Inventory Management Software - Emerson · Rosemount TankMaster WinSetup Inventory Management Software Cover Photo: ... Foundation: ). Customized views

Reference Manual303027EN, Edition 4January 2008

Rosemount TankMaster WinSetupInventory Management Software

www.rosemount-tg.com

Reference Manual 303027EN, Edition 4January 2008 Rosemount TankMaster WinSetup

Rosemount TankMaster WinSetup
Inventory Management Software
Cover Photo: WinStp_Ed4_303027EN_cover.tif

NOTICE

Read this manual before working with the product. For personal and system safety, and for optimum product performance, make sure you thoroughly understand the contents before installing, using, or maintaining this product.

For equipment service or support needs, contact your local Emerson Process Management/Rosemount Tank Gauging representative.

VersionThis manual describes the functionality of TankMaster WinSetup version 4.H1.For older TankMaster versions all functionality described in this manual may not be available and the Graphical User Interface (GUI) may look slightly different.

TrademarksHART is a registered trademark of HART Communication Foundation.

Modbus is a registered trademark of Modicon.

Pentium is a registered trademark of Intel Corporation.

Windows XP is a registered trademark of Microsoft Corporation.



Table of Contents
SECTION 1Getting Started
1.1 What is TankMaster?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11.2 TankMaster Software Package . . . . . . . . . . . . . . . . . . . . . . . . . 1-21.3 Installing the TankMaster Software . . . . . . . . . . . . . . . . . . . . . . 1-4

1.3.1 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . 1-41.3.2 Installed Software Modules . . . . . . . . . . . . . . . . . . . . 1-41.3.3 Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . 1-5

1.4 Installing a Tank Level Gauging System . . . . . . . . . . . . . . . . . . 1-61.5 Illegal characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

SECTION 2The WinSetup Main Window

2.1 Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-32.2 Toolbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-42.3 Status bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-52.4 Workspace - Viewing Tanks and Devices . . . . . . . . . . . . . . . . . 2-6

2.4.1 Workspace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-72.4.2 Icons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

2.5 User Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-102.5.1 Logging On to TankMaster. . . . . . . . . . . . . . . . . . . . 2-102.5.2 To Administrate User Accounts . . . . . . . . . . . . . . . . 2-112.5.3 To Set Required Access Levels . . . . . . . . . . . . . . . . 2-132.5.4 To Change Protection Level of Separate Windows . 2-142.5.5 To Change Password. . . . . . . . . . . . . . . . . . . . . . . . 2-152.5.6 To Change Inactivity Timeout . . . . . . . . . . . . . . . . . 2-16

SECTION 3Installing a Level Gauging System

3.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23.2 Communication Protocol Setup . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

3.2.1 Master Protocol Channel Configuration . . . . . . . . . . . 3-53.2.2 Slave Protocol Channel Configuration . . . . . . . . . . . . 3-83.2.3 Log File Configuration . . . . . . . . . . . . . . . . . . . . . . . 3-123.2.4 Changing the Protocol Channel Configuration. . . . . 3-133.2.5 Protocol Server Configuration . . . . . . . . . . . . . . . . . 3-13

3.3 Preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-143.3.1 Measurement Units . . . . . . . . . . . . . . . . . . . . . . . . . 3-143.3.2 Ambient Air Temperature . . . . . . . . . . . . . . . . . . . . . 3-153.3.3 Inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-163.3.4 Miscellaneous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-173.3.5 Setting the Name Tag Prefixes . . . . . . . . . . . . . . . . 3-183.3.6 Tank View Layout. . . . . . . . . . . . . . . . . . . . . . . . . . . 3-193.3.7 Tank Visibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22

3.4 Installing a Field Communication Unit (FCU) . . . . . . . . . . . . . 3-233.4.1 Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . 3-233.4.2 Summary of FCU Installation and Configuration . . . 3-29


Reference Manual303027EN, Edition 4

January 2008Rosemount TankMaster WinSetup

3.5 Tank Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-303.5.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-303.5.2 Starting the Tank Installation Wizard . . . . . . . . . . . . 3-313.5.3 Installing a New Tank. . . . . . . . . . . . . . . . . . . . . . . . 3-333.5.4 Summary of Tank Installation and Configuration . . . 3-413.5.5 To Change Tank Configuration . . . . . . . . . . . . . . . . 3-423.5.6 To Uninstall a Tank . . . . . . . . . . . . . . . . . . . . . . . . . 3-43

3.6 Device Installation - Overview . . . . . . . . . . . . . . . . . . . . . . . . . 3-443.7 Starting the Device Installation Wizard . . . . . . . . . . . . . . . . . . 3-453.8 Installing a Rex 3900 Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . 3-47

3.8.1 Step 1: Start the device installation wizard . . . . . . . 3-473.8.2 Step 2: Select device type . . . . . . . . . . . . . . . . . . . . 3-473.8.3 Step 3: Communication setup . . . . . . . . . . . . . . . . . 3-483.8.4 Step 4: RTG Configuration. . . . . . . . . . . . . . . . . . . . 3-513.8.5 Step 5: Tank Distances . . . . . . . . . . . . . . . . . . . . . . 3-633.8.6 Step 6: RTG Geometry . . . . . . . . . . . . . . . . . . . . . . 3-653.8.7 Step 7: DAU Configuration. . . . . . . . . . . . . . . . . . . . 3-663.8.8 Step 8: Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-68

3.9 Installing a Pro Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-713.9.1 Step 1: Start the device installation wizard . . . . . . . 3-713.9.2 Step 2: Select device type . . . . . . . . . . . . . . . . . . . . 3-713.9.3 Step 3: Communication setup . . . . . . . . . . . . . . . . . 3-723.9.4 Step 4: RTG Configuration. . . . . . . . . . . . . . . . . . . . 3-753.9.5 Step 5: Tank Distances . . . . . . . . . . . . . . . . . . . . . . 3-803.9.6 Step 6: RTG Geometry . . . . . . . . . . . . . . . . . . . . . . 3-823.9.7 Step 7: Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-83

3.10 Installing a TRL PU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-843.11 Installing an IOT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-863.12 Installing an Enraf CIU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-91

3.12.1 Configuration of the Egpudev.ini file . . . . . . . . . . . . 3-943.12.2 Configuration of an Enraf Gauge . . . . . . . . . . . . . . . 3-96

3.13 Installing an Endress & Hauser MDP 2 . . . . . . . . . . . . . . . . . . 3-983.14 Installing an LPG/LNG Tank Gauge . . . . . . . . . . . . . . . . . . . 3-101

3.14.1 Preparations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1013.14.2 LPG Configuration . . . . . . . . . . . . . . . . . . . . . . . . . 3-102

3.15 Setting up a Hybrid Tank Measuring system. . . . . . . . . . . . . 3-1083.16 Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-120

3.16.1 Manual Adjustment . . . . . . . . . . . . . . . . . . . . . . . . 3-1203.16.2 Using the Calibrate Function . . . . . . . . . . . . . . . . . 3-121

SECTION 4Device Handling

4.1 To Change Device Configuration . . . . . . . . . . . . . . . . . . . . . . . 4-14.2 To Uninstall a Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

SECTION 5Protocol Handling

5.1 Channel Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15.2 Logging the Channel Communication . . . . . . . . . . . . . . . . . . . . 5-35.3 Saving the Communication Log to File . . . . . . . . . . . . . . . . . . . 5-55.4 Searching for Connected Devices . . . . . . . . . . . . . . . . . . . . . . . 5-8

SECTION 6Viewing Tank Data

6.1 Viewing Data from All Tanks . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-16.2 Viewing Data From a Single Tank . . . . . . . . . . . . . . . . . . . . . . . 6-26.3 Tank Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-36.4 Tank Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4

TOC-2 Table of Contents


SECTION 7Viewing Alarm Status

SECTION 8Service Functions

8.1 Manual Relay Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-28.2 HART Device Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-38.3 User Defined Temperature Conversion. . . . . . . . . . . . . . . . . . . 8-4

8.3.1 Using a Linearization Table . . . . . . . . . . . . . . . . . . . . 8-48.3.2 Using a Mathematical Formula . . . . . . . . . . . . . . . . . 8-5

8.4 Viewing Input and Holding Registers. . . . . . . . . . . . . . . . . . . . . 8-68.5 To Edit Holding Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-78.6 Saving and Loading Database Registers . . . . . . . . . . . . . . . . . 8-8

8.6.1 To Save Device Registers . . . . . . . . . . . . . . . . . . . . . 8-88.6.2 To Load a Device Database. . . . . . . . . . . . . . . . . . . 8-10

8.7 Uploading new Gauge Software . . . . . . . . . . . . . . . . . . . . . . . 8-118.8 System Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-128.9 Tank Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13

8.9.1 Graph Area. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-158.9.2 Legend/Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-168.9.3 File Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-198.9.4 Action Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-228.9.5 Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-23

8.10 View Diagnostic Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-258.11 Overview IOT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-278.12 Customizing the Tools Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 8-29

SECTION 9TankMaster Administrator

9.1 Log on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-29.1.1 Changing the Administrator Program password . . . . 9-3

9.2 Autostart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-49.3 Backup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5

9.3.1 Restore. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-79.4 File Version Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-119.5 Processes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-12

SECTION 10Menu Items

10.1 File. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-110.2 View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-110.3 Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-210.4 Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-510.5 Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-5

TOC-3Table of Contents



TOC-4 Table of Contents


Section 1 Getting Started

1.1 What is TankMaster? . . . . . . . . . . . . . . . . . . . . . . . . page 1-11.2 TankMaster Software Package . . . . . . . . . . . . . . . . page 1-21.3 Installing the TankMaster Software . . . . . . . . . . . . . page 1-41.4 Installing a Tank Level Gauging System . . . . . . . . page 1-61.5 Illegal characters . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1-6

1.1 WHAT IS TANKMASTER?

TankMaster is an Emerson Process Management/Rosemount Tank Gauging inventory management software package for installation and configuration of level gauging equipment. The TankMaster program package provides you with powerful and easy-to-use tools for installation and configuration of level gauging devices. Devices such as radar transmitter gauges, data acquisition units and field communication units can easily be installed.

TankMaster is designed to be used in the Microsoft® Windows XP environment providing easy access to measurement data from your Local Area Network.

The TankMaster system allows you to use various protocols such as TRL/2 Modbus, RS232 and RS485 for connection to Local Area Networks (LAN) and host computers. You can easily change settings of protocols, devices and tanks at any time.

The graphical interface gives you a clear overview of installed devices and tanks. For each tank you can easily see the associated transmitters and data acquisition units.

Measured data is presented in real-time and you can customize the view of tank data to suit your needs.

Key Features• Monitoring of measured data.• Clear overview of installed tanks and devices.• Simple installation by using “wizards”.• Open connectivity.• Object oriented user friendly Graphical User Interface.




1.2 TANKMASTER SOFTWARE PACKAGE

Rosemount TankMaster comprises the following software modules:• WinOpi• WinSetup• Tank Server• Master Protocol Servers• Slave Protocol Server• Batch Server• Administrator

WinOpi is the operator´s interface to the Rosemount Tank Gauging system. It communicates with the Tank Server and the different protocol servers to let the user monitor measured tank data. WinOpi also provides alarm handling, batch report, automatic report handling, historical data sampling as well as inventory calculations like volume, observed density and other parameters.

The WinSetup program is a graphical user interface for installation, configuration and service of level gauging devices.

The Tank Server communicates with devices via the Master protocol server and handles configuration data for all the installed tanks and devices. Tank and device names, configuration data like antenna type, number of connected temperature sensors and analog inputs and many other parameters are stored by the Tank Server. The Tank Server collects measured data from connected devices and provides these data to the WinOpi/WinSetup user interface.

WINSETUP

Tank Server

Master Protocol Server Slave Protocol Server

COM1 COM2

Batch Server

WINOPI

1-2 Section 1. Getting Started


The Master Protocol Server transfers configuration data and measured data between the Tank Server and connected devices in a Rosemount Tank Gauging system. The Master Protocol Server is able to communicate with various types of devices such as Radar Tank Gauges (RTGs), Field Communication Units (FCUs) and Data Acquisition Units (DAUs) to collect measured data like for example level, temperature and pressure.

The Slave Protocol Server is used to connect the TankMaster system to a host computer (DCS system). The Slave Protocol Server exchanges tank data between the Tank Server and the host computer.

The Batch Server provides functions for starting, monitoring and closing batch transfers betweeen tanks. It also generates various reports during and after a batch transfer.

The Administrator program allows you to start and stop TankMaster, and to specify which TankMaster software modules that will start automatically when the PC is started. It also includes a backup and restore function, and functions for handling redundant Tank Servers and Batch Servers.

OPC Server with Browser

TankMaster uses OPC Data Access 2.0 (OLE for Process Control), an open industry standard, which eliminates the need for costly customized software integration. With the OPC server and the browser it is easy to import all custody transfer and inventory data to other OPC clients such as different DCS:s, PLC:s, Scada systems, or Microsoft Office® programs. This way, operators and plant management are better armed to make timely decisions as they work with distributed inventory and tank gauging data. (Website OPC Foundation: www.opcfoundation.org).

Customized views

In TankMaster you can change general and specific tank view and setup windows. You have a number of options to design your TankMaster as you like; you can either modify the existing windows or build completely new ones. For example you can have a photo of your own plant giving a quick realistic view and just by clicking a specific tank you will get corresponding tank data.

1-3Section 1. Getting Started



1.3 INSTALLING THE TANKMASTER SOFTWARE

1.3.1 System Requirements

The following is recommended to run TankMaster version 4.G0 or higher(1):• Operating system: Windows XP Professional Edition (SP 2).• Hardware TankMaster network PC

• Hardware TankMaster standalone or client PC

• Hardware TankMaster network, standalone or client PC:

NOTEWinSetUp does not require a hardware key.

1.3.2 Installed Software Modules

The following software program modules are installed:• TankMaster WinSetup program• TankMaster WinOpi program• Tank Server• Modbus Master Protocol server• Various Master Protocol servers• Various Slave Protocol servers• Batch server

(1) For previous TankMaster versions other system requirements apply. Please contact Rose-mount Tank Radar AB for more information.

Processor: 2 GHz Intel Pentium double processor or compatible single processor.

Internal Memory (RAM): 2048 MB (up to 20 tanks: 1024 MB).

Processor: 1 GHz Intel Pentium double processor or compatible single processor.

Internal Memory (RAM): 1024 MB (up to 20 tanks: 512 MB).

Recommended brand: IBM PC (Windows XP approved).

Hard Disk: 40 GB (TankMaster needs approx. 500 MB).

Two RS-232 ports (USB can be used if no RS-232 exists).

One parallel port or USB port for TankMaster hardware key.

A 17 inch or larger monitor is recommended.

Graphical card: 1152*864, 65536 colors.

Hardware key: One key for each PC with a TankMaster server or client.

Field Bus Modem FBM2180 (FBM 2171) or RS232/485.



1.3.3 Installation Procedure

To install the TankMaster software package do the following:

1. Insert the TankMaster CD-ROM.

Response: the installation wizard is started.

NOTE!If the installation wizard does not start automatically when the CD-ROM is inserted, double-click the file Tmcd.exe or click the Windows Start button

, choose Run and select the Tmcd.exe file on the TankMaster installation CD in order to start the TankMaster installation

2. Click the TankMaster button to install the TankMaster software. Follow the instructions in the installation wizard.

3. Install the Acrobat Reader software if you want to be able to read the online documentation in pdf format. If the corresponding check box is unselected, Acrobat Reader is already installed on your computer.

4. Finish the installation.

Installation Options

There are a number of installation options available:

Demo TankMaster in demo mode with demo database.

Client Client installation only, i.e. no Batch Server, Tank Server or Master Protocol will be installed.Suitable for network clients connected to a common Tank Server or in systems with redundant servers.

Server and Client Suitable for standalone systems, and for network servers.

Redundant server Server and client installation with possibility to setup redundant Tank Servers. Note that the redundant Batch Server function has to be manually configured after installation.

1-5Section 1. Getting Started



1.4 INSTALLING A TANK LEVEL GAUGING SYSTEM

Setting up a Tank Level Gauging system is based on two main activities:• Tank installation.• Device installation.

Tank installation

Tank installation includes specifying tank type, specifying which transmitter to associate to the tank and which source signals to use as input for various tank parameters.

Device installation

Device installation includes tasks such as configuration of field bus communication, specifying tank height and other geometrical parameters, specifying type of antenna to be used, configuration of temperature sensors, relays, pressure sensors and other external devices.

Wizards

In order to facilitate the installation process, TankMaster WinSetup guides you through the installation procedure by using so called “wizards”. WinSetup automatically walks through a step-by-step procedure which lets you focus on the important issues rather than trying to remember what to do next. The Online Help provides information for each step in case you need further assistance.

1.5 ILLEGAL CHARACTERS

Naming objects in TankMaster using certain characters may cause TankMaster to malfunction. The following characters should be avoided:

\ Reverse solidus % Percent sign

/ Solidus < Less-than sign

? Question mark > Greater-than sign

* Asterisk { Left curly bracket

[ Left square bracket } Right curly bracket

] Right square bracket ' Apostrophe

| Vertical line " Quotation mark



Section 2 The WinSetup Main Window

2.1 Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-32.2 Toolbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-42.3 Status bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-52.4 Workspace - Viewing Tanks and Devices . . . . . . . . page 2-62.5 User Management . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-10

The TankMaster main window includes the Workspace to display tanks and devices, a menu bar at the top of the screen, a status bar at the bottom of the screen and a number of buttons in the toolbar.

MinimizeMaximize

Close

Menubar

Toolbar

Workspace

Status bar




The Workspace window can be moved anywhere on the Main window. It can be docked to either side of the Main window, or it can be left floating.

Right click in the Workspace window and choose Allow Docking to place the Workspace window along the Main window side.

2-2 Section 2. The WinSetup Main Window


2.1 MENUS The menu bar at the top of the screen contains menus such as File, View, Service, Tools, and Help.

Service menu options are also available by clicking the right mouse button. Different options are available depending on the type of object selected in the Workspace window. For example, by selecting the Devices folder and clicking the right mouse button the following menu appears:

Selecting an RTG and clicking the right mouse button brings up a menu with different configuration and service options:

2-3Section 2. The WinSetup Main Window



2.2 TOOLBAR The toolbar provides buttons acting as shortcuts to certain menu options. Normally the Toolbar is visible. To hide it, open the View menu and deselect the Toolbar option:

The following items are included in the standard toolbar:

1. Lets you log off to View Only mode.2. Lets you log on to TankMaster as Operator, Supervisor or Administrator.3. Lets you rename a tank.4. Lets you search for a tank or a device in the workspace tree structure.5. Opens the Properties dialog.6. Opens the Tank View window.7. Lets you install a new tank.8. Lets you install a new device.9. Lets you uninstall a tank.

10. Lets you uninstall a device.11. Lets you turn the Workspace window On or Off.12. About WinSetup

Toolbar option

1 2 3 4 5 6 7 8 9 10 11 12



2.3 STATUS BAR The status bar is located at the bottom of the TankMaster main window. It provides general information about the current system state.

Normally, the TankMaster status bar is visible. To hide it, open the View menu and deselect the Status bar option.

The status bar displays information about a device, tank or any other item that is selected in the WinSetup main window. The connection status, current user, current protection level (View Only, Operator etc.) and operation status are also shown.

Status barStatus bar

Connection status

Current user

Current protection level

Indicator normal operation




2.4 WORKSPACE - VIEWING TANKS AND DEVICES

The workspace displays an overview of all devices and tanks. You can switch between two different views: Logical and Physical view.

In the workspace you can perform varioius tasks such as:• Install and configure tanks, devices, and protocols• Remove tanks and devices• Change the configuration of tanks and devices• View database and input registers• Setup the tank view layout• Specify tags for tank and device names• Upload new application software to a radar tank gauge• View communication log

Choose this tab to show the Logical View.

Choose this tab to show the Physical View.



2.4.1 Workspace The Workspace window shows the installed tanks and devices and available communication protocols. It also provides information about the configuration of installed devices.

Ex.1 In the Logical View all installed tanks and devices, as well as available communication protocols, are organized in separate folders to provide a clear overview of the system.

Ex.2 The Tanks folder contains an overview of the installed tanks. For each tank the associated devices are displayed.

Ex.3 The Workspace provides information that reflects the system configuration. In this example the symbols indicate that transmitter LT-3 communicates with This Workstation via Field Communication Unit FCU-1. Transmitter LT-1 communicates directly with This Workstation.




Ex.4 A “+”-sign indicates that a transmitter is installed with an associated DAU. If there is no “+”-sign, there is no device associated with the RTG.

Ex.5 The available communication protocols are displayed in the Protocols folder.



