal type 94 Special preparation46 Process conn nominal size Rating 95 Compliance standard47 Process conn termn type Style 96 Software configuration48 Diaphragm extension lg 9749 Flushing conn quantity 9850 Instrument conn nom size 9951 Capillary/Fitting dia Length 100 PHYSICAL DATA52 Diaphragm material 101 Estimated weight53 Capillary-armor matl 102 Overall height54 Bolting material 103 Removal clearance55 Upper housing material 104 Signal conn nominal size Style56 Lower housing/Flange matl 105 Mfr reference dwg57 Gasket/O ring material 10658 Fill fluid material 10759 108

110 CALIBRATIONS AND TEST INPUT OUTPUT OR SCALE111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV ACTION LRV URV112 Pressure-Analog output113 Pressure-Scale114 Pressure-Digital output115 Temp-Digital output116117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125




--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

Form: 20P2301 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION DIFFERENTIAL PRESSURE 6 SPECIFICATION IDENTIFICATIONS2 TRANSMITTER 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 TRANSMITTER BODY 60 PERFORMANCE CHARACTERISTICS12 Body/Flange type 61 Max press at design temp At13 Process conn nominal size Rating 62 Min working temperature Max14 Process conn termn type Style 63 Accuracy rating15 Vent/Drain location 64 Diff pressure LRL URL16 Mounting type 65 Min ambient working temp Max17 Body/Flange material 6618 Vent/Drain material 6719 Bolting material 6820 Flange adapter material 6921 Gasket/O ring material 7022 Mounting kit material 7123 7224 7325 7426 SENSING ELEMENT 7527 Detector type 7628 Min diff press span Max 7729 Diaphragm/Wetted material 7830 Fill fluid material 7931 8032 8133 8234 TRANSMITTER 8335 Output signal type 84 ACCESSORIES36 Enclosure type no/class 85 Air set filter style37 Characteristic curve 86 Air set gauges38 Digital communication std 87 Heating kit style39 Signal power source 88 Remote indicator style40 Transient protection 89 Manifold valve style41 Integral indicator style 9042 Signal termination type 91 SPECIAL REQUIREMENTS43 Cert/Approval type 92 Custom tag44 Span-Zero adjust lct 93 Reference specification45 Failure/Diagnostic action 94 Special preparation46 Enclosure material 95 Compliance standard47 96 Software configuration48 9749 9850 9951 100 PHYSICAL DATA52 101 Estimated weight53 102 Overall height54 103 Removal clearance55 104 Signal con nominal size Style56 105 Mfr reference dwg57 10658 10759 108

110 CALIBRATIONS AND TEST INPUT OUTPUT OR SCALE111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV ACTION LRV URV112 Diff press-Analog output113 Diff pressure-Scale114 Diff press-Digital output115 Press-Digital output116 Temp-Digital output117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125




--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

Form: 20P2311 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION DIFFERENTIAL PRESSURE TRANS- 6 SPECIFICATION IDENTIFICATIONS2 MITTER WITH DIAPHRAGM SEALS 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 TRANSMITTER BODY 60 LOW SIDE SEAL12 Body/Flange type 61 Seal type13 Process conn nominal size Rating 62 Process conn nominal size Rating14 Process conn termn type Style 63 Process conn termn type Style15 Vent/Drain location 64 Diaphragm extension lg16 Mounting type 65 Flushing conn quantity17 Body/Flange material 66 Instrument conn nom size18 Vent/Drain material 67 Capillary/Fitting dia Length19 Bolting material 68 Diaphragm material20 Flange adapter material 69 Capillary-armor material21 Gasket/O ring material 70 Bolting material22 Mounting kit material 71 Upper housing material23 72 Lower housing/Flange matl24 SENSING ELEMENT 73 Gasket/O ring material25 Detector type 74 Fill fluid material26 Min diff pressure span Max 7527 Diaphragm/Wetted material 76 PERFORMANCE CHARACTERISTICS28 Fill fluid material 77 Max press at design temp At29 78 Min working temperature Max30 TRANSMITTER 79 Accuracy rating31 Output signal type 80 Diff pressure LRL URL32 Enclosure type no/class 81 Fill fluid sp gr At temp33 Characteristic curve 82 Ambient temperature error34 Digital communication std 83 Min ambient working temp Max35 Signal power source 8436 Transient protection 8537 Integral indicator style 8638 Signal termination type 87 ACCESSORIES39 Cert/Approval type 88 Air set filter style40 Span-Zero adjust lct 89 Air set gauges41 Failure/Diagnostic action 90 Heating kit style42 Enclosure material 91 Remote indicator style43 9244 HIGH SIDE SEAL 93 SPECIAL REQUIREMENTS45 Seal type 94 Custom tag46 Process conn nominal size Rating 95 Reference specification47 Process conn termn type Style 96 Special preparation48 Diaphragm extension lg 97 Compliance standard49 Flushing conn quantity 98 Software configuration50 Instrument conn nom size 9951 Capillary/Fitting dia Length 10052 Diaphragm material 101 PHYSICAL DATA53 Capillary-armor matl 102 Estimated weight54 Bolting material 103 Overall height55 Upper housing material 104 Removal clearance56 Lower housing/Flange matl 105 Signal conn nominal size Style57 Gasket/O ring material 106 Mfr reference dwg58 Fill fluid material 10759 108

110 CALIBRATIONS AND TEST INPUT OUTPUT OR SCALE111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV ACTION LRV URV112 Diff press-Analog output113 Diff press-Scale114 Diff press-Digital output115 Press-Digital output116 Temp-Digital output117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125




--`,,```,,,,````-`-`,,`,,`,`,,`--- //^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

Form: 20P2401 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION PRESSURE SWITCH 6 SPECIFICATION IDENTIFICATIONS2 w/wo TRANSMITTER 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 SWITCH BODY 59 PERFORMANCE CHARACTERISTICS12 Body type 60 Max press at design temp At13 Process conn nominal size Rating 61 Min working temperature Max14 Process conn termn type Style 62 Output accuracy rating15 Body material 63 Repeatability16 Seal/O ring material 64 Press Lower Range-limit URL17 65 Max overrange limit18 66 Dead band rating19 67 Min ambient working temp Max20 SENSING ELEMENT 68 Contacts ac rating At max21 Sensor element type 69 Contacts dc rating At max22 Adjustable LRL URL 7023 Diaphragm/Wetted material 7124 7225 7326 7427 SWITCH MECHANISM w/wo TRANSMITTER 7528 Housing type 7629 Element Style 7730 Output signal type 7831 Enclosure type no/class 7932 Reset style 8033 Set point Adjustment type 8134 Signal power source 8235 Measurement type 83 ACCESSORIES36 Contacts arrangement Quantity 84 Sealed leads adapter37 Failsafe style 85 Breather/Drain style38 Integral indicator style 8639 Signal termination type 8740 Cert/Approval type 8841 Mounting type 8942 Dead band type 90 SPECIAL REQUIREMENTS43 Enclosure material 91 Custom tag44 Exterior treatment matl 92 Reference specification45 93 Special preparation46 94 Compliance standard47 9548 9649 9750 98 PHYSICAL DATA51 99 Estimated weight52 100 Overall height53 101 Removal clearance54 102 Signal conn nominal size Style55 103 Mfr reference dwg56 10457 10558 106

110 CALIBRATIONS AND TEST INPUT/SETPOINT/TEST OUTPUT OR SCALE111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV ACTION LRV URV112 Press setpoint 1-Output113 Press setpoint 2-Output114 Pressure-Analog output115 Pressure-Scale116117118119 COMPONENT IDENTIFICATIONS120 COMPONENT TYPE MANUFACTURER MODEL NUMBER121122123124125126




--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

Form: 20P2501 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION DIFFERENTIAL PRESSURE SWITCH 6 SPECIFICATION IDENTIFICATIONS2 w/wo TRANSMITTER 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 SWITCH BODY 59 PERFORMANCE CHARACTERISTICS12 Body type 60 Max press at design temp At13 Process conn nominal size Rating 61 Min working temperature Max14 Process conn termn type Style 62 Output accuracy rating15 Body material 63 Repeatability16 Seal/O ring material 64 Diff press Lower Range-Limit URL17 65 Max overrange limit18 66 Dead band rating19 67 Min ambient working temp Max20 SENSING ELEMENT 68 Contacts ac rating At max21 Sensor element type 69 Contacts dc rating At max22 Adjustable LRL URL 7023 Diaphragm/Wetted material 7124 7225 7326 7427 SWITCH MECHANISM w/wo TRANSMITTER 7528 Housing type 7629 Element Style 7730 Output signal type 7831 Enclosure type no/class 7932 Reset style 8033 Set point Adjustment type 8134 Signal power source 8235 Measurement type 83 ACCESSORIES36 Contacts arrangement Quantity 84 Sealed leads adapter37 Failsafe style 85 Breather/Drain style38 Integral indicator style 8639 Signal termination type 8740 Cert/Approval type 8841 Mounting type 8942 Dead band type 90 SPECIAL REQUIREMENTS43 Enclosure material 91 Custom tag44 Exterior coating material 92 Reference specification45 93 Special preparation46 94 Compliance standard47 9548 9649 9750 98 PHYSICAL DATA51 99 Estimated weight52 100 Overall height53 101 Removal clearance54 102 Signal conn nominal size Style55 103 Mfr reference dwg56 10457 10558 106

110 CALIBRATIONS AND TEST INPUT OR SETPOINT OUTPUT OR SCALE111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV ACTION LRV URV112 DP setpoint 1-Output113 DP setpoint 2-Output114 Diff press-Analog output115 Diff pressure-Scale116117118119 COMPONENT IDENTIFICATIONS120 COMPONENT TYPE MANUFACTURER MODEL NUMBER121122123124125126




