Upload
others
View
8
Download
1
Embed Size (px)
Citation preview
I/O-System — 750 XTR Series Section 4 I/O-System — 750 XTR Series Section 6
I/O-System — 750 and 753 Series For demanding applications where the following are critical:
• Extreme temperature stability• Immunity to interference and dielectric strength• Vibration and shock resistance
I/O-System — SPEEDWAY
• Highly versatile• More than 500 modules available• Functional Safety• Ex i
• Uncompromising protection, even in the hars-hest environments outside the control cabinet
• Degree of protection: IP67• Fully encapsulated
5394
r g
& /
Taking it to the eXTReme — The standard for 750 XTRThe WAGO-I/O-SYSTEM 750 XTR is readily recognizable by its dark gray modules. Benefit from the unique features offered by this system in extreme environ-ment applications.
The WAGO-I/O-SYSTEM 750 XTR features outstanding characteristics: It is extremely temperature-resistant, immune to interferences, as well as insensitive to vibrations and impulse voltages. This is what makes 750 XTR the first choice for demanding applications, including:• Marine systems and onshore/offshore installations• Renewable energy systems (wind, photovoltaic and biogas plants)• Transformer stations and power distribution• Petrochemical industry• Water and wastewater treatment systems• Custom machine engineering• Railway applications
Additional protection against interference pulsesThe WAGO-I/O-SYSTEM 750 XTR provides greater isolation up to 5 kV of impulse voltage, lower EMC emission of interference and higher insensitivity against EMC interference. These strengths add up to trouble-free operation.
High mechanical performanceAutomation systems must be particularly vibration-resistant, especially when installed close to vibrati-on-prone and shock-generating system compon-ents. Powerful motors and power circuit breakers are just two examples of common disturbance-cre-ating components. The WAGO-I/O-SYSTEM 750 XTR is also setting new standards for automation systems with 5g of vibration resistance according to DIN EN 60068-2-6 (acceleration: 50 m/s2) and 15g (150 m/s2) or 25g (250 m/s2) of continuous shock resistance according to IEC 60068-2-27.Count on long-lasting, trouble-free operation and industry-topping levels of safety — even in the most torturous applications, such as a tunnel boring machines.
Worldwide approvalsInternational approvals for industrial automation, shipbuilding and onshore/offshore applica-tions guarantee worldwide use even under the harshest operating conditions, e.g., Germanischer Lloyd, Det Norske Veritas, American Bureau of Shipping, Korean Register of Shipping, Nippon Kaiji Kyokai, Registro Italiano Navale and Polski Rejestr Stratkow.
Superior reliability in extreme climatesAutomation systems are increasingly being located in outdoor and remote locations where components are directly affected by widely fluctu-ating temperatures conditions (e.g., wind turbines and transformer stations).Whether freezing cold, extreme heat or high humidity, the WAGO-I/O-SYSTEM 750 XTR is engineered for absolute dependability in all climatic conditions. This robust XTR version of the WAGO-I/O-SYSTEM 750 is unfazed by both freezing cold down to -40 °C and scorching heat up to +70 °C. And this applies to both initial start-up and daily operation.Another highlight is that the 750 XTR functions at elevations up to 5,000 m, opening up these ap-plications to new highs for safety, reliability and performance — even in the thin air of a mountain top station.
eXTRreme evolution of the tried and testedUsing an industry-leading platform, the WAGO-I/O-SYSTEM 750 XTR boasts the same proven benefits:• Compact design: up to 16 channels in just one 12 mm module • Easy to use• CAGE CLAMP® spring connection technology for vibration-proof, fast and maintenance-free connections • Fieldbus independence due to its modular design• Clear identification with the WAGO WSB marking system
I/O-System — 750 XTR SeriesGeneral Product Information
No air conditioning required - Compact footprint - Lower energy and maintenance costs Can be used in unshielded areas Maximum system uptime Install close to vibrating and shock-generating system components CAGE CLAMP® connection technology for vibration-proof, fast and maintenance-free connection
3955
5
I/O-System — 750 XTR SeriesItem Number Keys
Item No. : 750-yyzz/040-00x
Series
01zz: Marker03zz: Fieldbus Coupler zz: consecutive number
1yzz: 16 connection points or ribbon cablesy4zz: Input 00 ... 49 = Digital input 50 ... 99 = Analog input y5zz: Output 00 ... 49 = Digital output 50 ... 99 = Analog input y6zz: Communication/system modules 0z: Power supply, potential duplication, end module 1z: Power supply, separation module 2z: Filter 5z: Serial interface 09zz: Accessories
Explanation of the components for the item number key XTR Version
5396
A
C
a)
b)
c)
B
D
c)
b)
I/O-System — 750 XTR SeriesInterfaces and Configurations
Housing design fieldbus coupler (A)• Including supply module (a) to power down-
stream I/O modules• Technical differences on the connection level.
Fieldbus interface (b) and optional address switch (c)
• W x H* x L (mm) 51 x 65 x 100
Housing design fieldbus coupler ECO (B)• Constraint in regards to power supply and data
width• W x H* x L (mm) 50 x 65 x 97
Housing design 750 (C)• 8 connecting terminals (CAGE CLAMP®)• W x H* x L (mm) 12 x 62 x 100
Housing design 750 (D)• 16 connecting terminals (CAGE CLAMP® S)• W x H* x L (mm) 12 x 62 x 100
Miniature WSB quick marking system, blank, pre-marked and colored. Suitable for all I/O modules within the 750 Series.
Marker carrier for an individual I/O module. Suitable for all I/O modules within the 750 Series. The marker carrier can be accommodated in the upper miniature WSB carrier plate.
Marker carriers for an I/O node. Both carrier models (750-106 and 750-107) permit continuous marking regardless of the I/O module housing used.
Marking Accessories
3975
5
I/O-System — 750 XTR SeriesApplication and Installation Instructions
Attachment/release on the mounting rail
Secure, automatic connection of the power connection by self-cleaning blade contacts
Secure, automatic connection of the data and electronics power supply by gold-plated pressure contacts
Wide range of accessories for EMC-compliant installation including shield connection
Service interface for configuring the fieldbus coupler. Connectivity via configuration cable or radio adapter
Notice:For some I/O modules, not all power jumper contacts are made! An I/O module with three power jumper contacts (e.g., 2-channel digital input) cannot be snapped into place behind an I/O module in which not every contact is made.
To increase electromagnetic compatibility (EMC), some components are connected to the DIN-rail by a discharge contact. The DIN-rail must always have a low-resistance connection to the ground potential.
5398
I/O-System — 750 XTR Series Application and Installation Instructions
Power supplyThe fieldbus coupler always powers the internal electronics’ power supply. The power supply to the field-side supply is electrically isolated. The division enables a separate supply for sensors and actuators. The I/O modules’ connections automatically lead to transferring the supply voltages. Supply modules with diagnostics enable additional power supply monitoring. This ensures a flexible, user-specific supply design for a station.The current supply to the electronics is limited by a maximum value. This value depends on the fieldbus coupler used. If the sum of the internal current demand of all the I/O modules exceeds this value, an additional bus supply module is ne-cessary. Even in this case, the power supply to the field-side supply of 10 A may not be exceeded. However, different power supply modules allow a new power supply, formation of potential groups and the implementation of emergency stops.
Interference-free in safety-related applica-tionsTo easily and safely perform cost-effective, cen-tralized deactivation of complete actuator groups the actuator’s power supply can be switched off using a safety switching device. This can either be performed for each individual actuator or by turning off the power supply to a group of control outputs.In the event of failure, ensure that no interference from other current or power circuits occurs — even when the control voltage is switched off — so the defined safety function properties (logic and time response) remain unchanged.
All modules are designed to provide interference-free safety functionality. These modules comply with safety requirements up to Category 4 of DIN EN ISO 13849-1:2007. The safety category and performance level depend solely on the safety components and their wiring.
Attention!Interference-free WAGO I/O modules have no active influence on the safety function, they are not an active part of the safety application and are not a substitute for the safety switching device! When using the components in safety functions, the corresponding notes must be obser-ved in the relevant manual.
Example: Two-channel, double-pole power supply disconnection
NoticesAdditional steps must be must be implemented based on where the I/O-System is installed:• As part of shipbuilding or in onshore/offshore
installations, as well as in telecontrol applications, specific power and field-side power supply filters must be provided (750-624/040-001 or 750-626/040-000)
Please refer to the manual for details about the power supply’s design.
Mixed operation:Mixed operation (standard/XTR modules) within a node is possible when groups of modules are electrically isolated on the field side (i.e., electrically isolated power supply). The combination may be useful, for example, when there are only increased requirements for dielectic strength and immunity to interference, but the ambient temperature is not critical.
End
Mod
ule
Supp
ly M
odul
e
Bus M
odul
e
Field
bus C
oupl
er
with
Su
pply
Mod
ule
24 V Electronics
24 V Field potential 1
230 V Field potential 2
24 V Field potential 3
1 4
2 5
3 6 4 8
3 7
2 6
1 5
24 V
0 V
24 V
0 V
D01 D02
Safety switch module/Safety module
Supply module Output module
24 V voltage supply0 V voltage supply
Safetycomponents
Safeoutput
Safeoutput
Safeinput
Safeinput
Logic
Actuator 2
Actuator 1
3995
5
I/O-System — 750 XTR SeriesStandards and Rated Conditions
General SpecificationsOperating voltage 24 VDC
under laboratory conditions +15 °C … +35 °C: 18 V ... 31.2 V (17.4 V ... 31.2 V)1)
for -40 °C ... +55 °C: 18 V ... 28.8 V (17.4 V ... 28.8 V)1)
for +55 °C ... +70 °C: 18 V ... 26.4 V (17.4 V ... 26.4 V)1)
1) Including residual ripple of 15 %Operating temperature -40 °C ... +70 °CStorage temperature -40 °C ... +85 °CRelative humidity Max. 95 % short-term condensation acc. to class 3K7 / IEC
EN 60721-3-3 (excluding wind-driven precipitation, water and ice formation)
Operating altitude without temperature derating: 0 m ... 2000 m; with temperature derating: 2000 m ... 5000 m (0.5 K/100 m); max.: 5000 m
Degree of contamination II acc. to IEC 61131-2Dielectric strength acc. to (EN 60870-2-1)
Module ≤ 50 V: 510 VAC/775 VDC; Module > 50 V: 2.5 kVAC/3.5 VDCIsolation: Rated surge voltageModule ≤ 50 V: 1 kV (class VW1 acc. to EN 60870-2-1)Module > 50 V: 5 kV (class VW3 acc. to EN 60870-2-1)Surge:Module ≤ 50 V: 1 kV (L - L) / 2 kV (L – E)Module > 50 V: 2 kV (L - L) / 4 kV (L – E)Overvoltage category: III
Vibration resistance 5g acc. to IEC 60068-2-6, EN 60870-2-2, IEC 60721-3-1, IEC 60721-3-3, EN 61131-2
Shock resistance 15g/11 ms/half-sine/1000 shocks acc. to IEC 60068-2-2725g/6 ms/1000 shocks acc. to IEC60068-2-27
EMC immunity to interference EN 61000-6-1, EN 61000-6-2, EN 61131-2Marine applications, EN 50121-3-2, EN 50121-4EN 50121-5, EN 60255-26, EN 60870-2-1EN 61850-3, IEC 61000-6-5, IEEE 1613, VDEW: 1994
EMC emission of interference EN 61000-6-3 and EN 61000-6-4, EN 61131-2EN 60255-26, marine applicationsEN 60870-2-1 (industrial and residential areas)EN 61850-3 (industrial and residential areas)EN 50121-3-2, EN 50121-4, EN 50121-5
Protection type IP20Mounting position standing horizontal/lying, verticalType of mounting on DIN-railHousing material Polycarbonate, polyamide 6.6Stress due to contaminants acc. to IEC 60068-2-42 and IEC 60068-2-43Maximum pollutant concentration with a relative humidity < 75 % SO2 ≤ 25 ppm; H2S ≤ 10 ppm
Connection technology CAGE CLAMP® (for standard I/O modules and fieldbus couplers)
Conductor cross-section; stripped lengths for standard I/O modules and fieldbus couplers: ECO fieldbus couplers:
0.25 mm² … 2.5 mm²/24 … 14 AWG; 8 … 9 mm/0.33 in.0.25 mm² … 1.5 mm²/24 … 16 AWG; 5 … 6 mm/0.22 in.
Connection technology CAGE CLAMP® S (for I/O modules with 16 connecting terminals)
Conductor cross-section; stripped lengths for I/O modules with 16 connecting terminals: 0.25 mm² … 1.5 mm²/24 … 16 AWG; 8 … 9 mm/0.33 in.
Current via power jumper contacts max. 10 A
750-333/040-000
5400
PROFIBUS DP/V1 Fieldbus Couplerfor eXTReme environmental conditions; 12 Mbaud; digital and analog signals
RUN
BF
DIA
I/O
PROFIBUS
x1012345678
9
x10012345678
9
ADDRESS
BUS
750-
333
/040
-000
W
24V 0V
+ +
— —
01 02ABCD
Data contacts
FieldbusconnectionD-Sub
Address
Power jumper contacts
0 V
Supply viapower jumper contacts24 V
Supply24 V0 V
Status voltage supply-System-Power jumper contacts
Address
Configurationinterface
The 750-333 Fieldbus Coupler maps the peripheral data of all the I/O modules of the WAGO-I/O-SYSTEM on PROFIBUS DP.When initializing, the coupler determines the node's module structure and creates the process image of all inputs and outputs. In order to optimize addres-ses, the I/O modules with a bit width smaller than 8 are grouped in one byte.It is furthermore possible to deactivate I/O modules and to modify the image of the node according to the connected signals without having to modify the existing application.
The diagnostic concept is based on ID- and channel-related diagnostics according to EN 50170. This does away with the need for programmingmodules to evaluate manufacturer-specific diagnostic data.