2.4.2 Icons In the Workspace window the different tanks and devices are represented by the following icons:

Cylindrical tank, HTG fixed roof

Floating roof tank, HTG floating blanket

Spherical tank

Horizontal tank

HTG floating roof tank

Rex Radar Tank Gauge (RTG)

Field Communication Unit (FCU)

Slave Data Acquisition Unit (SDAU)

TRL PU

IOT 5110

IOT 5120

IOT 5130

IOT 5140

MCG32XX

MDPII

CIU

DS4

COM port status




2.5 USER MANAGEMENT

TankMaster provides several protection levels allowing you to prevent unauthorized changes. These protection levels are categorized as User Access Levels and User Sub Access Levels. The User Access Levels are Administrator, Supervisor, Operator, and View Only where each have five User Sub Access Levels providing a total of 20 unique access levels.

In order to change tank and device configuration, to install new tanks and devices, to calibrate a transmitter, to change holding register values etc. you have to be logged on to TankMaster. To perform any such action you have to be logged on at the required access level for that action, see “To Set Required Access Levels” on page 2-13.

You can be logged on in Administrator, Supervisor, Operator, or View Only mode. The default usernames and passwords for the four User Access Levels are:

2.5.1 Logging On to TankMaster

1. From the File menu choose Log On or click the Log On button in the WinSetup toolbar.

2. Type your Username and Password. The password is case sensitive but the username is not.

NOTE!If logging on fails five consecutive times the user account is disabled. In this case the user account has to be enabled by an administrator.

3. Click the OK button.The currently logged on user and the corresponding protection level is displayed in the WinSetup status bar.

View Only Default username: ViewDefault password: view

Operator Default username: OperatorDefault password: oper

Supervisor Default username: SupervisorDefault password: super

Administrator Default username: AdministratorDefault password: admin

Username User Access Level



2.5.2 To Administrate User Accounts

TankMaster allows you to setup a number of users at different levels and sub levels. You must be logged on as an Administrator in order to add new user accounts or to change the existing user account settings.

To add a new user:

1. Log on as an Administrator.2. From the Tools>Administrative Tools menu choose User Manager.

3. In the User Manager window select a cell in an empty row and click the New button.

4. Type a user name and a password. If you like, enter a description in the Description field.

5. Choose the desired User Access Level and Sub Level and click the OK button. See “User Management” on page 2-10 for further information on the available User Access Levels and Sub Levels.




6. Check that the new user appears in the User Manager window.Select the “Use first account...” box if you want a default user name to appear in the Log On dialog whenever it is opened. If this box is unmarked the User Name field is empty when the Log On dialog opens.

7. To configure the access sub level descriptions, click the Config Desc button and enter new descriptions in the various fields.

8. Click the OK button.

A new user account is added

Use first account with required access level as default



2.5.3 To Set Required Access Levels

In TankMaster WinSetup, you can set the access level required for the following actions:

• Tank/Device Install and Uninstall• Tank/Device Configuration• Replace, Restore and Restart Device• Protocol Configuration• Exit WinSetup• Add Program (see “Customizing the Tools Menu” on page 8-29)• Start Program (in the Tools menu)

For example, if you are logged on as an Operator (* * * * *), you are not allowed to exit WinSetup if the required exit level for this action is set to Supervisor (*) or higher.

To set the required access levels:

1. From the Tools/Administrative Tools menu choose Set Required Access Levels.

NOTE!You have to be logged on as an Administrator (* * * * *) to be able to set the required access levels. To create an Administrator (* * * * *) account, see “To Administrate User Accounts” on page 2-11.

2. Set the required access levels for each type of action and click the OK button.




2.5.4 To Change Protection Level of Separate Windows

In TankMaster it is possible to set a Protection Level for a specific window, e.g. the Properties window for a Rex gauge. This function is only available if you are logged on at the Administrator (* * * * *) level. To change the protection level do the following:

1. Put the cursor on the icon at the upper left corner and click the left mouse button.

2. Choose the Protection Level option.

NOTE!You have to be logged on as an Administrator (* * * * *) to be able to change the Protection Level. To create an Administrator (* * * * *) account, see “To Administrate User Accounts” on page 2-11.

3. Select the desired protection level from the drop down menus and click the OK button. Now changes in this window can only be performed if you are logged on at the specified Protection Level or higher.

2. Select Protection Level.1. Click icon.



2.5.5 To Change Password

TankMaster allows you to change your password at any time:

1. From the Tools/Administrative Tools menu choose the Set Password option.

2. Select the TankServer on which your user account is valid. You can see the different servers in the WinSetup workspace window. (If you are logged on, the current server is already selected in the Change User Password window).

3. Enter your username if the workspace is in View Only mode. If you are already logged on, your username appears in the Username field.

4. Enter the old password and the new password in the corresponding fields.

NOTE!The password is case sensitive.

5. Confirm the new password and click the OK button.




2.5.6 To Change Inactivity Timeout

TankMaster WinSetup includes the option to set a timeout after which the current user is automatically logged off. The timeout period is reset each time the user performs an activity that requires an access level check, for example changing the configuration of a device or logging on to WinSetup.

To set the Inactivity Timeout:

1. From the Tools/Administrative Tools menu choose the Set Inactivity Timeout option (you have to be logged on as Administrator).

2. Type the desired value in the corresponding input field.3. Click the OK button.



Section 3 Installing a Level Gauging
System
3.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3-23.2 Communication Protocol Setup . . . . . . . . . . . . . . . page 3-43.3 Preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3-143.4 Installing a Field Communication Unit (FCU) . . . . . page 3-233.5 Tank Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3-303.6 Device Installation - Overview . . . . . . . . . . . . . . . . . page 3-443.7 Starting the Device Installation Wizard . . . . . . . . . page 3-453.8 Installing a Rex 3900 Gauge . . . . . . . . . . . . . . . . . . page 3-473.9 Installing a Pro Gauge . . . . . . . . . . . . . . . . . . . . . . . page 3-713.10 Installing a TRL PU . . . . . . . . . . . . . . . . . . . . . . . . . . page 3-843.11 Installing an IOT . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3-863.12 Installing an Enraf CIU . . . . . . . . . . . . . . . . . . . . . . . page 3-913.13 Installing an Endress & Hauser MDP 2 . . . . . . . . . . page 3-983.14 Installing an LPG/LNG Tank Gauge . . . . . . . . . . . . page 3-1013.15 Setting up a Hybrid Tank Measuring system . . . . . page 3-1083.16 Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3-120




3.1 OVERVIEW Before starting to install a Rosemount Tank Gauging system you should make sure that the following information is available:

• A plan of all the devices and tanks. Note the Unit Id of each device and all the communication addresses to be used (the Unit Id is a unique identity given to each RTG, FCU and DAU at manufacturing).

• All relevant reference distances like tank height, distance between Zero level and tank bottom etc.

To install a level gauging system you should follow the procedure described below:

1 Communication Protocol Setup.

Specify communication protocol parameters:

• The Master Protocol handles the communication between the TankMaster PC and field devices such as the Field Communication Unit (FCU).

• The Slave Protocol is used for communication with a host computer.• If you want to supervise the communication on the bus you can specify

the type of errors, function codes etc. to be logged.

2 Preferences.

Specify measurement units, tag prefixes for tank and device labels and parameters to be displayed when viewing tank data.

3 Install and Configure the Field Communication Unit (FCU).

If the system contains a FCU it has to be installed and configured before other devices like RTGs and DAUs. To install a FCU you need to:

• Assign an address. • For each communication port, choose protocol and set the appropriate

communication parameters. • Configure the slave database which holds information about the

devices connected to the field bus.

4 Tank and Device installation and configuration.

You can choose one of two methods when installing tanks and devices:

Alternative 1: Start by installing the tanks. In this case devices are installed as part of the tank installation procedure.

Alternative 2: Start by installing and configuring the devices. When the devices are installed, continue with installing the tanks and associate the tanks to the appropriate devices.

3-2 Section 3. Installing a Level Gauging System


Tank Installation

Installing a tank includes the following steps:

Device Installation

Installing a device includes the following steps:

5 Calibration.

When a Rex 3900 transmitter is installed and configured you need to adjust the Calibration Distance in order to match measured level and actual product level. The adjustment should be performed once at the final commissioning. A calibration may need to be repeated if tank conditions are changed.

Choose tank type Select one of the available options such as Fixed Roof, Floating Roof, Sphere LPG, Horizontal LPG etc.

Specify a tank tag Specify a name to be used as an identifier in the Workspace window and other windows.

Select devices Associate devices to the tank.Configuration Specify the available source signals for parameters

such as Free Water Level, Vapor Pressure and Liquid Pressure.

Value Entry If you want to disconnect automatic measurement of a certain parameter, you can specify a manual value to be used instead. You can also specify a value range to each measured variable.

Communication Specify protocol and address.Configuration Specify tank distances, geometrical distances

related to the transmitter, external sensors like temperature sensors and other parameters depending on what type of device that is installed.

3-3Section 3. Installing a Level Gauging System



3.2 COMMUNICATION PROTOCOL SETUP

The TRL/2 Modbus Master protocol is available as default protocol when Rosemount TankMaster is installed on your computer. Other protocols, like the TRL/2 Modbus Slave protocol, can be obtained as options. Contact Emerson Process Management / Rosemount Tank Gauging for more information.A protocol offers up to eight channels. For each channel you can specify which PC communication port (COM) to connect to, and standard communication parameters such as Baud Rate and Stop Bits.

For each protocol you can configure the following:• Communication parameters: COM Port, Baud rate, stopbits, modem

type, etc.• Log file: File name, file size, log schedule.• Tank mapping (For slave protocols only)

To Host computer (COM2)

TRL/2 Modbus (USB/COM1)

(Master Protocol)

(Slave Protocol)

FIELD BUS MODEM

Field Communication Unit

The OPI work station can be connected to field devices and a host computer by using Master and Slave protocols.

COMPUTERMaster Protocol Server

Channel 1Channel 2Channel 3Channel 4Channel 5Channel 6Channel 7Channel 8

Slave Protocol Server

COM 1

COM 2Channel 1Channel 2Channel 3Channel 4Channel 5Channel 6Channel 7Channel 8



3.2.1 Master Protocol Channel Configuration

To configure a protocol do the following:

1. Open the Protocols folder in the Workspace window.2. Select the icon that corresponds to the particular protocol to be

configured (ModbusMaster, ModbusSlave etc.).

3. Click the right mouse button and select Properties or choose Protocols/Properties from the Service menu.

4. The Protocol Properties window shows an overview of enabled and disabled protocol channels.

5. Select the desired channel.6. Click the Properties button to configure the protocol channel.

1. Select the Modbus Master protocol

2. Click Properties




7. Select the Communication tab.

The Communication tab lets you configure parameters which control the communication between the TankMaster work station and the Field Communication Unit (FCU).The Log File tab lets you specify the type of information to be logged and saved to disk (see also “Log File Configuration” on page 3-12).

8. Set the communication parameters:

NOTE!If the communication is broken and handshaking includes DSR, no query will be sent from the TankMaster Protocol Server. This may result in a Query Timeout.

9. The Comm. disabled in backup mode check box can be used for systems with redundant tank servers. If the check box is selected, the ModbusMaster will not send any queries if the local tank server is in backup mode.

10. Select the Enable Channel check box to activate the protocol channel and click the OK button.

Port The COM port that the FBM will be connected to

Baud rate 4800

Stop bits 1

Parity None

Modem Choose FBM if you use a Field Bus Modem.

Handshaking FBM: RTS/CTS/DTR/DSRRS485: RTS/CTSRS232: None

Reply timeout 1000 ms

Retries 10

Description Text describing the configured channel



11. Now the Modbus Master Channel 1 icon appears in the WinSetup workspace:

Modbus Master channel 1 is enabled




3.2.2 Slave Protocol Channel Configuration

A Slave protocol allows you to collect data from the TankMaster workstation to a host computer.

NOTE!A hardware key must be installed in order to run a slave protocol server.

TRL/2 Modbus Communication Setup

To configure the TRL/2 Modbus Slave protocol channel do the following:

1. Open the Protocols folder in the Workspace window.2. Select the ModbusSlave icon.

3. Choose Protocols/Properties from the Service menuor click the right mouse button and select Properties.

4. The Protocol Properties window shows an overview of enabled and disabled protocol channels.

5. Select the desired channel.6. Click the Properties button to configure the protocol channel.

1. Select the Modbus Slave protocol

2. Click Properties



7. Select the Communication tab.8. Select the Enable Channel check box and click the OK button to

activate the protocol channel.9. Set the following communication parameters:

NOTE!If handshaking includes DSR, no query will be sent from the TankMaster Protocol Server if the communication is broken. This may result in a Query Timeout.

Port Choose the COM port that the host computer will be connected to.

Baud rate 4800

Stop bits 1

Parity None

Modem Choose the appropriate interface. Select FBM if you are using a TRL/2 Field Bus Modem.

Handshaking FBM: RTS/CTS/DTR/DSRRS485: RTS/CTSRS232: See the specifications for the communication software used on the host computer

Address Set the address to be used by the host computer to identify the TankMaster workstation.

Description Text describing the configured channel.




Advanced Configuration

To configure delay times and time-outs do the following:

1. Click the Advanced button in the Communication tab.

2. Use the following default values for the TRL/2 Modbus Slave protocol:

The Async Mode can be used to improve the communication when the system is communicating on many Com ports.

The Backup Mode has three options:• None• Write Commands Rejected• Silent

In Silent mode the ModbusSlave protocol will not send any replies to requests coming from the host computer while the local tankserver is in backup mode.

Query to Response Delay 10 msQuery interval 100 msRead Query Timeout 400 msWrite Response Timeout 400 msMax. Response Time 800 msBackup Mode None



Tank mapping configuration

The slave protocol allows you to send data from a Rosemount Tank Gauging system to a host computer. To specify which tanks to collect data from do the following:

1. Select the Tank Mapping tab.

2. From the list in the Available Tanks pane select the tanks that you want to connect to.

3. Click the button to move the selected tanks into the Mapped Tanks list.

Make sure that the tanks appear in the order required by the host system. When the host sends a query, TankMaster responds with sending tank data in the same order as the tanks are listed in the Mapped Tanks column.

You can easily change the order between tanks by using the and buttons.

4. Click the OK button to save the current configuration.




3.2.3 Log File Configuration

To save the communication log to disk do the following:

1. Select the File Log tab.

2. Type a name of the log file. (The log file is stored in the .../Rosemount/Server/Log directory).

3. Specify the maximum file size to be used. This option can be useful if you for example want to copy the log files to diskette.

4. In the Log Schedule box select Automatic and specify Date and Time if you want the logging to start automatically.You can also start the logging manually by pressing the Start button.

5. Specify if you want to create one or several log files. Choose the Several Files option if you for example want to optimize file size for storing on diskette. By choosing this option the logging continues by creating new files when the size of the current log file reaches the Maximum File Size. The maximum number of files that will be created is given by the Max Log Files parameter.

NOTE!If the maximum number of files is reached, TankMaster starts to replace the contents of the existing log files.

6. Click the Advanced button if you want to log specific function codes, addresses or error types.



3.2.4 Changing the Protocol Channel Configuration

A channel configuration can be changed at any time. To change the current configuration do the following:

1. In the WinSetup Workspace open the Protocols folder and the protocol subfolder with enabled channels.

2. Select the channel icon.3. Click the right mouse button and choose Properties

- or -from the Service menu choose Channels>Properties.

4. Choose the appropriate tab and make the desired settings according to the description in previous sections.

3.2.5 Protocol Server Configuration

You can specify which protocol servers that will be connected when TankMaster WinSetup starts. To change the current configuration do the following:

1. In the WinSetup workspace select the Protocols folder.2. Click the right mouse button and choose the Configure option:

3. In the Connect column, select the protocols that you want to be automatically connected when WinSetup starts up.




3.3 PREFERENCES

3.3.1 Measurement Units

Specify measuring units for inventory calculations. To change measurement units do the following:

1. Select the desired server (e.g. “This Workstation”) in the WinSetup workspace.

2. From the Service menu choose Servers/Setup and select the Units tab:

3. Select the Units tab. Choose desired units for level/ullage, temperature, pressure, volume, density, and weight.

4. Press OK.

NOTE!Make sure that the desired measuring units are specified before installing a new tank.

Note that these settings only affect installation of new tanks. Tanks which are already installed in the WinSetup Workspace will not be affected. This means that in order to change units for an existing tank you have to do the following:

1. Uninstall the tank.2. Change measurement units in the Server Preferences/Units window (or

in the WinOpi program choose menu option Setup>System and change units in the System Setup window).

3. Install the tank again.



3.3.2 Ambient Air Temperature

To change the Ambient Air Temperature preferences do the following:


2. From the Service menu choose Servers/Setup and select the Ambient Air Temperature tab:

3. Choose Auto when there is a temperature sensor available that can be used to measure the Ambient Air Temperature.If there is no temperature sensor available, select the Manual option and enter a manual value for the Ambient Air temperature.

• Device. Click the button and select the device to which a temperature sensor is connected.

• Source. Select the temperature source from either Temperature, AIn (Analog In), or HIn (HART In; see Rosemount TankRadar Rex Installation Manual ref.no 308014E for more info on analog inputs and HART inputs).

• Sensor. Choose the actual sensor to be used for Ambient Air Temperature.

• Value Range. The Value Range defines the minimum and maximum value when Ambient Air Temperature is manually entered.

4. Press OK.




3.3.3 Inventory To change the Inventory settings do the following:


2. From the Service menu choose Servers/Setup and select the Inventory tab:

3. Local Gravity.The Local Gravity is used for density and weight calculations when an optional pressure transducer is installed.Select Manual if you like to use a specific Local Gravity value.Choose Calculated if you want the local gravity to be calculated by TankMaster. In this case you need to enter the Latitude and Elevation at your site.

4. Ambient Air Density.The Ambient Air Density is used for calculating the Weight in Air (WIA).Select Manual if you like to use a specific Ambient Air Density value. Choose Calculated if you want the Ambient Air Density to be calculated by TankMaster. The calculated value is based on the Base Density and the Ambient Air Temperature. See the WinOpi User´s Guide (ref. no. 303028EN) for more information on inventory parameters.

5. Press OK.



3.3.4 Miscellaneous To change the Miscellaneous parameters do the following:


2. From the Service menu choose Servers/Setup and select the Miscellaneous tab:

3. Choose a Tank Capacity Table (TCT) type to be used as default setting when installing new tanks. This TCT type is automatically chosen when strapping tables are created for new tanks. The TCT type can however be changed in the Tank Capacity Setup window at the occassion when the strapping table is specified regardless of the settings in the Server Preferences window.

4. You can choose between Raw, International and Northern. See further information in TankMaster WinOpi Reference Manual.

5. Specify the maximum number of Digital Alarms.6. Specify reference temperature to be used for inventory calculations.

Normally, the standard value 15 °C is used.7. Press OK.




3.3.5 Setting the Name Tag Prefixes

TankMaster WinSetup allows you to specify default name tag prefixes to be used when installing tanks and devices. These prefixes can be ignored if you want to use another prefix instead.

To specify name tag prefixes do the following:

1. From the Service menu choose Preferences.

2. Select the Tag Prefixes tab.3. Type the prefixes to be used for tank names and device names and click

the OK button.You can change the prefixes later at any time. If you specify new name tag prefixes this will not affect existing tank and device names.



3.3.6 Tank View Layout The Setup Tank View tab is used to specify which variables to be included in the Tank View window, see also Section 6: Viewing Tank Data.

You can create a new tank view layout and store it on disk, or you can load an existing table layout.

To specify a layout do the following:

1. From the Service menu choose Preferences.2. In the Preferences window select the Setup Tank View tab.

3. Click the Load Table button if you like to edit an existing Table Layout.4. To design a new Table Layout:

in the left pane (Available Parameters) select the variable to be displayed in the Tank View window (see “Viewing Tank Data” on page 6-1).

5. Click the Move button to move selected parameter to the Selected Parameters pane on the right-hand side of the Setup Tank View window.

6. Repeat steps 4 to 5 for each variable you want to include. Click the Move All button if you want to move all variables to the right pane.

7. Check that Selected Parameters shows the desired parameters.




8. Click the Save As button if you like to save the current tank view table for future use.

9. Click the OK button to confirm the Tank View settings.

NOTE!When clicking the Apply or the OK button, the parameter setup is stored in the currently open table layout which is used by the Tank View window.



To view the specified tank parameters click the right mouse button and choose the Open Tank View option:




3.3.7 Tank Visibility The Tanks Visibility tab is used to configure which tanks that will be visible on the current WinOpi client.

To specify visible tanks:

1. From the Service menu choose Preferences and select the Tanks Visibility tab:

2. Select the checkbox labeled Enable Tank Visibility function.3. Select the tank server with the tanks that you want to configure. 4. Choose whether new tanks shall be visible or hidden on the current work

station.5. Click the OK button to store the current configuration.