--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

1 RESPONSIBLE ORGANIZATION RUPTURE DISC ASSEMBLY 6 SPECIFICATION IDENTIFICATIONS2 w/wo BURST SENSOR 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 DISC HOLDER 60 PERFORMANCE CHARACTERISTICS12 Assembly type 61 Min working temperature Max13 Disc holder style 62 Max opr pressure ratio14 Inlet conn nominal size Rating 63 Rupture/Burst tolerance Ref15 Inlet conn termn type Style 64 Flow resistance factor16 Outlet conn nominal size Rating 65 Mfg design range LRL URL17 Outlet conn termn type Style 66 Minimum net flow area18 End conn schedule no 67 Contact ac rating At max19 Gauge tap conn nom size Style 68 Contact dc rating At max20 Companion flange design 6921 Preassembly method 7022 Knife blade type 7123 Seat style 7224 Jack screws 7325 Alignment style 7426 Lifting device 7527 Inlet base/Body matl 7628 Outlet holddown/Body matl 7729 Lining/Coating material 7830 Bolting material 7931 Gasket/O ring material 8032 81 ACCESSORIES33 82 Spare disc quantity34 RUPTURE SENSOR 83 Baffle plate35 Sensor type 84 Excess flow valve36 Configuration style 85 Nipple and tee37 Contacts arrangement 86 Pressure gauge38 Lead wire length 8739 Signal termination type 8840 Cert/Approval type 8941 Sensor material 90 SPECIAL REQUIREMENTS42 Membrane/Seal material 91 Custom tag43 Gasket material 92 Reference specification44 93 Special preparation45 RUPTURE DISC 94 Compliance standard46 Disc type 95 Construction code47 Disc shape configuration 96 Certification48 Disc nominal size 97 Special testing49 Nominal mfg range 9850 Prot liner/cover location 9951 Ring location 10052 Disc material 101 PHYSICAL DATA 53 Seal material 102 Estimated weight54 Vacuum support material 103 Overall height55 Ring material 104 Outside diameter56 Prot liner/cover matl 105 Mfr reference dwg57 Gasket material 10658 Coating material 10759 108

110 CALIBRATIONS AND TEST TEST111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/SCALE PRESSURE TEMPERATURE112 Positive burst pressure113 Vacuum burst pressure114115116117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125


Form: 20P2901 Rev 0 © 2004 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

1 RESPONSIBLE ORGANIZATION PRESSURE RELIEF VALVE 6 SPECIFICATION IDENTIFICATIONS2 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 VALVE BODY 60 PERFORMANCE CHARACTERISTICS12 Body type 61 Max inlet press at temp At13 Nozzle style 62 Max back press at temp At14 Valve nominal size 63 Min working temperature Max15 Inlet conn nominal size Rating 64 Set pressure LRL URL16 Inlet conn termn type Style 65 Rated relieving capacity At17 Outlet conn nominal size Rating 66 Rated coef of discharge18 Outlet conn termn type Style 67 Rated seat leakage rate19 Body/Cylinder material 68 Actual discharge area20 Nozzle/Base material 6921 Bolting material 7022 Separable flange matl 7123 Gasket/O ring material 7224 7325 7426 7527 VALVE TRIM 7628 Trim type 7729 Seat style 7830 Orifice designation Effective area 7931 Blowdown type 80 ACCESSORIES32 Disc holder material 81 Silencer33 Disc insert material 82 Weatherhood34 Guide material 83 Drip pan elbow35 O ring/Soft seat matl 84 Bugproof vent36 Bellows material 8537 Adjusting ring material 8638 8739 88 SPECIAL REQUIREMENTS40 89 Custom tag41 SPRING AND BONNET 90 Reference specification42 Bonnet type 91 Special preparation43 Bonnet style 92 Compliance standard44 Lifting device type 93 Construction code45 Cap type 94 Certification46 Restricted lift style 95 Special inspection47 Bonnet/Yoke material 96 Service design48 Spring material 9749 Spring washer/Step matl 9850 Adjusting screw/Bolt matl 99 PHYSICAL DATA 51 Stem/Spindle material 100 Estimated weight52 Cap material 101 Overall height53 Gasket/O ring matl 102 Dismantle clearance54 103 Inlet center-to face lg55 104 Outlet center-to face lg56 105 Mfr reference dwg57 10658 10759 108

110 CALIBRATIONS AND TEST INPUT OR SETPOINT111 TAG NUMBER TEST LRV URV112 CDTP-Setpoint113 Blowdown-Setpoint114115116117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125


Form: 20P2921 Rev 0 © 2004 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

Form: 20R2201 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION RECEIVER GAUGE 6 SPECIFICATION IDENTIFICATIONS2 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 SIGNAL CONNECTION AND CASE 38 DIAL AND POINTER12 Case type 39 Dial scale type13 Gauge style 40 Pointer adjustment14 Gauge size 41 Graduations and color15 Signal conn nominal size Style 42 Scale range type16 Signal conn location 43 Dial material17 Case pressure relief type 4418 Ring style 4519 Mounting type 46 PERFORMANCE CHARACTERISTICS20 Case material 47 Min ambient working temp Max21 Ring material 4822 Exterior treatment-color 4923 Window material 50 ACCESSORIES24 Stem material 51 Mounting hardware25 Gasket/O ring material 5226 5327 54 SPECIAL REQUIREMENTS28 PRESSURE ELEMENT AND MOVEMENT 55 Custom tag29 Elastic element type 56 Reference specification30 Movement style 57 Compliance standard31 Nominal accuracy grade 5832 Joint type 59 PHYSICAL DATA33 Internal stops 60 Estimated weight34 Element material 61 Maximum thickness35 Movement material 62 Max case outside dia36 63 Mfr reference dwg37 6465 CALIBRATIONS AND TEST INPUT SCALE66 TAG NO/FUNCTIONAL IDENT PRESSURE OR SCALE LRV URV LRV URV67 Input signal-Scale 168 Input signal-Scale 26970717273747576777879808182838485868788 COMPONENT IDENTIFICATIONS89 COMPONENT TYPE MANUFACTURER MODEL NUMBER90919293949596979899

100101102Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

Form: 20T2001 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION BIMETALLIC THERMOMETER 6 SPECIFICATION IDENTIFICATIONS2 w/wo THERMOWELL 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 OPERATING PARAMETERS 60 THERMOWELL OR PROTECTING TUBE12 Project number Sub project no 61 Construction type13 Project 62 Shank style14 Enterprise 63 Process conn nominal size Rating15 Site 64 Process conn termn type Style16 Area Cell Unit 65 Internal conn nom size Style17 Related equipment 66 Bore diameter18 Service 67 Outside dia at support19 68 Outside diameter at tip20 P&ID/Reference dwg number 69 Insertion length “U”21 Material name 70 Lagging extension lg “T”22 Maximum pressure 71 Thermowell/Tube material23 Minimum temperature 72 Sheath material-thickness24 Normal temperature 7325 Maximum temperature 7426 Material phase 7527 Maximum fluid velocity 76 PERFORMANCE CHARACTERISTICS28 77 Max press at design temp At29 78 Min working temperature Max30 PROCESS CONNECTION AND CASE 79 Max fluid velocity limit At temp31 Case type 80 Sensitive portion length32 Case style 81 Min ambient working temp Max33 Case size 8234 Connector conn nom size 8335 Connector conn type Style 8436 Connection location 85 ACCESSORIES37 Ring style 86 Bushing nominal size38 Stem outside diameter Length 87 Bushing material39 Stem/Bulb material 8840 Case material 8941 Ring material 9042 Exterior treatment-color 9143 Window material 92 SPECIAL REQUIREMENTS44 Connector material 93 Custom tag45 94 Reference specification46 95 Compliance standard47 SENSING ELEMENT 96 Construction code48 Element type 97 Calculation report49 Nominal accuracy grade 9850 9951 100 PHYSICAL DATA52 101 Estimated weight53 DIAL AND POINTER 102 Removal clearance54 Dial scale type 103 Maximum thickness55 Pointer adjustment 104 Max case outside dia56 Graduations and color 105 Mfr reference dwg57 10658 10759 108

110 CALIBRATIONS AND TEST TEST SCALE111 TAG NO/FUNCTIONAL IDENT MEAS OR TEST URV LRV URV112 Temperature/Scale 1113 Temperature/Scale 2114 Test pressure115116117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

Form: 20T2101 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION FILLED-SYSTEM THERMOMETER 6 SPECIFICATION IDENTIFICATIONS2 ASSEMBLY w/wo THERMOWELL 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 OPERATING PARAMETERS 60 THERMOWELL/PROTECTING TUBE continued12 Project number Sub project no 61 Graduations and color13 Project 6214 Enterprise 6315 Site 64 THERMOWELL OR PROTECTING TUBE16 Area Cell Unit 65 Construction type17 Related equipment 66 Shank style18 Service 67 Process conn nominal size Rating19 68 Process conn termn type Style20 P&ID/Reference dwg number 69 Internal conn nom size Style21 Material name 70 Bore diameter22 Maximum pressure 71 Outside dia at support23 Minimum temperature 72 Outside diameter at tip24 Normal temperature 73 Insertion length “U”25 Maximum temperature 74 Lagging extension lg “T”26 Material phase 75 Thermowell/Tube material27 Maximum fluid velocity 76 Sheath material-thickness28 7729 7830 BULB AND CASE 79 PERFORMANCE CHARACTERISTICS31 Case type 80 Max press at design temp At32 Stem/Bulb extension style 81 Min working temperature Max33 Case size 82 Max fluid velocity limit At temp34 Connector conn nom size 83 Sensitive portion length35 Connector conn type Style 84 Ambient temperature error36 Connection location 85 Min ambient working temp Max37 Ring style 8638 Stem/Bulb outside dia Length 8739 Mounting type 88 ACCESSORIES40 Stem/Bulb material 89 Bushing nominal size41 Case-Ring material 90 Bushing material42 Exterior treatment-color 9143 Window material 9244 Connector material 9345 9446 95 SPECIAL REQUIREMENTS47 CAPILLARY AND SENSING ELEMENT 96 Custom tag48 Thermal system type 97 Reference specification49 Compensation style 98 Compliance standard50 Nominal accuracy grade 99 Construction code51 Capillary length 100 Calculation report52 Capillary material 10153 Coating-armor material 102 PHYSICAL DATA54 103 Estimated weight55 104 Removal clearance56 105 Maximum thickness57 DIAL AND POINTER 106 Max case outside dia58 Dial scale type 107 Mfr reference dwg59 Pointer adjustment 108

110 CALIBRATIONS AND TEST TEST SCALE111 TAG NO/FUNCTIONAL IDENT TEMP OR TEST URV LRV URV112 Temperature/Scale 1113 Temperature/Scale 2114 Test pressure115116117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