The module is ideally suited for operation in harsh environmental conditions:- strongly extended temperature range - higher dielectric strength and EMC resistance- higher vibration and shock resistance
Notice: GSD files required
Description Item No. Pack. Unit
PROFIBUS DP/V1 12 Mbd /XTR 750-333/040-000 1
Accessories Item No. Pack. Unit
GSD files Download: www.wago.comMiniature WSB Quick marking system
plain 248-501 5with marking see Section 11
Standards and ApprovalsStandard EN 50170Conformity marking 1
Korea CertificationMarine applications GLr UL 508 r ANSI/ISA 12.12.01 Class I, Div. 2, Grp. ABCD, T4
System DataNo. of couplers connected to Master 96 with repeaterMax. no. of I/O points approx. 6000 (depends on master)Transmission medium Cu cable acc. to EN 50170Max. length of fieldbus segment 100 m ... 1200 m
(depends on baud rate/cable)Baud rate 9.6 Kbaud ... 12 MbaudTransmission time typ. 1 ms (10 couplers; 32 digital I/Os per
coupler at 12 Mbaud) max. 3.3 msBuscoupler connection 1 x D-Sub 9; socket
5401
5
1
2
3
4
5
6
7
8
750-333/040-000
24 V
47 nF
24 V
47 nF
0 V
24 V /0 V
24 V
0 V
0 V5 V
5 V24 V
ELECTRONICS
I/Omodules
FIELDBUSINTERFACE
ELEC
TRO
NIC
S
FIEL
DBU
SIN
TERF
ACE
Technical DataNumber of I/O modules 63Fieldbus
Max. input process image 244 bytesMax. output process image 244 bytes
Configuration via PC or PLCPower supply via CAGE CLAMP® connections, 24 VDCMax. input current (24 V) 500 mAPower supply efficiency 90 %Internal current consumption (5 V) 200 mATotal current for I/O modules (5 V) 1800 mAVoltage via power jumper contacts 24 V DC
under laboratory conditions +15 °C ... +35 °C 18 V ... 31.2 V (17.4 V ... 31.2 V)1)
for -40 °C ... +55 °C 18 V ... 28.8 V (17.4 V ... 28.8 V)1)
for +55 °C ... +70 °C 18 V ... 26.4 V (17.4 V ... 26.4 V)1)
1) including residual ripple of 15 %Current via power jumper contacts (max.) 10 A DCIsolation (peak value) 510 VAC or 775 VDC power supply/DIN
railRated surge voltage 1 kVOvervoltage category III
General SpecificationsOperating temperature -40 °C ... +70 °CWire connection CAGE CLAMP®
Cross sections 0.25 mm² ... 2.5 mm² / AWG 24 ... 14Strip lengths 8 ... 9 mm / 0.33 inDimensions (mm) W x H x L 51 x 65 x 100
Height from upper-edge of DIN 35 railWeight 179.6 gStorage temperature -40 °C ... +85 °CRelative humidity 95 %, short-term condensation acc. to class
3K7 / IEC EN 60721-3-3 (except wind-driven precipitation, water and ice formation)
Vibration resistance acc. to IEC 60068-2-6 (acceleration: 5g), EN 60870-2-2, IEC 60721-3-1, -3, EN 61131-2
Shock resistance acc. to IEC 60068-2-27Degree of protection IP20EMC immunity of interference acc. to EN 61000-6-2, EN 61131-2,
marine applications, EN 50121-3-2, -4, -5, EN 60255-26, EN 60870-2-1, EN 61850-3, IEC 61000-6-5, IEEE 1613, VDEW: 1994
EMC emission of interference acc. to EN 61000-6-4, EN 61131-2, EN 60255-26, marine applications, EN 60870-2-1, EN 61850-3, EN 50121-3-2, -4, -5
Operating altitude without temperature derating: 0 m ... 2000 m; with temperature derating: 2000 m ... 5000 m (0.5 K/100 m); max.: 5000 m
750-352/040-000
5402
ETHERNET Fieldbus Couplerfor eXTReme environmental conditions; 10/100 Mbit/s; digital and analog signals
24VX3
X1
1
8
ON
0: WBM255: DHCP
X2
0V
I/O
NS
MS
LINKACT 1LINKACT 2
ETHERNET
W75
0-35
2/04
0-00
0
12
34
56
78
ON
Fieldbus connectionRJ-45
Address
Supply24 V0 V
Fieldbus connectionRJ-45 Configuration and
programming interface
Data contacts
Marking area
Status indication-Fieldbus-Fieldbus node
The 750-352 ETHERNET Fieldbus Coupler connects ETHERNET to the modular WAGO-I/O-SYSTEM.The fieldbus coupler automatically configures, creating a local process image which may include analog, digital or specialty modules. Analog and specialty module data is sent via words and/or bytes; digital data is sent bit by bit.Two ETHERNET interfaces and an integrated switch allow the fieldbus to be wired in a line topology. This eliminates the need for additional network devices, such as switches or hubs. Both interfaces support Auto-Negotiation and Auto-MDI(X).The DIP switch configures the last byte of the IP address and may be used for IP address assignment (DHCP, BootP, static).The coupler is designed for fieldbus communication in both EtherNet/IP and MODBUS networks. It also supports a wide variety of standard ETHERNET protocols (e.g., HTTP, BootP, DHCP, DNS, SNMP, FTP). An integrated Web ser-ver provides configuration options and status information from the coupler.The coupler has an integrated supply terminal for the system voltage. The field power jumper contacts are supplied via a separate supply module.
The module is ideally suited for operation in harsh environmental conditions:- strongly extended temperature range - higher dielectric strength and EMC resistance- higher vibration and shock resistance
Description Item No. Pack. Unit
ETHERNET Fieldbus Coupler /XTR 750-352/040-000 1
Accessories Item No. Pack. Unit
Miniature WSB Quick marking systemplain 248-501 5with marking see Section 11
ApprovalsConformity marking 1
Korea CertificationMarine applications GLr UL 508 r ANSI/ISA 12.12.01 Class I, Div. 2, Grp. ABCD, T4
System DataNo. of couplers connected to Master limited by ETHERNET specificationTransmission medium Twisted Pair S-UTP
100 Ω, Cat 5; Max. line length: 100 m
Baud rate 10/100 Mbit/sTransmission performance Class D acc. to EN 50173Buscoupler connection 2 x RJ-45Protocols EtherNet/IP, MODBUS/TCP (UDP), HTTP,
BootP, DHCP, DNS, FTP, SNMP
5403
5
DCDC
24 V
47 nF
47 nF
24 V
0 V
0 V
750-352/040-000
ELECTRONICS
I/Omodules
FIEL
DBU
S IN
TERF
ACE
ELEC
TRO
NIC
S
FIE
LDBU
SIN
TERF
ACE
Technical DataNumber of I/O modules 64
with bus extension 250Fieldbus
Max. input process image 1020 wordsMax. output process image 1020 words
Configuration via PCPower supply via CAGE CLAMP® connections, 24 VDCInput current typ. at rated load (24 V) 280 mAEfficiency of the power supply (typ.) at nominal load (24 V) 90 %Internal current consumption (5 V) 450 mATotal current for I/O modules (5 V) 700 mAVoltage via power jumper contacts 24 V DC
under laboratory conditions +15 °C ... +35 °C 18 V ... 31.2 V (17.4 V ... 31.2 V)1)
for -40 °C ... +55 °C 18 V ... 28.8 V (17.4 V ... 28.8 V)1)
for +55 °C ... +70 °C 18 V ... 26.4 V (17.4 V ... 26.4 V)1)
1) including residual ripple of 15 %Isolation (peak value) 510 VAC or 775 VDC
power supply/DIN railRated surge voltage 1 kVOvervoltage category III
General SpecificationsOperating temperature -40 °C ... +70 °CWire connection CAGE CLAMP®
Cross sections 0.25 mm² ... 1.5 mm² / AWG 24 ... 14Strip lengths 5 ... 6 mm / 0.22 inDimensions (mm) W x H x L 50 x 65 x 100
Height from upper-edge of DIN 35 railWeight 80.6 gStorage temperature -40 °C ... +85 °CRelative humidity 95 %, short-term condensation acc. to class
3K7 / IEC EN 60721-3-3 (except wind-driven precipitation, water and ice formation)
Vibration resistance acc. to IEC 60068-2-6 (acceleration: 5g), EN 60870-2-2, IEC 60721-3-1, -3, EN 61131-2
Shock resistance acc. to IEC 60068-2-27Degree of protection IP20EMC immunity of interference acc. to EN 61000-6-1, -2, EN 61131-2,
marine applications, EN 50121-3-2, -4, -5, EN 60255-26, EN 60870-2-1, EN 61850-3, IEC 61000-6-5, IEEE 1613, VDEW: 1994
EMC emission of interference acc. to EN 61000-6-3, -4, EN 61131-2, EN 60255-26, marine applications, EN 60870-2-1, EN 61850-3, EN 50121-3-2, -4, -5
Operating altitude without temperature derating: 0 m ... 2000 m; with temperature derating: 2000 m ... 5000 m (0.5 K/100 m); max.: 5000 m
750-338/040-000
5404
CANopen Fieldbus Coupler D-Subfor eXTReme environmental conditions; 10 kbaud ... 1 Mbaud; digital and analog signals
I/O
750-
338
/040
-000
W
24V 0V
+ +
— —
STOP
RUN
TX
CANopen
RXOVERFLOW
12
34
56
78
ON
ABCD
01 02
Data contacts
FieldbusconnectionD-Sub
Power jumper contacts
0 V
Supply viapower jumper contacts24 V
Supply24 V0 V
Status voltage supply-System-Power jumper contacts
DIP switchfor node IDand baud rate
Configurationinterface
The 750-338/040-000 Fieldbus Coupler connects the WAGO-I/O-SYSTEM as a slave to the CANopen fieldbus. Data is transmitted via PDOs and SDOs.The fieldbus coupler automatically configures, creating a local process image which may include analog, digital or specialty modules. Analog and specialty module data is sent via words and/or bytes, digital data is sent bit by bit.The local process image is divided into two data zones containing the data received and the data to be sent. The process data can be sent via the CANopen bus to a control system for further processing. The process output data can be sent via the CANopen bus.The data of the analog modules is stored in the PDOs according to the order in which the modules are connected to the coupler. The bits of the digital modules are sent byte by byte and also mapped in the PDOs. If the amount of digital information exceeds 8 bits, the buscoupler automatically starts with a new byte.All entries of the object directory can be mapped as required in the 32 Rx PDOs and 32 Tx PDOs. The complete input and output process image can be transmitted via SDOs.Spacer modules can be set via software.
The module is ideally suited for operation in harsh environmental conditions:- strongly extended temperature range - higher dielectric strength and EMC resistance- higher vibration and shock resistance
Description Item No. Pack. Unit
CANopen D-Sub /XTR 750-338/040-000 1
Accessories Item No. Pack. Unit
EDS files Download: www.wago.comMiniature WSB Quick marking system
plain 248-501 5with marking see Section 11
ApprovalsConformity marking 1
Korea CertificationMarine applications GLr UL 508 r ANSI/ISA 12.12.01 Class I, Div. 2, Grp. ABCD, T4
System DataNo. of couplers connected to Master 110Transmission medium Shielded Cu cable 3 x 0.25 mm²Max. length of bus line 30 m ... 1000 m
(depends on baud rate/cable)Baud rate 10 Kbaud ... 1 MbaudBuscoupler connection 1 x D-Sub 9; plug
5405
5
1
2
3
4
5
6
7
8
1) 2)
24 V
24 V
0 V
24 V /0 V
24 V
0 V
0 V
47 nF
47 nF5 V
5 V24 V
2) 10 nF /1 kV1) 2 MΩ
750-338/040-000
ELECTRONICS
I/Omodules
FIELDBUSINTERFACE
ELEC
TRO
NIC
S
FIEL
DBU
SIN
TERF
ACE
Technical DataNumber of I/O modules 64Fieldbus
Max. input process image 512 bytesMax. output process image 512 bytes
Configuration via PC or PLCNo. of PDOs 32 Tx / 32 RxNo. of SDOs 2 server SDOsCommunication profile DS-301 V4.1Device profile DS 401 V2.0
Marginal check Edge-triggered PDOsProgrammable error response
COB ID distribution SDO, standardNode ID distribution DIP switchesOther CANopen features NMT slave
Minimum boot-upVariable PDO mappingEmergency messageLife guardingConfiguration of virtual modules
Power supply via CAGE CLAMP® connections, 24 VDCMax. input current (24 V) 500 mAPower supply efficiency 90 %Internal current consumption (5 V) 350 mATotal current for I/O modules (5 V) 1650 mAVoltage via power jumper contacts 24 V DC
under laboratory conditions +15 °C ... +35 °C 18 V ... 31.2 V (17.4 V ... 31.2 V)1)
for -40 °C ... +55 °C 18 V ... 28.8 V (17.4 V ... 28.8 V)1)
for +55 °C ... +70 °C 18 V ... 26.4 V (17.4 V ... 26.4 V)1)
1) including residual ripple of 15 %Current via power jumper contacts (max.) 10 A DCIsolation (peak value) 510 VAC or 775 VDC
power supply/DIN railRated surge voltage 1 kVOvervoltage category III
General SpecificationsOperating temperature -40 °C ... +70 °CWire connection CAGE CLAMP®
Cross sections 0.25 mm² ... 2.5 mm² / AWG 24 ... 14Strip lengths 8 ... 9 mm / 0.33 inDimensions (mm) W x H x L 51 x 65 x 100
Height from upper-edge of DIN 35 railWeight 200 gStorage temperature -40 °C ... +85 °CRelative humidity 95 %, short-term condensation acc. to class
3K7 / IEC EN 60721-3-3 (except wind-driven precipitation, water and ice formation)
Vibration resistance acc. to IEC 60068-2-6 (acceleration: 5g), EN 60870-2-2, IEC 60721-3-1, -3, EN 61131-2
Shock resistance acc. to IEC 60068-2-27Degree of protection IP20EMC immunity of interference acc. to EN 61000-6-1, -2, EN 61131-2,
marine applications, EN 50121-3-2, -4, -5, EN 60255-26
EMC emission of interference acc. to EN 61000-6-3, -4, EN 61131-2, EN 60255-26, marine applications, EN 60870-2-1, EN 61850-3, EN 50121-3-2, -4, -5
Operating altitude without temperature derating: 0 m ... 2000 m; with temperature derating: 2000 m ... 5000 m (0.5 K/100 m); max.: 5000 m
750-1415/040-000
5406
8-Channel Digital Input Module 24 VDCfor eXTReme environmental conditions; high-side switching, 2-wire connection
1
1 9
2 10
3 11
4 12
5 13
6 14
7 15
8 16
2345678
750-1415/040-000
13 14
24 VCAGE CLAMP®Sconnection
DI 1 … DI 8
Data contacts
Power jumper contacts
StatusDI 1 ... DI 8
1
2
3
4
5
6
7
8
13
12
11
10
9
14
15
16
750-1415/040-000
10nF
10nF 10nF
DI 1
DI 2
DI 3
DI 4
DI 5
DI 6
DI 7
DI 8
0 V
+ 24 V
24 V
24 V
24 V
24 V
24 V
24 V
24 V
24 V
DI
0 V
+ 24 V
DI
This 2-wire digital input module provides 8 channels at a width of just 12 mm.It receives binary control signals from digital field devices (e.g., sensors, encoders, switches or proximity switches).The module features CAGE CLAMP® S connections providing push-in termination of solid conductors.Each input channel has a noise-rejection RC filter with 3.0 ms time constant.A green LED indicates the switched status of each channel.Field and system levels are electrically isolated.