Enable

Tank Server

New tanks: visible/hidden

Before After



3.4 INSTALLING A FIELD COMMUNICATION UNIT (FCU)

Installing a Field Communication Unit basically includes the following steps:

1. Specify device type and name tag.2. Enable communication with the TankMaster PC:

• Select communication channel.• Set the desired address.

3. Configure the FCU:• Set Port type (Field Bus/Group Bus), Baud rate, Data bits, Stop bits,

Parity.• Specify if there is a redundant FCU connected.

4. Configure the Slave Database:For devices connected to the FCU specify device type, address, Field Bus (FB1...) number, number of temperature sensors, number of analog inputs Ain, Interval 1, Interval 2.

3.4.1 Installation Procedure

Step 1. Start the device installation wizard.

Start the installation wizard as described in “Starting the Device Installation Wizard” on page 3-45.

Step 2. Select device type.

1. Choose device type FCU.2. Specify a name for the FCU in the Tag input field. Rosemount

TankMaster automatically suggests the first part of the name according to the settings in the Tag Prefixes window, see “Setting the Name Tag Prefixes” on page 3-18.

3. Click the Next button to continue.




Step 3. Communication setup.

Select a communication protocol channel. (To check the available channels, open the Protocols folder, select the Master Protocol icon, click the right mouse button and choose Properties, see “Communication Protocol Setup” on page 3-4.

NOTE!For more information on FCU Redundancy, see the Rosemount TankMaster Redundancy System - User´s Guide (reference number: 303032E).

To set a new address do the following:1. In the FCU Communication window click the Change Address on

Device button.

Response: the Change Address window is opened.

2. Enter the Unit ID and the desired address and click the OK button.

Response: the Change Address window is closed.

3. In the FCU Communication window click the Verify Communication button to make sure that communication is established.




Step 4. FCU configuration

1. Check that the correct port is selected. The FCU has six communication ports. Normally they are configured as two Group Bus ports and four Field Bus ports. You can connect Group Bus ports to TankMaster work stations as well as to host computers. The Field Bus ports are connected to RTGs and DAUs.

2. Check that the correct protocol is selected. Use the MODBUS communication protocol for Group Bus ports. For Field bus ports you can use the following protocols:

Set the following modem communication parameters for the MODBUS protocol:

3. For standard installations make sure that No Redundancy is selected. See the Rex Service Manual for information on how to configure systems with redundant FCUs.

4. Click the Next button to open the FCU Slave Database window.

MODBUS for TankRadar Rex and TRL/2 devices Labko2000 for ILS2000,WS400 for Echowave gauges.

Baud rate 4800Databits per character 8Stop bits 1Parity No




Step 5. Slave Database Setup

This window is used to enter all the information that a FCU needs in order to collect information from connected units.

Data from the RTGs, DAUs and external sensors is sent to the FCU and distributed to the TankMaster PC on the Group Bus.

Click at the row (1A, 2A ...) in the FCU Configuration window where you want to enter data for the slave to be configured.

To configure the FCU slave database

1. Enter the Slave type. There are 64 positions in the FCU Configuration window. The first 32 positions are dedicated to Rex, Pro, RTG 2900, ILS2000 and Echowave gauges. After position 32 the numbering restarts at 1. The second group of 32 positions is dedicated to DAUs only.

NOTE!Make sure that a level gauge and its associated DAU are entered at the same position (for example 1A and 1B) in the FCU Slave Database window.

2. Enter the address of the associated device. We recommend that address 1 to 99 is used for RTGs and 101 to 199 for DAUs.

3. Select the Field Bus that the slave device is connected to. Normally there are four field buses available, see the Rex Service Manual for more information.

4. Enter the number of temperature sensors. For a Rex gauge up to six temperature sensors can be connected to the transmitter head.

5. Enter the number of analog inputs to be used. A Rex gauge can use a maximum of two current inputs.

6. Enter the number of HART slaves in the REX Hin field.7. Enter the number of relay outputs in the REX Relays field.



8. Interval 1 (Int.1): enter the time interval between requests for level data and analog input data from a REX gauge, and temperature data from a DAU. Interval 1 is given in units of 1 second.For Rex it is recommended that Interval 1 is equal to 1 second, and for the DAU Interval 1 should be set to 10 seconds.

9. Interval 2 (Int.2): enter the time interval between requests for temperature, HART and relay data from a REX gauge. Interval 2 is given in units of 1 second. Recommended value is 10 seconds.

10. Level Offset is used for Echowave and ILS2000 transmitters only. 11. Click the Next button to open the Summary window. 12. Check that the displayed data is correct. Click the Finish button to exit

the FCU installation.If there is something that needs to be changed before finishing the FCU configuration, click the Back button until the desired window appears.

Summary of FCU Slave Database Entry fields

It is very important that the Slave Database is properly configured. The following example shows how the FCU Slave Database and the actual system are related.

Slave type RTG, Rex (pos 1-32) or DAU (pos 1-32)

Address The address used for the current unit. For RTGs it is recommended that address 1 to 99 is used. For DAUs address 101 to 199 is recommended.

FCU field bus Enter the number of the field bus used by the selected unit. In the standard configuration there are four field buses available.

Temps Number of temperature elements in the tank

Analog inputs Number of analog inputs of the RTG (or an IDAU).

REX Hin The number of HART slaves.

REX Relays The number of relay outputs.

Interval 1 The smallest time interval between requests for level and analog input. Also used for temperature data from a DAU. Unit: 1 second. Normally Com. interval 1 is set to 1 second for Rex data and 10 seconds for DAU data.

Interval 2 The smallest time interval between requests for temperature, HART and relay data from a REX gauge.Unit: 1 second. Recommended value is 10 seconds.




Tank 1RTG 1 and DAU 1 communicate with an FCU via Field Bus 1.

Two analog inputs are connected to the RTG 1.

Eight temperature sensors are connected to DAU 1.

Tank 2RTG 2 and DAU 2 communicate with an FCU via Field Bus 1.

No analog inputs are connected to RTG 2.RTG 2 has one relay output.

Eight temperature sensors are connected to DAU 2.

FIELD BUS 1

TANK 1 TANK 2

RTG 1:Address = 1Ain = 2

DAU1:Address = 101

RTG 2:Address = 2Ain = 0

DAU2:Address = 102

RTG 1RTG 2

FCU

RTG1RTG2

DAU1 DAU2

EXAMPLE: A FCU CONNECTED TO TWO TANKS.

DAU 1DAU 2



3.4.2 Summary of FCU Installation and Configuration Select device type FCU.

Communication setup.

Assign an address and choose communication channel.

FCU configuration.

Specify communication parameters for each port.

Slave database configuration.

Configure RTGs and DAUs connected to the FCU.




3.5 TANK INSTALLATION

3.5.1 Overview Basically the purpose of the tank installation procedure is to associate a level gauge to a certain tank. You are also given the opportunity to specify analog input signals to be used for certain measured quantities such as Vapor pressure.

By using the Tank Installation wizard, installing a new tank is a simple and straightforward procedure.

NOTE!Make sure that the desired measuring units are specified before installing a new tank.

The specified measuring units only affect installation of new tanks. Changing measurement units has no effect on tanks which are already installed in WinSetup. This means that if you want to change measurement units for a previously installed tank, it has to be uninstalled first, and then installed again after changing the measurement units in the System Setup. See also “Measurement Units” on page 3-14.

A tank installation includes the following steps:

1. Specify tank type: Fixed Roof, Floating Foof, Sphere, Horizontal etc.2. Select which devices to associate with the tank.3. Configure the tank:

Specify analog input signals for Free Water Level (FWL), Vapor Temperature, Vapor Pressure and Liquid Pressure to be used for inventory calculations.

4. Specify automatically measured or manual values as input for the different tank variables.

5. Summary: provides brief information about the installed tank.



3.5.2 Starting the Tank Installation Wizard

The tank installation wizard can be started in several ways:

In the workspace/logical view:

1. Select the Tanks folder.

2. Click the right mouse button and choose Install New from the popup menu

- or -

from the File menu choose Install New/Tank.

As an alternative you can use the following method:

1. Select the server where your system is installed.

2. From the File menu choose Install New/Tank.




In the workspace/physical view:

See also “Installing a New Tank” on page 3-33.

1. Select the server where your system will be installed.

2. From the File menu choose Install New/Tank.



3.5.3 Installing a New Tank

Step 1. Start the tank installation wizard.

See “Starting the Tank Installation Wizard” on page 3-31 on how to start the tank installation wizard.

Step 2. Choose the desired tank type.

Available options are: • Fixed Roof• Floating Roof• Sphere• Horizontal• LPG Sphere• LPG Horizontal• Servo Tank Fixed Roof• Servo Tank Floating Roof• Servo Tank Sphere LPG • Servo Tank Horizontal LPG• Servo Tank Sphere• Servo Tank Horizontal• HTG Fixed Roof• HTG Floating Roof• HTG Floating Blanket

Enter a name in the Tank Tag input field. A prefix appears automatically if you have defined one in the Tag Prefixes window, see “Setting the Name Tag Prefixes” on page 3-18.

Click the Next button.




Step 3. Select devices to associate with the current tank.

Do one of the following:• choose from the list in the Available Devices box if there are devices

already installed• click the Install New Device button to install devices to associate with

the tank (this will start the device installation wizard). See “Device Installation - Overview” on page 3-44 for further information on how to install different Radar Tank Gauges and Data Acquisition Units.

NOTE!If a device installation was started in the tank installation process, and interrupted before the installation was finished, the communication address in the actual device may have been changed anyway!

NOTE!Make sure that the Show FCU Slave Positions check box is not selected. This option should only be used in special cases when preparing the installation of devices which are not connected to the field bus. See next page for further information.

1. Select a device

3. The device appears in the Selected Devices pane

2. Click this button



Show FCU Slave Positions

You can associate a tank to a device which is not installed yet as long as it is configured in the FCU slave database. This may be useful if you for example have planned to install the device at a later time (or when an Echowave transmitter is connected to the FCU).

1. Select the Show FCU Slave Positions check box to display symbols which correspond to the FCU slave database.

2. Select the icon that corresponds to the FCU Slave Database position in question. In this example, the symbol named FCU-1.05 corresponds to position 5 in the FCU Slave Database as illustrated above.

3. Move the selected item to the Selected Devices pane by clicking the appropriate arrow button.

NOTE!You may verify the settings by clicking the Advanced button in the Tank Configuration window.

Step 4. Configure the tank.

The Tank Configuration window lets you specify analog input signals for Vapor Temperature, Vapor Pressure, Liquid Pressure, and Free Water Level (FWL) to be used for inventory calculations. See WinOpi User´s Guide for more information on Inventory Parameters.




NOTE!For LPG tanks the Vapor Temperature source and Vapor Pressure source are configured in LPG Setup (Service/Devices/LPG Setup).

The Calculate in TankMaster check box may be used for devices without internal calculation of Level Rate. By selecting this check box the Level Rate is calculated by the TankMaster program.

Vapor Temperature and Vapor Pressure are included in the calculation of Observed Density. Use the Inventory Parameters description in WinOpi User´s Guide for guidance.

A Rosemount TankRadar Rex gauge is equipped with two analog inputs. The free water level can for example be obtained from a Water Level Sensor connected to the Analog Input as illustrated below:

Free water level

Pressure

Water Level Sensor (WLS)

4-20 MA AIn (0)AIn (1)



Advanced Configuration

WinSetup allows you to change the mapping between tank and transmitter parameters. This option can for example be used if the Level value is temporarily provided by another measurement instrument connected to the Analog Input of the Radar Tank Gauge. It is also possible to connect temperature sensors from different tanks to the same DAU. Then you can configure the tanks to fetch temperature values from different channels of the DAU.

NOTE!This option should only be used when the standard Tank Configuration can´t be used.

To change the tank parameter mapping do the following:

1. Click the Advanced button in the Tank Configuration window.

This window lets you change the mapping between measured values and tank variables.

2. Put the mouse pointer in the output field corresponding to the variable you want to configure (Level, Level rate etc.).

3. Select the desired variable from the pop-up list.4. Click the OK button.

You can change source of any tank input variable. The following example illustrates how one DAU may be used to connect temperature sensors from two different tanks:




Example

Tanks TK-1 and TK-5 are equipped with three temperature sensors each.

TK-1 has one DAU (TT-1) configured for six temperature sensors.

The temperature sensors from both TK-1 and TK-5 are connected to DAU TT-1.

Configuration of tank TK-1.Tank TK-1 has the three temperature sensors connected to DAU TT-1. The sensors are mapped from output TT(0) to TT(2). Note that only three temperature sensors are connected, although the DAU is configured with six sensors.

Configuration of tank TK-5.The three temperature sensors are connected to DAU TT-1. In this case the sensors are mapped to output TT(3), TT(4) and TT(5).



Step 5. Value entry.

This window can be used to disconnect the automatic measurement if you for example want to set manual values for service purposes.

To set manual values do the following:

1. Chose a measurement variable from the left-hand list.2. Select Value Source/Manual.3. Type the desired value in the Value entry field.

Now the automatic measurement is disabled for the selected variable. Manual values are marked in yellow in order to distinguish them from automatically measured values.

The Value Range parameters (Minimum and Maximum) are used to scale bar graphs in the Tank View window and other windows (in Winsetup as well as WinOpi) where bar graphs are used to display product levels. For example, the Value Range maximum value for Level should be set equal to the Tank Reference Height, or the maximum level in the strapping table, to get correct scaling of the level bargraphs as illustrated below:

Value range:Min=0Max=20 m

Value range:Min=0Max=12 m




Step 6. Summary

This window shows information concerning the current tank installation. If you choose to click the Finish button, the tank installation is completed and the tank appears in the WinSetup Workspace. You can choose not to complete the installation by clicking the Cancel button. However, if a device was installed as part of the tank installation process, the device remains installed and appears in the Workspace although the tank installation is not completed.

NOTE!If a device installation was started during the tank installation but interrupted before the installation was finished, the communication address in the actual device may have been changed!

Name of the current tank

Associated devices



3.5.4 Summary of Tank Installation and Configuration

Tank TypeChoose the option that corresponds to the type of tank you are installing: Fixed Roof, Floating Roof, LPG Sphere, LPG Horizontal, Sphere, Horizontal, HTG Fixed Roof, HTG Floating Roof, or HTG Floating Blanket.

Select DevicesChoose the level gauge to associate with the tank. If the gauge is not installed yet, click the Install New Device button to install devices for this tank.

Tank ConfigurationSpecify the sources to act as input for Vapor Temperature, Vapor Pressure, Liquid Pressure, and Free Water Level (FWL).

Value EntryThis window lets you set manual values by disconnecting the automatic measurement. You can also set the value range for scaling of measurement variables in bar graphs.




3.5.5 To Change Tank Configuration

Once you have installed and configured a tank, you can modify the current settings at any time by opening the corresponding Properties dialog. To open the Properties dialog for a tank do the following:

1. In the Workspace window select the desired tank.

2. Click the right mouse button and select Properties from the popup menu.

3. Now the properties window appears with a number of tabs allowing you to change the current tank settings.

Basically the tabs correspond to the different steps in the installation wizard. See “Tank Installation” on page 3-30 for a description on how to configure a tank.

Properties



3.5.6 To Uninstall a Tank

To remove a tank from the WinSetup workspace do the following:

1. In the Workspace window select the tank you want to remove.

2. Click the right mouse button and select Uninstall from the popup menu.

NOTE!A device can only be uninstalled if the associated tank is uninstalled first.

Uninstall




3.6 DEVICE INSTALLATION - OVERVIEW

A Rosemount TankRadar REX system may include the following devices:• Field Communication Units (FCU) to collect measured data from Level

Gauges and Data Acquisition Units.• Gauges to measure product levels. Analog instruments, relays and

temperature sensors may be connected to a REX gauge.• Data Acquisition Units (DAU) for connecting temperature sensors.

Supported devicesThe WinSetup program supports installation and configuration of all device types that can be used in a Rex system:

• TankRadar Rex 3900• TankRadar Pro• Field Communication Unit (FCU)• Data Acquisition Unit (DAU)• IOT• TRL PU• Enraf CIU• Endress & Hauser MDP2

(TankMaster also supports old device types such as the RTG TRL/2 2900).

ConfigurationIn a complete installation you have to configure the device specific parameters and setup the device for communication with the TankMaster workstation.

Gauge configuration includes specification of:• communication parameters• antenna type• analog outputs, analog inputs and relays• temperature sensors• tank distances• RTG geometry

DAU configuration includes temperature sensors and local display.



3.7 STARTING THE DEVICE INSTALLATION WIZARD

You can start the device installation wizard in several ways.In the workspace/logical view:

1. Select the Devices folder.

2. Click the right mouse button and choose Install New from the popup menu

- or -

from the File menu choose Install New/Device.

As an alternative you can use the following method:

1. Select the server where your system is installed.

2. From the File menu choose Install New/Device.




In the workspace/physical view:

See chapter 3.8 to 3.15 for detailed information on how to install different devices.

1. Select the server where your system will be installed.

2. From the File menu choose Install New/Device.



3.8 INSTALLING A REX 3900 GAUGE

3.8.1 Step 1: Start the device installation wizardStart the installation wizard as described in “Starting the Device Installation Wizard” on page 3-45.

3.8.2 Step 2: Select device type

1. Choose device type REX RTG (also referred to as RTG 3900). If a DAU is included in the installation, choose REX RTG and SDAU (2100).

2. Specify a name in the Tag input field. TankMaster automatically suggests the first part of the name according to the settings in the Tag Prefixes window, see “Setting the Name Tag Prefixes” on page 3-18.





3.8.3 Step 3: Communication setup

Communication settings

There are two ways to connect to the RTG:• via a Field Communication Unit (FCU), or • directly via a Field Bus Modem (FBM).

Select the button that corresponds to the current type of connection. If a DAU is part of the installation, also set the DAU Modbus address.

In the FCU Slave Database each device is represented by one row and a unique address. The Slave Database contains information such as address, number of temperature sensors etc.. When the communication address is set for the current device, you should check that the value in the Position in FCU field corresponds to the actual position in the FCU Slave Database. If the Slave Database position seems to be wrong, it may indicate that you have chosen the wrong communication address. See “Position in FCU” on page 3-50 and “Installing a Field Communication Unit (FCU)” on page 3-23 for more information on the FCU Slave Database.

If there are several FCUs available choose the one that the gauge is connected to in the FCU Tag box.

For devices connected directly to the FBM (i.e. not via a FCU), select the channel that the FBM is connected to. (To check which channel that is enabled, open the Protocols folder, select the Master Protocol icon, click the right mouse button and choose Properties).

REX RTG

REX RTG and DAU



To change transmitter address1. Click the Change Address on Device button.

2. Enter the Unit Id of the current RTG and choose the desired address. When changing the device address, the Unit Id is used as a unique identifier of the device. The Unit Id can be found on a label mounted on the device.

(If there is no other device connected that uses the same address as the current device, you can find the Unit Id by typing the current address into the Address field and clicking the Verify Communication button in the Communication window).


4. In the Communication window click the Next button to open the Rex Configuration window.




Position in FCU

If the gauge is connected to an FCU, check that the Position in FCU field displays the correct number. This number must correspond to the position in the FCU Slave Database as illustrated below.

The current RTG isconfigured in position 1 in the FCU Slave Database.

The address of the current RTG corresponds to the address in position 1 of the FCU Slave Database.



3.8.4 Step 4: RTG Configuration

For a gauge connected via FCU, check that the presented number of temperature inputs corresponds with the number defined in the FCU slave database. Up to six temperature sensors can be connected to a Rex gauge. If a Rex gauge is connected to an associated DAU, no temperature sensors can be connected to the transmitter head. In this case all sensors have to be connected to the DAU.

For a standalone system, set the number of temperature sensors to be connected to the gauge in the Number of Temperature Inputs field.

NOTE!Make sure that the number of temperature sensors specified in the Number of Temperature Inputs field is equal to the number of sensors connected to the gauge.

Antenna type

You can choose one of the predefined antenna types, for example Parabola or Cone, or User Defined for non-standard antennas. For a predefined antenna a number of transmitter parameters such as TCL and Hold Off Distance (see “Step 6: RTG Geometry” on page 3-65) are automatically specified in order to optimize measurement performance. When choosing a user defined antenna you will have to make sure that the database settings are correct.




Choose one of the following antennas for the different gauge types:

RTG 3920• Cone 3920

RTG 3930• Parabolic 3930• Parabolic 3930 /P

RTG 3950• Still-Pipe array, fixed 3950• Still-Pipe array, hatch 3950 (not used)• Still-Pipe array, inclined 3950

RTG 3960

Depending on flange rate choose one of the following options:• LPG 150 PSI + Valve• LPG 150 PSI• LPG 300 PSI + Valve• LPG 300 PSI• LPG 600 PSI + Valve• LPG 600 PSI

To configure a User Defined antenna

The User Defined options (User Def. Free Propagation, User Def. Linear Pipe, and User Def. Modeconv. Pipe) should only be used in special situations when non-standard antennas are used.