Form: 20T2111 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION FILLED-SYSTEM TEMPERATURE 6 SPECIFICATION IDENTIFICATIONS2 SWITCH w/wo THERMOWELL 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 PROCESS CONNECTION AND BULB 60 THERMOWELL OR PROTECTING TUBE12 Bulb type 61 Construction type13 Stem/Bulb extension style 62 Shank style14 Connector conn nom size 63 Process conn nominal size Rating15 Connector conn type Style 64 Process conn termn type Style16 Fitting type 65 Internal conn nom size Style17 Stem/Bulb diameter Length 66 Bore diameter18 Bulb extension length 67 Outside dia at support19 Stem/Bulb material 68 Outside dia at tip20 Connector material 69 Insertion length “U”21 70 Lagging extension lg “T”22 71 Thermowell/Tube material23 72 Sheath material-thickness24 CAPILLARY AND SENSING ELEMENT 7325 Thermal system type 7426 Compensation style 75 PERFORMANCE CHARACTERISTICS27 Temperature LRL URL 76 Max press at design temp At28 Capillary length 77 Min working temperature Max29 Capillary material 78 Max fluid velocity limit At temp30 Coating-armor material 79 Repeatability31 80 Max overrange limit32 81 Ambient temperature error33 82 Dead band rating34 SWITCH MECHANISM 83 Min ambient working temp Max35 Type 84 Contacts ac rating At max36 Element style 85 Contacts dc rating At max37 Enclosure type no/class 8638 Reset style 8739 Set point adjustment lct 88 ACCESSORIES40 Signal power source 89 Bushing nominal size41 Dead band type 90 Bushing material42 Contacts arrangement Quantity 91 Sealed leads adapter43 Integral indicator style 92 Breather/Drain style44 Signal termination type 9345 Cert/Approval type 94 SPECIAL REQUIREMENTS46 Mounting type 95 Custom tag47 Signal conn orientation 96 Reference specification48 Enclosure material 97 Special preparation49 Exterior coating material 98 Compliance standard50 99 Calculation report51 10052 10153 102 PHYSICAL DATA54 103 Estimated weight55 104 Overall height56 105 Removal clearance57 106 Signal conn nominal size Style58 107 Mfr reference dwg59 108

110 CALIBRATIONS AND TEST INPUT/SETPOINT/TEST OUTPUT OR SCALE111 TAG NO/FUNCTIONAL IDENT MEAS OR TEST LRV URV ACTION LRV URV112 Temp setpoint 1-Output113 Temp setpoint 2-Output114 Temperature-Scale115 Test pressure116117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

Form: 20T2121 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION FILLED-SYSTEM TEMPERATURE 6 SPECIFICATION IDENTIFICATIONS2 TRANSMITTER w/wo THERMOWELL 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 PROCESS CONNECTION AND BULB 60 THERMOWELL OR PROTECTING TUBE12 Bulb type 61 Construction type13 Stem/Bulb extension style 62 Shank style14 Connector conn nom size 63 Process conn nominal size Rating15 Connector conn type Style 64 Process conn termn type Style16 Fitting type 65 Internal conn nom size Style17 Stem/Bulb diameter Length 66 Bore diameter18 Bulb extension length 67 Outside dia at support19 Stem/Bulb material 68 Outside dia at tip20 Connector material 69 Insertion length “U”21 Packing material 70 Lagging extension lg “T”22 71 Thermowell/tube material23 72 Sheath material-thickness:24 7325 CAPILLARY AND SENSING ELEMENT 7426 Thermal system type 7527 Compensation style 76 PERFORMANCE CHARACTERISTICS28 Temperature LRL URL 77 Max press at design temp At29 Min temperature span Max 78 Min working temperature Max30 Capillary length 79 Max fluid velocity limit At temp31 Capillary material 80 Accuracy rating32 Coating-armor material 81 Max overrange limit33 82 Ambient temperature error34 83 Min ambient working temp Max35 8436 TRANSMITTER 8537 Housing type 8638 Output signal type 87 ACCESSORIES39 Enclosure type no/class 88 Bushing nominal size40 Signal power source 89 Bushing material41 Integral indicator style 90 Air set filter style42 Signal termination type 91 Pressure gauges43 Cert/Approval type 9244 Mounting type 93 SPECIAL REQUIREMENTS45 Enclosure material 94 Custom tag46 95 Reference specification47 96 Compliance standard48 97 Construction code49 98 Calculation report50 9951 10052 101 PHYSICAL DATA53 102 Estimated weight54 103 Overall height55 104 Removal clearance56 105 Signal conn nominal size Style57 106 Mfr reference dwg58 10759 108

110 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT OR SCALE111 TAG NO/FUNCTIONAL IDENT MEAS OR TEST LRV URV ACTION LRV URV112 Temp-Analog output113 Temperature-Scale114 Test pressure115116117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

Form: 20T2201 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION RTD ASSEMBLY 6 SPECIFICATION IDENTIFICATIONS2 w/wo THERMOWELL 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 PROTECTIVE SHEATH AND FITTING 60 THERMOWELL OR PROTECTING TUBE12 Housing type 61 Construction type13 Pad/Collar type 62 Shank style14 Fitting conn nominal size Style 63 Process conn nominal size Rating15 Mounting fitting type 64 Process conn termn type Style16 Sheath alignment 65 Internal conn nom size Style17 Sheath outside diameter Length 66 Bore diameter18 Spring loading 67 Outside dia at support19 Sheath material 68 Outside dia at tip20 Fitting material 69 Insertion length “U”21 70 Lagging extension lg “T”22 SENSING ELEMENT 71 Thermowell/Tube material23 Sensor type 72 Sheath material-thickness24 Sensor quantity 7325 Temperature coefficient 7426 Tolerance class 75 PERFORMANCE CHARACTERISTICS27 Nominal resistance At temp 76 Max press at design temp At28 Configuration-no of wires 77 Min working temperature Max29 Sensor material 78 Max fluid velocity limit At temp30 Insulator material 79 Temp Lower Range-Limit URL31 80 Min insertion length32 LEAD WIRE AND HEAD EXTENSION 81 Min ambient working temp Max33 Extension type 8234 Ext wire nom size-type 8335 Extension/Lead length 8436 Nipple-union nom size Rating 85 ACCESSORIES37 Nipple pipe schedule no 86 Moisture seal style38 Transition type 87 Bayonet adapter size39 Termination style 8840 Connecting wire length 8941 Shield - ground wire 9042 Nipple material 9143 Union/Coupling material 92 SPECIAL REQUIREMENTS44 Coating-armor material 93 Custom tag45 Extension wire material 94 Reference specification46 Ext wire insulation matl 95 Compliance standard47 96 Construction code48 97 Calculation report49 CONNECTION HEAD 98 Calibration report50 Housing type 9951 Cover style 10052 Element conn nominal size Style 10153 Signal conn nominal size Style 102 PHYSICAL DATA54 Enclosure type no/class 103 Estimated weight55 Grounding terminal lct 104 Overall length56 Enclosure material 105 Removal clearance57 Terminal block material 106 Mfr reference dwg58 Terminal material 10759 108

110 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV LRV URV112 Temp-Output signal113 Test pressure114115116117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

Form: 20T2221 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION RTD/THERMOCOUPLE TEMPERATURE 6 SPECIFICATION IDENTIFICATIONS2 TRANSMITTER OR SWITCH 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 TRANSMITTER OR SWITCH 52 PERFORMANCE CHARACTERISTICS12 Housing type 53 Accuracy rating13 Input sensor type 54 Measurement LRL URL14 Output signal type 55 Min ambient working temp Max15 Min measurement span Max 56 Contacts ac rating At max16 Temp coef/Tolerance cl 57 Contacts dc rating At max17 Isolation type 5818 Enclosure type no/class 5919 Adjustment type 6020 Characteristic curve 6121 Digital communication std 6222 Signal power source 6323 Measurement type 6424 Configuration-no of wires 6525 Contacts arrangement Quantity 6626 Failsafe style 6727 Transient protection 68 ACCESSORIES28 Integral indicator style 69 Remote indicator style29 Signal termination type 70 Indicator enclosure30 Cert/Approval type 71 Air set filter style31 Mounting type 72 Air set gauges32 Failure/Diagnostic action 7333 Dead band type 7434 Switch time delay 75 SPECIAL REQUIREMENTS35 Temp compensation type 76 Custom tag36 Enclosure material 77 Reference specification37 Mounting kit material 78 Compliance standard38 79 Calibration report39 80 Software configuration40 8141 8242 8343 84 PHYSICAL DATA44 85 Estimated weight45 86 Overall height46 87 Removal clearance47 88 Signal conn nominal size Style48 89 Mfr reference dwg49 9050 9151 92

110 CALIBRATIONS AND TEST INPUT OR SETPOINT OUTPUT OR SCALE111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV ACTION LRV URV112 Temp- Analog output 1113 Temp-Analog output 2114 Temp-Scale115 Temp diff-Digital output116 Temp-Digital output117 Termn temp-Digital output118119 Temp setpoint 1-Output120 Temp setpoint 2-Output121 Temp setpoint 3-Output122 Temp setpoint 4-Output123124125126 COMPONENT IDENTIFICATIONS127 COMPONENT TYPE MANUFACTURER MODEL NUMBER128129130131132133Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

Form: 20T2301 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION THERMOCOUPLE ASSEMBLY 6 SPECIFICATION IDENTIFICATIONS2 w/wo THERMOWELL 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 PROTECTIVE SHEATH AND FITTING 60 THERMOWELL OR PROTECTING TUBE12 Housing type 61 Construction type13 Pad/Collar type 62 Shank style14 Fitting conn nominal size Style 63 Process conn nominal size Rating15 Mounting fitting type 64 Process conn termn type Style16 Sheath alignment 65 Internal conn nom size Style17 Sheath outside diameter Length 66 Bore diameter18 Spring loading 67 Outside dia at support19 Sheath/Braid material 68 Outside dia at tip20 Fitting material 69 Insertion length “U”21 70 Lagging extension lg “T”22 SENSING ELEMENT 71 Thermowell/Tube material23 Sensor type Quantity 72 Sheath material-thickness24 Wire nominal size 7325 Thermocouple type 7426 Tolerance class 75 PERFORMANCE CHARACTERISTICS27 Measuring junction 76 Max press at design temp At28 Thermocouple wire matl 77 Min working temperature Max29 Insulator material 78 Max fluid velocity limit At temp30 79 Temp Lower Range-Limit URL31 80 Min ambient working temp Max32 LEAD WIRE AND HEAD EXTENSION 8133 Extension type 8234 Ext wire nom size-type 8335 Extension/Lead length 84 ACCESSORIES36 Nipple-union nom size Rating 85 Moisture seal style37 Nipple pipe sched no 86 Bayonet adapter size38 Transition type 8739 Termination style 8840 Connecting wire length 8941 Shield - ground wire 9042 Nipple material 91 SPECIAL REQUIREMENTS43 Union/Coupling material 92 Custom tag44 Coating-armor material 93 Reference specification45 Extension wire material 94 Compliance standard46 Ext wire insulation matl 95 Construction code47 96 Calculation report48 97 Calibration report49 CONNECTION HEAD 9850 Housing type 9951 Cover style 10052 Element conn nominal size Style 101 PHYSICAL DATA53 Signal conn nominal size Style 102 Estimated weight54 Enclosure type no/class 103 Overall length55 Grounding terminal lct 104 Removal clearance56 Enclosure material 105 Mfr reference dwg57 Terminal block material 10658 Terminal material 10759 108