An operating tool with a 2.5 mm blade (210-719) is required to open the CAGE CLAMP® S connections.
The module is ideally suited for operation in harsh environmental conditions:- extended temperature range- higher dielectric strength and EMC resistance- higher vibration and shock resistance
Description Item No. Pack. Unit
8DI 24VDC 3.0ms, 2-wire connection /XTR 750-1415/040-000 1
Accessories Item No. Pack. Unit
Miniature WSB Quick marking systemplain 248-501 5with marking see Section 11
Operating tool, with partially insulated shaft, type 1, blade (2.5 x 0.4) mm
210-719 50
ApprovalsConformity marking 1
Korea CertificationMarine applications GLr UL 508 r ANSI/ISA 12.12.01 Class I, Div. 2, Grp. ABCD, T4
Technical DataWire connection CAGE CLAMP® SCross sections 0.25 mm² ... 1.5 mm² / AWG 24 ... 16Strip lengths 8 ... 9 mm / 0.33 inDimensions (mm) W x H x L 12 x 62 x 100
Height from upper-edge of DIN 35 railWeight 46.8 gOperating temperature -40 °C ... +70 °CStorage temperature -40 °C ... +85 °CRelative humidity 95 %, short-term condensation acc. to class
3K7 / IEC EN 60721-3-3 (except wind-driven precipitation, water and ice formation)
Operating altitude without temperature derating: 0 m ... 2000 m; with temperature derating: 2000 m ... 5000 m (0.5 K/100 m); max.: 5000 m
Technical DataNumber of inputs 8Input type High-side switchingSignal voltage (0) -3 V ... +5 VDC (Type 1/3)Signal voltage (1) +11 V ... +30 VDC (Type 3)Input current (typ.) +1.6 mA (at 5 VDC)
+4.3 mA ... +4.6 mA (at 24 VDC)Input filter 3.0 msCurrent consumption (internal) 6 mACurrent consumption typ. (field side) 2 mAVoltage via power jumper contacts 24 VDC
under laboratory conditions +15 °C ... +35 °C 18 V ... 31.2 V (17.4 V ... 31.2 V)1)
for -40 °C ... +55 °C 18 V ... 28.8 V (17.4 V ... 28.8 V)1)
for +55 °C ... +70 °C 18 V ... 26.4 V (17.4 V ... 26.4 V)1)
1) including residual ripple of 15 %Current via power jumper contacts (max.) 10 AIsolation (peak value) 510 VAC or 775 VDC
power supply/DIN railRated surge voltage 1 kVOvervoltage category IIIBit width 8 bitsVibration resistance acc. to IEC 60068-2-6 (acceleration: 5g),
EN 60870-2-2, IEC 60721-3-1, -3, EN 61131-2
Shock resistance acc. to IEC 60068-2-27EMC immunity of interference acc. to EN 61000-6-1, -2, EN 61131-2,
marine applications, EN 50121-3-2, -4, -5, EN 60255-26, EN 60870-2-1, EN 61850-3, IEC 61000-6-5, IEEE 1613, VDEW: 1994
EMC emission of interference acc. to EN 61000-6-3, -4, EN 61131-2, EN 60255-26, marine applications, EN 60870-2-1, EN 61850-3, EN 50121-3-2, -4, -5
750-1415/040-000
750-1405/040-000
5407
5
16-Channel Digital Input Module 24 VDCfor eXTReme environmental conditions; high-side switching
1
1 2
3 4
5 6
7 8
9 10
11 12
13 14
15 16
23 45 67 89 1011 1213 1415 16
750-1405/040-000
13 14
StatusDI 1 ... DI 16 Data contacts
CAGE CLAMP®SconnectionDI 1 … DI 16
Power jumper contacts
1
750-1405/040-000
10nF
10nF 10nF
3
5
7
9
11
13
15
10
8
6
4
2
12
14
16
DI 1
DI 3
DI 5
DI 7
DI 9
DI 11
DI 13
DI 15
0 V
+ 24 V
DI 2
DI 4
DI 6
DI 8
DI 10
DI 12
DI 14
DI 16
DI
0 V
+ 24 V
DI
This digital input module provides 16 channels at a width of just 12 mm.It receives binary control signals from digital field devices (e.g., sensors, encoders, switches or proximity switches).The module features CAGE CLAMP® S connections providing push-in termination of solid conductors. Each input channel has a noise-rejection RC filter with 3.0 ms time constant.A green LED indicates the switched status of each channel.Field and system levels are electrically isolated.
The module is ideally suited for operation in harsh environmental conditions:- extended temperature range- higher dielectric strength and EMC resistance- higher vibration and shock resistance
Description Item No. Pack. Unit
16DI 24VDC 3.0ms /XTR 750-1405/040-000 1
Accessories Item No. Pack. Unit
Miniature WSB Quick marking systemplain 248-501 5with marking see Section 11
Operating tool, with partially insulated shaft, type 1, blade (2.5 x 0.4) mm
210-719 50
ApprovalsConformity marking 1
Korea CertificationMarine applications GLr UL 508 r ANSI/ISA 12.12.01 Class I, Div. 2, Grp. ABCD, T4
Technical DataWire connection CAGE CLAMP® SCross sections 0.25 mm² ... 1.5 mm² / AWG 24 ... 16Strip lengths 8 ... 9 mm / 0.33 inDimensions (mm) W x H x L 12 x 62 x 100
Height from upper-edge of DIN 35 railWeight 60 gOperating temperature -40 °C ... +70 °CStorage temperature -40 °C ... +85 °CRelative humidity 95 %, short-term condensation acc. to class
3K7 / IEC EN 60721-3-3 (except wind-driven precipitation, water and ice formation)
Operating altitude without temperature derating: 0 m ... 2000 m; with temperature derating: 2000 m ... 5000 m (0.5 K/100 m); max.: 5000 m
Technical DataNumber of inputs 16Input type Type 1 (IEC 61131-2), high-side switchingSignal voltage (0) -3 V ... +5 VDCSignal voltage (1) 15 V ... 30 VDCInput current (typ.) +0.6 mA (at 5 VDC)
+2.1 mA ... +2.4 mA (at 24 VDC)Input filter 3.0 msDelay time "0" > "1" 3 msDelay time "1" > "0" 4 msCurrent consumption (internal) 25 mAVoltage via power jumper contacts 24 VDC
under laboratory conditions +15 °C ... +35 °C 18 V ... 31.2 V (17.4 V ... 31.2 V)1)
for -40 °C ... +55 °C 18 V ... 28.8 V (17.4 V ... 28.8 V)1)
for +55 °C ... +70 °C 18 V ... 26.4 V (17.4 V ... 26.4 V)1)
1) including residual ripple of 15 %Current via power jumper contacts (max.) 10 AIsolation (peak value) 510 VAC or 775 VDC
power supply/DIN railRated surge voltage 1 kVOvervoltage category IIIBit width 16 bitsVibration resistance acc. to IEC 60068-2-6 (acceleration: 5g),
EN 60870-2-2, IEC 60721-3-1, -3, EN 61131-2
Shock resistance acc. to IEC 60068-2-27EMC immunity of interference acc. to EN 61000-6-1, -2, EN 61131-2,
marine applications, EN 50121-3-2, -4, -5, EN 60255-26, EN 60870-2-1, EN 61850-3, IEC 61000-6-5, IEEE 1613, VDEW: 1994
EMC emission of interference acc. to EN 61000-6-3, -4, EN 61131-2, EN 60255-26, marine applications, EN 60870-2-1, EN 61850-3, EN 50121-3-2, -4, -5
750-1405/040-000
750-407/040-000
5408
2-Channel Digital Input Module 220 VDCfor eXTReme environmental conditions; 2- to 4-wire connection; high-side switching
750-407/040-000
+ — + —
13 14
+ +
— —
ABCD
EFGH
13 14
Data contacts
Power jumper contacts
DI 2DI 1
220 V
0 V
Status DI 2Status DI 1
0 V
220 V220 V
0 V
750-407/040-000
DI 2DI 1 DI
DI 2.2nF 1.1nF
1.1nF
This digital input module receives control signals from digital field devices (e.g., sensors).The module is a 4-conductor device allowing direct connection of sensors with ground contact.Each input module has a 3.0 ms noise-rejection filter.Field and system levels are electrically isolated.When using the ground CAGE CLAMP® connection, the field power must be reapplied after every seven 750-407/040-000 I/O modules!
The module is ideally suited for operation in harsh environmental conditions:- extended temperature range- higher dielectric strength and EMC resistance- higher vibration and shock resistance
Description Item No. Pack. Unit
2DI 220VDC 3.0ms /XTR 750-407/040-000 1
Accessories Item No. Pack. Unit
Miniature WSB Quick marking systemplain 248-501 5with marking see Section 11
ApprovalsConformity marking 1
Korea CertificationMarine applications GLr UL 508 r ANSI/ISA 12.12.01 Class I, Div. 2, Grp. ABCD, T4
Technical DataWire connection CAGE CLAMP®
Cross sections 0.25 mm² ... 2.5 mm² / AWG 24 ... 14Strip lengths 8 ... 9 mm / 0.33 inDimensions (mm) W x H x L 12 x 62 x 100
Height from upper-edge of DIN 35 railWeight 48 gOperating temperature -40 °C ... +70 °CStorage temperature -40 °C ... +85 °CRelative humidity 95 %, short-term condensation acc. to class
3K7 / IEC EN 60721-3-3 (except wind-driven precipitation, water and ice formation)
Operating altitude without temperature derating: 0 m ... 2000 m; with temperature derating: 2000 m ... 5000 m (0.5 K/100 m); max.: 5000 m
Technical DataNumber of inputs 2Signal voltage (0) -3 V ... +100 VDCSignal voltage (1) 160 V ... 286 VDCVoltage via power jumper contacts 220 VDC (-20 % ... +25 %)Input current (typ.) 1.2 mA at 220 VDCInput filter 3.0 msCurrent consumption (internal) 5 mACurrent via power jumper contacts (max.) 10 A (operating temperature < 60 °C);
8 A (60°C ... 70°C operating temperature)Isolation (supply/DIN rail) Rated insulation voltage:
2.5 kV AC or 3.5 kV DCRated surge voltage: 5 kVOvervoltage category: III
Bit width 2 bitsVibration resistance acc. to IEC 60068-2-6 (acceleration: 5g),
EN 60870-2-2, IEC 60721-3-1, -3, EN 61131-2
Shock resistance acc. to IEC 60068-2-27EMC immunity of interference acc. to EN 61000-6-1, -2, EN 61131-2,
marine applications, EN 50121-3-2, -4, -5, EN 60255-26, EN 60870-2-1, EN 61850-3, IEC 61000-6-5, IEEE 1613, VDEW: 1994
EMC emission of interference acc. to EN 61000-6-3, -4, EN 61131-2, EN 60255-26, marine applications, EN 60870-2-1, EN 61850-3, EN 50121-3-2, -4, -5
750-407/040-000
750-508/040-000
5409
5
2-Channel Digital Output Module 24 VDCfor eXTReme environmental conditions; short-circuit protected, high-side switching, with diagnostics
750-508/040-000
13 14
+ +
— —
ABCD
EFGH
13 14
Data contacts
Power jumper contacts
DO 2DO 1
24 V
0 V
Status DO 2Status DO 1Error DO 2Error DO 1
270pF
100nF
10nF
10nF
10nF
μC
0 V
24 V 24 V
0 V
750-508/040-000
StatusDiag.
Status
Diagnostics
DO 1 DO 2 DO
This digital output module transmits control signals from the automation device to the connected actuators.All outputs are short-circuit proof.This output module detects the following errors: overload, short-circuit and wire break. The status is transmitted to the fieldbus coupler and indicated by LEDs.The module is a 3-conductor device.Field and system levels are electrically isolated.