1. Choose the appropriate antenna type:• User Def. Free Propagation• User Def. Linear Pipe• User Def. Modeconv. Pipe• User Def. Pipe Array

2. For a still-pipe, enter the inner diameter in the Pipe Diameter field.3. Specify TCL and Hold Off Distance in the RTG Geometry window, see

“Step 6: RTG Geometry” on page 3-65.

When the Cone Antenna or the Parabolic Antenna is used, the pipe diameter is automatically set to -0.1 m since this parameter is irrelevant for these antennas.

NOTE!The User Defined options should only be used in special situations when non-standard antennas are used.



Remote Display Unit (RDU)

Select RDU40 if the gauge is connected to a RDU 40 display unit. When using a DAU the RDU40 must not be selected.

The 2210 Display Unit is used for Pro gauges.

Select the Use System Units check box if you want the RDU 40 or 2210 Display Unit to use the measurements units specified in the System Setup window (see “Preferences” on page 3-14).

Temperature Sensor Configuration

In the Rex Configuration window click the Temp Input button to configure type, range and position of the temperature sensors.

Sensor Type

You can choose between the following sensor types:• Spot DIN Pt100.• Cu90 (average measurement)• User-defined. The characteristics is specified by a mathematical

formula or a linearization table. (See “User Defined Temperature Conversion” on page 8-4 for more information about specifying a user-defined sensor type).

NOTE!See the Rex Service Manual for more information on temperature measurement.

Make sure that you choose the correct sensor type. For Spot and Multiple Spot temperature elements you have to choose the Spot Pt100 sensor type in order to obtain a correct average temperature calculation.




Sensor Range

The following temperature range is available:• -50 to +250 °C.• User Defined. This option should not be used for standard sensors.

Contact Emerson Process Management / Rosemount Tank Gauging for information if you need to use temperature sensors for non-standard temperature range.

Sensor Position

The sensors are numbered from the bottom of the tank and upwards. Enter the position of each sensor, measured as the distance from the Zero Level (Dipping Datum Plate) to the temperature element. If you use average temperature elements enter the position of the terminating level of each sensor element.

NOTE!The number of available sensors is specified in the Rex Configuration window.

Average Temperature Calculation

Select the Exclude From Average Calculation check box if you want to exclude a certain spot element from the average temperature calculation. This may be useful if, for example, the temperature close to the surface or close to the bottom of the tank deviates significantly from the temperature in the rest of the tank. This may also be accomplished by setting an appropriate value of the Minimum Distance parameter, see “Minimum Distance” on page 3-55.

NOTE!A faulty temperature sensor is blocked automatically, and consequently excluded from average temperature calculations.



Minimum Distance

You can specify a region between the product surface and a certain level below the surface, in which spot sensors will not be included in the average temperature calculation. The width of this region is specified by setting the Minimum Distance.

This function may be useful if the temperature of the atmosphere above the product significantly deviates from the temperature of the product itself, resulting in large temperature gradients close to the product surface. By setting a Minimum Distance, temperature elements within this region can be excluded from average temperature calculations.

This function can also be used to compensate for inaccuracies in the measured sensor positions, in order to make sure that temperature sensors above the product surface are not included in the average temperature calculation. If for example the positions of the temperature sensors is measured within an accuracy of 10 mm, setting the minimum distance to at least 10 mm will guarantee that sensors above the surface are not included in the average temperature calculations.

MINIMUM DISTANCE

These sensors are not included in the average temperature calculation

Product surface




Configuration - Analog Inputs

To configure connected analog input signals click the appropriate Analog Input button (Analog Input 1/2) in the REX RTG Configuration window.

Value range

Enter the lower and upper limits corresponding to the 4 mA and 20 mA input currents, respectively.

Error limits

The error limits define the lower and upper limits of the input currents. Outside this range an error will be indicated. You can set the upper error limit between 20 and 24 mA, and the lower error limit between 3 and 4 mA. The error limits should be set to correspond to the error limits of connected instruments. If for example an instrument sets the output current in alarm mode to 3.8 mA, you should set the lower error limit to 3.8 or higher.

Value unit

Choose a suitable measurement unit. You can choose between various units to indicate pressure (mBar G, mBar A), product level, and current.

Filter factor

By setting a filter factor you can suppress spurious fluctuations in the analog input signal. A value between 1 and 200 can be used. The default value is 4.

Description

Enter an optional Description of the Analog Input.



Configuration - Analog Outputs

To configure the analog output signal, click the Analog Output button in the Rex RTG Configuration window.

Analog Out Source

Choose the desired source signal for the Analog Output. If, for example, AOut Source=Level, the REX gauge provides an analog output signal between 4 and 20 mA which is proportional to the current product level.

Alarm mode

The Alarm mode specifies the analog output state when a measurement error occurs, or when the measured value is out of range:

• High: the output current is set to 22 mA.• Low: the output current is set to 3.8 mA.• Freeze current: the output current is set to the present value at the time

when the error occurs.• Binary High: the output current is 4 mA under normal conditions. If

there is a measurement error, or when the source signal is out of range, the output current is set to 20 mA.

• Binary Low: the output current is 20 mA under normal conditions. If there is a measurement error, or when the source signal is out of range, the output current is set to 4 mA.

Range Value

Set the source signal values that correspond to the analog output values 4 mA and 20 mA, respectively. You can specify any value as long as the Upper range value is above the Lower range value. If the measured value goes out of range, the transmitter enters the alarm mode.




Configuration - Relay Output

To configure connected relays, in the REX RTG Configuration window click the appropriate Relay Output button.

The optional Relay Output Card at the underside of the transmitter head, allows you to use one or two relays. There are two connectors for each relay (X2-X3 and X4-X5) which can be used to specify relay state On or Off when it is not energized.

If the transmitter is connected to an FCU, check that the Slave Database is configured with the correct number of relays. See “Installing a Field Communication Unit (FCU)” on page 3-23 for more information.

Using first/both points

Select Use Both Points if you want to define three relay zones.

Select Use Only First Point if you want to use only two relay zones.

First and second set points

The first and second set points define the transitions between Zone 1, 2 and 3. You can set different relay states in each of these zones.

Hysteresis

When the source variable passes a set point, the relay switches from one state to the other. If a hysteresis zone is specified, the relay remains in the new state until the source signal has changed back to a value below the set point and the hysteresis point. Thus, the actual set point is given by the combination of set point (First Point/Second Point) and the value given in the Hysteresis input field (see also “Relay Functions” on page 3-61).



Relay states

There are three relay states available:

Select SourceSpecifies the transmitter variable that triggers the switching of the relay.

Switch DelayThis is the time delay until the relay switches into alarm state, i.e. the amount of time it takes for a relay to respond to an alarm. You can use this to prevent the relay from being activated due to temporary variations of the source signal.

Toggle PeriodWhen the relay is in Toggle state it switches between On and Off at a rate defined by the Toggle Period.

Control Mode

Alarm In this state the relay is de-energized. Depending on how the relays are connected to X2-X3 (relay 1) and X4-X5 (relay 2) on the Relay Output Card (ROC), they will be either open or closed in the de-energized state.Note that a relay defined as Normally Open will be open in the Alarm state.If the relay is configured as Normally Closed it will be closed in the Alarm state.

Normal In this state the relay is energized.

Toggle The relay switches periodically between Normal and Alarm

Manual the relay state is set manually by using the Manual Control Relay option from the Service/Devices menu.

Auto the relay state is controlled by the transmitter variable specified in the Select Source field.

Disabled the relay function is turned off.

X2

X3

X4

X5

The Relay Output Card




Relay output configuration

The relay output can be selected as either Normally Open or Normally Closed referring to the contact position when the relay is de-energized. This also refers to the Alarm (Reset) state. By connecting relay 1 to connector X2 on the Relay Output Card (ROC), the relay is set as Normally Closed. Connecting to X3 sets the relay as Normally Open. See the TankRadar REX Installation Manual for further information.

The relay terminology can be summarized the following way:

Example

You want relay 1 to be Open during normal operation and to be Closed when in alarm mode. This means that the relay is de-energized when there is an alarm and consequently the relay has to be connected as Normally Closed. On the Relay Output Card this corresponds to the X2 connector. See the Rex Installation Manual for more information on how to connect the Rex transmitter relays.

Normally Closed Normally Open

Closed Open Open Closed

De-energized Energized De-energized Energized

Not Active Active Not Active Active

Alarm (Reset) Normal Alarm (Reset) Normal



Relay Functions

You can use one or two set points for relays connected to the Rex transmitter. Consequently, there are two or three zones in which different relay states can be specified. For each zone you can set any of the three available relay states Normal, Alarm or Toggle.

For each set point you can specify a hysteresis zone preventing the relay from switching back to its previous state as long as the source variable is changed only small amounts around a certain set point. The principle of relay set points and hysteresis zones is shown in the figure below. Note that in this example only two states are used:

1. The source value passes set point one, and the relay state is changed according to the definition for Zone 1.

2. The relay state is changed back to the Zone 2 state when the source value passes the set point as given by the hysteresis value.

3. The source value passes set point two and the relay state is changed according to the definition for Zone 3.

4. The relay switches back to the Zone 2 relay state when the source value passes set point two as given by the corresponding hysteresis value.

Rel

ay s

tate

Time

ZONE 1

ZONE 2

ZONE 3

Sour

ce s

igna

l

1

2

3

4

Relay State Zone 1

Relay State Zone 2

Relay State Zone 3

Relay State Zone 2

Hysteresis zone

Hysteresis zone




Hart Devices Configuration

Up to three HART slaves can be connected to Analog Input 1 using address 1-3, see Rex Installation Manual. In this case the current is set to 4 mA.

In Analog Current mode only one HART slave is allowed. In this case address 0 must be used.

To configure connected devices using the HART protocol click the HART Devices button in the RTG Rex Configuration window.

A Rex gauge can act as a master interfacing up to three HART devices (slaves) in a multidrop configuration connected to Analog Input 1. When two or three HART slaves are connected short address 1-3 must be used.

The HART Devices Configuration window lets you specify an identifier for each HART slave.

If the transmitter is connected to an FCU, check that the Slave Database is configured with the correct number of HART slaves. See “Installing a Field Communication Unit (FCU)” on page 3-23 for more information.

To view status information of connected HART slaves choose HART Devices Status from the Service/Devices menu.

Tank Scan

To open the Tank Scan window, press the Tank Scan button in the Rex RTG Configuration window. For a description of the Tank Scan window and its functionality, see “Tank Scan” on page 8-13.



3.8.5 Step 5: Tank Distances

The following tank distance parameters need to be specifed (see also “Tank Distances” on page 3-64):

Tank Reference Height (R)

The Tank Reference Height (R) is the distance from the hand dipping nozzle (Tank Reference Point) to the Zero Level (Dipping Datum Plate) close to or at the bottom of the tank.

Rex Reference Distance (G)

The RTG Reference Distance (G) is the distance between the Tank Reference Point and the RTG Reference Point, which is located at the top surface of the customer’s flange or manhole cover on which the gauge is mounted. For Still Pipe Gauges the RTG Reference point is located at the hand-dip mark on the Still Pipe Gauge Stand.

G is positive if the Tank Reference Point is located above the RTG Ref Point. Otherwise G is negative.

Minimum Level Distance (C)

The Minimum Level Distance (C) is defined as the distance between the Zero Level (Dipping Datum Point) and the Minimum Level of the product surface (tank bottom). By specifying a C-distance, the measuring range can be extended to the bottom of the tank. If C>0, negative level values will be displayed when the product surface is below the Zero Level. Select the Show negative level values as zero check box if you want levels below the Zero Level to be displayed as Level=0.

Measurements below the Zero Level will not be approved if the C-distance=0, i.e. the RTG will report an invalid level.




Tank Distances

TANK REFERENCE POINT

TAN

K R

EFER

ENC

E H

EIG

HT

(R)

ZERO LEVEL

MINIMUM LEVEL DISTANCE (C)

RTG REFERENCE POINT

HOLD OFF DISTANCE

APP

RO

VED

MEA

SUR

ING

RA

NG

E

RTG Reference Distance (G)

Minimum Level

Definition of tank distances.

Tank Height (R) Distance from Tank Reference Point to Zero level

RTG Reference Distance (G) Distance from Tank Reference Point to the RTG Reference Point

Minimum Level Distance (C) Distance from Zero Level to tank bottom

Hold Off Distance Defines how close to the RTG Reference Point levels can be measured

Definition of G-distance.

G>0

G<0



3.8.6 Step 6: RTG Geometry

Tank Connection Length (TCL)

The TCL can only be changed for antenna type User Defined (see the Rex Configuration window). For standard antennas such as the Parabolic, Cone etc. a predefined TCL value is used which can not be changed.

The TCL does not correspond to the physical length of the tank connection. It is specified for each antenna individually. For User Defined antennas, the gauge can be calibrated by adjusting the TCL value.

Standard antennas have predefined TCL values which can not be changed in the REX RTG Geometry window. With predefined antenna types (selected in the Rex Configuration window), the gauge can be calibrated by adjusting the Calibration Distance, see “Calibration” on page 3-120.

Hold Off Distance/UFM

The Hold Off distance/UFM defines how close to the RTG Reference Point a level value is accepted. Normally the Hold Off distance does not need to be changed. However, if there are disturbing echoes in the upper part of the tank, for example from the tank nozzle, you can increase the Hold Off distance in order to avoid measurements in the region close to the antenna.

Calibration Distance

Use this variable to adjust the transmitter so that measured product levels match hand dipped levels. Normally a minor adjustment is necessary when the gauge is installed due to, for example, a minor deviation between the actual tank height and the value stored in the transmitter database.




3.8.7 Step 7: DAU Configuration

NOTE!This step is only required if you are installing a DAU.

To configure the Data Acquisition Unit (DAU) do the following:

1. In the RTG Geometry window click the Next button. The REX RTG DAU Configuration window appears:

2. Click the Synchronize with FCU button. This will update the number of temperature inputs as specified in the FCU Slave Database window, see “Installing a Field Communication Unit (FCU)” on page 3-23.

3. Select the analog input signal to appear on the DAU local display. Ain designates current inputs to a REX Radar Tank Gauge (RTG).

4. Click the Configure button to configure the temperature sensors.



Temperature sensor configuration

Up to 14 temperature sensors can be connected to a DAU. To configure the temperature sensors do the following:

1. In the DAU Configuration window click the Configure button next to the Number of Temperature Sensors field. The Temperature Sensors Configuration window appears:

2. Type the position of each sensor in the corresponding input field.3. Select the appropriate sensor type and measuring range.4. if you want to exclude a particular temperature sensor from the average

temperature calculation, select the Average Exclude check box . This may be useful if for example a sensor is broken, or if the temperature close the surface or the bottom of the tank deviates significantly from the temperature in the rest of the tank. (The sensor will also be marked as blocked in Tankmaster WinOpi).

5. Click the OK button to return to the DAU Configuration window.

SENSOR TYPE

SENSOR RANGE

Temperature sensor position




3.8.8 Step 8: Summary 1. Click the Next button to continue.

The Summary window shows information concerning the current device installation. If you choose to click the Finish button, the installation is completed and the installed devices appear in the WinSetup Workspace. You can choose not to fulfill the installation by clicking the Cancel button.

NOTE!If the communication address was changed during the installation procedure, the new address remains stored in the actual device even if the installation was interrupted and the device is not visible in the WinSetup Workspace!

2. Check that the displayed information is correct and click the Finish button to finish the installation.



Summary of REX RTG Installation and Configuration

Device typeSelect device type REX (or REX and SDAU if the system includes a slave DAU).

CommunicationAssign the address and specify if the workstation should communicate directly to the connected device or via a Field Communication Unit (FCU).

ConfigurationSpecify antenna type. Configure temperature sensors and optional facilities like relay outputs, analog inputs and HART master.




Tank DistancesSpecify the tank distances needed for converting measured quantity (ullage) into product level.

RTG GeometrySpecify gauge related parameters for calibration and optimizing measurement performance.

DAU ConfigurationConfigure temperature sensors and local display (LCD).



3.9 INSTALLING A PRO GAUGE

3.9.1 Step 1: Start the device installation wizardStart the installation wizard as described in “Starting the Device Installation Wizard” on page 3-45.

3.9.2 Step 2: Select device type

1. Choose device type Pro RTG. If a DAU is part of the installation, choose Pro RTG and IDAU.

2. Specify a name in the Tag input field. TankMaster automatically suggests the first part of the name according to the settings in the Tag Prefixes window, see “Setting the Name Tag Prefixes” on page 3-18.





3.9.3 Step 3: Communication setup

Communication settings

There are two ways to connect to the RTG:• via a Field Communication Unit (FCU), or • directly to the RTG via a Field Bus Modem (FBM).

Select the button that corresponds to the current type of connection. If a DAU is part of the installation, also set the DAU Modbus address.

In the FCU Slave Database each device is represented by one row and a unique address. The Slave Database contains information on each device such as address, number of temperature sensors etc. (see “Installing a Field Communication Unit (FCU)” on page 3-23).

When the communication address is set for the current device, you should check that the value in the Position in FCU field corresponds to the desired position in the FCU Slave Database. If the Slave Database position is incorrect, it may indicate that you have set the wrong address for the current device.

If there are several FCUs available choose the one that the gauge is connected to in the FCU Tag box.

For devices connected directly to the FBM (i.e. not via a FCU), select the channel that the FBM is connected to. (To check which channel that is enabled, open the Protocols folder, select the Master Protocol icon, click the right mouse button and choose Properties).



To change transmitter address

1. Click the Change Address on Device button.

2. Enter the Unit Id of the current RTG and choose the desired address. When changing the device address the Unit Id is used as a unique identifier of the device. It can be found on a label mounted on the device.

(If there is no other device connected that uses the same address as the current device, you can find the Unit Id by typing the current address into the Address field and clicking the Verify Communication button in the Communication window).


4. In the Communication window click the Next button to open the Pro Configuration window.




Position in FCU

If the gauge is connected to an FCU, check that the Position in FCU field displays the correct number. This number must correspond to the position in the FCU Slave Database as illustrated below.

The current RTG isconfigured in position 2 in the FCU Slave Database.

The address of the current RTG corresponds to the address in position 2 of the FCU Slave Database.



3.9.4 Step 4: RTG Configuration

The number of temperature sensors connected to the gauge is set in the FCU slave database. Up to six temperature sensors can be connected to a Pro gauge.

NOTE!Make sure that the number of temperature sensors specified in the Number of Temperature Inputs field is equal to the number of sensors connected to the gauge.

Antenna type

You can choose one of the predefined antenna types, for example Parabola or Cone, or a User Defined antenna if your antenna is not available among the predefined antenna types. For a predefined antenna a number of transmitter parameters such as TCL and Hold Off Distance (see “Step 6: RTG Geometry” on page 3-65) are automatically specified in order to optimize measurement performance. When choosing a user defined antenna you will have to make sure that the database settings are correct.




The following antenna types are available:• User defined• Cone 4" PTFE• Cone 4" QUARTZ• Cone 6" PTFE• Cone 6" QUARTZ • Cone 8" PTFE• Cone 8" QUARTZ • Pipe PTFE• Pipe QUARTZ • Rod• Parabola• Process Seal 4" PTFE• Process Seal 4" Ceramic• Process Seal 6" PTFE• Process Seal 6" Ceramic• Cone 3" PTFE• Cone 3" QUARTZ• ITG Stillpipe 6”• ITG Stillpipe 8”• ITG Stillpipe 10”• ITG Stillpipe 12”• Stillpipe Array Flanged• Stillpipe Array Hatched• Rod 100• Rod 250

To configure a User Defined antenna

The User Defined option should only be used in special situations when non-standard antennas are used.

1. Choose the appropriate antenna type.2. For a still-pipe, enter the inner diameter in the Pipe Diameter field.3. Specify TCL and Hold Off Distance in the RTG Geometry window, see

“Step 6: RTG Geometry” on page 3-65.

When the Cone Antenna or the Parabolic Antenna is used, the pipe diameter is automatically set to -0.1 m since this parameter is irrelevant for these antennas.

NOTE!Except for Still-Pipe gauges the User Defined options should only be used in special situations when non-standard antennas are used.



Temperature Sensor Configuration

In the Pro Configuration window click the Temp Input button to configure type, range and position of the temperature sensors.

Sensor TypeYou can choose between the following sensor types:

• Spot DIN Pt100.• Cu90 (average measurement)• User-defined. The characteristics is specified by a mathematical

formula or a linearization table. (See “User Defined Temperature Conversion” on page 8-4 for more information about specifying a user-defined sensor type).