110 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV LRV URV112 Temp-Output signal113 Test pressure114115116117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER120121122123124125Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

Form: 20T2401 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION THERMAL RADIATION TEMPERATURE 6 SPECIFICATION IDENTIFICATIONS2 SENSOR w/wo MONITOR 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 SENSING ELEMENT 60 MONITOR Continued12 Sensor type 61 Failure/Diagnostic action13 Temperature LRL URL 62 Enclosure material14 Spectral response 6315 Focus type 6416 65 PERFORMANCE CHARACTERISTICS17 66 Min head working temp Max18 HEAD AND VIEWER 67 Temp accuracy rating19 Head type 68 Focus point D:S ratio20 Housing style 69 Far point D:S ratio21 Enclosure type no/class 70 Min monitor amb working Max22 Sighting type 71 Contacts ac rating At max23 Lens purge style 72 Contacts dc rating At max24 Conn adapter type 7325 Cable length 7426 Signal termination type 7527 Cert/Approval type 7628 Mounting type 7729 Enclosure material 7830 7931 8032 TRANSMITTER OR MULTIPLEXER 8133 Type 8234 Signal selector type 8335 Cable length 84 ACCESSORIES36 Output signal type 85 Blast gate style37 Enclosure type no/class 86 Cooling flow regulator38 Signal power source 87 Sight tube material39 Adjustment type 88 Printer40 Number input sensors 8941 9042 MONITOR 91 SPECIAL REQUIREMENTS43 Housing type 92 Custom tag44 External input type 93 Reference specification45 Output signal type 94 Compliance standard46 Zero-span adjustment lct 95 Calibration report47 Enclosure type no/class 96 Software configuration48 Measurement type 9749 Digital communication std 9850 Signal power source 9951 Dead band type 100 PHYSICAL DATA52 Contacts arrangement Quantity 101 Estimated weight53 Emissivity adjustment 102 Overall height54 Failsafe style 103 Removal clearance55 Integral indicator style 104 Signal conn nominal size Style56 Signal termination type 105 Mfr reference dwg57 Cert/Approval type 10658 Mounting type 10759 Temperature compensation 108

110 CALIBRATIONS AND TEST INPUT OR SETPOINT OUTPUT OR SCALE111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/SCALE LRV URV ACTION LRV URV112 Temp-Analog output 1113 Temp-Analog output 2114 Temp-Analog output 3115 Temperature-Scale116 Temp setpoint 1-Output117 Temp setpoint 2-Output118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125




--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

Form: 20T2501 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION THERMOWELL OR PROTECTING TUBE 6 SPECIFICATION IDENTIFICATIONS2 ASSEMBLY 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 OPERATING PARAMETERS 60 CONNECTION HEAD continued12 Project number Sub project no 61 Element conn nominal size Style13 Project 62 Signal conn nominal size Style14 Enterprise 63 Enclosure type no/class15 Site 64 Grounding terminal lct16 Area Cell Unit 65 Enclosure material17 Related equipment 66 Terminal block material18 Service 67 Terminal material19 6820 P&ID/Reference dwg number 6921 Material name 7022 Maximum pressure 71 PERFORMANCE CHARACTERISTICS23 Minimum temperature 72 Max press at design temp At24 Normal temperature 73 Min working temperature Max25 Maximum temperature 74 Max fluid velocity limit At temp26 Material phase 7527 Maximum fluid velocity 7628 7729 7830 THERMOWELL OR PROTECTING TUBE 7931 Construction type 8032 Shank style 8133 Process conn nominal size Rating 8234 Process conn termn type Style 8335 Internal conn nom size Style 8436 Cap/Plug style 8537 Bore diameter 86 ACCESSORIES38 Outside dia at support 8739 Outside diameter at tip 8840 Insertion length “U” 8941 Lagging extension lg “T” 9042 Thermowell/Tube material 9143 Sheath material-thickness 92 SPECIAL REQUIREMENTS44 Cap/Plug material 93 Custom tag45 94 Reference specification46 95 Compliance standard47 EXTENSION ASSEMBLY 96 Construction code48 Extension type 97 Calculation report49 Extension length 9850 Nipple-union nom size Rating 9951 Nipple pipe schedule no 10052 Nipple material 101 PHYSICAL DATA53 Union/Coupling material 102 Estimated weight54 103 Overall length55 104 Removal clearance56 105 Mfr reference dwg57 CONNECTION HEAD 10658 Housing type 10759 Cover style 108

110 CALIBRATIONS AND TEST TEST111 TAG NO/FUNCTIONAL IDENT TEST URV112 Test pressure113114115116117118 COMPONENT IDENTIFICATIONS119 COMPONENT TYPE MANUFACTURER MODEL NUMBER120121122123124125Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

1 RESPONSIBLE ORGANIZATION LOAD CELL OR TRANSDUCER 6 SPECIFICATION IDENTIFICATIONS2 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 BODY OR HOUSING 58 SUMMING UNIT OR JUNCTION BOX12 Body/Housing type 59 Configuration type13 Construction style 60 Enclosure type no/class14 Load conn/thru-hole size 61 Max Input signal quantity15 Load conn termn type Style 62 Cert/Approval type16 Load button 63 Mounting location/type17 Body/Housing material 64 Enclosure material18 Seal/O ring material 6519 6620 67 PERFORMANCE CHARACTERISTICS21 SENSING ELEMENT 68 Min working temperature Max22 Force sensor type 69 Accuracy rating Ref23 Construction style 70 Linearity Ref24 Rated capacity/stress 71 Repeatability Ref25 Rated nominal output 72 Temp compensation LRL URL26 Nominal resistance 73 Overrange limit Ref27 74 Temp effect on zero Ref28 75 Temp effect on span Ref29 SIGNAL OR AMPLIFIER 76 Life cycles30 Configuration type 7731 Output signal type 7832 Enclosure type no/class 7933 Local adjustment type 80 ACCESSORIES34 Signal termination type 81 Simulated component35 Supply/Excitation voltage 82 Mating connector36 Cert/Approval type 83 Access ramp37 Mounting location/type 84 Pit frame38 Remote enclosure material 8539 8640 8741 LEAD WIRE AND EXTENSION 88 SPECIAL REQUIREMENTS42 Extension type 89 Custom tag43 Conductor nominal size 90 Reference specification44 Cable length 91 Compliance standard45 Connector configuration 92 Calibration report46 Signal termination type 9347 Cable jacket material 9448 9549 96 PHYSICAL DATA 50 MOUNTING HARDWARE 97 Estimated weight51 Hardware type 98 Overall length52 Construction style 99 Overall height53 Surface finish 100 Outside diameter/Width54 Hardware material 101 Signal conn nominal size Style55 Isolation pad material 102 Mfr reference dwg56 10357 104

110 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/SCALE LRV URV LRV URV112 Weight 1-Output signal113 Weight 2-Output signal114 Weight 3-Output signal115 Weight 4-Output signal116 Weight 5-Output signal117 Weight 6-Output signal118 Weight 7-Output signal119 Weight 8-Output signal120 Weight sum-Output signal121122 COMPONENT IDENTIFICATIONS123 COMPONENT TYPE MANUFACTURER MODEL NUMBER124125126127Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS

Form: 20W2211 Rev 0 © 2004 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

1 RESPONSIBLE ORGANIZATION ELECTRONIC WEIGHT TRANSMITTER 6 SPECIFICATION IDENTIFICATIONS2 INDICATOR OR CONTROLLER 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 OPERATING PARAMETERS 53 PERFORMANCE CHARACTERISTICS12 Project number Sub project no 54 Linearity Ref13 Project 55 Repeatability Ref14 Enterprise 56 Max input signal15 Site 57 Max Resolution16 Area Cell Unit 58 Sensitivity Ref17 Related equipment 59 Max response time18 Service 60 Min ambient working temp Max19 61 Contacts ac rating At max20 P&ID/Reference dwg number 62 Contacts dc rating At max21 Remote hazardous area cl Div/Zone Group 63 Max sensor to receiver lg22 Remote area min ign temp Temp ident number 6423 6524 6625 TRANSMITTER OR INDICATOR OR CONTROLLER 6726 Housing type 68 ACCESSORIES27 Interface style 69 Remote indicator style28 Input sensor/signal type 70 Remote indicator mounting29 Input excitation style 71 Remote indicator enclosure30 Output signal type 72 Calibrator style31 Analog output resolution 7332 Enclosure type no/class 7433 Control mode 7534 Local operator interface 76 SPECIAL REQUIREMENTS35 Characteristic curve 77 Custom tag36 Digital communication std 78 Reference specification37 Signal power source 79 Compliance standard38 Aux input signal type 80 Software configuration39 Max qty sensor/xdcr/xmtr 81 Software program40 Signal summing circuit 8241 Contacts arrangement Quantity 8342 Integral indicator style 8443 Display resolution 85 PHYSICAL DATA 44 Cert/Approval type 86 Estimated weight45 Mounting location/type 87 Overall width46 Failure/Diagnostic action 88 Overall height47 Transducer diagnostics 89 Overall depth48 Signal filtration 90 Signal conn nominal size Style49 Transducer calibration 91 Mfr reference dwg50 Enclosure material 9251 9352 94

110 CALIBRATIONS AND TEST INPUT OR TEST OUTPUT OR SCALE111 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/SCALE LRV URV ACTION LRV URV112 Weight-Analog output 1113 Weight-Analog output 2114 Weight-Digital output115 Weight-Scale 1116 Weight-Scale 2117 Weight setpoint 1-Output118 Weight setpoint 2-Output119 Weight setpoint 3-Output120 Weight setpoint 4-Output121 Weight setpoint 5-Output122 Weight setpoint 6-Output123 Weight setpoint 7-Output124 Weight setpoint 8-Output125 Failure signal-Output126127 COMPONENT IDENTIFICATIONS128 COMPONENT TYPE MANUFACTURER MODEL NUMBER129130131132Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS

Form: 20W2221 Rev 0 © 2004 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

1 RESPONSIBLE ORGANIZATION FIELDBUS JUNCTION 6 SPECIFICATION IDENTIFICATIONS 2 7 Document no 3 Device Specification 8 Latest revision Date4 9 Issue status 5 10