The module is ideally suited for operation in harsh environmental conditions:- strongly extended temperature range - higher dielectric strength and EMC resistance- higher vibration and shock resistance
Description Item No. Pack. Unit
2DO 24VDC 2.0A/Diagnostics /XTR 750-508/040-000 1
Interference-free for use in safety functions (see manual)
Accessories Item No. Pack. Unit
Miniature WSB Quick marking systemplain 248-501 5with marking see Section 11
ApprovalsConformity marking 1
Korea CertificationMarine applications GLr UL 508 r ANSI/ISA 12.12.01 Class I, Div. 2, Grp. ABCD, T4
Technical DataWire connection CAGE CLAMP®
Cross sections 0.25 mm² ... 2.5 mm² / AWG 24 ... 14Strip lengths 8 ... 9 mm / 0.33 inDimensions (mm) W x H x L 12 x 62 x 100
Height from upper-edge of DIN 35 railWeight 48.6 gOperating temperature -40 °C ... +70 °CStorage temperature -40 °C ... +85 °CRelative humidity 95 %, short-term condensation acc. to class
3K7 / IEC EN 60721-3-3 (except wind-driven precipitation, water and ice formation)
Operating altitude without temperature derating: 0 m ... 2000 m; with temperature derating: 2000 m ... 5000 m (0.5 K/100 m); max.: 5000 m
Technical DataNo. of outputs 2Output type High-side switchingType of load Inductive, resistive loads and lampsMax. switching frequency 1 kHzOutput current (max.) 2 ACurrent consumption (internal) 14 mACurrent consumption typ. (field side) 7 mA + chargeVoltage via power jumper contacts 24 VDC
under laboratory conditions +15 °C ... +35 °C 18 V ... 31.2 V (17.4 V ... 31.2 V)1)
for -40 °C ... +55 °C 18 V ... 28.8 V (17.4 V ... 28.8 V)1)
for +55 °C ... +70 °C 18 V ... 26.4 V (17.4 V ... 26.4 V)1)
1) including residual ripple of 15 %Current via power jumper contacts (max.) 10 AIsolation (peak value) 510 VAC or 775 VDC
power supply/DIN railRated surge voltage 1 kVOvervoltage category IIIBit width 2 bitsVibration resistance acc. to IEC 60068-2-6 (acceleration: 5g),
EN 60870-2-2, IEC 60721-3-1, -3, EN 61131-2
Shock resistance acc. to IEC 60068-2-27EMC immunity of interference acc. to EN 61000-6-1, -2, EN 61131-2,
marine applications, EN 50121-3-2, -4, -5, EN 60255-26, EN 60870-2-1, EN 61850-3, IEC 61000-6-5, IEEE 1613, VDEW: 1994
EMC emission of interference acc. to EN 61000-6-3, -4, EN 61131-2, EN 60255-26, marine applications, EN 60870-2-1, EN 61850-3, EN 50121-3-2, -4, -5
750-508/040-000
750-1515/040-000
5410
8-Channel Digital Output Module 24 VDCfor eXTReme environmental conditions; high-side switching, 2-wire connection
1
1 9
2 10
3 11
4 12
5 13
6 14
7 15
8 16
2345678
750-1515/040-000
13 14
0 V
0 V
0 V
0 V
0 V
0 V
0 V
0 V
CAGE CLAMP®Sconnection
Data contacts
Power jumper contacts
StatusDO 1 ... DO 8
DO 1
DO 2
DO 3
DO 4
DO 5
DO 6
DO 7
DO 8
1
2
3
4
5
6
7
8
13
12
11
10
9
14
15
16
750-1515/040-000
DO 1
DO 2
DO 3
DO 4
DO 5
DO 6
DO 7
DO 8
0 V
+ 24 V
0 V
0 V
0 V
0 V
0 V
0 V
0 V
0 V
24 V
0 V
270 pF
10 nF
10 nF
10 nF
DO
DO
This 2-wire digital output module provides 8 channels at a width of just 12 mm.It transmits binary control signals from the automation device to the connected actuators (e.g., magnetic valves, contactors, transmitters, relays or other electrical loads).The module features CAGE CLAMP® S connections providing push-in termination of solid conductors.A green LED indicates the switched status of each channel.Field and system levels are electrically isolated.
An operating tool with a 2.5 mm blade (210-719) is required to open the CAGE CLAMP® S connections.
The module is ideally suited for operation in harsh environmental conditions:- strongly extended temperature range - higher dielectric strength and EMC resistance- higher vibration and shock resistance
Description Item No. Pack. Unit
8DO 24VDC 0.5A, 2-wire connection /XTR 750-1515/040-000 1
Interference-free for use in safety functions (see manual)
Accessories Item No. Pack. Unit
Miniature WSB Quick marking systemplain 248-501 5with marking see Section 11
Operating tool, with partially insulated shaft, type 1, blade (2.5 x 0.4) mm
210-719 50
ApprovalsConformity marking 1
Korea CertificationMarine applications GLr UL 508 r ANSI/ISA 12.12.01 Class I, Div. 2, Grp. ABCD, T4
Technical DataWire connection CAGE CLAMP® SCross sections 0.25 mm² ... 1.5 mm² / AWG 24 ... 16Strip lengths 8 ... 9 mm / 0.33 inDimensions (mm) W x H x L 12 x 62 x 100
Height from upper-edge of DIN 35 railWeight 48 gOperating temperature -40 °C ... +70 °CStorage temperature -40 °C ... +85 °CRelative humidity 95 %, short-term condensation acc. to class
3K7 / IEC EN 60721-3-3 (except wind-driven precipitation, water and ice formation)
Operating altitude without temperature derating: 0 m ... 2000 m; with temperature derating: 2000 m ... 5000 m (0.5 K/100 m); max.: 5000 m
Technical DataNo. of outputs 8Output type High-side switchingType of load Inductive, resistive loads and lampsMax. switching frequency 1 kHzOutput current (max.) 0.5 A, short-circuit protectedMax. current consumption (internal) 20 mACurrent consumption typ. (field side) 15 mAVoltage via power jumper contacts 24 VDC
under laboratory conditions +15 °C ... +35 °C 18 V ... 31.2 V (17.4 V ... 31.2 V)1)
for -40 °C ... +55 °C 18 V ... 28.8 V (17.4 V ... 28.8 V)1)
for +55 °C ... +70 °C 18 V ... 26.4 V (17.4 V ... 26.4 V)1)
1) including residual ripple of 15 %Current via power jumper contacts (max.) 10 AIsolation (peak value) 510 VAC or 775 VDC
power supply/DIN railRated surge voltage 1 kVOvervoltage category IIIBit width 8 bitsVibration resistance acc. to IEC 60068-2-6 (acceleration: 5g),
EN 60870-2-2, IEC 60721-3-1, -3, EN 61131-2
Shock resistance acc. to IEC 60068-2-27EMC immunity of interference acc. to EN 61000-6-1, -2, EN 61131-2,
marine applications, EN 50121-3-2, -4, -5, EN 60255-26, EN 60870-2-1, EN 61850-3, IEC 61000-6-5, IEEE 1613, VDEW: 1994
EMC emission of interference acc. to EN 61000-6-3, -4, EN 61131-2, EN 60255-26, marine applications, EN 60870-2-1, EN 61850-3, EN 50121-3-2, -4, -5
750-1515/040-000
750-517/040-000
5411
5
2-Channel Relay Output Module 230 VAC, 1.0 Afor eXTReme environmental conditions, potential-free, 2 changeover contacts
750-517/040-000
14 24
11 21
12 22
———— ————
ABCD
EFGH
K1 K2
Data contacts
Statusrelay 2
Status relay 1
DO 2DO 1
L 2L 1
DO 1 DO 2 ———
14
12
11
24
21
22
750-517/040-000
L
DO
DO
Status
This digital output module transmits control signals from the automation device to the connected actuators.The internal system voltage triggers the relay.The NO contacts are electrically isolated.The switched status of the relay is shown by a LED.
The module is ideally suited for operation in harsh environmental conditions:- strongly extended temperature range - higher dielectric strength and EMC resistance- higher vibration and shock resistance
Description Item No. Pack. Unit
2DO 230VAC 1.0A/ Relay 2CO/ potential-free /XTR
750-517/040-000 1
Accessories Item No. Pack. Unit
Miniature WSB Quick marking systemplain 248-501 5with marking see Section 11
ApprovalsConformity marking 1
Korea CertificationMarine applications GLr UL 508 r ANSI/ISA 12.12.01 Class I, Div. 2, Grp. ABCD, T4
Technical DataWire connection CAGE CLAMP®
Cross sections 0.25 mm² ... 2.5 mm² / AWG 24 ... 14Strip lengths 8 ... 9 mm / 0.33 inDimensions (mm) W x H x L 12 x 62 x 100
Height from upper-edge of DIN 35 railWeight 52.5 gOperating temperature -40 °C ... +70 °CStorage temperature -40 °C ... +85 °CRelative humidity 95 %, short-term condensation acc. to class
3K7 / IEC EN 60721-3-3 (except wind-driven precipitation, water and ice formation)
Operating altitude without temperature derating: 0 m ... 2000 m; with temperature derating: 2000 m ... 5000 m (0.5 K/100 m); max.: 5000 m
Technical DataNo. of outputs 2 changeover contactsMax. switching frequency 6/min (at nominal load)Pull-in time (max.) 8 msDrop-out time (max.) 4 msContact material Silver alloyMechanical life (min.) 5 x 106 (180 switching cycles/min.)Electrical life (min.) 1 x 106 (1 A AC/250 V) (resistive load)Max. switching voltage 250 VAC / 300 VDCMin. switching current 100 mA / 12 VDCMax. switching current 1A AC; 1 A at 40 VDC; 0.15 A at 300
VDCMax. current consumption (internal) 90 mAIsolation (supply/DIN rail) Rated insulation voltage:
2.5 kV AC or 3.5 kV DCRated surge voltage: 5 kVOvervoltage category: III
Internal bit width 2-bit outputVibration resistance acc. to IEC 60068-2-6 (acceleration: 5g),
EN 60870-2-2, IEC 60721-3-1, -3, EN 61131-2
Shock resistance acc. to IEC 60068-2-27EMC immunity of interference acc. to EN 61000-6-1, -2, EN 61131-2,
marine applications, EN 50121-3-2, -4, -5, EN 60255-26, EN 60870-2-1, EN 61850-3, IEC 61000-6-5, IEEE 1613, VDEW: 1994
EMC emission of interference acc. to EN 61000-6-3, -4, EN 61131-2, EN 60255-26, marine applications, EN 60870-2-1, EN 61850-3, EN 50121-3-2, -4, -5
750-517/040-000
750-453/040-000, 750-455/040-000
5412
4-Channel Analog Input Module 0/4-20 mAfor eXTReme environmental conditions; single-ended
750-453/040-000
E1 E2
M M
E3 E4
M M
ABCD
EFGH
13 14
AI 2AI 1
AI 4AI 3
Error AI 2Error AI 1Error AI 4Error AI 3
Data contacts
Common(ground)
Common(ground)
Power jumper contacts
24 V
AD
270 pF
10 nF
0 V
I
750-453/040-000
AI 2
AI 4
AI 1
Common(ground)
AI
Common(ground)
Logic
Error
AI 3
Common(ground)
The analog input module processes standard 0/4–20 mA signals.The input signal is electrically isolated and transmitted with a resolution of 12 bits.The internal system supply powers the module.The input channels of the module have a common ground potential.
The module is ideally suited for operation in harsh environmental conditions:- strongly extended temperature range - higher dielectric strength and EMC resistance- higher vibration resistance
Description Item No. Pack. Unit
4AI 0-20mA S.E. /XTR 750-453/040-000 14AI 4-20mA S.E. /XTR 750-455/040-000 1
Accessories Item No. Pack. Unit
Miniature WSB Quick marking systemplain 248-501 5with marking see Section 11
ApprovalsConformity marking 1
Korea CertificationMarine applications GLr UL 508 r ANSI/ISA 12.12.01 Class I, Div. 2, Grp. ABCD, T4
Technical DataWire connection CAGE CLAMP®
Cross sections 0.25 mm² ... 2.5 mm² / AWG 24 ... 14Strip lengths 8 ... 9 mm / 0.33 inDimensions (mm) W x H x L 12 x 62 x 100
Height from upper-edge of DIN 35 railWeight 51 gOperating temperature -40 °C ... +70 °CStorage temperature -40 °C ... +85 °CRelative humidity 95 %, short-term condensation acc. to class
3K7 / IEC EN 60721-3-3 (except wind-driven precipitation, water and ice formation)
Operating altitude without temperature derating: 0 m ... 2000 m; with temperature derating: 2000 m ... 5000 m (0.5 K/100 m); max.: 5000 m
Technical DataNumber of inputs 4Signal characteristic Single endedSignal current 0 mA ... 20 mA (750-453/040-000)
4 mA ... 20 mA (750-455/040-000)Input voltage (max.) 32 VInput resistance < 100 Ω/ 20 mAConversion time (typ.) 10 msResolution 12 bitsMeasuring error (25 °C) < ± 0.1 % of the full scale valueTemperature coefficient < ± 0.01 % / K of the full scale valueCurrent consumption (internal) 65 mAVoltage via power jumper contacts 24 VDC
under laboratory conditions +15 °C ... +35 °C 18 V ... 31.2 V (17.4 V ... 31.2 V)1)
for -40 °C ... +55 °C 18 V ... 28.8 V (17.4 V ... 28.8 V)1)
for +55 °C ... +70 °C 18 V ... 26.4 V (17.4 V ... 26.4 V)1)
1) including residual ripple of 15 %Current via power jumper contacts (max.) 10 AIsolation (peak value) 510 VAC or 775 VDC
power supply/DIN railRated surge voltage 1 kVOvervoltage category IIIBit width 4 x 16 bits data
4 x 8 bits control/status (optional)EMC immunity of interference acc. to EN 61000-6-1, -2, EN 61131-2,
marine applications, EN 50121-3-2, -4, -5, EN 60255-26, EN 60870-2-1, EN 61850-3, IEC 61000-6-5, IEEE 1613, VDEW: 1994
EMC emission of interference acc. to EN 61000-6-3, -4, EN 61131-2, EN 60255-26, marine applications, EN 60870-2-1, EN 61850-3, EN 50121-3-2, -4, -5
Vibration resistance acc. to IEC 60068-2-6 (acceleration: 5g), EN 60870-2-2, IEC 60721-3-1, -3, EN 61131-2
Shock resistance acc. to IEC 60068-2-27
750-453/040-000, 750-455/040-000
750-468/040-000
5413
5
4-Channel Analog Input Module 0-10 Vfor eXTReme environmental conditions; single-ended
750-468/040-000
E1 E2
E3 E4
M M
S S
ABCD
EFGH
13 14
Data contacts
Shield(screen)
Common(ground)
AI 2AI 1
AI 4AI 3
Function AI 2Function AI 1Function AI 4Function AI 3
270 pF
10 nF
750-468/040-000
AI 2AI 1
Shield(screen)
AI
Shield(screen)
Logic
Function
Common(ground)
Common(ground)
AI 3 AI 4
The analog input module processes standard 0–10 V signals.The input signal is electrically isolated and transmitted with a resolution of 12 bits.The internal system supply powers the module.The input channels of the module have a common ground potential.The shield (screen) is directly connected to the DIN rail.