Make sure that you choose the correct sensor type. For Spot and Multiple Spot temperature elements you have to choose the Spot Pt100 sensor type in order to obtain a correct average temperature calculation.

Sensor RangeSpecify the sensor temperature range.

Sensor PositionThe sensors are numbered from the bottom of the tank and upwards. Enter the position of each sensor, measured as the distance from the Zero Level (Dipping Datum Plate) to the temperature element. If you use average temperature elements enter the position of the terminating level of each sensor element.

NOTE!The number of available sensors is specified in the Pro Configuration window.




Average Temperature Calculation

Select the Exclude From Average Calculation check box if you want to exclude a certain spot element from the average temperature calculation. This may be useful if, for example, the temperature close to the surface or close to the bottom of the tank deviates significantly from the temperature in the rest of the tank. This may also be accomplished by setting an appropriate value of the Minimum Distance parameter.

NOTE!A faulty temperature sensor is blocked automatically, and consequently excluded from average temperature calculations.

Minimum Distance

You can specify a region between the product surface and a certain level below the surface, in which spot sensors will not be included in the average temperature calculation.

The width of this region is specified by setting the Minimum Distance.

This function may be useful if the temperature of the atmosphere above the product significantly deviates from the temperature of the product itself, resulting in large temperature gradients close to the product surface. By setting a Minimum Distance, temperature elements within this region can be excluded from average temperature calculations.

This function can also be used to compensate for inaccuracies in the measured sensor positions, in order to make sure that temperature sensors above the product surface are not included in the average temperature calculation. If for example the temperature sensor positions are measured at an accuracy of 10 mm, setting the minimum distance to 10 mm or more makes sure that sensors above the surface are not included in the average temperature calculations.

MINIMUM DISTANCE

These sensors are not included in the average temperature calculation

Product surface



Configuration - Analog Outputs

To configure the analog output signal, click the Analog Output button in the Pro RTG Configuration window.

Analog Out Source

Choose the desired source signal for the Analog Output. If, for example, Level is selected the Analog Output provides an output signal between 4 and 20 mA which is proportional to the current product level.

Alarm mode

The Alarm mode specifies the analog output state when a measurement error occurs, or when the measured value is out of range:

• High: the output current is set to 22 mA.• Low: the output current is set to 3.8 mA.• Freeze current: the output current is set to the present value at the time

when the error occurs.• Binary High: the output current is 4 mA under normal conditions. In

case there is a measurement error, or when the source signal is out of range, the output current is set to 20 mA.

• Binary Low: the output current is 20 mA under normal conditions. In case there is a measurement error, or when the source signal is out of range, the output current is set to 4 mA.

Range ValueSet the source signal range values that correspond to the analog output values 4 mA and 20 mA. You can specify any value as long as the Upper range value is above the Lower range value. If the measured value goes out of range, the transmitter enters the alarm mode.




3.9.5 Step 5: Tank Distances

The following tank distance parameters need to be specifed (see also “Tank Distances” on page 3-81):

Tank Reference Height (R)

The Tank Reference Height (R) is the distance from the hand dipping nozzle (Tank Reference Point) to the Zero Level (Dipping Datum Plate) close to or at the bottom of the tank.

Pro Reference Distance (G)

The Pro Reference Distance (G) is the distance between the Tank Reference Point and the RTG Reference Point, which is located at the top surface of the customer’s flange or manhole cover on which the gauge is mounted. For still-pipe gauges the RTG Reference point is located at the hand-dip mark on the still-pipe gauge stand.

G is positive if the Tank Reference Point is located above the RTG Reference Point. Otherwise G is negative.

Minimum Level Distance (C)

The Minimum Level Distance (C) is defined as the distance between the Zero Level (Dipping Datum Point) and the Minimum Level of the product surface (tank bottom). By specifying a C-distance, the measuring range can be extended to the bottom of the tank. If C>0, negative level values will be displayed when the product surface is below the Zero Level. Select the Show negative level values as zero check box if you want levels below the Zero Level to be displayed as Level=0.

If you set the C-distance=0, measurements below the Zero Level will not be approved, i.e. the RTG will report an invalid level.



Tank Distances

TANK REFERENCE POINT

TAN

K R

EFER

ENC

E H

EIG

HT

(R)

ZERO LEVEL

MINIMUM LEVEL DISTANCE (C)

RTG REFERENCE POINT

HOLD OFF DISTANCE

APP

RO

VED

MEA

SUR

ING

RA

NG

E

RTG Reference Distance (G)

Minimum Level

Definition of tank distances.

Tank Height (R) Distance from Tank Reference Point to Zero level

RTG Reference Distance (G) Distance from Tank Reference Point to the RTG Reference Point

Minimum Level Distance (C) Distance from Zero Level to tank bottom

Hold Off Distance Defines how close to the RTG Reference Point levels can be measured

Definition of G-distance.

G>0

G<0




3.9.6 Step 6: RTG Geometry

Tank Connection Length (TCL)The Tank Connection Length (TCL) is specified for each antenna individually. Each standard antenna has a predefined TCL value which does not correspond to the physical length of the Tank Connection. TCL can only be changed for antenna type User Defined (see the Pro Configuration window). If you chose one of the predefined antennas in the Pro Configuration window, you can calibrate the transmitter by adjusting the Calibration Distance.

Hold Off Distance/UFMThe Hold Off distance/UFM defines how close to the RTG Reference Point a level value is accepted. Normally the Hold Off distance does not need to be changed. However, if there are disturbing echoes in the upper part of the tank, for example from the tank nozzle, you can increase the Hold Off distance in order to avoid measurements in the region close to the antenna.

Calibration DistanceUse this variable to adjust the transmitter so that measured product levels match hand dipped levels. Normally a minor adjustment is necessary when the gauge is installed due to, for example, a minor deviation between the actual tank height and the value stored in the transmitter database.



3.9.7 Step 7: Summary 1. In the Pro RTG Geometry window click the Next button to continue.

2. Click the OK button to finish the Pro RTG installation.




3.10 INSTALLING A TRL PU

Preparations

Make sure that the RS232 connector is properly jumpered:

Check the Master Protocol configuration (see “Master Protocol Channel Configuration” on page 3-5). Configure the communication parameters as follows:

Configuration

1. Start the device installation wizard, see “Starting the Device Installation Wizard” on page 3-45.

2. Choose device type TRL PU and click the Next button to continue.

3. Select the Communication channel that the modem is connected to. (To check which channel is enabled, open the Protocols folder, select the Master Protocol icon, click the right mouse button and choose Properties).

4. Enter the TRL PU Modbus address. The address can be viewed in directory 72 on the TRL Display Panel Unit. Normally address 1 or 34 is used.

5. Click the Verify Communication button to make sure that communication with the TRL PU unit is established. Click the Next button to continue.

Modem RS232.Handshaking None.Baud Rate See Directory 72 on the PU Display Unit.Stop Bits See Directory 72 on the PU Display Unit.Parity See Directory 72 on the PU Display Unit.

1

6 7 8 9

2 3 4 5 Jumpers between pins 1, 4, and 6.

Jumpers between pins 7 and 8.



6. Make sure that the maximum number of gauges is equal to the number of tanks.

7. Enter the number of temperature inputs for each gauge. Use the TRL Display Panel Unit (DPU) to see in which order the TRL gauges are listed. (See the TRL Operator´s Manual for details on how to use the DPU).

8. Select the corresponding check box for gauges equipped with pressure sensor.

9. Mark the Level source in cm check box if the TRL PU is equipped with the option for measuring tanks higher than 32 meters.

10. Mark the Level rate available check box if software version 1.df or later is used. The software version can be viewed in directory 60 on the TRL Display Panel Unit. Click the Next button to continue.

11. Click the Finish button to finish the TRL PU installation.




3.11 INSTALLING AN IOT WinSetup supports installation of four types of I/O Terminals (IOT):

The installation of an IOT using the installation wizard includes the following steps:

The following installation example shows how to install an IOT 5120. A similar procedur is used for the IOT 5110, 5130, and the IOT 5140.To install an IOT 5120 do the following:

1. Start the device installation wizard, see “Starting the Device Installation Wizard” on page 3-45.

2. Choose device type IOT 5120, and set an appropriate IOT tag. Click the Next button to continue.

IOT 5110 Analog Input 16 channelsIOT 5120 Analog Output 16 channelsIOT 5130 Digital Input 16 channelsIOT 5140 Digital Output 8 channels

IOT 5110 IOT 5120 IOT 5130 IOT 5140

Select Device Select Device Select Device Select Device

Communication Communication Communication Communication

Enable Channels Enable Channels Enable Channels Channel Mapping

Configuration Configuration Summary Summary

Scaling Scaling

Summary Channel Mapping

Summary



3. Select the Communication channel that the modem is connected to. (To check which channels are enabled, open the Protocols folder, select the Master Protocol icon, click the right mouse button and choose Properties).

4. Enter the IOT address.

5. Click the Verify Communication button to make sure that communication with the IOT unit is established. Click the Close button and then click the Next button to continue.

6. Select which channels to enable. By default all channels are enabled. Click the Next button to continue

Select Communication Channel

Enter IOT address

Verify communication




7. Configure the analog channels for the terminal. Select mA to configure the channel for 4-20 mA, or select Volt to configure the channel for 0-10 Volt. Click the Next button to continue.

8. Set the scaling parameters for each channel.• Configure the Scale Min and Scale Max range values,

e.g. 0-10 V.• Configure Value Min and Value Max for scaling, e.g. 0-20 m.• Choose Value Unit, e.g. m.

Click the Next button to continue.



9. This window shows the Channel Mapping for tank or system parameters to the active analog output channels. Click the button to select a source for the channel.

10. There are two ways you can configure the channel source - Simplified and Advanced.

In the Simplified configuration you can choose between tanks and system objects in the Use Source as combo box. After the source is selected you can choose parameter (for example Level, or Avg Temp) in the Parameter combo box. Only current value (CV) of the selected parameter can be used.

In the Advanced configuration you can select not only tanks and system objects, but also devices. Formally, any parameter and any field (i.e. not only current value) can be selected. However, the user is advised to use current value (CV).

Click the OK button to return to the Channel Mapping window.

Click here to select a source for Channel 1.




11. In the Channel Mapping window, click the Next button.

12. Click the Finish button to finish the IOT installation.



3.12 INSTALLING AN ENRAF CIU

To install a CIU do the following:

1. Connect the CIU to one of the COM ports on the TankMaster PC.

NOTEIf a CIU Prime is used, make sure that it is configured to emulate a CIU 858. Use the Enraf CIU Prime configuration program to set the check box “CIU 858 compatible” for the dedicated port (Host Port 2).

2. In the WinSetup workspace select the Enraf GPU Master icon, click the right mouse button and choose the Properties option. In the Protocol Properties window select the desired protocol channel and click the Properties button.

3. Check that the Protocol Channel is enabled and properly configured. See “Communication Protocol Setup” on page 3-4 for further information about how to configure communication protocols in WinSetup.

4. Start the device installation wizard as described in “Starting the Device Installation Wizard” on page 3-45.

5. Choose device type CIU in the Select Device window and type the desired name tag.




6. Click the Next button.

7. Select an enabled communication channel. (You can check which communication channels are enabled by opening the EnrafGPUMaster protocol folder in the WinSetup workspace).


9. Configure the CIU channels. Select the available parameters for each channel that is used. The Set values as selected row button lets you select or deselect all check boxes at one click.

The following parameters can be selected:



• Level• Average Temperature• Number of Temperature inputs• Vapor Temperature• Number of pressure inputs• Pressure Input 1 Unit (liquid)• Pressure Input 2 Unit (level)• Pressure Input 3 Unit (vapor)• Free Water Level (FWL)

Click the Next button.

10. In the Summary window click the Finish button to finish the TankMaster WinSetup part of the CIU installation.




3.12.1 Configuration of the Egpudev.ini file

1. Copy the Egpudev.ini file from the Misc folder on the TankMaster CD to the ...\Rosemount\Server\Data folder on the TankMaster PC.

2. Edit the Egpudev.ini file using a text editor, e.g. the Windows Notepad program. The Egpudev.ini file has the following contents:

1

23



The following is a short description of the contents in the Egpudev.ini file:

1. Device_0=1.0.CIU

2. DEVICE=UR:20000;TOI:R;TOR0:X;

3. CH0=ADDR:04;UR:3000;TOI:B;TOR0:D;TOR1:X;

The requested data is specified in this string. Note that the name of the first string is CH0, which corresponds to Channel no.1 in the CIU Properties/Configuration window. The commands are:

3. Save the edited Egpudev.ini file.

Device_0 Device number one. Next device is Device_1 etc. See Step 2 above.

1 Enraf GPU Master Protocol channel number

0 CIU address

CIU Device type (do not change)

UR Update Rate: 20000 ms (=20 s)

TOI:R Type of Instrument where R means CIU GPU-Protocol Version

TOR0:X Type of Request. X stands for Identity (send identity record)

CH0 Corresponds to Channel no.1 (first position in CIU Properties/Configuration window, see step 9 on page 3-92).

ADDR:04 The gauge address

UR:3000 Update Rate in ms (3000 ms= 3 s)

TOI:B Stands for Type Of Instrument; B means an 811 Gauge with GPU Protocol and devices with Gauge Type = B (854 servo is such a gauge). Rex can emulate a type B or C gauge.

TOR0:D Type of Request 1.D is Request for Level and Temp. This can for example also be B (Request for Level) or C (Request for Temp).

TOR1:X Type of Request 2. X stands for Identity (send identity record).




3.12.2 Configuration of an Enraf Gauge

The TankMaster WinSetup program can be used to configure Enraf GPU devices connected to a CIU.

To configure an Enraf device via a CIU do the following:

1. In the WinSetup workspace open the Devices folder.

2. Click the right mouse button on the CIU to which the gauge is connected. Choose the Properties option.

3. Select the Configure Device tab.4. Verify that the CIU address is correct (0-9).5. Enter the gauge address (0 - 99).6. Set type of instrument (TOI=B).7. Select the Z-type of Record check box if Z Type Of Request is used.8. Enter item (LQ = level query) by the "C:" sign.9. Press Enter.

Devices



Example 1

Sending a request for status and level (Type Of Request=B):

Example 2

Changing the Reference Level (Type Of Request=Z):

Z-type of Record check box




3.13 INSTALLING AN ENDRESS & HAUSER MDP 21. Make sure that the device is connected to one of the COM ports of the

TankMaster PC.2. In the WinSetup workspace, select the Modbus Master icon, click the

right mouse button and choose the Properties option. 3. In the Protocol Properties window select the desired protocol channel

and click the Properties button.

4. Check that the protocol channel is enabled and properly configured for E&H. See “Communication Protocol Setup” on page 3-4 for further information on how to configure communication protocols in WinSetup.

5. Start the device installation wizard as described in “Starting the Device Installation Wizard” on page 3-45.

6. Choose device type E&H MDP II in the Select Device window and type the desired name tag.




8. Select an enabled communication channel configured for E&H. (You can check which communication channels that are enabled by opening the ModbusMaster protocol folder in the WinSetup workspace).Click the Next button.

9. Configure the E&H channels by selecting the parameters (level and/or average temperature) to be used. Use the Clear button if you want to deselect all check boxes.Click the Next button.




10. In the Summary window click the Finish button to finish the E&H installation.



3.14 INSTALLING AN LPG/LNG TANK GAUGE

3.14.1 Preparations Make sure that all mechanical installations are made according to instructions, and that all external sensors such as pressure and temperature sensors are properly connected. Also make sure that the position of the reference pin(s) and the inner diameter of the still-pipe are available.

Before the actual LPG configuration can take place, install the tank and the level gauge in TankMaster WinSetup as described in “Tank Installation” on page 3-30 and “Installing a Rex 3900 Gauge” on page 3-47. Make sure that the appropriate tank and device types are selected and that the temperature and pressure sensors are properly configured. Check that the gauge communicates properly with the TankMaster PC.

The LPG gauge is able to compensate deviations in measured level due to the influence of highly pressurized vapor above the product surface. Installation of an LPG gauge can roughly be divided in two main activities:

1. Immediately after the installation of the gauge, when the tank is still empty, calibrate the gauge and configure for LPG.

2. Setup the correction method that applies to the particular type of product that is stored in the tank.




3.14.2 LPG Configuration

Step 1. Check the ball valve.

Check that the optional ball valve on the gauge is open and that the TEST-OPERATION switch is in the OPERATION position.

In the WinSetup Work Space select the appropriate device, click the right mouse button and choose LPG Setup.

Step 2. Choose Air Correction.

In the LPG Setup window click the Correction button.

Choose Air Correction Only from the list of correction methods and click the OK button.

NOTEThe Air Correction Only option shall only be used when the tank atmosphere contains air and no other gases.

(When the LPG configuration is finished the correction method will be changed to a correction method that applies to the particular type of product that is used. See “Choose correction method.” on page 3-107).



Step 3. Choose Vapor Pressure and Vapor Temperature Source.

In the LPG Setup window click the Pressure button and choose Vapor Pressure Source.

As source signal you can choose one of the analog inputs or a HART slave device. It is also possible to set a manual value.

NOTE!Pressure is not required for correction method One or more known gases, known mixratio.

In the LPG Setup window, click the Temperature button and choose the desired temperature source.

There are a number of options available depending on the type of transmitter that is installed. For the Rex gauge you can choose one of the spot sensors connected to the transmitter, the average temperature for sensors above the liquid surface, an analog input signal or the input from a HART slave device.




Step 4. Calibrate.

Make sure that there is no liquid above the calibration ring (or bottom plug) at the end of the pipe. Check the Ullage value measured by the transmitter (Ullage = Tank Height R- Product Level L). If the Ullage value is not equal to the actual distance between the RTG Reference Point and the calibration ring, open the transmitter Properties window (right-click the device icon and choose Properties), choose the RTG Geometry tab and adjust the Calibration Distance (see “Step 6: RTG Geometry” on page 3-65).

Step 5. Configure the reference pins.

In the LPG Setup window click the Config Pins button.

Enter the reference pin positions. The position is measured from the RTG Reference Point (see “Step 5: Tank Distances” on page 3-63 ) to the actual position of the reference pin.

Since hand dipping can not be performed in high pressurized tanks, Emerson Process Management / Rosemount Tank Gauging has developed a unique method to verify level gauging in such tanks. The method is based on measurement in a special radar wave propagation mode against fixed reference pins. Up to three reference pins can be mounted in the pipe in order to verify the measurement.

NOTE!The value that you enter in the Nominal Pos field refers to the mechanical distance from the RTG reference point to the reference pin. This value will only act as a starting point for the following verification process in which the electrical distance from the RTG reference point to the reference pin is calculated. In most cases the electrical distance deviates from the actual mechanical distance.



Make sure that the Threshold value is 500 mV.

The amplitude of the echo from the Reference Pin must be above the threshold value in order to appear in the LPGVerify window (see Step 6 on page 3-106). If for some reason one of the Reference Pins does not show up, it is possible to use a smaller threshold value for that particular Reference Pin. Check that the product level is not above the reference pin.

NOTE!When the product surface is close to a reference pin, the radar echoes from the reference pin and the product surface interfere, and the measured distance to the reference pin becomes inaccurate. It is recommended that verification is not performed if the distance between a reference pin and the product surface is less than 900 mm.

RTG REFERENCE PIN

RTG REFERENCE POINT

Distance from RTG reference point to reference pin

MINIMUM CLEARANCE 900 MM

REFERENCE PIN




Step 6. Verify the gauge measurement.

1. Turn the Calibration Handle to the TEST position on the Radar Tank Gauge. It is only in this position that the Reference Pins produce “visible” radar echoes. Make sure that the pins appear in the LPG Setup window.

In the LPG Setup window click the Verify Pins button.

2. In the LPG Verify Pins window click the Start button to start the verification process.

3. When the verification is finished, the measured position appears in the Measured Position column.

4. Note the position of the reference pin in the Measured Position field. If the measured position deviates from the nominal position, return to the RTG LPG Configure Pins window and enter the measured position into the Nominal Position field.

NOTE!The nominal position that was entered the first time refers to the mechanical distance. The measured position refers to the electrical distance which is the distance “seen” by the RTG.

5. In the LPG Verify Pins window click the Start button again to start a new verification. Repeat steps 3 and 4 until the nominal position in the RTG LPG Configure Pins window is close to the measured position in the LPG Verify Pins window.

NOTE!Remember to put the Calibration Handle on the Radar Tank Gauge back to the OPERATION position after the verification procedure is finished.



Step 7. Choose correction method.

There are several options available depending on the number of products and product type. Click the Correction button:

Choose one of the following methods:

1. Air Correction.This method should only be used when there is no vapor in the tank, i.e. when the tank contains only air. This method may for example be used when the transmitter is calibrated.