11 OPERATING PARAMETERS 46 PERFORMANCE CHARACTERISTICS 12 Project number Sub project no 47 Min ambient working temp Max13 Project 48 Maximum input voltage 14 Enterprise 49 Current consumption 15 Site 50 Max current rating16 Hazardous area cl Div/Zone Group 51 Current limiting17 Area min ign temp Temp ident number 52 18 53 19 54 20 JUNCTION DEVICE 55 21 Housing type 56 22 Construction style 57 23 Trunk conn nominal size 58 24 Trunk connection type 59 ACCESSORIES 25 Trunk connection style 60 External terminator26 Spur conn nominal size 61 Mounting hardware 27 Spur connection type 62 Special enclosure 28 Spur connection style 63 Connector cover/cap29 Circuit protection style 64 Connector lock 30 Enclosure type no/class 6531 Digital communication std 6632 Conductor cabling type 67 SPECIAL REQUIREMENTS33 Spur/Drop quantity 68 Custom tag34 Grounding configuration 69 Reference specification 35 Integral indicator style 70 Compliance standard 36 Signal termination type 7137 Cert/Approval type 7238 Mounting type 73 PHYSICAL DATA 39 Terminator location 74 Estimated weight 40 Transient protection 75 Overall width 41 Enclosure material 76 Overall height 42 Trunk conn/Gland matl 77 Overall depth 43 Spur conn/Gland matl 78 Mfr reference dwg44 7945 8081 TAG NUMBER Area Cell Unit 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99

100 101 102 103 COMPONENT IDENTIFICATIONS 104 COMPONENT TYPE MANUFACTURER MODEL NUMBER 105 106 107 108 109 110 Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS

Form: 20Y2511 Rev 0 © 2005 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

1 RESPONSIBLE ORGANIZATION FIELDBUS JUNCTION 6 SPECIFICATION IDENTIFICATIONS 2 7 Document no 3 Device Specification 8 Latest revision Date4 Tag Number List Continued 9 Issue status 5 10

11 TAG NUMBER Area Cell Unit 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS

Form: 20Y2512 Rev 0 © 2005 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

1 RESPONSIBLE ORGANIZATION ELECTROMECHANICAL LIMIT SWITCH 6 SPECIFICATION IDENTIFICATIONS2 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 OPERATING PARAMETERS 64 SWITCH MECHANISM Continued12 Project number Sub project no 65 Integral indicator style13 Project 66 Signal termination type14 Enterprise 67 Cert/Approval type15 Site 68 Time delay type16 Area Cell Unit 69 Contact material17 Related equipment 7018 7119

Service72 LEAD WIRE AND EXTENSION

20 P&ID/Reference dwg number 73 Extension type21 Inline hazardous area cl Div/Zone Group 74 Conductor nominal size22 Inline area min ign temp Temp ident number 75 Cable length23 Minimum temperature 76 Connector configuration24 Maximum temperature 77 Signal termination type25 Min required overtravel 78 Cable jacket material26 Maximum travel to operate 7927 Actuating material 8028 81 PERFORMANCE CHARACTERISTICS29 82 Operating force/torque30 83 Repeatability Ref31 SWITCH HOUSING 84 Max over travel limit32 Housing type 85 Max travel to reset33 Construction style 86 Min ambient working temp Max34 Nominal size 87 Contacts ac rating At max35 Enclosure type no/class 88 Contacts dc rating At max36 Mounting location/type 89 Mechanical life cycles37 Housing material 90 Electrical life cycles38 9139 9240 ACTUATOR 9341 Actuator type 94 ACCESSORIES42 Actuator style 95 Mating connector43 Free position LRL URL 96 Mounting adaptor/base44 Pre-Travel to operate 9745 Total travel 9846 Operator type 9947 Movement operation mode 100 SPECIAL REQUIREMENTS48 Lever nominal size 101 Custom tag49 Mounting orientation 102 Reference specification50 Lever arm material 103 Compliance standard51 Roller/Rod material 10452 Seal material 10553 10654 107 PHYSICAL DATA55 SWITCH MECHANISM 108 Estimated weight56 Switch type 109 Overall width57 Contact style 110 Overall length/height58 Nominal contact rating 111 Overall depth59 Output signal type 112 Signal conn nominal size Style60 Switch action type 113 Mfr reference dwg61 Digital communication std 11462 Circuitry type 11563 Contact arrangement Quantity 116

117 CALIBRATIONS AND TEST INPUT OR SETPOINT OUTPUT118 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV ACTION LRV URV119 Setpoint 1-Output120 Setpoint 2-Output121 Position-Analog output122123 COMPONENT IDENTIFICATIONS124 COMPONENT TYPE MANUFACTURER MODEL NUMBER125126127128Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS

Form: 20Z2011 Rev 0 © 2004 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

1 RESPONSIBLE ORGANIZATION PROXIMITY SENSOR 6 SPECIFICATION IDENTIFICATIONS2 7 Document no3 Device Specification 8 Latest revision Date4 9 Issue status5 10

11 OPERATING PARAMETERS 64 SWITCH MECHANISM Continued12 Project number Sub project no 65 False pulse protection13 Project 66 Transient protection14 Enterprise 6715 Site 6816 Area Cell Unit 69 LEAD WIRE AND EXTENSION17 Related equipment 70 Extension type18 Service 71 Conductor nominal size19 72 Cable length20 P&ID/Reference dwg number 73 Connector configuration21 Inline hazardous area cl Div/Zone Group 74 Signal termination type22 Inline area min ign temp Temp ident number 75 Cable jacket material23 Minimum temperature 7624 Maximum temperature 7725 Minimum target position 78 PERFORMANCE CHARACTERISTICS26 Maximum target position 79 Min operating voltage Max27 Target material 80 Repeatability Ref28 81 Overload trigger29 82 Short circuit trigger30 83 Weld field immunity At31 SWITCH HOUSING 84 Min ambient working temp Max32 Housing type 85 Minimum load current33 Construction style 86 Contacts ac rating At max34 Nominal size 87 Contacts dc rating At max35 Enclosure type no/class 88 Max leakage current At36 Mounting location/type 8937 Housing material 9038 9139 92 ACCESSORIES40 SENSING ELEMENT 93 Mating connector41 Sensing type 94 Mounting adaptor42 Sensor style 95 Mounting bracket43 Switching frequency 96 Magnetic actuator44 Nom/max sensing distance 9745 Shielding style 9846 Barrel diameter 9947 Probe insertion length 100 SPECIAL REQUIREMENTS48 Mounting orientation 101 Custom tag49 Casing material 102 Reference specification50 Active face material 103 Compliance standard51 10452 10553 SWITCH MECHANISM 10654 Switch type 107 PHYSICAL DATA 55 Output signal type 108 Estimated weight56 Digital communication std 109 Overall width57 Contact arrangement Quantity 110 Overall length/height58 Load switching style 111 Overall depth59 Integral indicator style 112 Threaded length60 Signal termination type 113 Signal conn nominal size Style61 Cert/Approval type 114 Mfr reference dwg62 Field immunity style 11563 Polarity protection 116

117 CALIBRATIONS AND TEST INPUT OR SETPOINT OUTPUT118 TAG NO/FUNCTIONAL IDENT MEAS/SIGNAL/TEST LRV URV ACTION LRV URV119 Setpoint 1-Output120 Setpoint 2-Output121 Presence-Analog output122123 COMPONENT IDENTIFICATIONS124 COMPONENT TYPE MANUFACTURER MODEL NUMBER125126127128Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS

Form: 20Z2012 Rev 0 © 2004 ISA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

Form: 20G3001 Rev 0 © 2001 ISA

1 RESPONSIBLE ORGANIZATION GENERAL OR SPECIAL 6 SPECIFICATION IDENTIFICATIONS2 REQUIREMENTS 7 Doc no3 8 Latest rev Date4 9 Issue status5 10

11 These general or special requirements shall be considered as part of the requirements for the equipment covered by the individual12 requisition and/or specification sheets.13 Table of Contents14 Requirements Page15161718

192021222324252627282930313233343536376566676869707172737475767778798081828384858687888990919293949596979899

100101102Rev Date Revision Description By Appv1 Appv2 Appv3 REMARKS



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\




--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

– 117 – ISA–TR20.00.01–2007

Annex C (informative) – Specification forms pick list andcontextual help references

This annex is included for informational purposes and is not part of this Technical Report.

Due to the large size of the pick list files for all of the approved forms, they are not attached to thisTechnical Report. The latest versions of the pick lists may be viewed and downloaded for free from the ISAwebsite at www.isa.org/standards.



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\




--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

Developing and promulgating sound consensus standards, recommended practices, and technical reports is one of ISA’s primary goals. To achieve this goal the Standards and Practices Department relies on the technical expertise and efforts of volunteer committee members, chairmen and reviewers.

ISA is an American National Standards Institute (ANSI) accredited organization. ISA administers United States Technical Advisory Groups (USTAGs) and provides secretariat support for International Electrotechnical Commission (IEC) and International Organization for Standardization (ISO) committees that develop process measurement and control standards. To obtain additional information on the Society’s standards program, please write:

ISA Attn: Standards Department 67 Alexander Drive P.O. Box 12277 Research Triangle Park, NC 27709

ISBN 10: 1-55617-754-2 ISBN 13: 978-1-55617-754-5



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

Specification Forms forProcess Measurement andControl InstrumentsPart 3: Form Requirementsand Development Guidelines

Approved 04 April 2001

ISA–20.00.03–2001

S T A N D A R D

ISA The Instrumentation,Systems, and

Automation Society

–TM



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

ISA–20.00.03–2001Specification Forms for Process Measurement and Control InstrumentsPart 3: Form Requirements and Development Guidelines

ISBN: 1-55617-755-0

Copyright © 2001 by ISA–The Instrumentation, Systems, and Automation Society. All rights reserved. Notfor resale. Printed in the United States of America. No part of this publication may be reproduced, stored ina retrieval system, or transmitted, in any form or by any means (electronic, mechanical, photocopying,recording, or otherwise), without the prior written permission of the Publisher.

ISA67 Alexander DriveP. O. Box 12277Research Triangle Park, North Carolina 27709USA



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

– 3 – ISA–20.00.03–2001

Preface

This preface, as well as all footnotes and annexes, is included for information purposes and is not part ofISA–20.00.03–2001.