The module is ideally suited for operation in harsh environmental conditions:- strongly extended temperature range - higher dielectric strength and EMC resistance- higher vibration and shock resistance
Description Item No. Pack. Unit
4AI 0-10V DC S.E. /XTR 750-468/040-000 1
Accessories Item No. Pack. Unit
Miniature WSB Quick marking systemplain 248-501 5with marking see Section 11
ApprovalsConformity marking 1
Korea CertificationMarine applications GLr UL 508 r ANSI/ISA 12.12.01 Class I, Div. 2, Grp. ABCD, T4
Technical DataWire connection CAGE CLAMP®
Cross sections 0.25 mm² ... 2.5 mm² / AWG 24 ... 14Strip lengths 8 ... 9 mm / 0.33 inDimensions (mm) W x H x L 12 x 62 x 100
Height from upper-edge of DIN 35 railWeight 52.5 gOperating temperature -40 °C ... +70 °CStorage temperature -40 °C ... +85 °CRelative humidity 95 %, short-term condensation acc. to class
3K7 / IEC EN 60721-3-3 (except wind-driven precipitation, water and ice formation)
Operating altitude without temperature derating: 0 m ... 2000 m; with temperature derating: 2000 m ... 5000 m (0.5 K/100 m); max.: 5000 m
Technical DataNumber of inputs 4Signal characteristic Single endedSignal voltage 0 V ... 10 VInput voltage (max.) 35 VInternal resistance 133 kΩConversion time (typ.) 4 msResolution 12 bitsMeasuring error (25 °C) < ± 0.2 % of the full scale valueTemperature coefficient < ± 0.01 % / K of the full scale valueCurrent consumption typ. (internal) 60 mAVoltage via power jumper contacts 24 VDC
under laboratory conditions +15 °C ... +35 °C 18 V ... 31.2 V (17.4 V ... 31.2 V)1)
for -40 °C ... +55 °C 18 V ... 28.8 V (17.4 V ... 28.8 V)1)
for +55 °C ... +70 °C 18 V ... 26.4 V (17.4 V ... 26.4 V)1)
1) including residual ripple of 15 %Isolation (peak value) 510 VAC or 775 VDC
power supply/DIN railRated surge voltage 1 kVOvervoltage category IIIBit width 4 x 16 bits data
4 x 8 bits control/status (optional)EMC immunity of interference acc. to EN 61000-6-1, -2, EN 61131-2,
marine applications, EN 50121-3-2, -4, -5, EN 60255-26, EN 60870-2-1, EN 61850-3, IEC 61000-6-5, IEEE 1613, VDEW: 1994
EMC emission of interference acc. to EN 61000-6-3, -4, EN 61131-2, EN 60255-26, marine applications, EN 60870-2-1, EN 61850-3, EN 50121-3-2, -4, -5
Vibration resistance acc. to IEC 60068-2-6 (acceleration: 5g), EN 60870-2-2, IEC 60721-3-1, -3, EN 61131-2
Shock resistance acc. to IEC 60068-2-27
750-468/040-000
750-457/040-000
5414
4-Channel Analog Input Module ±10 Vfor eXTReme environmental conditions; single-ended
750-457/040-000
E1 E2
M M
E3 E4
M M
ABCD
EFGH
13 14
Error AI 2Error AI 1Error AI 4Error AI 3
Data contacts
Common(ground)
Common(ground)
Power jumper contacts
AI 2AI 1
AI 4AI 3
24 V
AD
270pF
10nF
0 V
750-457/040-000
AI 2
AI 4
AI 1
Common(ground)
AI
Common(ground)
Logic
Error
AI 3
Common(ground)
This analog input module processes standard ±10 V signals.The input signal is electrically isolated and transmitted with a resolution of 12 bits.The internal system supply powers the module.The input channels of the module have a common ground potential.
The module is ideally suited for operation in harsh environmental conditions:- strongly extended temperature range - higher dielectric strength and EMC resistance- higher vibration and shock resistance
Description Item No. Pack. Unit
4AI ±10VDC S.E. /XTR 750-457/040-000 1
Accessories Item No. Pack. Unit
Miniature WSB Quick marking systemplain 248-501 5with marking see Section 11
ApprovalsConformity marking 1
Korea CertificationMarine applications GLr UL 508 r ANSI/ISA 12.12.01 Class I, Div. 2, Grp. ABCD, T4
Technical DataWire connection CAGE CLAMP®
Cross sections 0.25 mm² ... 2.5 mm² / AWG 24 ... 14Strip lengths 8 ... 9 mm / 0.33 inDimensions (mm) W x H x L 12 x 62 x 100
Height from upper-edge of DIN 35 railWeight 50.5 gOperating temperature -40 °C ... +70 °CStorage temperature -40 °C ... +85 °CRelative humidity 95 %, short-term condensation acc. to class
3K7 / IEC EN 60721-3-3 (except wind-driven precipitation, water and ice formation)
Operating altitude without temperature derating: 0 m ... 2000 m; with temperature derating: 2000 m ... 5000 m (0.5 K/100 m); max.: 5000 m
Technical DataNumber of inputs 4Signal characteristic Single endedSignal voltage ± 10 VInput voltage (max.) ± 40 VInput resistance > 100 kΩConversion time (typ.) 10 msResolution 12 bitsMeasuring error (25 °C) < ± 0.1 % of the full scale valueTemperature coefficient < ± 0.01 % / K of the full scale valueCurrent consumption (internal) 65 mAVoltage via power jumper contacts 24 VDC
under laboratory conditions +15 °C ... +35 °C 18 V ... 31.2 V (17.4 V ... 31.2 V)1)
for -40 °C ... +55 °C 18 V ... 28.8 V (17.4 V ... 28.8 V)1)
for +55 °C ... +70 °C 18 V ... 26.4 V (17.4 V ... 26.4 V)1)
1) including residual ripple of 15 %Current via power jumper contacts (max.) 10 AIsolation (peak value) 510 VAC or 775 VDC
power supply/DIN railRated surge voltage 1 kVOvervoltage category IIIBit width 4 x 16 bits data
4 x 8 bits control/status (optional)EMC immunity of interference acc. to EN 61000-6-1, -2, EN 61131-2,
marine applications, EN 50121-3-2, -4, -5, EN 60255-26, EN 60870-2-1, EN 61850-3, IEC 61000-6-5, IEEE 1613, VDEW: 1994
EMC emission of interference acc. to EN 61000-6-3, -4, EN 61131-2, EN 60255-26, marine applications, EN 60870-2-1, EN 61850-3, EN 50121-3-2, -4, -5
Vibration resistance acc. to IEC 60068-2-6 (acceleration: 5g), EN 60870-2-2, IEC 60721-3-1, -3, EN 61131-2
Shock resistance acc. to IEC 60068-2-27
750-457/040-000
750-464/040-000
5415
5
2-/4-Channel Analog Input Module for RTDsfor eXTReme environmental conditions
750-464/040-000
AB
DC
EF
HG
A1+ A2+
A1- A2-
A3+ A4+
A3- A4-
13 14
+AI 2+AI 1
−AI 2−AI 1
−AI 4−AI 3
+AI 4+AI 3
ErrorAI 2/AI 4
Function
Data contacts
ErrorAI 1/AI 3
Function
Power jumper contacts
2-channel/3-wire
2-channel/2-wire
4-channel/2-wire
24 V
AD
10 nF
0 V
MUXNTC
750-464/040-000
24 V
0 V
10nF
10nF
AI
Common(ground)
Logic
FunctionError
+AI 2+AI 1
-AI 3
+AI 3
-AI 1 -AI 2
-AI 4
+AI 4
The input module directly connects to Pt or Ni resistance sensors and potentiometers.It can be operated as a 2-channel (2- and 3-wire technology) or 4-channel (2-wire technology) module.The bus module linearizes the entire temperature range. A sensor error (short circuit, line break or measuring range overflow) is indicated by a red LED.The module can be configured via WAGO-I/O-CHECK or GSD files.The module features multiple setting options and high accuracy.
The module is ideally suited for operation in harsh environmental conditions:- strongly extended temperature range - higher dielectric strength and EMC resistance- higher vibration and shock resistance
Description Item No. Pack. Unit
2/4 AI RTD configurable /XTR 750-464/040-000 1
Accessories Item No. Pack. Unit
Miniature WSB Quick marking systemplain 248-501 5with marking see Section 11
ApprovalsConformity marking 1
Korea CertificationMarine applications GLr UL 508 r ANSI/ISA 12.12.01 Class I, Div. 2, Grp. ABCD, T4
Technical DataWire connection CAGE CLAMP®
Cross sections 0.25 mm² ... 2.5 mm² / AWG 24 ... 14Strip lengths 8 ... 9 mm / 0.33 inDimensions (mm) W x H x L 12 x 62 x 100Weight 47.3 gOperating temperature -40 °C ... +70 °CStorage temperature -40 °C ... +85 °CRelative humidity 95 %, short-term condensation acc. to class
3K7 / IEC EN 60721-3-3 (except wind-driven precipitation, water and ice formation)
Operating altitude without temperature derating: 0 m ... 2000 m; with temperature derating: 2000 m ... 5000 m (0.5 K/100 m); max.: 5000 m
EMC immunity of interference acc. to EN 61000-6-1, -2, EN 61131-2, marine applications, EN 50121-3-2, -4, -5,EN 60255-26, EN 60870-2-1, EN 61850-3, IEC 61000-6-5, IEEE 1613, VDEW: 1994
EMC emission of interference acc. to EN 61000-6-3, -4, EN 61131-2, EN 60255-26, marine applications, EN 60870-2-1, EN 61850-3, EN 50121-3-2, -4, -5
Technical DataNumber of inputs 2 / 4 (default setting)Sensor types Pt100 (default), Pt200, Pt500, Pt1000
(IEC 751), Ni100, Ni1000 (DIN 43760), Ni120 (Minco), Ni1000 (TK 5000), 2-channel operation: potentiometer, resistance measurement 10 Ω ... 5000 Ω, 10 Ω ... 1200 Ω
Sensor connection 2-conductor (default setting), 3-conductor (2-channel operation)
Measuring current (typ.) ≤ 350 μA per measurement circuitMeasurement repetition rate (standard) 1.1 sMeasurement repetition rate (2-channel/2-conductor) 0.63 sResponse time (max.) 4 sResolution 16 bits (0.1 °C)Conversion time ≤ 320 msMeasuring error (25 °C) ≤ 1 K in the entire temp. range,
≤ 0.5 K in the restricted temp. range (-30 °C ... +120 °C)
Accuracy (+25 °C) ≤ ± 0.2% of full scale value; typ.: ≤ ± 0.1% of full scale value
Temperature coefficient ≤ 20 ppm/K; typ. ≤ 15 ppm/KCurrent consumption typ. (internal) 50 mAVoltage via power jumper contacts 24 VDC
under laboratory conditions +15 °C ... +35 °C 18 V ... 31.2 V (17.4 V ... 31.2 V)1)
for -40 °C ... +55 °C 18 V ... 28.8 V (17.4 V ... 28.8 V)1)
for +55 °C ... +70 °C 18 V ... 26.4 V (17.4 V ... 26.4 V)1)
1) including residual ripple of 15 %Current via power jumper contacts (max.) 10 AIsolation (peak value) 510 VAC or 775 VDC power supply/DIN railRated surge voltage 1 kVOvervoltage category IIIBit width 4 (2) x 16 bits data
4 (2) x 8 bits control/status (option)Vibration resistance acc. to IEC 60068-2-6 (acceleration: 5g),
EN 60870-2-2, IEC 60721-3-1, -3, EN 61131-2Shock resistance acc. to IEC 60068-2-27
750-464/040-000
750-469/040-000
5416
2-Channel Analog Input Module for Thermocouplesfor eXTReme environmental conditions
750-469/040-000
+TC +TC
—TC —TC
M M
S S
ABCD
EFGH
13 14
Data contacts
Error AI 2
Shield(screen)
Common(ground)
Function AI 2Function AI 1Error AI 1
+TC 1
-TC 1
+TC 2
-TC 2 270 pF
20 nF
270 pF
JVGL
750-469/040-000
+TC 2+TC 1
Shield(screen)
+TC
Shield(screen)
Logic
FunctionCommon(ground)
-TC 1 -TC 2 -TC
Common(ground)
Error
This input module directly connects to two thermocouples. Internal electrical isolation allows operation of grounded sensors.The bus module linearizes the entire temperature range.Cold junction compensation mitigates the clamping unit offset voltage over the 0–55°C operating range. A line break is indicated by a red LED. A green LED indicates readiness for operation and error-free communication with the bus coupler.The shield (screen) is directly connected to the DIN rail.