2. One known gas.This method may be used when there is only one gas type in the tank. It provides the highest accuracy among the different correction methods. Note that even small amounts of another gas reduces the accuracy.

3. One or more unknown gases.Use this method for hydrocarbons, for example Propane/Buthane, when the exact mixture is not known.

4. Two gases, unknown mixratio.This method is suitable for a mixture of two gases even if the mixratio is not known.

5. One or more known gases. Known mixratioThis method may be used when there is a well known mixture of up to 4 products in the tank.




3.15 SETTING UP A HYBRID TANK MEASURING SYSTEMTankMaster Based Hybrid Calculations

This is a description of how to install an on-line density measurement system to be used for mass calculations. Before the setup is started make sure the FCU Slave Database is configured accordingly, see “Installing a Field Communication Unit (FCU)” on page 3-23.

For the mass calculations to work properly, a tank strapping table (also referred to as a Tank Capacity Table) must be entered, see TankMaster WinOpi User´s Guide for more information on strapping tables.

The description is based on an example with a TankRadar Rex gauge connected to two pressure transmitters:

• Liquid Pressure P1 is measured by a pressure transmitter connected as a HART slave to Analog Input 1 on the Rex gauge. Note that P1 does not have to be connected as a HART device. This option is only used as an example.

• Vapor Pressure P3 is measured by a second pressure transmitter which outputs a 4-20 mA signal to Analog Input 2 on the Rex gauge.

Step 1. System Setup

1. Start TankMaster Winsetup.

2. In TankMaster WinSetup select the tankserver icon. In this example the tankserver is located onThis Workstation. Click the right mouse button and select Setup,- or -select This Workstation and choose menu option Service>Servers>Setup.



3. Select the Units tab.

4. Choose the desired measurement units for Density and Pressure.5. Select the Inventory tab.

6. For Local Gravity choose calculation method Manual or Calculated. The Local Gravity is used for calculating the Observed Density. For Manual enter a local gravity value. For Calculated select the latitude and elevation of the site.

Pressure

Density




Step 2. Input configuration

Rex 3900 Hart Slave Device ConfigurationThis example shows how to configure the pressure sensor P1 connected as a HART slave device to the Analog Input 1 of the Rex gauge.

1. In WinSetup select the icon that represents the gauge to be configured.

2. Click the right mouse button and choose Properties,- or -choose Service>Devices>Properties.



3. Select the Configuration tab and click the Hart Devices button.

4. Enter a Description for the Hart Device and click the OK button. In the example the liquid pressure sensor P1 is connected to the Rex gauge as a HART slave device.

NOTE!The Hart device must be pre-configured.

Hart Devices




Rex 3900 Analog Input ConfigurationThis example shows how to configure the pressure sensor P3 connected to the Analog Input 2 of the Rex gauge.

1. In WinSetup select the icon that represents the gauge to be configured.

2. Click the right mouse button and choose Properties,- or -choose Service>Devices>Properties.



3. Select the Configuration tab and click the Analog Input 2 button.

4. Configure the Analog Input 2 for Liquid Pressure, and click the OK button.

Analog Input 2




Step 3. Configure Pressure Source

1. In Winsetup select the desired tank icon in the workspace window.

2. Click the right mouse button and choose Properties,- or -from the Service menu choose Tanks>Properties.

3. Select the Configuration tab.

4. Configure the sensors that measure Vapor Pressure and Liquid Pressure. In the example above the sensors are configured as follows:• Vapor Pressure P3 - Analog Input 2: AI[1]• Liquid Pressure P1 - HART device 1: HI[0]

HART Device 1

Analog Input 2



Step 4. Verify meausurements in the Tank View window

To confirm that data is measured properly, do the following:

1. In the WinSetup workspace window select the desired tank icon.

2. Click the right mouse button and choose Open Tank View,- or -from the Service menu choose Tanks>Open Tank View.

3. Verify that data is presented according to configuration.




Step 5. Tank Setup

Configure the Liquid Pressure and Vapor Pressure sensors:

1. In the WinSetup workspace window select the tank icon.

2. Click the right mouse button and choose Hybrid Tank Setup,- or -from the Service menu choose Tanks>Hybrid Tank Setup.

3. Enter the P1 Sensor Position, i.e. the position of the center of the Liquid Pressure sensor membrane.



4. Enter the Hybrid Min Level. This value specifies the lowest product level at which TankMaster calculates the Observed Density. Normally, the accuracy of pressure sensors is poor for low pressures, i.e. at product levels close to the sensor membrane. Therefore, you can enter a limit below which the density calculation is “frozen”. If you for example type 0.6 in the Hybrid Min Level field, WinOpi will present the same density value for product levels below 0.6 meter.

NOTE!Specify the actual product level and not the distance between the pressure sensor and the product surface.

5. Enter the P3 Sensor Position, i.e. the position of the center of the Vapor Pressure sensor membrane.

6. Click the OK button to save the Hybrid Tank Setup configuration.

Step 6. Tank Entry

1. In the WinSetup workspace window select the desired tank icon.

2. Click the right mouse button and choose Tank Entry,- or -from the Service menu choose Tanks>Tank Entry.




3. Make sure that the Reference Density is measured automatically, i.e. the check box is unchecked.

4. Open Properties for the selected tank (Service>Tanks>Properties) and select the Value Entry tab:

5. Make sure that Liquid Pressure and Vapor Pressure are measured automatically, i.e. Value Source is set to Automatic.

Reference Density is automatically measured

Check that Value Source is set to Automatic



Step 7. Tank Inventory

Check the result in the Tank Inventory window:

1. In the WinOpi workspace select the tank icon.2. From the View menu choose Tank>Tank Inventory.

If the calculations seem to be incorrect, see section Checklist for Inventory Parameter Setup in the TankMaster WinOpi Reference Manual for guidance.




3.16 CALIBRATION Normally a minor adjustment of the Calibration Distance is needed in order to achieve good agreement between measured and actual product level. A small offset can for example result from deviations between the actual tank height and the value stored in the gauge database, or from differences between various RTG microwave units and antennas.

You can choose to make a manual adjustment of the Calibration Distance, or you can use the Calibrate function to let WinSetup automatically calculate an optimized Calibration Distance based on measurement data from different product levels.

NOTE!The following is a brief description of how to calibrate a Rex gauge. For a comprehensive description, see the Rex Service manual.

3.16.1 Manual Adjustment

For Rex gauges a rough calibration can be made by manually adjusting the Calibration Distance parameter (for non-standard antennas the Tank Connection Length (TCL) may need to be adjusted ). By comparing a hand dipped level with the corresponding level measured by the gauge, a Calibration Distance value can be calculated according to the formula:

New Calibration Distance=Old Calibration Distance+DL,

where DL=observed level (hand dip) - gauge level reading.

To change the Calibration Distance stored in the gauge database:

1. Select the gauge icon in the WinSetup workspace.2. Click the right mouse-button and choose the Properties option.

3. Select the RTG Geometry tab.4. Type the Calibration Distance value in the corresponding input field and

click the OK button.

See the Rex Service manual for further information.

Calibration Distance



3.16.2 Using the Calibrate Function

The Calibrate function is a tool which allows you to calculate the Correction Factor for still-pipe measurements. It also optimizes measurement performance from the top of the tank to the bottom, by automatically minimizing the offset between actual product levels and corresponding values measured by the gauge.

To calibrate a Rosemount TankRadar REX gauge:

1. Select the desired gauge in the Workspace window, click the right mouse button and choose Calibrate,- or -choose Calibrate from the Service/Devices menu:

2. Click the Calibration Data button. In the Calibration Data window enter hand dipped level values and the corresponding levels measured by the gauge. Click the Save Calibration Data in PC Database button.

The Calibration window displays a straight line fitted through measurement points representing the difference between hand dipped level values and values measured by the RTG. For still-pipe antennas a sloping line is displayed, otherwise the line is horizontal.

3. Click the Write new calibration data to RTG button in order to save the current calibration data. By clicking the Write new calibration... button, a new Calibration Distance is calculated and the REX Level values in the Calibration Data window are recalculated.

See the TankRadar Rex Service manual for further information on calibrating a Rosemount TankRadar Rex radar level gauge.






Section 4 Device Handling

4.1 To Change Device Configuration . . . . . . . . . . . . . . page 4-14.2 To Uninstall a Device . . . . . . . . . . . . . . . . . . . . . . . . page 4-3

4.1 TO CHANGE DEVICE CONFIGURATION

Once you have installed and configured a device, you can modify the current settings at any time by opening the corresponding Properties dialog. To open the Properties dialog for a RTG do the following:

1. In the Workspace window select the device you want to configure.2. Click the right mouse button

- or -from the Service menu choose Devices.

3. Choose the Properties option.

Properties




Now the Properties window appears with a number of tabs allowing you to change the current device settings.

Basically the tabs correspond to the different steps in the installation wizard. Similar dialogs are available for other device types as well, for example FCUs and DAUs.

See Section 3: Installing a Level Gauging System for detailed descriptions on how to configure various device types.

4-2 Section 4. Device Handling


4.2 TO UNINSTALL A DEVICE

Once you have installed and configured a device, it can be uninstalled at any time. However, the associated tank must be uninstalled first, or if you want to keep the tank, you can disconnect the device from the associated tank.

To uninstall a device do the following:

1. Start by uninstalling the associated tank, see “To Uninstall a Tank” on page 3-43. Alternatively, if you want to keep the tank and only disconnect the device, use the method described in section “Uninstalling a device without uninstalling the tank” on page 4-3.

2. Select the desired device and click the right mouse button.3. Choose the Uninstall option.

Now the device is removed from the WinSetup workspace.

Uninstalling a device without uninstalling the tank

If you want to keep the tank, you can disconnect it from the device and then uninstall the device:

1. Select the desired tank and click the right mouse button.

2. Choose the Properties option and select the Configuration tab.

Uninstall

Properties

4-3Section 4. Device Handling



3. Click the Change button.

4. Select the device in the right pane and click the left arrow. Click the OK button.

Response: the tank is disconnected from the associated device.

Change

Left arrow



5. In the Devices folder in the WinSetup workspace, select the device and click the right mouse button.

6. Choose the Uninstall option.

Now the device is removed but the tank is still available in the WinSetup workspace.

The “+”-sign is removed indicating that the tank has no associated device.

4-5Section 4. Device Handling





Section 5 Protocol Handling

5.1 Channel Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . page 5-15.2 Logging the Channel Communication . . . . . . . . . . page 5-35.3 Saving the Communication Log to File . . . . . . . . . page 5-55.4 Searching for Connected Devices . . . . . . . . . . . . . page 5-8

5.1 CHANNEL STATISTICS

The Protocol Statistics function is a tool which can be used to check the quality of the communication between the TankMaster PC and the connected devices. To view statistical data for a protocol channel do the following:

1. Open the Protocols folder and the appropriate protocol sub folder.

2. Select the desired channel.

Protocols folder

Protocols sub folder

Statistics

Channel




3. Click the right mouse button and choose the Statistics option - or -from the Service menu choose Channels/Statistics.

The Channel Statistics window lets you view a summary of messages and various types of errors.

5-2 Section 5. Protocol Handling


5.2 LOGGING THE CHANNEL COMMUNICATION

To log the communication for a particular protocol channel do the following:

1. Select the protocol channel icon.

2. Click the right mouse button and choose the View Log option - or -from the Service menu choose Channels/View Log.

3. Specify a log profile. You can filter out certain function codes and devices as well as various error types:

Function Code A Function Code defines a specific action or type of data. You can log all function codes or a specific code.

Device Address You can log all devices or a specific device.Enable Filtering Mark this check box to enable filtering by

function codes and addresses.Type of error Select the check box that corresponds to the

type of error you like to record: Time-out, Check Sum or Other Errors. You can mark several check boxes if you like.

Number of messages Set the number of messages that will be added each time the Communication Log window is updated. If the log is updated too quickly, increase the Number of messages value to reduce the update speed.

View Log

5-3Section 5. Protocol Handling



4. Click the OK button to open the Communication Log window.

The Communication Log window is continuously updated with new values.

To stop WinSetup from feeding new values click the right mouse button and choose Freeze.

The Save As option lets you save the current log to file.

Choose the Log Setup option if you want to change the filtering settings.

Log Setup

Save As

Freeze

Clear



5.3 SAVING THE COMMUNICATION LOG TO FILETo save the communication log to file:

1. Select the protocol channel icon.

2. Click the right mouse button and choose Properties,- or -from the Service menu choose Channels/Properties.

3. Select the File Log tab.4. Type a name of the log file in the File Name field and set the Maximum

File Size. The Maximum File Size option is typically used in combination with the Multiple Log Files option, in order to store the log file on a number of diskettes

NOTE!The log file will be stored in the folder \Rosemount\Server\Log, e.g. C:\Program Files\Rosemount\Server\Log.

5. Choose the One File option if you prefer the log to be stored in a single file. Choose the Several Files option if you like to divide the log into a number of files (a new log file will be started each time the maximum file size is reached). If the Several Files option is chosen, also set the Max Log Files parameter to define the maximum number of log files to be created.

Properties




6. Set the Log Schedule.

Manual: select Manual and click the Start button to start logging. The logging will stop when the Stop button is pressed, or the Maximum File Size is reached.

Automatic Stop: set the Date and Time at which you want the logging to be stopped. Press the Start button to start the logging. The logging will stop when the set Date and Time is reached, the Stop button is pressed, or the Maximum File Size is reached.

7. Click the Advanced button to set the filtering options.

8. Select the Enable Filtering by Function Codes and Addresses check box if you want to restrict logging to a certain function code and/or a certain device address.



9. Choose the Selected Function Code option if you want to log a specific function.

10. Choose one of the device address options. Choose Selected Address if you want to log a certain device.

11. Specify what type of errors to be logged by selecting the corresponding check boxes. You can choose to log one or several error types.


FC2 Read InputsFC3 Read Holding RegistersFC4 Read Input RegistersFC6 Write Single RegisterFC8 DiagnosticsFC13 ProgramFC14 Poll program completeFC16 Write Multiple RegistersFC17 Report Slave IDFC65 Change address




5.4 SEARCHING FOR CONNECTED DEVICES

You can search for devices associated to a certain communication channel:

1. Open the Protocols folder and the appropriate protocol sub folder.2. Select the desired protocol channel. For more information on Protocol

Channels, see “Communication Protocol Setup” on page 3-4.

3. Click the right mouse button and choose the Find Devices option - or -from the Service menu choose Channels/Find Devices.

4. Type the desired values in the First and Last address input fields in order to restrict the search to a certain range of addresses (maximum range is 1-255).

5. Click the Start button

Now the TRL/2 bus is scanned for devices within the specified address range.

The search results is a list showing the name, type, address, unit id and application software version of each device that was found.

Find Devices



Section 6 Viewing Tank Data

6.1 Viewing Data from All Tanks . . . . . . . . . . . . . . . . . . page 6-16.2 Viewing Data From a Single Tank . . . . . . . . . . . . . . page 6-26.3 Tank Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 6-36.4 Tank Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 6-4

WinSetup offers the option to view data from a single tank or a group of tanks. Various parameters such as Level, Level Rate, and Average Temperature can be displayed. Other parameters can be displayed as well as specified in the Setup Tank View window. See “Tank View Layout” on page 3-19 for more information.

6.1 VIEWING DATA FROM ALL TANKS

1. Select the Tanks folder.

2. Click the right mouse button and choose Summary Tank View, or from the Service menu choose Tanks/Summary Tank View.

3. Choose the All Tanks tab or the tab for a specific tank.




6.2 VIEWING DATA FROM A SINGLE TANK

1. Select the desired tank icon.

2. Click the right mouse button and choose the Open Tank View option- or -from the Service menu choose Tanks/Open Tank View:

The Tank View window shows measurement data for the selected tank.

Open Tank View

6-2 Section 6. Viewing Tank Data


6.3 TANK CAPACITY The tank geometry is defined in a strapping table; the Tank Capacity Table (TCT). The TCT is used to convert a product level to the corresponding volume. The values can be entered in different ways; as pairs of level and volume, as absolute levels or as relative levels.

To open the Tank Capacity Setup window for a certain tank, select the tank icon in the workspace window, click the right mouse button and choose the Tank Capacity option:

See the TankMaster WinOpi Reference Manual for more information on the Tank Capacity Setup window.

6-3Section 6. Viewing Tank Data



6.4 TANK ENTRY The Tank Entry window is used for specifying a number of product parameters to be used for inventory calculations. TankMaster can use measured data, or data that is manually entered. To open the Tank Entry window:

1. In the WinSetup workspace select the tank to configure.2. Choose Service>Tanks>Tank Entry:

3. To enter manual values select the check box and type the desired value in the corresponding input field. Manual values are marked with yellow color.

See the WinOpi Reference Manual for further information on how to use the Tank Entry window.

6-4 Section 6. Viewing Tank Data


Section 7 Viewing Alarm Status
WinSetup offers the option to view alarm status for a single tank or for a tank group. To view the alarm status do the following:
1. To view the alarm status of all tanks select the work station (or the Tanks folder) where the tanks are installed:

To view the alarm status of a single tank open the Tanks folder and select the desired tank:

Workstation

Single tank




2. From the View menu choose Alarms.The Alarm Status window presents a list of various parameters for a tank group or a single tank, depending on which icon that was selected in the Workspace window. This function allows you to check that communication is established and that measurement values are properly delivered from the gauges.

Alarm status for a tank group:

Alarm status for one tank:

7-2 Section 7. Viewing Alarm Status


Section 8 Service Functions

8.1 Manual Relay Control . . . . . . . . . . . . . . . . . . . . . . . . page 8-28.2 HART Device Status . . . . . . . . . . . . . . . . . . . . . . . . . page 8-38.3 User Defined Temperature Conversion . . . . . . . . . page 8-48.4 Viewing Input and Holding Registers . . . . . . . . . . . page 8-68.5 To Edit Holding Registers . . . . . . . . . . . . . . . . . . . . page 8-78.6 Saving and Loading Database Registers . . . . . . . . page 8-88.7 Uploading new Gauge Software . . . . . . . . . . . . . . . page 8-118.8 System Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 8-128.9 Tank Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 8-138.10 View Diagnostic Registers . . . . . . . . . . . . . . . . . . . . page 8-258.11 Overview IOT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 8-278.12 Customizing the Tools Menu . . . . . . . . . . . . . . . . . . page 8-29




8.1 MANUAL RELAY CONTROL

To manually switch between different relay states do the following:

1. Select a Rex gauge icon in the WinSetup workspace.

2. Click the right mouse button and choose the Manual Control Relay option- or -from the Service menu choose Devices/Manual Control Relay.

3. Make sure that an appropriate Safety Reset value is set. This value specifies the time-out period for the relay to reset if a communication failure occurs.

4. Choose Manual in the Control Mode pane.5. Choose a new relay state from the Select New State list.

Manual Control Relay

8-2 Section 8. Service Functions


8.2 HART DEVICE STATUS

To view the status of connected HART devices:


2. Click the right mouse button and choose the HART Device Status option.

3. View the desired HART device by selecting the appropriate tab.

HART Device Status

8-3Section 8. Service Functions



8.3 USER DEFINED TEMPERATURE CONVERSION

8.3.1 Using a Linearization Table

When using a resistance temperature sensor, the resistance values can be converted to temperature values by using a table of resistance and corresponding temperature values.

To create a conversion table:

1. Select a Rex gauge in the Workspace window.2. Click the right mouse button and choose the User Defined

Linearization Table option:

3. Specify the number of conversion points in the Length of Table input field.

Response: A table is created with the specified number of rows.

4. Type resistance values into the first column (Ohm) and the corresponding temperatures values in the second column (°C).

5. Click the OK button to store the table.

To enable the linearization table for temperature conversion:

1. Select the icon in the Workspace window that corresponds to the Rex gauge in question.

2. Click the right mouse button and choose the Properties option.3. Select the Configuration tab and click the Temp Input button (see “Step

4: RTG Configuration” on page 3-51).4. In the Sensor Type list choose Spot User Defined Table or Average

User Defined Table depending on the type of sensor that is used.



8.3.2 Using a Mathematical Formula

When using a resistance temperature sensor, the resistance values can be converted to temperature values by using a mathematical formula:

R=R0*(1+A*T+B*T2)

where R is the resistance at temperature T, R0 is the resistance at zero degrees Celsius, and A and B are constants.

To create a conversion formula:

1. Select a Rex gauge in the Workspace window.2. Click the right mouse button and choose the User Defined Formula

option.

3. Enter the parameters R0, A and B in the corresponding input fields. R0, A and B are stored in the gauge.

4. Click the OK button to store the formula.

To enable the formula for temperature conversion:

1. Select the icon in the Workspace window that corresponds to the Rex gauge in question.

2. Click the right mouse button and choose the Properties option.3. Select the Configuration tab and click the Temperature button (see

“Step 4: RTG Configuration” on page 3-51).4. Choose Spot User Defined Formula in the Sensor Type list.




