DC Power Controllers for use withContinuous Electrodeionization Modules

The DC Power Controllers are designed to be

used with the IONPURE® modules and are part of

a complete line of modular system components

offered to system integrators.

DC Power Controllers Featuresn Designed for individual power control for each

modulen Pre-engineered boards reduce system costn Compatible with DSP Display Boardsn Use DC Power Controllers in lieu of rectifiers for

enhanced system controln Reduced spares cost equals less downtime

For additional information on our PowerControllers call 866-876-3340 or visit our website at www.ionpure.com. Information on CEDImodules and our complete line of systemcomponents is also available.

Ionpure® DC Power Controllers

Single Phase Power Controller IP-200 / 400 / 600 VPCB

Three Phase Power Controller IP-600-20-VPCB

Ionpure is a trademark of Siemens its subsidiaries or affiliates.

The information provided in this brochure contains merely generaldescriptions or characteristics of performance which in actual caseof use do not always apply as described or which may change as aresult of further development of the products. An obligation toprovide the respective characteristics shall only exist if expresslyagreed in the terms of contract.

www.siemens.com/ionpure

Siemens

10 Technology DriveLowell, MA 01851Phone: 866.876.3340

© 2010 Siemens Water Technologies Corp.

HPS-C-VPCB.S-DS-0410

Subject to change without prior notice.

Ionpure® DC Power Controllers

Operating EnvironmentInstallation should be indoors with no directsunlight and it should have a maximum ambienttemperature of 122°F (50°C) up to 90% relativehumidity non-condensing

Quality Assurance Standards UL recognized. CE versions are available.* Eachboard is factory tested to meet strict Ionpure andindustry standards.

*Refer to operating manual for details

PHYSICAL SPECIFICATIONS

Item Number Height Width Depth Weight

IP-200VPCB 6.00” (152.4 mm) 6.00” (152.4 mm) 2.25” (57.2 mm) 1.6 lbs (0.72kg)

IP-400VPCB 6.00” (152.4 mm) 6.00” (152.4 mm) 2.25” (57.2 mm) 1.6 lbs (0.72kg)

IP-600VPCB 6.00” (152.4 mm) 6.00” (152.4 mm) 2.25” (57.2 mm) 1.6 lbs (0.72kg)

IP-600-20-VPCB 5.10” (129.5 mm) 5.10” (129.5 mm) 6.25” (158.7 mm) 10 lbs (4.5kg)

DESIGN SPECIFICATIONS

Item Number Description Volts Amperage Output

IP-200VPCB DC Power Controller 200VDC 2.5, 4, 6.5, 10

IP-400VPCB DC Power Controller 400VDC 2.5, 4, 6.5, 10

IP-600VPCB DC Power Controller 600VDC 2.5, 4, 6.5, 10

IP-600-20-VPCB DC Power Controller 600VDC 13.2, 20

ELECTRICAL REQUIREMENTS

Item Number Input Voltage

IP-200VPCB 115, 176, or 230 VAC 1Φ

IP-400VPCB 220, 330, or 440 VAC 1Φ

IP-600VPCB 440, 550, or 660 VAC 1Φ

IP-600-20-VPCB 468 VAC 3Φ

Rear View

DC PowerControllerDisplay Board

(Sold Separately)

Patch Cable IP-LXCABLE06(Sold seperately, additional lengths available.)

Note: Isolation transformer required. More detail in Operating Manual