The module is ideally suited for operation in harsh environmental conditions:- strongly extended temperature range - higher dielectric strength and EMC resistance- higher vibration and shock resistance
Description Item No. Pack. Unit
2AI Thermocouple/configurable /XTR 750-469/040-000 1
Accessories Item No. Pack. Unit
Miniature WSB Quick marking systemplain 248-501 5with marking see Section 11
ApprovalsConformity marking 1
Korea CertificationMarine applications GLr UL 508 r ANSI/ISA 12.12.01 Class I, Div. 2, Grp. ABCD, T4
Technical DataWire connection CAGE CLAMP®
Cross sections 0.25 mm² ... 2.5 mm² / AWG 24 ... 14Strip lengths 8 ... 9 mm / 0.33 inDimensions (mm) W x H x L 12 x 62 x 100; Height from upper-edge of DIN 35 railWeight 38.2 gOperating temperature -40 °C ... +70 °CStorage temperature -40 °C ... +85 °CRelative humidity 95 %, short-term condensation acc. to class
3K7 / IEC EN 60721-3-3 (except wind-driven precipitation, water and ice formation)
Operating altitude without temperature derating: 0 m ... 2000 m; with temperature derating: 2000 m ... 5000 m (0.5 K/100 m); max.: 5000 m
EMC immunity of interference acc. to EN 61000-6-1, -2, EN 61131-2, marine applications, EN 50121-3-2, -4, -5, EN 60255-26, EN 60870-2-1, EN 61850-3, IEC 61000-6-5, IEEE 1613, VDEW: 1994
EMC emission of interference acc. to EN 61000-6-3, -4, EN 61131-2, EN 60255-26, marine applications, EN 60870-2-1, EN 61850-3, EN 50121-3-2, -4, -5
Technical DataNumber of inputs 2Sensor types Type L: -100°C ... +900°C;
Type K: -100°C ... +1370°C; Type J: -100°C ... +1200°C; Type E: -100°C ... +1000°C; Type T: -100°C ... +400°C; Type N: -100°C ... +1300°C; Type U: -25°C ... +600°C; Type B: +600°C ... +1800°C; Type R: 0°C ... +1700°C; Type S: -50°C ... +1700°C; -30 mV ... +30 mV; -60 mV ... +60 mV; -120 mV ... +120 mV
Internal resistance 1 MΩCold junction compensation at each pair of terminal blocksResolution (over entire range) 0.1 °CConversion time 320 ms (each channel)Measuring error (25 °C) < ± 6 K (volt. input < ± 2 K,
cold junct. < ± 4 K)Temperature coefficient < ± 0.2 K/KMax. admissible current between the ground contacts 3 and 7: 100 mAMax. current consumption (internal) 65 mAVoltage via power jumper contacts 24 VDC
under laboratory conditions +15 °C ... +35 °C 18 V ... 31.2 V (17.4 V ... 31.2 V)1)
for -40 °C ... +55 °C 18 V ... 28.8 V (17.4 V ... 28.8 V)1)
for +55 °C ... +70 °C 18 V ... 26.4 V (17.4 V ... 26.4 V)1)
1) including residual ripple of 15 %Isolation (peak value) 510 VAC or 775 VDC power supply/DIN railRated surge voltage 1 kVOvervoltage category IIIBit width 2 x 16 bits data
2 x 8 bits control/status (optional)Vibration resistance acc. to IEC 60068-2-6 (acceleration: 5g),
EN 60870-2-2, IEC 60721-3-1, -3, EN 61131-2Shock resistance acc. to IEC 60068-2-27
750-469/040-000
750-563/040-000
5417
5
2-Channel Analog Output Module, 0/4 ... 20 mA / 6 ... 18 VDCfor eXTReme environmental conditions; 16-bit, configurable
750-563/040-000
A1+ A2–
M M
S1+ S2+
S1– S2–
ABCD
EFGH
13 14
Data contacts
Common(ground)Power jumper contacts
+AO 2+AO 1
− Sense AO 2− Sense AO 1
Function AO 1Error AO 1
+ Sense AO 2+ Sense AO 1
Function AO 2Error AO 2
1
2
3
4
5
6
7
8
+ 24 V
0 V
+24 V
0 V
100 nF
10 nF 10 nF
AD
IU
0...20mA
6...18V
750-563/040-000
+ AO 1
Common(ground)
Common(ground)
+ Sense AO 1
- Sense AO 1
+ Sense AO 2
- Sense AO 2
+ AO 2 AO
Function Error
Common(ground)
Logic
This analog output module generates 0/4–20 mA output currents or 6–18 V output voltages for the field.Output ranges can be configured via WAGO-I/O-CHECK or GSD files.The module has two short-circuit-proof output channels and enables direct connection of two 2-wire actuators to AO 1 and ground or AO2 and ground. Signals are output via AO 1 or AO 2. In addition, the sense lines from 4-wire actuators can be connected to -Sense AO1 and +Sense AO1 or -Sense AO2 and +Sense AO2.Both output channels have a common ground potential.
The output signal is electrically isolated and transmitted with a resolution of 16 bits.Both internal system and field side supply power the module.
The module is ideally suited for operation in harsh environmental conditions:- strongly extended temperature range - higher dielectric strength and EMC resistance- higher vibration and shock resistance
Description Item No. Pack. Unit
2 AO 0/4-20mA / 6-18VDC configurable /XTR
750-563/040-000 1
Accessories Item No. Pack. Unit
Miniature WSB Quick marking systemplain 248-501 5with marking see Section 11
ApprovalsConformity marking 1
Korea CertificationMarine applications GLr UL 508 r ANSI/ISA 12.12.01 Class I, Div. 2, Grp. ABCD, T4
Technical DataWire connection CAGE CLAMP®
Cross sections 0.25 mm² ... 2.5 mm² / AWG 24 ... 14Strip lengths 8 ... 9 mm / 0.33 inDimensions (mm) W x H x L 12 x 62 x 100
Height from upper-edge of DIN 35 railWeight 53.5 gOperating temperature -40 °C ... +70 °CStorage temperature -40 °C ... +85 °CRelative humidity 95 %, short-term condensation acc. to class
3K7 / IEC EN 60721-3-3 (except wind-driven precipitation, water and ice formation)
Operating altitude without temperature derating: 0 m ... 2000 m; with temperature derating: 2000 m ... 5000 m (0.5 K/100 m); max.: 5000 m
Vibration resistance acc. to IEC 60068-2-6 (acceleration: 5g), EN 60870-2-2, IEC 60721-3-1, -3, EN 61131-2
Shock resistance acc. to IEC 60068-2-27
Technical DataNo. of outputs 2Operation modes configurable:
0 mA ... 20 mA; 4 mA ... 20 mA; 6 V ... 18 V
Load impedance > 1.8 kΩ (voltage output) < 500 Ω (current output)
Resolution 16 bitsConversion time (typ.) 5 msRecovery time (typ.) < 300μsMeasuring error (25 °C) < ± 0.05 % of the scale end valueTemperature coefficient < ± 100 ppmCurrent consumption (internal) 80 mA ... 110 mAVoltage via power jumper contacts 24 VDC
under laboratory conditions +15 °C ... +35 °C min. ... 31.2 V1)
for -40 °C ... +55 °C min. ... 28.8 V1)
for +55 °C ... +70 °C min. ... 26.4 V1)
min. voltage range: 21.6 V (24 V - 10 %); min. current range: 20.4 V (24 V - 15 %); 1) including residual ripple of 15 %
Current via power jumper contacts (max.) 10 AIsolation (peak value) 510 VAC or 775 VDC
power supply/DIN railRated surge voltage 1 kVOvervoltage category IIIBit width 2 x 16 bits data
2 x 8 bits control/status (optional)EMC immunity of interference acc. to EN 61000-6-1, -2, EN 61131-2,
marine applications, EN 50121-3-2, -4, -5, EN 60255-26, EN 60870-2-1, EN 61850-3, IEC 61000-6-5, IEEE 1613, VDEW: 1994
EMC emission of interference acc. to EN 61000-6-3, -4, EN 61131-2, EN 60255-26, marine applications, EN 60870-2-1, EN 61850-3, EN 50121-3-2, -4, -5
750-563/040-000
750-557/040-000, 750-559/040-000
5418
4-Channel Analog Output Module ±10 V/0-10 Vfor eXTReme environmental conditions
750-557/040-000
A1 A2
M M
A3 A4
M M
ABCD
EFGH
13 14
Data contacts
Common(ground)
Common(ground)
Function
Power jumper contacts
Error
AO 2AO 1
AO 4AO 3
24 V 220 nF
10nF
0 V
750-557/040-000
AO 2AO 1
Common(ground)
AO
Common(ground)
Function
AO 4
Logic
Common(ground)
AO 3
This analog output module generates standard ±10 V or 0–10 V signals.The output signal is electrically isolated and transmitted with a resolution of 12 bits.The internal system supply powers the module.The output channels of the module have a common ground potential.
The module is ideally suited for operation in harsh environmental conditions:- strongly extended temperature range - higher dielectric strength and EMC resistance- higher vibration and shock resistance
Description Item No. Pack. Unit
4AO ± 10VDC /XTR 750-557/040-000 14AO 0-10VDC /XTR 750-559/040-000 1
Accessories Item No. Pack. Unit
Miniature WSB Quick marking systemplain 248-501 5with marking see Section 11
ApprovalsConformity marking 1
Korea CertificationMarine applications GLr UL 508 r ANSI/ISA 12.12.01 Class I, Div. 2, Grp. ABCD, T4
Technical DataWire connection CAGE CLAMP®
Cross sections 0.25 mm² ... 2.5 mm² / AWG 24 ... 14Strip lengths 8 ... 9 mm / 0.33 inDimensions (mm) W x H x L 12 x 62 x 100
Height from upper-edge of DIN 35 railWeight 53.5 gOperating temperature -40 °C ... +70 °CStorage temperature -40 °C ... +85 °CRelative humidity 95 %, short-term condensation acc. to class
3K7 / IEC EN 60721-3-3 (except wind-driven precipitation, water and ice formation)
Operating altitude without temperature derating: 0 m ... 2000 m; with temperature derating: 2000 m ... 5000 m (0.5 K/100 m); max.: 5000 m
Technical DataNo. of outputs 4Signal voltage ±10 V (750-557/040-000)
0 V ... 10 V (750-559/040-000)Load impedance > 5 kΩResolution 12 bitsConversion time (typ.) 10 msRecovery time (typ.) 100msMeasuring error (25 °C) < ± 0.1 % of the full scale valueTemperature coefficient < ± 0.01 % / K of the full scale valueMax. current consumption (internal) 125 mAVoltage via power jumper contacts 24 V DC
under laboratory conditions +15 °C ... +35 °C 18 V ... 31.2 V (17.4 V ... 31.2 V)1)
for -40 °C ... +55 °C 18 V ... 28.8 V (17.4 V ... 28.8 V)1)
for +55 °C ... +70 °C 18 V ... 26.4 V (17.4 V ... 26.4 V)1)
1) including residual ripple of 15 %Current via power jumper contacts (max.) 10 AIsolation (peak value) 510 VAC or 775 VDC
power supply/DIN railRated surge voltage 1 kVOvervoltage category IIIBit width 4 x 16 bits data
4 x 8 bits control/status (optional)Vibration resistance acc. to IEC 60068-2-6 (acceleration: 5g),
EN 60870-2-2, IEC 60721-3-1, -3, EN 61131-2Shock resistance acc. to IEC 60068-2-27EMC immunity of interference acc. to EN 61000-6-1, -2, EN 61131-2,
marine applications, EN 50121-3-2, -4, -5, EN 60255-26, EN 60870-2-1, EN 61850-3, IEC 61000-6-5, IEEE 1613, VDEW: 1994
EMC emission of interference acc. to EN 61000-6-3, -4, EN 61131-2, EN 60255-26, marine applications, EN 60870-2-1, EN 61850-3, EN 50121-3-2, -4, -5
750-557/040-000, 750-559/040-000
750-652/040-000
5419
5
Serial Interface RS-232 / RS-485for eXTReme environmental conditions; freely configurable
750-652/040-000
13 14AB
DC
EF
HG
D0 D1
D2 D3
M M
S S
TxD (RS-232)Y (RS-485/422)
RS ... enabledFlow control enabledUser LED 1User LED 0Data contacts
FunctionTransmission status
Reception statusError (buffer full)
RTS (RS-232)Z (RS-485/422)
CTS (RS-232)B (RS-485/422)
Power jumper contacts
Common(ground)
RxD (RS-232)A (RS-485/422)
Shield(screen)
4 x 270pF
10 nF
1 MΩ
24 V
0 V
750-652/040-000
Shield(screen)
Shield(screen)
Logic
Reception Transmission
Operating mode(RS-232/-485)Flow controlFunction
Common(ground) Common
(ground)
TxD/YRTS/Z
RxD/A
CTS/B RTS/Z
TxD/Y
RxD/A
CTS/B
This serial interface module connects RS-485, RS-422 or RS-232 interface devices to the WAGO-I/O-SYSTEM 750. It also provides gateways between the serial interface and the fieldbus systems supported by the WAGO-I/O-SYSTEM 750. No higher protocol level is required by the module. Communication is completely transparent to the fieldbus master, which provides a wide range of applications for the serial interface module. If required, communication protocols can be configured via fieldbus master.The 2560-byte input buffer provides for high data baud rates. At lower baud rates, the data received in lower priority tasks is evaluated without data loss.
