iPhone 6S Display Assembly Replacementodrepairservices.com/wp/PDF/iPhone6SFDA.pdf · cross-check by using a different display ... logic board: o Digitizer flex cable o LCD data/home

iPhone6SFullDisplayAssemblyReplacement

WerxParts www.werxparts.com Page1of16

iPhone 6S Full Display Assembly Replacement

INTRODUCTION Use this guide along with the Werx Repair Mat to replace the cracked or broken screen on your iPhone 6S. Follow Werx Repair Mat Steps 1,2,5 to disassemble. Reverse steps for re-assembly. Use this guide to strip and replace your iPhone 6S front panel. It will show you how to remove the home button, front-facing camera and sensor assembly, LCD shield plate, and home button ribbon cable. TOOLS: IMPORTANT Take your time! The repair takes about 20-30 minutes.

Remember that you will be handling fragile parts, so be gentle!

Most screws are different sizes so keep them organized.

Werx Repair Mat



Step 1: Pentalobe Screws

• Before disassembling your iPhone, be

sure it is powered off.

• Remove the two 3.6 mm Pentalobe

screws next to the lightning connector.

Step 2: Front Panel Assembly

• Press a suction cup into the screen,

just above the home button.

Be sure the cup is completely on the

screen to get a tight seal.



Step 3:

• While holding the iPhone down with

one hand, pull up on the suction cup to

slightly separate the front panel

assembly from the rear case.

Take your time and apply firm, constant

force. The display assembly is a much

tighter fit than most devices.

• With a plastic opening tool, begin to gently pry the display assembly, while you pull up with

the suction cup.

Step 4:

• Slide the flat end of the plastic spudger

along the perimeter of the frame to

separate the adhesive holding the

display assembly in place.



Step 5:

• Pull the home button end of the front

panel assembly away from the rear

case, using the top of the phone as a

hinge.

Keep the front panel supported at a 90

degree angle in relation to the rear

case.

Step 6:

• Several clips along the top edge of the

front panel form a partial hinge,

allowing the front panel assembly to

swing open like a book.

During reassembly, align the clips just

below the top edge of the rear case.

Then, slide the front panel upward until

its top edge is flush with that of the rear

case.



Step 7:

• Use the Werx repair mat to keep

screws organized and prevent screw

misplacement damage

• Remove the following 4 Phillips screws

securing the front panel assembly cable

bracket:

o Three 1.3 mm Phillips screws

o One 2.8 mm Phillips screw

Step 8:

• Remove the front panel assembly cable

bracket from the logic board.



Step 9:

• Using a plastic spudger, disconnect the

home button flex cable connector

connector.

Step 10:


front camera flex cable connector.



Step 11:


LCD/Digitizer cable connector.

Step 12:

• Remove the front panel assembly from

the rear case.



Step 13: Remove excess adhesive • Remove any lifted adhesive from the

edge of the frame using the flat end of

the plastic spudger.

Step 14: Test New Display Assembly • Connect the LCD and Digitizer flex

cables to test the new display

assembly.

• Ensure that the display is clear of

issues and that there are no dead spots

in the touch screen.

• If there are issues with the display

assembly, power off, disconnect and

reconnect screen. If issues persist,

cross-check by using a different display

assembly.



Step 15: Home Button

• Remove the three 1.7 mm Phillips

screws securing the home button

bracket.

Step 16:

• Remove the home button bracket from

the front panel by lifting and sliding it

out from underneath the bottom of the

LCD shield plate.



Step 17:

• Using the plastic spudger disconnect

the home button cable connector by

pushing it up and away from the home

button.

Step 18:

• Use the heat gun to heat the glass side

of the screen near the home button.

Keep the heat gun in constant motion

and do not overheat flex cable

• Use the flat end of the spudger to

separate the left-hand side of the home

button flex cable from the screen.



Step 19:

• Gently push the home button up away

from the front panel.

Do not push the home button all the

way through you only need to get a

corner free so that you can pry it free

with a spudger.

Step 20:

• Once all the adhesive has been

separated, remove the home button

from the front panel.



Step 21: Home Button

• Insert the home button to the front

panel.

• Ensure that the home button extension

connector is sitting flush on the display

assembly.

Step 22:

• Connect the home button cable

connector.



Step 23:

• Insert the home button bracket from the

front panel.

• Slide the top right corner of the home

button bracket underneath the LCD

shield plate and align screw holes.

Step 24:

• Insert the three Phillips screws securing

the home button bracket.



Step 25:

• Insert the LCD assembly to the rear

case.

• Connect the following flex cable to the

logic board:

o Digitizer flex cable

o LCD data/home button flex cable

o Front-facing camera and sensor

cable

Step 26:

• Insert the front panel assembly cable

bracket to the logic board.



Step 27:

• Insert four Phillips screws to securing

the front panel assembly cable bracket.

• Power on the device and test on

functions prior to sealing.

Step 28:

• Align the clips just below the top edge

of the rear case. Then, slide the front

panel upward until its top edge is flush

with the rear case.



Step 29:

• Run your fingers along the sides being

sure the assembly slips evenly into the

frame.

Step 30: Pentalobe Screws

• Insert the two Pentalobe screws next to

the lightning connector.

Documents

iPhone 6S Display Assembly Replacementodrepairservices.com/wp/PDF/iPhone6SFDA.pdf · cross-check by using a different display ... logic board: o Digitizer flex cable o LCD data/home