8.4 VIEWING INPUT AND HOLDING REGISTERS

Measured data is continuously stored in the Input registers of DAUs, RTGs and FCUs. By viewing the contents of device input registers you can check that the device is working properly.

The Holding registers store various transmitter parameters used to control the measurement performance.

To view input or holding registers of a certain device do the following:

1. Select the device in the Workspace window.2. Click the right mouse button and choose the

View Input/Holding Registers option,- or -from the Service menu choose Devices/View Input/Holding Registers.

3. Choose Predefined if you want to see a basic selection of registers. Choose the All option to view a range of registers by your own choice.

For the All option, specify a range of registers by setting a start value in the Start Register input field, and the total number of registers to be displayed in the Number of Registers field (1-500).

4. Click the Read button.



8.5 TO EDIT HOLDING REGISTERS

Most Holding registers can be edited simply by typing a new value in the appropriate Value input field. Some holding registers (marked grey in the Value column) can be edited in a separate window. In this case you can choose from a list of options or you can change separate data bits.

To edit a holding register do the following:

1. Select the device in the Workspace window.2. Click the right mouse button and choose the View Holding Registers

option- or -from the Service menu choose Devices/View Holding Registers.

3. In the Value column, put the cursor in the field that corresponds to the register you want to edit.

4. Type a new value.

Some registers are marked grey in the Value column. To edit these registers do the following:

1. Double click in the Value input field.

Response: Depending on the type of Holding register, an Expanded Enumerated or an Expanded Bitfield window is opened(1).

2. Select from the list of options (Expanded Enumerated) or change the appropriate data bit (Expanded Bitfield).

(1) Contact Emerson Process Management/Rosemount Tank Gauging for more information about the different Holding register types.




8.6 SAVING AND LOADING DATABASE REGISTERS

8.6.1 To Save Device Registers

Single Device

To save registers to file for a single device do the following:

1. Select the device in the Workspace window.2. From the Service menu choose Devices/Save Database to File

- or - click the right mouse button and choose the Devices/Save Database to File option.

3. Choose the type of registers to save, Input or Holding registers.4. Choose range; Predefined or User-Defined.

The Predefined option lets you store the registers which are most frequently used. The User-defined option lets you specify a certain range of Holding registers or Input registers.

5. For the User-defined option specify a range of registers by entering the the first and last register.

6. Click the Browse button, select a folder, and type a file name.7. Click the OK button to save the register data.



Multiple Devices

To save database registers to file for multiple devices do the following:

1. Select the Devices folder in the Workspace window.2. Click the right mouse button and choose the Devices/Save Database of

All to Files option - or - from the Service menu choose Devices/Save Database of All to Files.

3. Select a device from the Available Devices pane and click the Add button. Repeat for all devices you wish to include.

4. Choose Predefined or User-defined. The Predefined option lets you store the registers which are most frequently used store the most used registers. The User-defined option lets you specify a certain range of holding registers to be saved.

5. For the User-defined option specify a range of registers by entering the first and last register.

6. Click the Browse button and select a folder and a file name.7. Click the OK button to save the register data.




8.6.2 To Load a Device Database

Rosemount TankRadar Rex gauges are equipped with databases that contain parameters used for the Application Software (see the TankRadar Rex Service Manual) to control the performance of the gauge. TankMaster WinSetup offers the option to load a new database to replace the current one. This can be useful if, for example, you want to try out new database settings and then reload the original database.

To load a database do the following:

1. Select the particular device in the Workspace window for which you want to load a new database.

2. From the Service menu choose Devices/Upload Database.- or - click the right mouse button and choose the Devices/Upload Database option.

3. Type a file path and file name, or click the Browse button and choose a database file to be uploaded.


Response: the selected database is downloaded to the gauge.



8.7 UPLOADING NEW GAUGE SOFTWARE

WinSetup includes the option to reprogram gauges with new application and boot software (see the Rex Service Manual for more information on gauge software).

To upload a new program do the following:

1. Select the Devices folder in the Workspace window or a single device in the Devices folder.

2. Click the right mouse button and choose the Program All option, or for a single device, choose the Program option.

3. Select the device to be programmed from the Available Devices pane and click the Move button. Repeat for each device to be programmed.If a single device was selected in the Workspace window, no device will appear in the Available Devices pane of the Program Devices window. The selected device appears automatically in the Program These Devices pane.Use the Remove button if you want to change the list of devices to be programmed.

4. Click the Browse button to locate the flash program file, and click the Start Programming button.

Response: the Start Device Programming window appears.

5. Make sure the devices are properly prepared for reprogramming and click the Start Programming button to activate device programming.

Response: the programming process starts.

See the TankRadar Rex Service Manual for further information on programming a TankRadar REX gauge.




8.8 SYSTEM STATUS The System Status Overview shows status and properties for the overall system, Tank Server, Protocol Servers, and devices.

To open the System Status Overview do the following:

1. Select a workstation in the Workspace window.2. From the Service menu choose Servers/System Status Overview.



8.9 TANK SCAN The Tank Scan window allows you to view tank echoes and setup the most important parameters to enable the gauge to distinguish between the surface echo and disturbing echoes and noise. It is currently available for TankRadar Pro and Rex level gauges.

To open the Tank Scan window:


2. Right-click the device and choose Properties in the popup menu.

Response: the REX RTG Properties window appears.




3. Select the Configuration tab and press the Tank Scan button.

4. The Tank Scan window contains the Graph Area, Legend/Options area, File Storage buttons, and various action buttons.

Tank Scan



8.9.1 Graph Area When the Tank Scan window is opened, the system starts reading tank data from the gauge (indicated by a progress bar in the lower right corner of the window).

After a while the graph area presents data downloaded from the gauge.

The Tank Echo curve shows the measurement signal in graphical form. It may contain one or several peaks. Apart from the surface echo there might be echoes from agitators or other obtacles in the tank. In the graph area you can configure the gauge so that it will always correctly recognize which echo peak that corresponds to the product surface. See the following chapters for details.

The tank echo and echo peaks can be refreshed at any time with the Reread From Gauge button. The new echo curve will be shown as a black line and the previous curve as a grey line. The graph may show up to two old echo curves. An old echo peak will be marked by a small cross. This can be used to compare the existing tank signal with previous signals.

Progress barReread From Gauge




8.9.2 Legend/Options The following items can be shown in the graph area (check the appropriate box for each item to be shown):

Tank Echo The black line shows the latest Tank Echo curve, and the grey lines show previous Tank Echo curves (maximum two).

Prev. Tank Echo(Previous Tank Echo)

See Tank Echo.

General Threshold The General Amplitude Threshold is shown in blue. Echoes with an amplitude below the General Amplitude Threshold will bedisregarded.

False Echo Areas The False Echo function is used to improve the performance of the gauge when the surface is close to a horizontal surface of a stationary object in the tank. The object causes an echo when it is above the surface. Added False Echo Areas are shown in grey:

Previous Tank Echo curve

Tank Echo curve



ATP (Amplitude Threshold Points)

A weak disturbing echo can be filtered out by creating a curve of Amplitude Threshold Points.

Holdoff Distance The Holdoff Distance defines how close to the Gauge Reference Point a level value is accepted. The Holdoff Distance is shown in red.

Gauge Ref. Point (Gauge Reference Point)

The Gauge Reference Point is shown as a dashed (olive colored) line:

Zero Reference The Zero Reference (zero level; dipping datum point) close to the bottom of the tank, is defined by the Tank Reference Height (R). It is shown as a dashed (sand colored) line:

Amplitude Threshold Point

Disturbing Echo




Tank Bottom The Tank Bottom is shown in red:

Echo Peaks Echo Peaks are shown in black for the Surface Echo and in green for unknown echoes:

Peak Labels Peak Labels are shown for the Surface Echo and for unknown echoes:

Previous Peaks Previous Peaks are shown for the Surface Echo and for unknown echoes:

Previous Peaks



8.9.3 File Storage To save Tank Scan data displayed in the Graph Area

1. In the Tank Scan window click the Save button.

2. Enter a name to identify the tank scan data. You may also type a comment in the Comment field (not required). This can for example be used to describe any special circumstances under which the Tank scan data was obtained.

3. Press the OK button.

NOTE!The default data storage file is named StrTankScanII.dat. The file is stored in the following folder: C:\Program Files\Rosemount\Lib\Data\.

To export Tank Scan data to an external file

1. In the Tank Scan window click the Save button.

2. Enter a name to identify the tank scan data. You may also type a comment to describe any special circumstances when the Tank scan data was obtained.

3. Press the Advanced button.

4. Check the Export tank scan data to external file check box. 5. Press the Browse button.




6. Browse to a destination folder and type a name in the File name input field. Press the Open button

7. Press Yes to create the file.

8. Press OK.

9. Press OK to export the tank scan data.



To load data from a saved file into the Graph Area

1. In the Tank Scan window press the Stored Echoes button.

2. Select the file to be loaded to the Tank Scan window.3. Press the Load button.

To delete a saved file

1. In the Tank Scan window press the Stored Echoes button.

2. Select the file you want to delete.3. Press the Delete button.




8.9.4 Action Buttons The following buttons can be found in the Tank Scan window:

Save See “File Storage” on page 8-19.

Stored Echoes

See “File Storage” on page 8-19.

Reread From Gauge

At any time, you can reread tank echo and echo peaks with the Reread From Gauge button. The new echo curve will be shown as a black line and the previous one will change its color to grey. You can show up to two old echo curves. Also, previous echo peaks will change their appearance and will be shown as small crosses.

Print Opens the print dialogue and prints the Tank Scan window.

Apply If you have changed the settings for a parameter that affects echo peak detection (e.g. General Amplitude Threshold), you will have to press the Apply button to write these settings to the gauge. It will take a few seconds for the gauge to update the echo peak data (about 30 seconds due to the echo peak filtering function in the gauge).

Finally, press the Reread from Gauge button to update the echo peak information in the graph area.

OK Applies changes and closes the window.

Cancel Cancels all changes.

Help Opens the online help for the window.



8.9.5 Editing All the elements having handles are editable. Each handle may be moved by using the mouse pointer.

Clicking the right mouse button on a handle opens a dialog window. The Properties option allows you to review or change parameter values.

The following parameters can be edited via moving or right-clicking a handle:• General Amplitude Threshold• Amplitude Threshold Point• False Echo Area• Hold Off Distance

Handles for moving or right-click editing

Properties




To add a False Echo Area or an Amplitude Threshold Point

1. Right-click in the graph area where you want to add a False Echo Area or an Amplitude Threshold Point.

2. Select a menu item in the popup menu. In the example the New False Echo Area option was chosen.

3. Click OK.

To delete a False Echo Area or Amplitude Threshold Point:

1. Right-click the handle for the False Echo Area or Amplitude Threshold Point to be deleted.

2. Select the Delete False Echo Area (or Delete Amplitude Threshold Point) option.



8.10 VIEW DIAGNOSTIC REGISTERS

The View Diagnostic Registers window shows a predefined set of diagnostic input and holding registers. For each device (RTG, DAU, FCU, Pro, and Rex) there is a default set of diagnostic registers which can be changed in the Configure Diagnostic Registers window (see below). Clicking the right mouse button on a handle opens a dialog window. The Properties option allows you to review or change parameter values.

To view and configure the diagnostic registers:


2. Click the right mouse button and choose View Diagnostic Registers.

The register values in this window are read only. They are read from the device when the window is opened.

A grey background color of the table cell in the Value column means that the register is of either Bitfield or ENUM type. An expanded Bitfield/ENUM window can be opened for that type of registers. Double-click the cell to open the Expanded Bitfield/ENUM window.

If needed, the values can be presented as hexadecimal numbers. This applies to registers of the Bitfield and ENUM types. Select the Show in Hex check box to present Bitfield and ENUM registers as hexadecimal numbers.




It is possible to view diagnostic registers for devices of the same type without closing the window and opening it again for a new device. Press or

buttons to step to the next or previous device of the same type. Alternatively, another device can be selected from the pull down menu to the left of these buttons.

Press the Print button to print the register information.

Press the Configure button to bring up the Configure Diagnostic Registers window.

3. In this window you can change the default set of diagnostic registers for the given device type.

You can choose between Holding and Input registers in the Registers Type pull down menu. Input Registers are displayed in blue, Holding Registers in black.

The list is filtered using the Group Prefix pull down menu. Use this menu to select which registers to show in the left pane.A default set of registers is displayed in the right pane.

To add a register to the Selected Registers pane on the right-hand side, select it in the left pane and press the button.

To remove a register, select it in the Selected Registers pane on the right-hand side and press the button.

Select a register in the right pane and press to move it upwards, or to move it downwards in the list.

NOTE!Some devices do not support the Group Prefix feature. For example, Group Prefix is not available for TRL/2 gauges.

4. Press OK when the configuration is done.

Registers Type

Group Prefix



8.11 OVERVIEW IOT The I/O Terminal Overview window shows information about the I/O terminal devices (IOTs). The information consists of analog inputs, analog outputs, digital inputs, digital outputs, and status information.

To open the I/O Terminal Overview window:

1. In the WinSetup workspace select the Devices folder.

2. Click the right mouse button and select the Overview IO Terminals menu item.

3. In the I/O Terminal Overview window all terminal devices are grouped according to device type, i.e. 5110, 5120, 5130, and 5140.

In this window you can find the following information:

• Analog inputs for IOT 5110, analog outputs for IOT 5120, digital inputs for IOT 5130, and digital outputs for IOT 5140.

• If the channel is enabled or disabled. An enabled channel has a white background and a disabled channel a light gray background with no value showing.

• Device status.• Communication port and address.

All table cells are of type “Read Only”.

Select Raw or Scaled values




The channel data can be shown as either Raw Values or Scaled Values. This setting is done in the Show pane. Only raw value (0 or 1) can be shown for the Digital terminals. On how to set the various properties for IOTs, see “Installing an IOT” on page 3-86.

To print a report:

1. Click the Print button.

2. Select Window image to print a screen dump of the actual window, or select Table data to print the contents of the window presented as a table.

3. Press OK and choose printer and printer settings. Press OK again to start printing.

4. Click the Close button to close the I/O Terminal Overview window.



8.12 CUSTOMIZING THE TOOLS MENU

To add custom options to the Tools menu do the following:

1. Choose the Tools>Applications menu option.

Response: the Customize window appears.

2. Click the Add button to add a new menu option to the Tools menu.

3. In the Menu Text field type the text you want to appear in the Tools menu.

Add

Menu Text




4. Press the button next to the Command field.

5. Browse to the program file that will be associated with the new Tools menu option as given in the Menu Text field.

6. Click the Open button and return to the Customize window.7. In the Arguments field type any argument that you want to add to the

command line. This line is usually left blank.

NOTE!The Initial Directory field is not used.

8. Click the OK button.9. Choose the new menu option in the Tools menu and verify that the

associated application starts as expected.

Command

Browse button



Section 9 TankMaster Administrator

9.1 Log on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 9-29.2 Autostart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 9-49.3 Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 9-59.4 File Version Information . . . . . . . . . . . . . . . . . . . . . . page 9-119.5 Processes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 9-12

The TankMaster Administrator program provides the option to select which TankMaster programs that will start automatically when the PC is turned on. It also allows you to check which TankMaster processes that are currently running.

By using the backup option, copies of the current WinOpi, WinSetup and Tank Server configurations can be stored. In the event of a PC operating system crash, resulting in corrupt TankMaster files, these backup files can be used to restore the TankMaster settings and the registry of the Windows XP operating system.

To open the TankMaster Administrator, click the icon on the right-hand side of the MS Windows Taskbar:

Administrator icon




9.1 LOG ON To be able to make any changes in the TankMaster Administrator window you need to use the Log on function.

To log on to the TankMaster Administrator do the following:

1. Open the TankMaster Administrator window by clicking the Administrator icon on the right-hand side of the MS Windows Taskbar.

2. Press the Log on button.

3. Enter the password and press OK.

NOTE!The default password is admin.

Log on

9-2 Section 9. TankMaster Administrator


9.1.1 Changing the Administrator Program passwordTo change the TankMaster Administrator password, do the following:

1. Open the TankMaster Administrator window.

2. Log on to the Administrator.3. Click the Change Password button.4. Enter the old and the new passwords. Confirm the new password.

5. Press OK.

Change Password

9-3Section 9. TankMaster Administrator



9.2 AUTOSTART The Autostart function lets you specify programs to start automatically when the TankMaster computer is started.

To configure the Autostart option:

1. Open the TankMaster Administrator window.

2. Select the check boxes for the programs you want to start automatically. 3. The Autostart function is activated next time the TankMaster PC is

started.

Selected Autostart options



9.3 BACKUP The backup function can be used to save configuration data for devices and tanks as well as workspace settings for WinSetup and WinOpi.

To make backup copies of the current configuration do the following:

1. Open the TankMaster Administrator window and click the Backup button.

The Backup window contains the following:• Information on when the Last Backup and Last Auto Backup were

performed• Backup data files to create• File path to use for the backup files• Auto Backup settings

2. Select which data files to create in the Backup data files pane.• The TankServer option lets you backup tank and device configurations

(the Tank server must be running).• The Batch Server option lets you backup the batch database files (the

Batch server must be running). Note that the Batch server automatically removes a batch from the database after a certain number of days, see the TankMaster Batch Handling Reference Manual for more information.

• The Historical Data option lets you backup any previously created Historical Data, see the WinOpi User´s Guide for more information.

• The WinOpi and WinSetup options allows you to save the workspace configuration such as groups, colors, network settings etc.

• The Registry keys for TankMaster option lets you save the TankMaster settings of the MS Windows registry.

3. Choose the destination folder by pressing the Browse button.

Browse button




4. Choose the desired file destination. TankMaster automatically creates subdirectories for WinOpi, WinSetup, and Tankserver files.

5. Click the OK button to close the Browse for Folder window and return to the Backup window.

6. In the Auto Backup pane, select the Enable check box to enable automatic backup. Also set Start time and Interval (1-30 days). This will automatically backup the selected backup data files at the specified start time and interval.

7. Click the Save Configuration button to save the current Backup window settings.

8. Click the Backup Now button if you like to make a manual backup of the selected items in the Backup data files pane.




9.3.1 Restore If the PC operating system has crashed resulting in corrupt TankMaster files, the TankMaster settings can be restored by using the backup files. To restore the TankMaster configuration and data files do the following:

1. Check that WinSetup and WinOpi are closed. You may click the Processes button in the TM Administrator program to check if any TankMaster programs are running. Note that the TankMaster Administrator program itself also appears in the Processes window, see “Processes” on page 9-12. (You may also open the Windows Task Manager to make sure that the Tankserver.exe program is closed).

2. Open the TankMaster Administrator window.3. Click the Backup button. The Backup window appears.

4. In the Backup window click the Restore button.




5. The Restore Backup Wizard lets you restore tank and device configuration, BatchServer data and Historical data. You may also restore WinOpi and WinSetup configurations such as groups, color, network settings etc.

6. Click the Next button and follow the instructions. You will now be guided through a step-by-step instruction that lets you specify the folder where backup files are stored, and the type of data to be restored. You may also create a backup of the current configuration.

7. When the backup source folder is selected, you will be prompted to specify the data to be restored:

NOTEDo not select the Registry key option if upgrading from TankMaster version 4.H0 or older to version 4.H1 or newer. The Registry key option must not be used if TankMaster has been re-installed on another hard disk drive, or in another directory than the original installation. The file paths to the TankMaster configuration and data files must be the same for the backup files and the restored files.

8. The following options will also need to be specified:



9. The first option, Create a backup of the current configuration, should not be used if the restore function is used to replace corrupt configuration files. The Delete old configuration files option clears all configuration files which are not replaced by the Restore function. If this option is used it may be a good idea to backup the current configuration files in case you need to recover the current TankMaster configuration at a later point of time.

10. Click Next and review the restore settings:

11. Click Next to start the restore function:




12. The Copy Log button can be used to store the restore log in the ...Rosemount\Server\Log directory. Click the Next button to continue.

13. Check that no errors occured during the restore process and click the Finish button to close the restore wizard. In case an error occured you may click the Back button to find the error in the restore log.

14. Open the server data backup folder (in the current example: M:\TM_BAK\TM Backup xxx\Server\Data) and copy the contents.

15. Open the C:\Program Files\Rosemount\Server\Databackup folder (C:\Program Files is the folder where TankMaster is installed) and paste the copied files.

16. Restart WinSetup and WinOpi to check that all settings are restored.



9.4 FILE VERSION INFORMATION

The File Info option allows you to view a list of all the files included in the TankMaster software package. The list presents file versions and brief descriptions.