The 512-byte output buffer provides fast transmission of larger data strings.The module can be configured via WAGO-I/O-CHECK or GSD files. Flexible baud rate and data width selection provides perfect adaptation to the respective applicationThe module is ideally suited for operation in harsh environmental conditions:- strongly extended temperature range - higher dielectric strength and EMC resistance- higher vibration and shock resistance
Description Item No. Pack. Unit
RS-232/RS-485 freely configurable /XTR 750-652/040-000 1
Accessories Item No. Pack. Unit
Miniature WSB Quick marking systemplain 248-501 5with marking see Section 11
ApprovalsConformity marking 1
Korea CertificationMarine applications GLr UL 508 r ANSI/ISA 12.12.01 Class I, Div. 2, Grp. ABCD, T4
Technical DataWire connection CAGE CLAMP®
Cross sections 0.25 mm² ... 2.5 mm² / AWG 24 ... 14Strip lengths 8 ... 9 mm / 0.33 inDimensions (mm) W x H x L 12 x 62 x 100
Height from upper-edge of DIN 35 railWeight 51 gOperating temperature -40 °C ... +70 °CStorage temperature -40 °C ... +85 °CRelative humidity 95 %, short-term condensation acc. to class
3K7 / IEC EN 60721-3-3 (except wind-driven precipitation, water and ice formation)
Operating altitude without temperature derating: 0 m ... 2000 m; with temperature derating: 2000 m ... 5000 m (0.5 K/100 m); max.: 5000 m
Technical DataTransmission channels 1 TxD / 1 RxD, full duplex, half duplex 7 or
8 bit data, 1 or 2 stop bitBaud rate 9,600 baud (default setting)
300 baud ... 115,200 baudBit transfer RS-485/-422: ISO 8482 /
DIN 66259 - 4; RS-232: EIA/TIA-232-FLine length RS-485/-422: max. approx. 1000 m,
RS-232: max. 40 m, data exchange mode/DMX: max. 100 m twisted-pair cable
Buffer 2560 bytes for reception / 512 bytes for transmission
Internal bit width 8, 24 or 48 bytes (parametrizable)Current consumption (internal) 85 mAVoltage via power jumper contacts 24 VDC
under laboratory conditions +15 °C ... +35 °C 18 V ... 31.2 V (17.4 V ... 31.2 V)1)
for -40 °C ... +55 °C 18 V ... 28.8 V (17.4 V ... 28.8 V)1)
for +55 °C ... +70 °C 18 V ... 26.4 V (17.4 V ... 26.4 V)1)
1) including residual ripple of 15 %Current via power jumper contacts (max.) 10 AIsolation (peak value) 510 VAC or 775 VDC
power supply/DIN railRated surge voltage 1 kVOvervoltage category IIIEMC immunity of interference acc. to EN 61000-6-1, -2, EN 61131-2,
marine applications, EN 50121-3-2, -4, -5, EN 60255-26, EN 60870-2-1, EN 61850-3, IEC 61000-6-5, IEEE 1613, VDEW: 1994
EMC emission of interference acc. to EN 61000-6-3, -4, EN 61131-2, EN 60255-26, marine applications, EN 60870-2-1, EN 61850-3, EN 50121-3-2, -4, -5
Vibration resistance acc. to IEC 60068-2-6 (acceleration: 5g), EN 60870-2-2, IEC 60721-3-1, -3, EN 61131-2
Shock resistance acc. to IEC 60068-2-27
750-652/040-000
750-602/040-000
5420
Supply Module 24 VDCfor eXTReme environmental conditions; passive
750-602/040-000
+ +
— —
ABCD
EFGH
13 14
Data contacts
Power jumper contacts
0 V
Supply viapower jumper contacts24 V
Status voltage supply-Power jumper contacts
0 V
24 V24 V
0 V
750-602/040-000
1 MΩ 10 nF
10 nF
10 nF
Status
This supply module provides the I/O modules with the corresponding supply potential.Maximum available supply current to all connected modules is 10 A. When configuring the system, it must be ensured that this total current is not exceeded.Should higher currents be necessary, an intermediate supply module must be added to the assembly.
The module is ideally suited for operation in harsh environmental conditions:- strongly extended temperature range - higher dielectric strength and EMC resistance- higher vibration and shock resistance
Description Item No. Pack. Unit
24VDC Power Supply /XTR 750-602/040-000 1
Accessories Item No. Pack. Unit
Miniature WSB Quick marking systemplain 248-501 5with marking see Section 11
ApprovalsConformity marking 1
Korea CertificationMarine applications GLr UL 508 r ANSI/ISA 12.12.01 Class I, Div. 2, Grp. ABCD, T4
Technical DataWire connection CAGE CLAMP®
Cross sections 0.25 mm² ... 2.5 mm² / AWG 24 ... 14Strip lengths 8 ... 9 mm / 0.33 inDimensions (mm) W x H x L 12 x 62 x 100
Height from upper-edge of DIN 35 railWeight 44.1 gOperating temperature -40 °C ... +70 °CStorage temperature -40 °C ... +85 °CRelative humidity 95 %, short-term condensation acc. to class 3K7
/ IEC EN 60721-3-3 (except wind-driven precipitation, water and ice formation)
Operating altitude without temperature derating: 0 m ... 2000 m; with temperature derating: 2000 m ... 5000 m (0.5 K/100 m); max.: 5000 m
Technical DataVoltage via power jumper contacts 24 VDC
under laboratory conditions +15 °C ... +35 °C 18 V ... 31.2 V (17.4 V ... 31.2 V)1)
for -40 °C ... +55 °C 18 V ... 28.8 V (17.4 V ... 28.8 V)1)
for +55 °C ... +70 °C 18 V ... 26.4 V (17.4 V ... 26.4 V)1)
1) including residual ripple of 15 %Current via power jumper contacts (max.) 10 AIsolation (peak value) 510 VAC or 775 VDC
power supply/DIN railRated surge voltage 1 kVOvervoltage category IIIVibration resistance acc. to IEC 60068-2-6 (acceleration: 5g),
EN 60870-2-2, IEC 60721-3-1, -3, EN 61131-2
Shock resistance acc. to IEC 60068-2-27EMC immunity of interference acc. to EN 61000-6-1, -2, EN 61131-2,
marine applications, EN 50121-3-2, -4, -5, EN 60255-26, EN 60870-2-1, EN 61850-3, IEC 61000-6-5, IEEE 1613, VDEW: 1994
EMC emission of interference acc. to EN 61000-6-3, -4, EN 61131-2, EN 60255-26, marine applications, EN 60870-2-1, EN 61850-3, EN 50121-3-2, -4, -5
750-612/040-000
5421
5
Supply Module 230 V AC/DCfor eXTReme environmental conditions; passive
750-612/040-000
+ +
— —
ABCD
EFGH
13 14
Data contacts
Power jumper contacts
0 V
Supply viapower jumper contacts0 ... 230 V 0 ... 230 V
0 V 0 V
0 ... 230 V
750-612/040-000
470 pF
470 pF
470 pF
This supply module provides the I/O modules with the corresponding supply potential.Maximum available supply current to all connected modules is 10 A. When configuring the system, it must be ensured that this total current is not exceeded.Should higher currents be necessary, an intermediate supply module must be added to the assembly.
The module is ideally suited for operation in harsh environmental conditions:- strongly extended temperature range - higher dielectric strength and EMC resistance- higher vibration and shock resistance
Description Item No. Pack. Unit
0-230V AC/DC Power Supply /XTR 750-612/040-000 1
Accessories Item No. Pack. Unit
Miniature WSB Quick marking systemplain 248-501 5with marking see Section 11
ApprovalsConformity marking 1
Korea CertificationMarine applications GLr UL 508 r ANSI/ISA 12.12.01 Class I, Div. 2, Grp. ABCD, T4
Technical DataWire connection CAGE CLAMP®
Cross sections 0.25 mm² ... 2.5 mm² / AWG 24 ... 14Strip lengths 8 ... 9 mm / 0.33 inDimensions (mm) W x H x L 12 x 62 x 100
Height from upper-edge of DIN 35 railWeight 51.5 gOperating temperature -40 °C ... +70 °CStorage temperature -40 °C ... +85 °CRelative humidity 95 %, short-term condensation acc. to class 3K7
/ IEC EN 60721-3-3 (except wind-driven precipitation, water and ice formation)
Operating altitude without temperature derating: 0 m ... 2000 m; with temperature derating: 2000 m ... 5000 m (0.5 K/100 m); max.: 5000 m
Technical DataVoltage via power jumper contacts 0 V ... 230 V AC/DC (-20 % ... +25 %)Current via power jumper contacts (max.) 10 A DCIsolation (supply/DIN rail) Rated insulation voltage:
2.5 kV AC or 3.5 kV DCRated surge voltage: 5 kVOvervoltage category: III
Vibration resistance acc. to IEC 60068-2-6 (acceleration: 5g), EN 60870-2-2, IEC 60721-3-1, -3, EN 61131-2
Shock resistance acc. to IEC 60068-2-27EMC immunity of interference acc. to EN 61000-6-1, -2, EN 61131-2,
marine applications, EN 50121-3-2, -4, -5, EN 60255-26, EN 60870-2-1, EN 61850-3, IEC 61000-6-5, IEEE 1613, VDEW: 1994
EMC emission of interference acc. to EN 61000-6-3, -4, EN 61131-2, EN 60255-26, marine applications, EN 60870-2-1, EN 61850-3, EN 50121-3-2, -4, -5
750-613/040-000
5422
Internal System Supply Module 24 VDCfor eXTReme environmental conditions
750-613/040-000
+ +
— —
24V 0V
ABCD
EFGH
13 14
Data contacts
Power jumper contacts
0 V
Supply viapower jumper contacts24 V
Supply24 V0 V
Status voltage supply-System-Power jumper contacts
0 V
24 V24 V
0 V
750-613/040-000
10 nF
10 nF
10 nF
47 nF 47 nF
0 V24 V
24 V
0 V
2/6
3/7
I/O modulesStatus
Status
This internal system supply module increases the current supply for the internal system by 2 A.If the internal current consumption of all modules is higher than 2 A, an additional supply module must be added.The module also supplies field side power to the adjoining modules via the power jumper contacts.
The module is ideally suited for operation in harsh environmental conditions:- strongly extended temperature range - higher dielectric strength and EMC resistance- higher vibration and shock resistance
Description Item No. Pack. Unit
24VDC Bus Power Supply /XTR 750-613/040-000 1
Accessories Item No. Pack. Unit
Miniature WSB Quick marking systemplain 248-501 5with marking see Section 11
ApprovalsConformity marking 1
Korea CertificationMarine applications GLr UL 508 r ANSI/ISA 12.12.01 Class I, Div. 2, Grp. ABCD, T4
Technical DataWire connection CAGE CLAMP®
Cross sections 0.25 mm² ... 2.5 mm² / AWG 24 ... 14Strip lengths 8 ... 9 mm / 0.33 inDimensions (mm) W x H x L 12 x 62 x 100
Height from upper-edge of DIN 35 railWeight 58.5 gOperating temperature -40 °C ... +70 °CStorage temperature -40 °C ... +85 °CRelative humidity 95 %, short-term condensation acc. to class 3K7
/ IEC EN 60721-3-3 (except wind-driven precipitation, water and ice formation)
Operating altitude without temperature derating: 0 m ... 2000 m; with temperature derating: 2000 m ... 5000 m (0.5 K/100 m); max.: 5000 m
Technical DataInput current max. 500 mATotal current for I/O modules 2000 mAVoltage via power jumper contacts 24 VDC
under laboratory conditions +15 °C ... +35 °C 18 V ... 31.2 V (17.4 V ... 31.2 V)1)
for -40 °C ... +55 °C 18 V ... 28.8 V (17.4 V ... 28.8 V)1)
for +55 °C ... +70 °C 18 V ... 26.4 V (17.4 V ... 26.4 V)1)
1) including residual ripple of 15 %Current via power jumper contacts (max.) 10 AIsolation (peak value) 510 VAC or 775 VDC
power supply/DIN railRated surge voltage 1 kVOvervoltage category IIIVibration resistance acc. to IEC 60068-2-6 (acceleration: 5g),
EN 60870-2-2, IEC 60721-3-1, -3, EN 61131-2
Shock resistance acc. to IEC 60068-2-27EMC immunity of interference acc. to EN 61000-6-1, -2, EN 61131-2,
marine applications, EN 50121-3-2, -4, -5, EN 60255-26, EN 60870-2-1, EN 61850-3, IEC 61000-6-5, IEEE 1613, VDEW: 1994
EMC emission of interference acc. to EN 61000-6-3, -4, EN 61131-2, EN 60255-26, marine applications, EN 60870-2-1, EN 61850-3, EN 50121-3-2, -4, -5
750-624/040-001
5423
5
Field-Side Power Supply Filterfor eXTReme environmental conditions; for field-side power supply
750-624/040-001
+ +
— —
ABCD
EFGH
13 14
Data contacts
Power jumper contacts
0 V
Supply viapower jumper contacts24 V
Status voltage supply-Power jumper contacts
24 V
0 V
24 V
0 V
750-624/040-001
10 nF
10 nF 1 MΩ
2/6
3/7
The WAGO-I/O-SYSTEM 750 XTR can also be used in shipbuilding applications and onshore/offshore installations (e.g., platforms, loading facilities). This is possible via certification under the standards of leading agencies such as Germanischer Lloyd and Lloyds Register. Proper system operation is ensured (certified) by using this overvoltage protection module. This also applies to XTR I/O modules used in substations and/or telecontrol systems. The following modules are required for power supply: 750-626/040-000 Power Supply Filter (system and field supply) or 750-624/040-001 Field-Side Power Supply Filter (only field supply).WAGO's 750-624/040-001 Field-Side Power Supply Filter is equipped with surge suppression and can also be used as a power supply module.
The module is ideally suited for operation in harsh environmental conditions:- strongly extended temperature range - higher dielectric strength and EMC resistance- higher vibration and shock resistance
Description Item No. Pack. Unit
24VDC Field-Side Power Supply Filter with Overvoltage (Surge) Protection /XTR
750-624/040-001 1
Accessories Item No. Pack. Unit
Miniature WSB Quick marking systemplain 248-501 5with marking see Section 11
ApprovalsConformity marking 1
Korea CertificationMarine applications GLr UL 508 r ANSI/ISA 12.12.01 Class I, Div. 2, Grp. ABCD, T4
Technical DataWire connection CAGE CLAMP®
Cross sections 0.25 mm² ... 2.5 mm² / AWG 24 ... 14Strip lengths 8 ... 9 mm / 0.33 inDimensions (mm) W x H x L 12 x 62 x 100
Height from upper-edge of DIN 35 railWeight 51 gOperating temperature -40 °C ... +70 °CStorage temperature -40 °C ... +85 °CRelative humidity 95 %, short-term condensation acc. to class 3K7
/ IEC EN 60721-3-3 (except wind-driven precipitation, water and ice formation)
Operating altitude without temperature derating: 0 m ... 2000 m; with temperature derating: 2000 m ... 5000 m (0.5 K/100 m); max.: 5000 m
Technical DataVoltage via power jumper contacts 24 VDC
under laboratory conditions +15 °C ... +35 °C 18 V ... 31.2 V (17.4 V ... 31.2 V)1)
for -40 °C ... +55 °C 18 V ... 28.8 V (17.4 V ... 28.8 V)1)
for +55 °C ... +70 °C 18 V ... 26.4 V (17.4 V ... 26.4 V)1)
1) including residual ripple of 15 %Current via power jumper contacts (max.) 10 AIsolation (peak value) 510 VAC or 775 VDC
power supply/DIN railRated surge voltage 1 kVOvervoltage category IIIVibration resistance acc. to IEC 60068-2-6 (acceleration: 5g),
EN 60870-2-2, IEC 60721-3-1, -3, EN 61131-2
Shock resistance acc. to IEC 60068-2-27EMC immunity of interference acc. to EN 61000-6-1, -2, EN 61131-2,
marine applications, EN 50121-3-2, -4, -5, EN 60255-26, EN 60870-2-1, EN 61850-3, IEC 61000-6-5, IEEE 1613, VDEW: 1994
EMC emission of interference acc. to EN 61000-6-3, -4, EN 61131-2, EN 60255-26, marine applications, EN 60870-2-1, EN 61850-3, EN 50121-3-2, -4, -5
750-626/040-000
5424
Power Supply Filterfor eXTReme environmental conditions; for system and field-side power supply
750-626/040-000
+ +
— —
—+
+ —
ABCD
EFGH
13 14
Data contacts
System power supply (Out)24 V0 V
Supply viapower jumper contacts24 V
Status voltage supply-System-Power jumper contacts
Power jumper contacts
0 V
System power supply (In)24 V0 V
0 V/OUT24 V/OUT
24 V/IN
24 V/OUT
24 V/IN
0 V/IN
0 V
24 V
24 V
0 V/OUT
0 V
0 V/IN750-626/040-000
10 nF 10 nF
10 nF
10 nF
1 MΩ
1 MΩ
2/6
3/7
51
4
8
The WAGO-I/O-SYSTEM 750 XTR can also be used in shipbuilding applications and onshore/offshore installations (e.g., platforms, loading facilities). This is possible via certification under the standards of leading agencies such as Germanischer Lloyd and Lloyds Register. Proper system operation is ensured (certified) by using this overvoltage protection module. This also applies to XTR I/O modules used in substations and/or telecontrol systems. The following modules are required for power supply: 750-626/040-000 Power Supply Filter (system and field supply) or 750-624/040-001 Field-Side Power Supply Filter (only field supply).WAGO's 750-626/040-000 Power Supply Filter filters the 24 V system power supply and is equipped with surge suppression. The power supply filter can also be used as a power supply module.