The standards referenced within this document may contain provisions that, through reference in this text,constitute requirements of this document. At the time of publication, the editions indicated were valid. Allstandards are subject to revision, and parties to agreements based on this document are encouraged toinvestigate the possibility of applying the most recent editions of the standards indicated within thisdocument. Members of IEC and ISO maintain registers of currently valid International Standards. ANSImaintain registers of currently valid U.S. National Standards.

This document has been prepared as part of the service of ISA–The Instrumentation, Systems, andAutomation Society, toward a goal of uniformity in the field of instrumentation. To be of real value, thisdocument should not be static but should be subject to periodic review. Toward this end, the Societywelcomes all comments and criticisms and asks that they be addressed to the Secretary, Standards andPractices Board; ISA; 67 Alexander Drive; P. O. Box 12277; Research Triangle Park, NC 27709;Telephone (919) 549-8411; Fax (919) 549-8288; E-mail: [email protected].

The ISA Standards and Practices Department is aware of the growing need for attention to the metricsystem of units in general, and the International System of Units (SI) in particular, in the preparation ofinstrumentation standards. The Department is further aware of the benefits to USA users of ISA standardsof incorporating suitable references to the SI (and the metric system) in their business and professionaldealings with other countries. Toward this end, this Department will endeavor to introduce SI-acceptablemetric units in all new and revised standards, recommended practices, and technical reports to thegreatest extent possible. Standard for Use of the International System of Units (SI): The Modern MetricSystem, published by the American Society for Testing & Materials as IEEE/ASTM SI 10-97, and futurerevisions, will be the reference guide for definitions, symbols, abbreviations, and conversion factors.

It is the policy of ISA to encourage and welcome the participation of all concerned individuals and interestsin the development of ISA standards, recommended practices, and technical reports. Participation in theISA standards-making process by an individual in no way constitutes endorsement by the employer of thatindividual, of ISA, or of any of the standards, recommended practices, and technical reports that ISAdevelops.

CAUTION — ISA ADHERES TO THE POLICY OF THE AMERICAN NATIONAL STANDARDSINSTITUTE WITH REGARD TO PATENTS. IF ISA IS INFORMED OF AN EXISTING PATENT THAT ISREQUIRED FOR USE OF THE STANDARD, IT WILL REQUIRE THE OWNER OF THE PATENT TOEITHER GRANT A ROYALTY-FREE LICENSE FOR USE OF THE PATENT BY USERS COMPLYINGWITH THE STANDARD OR A LICENSE ON REASONABLE TERMS AND CONDITIONS THAT AREFREE FROM UNFAIR DISCRIMINATION.

EVEN IF ISA IS UNAWARE OF ANY PATENT COVERING THIS STANDARD, THE USER ISCAUTIONED THAT IMPLEMENTATION OF THE STANDARD MAY REQUIRE USE OF TECHNIQUES,PROCESSES, OR MATERIALS COVERED BY PATENT RIGHTS. ISA TAKES NO POSITION ON THEEXISTENCE OR VALIDITY OF ANY PATENT RIGHTS THAT MAY BE INVOLVED IN IMPLEMENTINGTHE STANDARD. ISA IS NOT RESPONSIBLE FOR IDENTIFYING ALL PATENTS THAT MAYREQUIRE A LICENSE BEFORE IMPLEMENTATION OF THE STANDARD OR FOR INVESTIGATINGTHE VALIDITY OR SCOPE OF ANY PATENTS BROUGHT TO ITS ATTENTION. THE USER SHOULDCAREFULLY INVESTIGATE RELEVANT PATENTS BEFORE USING THE STANDARD FOR THEUSER’S INTENDED APPLICATION.



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

ISA–20.00.03–2001 – 4 –

HOWEVER, ISA ASKS THAT ANYONE REVIEWING THIS STANDARD WHO IS AWARE OF ANYPATENTS THAT MAY IMPACT IMPLEMENTATION OF THE STANDARD NOTIFY THE ISASTANDARDS AND PRACTICES DEPARTMENT OF THE PATENT AND ITS OWNER.

ADDITIONALLY, THE USE OF THIS STANDARD MAY INVOLVE HAZARDOUS MATERIALS,OPERATIONS OR EQUIPMENT. THE STANDARD CANNOT ANTICIPATE ALL POSSIBLEAPPLICATIONS OR ADDRESS ALL POSSIBLE SAFETY ISSUES ASSOCIATED WITH USE INHAZARDOUS CONDITIONS. THE USER OF THIS STANDARD MUST EXERCISE SOUNDPROFESSIONAL JUDGMENT CONCERNING ITS USE AND APPLICABILITY UNDER THE USER’SPARTICULAR CIRCUMSTANCES. THE USER MUST ALSO CONSIDER THE APPLICABILITY OFANY GOVERNMENTAL REGULATORY LIMITATIONS AND ESTABLISHED SAFETY AND HEALTHPRACTICES BEFORE IMPLEMENTING THIS STANDARD.

The following people served as members of ISA Committee SP20:

NAME COMPANY

G. Barta, Chairman Bechtel Corp.W. Albe Dow Corning Corp.S. Alvarez Compania Inspeccion MexicanaT. Baldwin Brown & Root, Inc.N. Battikha Bergo Tech, Inc.E. Berger Mitre Corp.J. Carew ConsultantT. Caston Eastman Chemicals Co.B. Cleary Rosemount, Inc.K. Cole Burns & Roe EnterprisesE. Crawford Nova Control Systems, Inc.T. D. Daniel ConsultantA. Engels Praxair, Inc.G. Erk ConsultantF. Ford Bayer Corp.G. Gifford FlowserveR. Gulley Vara InternationalR. Hartman Fisher-Rosemount Systems, Inc.C. Hill Brown & Root, Inc.H. Hinssen Exxon Chemical EngineeringW. Ingham Stantec Consulting Ltd.A. Iverson Ivy OptiksD. Kelly VECO Rocky Mountain, Inc.H. Koning DSM ServicesM. Kulkarni General Instruments ConsortiumT. McAvinew Merrick & Co.A. McCauley Chagrin Valley Controls, Inc.J. McQuighan Constellation EnergyJ. Meppen Y. Meppen ConsultantsD. Osborn Greeley & HansenC. Phillips Technip USA Corp.G. Ramachandran Cytec Industries, Inc.G. Richardson Thermco Instrument Corp.J. Rourke Jacobs Engineering GroupP. Rowland SOIGNE Associates, Inc.G. Sanders Penberthy, Inc.M. Scott Process Measurement Tech. Ltd.



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

– 5 – ISA–20.00.03–2001

J. Sen Bechtel Corp.R. Shah ConsultantJ. Soos Huntsman Corp.M. Spencer Desktop Engineering Ltd.J. Summerfield ConsultantR. Sundar Foster Wheeler USA Corp.L. Takeyasu Kenonic Controls, Inc.D. Taylor Spartan ControlsR. Town Jefferson Services Co, Inc.I. Verhappen Syncrude Canada Ltd.E. Welch Duke/Fluor Daniel, Inc.B. Williams Merck & Co. Inc.

This standard was approved for publication by the ISA Standards and Practices Board on04 April 2001.

NAME COMPANY

M. Zielinski Fisher-Rosemount Systems, Inc.D. Bishop ConsultantM. Cohen ConsultantM. Coppler Ametek, Inc.B. Dumortier Schneider ElectricW. Holland Southern CompanyE. Icayan Advanced Control & Engineering SolutionsA. Iverson Ivy OptiksR. Jones Dow Chemical Co.V. Maggioli Feltronics Corp.T. McAvinew Merrick & Co.A. McCauley, Jr. Chagrin Valley Controls, Inc.G. McFarland Westinghouse Process Control Inc.D. Rapley Rapley Consulting Inc.R. Reimer Rockwell AutomationJ. Rennie Factory Mutual Research Corp.H. Sasajima Yamatake Corp.I. Verhappen Syncrude Canada Ltd.R. Webb Power EngineersW. Weidman Parsons Energy & Chemicals GroupJ. Weiss EPRIM. Widmeyer EG&G Defense MaterialsR. Wiegle CANUS Corp.C. Williams Eastman Kodak Co.G. Wood Graeme Wood Consulting



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\




--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

– 7 – ISA–20.00.03–2001

Contents

1 Scope................................................................................................................................................... 13

2 Normative references........................................................................................................................... 13

3 Definitions ............................................................................................................................................ 13

4 Application ........................................................................................................................................... 13

5 Requirements and optional information ............................................................................................... 14

5.1 Form types, content, and order..................................................................................................... 14

5.2 Form formats ................................................................................................................................ 21

5.3 Form terminology.......................................................................................................................... 22

5.4 Data field content.......................................................................................................................... 22

6 Preparation of new specification forms ................................................................................................ 22

6.1 Reference sources........................................................................................................................ 23

6.2 Review and modification of Operating Parameters forms ............................................................ 23

6.3 Development guidelines for Device Specification forms............................................................... 23

6.4 Contextual help instructions.......................................................................................................... 24

6.5 Pick list.......................................................................................................................................... 24

6.6 Data dictionary update.................................................................................................................. 25

6.7 Review and approval .................................................................................................................... 25

7 Classification and designation.............................................................................................................. 25

Annex A (informative) — References.......................................................................................................... 27



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\




--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

– 9 – ISA–20.00.03–2001

Foreword

This standard has been prepared by ISA’s SP20 standards committee, Instrument Specification Forms.The ISA–SP20 committee welcomes comments and suggestions, and requests that they be addressed tothe Chairperson, ISA-SP20, ISA, 67 Alexander Drive, Research Triangle Park, NC 27709 USA.

This standard modifies the form style of the previous ISA-20-1981 to provide a dedicated page foroperating parameters, and expands the form content beyond the limitations of ISA-20-1981.

This standard applies to all processes of development and use of specification forms for processmeasurement and control instruments. Specifically, it provides requirements and guidance for thedevelopment of new or revised forms.

The other parts of this series, Specification Forms for Process Measurement and Control Instruments, are asfollows:

ISA–TR20.00.01–2001 Part 1: General Considerations

ISA Draft 20.00.02 Part 2: Instructions for Using Specification Forms

ISA Draft TR20.00.04 Part 4: Data Dictionary



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\




--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

– 11 – ISA–20.00.03–2001

Introduction

Specification forms developed by ISA’s SP20 committee are designed to facilitate communication betweeninstrument specifiers and manufacturers in the exchange of data on standard commercially availableinstrument devices. They are not intended to be used as a hardware design specification. New devicesand options for existing devices continually enter the market and may justify the creation or modification ofspecification forms.