The module is ideally suited for operation in harsh environmental conditions:- strongly extended temperature range - higher dielectric strength and EMC resistance- higher vibration and shock resistance
Description Item No. Pack. Unit
24VDC Power Supply Filter with Overvoltage (Surge) Protection /XTR
750-626/040-000 1
Accessories Item No. Pack. Unit
Miniature WSB Quick marking systemplain 248-501 5with marking see Section 11
ApprovalsConformity marking 1
Korea CertificationMarine applications GLr UL 508 r ANSI/ISA 12.12.01 Class I, Div. 2, Grp. ABCD, T4
Technical DataWire connection CAGE CLAMP®
Cross sections 0.25 mm² ... 2.5 mm² / AWG 24 ... 14Strip lengths 8 ... 9 mm / 0.33 inDimensions (mm) W x H x L 12 x 62 x 100
Height from upper-edge of DIN 35 railWeight 51 gOperating temperature -40 °C ... +70 °CStorage temperature -40 °C ... +85 °CRelative humidity 95 %, short-term condensation acc. to class 3K7
/ IEC EN 60721-3-3 (except wind-driven precipitation, water and ice formation)
Operating altitude without temperature derating: 0 m ... 2000 m; with temperature derating: 2000 m ... 5000 m (0.5 K/100 m); max.: 5000 m
Technical DataVoltage via power jumper contacts 24 VDC
under laboratory conditions +15 °C ... +35 °C 18 V ... 31.2 V (17.4 V ... 31.2 V)1)
for -40 °C ... +55 °C 18 V ... 28.8 V (17.4 V ... 28.8 V)1)
for +55 °C ... +70 °C 18 V ... 26.4 V (17.4 V ... 26.4 V)1)
1) including residual ripple of 15 %Current via system voltage (max.) 1.5 ACurrent via power jumper contacts (max.) 10 AIsolation (peak value) 510 VAC or 775 VDC
power supply/DIN railRated surge voltage 1 kVOvervoltage category IIIVibration resistance acc. to IEC 60068-2-6 (acceleration: 5g),
EN 60870-2-2, IEC 60721-3-1, -3, EN 61131-2
Shock resistance acc. to IEC 60068-2-27EMC immunity of interference acc. to EN 61000-6-1, -2, EN 61131-2,
marine applications, EN 50121-3-2, -4, -5, EN 60255-26, EN 60870-2-1, EN 61850-3, IEC 61000-6-5, IEEE 1613, VDEW: 1994
EMC emission of interference acc. to EN 61000-6-3, -4, EN 61131-2, EN 60255-26, marine applications, EN 60870-2-1, EN 61850-3, EN 50121-3-2, -4, -5
750-1605/040-000
5425
5
Field-Side Connection Module 16+for eXTReme environmental conditions; 24 VDC
1 9
2 10
3 11
4 12
5 13
6 14
7 15
8 16
750-1605/040-000
13 14
24 V
24 V
24 V
24 V
24 V
24 V
24 V
24 V
24 V
24 V
24 V
24 V
24 V
24 V
24 V
24 V
CAGE CLAMP®Sconnection
Data contacts
Power jumper contacts
1
2
3
4
5
6
7
8
13
12
11
10
9
14
15
16
+
+
+
+
+
+
+
+
0 V
+ 24 V
+
+
+
+
+
+
+
+
750-1605/040-000
The field side connection module provides 24 V power for the inputs of the 16-channel input module 750-1405/040-000, for example.This eliminates the need for additional terminal blocks.The 24 V supply and 0 V potential are derived from the internal power jumper contacts of an adjacent upstream I/O module. A connection of the potentials to the downstream I/O modules is made automatically via the power jumper contacts when snapping the I/O modules together. The 24 V power is provided to all 16 field-side CAGE CLAMP® S connections and the 0 V potential passed through without being used by the module.An operating tool with a 2.5 mm blade (210-719) is required to open the CAGE CLAMP® S connections.
The module is ideally suited for operation in harsh environmental conditions:- strongly extended temperature range - higher dielectric strength and EMC resistance- higher vibration and shock resistance
Description Item No. Pack. Unit
Field-Side Connection Module 16+ /XTR 750-1605/040-000 1
Accessories Item No. Pack. Unit
Miniature WSB Quick marking systemplain 248-501 5with marking see Section 11
Operating tool, with partially insulated shaft, type 1, blade (2.5 x 0.4) mm
210-719 50
ApprovalsConformity marking 1
Marine applications GLr UL 508 r ANSI/ISA 12.12.01 Class I, Div. 2, Grp. ABCD, T4
Technical DataWire connection CAGE CLAMP® SCross sections 0.25 mm² ... 1.5 mm² / AWG 24 ... 16Strip lengths 8 ... 9 mm / 0.33 inDimensions (mm) W x H x L 12 x 62 x 100
Height from upper-edge of DIN 35 railWeight 40.2 gOperating temperature -40 °C ... +70 °CStorage temperature -40 °C ... +85 °CRelative humidity 95 %, short-term condensation acc. to class 3K7
/ IEC EN 60721-3-3 (except wind-driven precipitation, water and ice formation)
Operating altitude without temperature derating: 0 m ... 2000 m; with temperature derating: 2000 m ... 5000 m (0.5 K/100 m); max.: 5000 m
Technical DataVoltage via power jumper contacts 24 VDC
under laboratory conditions +15 °C ... +35 °C 18 V ... 31.2 V (17.4 V ... 31.2 V)1)
for -40 °C ... +55 °C 18 V ... 28.8 V (17.4 V ... 28.8 V)1)
for +55 °C ... +70 °C 18 V ... 26.4 V (17.4 V ... 26.4 V)1)
1) including residual ripple of 15 %Current via power jumper contacts (max.) 10 AIsolation (peak value) 510 VAC or 775 VDC
power supply/DIN railRated surge voltage 1 kVOvervoltage category IIIVibration resistance acc. to IEC 60068-2-6 (acceleration: 5g),
EN 60870-2-2, IEC 60721-3-1, -3, EN 61131-2
Shock resistance acc. to IEC 60068-2-27EMC immunity of interference acc. to EN 61000-6-1, -2, EN 61131-2,
marine applications, EN 50121-3-2, -4, -5, EN 60255-26, EN 60870-2-1, EN 61850-3, IEC 61000-6-5, IEEE 1613, VDEW: 1994
EMC emission of interference acc. to EN 61000-6-3, -4, EN 61131-2, EN 60255-26, marine applications, EN 60870-2-1, EN 61850-3, EN 50121-3-2, -4, -5
750-1606/040-000
5426
Field-Side Connection Module 16-for eXTReme environmental conditions; 0 VDC
1 9
2 10
3 11
4 12
5 13
6 14
7 15
8 16
750-1606/040-000
13 14
0 V
0 V
0 V
0 V
0 V
0 V
0 V
0 V
0 V
0 V
0 V
0 V
0 V
0 V
0 V
0 V
CAGE CLAMP®Sconnection
Data contacts
Power jumper contacts
1
2
3
4
5
6
7
8
13
12
11
10
9
14
15
16
‒
‒
‒
‒
‒
‒
‒
‒
0 V
+ 24 V
‒
‒
‒
‒
‒
‒
‒
‒
750-1606/040-000
The field side connection module provides 0 V power.This eliminates the need for additional terminal blocks.The 24 V supply and 0 V potential are derived from the internal power jumper contacts of an adjacent upstream I/O module. A connection of the potentials to the downstream I/O modules is made automatically via the power jumper contacts when snapping the I/O modules together. The 0 V power is provided to all 16 field-side CAGE CLAMP®S connections and the 24 V potential passed through without being used by the module.An operating tool with a 2.5 mm blade (210-719) is required to open the CAGE CLAMP® S connections.
The module is ideally suited for operation in harsh environmental conditions:- strongly extended temperature range - higher dielectric strength and EMC resistance- higher vibration and shock resistance
Description Item No. Pack. Unit
Field-Side Connection Module 16- /XTR 750-1606/040-000 1
Accessories Item No. Pack. Unit
Miniature WSB Quick marking systemplain 248-501 5with marking see Section 11
Operating tool, with partially insulated shaft, type 1, blade (2.5 x 0.4) mm
210-719 50
ApprovalsConformity marking 1
Marine applications GLr UL 508 r ANSI/ISA 12.12.01 Class I, Div. 2, Grp. ABCD, T4
Technical DataWire connection CAGE CLAMP® SCross sections 0.25 mm² ... 1.5 mm² / AWG 24 ... 16Strip lengths 8 ... 9 mm / 0.33 inDimensions (mm) W x H x L 12 x 62 x 100
Height from upper-edge of DIN 35 railWeight 42.1 gOperating temperature -40 °C ... +70 °CStorage temperature -40 °C ... +85 °CRelative humidity 95 %, short-term condensation acc. to class 3K7
/ IEC EN 60721-3-3 (except wind-driven precipitation, water and ice formation)
Operating altitude without temperature derating: 0 m ... 2000 m; with temperature derating: 2000 m ... 5000 m (0.5 K/100 m); max.: 5000 m
Technical DataVoltage via power jumper contacts 24 VDC
under laboratory conditions +15 °C ... +35 °C 18 V ... 31.2 V (17.4 V ... 31.2 V)1)
for -40 °C ... +55 °C 18 V ... 28.8 V (17.4 V ... 28.8 V)1)
for +55 °C ... +70 °C 18 V ... 26.4 V (17.4 V ... 26.4 V)1)
1) including residual ripple of 15 %Current via power jumper contacts (max.) 10 AIsolation (peak value) 510 VAC or 775 VDC
power supply/DIN railRated surge voltage 1 kVOvervoltage category IIIVibration resistance acc. to IEC 60068-2-6 (acceleration: 5g),
EN 60870-2-2, IEC 60721-3-1, -3, EN 61131-2
Shock resistance acc. to IEC 60068-2-27EMC immunity of interference acc. to EN 61000-6-1, -2, EN 61131-2,
marine applications, EN 50121-3-2, -4, -5, EN 60255-26, EN 60870-2-1, EN 61850-3, IEC 61000-6-5, IEEE 1613, VDEW: 1994
EMC emission of interference acc. to EN 61000-6-3, -4, EN 61131-2, EN 60255-26, marine applications, EN 60870-2-1, EN 61850-3, EN 50121-3-2, -4, -5
750-600/040-000
5427
5
End Modulefor eXTReme environmental conditions
750-600/040-000
ABCD
EFGH
An end module must be snapped onto the assembly at the end of a fieldbus node.
The end module completes the internal data bus, while providing correct data transmission.
The module is ideally suited for operation in harsh environmental conditions:- strongly extended temperature range - higher dielectric strength and EMC resistance- higher vibration and shock resistance
Description Item No. Pack. Unit
End Module /XTR 750-600/040-000 1
Accessories Item No. Pack. Unit
Miniature WSB Quick marking systemplain 248-501 5with marking see Section 11
ApprovalsConformity marking 1
Korea CertificationMarine applications GLr UL 508 r ANSI/ISA 12.12.01 Class I, Div. 2, Grp. ABCD, T4
Technical DataDimensions (mm) W x H x L 12 x 62 x 100
Height from upper-edge of DIN 35 railWeight 32.5 gOperating temperature -40 °C ... +70 °CStorage temperature -40 °C ... +85 °CRelative humidity 95 %, short-term condensation acc. to class
3K7 / IEC EN 60721-3-3 (except wind-driven precipitation, water and ice formation)
Operating altitude without temperature derating: 0 m ... 2000 m; with temperature derating: 2000 m ... 5000 m (0.5 K/100 m); max.: 5000 m
Vibration resistance acc. to IEC 60068-2-6 (acceleration: 5g), EN 60870-2-2, IEC 60721-3-1, -3, EN 61131-2
Shock resistance acc. to IEC 60068-2-27EMC immunity of interference acc. to EN 61000-6-1, -2, EN 61131-2,
marine applications, EN 50121-3-2, -4, -5, EN 60255-26, EN 60870-2-1, EN 61850-3, IEC 61000-6-5, IEEE 1613, VDEW: 1994
EMC emission of interference acc. to EN 61000-6-3, -4, EN 61131-2, EN 60255-26, marine applications, EN 60870-2-1, EN 61850-3, EN 50121-3-2, -4, -5