The following are the purposes of these specification form requirements and development guidelines:

a) To minimize the effort and duration required to develop and review new forms for ISA approval

b) To promote uniformity within a form and between forms in content, format, terminology, and maximumfield prompt lengths

c) To promote uniformity between form parts by identifying content criteria for operating parameters anddevice properties

d) To assist in the preparation of a complete specification form by identifying device properties thatcorrelate with the operating parameters

e) To provide guidance to develop instrument specification forms, field prompt contextual helpinstructions, and pick lists



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\




--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

– 13 – ISA–20.00.03–2001

1 Scope

This standard establishes requirements for instrument specification forms to be published by ISA. Its use isrecommended for organizations that develop their own equivalent specification forms.

The guidelines set forth in this standard will assist in the efficient production of specification forms thatmaintain consistency and compatibility with ISA specification forms.

2 Normative references

No normative references are required in using this standard. For a list of informative references, seeannex A.

3 Definitions

For the purposes of this standard, the following definitions apply.

3.1 contextual help:explanation of the field prompt or desired data entry field response.

3.2 data entry field:the specification form area into which data are entered.

3.3 field prompt:the descriptive text on the specification form that identifies the data entry field.

3.4 main device:the fundamental or most important measurement or control device of a composite assembly that containssecondary devices or accessories.

3.5 pick list:a list of example or preferred enumerated choices for a data entry field.

4 Application

Members of standards committees, users or manufacturers, and experts can use their knowledge ofparticular instrument hardware and this standard to develop new specification forms, provide contextualhelp instructions, and develop pick lists for filling out the forms.

These form requirements and development guidelines may be used for the following:

a) To evaluate the adequacy of an existing Operating Parameters specification form for specifying a newhardware device (as per ISA–TR20.00.01–2001)

b) To develop new instrument Device Specification forms (as per ISA–TR20.00.01–2001)

c) To establish review criteria for new or revised forms seeking approval



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

ISA–20.00.03–2001 – 14 –

5 Requirements and optional information

5.1 Form types, content, and order

5.1.1 Three form types

The specification forms are generally comprised of three form types for the following informationorganization:

a) Operating Parameters forms are developed to communicate the process variables, operatingconditions, process design conditions, component design criteria, material properties, and operatingenvironment conditions of a device’s application.

b) Device Specification forms are developed to communicate hardware device requirements andproperties for a main device and for attached and directly associated devices.

c) The General or Special Requirements form has been developed to communicate the Table ofContents for general or special requirements that are applicable to the device, but that need additionalspace beyond that available in the other two types of forms.

5.1.2 Content of Operating Parameters forms

Operating Parameters forms are developed to identify the process variables to be measured or controlled,and the related process and environmental parameters that affect the measurement or control objectives.A single form is appropriate for all instrument device types that relate to the identified commonmeasurement variable or final control element.

The following information categories are required for these forms, if appropriate for the device type:

a) Administrative identifications

b) Service identifications

c) Component design criteria

d) Material flow condition variables that are necessary to perform sizing calculations or device typeselection

e) Process design conditions that are necessary for device type selection

f) Material name, composition, and properties required for calculations, device sizing, or suitabilityevaluation

g) Environmental operating conditions

h) Physical installation data that are required to evaluate the device application.

Optional parameters that should be evaluated for inclusion on an Operating Parameters form, or on asupplemental page of the form, include the following:

a) Special requirements for the application or hardware device

b) Preliminary sizing analysis calculation results that are pertinent to sizing or device type selection



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

– 15 – ISA–20.00.03–2001

c) Basic engineering design data that identify the environmental and service parameters that the devicemust operate within

d) Detailed material composition data

5.1.3 Content of Device Specification forms

Device Specification forms are developed to encompass the information required that defines the physicalinstrument device and the requirements for its immediately associated secondary devices. The secondarydevice properties may be developed on a supplemental form page.

The specific content of any specification form should primarily be dependent only upon the characteristicsof the device that are necessary for communication between the specifier and the manufacturer. Theintended use of the specification form, such as a document for preliminary inquiry and quotation, atraditional specification, or a conforming specification, can affect how much of the form content is requiredto be used to accomplish the respective objectives.

The general criteria for including a property on a device specification form include the following.

5.1.3.1 Type and style field prompts

Each subsection of the form should start with a “type” field intended to clarify the major classification ofthat device component. A “style” field is sometimes additionally advantageous to classify componentconstruction.

5.1.3.2 Compliance verification field prompts

Correlated parameter field prompts are required that provide confirmation that the device propertiescomply with the operating parameter limits that are identified in the specification. Typical field promptcategories that must be considered for inclusion are shown in table 1.

Table 1 — Correlated parameters

Operating Parameters form field category Device Specification form field category

Component design criteria Performance characteristics

Process design conditions Design ratings

Measured variable range Measurement range limits

Calculated operating variables Working limits

Piping termination properties Termination properties

Piping materials Materials of construction

5.1.3.3 Model designation field prompts

Device manufacturers’ literature generally states their required data for ordering. Field prompts arerequired to cover those properties by explicitly identifying each of the device attributes that are so identifiedor used to generate the model number. These field prompts will generally include the following types ofproperties:

a) Model series that identifies the device type or style



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

ISA–20.00.03–2001 – 16 –

b) Nominal size

c) Process connection nominal size, category, type, and rating

d) Measurement span and range limits

e) Calibration or adjustment values

f) Control action

g) Signal power source

h) Output signal type and range limits

i) Standard design optional features

j) Material of construction for pressure boundary components

k) Major material of construction for internal wetted components

l) Mounting type or configuration

m) Enclosure classification

n) Standard optional accessories

o) Safety certifications, listings, or approvals

5.1.3.4 User-definable fields

Blank field prompts shall be provided in each form subsection to accommodate specifying of the lesscommon device properties.

5.1.3.5 Optional performance characteristics field prompts

Design and device selection reviews often require some device performance characteristics to be providedby the manufacturer in addition to those covered in table 1.

5.1.3.6 Optional construction design alternatives field prompts

Manufacturers are often given responsibility to select device construction alternatives that should ultimatelybe reviewed for acceptability by the specifier. Those properties that are generally desirable to solicit anddocument within the specification form include the following:

a) Enclosure ratings

b) Standard material of construction for pressure boundary components not covered in the basic modelnumber

c) Standard material of construction for wetted components not covered in the basic model number

d) Standard accessories recommended for the service application

e) Optional construction styles or features recommended for the service application



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

– 17 – ISA–20.00.03–2001

5.1.3.7 Optional special requirements field prompts

Properties for frequently specified special requirements are desirable, such as the following:

a) Tag or nameplates

b) Preparations

c) Construction code or standard

d) Calibration or inspection reports

5.1.3.8 Optional physical data field prompts

Design and device selection reviews often require some basic device physical data that are advantageousto incorporate in the specification form data, such as the following:

a) Estimated weight

b) Major dimensions

c) Manufacturers' dimensional reference drawing

5.1.3.9 Optional calibrations and tests data field prompts

Documentation of device properties that are used during a maintenance check or replacement is desirable,such as the following:

a) Bench set limits

b) Rated travel

c) Test conditions

5.1.4 Subsection order of Device Specification forms

The properties of instrument devices, and their associated secondary devices, have been data modeled tofacilitate consistency of presentation between the properties of devices and between specification forms.The specification form should select the appropriate generic property groupings, and arrange therespective specific subsections in the following recommended order:

a) Pressure-containing shell properties

b) Pressure-containing shell extension component properties

c) Internal subcomponent properties

d) Signal input/output extension component properties

e) Integral input/output component properties

f) Auxiliary devices properties

g) Performance characteristic properties



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

ISA–20.00.03–2001 – 18 –

h) Accessories properties

i) Special requirements

j) Physical data properties

k) Calibrations and tests properties

l) Component identifications

5.1.5 Subsection content order of Device Specification forms

The following field prompt order shall be used (as applicable) within any subsection.

5.1.5.1 Assembly or component

a) Type

b) Style

c) Nominal size

5.1.5.2 Process or end connections

a) Nominal size

b) Nominal rating

c) Termination category and type

d) Finish

e) Length and wall thickness

f) Location

g) Taps

5.1.5.3 Part

a) Type

b) Style

c) Quantity

d) Dimensions

5.1.5.4 Materials of construction

a) Primary material

b) Secondary materials



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

– 19 – ISA–20.00.03–2001

c) Bolting materials

d) External treatment material

e) End termination material

f) Gasket, packing, and seal materials

g) Accessories material

5.1.5.5 Performance characteristics

a) Design ratings

b) Working limits

c) Accuracy ratings

d) Measuring range limits

e) Performance factors

f) Rated coefficients

g) Performance ratings

h) Environmental limits

i) Supply limits and consumption

j) Signal and communication limits

5.1.5.6 Accessory hardware

a) Style

b) Nominal size

c) Standard options

d) Material of construction

e) Model number

5.1.5.7 Special requirements

a) Custom tag or nameplate

b) Referenced specification identification

c) Special preparation

d) Design compliance standard



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

ISA–20.00.03–2001 – 20 –

e) Construction code identification

f) Calculation requirement

g) Calibration report

h) Software configuration

i) Certification or approvals documentation

j) Special inspection

5.1.5.8 Physical data

a) Weight

b) Dimensions

c) Signal connection

d) Manufacturer's dimensional reference drawing

5.1.5.9 Calibrations and tests

a) Measurement range values

b) Control action

c) Signal range limits

d) Setpoint values

e) Test values

5.1.5.10 Component identifications

a) Component tag number

b) Component type

c) Style

d) Manufacturer

e) Composite model number

5.1.6 Content of General or Special Requirements form

The General or Special Requirements form, which is optional, has been developed to provide a form forattached requirements that cannot be adequately described in the Operating Parameters or DeviceSpecification forms. The first sheet of this form shall contain a note referencing the requirements as part ofthe specification, and a Table of Contents of the general or special requirements. The same specificationform identification header, revision chronicle, and remarks footer subsections used on the Operating



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

– 21 – ISA–20.00.03–2001

Parameters or Device Specification forms shall be included. Subsequent pages may use the same or adifferent format as appropriate for the attached references.

5.2 Form formats

5.2.1 Two form formats

ISA specification forms are provided in one of two format types: single main device format or multiplesimilar main devices formats. The quantity of the required operating parameters information will generallydetermine the format type that is appropriate for a specific device specification.

5.2.1.1 Single main device format

There shall be only one main device per specification form. The form may include attached and directlyassociated secondary devices.

5.2.1.2 Multiple similar main device format

Similar main devices can share a common hardware specification form and utilize a separate tabulationsheet to identify the variable data and unique tags.

5.2.2 Printing format

The page format has been established to readily accommodate typical printer capabilities and minimizethe pages required to accommodate the identified required content. The printing style shown on the ISAexample specification forms has been chosen for convenience of determining the maximum availableprompt and data field lengths. Alternate printing styles may be used if they produce the same results asthe following listed page format.

5.2.2.1 Page size

The page size shall be 8½ inches by 11 inches, or A4 size.

5.2.2.2 Columnar presentation

The form shall use multiple parallel columns of field prompts and data entry fields, with the following fieldor text area sizes (identified in characters), and the desired text alignments within the fields:

Size Text Area Description Text Alignment

3 Column for line number Right

2 Column for revision identification field Left

25 Column for field prompt area Left

25 (maximum)* Data entry field(s) Left

1 Space between a data entry field and its unit symbol field

1 (minimum) Space between a data entry field and a subsequent fieldprompt

* The data entry fields are generally limited to 25 total characters, but selected exceptions have been made for special conditionsthat require more characters.



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

ISA–20.00.03–2001 – 22 –

5.2.2.3 Data grouping

Related data shall be grouped as defined in this standard, and a text line shall contain the title for thegroup.

5.2.2.4 Top margin and print

The top margin shall be a minimum of one line or the printer’s minimum capability. The maximum requiredlines of printing shall be 84.

5.2.2.5 Left margin

The left margin shall be a minimum of 0.6 inch to allow for hole punches.

5.2.3 Numbering system format

5.2.3.1 Page size

There shall be unique line numbers for each form part. These unique numbers serve as references tospecific field prompts and data entry fields.

5.2.3.2 Consecutive line numbers within a part

The line numbers that correspond to the field prompts within a subgroup shall be consecutive.

5.3 Form terminology

The same field prompt terminology shall be used throughout all forms, sections, or subsections of a formto designate a given property. Use of an alternate term (synonym) for a concept already defined shall beavoided.

Field prompts from the ISA Draft TR20.00.04 (see annex A) master list shall be used whenever possible.

If new field prompt terms are necessary, they shall be listed and submitted for approval by ISA forinclusion in the ISA Draft TR20.00.04 master listing.

5.4 Data field content

Field prompts should be constructed to require only a single parameter for the data entry field response.Compound parameter responses would generally require complex help instructions, and a large pick list tocover all possible combinations of the individual properties.

Unit symbols relating to numeric data should be placed in separate fields to facilitate enumerated valuepick list and data conversion to alternate units.

6 Preparation of new specification forms

The specification forms are developed to reflect the data required for the selection and definition ofstandard, commercially available instrument devices. The methodology for developing the formsencompasses the application of this standard’s requirements while examining reference sources and theguidelines presented in this section.



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

– 23 – ISA–20.00.03–2001

6.1 Reference sources

6.1.1 Specification forms

The collection, whenever they are available, of similar specification forms from the following sources willfacilitate the development of new forms:

a) ISA forms for similar instruments developed in accord with this standard

b) ISA forms from ISA-20-1981 or other ISA standards

c) Standards organizations such as the International Electrotechnical Commission, Fluid ControlsInstitute, American Petroleum Institute, American Society of Mechanical Engineers, and Institute ofElectrical and Electronics Engineers

d) Instrument manufacturers and vendors

e) Other form users such as those from engineering and construction firms or end-user engineeringdepartments

6.1.2 Reference documents

The gathering, whenever they are available, of the following types of applicable terminology-relatedreference documents may facilitate the development of specification forms:

a) ISA device-associated standards, recommended practices, and technical reports; and the ISADictionary of Measurement and Control

b) Related standards from organizations such as the International Electrotechnical Commission, FluidControls Institute, American Petroleum Institute, American Society of Mechanical Engineers, andInstitute of Electrical and Electronics Engineers

c) Manufacturers’ device specifications and associated technical literature

d) Technical publications that contain sizing calculation methods or selection criteria

6.2 Review and modification of Operating Parameters forms

The appropriate measured variable or final device Operating Parameters form will generally be adequatefor new or revised devices, but must be checked against the requirements in 5.1.2. Identify andincorporate any necessary revisions that must be made to the existing Operating Parameters form.

6.3 Development guidelines for Device Specification forms

6.3.1 Specification identification header and footer

The Operating Parameters and Device Specification forms have been developed with fixed specificationidentification headers and footers. These shall be duplicated for new forms.

6.3.2 Component identification subsection

Device Specification forms have been developed with fixed component identifications subsections. Thisshall be duplicated for new forms.



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\

ISA–20.00.03–2001 – 24 –

6.3.3 Main device subsections

The main measurement or control device attributes generally can be subdivided into subsections.Determine if such subsection groupings exist for the device under consideration and establish thecorresponding device-specific titles for those subsections.

6.3.4 Main device subsection development and review

The form’s format can be most easily implemented by editing an existing form for a similar instrument.

Examine numerous manufacturers’ products literature and identify their required device property data forspecifying the device or component, while encompassing the following:

a) This standard’s content requirements identified in 5.1.3

b) The field prompt order identified in 5.1.5

c) The terminology from ISA Draft TR20.00.04 (see annex A) for terms not present on the example formbeing edited

There will generally be more field prompt candidates, based on the above criteria, than can beaccommodated on the form. The criteria may need to be prioritized and compromised to fit pagelimitations. The user-definable field prompts required in each subsection and the notes subsections willgenerally provide the flexibility to accommodate most applications.

6.3.5 Secondary device inclusion

The decision of when to include in the form the specification of an attached or directly associated deviceshould consider the following:

a) Forms should provide for attached equipment that is commonly used and available as a standardoption by most manufacturers

b) A supplemental page can be developed to provide for less commonly used attached or directlyassociated devices, such as has been provided for the control valves specification form

c) If it is desirable to have a second supplier provide the directly associated device, a separate form forthe device should be produced

6.4 Contextual help instructions

The contextual help instructions should clarify the field prompt’s context or definition and, preferably, beapplicable to all devices using that field prompt. Therefore, the only new contextual help instructions thatshould need development will occur when new field prompts are added to ISA Draft TR20.00.04 (seeannex A).

6.5 Pick list

Review of manufacturers’ literature and ISA Draft TR20.00.04 (see annex A) should be made to determinethe adequacy of the existing list to cover the new device. Unit symbols should be provided in both USCustomary and SI systems, and equivalent dimensions provided when available. New prompts should bebased on terminology from reference documents such as those identified in 6.1.2.



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

– 25 – ISA–20.00.03–2001

6.6 Data dictionary update

If ISA Draft TR20.0.04 (see annex A) does not contain adequate terms for the device specification underdevelopment, any proposed new data dictionary terms shall be submitted for approval along with the newor revised form.

6.7 Review and approval

After completing the form development with this standard’s requirements and guidelines, circulate thepreliminary form for review by peers and manufacturers. Consolidate the comments and send theproposed form to the Chairperson of ISA-SP20 as a request for interpretation of standards, for theproposed new or revised form, as an addendum or future revision to ISA–TR20.00.01–2001.

7 Classification and designation

Hardware device forms are grouped and numbered based upon the device’s measurement principles orcontrol functions. Consult ISA–TR20.00.01–2001, table A.1 or table A.2, when tentatively assigning newdevice categories, form numbers, and titles.



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^

^#^~

^^"~

~:~"

~$$"

~$^"

#:*~

"#@

^#~"

@"~

~*:#

*:^$

:$~:

*"\\




--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

– 27 – ISA–20.00.03–2001

Annex A (informative) — References

This annex is included for informational purposes and is not part of this standard. At the time ofpublication, the editions or drafts indicated below were valid. All standards, recommended practices, andtechnical reports are subject to revision, and parties to agreements based on this standard areencouraged to investigate the possibility of applying the most recent editions or drafts of the documentsindicated below.

ISA

ISA–TR20.00.01–2001 Specification Forms for Process Measurement and Control InstrumentsPart 1: General Considerations

ISA Draft 20.00.02 Specification Forms for Process Measurement and Control InstrumentsPart 2: Instructions for Using Specification Forms

ISA Draft TR20.00.04 Specification Forms for Process Measurement and Control InstrumentsPart 4: Data Dictionary

Available from: ISA–The Instrumentation, Systems, and Automation Society67 Alexander DrivePO Box 12277Research Triangle Park, NC 27709USATel: (919) 990-9200www.isa.org

ANSI

ANSI X3.50-1986 (R1997) Representations for U.S. Customary, SI, and Other Units to Be Used inSystems with Limited Character Sets

Available from: American National Standards Institute11 West 42nd StreetNew York, NY 10036 USATel: (212) 642-4900www.ansi.org



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

ISA–20.00.03–2001 – 28 –

ASME

ASME Y1.1-1989 Abbreviations for Use on Drawings and in Text

Available from: ASME3 Park AvenueNew York, NY 10016-5990USATel: (973) 882-1167www.asme.org

International Electrotechnical Commission (IEC)

IEC 60050-351 International Electrotechnical Vocabulary - Part 351: Automatic Control(1998-09)

Available from: IEC3, rue de VarembePO Box 1311211 Geneva 20SwitzerlandTel: 41 22 734 0150www.iec.ch

International Organization for Standardization (ISO)

ISO/CD 10303-221 Library of Classes for Process Plant Application Protocols

Available from: ISO1, rue de VarembePO Box 561211 Geneva 20SwitzerlandTel: 41 22 749 0111www.iso.ch



--`,,```,,,,````-`-`,,`,,`,`,,`---//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@

^#~"@"~~*:#*:^$:$~:*"\\




--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@

"~~*:#*:^$:$~:*"\\

Developing and promulgating sound consensus standards, recommended practices, and technical reports is one of ISA’s primary goals. To achieve this goal the Standards and Practices Department relies on the technical expertise and efforts of volunteer committee members, chairmen and reviewers.

ISA is an American National Standards Institute (ANSI) accredited organization. ISA administers United States Technical Advisory Groups (USTAGs) and provides secretariat support for International Electrotechnical Commission (IEC) and International Organization for Standardization (ISO) committees that develop process measurement and control standards. To obtain additional information on the Society’s standards program, please write:

ISA Attn: Standards Department 67 Alexander Drive P.O. Box 12277 Research Triangle Park, NC 27709

ISBN: 978-1-93756-000-3



--`,,```,,,,````-`-`,,`,,`,`,,`---

//^:^^#^~^^"~~:~"~$$"~$^"#:*~"#@^#~"@"~~*:#*:^$:$~:*"\\

Documents

ISA-TR20.00.01-2007 Measurement and Control Instruments