The list can be stored by using the Save to File button. The file is stored in text format which can be opened by any word processing program:

NOTE!When entering the filename in the Save to File dialogue, also enter filetype txt, e.g. enter File_Version.txt.




9.5 PROCESSES To view the running TankMaster programs, click the Processes button in the TankMaster Administrator window:

The Shutdown TM button lets you close all TankMaster programs except the TankMaster Administrator. In case a TankMaster client requests data, the TankServer starts up again.

By using the Shutdown TM and Staydown button the TankServer stays down regardless of any requests.

If the Also shutdown administrator check box is selected, the TM Administrator program is shut down as well.

Click the Update button to update the contents of the Processes window.



Section 10 Menu Items

10.1 File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 10-210.2 View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 10-210.3 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 10-310.4 Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 10-610.5 Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 10-6




10.1 FILE

10.2 VIEW

New Connection Connect to another tank server.

Install New

Tank Install new tanks by starting the tank installation wizard.

Device Install new devices by starting the device installation wizard.

Log On Log on as Administrator, Supervisor or Operator.

Log Off Log off from TankMaster to View Only mode.

Exit Exits the WinSetup program.

Toolbar Hide or reveal the Toolbar.

Status bar Hide or reveal the Status bar.

Find Object Search for a certain tank or device.

Workspace Open or close the Workspace window.

Refresh Views Updates the current view.

Alarms View a list of current alarms related to the selected tank. If you select the Tanks folder alarms for all tanks are displayed.

10-2 Section 10. Menu Items


10.3 SERVICEServers

Rename Change the server name.

Disconnect Disconnect from the current server.

Configure Digital Alarms Configure the system’s digital alarms, e.g. used for IOTs.

System Status Overview Opens an overview of installed devices, protocol servers, and more.

Setup Choose measurement units, ambient air source, and other system parameters.

Tanks

Install New Install a new tank.

Summary Tank View View various tank related variables like level, level rate, average temperature etc. for all installed tanks.

Approved Tanks (option) Shows a list of tanks approved for custody transfer.

Uninstall Remove a tank.

Rename Change a tank name.

Open Tank View View various tank related variables like level, level rate, average temperature etc. for a single tank.

Tank Entry View tank data in the Tank Entry window.

Hybrid Tank Setup Define pressure sensor positions for hybrid tank gauging.

Tank Capacity Set various tank parameters including TCT table.

Tank Volume Calculation Define settings for the tank volume calculation.

Calibrate Use the built-in calibration function to adjust the Tank Connection Length (TCL).

Properties View and change tank configuration parameters.

10-3Section 10. Menu Items



Devices

Install New Install new devices by starting the device installation wizard.

Program All Download an application program to a group of devices.

Save Databases of All to Files

This function lets you save the database registers for several devices.

Overview IOT Terminals View an overview of installed IOT terminals.

Uninstall Remove a device.

Save Database to File This function can be useful if you want to save the current database as a backup. It can be downloaded to a device by choosing the Upload Database option.

Upload Database Upload a database to a device.

View Input Registers View input register values. You can choose between a predefined set of registers or you can specify a certain range of registers.

View Holding Registers View holding (database) register values. You can choose between a predefined set of registers or you can specify a certain range of registers.

View Diagnostic Registers View the diagnostic registers for the selected device.

Restart Restart a device. The boot software performs an initialization procedure and memory tests are performed.

Program Download an application program to a device.

Calibrate Use the built-in calibration function to adjust the Tank Connection Length (TCL).

Manual Control Relay Manually change relay status.

HART Devices Status View the status of installed HART devices.

User Defined Linearization Table

Define a linearization table of resistance and temperature values.

User Defined Formula Define a mathematical formula for the resistance temperature sensor.

LPG Setup Configure an LPG tank.

LPG Verify Reference Pins

Hybrid Setup Configure the tank for hybrid calculations.



Custody Transfer Config (Option)

Shows the configuration information for the specified custody transfer.

Enraf Emulation Specify parameters needed for Enraf emulation.

Properties View and change the current device settings (not in View Only mode).

Protocols

Disable Disables the selected protocol.

Properties Opens the Protocol Properties window allowing you to choose a communication channel.

Configure Connect to the various protocol servers.

Channels

Find Devices Search for devices within a certain address range.

View Log View the Realtime Log window. You can choose to view only certain function codes, device addresses and error types.

Statistics Opens the Channel Statistics window displaying various statistical data like Messages received, Messages sent, Timeout errors etc.

State Displays information about the selected protocol channels.

Properties View and change the communication, file log and tank mapping (for slave protocols) settings (not in View Only mode).

Preferences Specify Tag prefixes and Tank View layout.

10-5Section 10. Menu Items



10.4 TOOLS

10.5 HELP

Applications Customize the Tools menu.

Administrative Tools

User Manager Manage the user accounts.

User Information Displays information about the current user.

Set Password Change the password for the current user.

Set Inactivity Timeout Define the user inactivity timeout.

Set Required Access Levels

Set the required access levels for various TankMaster operations.

Tank Echo Viewer Displays the tank scan viewer for the selected gauge.

Custom menu User defined menu item.

Reference Manual Opens the online help.

User Guide Opens the WinSetup User´s Guide with the Acrobat Reader program.

Set User Guide Set which User Guide (language) to open with the User Guide menu item.

About Setup Displays information about the WinSetup program.



Index
AAccess Levels . . . . . . . . . . . . . . 2-13Acrobat Reader . . . . . . . . . . . . . 1-5Add a new user . . . . . . . . . . . . . 2-11Administrator . . . . . . . . . . . . . . 2-10
Password . . . . . . . . . . . . . . . 9-3Shutdown Check Box . . . . 9-12

Air Correction . . . . . . . . . . . . . 3-102Alarm mode . . . . . . . . . . 3-57, 3-79Ambient Air Density . . . . . . . . . 3-16Ambient Air Temperature . . . . . 3-15Analog Input Configuration

Description . . . . . . . . . . . . 3-56Error Limits . . . . . . . . . . . . 3-56Filter Factor . . . . . . . . . . . . 3-56Value Range . . . . . . . . . . . 3-56Value Unit . . . . . . . . . . . . . 3-56

Analog input configurationREX . . . . . . . . . . . . . . . . . . 3-56

Analog Out Source . . . . . 3-57, 3-79Analog Output Configuration

Alarm Mode . . . . . . . . . . . . 3-79Analog Out Source . . . . . . 3-79Pro . . . . . . . . . . . . . . . . . . . 3-79Range Value . . . . . . . . . . . 3-79

Analog output configurationAlarm mode . . . . . . . . . . . . 3-57Analog Out Source . . . . . . 3-57Range Value . . . . . . . . . . . 3-57REX . . . . . . . . . . . . . . . . . . 3-57

Antenna typeuser defined . . . . . . . 3-52, 3-76

Automatic Stop . . . . . . . . . . . . . . 5-6Average Exclude check box . . . 3-67Average Temperature . . . 3-54, 3-78

BBackup . . . . . . . . . . . . . . . . . . . . 9-5Baud rate . . . . . . . . . . 3-4, 3-6, 3-9Binary High . . . . . . . . . . . 3-57, 3-79Binary Low . . . . . . . . . . . 3-57, 3-79

CCalibration . . . . . . . . . . . . . . . . . 3-3Calibration Data . . . . . . . . . . . 3-121Calibration Distance 3-65, 3-82, 3-120Calibration Handle . . . . . . . . . 3-106

C-distance . . . . . . . . . . . . 3-63, 3-80Channel statistics . . . . . . . . 5-1, 5-2CIU

Egpudev.ini . . . . . . . . . . . . 3-94CIU 858 compatible . . . . . . . . . 3-91CIU Prime . . . . . . . . . . . . . . . . . 3-91COM Port . . . . . . . . . . . . . . . . . . 3-4Communication Log . . . . . . . . . . 5-4Communication log

advanced button . . . . . . . . . 5-6device address . . . . . . . . . . . 5-3enable filtering . . . . . . . . . . . 5-3error type . . . . . . . . . . . . . . . 5-3filtering options . . . . . . . . . . . 5-6function code . . . . . . . . . . . . 5-3number of messages . . . . . . 5-3

Communication protocol parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2Communication Protocol Setup . 3-2Config Pins . . . . . . . . . . . . . . . 3-104Configure protocol server . . . . . 3-13Configure reference pins . . . . . 3-104Control Mode . . . . . . . . . . . . . . 3-59Correction Factor . . . . . . . . . . 3-121Customizing . . . . . . . . . . . . . . . 8-29

DDAU Configuration

Temperature sensor configuration . . . . . . . . . . . . . . . 3-67

Default password . . . . . . . . . . . 2-10Description . . . . . . . . . . . . . . . . 3-56Device Installation . . . . . . . . . . . . 3-3

antenna type . . . . . . . . . . . 3-51Device installation wizard . . . . . 3-23Diagnostic Registers . . . . . . . . . 8-25Digital Alarms . . . . . . . . . . . . . . 3-17Dipping Datum Plate . . . . 3-63, 3-80Dipping Datum Point . . . . 3-63, 3-80Display Unit . . . . . . . . . . . . . . . . 3-53

EEcho Peaks . . . . . . . . . . . . . . . . 8-18Egpudev.ini . . . . . . . . . . . 3-94, 3-95Enable check box . . . . . . . . . . . . 3-6Enraf GPU Master . . . . . . . . . . . 3-91Error Limits . . . . . . . . . . . . . . . . 3-56

Exclude From Average Calculation . . . . . . . . . . . . . . . . . . . . . . 3-54, 3-78

FFCU . . . . . . . . . . . . . . . . . . . . . . . 3-2

communication setup . . . . . 3-24configuration . . . . . . . . . . . 3-25device type . . . . . . . . . . . . . 3-23redundancy . . . . . . . . . . . . 3-25Slave Database . . . . . . . . . 3-66slave database setup . . . . . 3-26

FCU Configurationslave database . . . . . . . . . . 3-26

FCU Slave Database . . . 3-26, 3-27FCU Slave Positions . . . . . . . . . 3-35Field Communication Unit . . . . . . 3-2File Info Option . . . . . . . . . . . . . 9-11File Log tab . . . . . . . . . . . . . . . . . 5-5Filter Factor . . . . . . . . . . . . . . . . 3-56Filtering options . . . . . . . . . . . . . . 5-6Find Devices . . . . . . . . . . . . . . . . 5-8First and second set points . . . . 3-58Free Water Level . . . . . . . . . . . . 3-35Function Code . . . . . . . . . . . . . . . 5-7FWL . . . . . . . . . . . . . . . . . . . . . . 3-35

GGauge Reference Point . . 3-64, 8-17Group Bus . . . . . . . . . . . . . . . . . 3-26

HHandshaking . . . . . . . . . . . . 3-6, 3-9Hart Devices Configuration . . . . 3-62Hold Off Distance . 3-64, 3-65, 3-82Holding Registers

Viewing . . . . . . . . . . . . . . . . 8-6Holding registers . . . . . . . . . . . . . 8-7Holdoff Distance . . . . . . . . . . . . 8-17Hysteresis . . . . . . . . . . . . . . . . . 3-58

IIcons . . . . . . . . . . . . . . . . . . . . . . 2-9Illegal characters . . . . . . . . . . . . . 1-6Inactivity Timeout . . . . . . . . . . . 2-16Inner diameter . . . . . . . . . 3-52, 3-76Input Registers . . . . . . . . . . . . . . 8-6


Rosemount TankMaster WinSetupReference Manual

303027EN, Edition 4January 2008

InstallNew device . . . . . . . . . . . . . 2-4New tank . . . . . . . . . . . . . . . 2-4

Interval 1 . . . . . . . . . . . . . . . . . . 3-27Interval 2 . . . . . . . . . . . . . . . . . . 3-27Inventory . . . . . . . . . . . . . . . . . . 3-16Inventory calculations . . . . . . . . 3-14IOT

Overview . . . . . . . . . . . . . . 8-27

LLiquid Pressure . . . . . . . . . . . . . 3-35Local Gravity . . . . . . . . . . . . . . . 3-16Log File Configuration . . . . . . . . 3-12Log On . . . . . . . . . . . . . . . . . . . 2-10Log Schedule . . . . . . . . . . . . . . 3-12Logical view . . . . . . . . . . . . . . . . . 2-6LPG Configuration

Air Correction . . . . . . . . . . 3-102Calibrate . . . . . . . . . . . . . . 3-104Calibration Distance . . . . . 3-104Check the ball valve . . . . . 3-102Choose correction method 3-107config pins . . . . . . . . . . . . 3-104reference pins . . . . . . . . . 3-104Vapor Pressure Source . . 3-103Vapor Temperature Source 3-103verify . . . . . . . . . . . . . . . . 3-106

LPG/LNG GaugeCalibration Handle . . . . . . 3-106

MManual . . . . . . . . . . . . . . . . . . . . 5-6Manual values . . . . . . . . . . . . . . 3-39Master Protocol . . . . . . . . . . . . . . 3-2Master protocol channel

log file configuration . . . . . . 3-12Master protocol server . . . . . . . . 1-2Max Log Files . . . . . . . . . . . . . . 3-12Maximum File Size . . . . . . 3-12, 5-5Measuring units . . . . . . . . 3-14, 3-30Menu bar . . . . . . . . . . . . . . . . . . . 2-3Minimum Distance . . . . . . 3-55, 3-78Minimum Level Distance (C) 3-63, 3-80Miscellaneous . . . . . . . . . . . . . . 3-17Modem . . . . . . . . . . . . . . . . 3-6, 3-9

OOpen Tank View . . . . . . . . . . . . . 6-2Operator . . . . . . . . . . . . . . . . . . 2-10Overview IOT . . . . . . . . . . . . . . 8-27

PParity . . . . . . . . . . . . . . . . . . 3-6, 3-9

Passworddefault . . . . . . . . . . . . . . . . 2-10OPER . . . . . . . . . . . . . . . . 2-10SUPER . . . . . . . . . . . . . . . 2-10

Physical view . . . . . . . . . . . . . . . 2-6Pipe Diameter . . . . . . . . . . . . . . 3-52Port . . . . . . . . . . . . . . . . . . . 3-6, 3-9Position in FCU 3-48, 3-50, 3-72, 3-74Predefined . . . . . . . . . . . . . . . . . 8-6Preferences . . . . . . . . . . . 3-2, 3-14Previous Peaks . . . . . . . . . . . . . 8-18Pro

Antenna Type . . . . . . . . . . 3-75Minimum Level Distance (C) 3-80Pipe Diameter . . . . . . . . . . 3-76Tank Connection Length . . 3-82Tank Reference Height (R) 3-80Tank Reference Point . . . . 3-80

Pro Configuration window . . . . . 3-73Pro Gauge

Installation . . . . . . . . . . . . . 3-71Pro Reference Distance (G) . . . 3-80Protection Level . . . . . . . . . . . . 2-14Protection levels . . . . . . . . . . . . 2-10Protocol Channel

activate . . . . . . . . . . . . . . . . 3-6enable check box . . . . . . . . 3-6

Protocol channel statistics . . . . . 5-1Protocol Properties window . . . . 3-5Protocol Server . . . . . . . . . . . . . 3-13Protocol statistics . . . . . . . . . . . . 5-1

RRange Value . . . . . . . . . . 3-57, 3-79RDU . . . . . . . . . . . . . . . . . . . . . 3-53Redundancy . . . . . . . . . . . . . . . 3-25Reference pins

threshold value . . . . . . . . 3-105Reference temperature . . . . . . . 3-17Relay Functions . . . . . . . . . . . . 3-61Relay output configuration

Control Mode . . . . . . . . . . . 3-59First and second set points 3-58hysteresis . . . . . . . . . . . . . 3-58manual control . . . . . . . . . . 3-59normally closed . . . . . . . . . 3-60normally open . . . . . . . . . . 3-60Relay functions . . . . . . . . . 3-61relay states . . . . . . . . . . . . 3-59REX . . . . . . . . . . . . . . . . . . 3-58select source . . . . . . . . . . . 3-59switch delay . . . . . . . . . . . . 3-59toggle period . . . . . . . . . . . 3-59using first/both points . . . . 3-58

Relay states . . . . . . . . . . . . . . . 3-59Remote Display Unit . . . . . . . . . 3-53

Reply timeout . . . . . . . . . . . . . . . .3-6Restore . . . . . . . . . . . . . . . . . . . .9-7Retries . . . . . . . . . . . . . . . . . . . . .3-6Rex Configuration window . . . . .3-49Rex Reference Distance (G) . . .3-63RS232 . . . . . . . . . . . . . . . . . . . . .1-1RS485 . . . . . . . . . . . . . . . . . . . . .1-1RTG Reference Distance (G) . .3-63RTG Reference Point 3-63, 3-64, 3-65, . . . . . . . . . . . . . . . . . . . . . . . . . .3-80

SSave to File . . . . . . . . . . . . . . . .9-11Select Source . . . . . . . . . . . . . .3-59Sensor Position . . . . . . . .3-54, 3-77Sensor Range . . . . . . . . .3-54, 3-77Server Preferences . . . . . . . . . .3-14Set Inactivity Timeout . . . . . . . .2-16Set password . . . . . . . . . . . . . . .2-15Set Required Access Levels . . .2-13Setup Tank View . . . . . . . .3-19, 6-1Several Files Option . . . . . . . . .3-12Slave Database . . . . . . . .3-26, 3-27Slave database . . . . . . . . . . . . . .3-2Slave Protocol . . . . . . . . . . . . . . .3-2Slave protocol channel

tank mapping configuration 3-11TRL/2 Modbus Communication

setup . . . . . . . . . . .3-8Slave Protocol Server . . . . . . . . .1-3Slave type . . . . . . . . . . . . . . . . .3-26Software modules . . . . . . . . . . . .1-2Statistics . . . . . . . . . . . . . . . . . . .5-1Status bar . . . . . . . . . . . . . . . . . .2-5Still-pipe . . . . . . . . . . . . . .3-52, 3-76Stop bits . . . . . . . . . . . . . . . .3-6, 3-9Sub Level Descriptions . . . . . . .2-12Summary Tank View . . . . . . . . . .6-1Supervisor . . . . . . . . . . . . . . . . .2-10Switch Delay . . . . . . . . . . . . . . .3-59Synchronize with FCU . . . . . . . .3-66System Setup . . . . . . . . . . . . . .3-30

TTag Prefixes . . . . . . . . . . . . . . . .3-18Tank Capacity Table . . . . . . . . .3-17Tank configuration . . . . . . . . . . .3-35Tank Connection Length .3-65, 3-82Tank Distances

Minimum Level Distance (C) 3-63, . . . . . . . . . . . . . . .3-80

Pro Reference Distance (G) 3-80REX Reference Distance (G) 3-63Tank Reference Height (R) 3-63,

. . . . . . . . . . . . . . .3-80

Index-2

Rosemount TankMaster WinSetupReference Manual 303027EN, Edition 4January 2008

Tank installation . . . . . . . . . . . . . 3-3advanced tank configuration 3-37associate devices . . . . . . . 3-34tank configuration . . . . . . . 3-35tank type . . . . . . . . . . . . . . 3-33value entry . . . . . . . . . . . . . 3-39

Tank mapping . . . . . . . . . . . . . . . 3-4Tank mapping configuration . . . 3-11Tank Ref Point . . . . . . . . . . . . . 3-63Tank Reference Height (R) 3-63, 3-80Tank Reference Point . . . 3-63, 3-80Tank Scan . . . . . . . . . . . . . . . . 8-13

Action Buttons . . . . . . . . . . 8-22Editing . . . . . . . . . . . . . . . . 8-23File Storage . . . . . . . . . . . . 8-19

Tank Server . . . . . . . . . . . . . . . . 1-2Tank types . . . . . . . . . . . . . . . . 3-33Tank View . . . . . . . . . . . . . . . . . . 6-1Tank View window . . . . . . . . . . . 6-2TankMaster . . . . . . . . . . . . . . . . . 1-1TankMaster Administrator . . . . . 9-1TCL . . . . . . . . . . . . . . . . . 3-65, 3-82TCT . . . . . . . . . . . . . . . . . . . . . . 3-17Temperature Sensor Configuration .. . . . . . . . . . . . . . . . . . . . . 3-53, 3-77

Average Temperature Calculation . . . . . . . . . . . . . . . 3-78

Minimum Distance . . . . . . . 3-78

Temperature sensor configuration 3-67average temperature calculation

. . . . . . . . . . . . . . . .3-54minimum distance . . . . . . . .3-55sensor position . . . . .3-54, 3-77sensor range . . . . . . .3-54, 3-77sensor type . . . . . . . .3-53, 3-77

Timeout . . . . . . . . . . . . . . . . . . .2-16Toggle Period . . . . . . . . . . . . . .3-59Toolbar . . . . . . . . . . . . . . . . . . . . .2-4Tools Menu . . . . . . . . . . . . . . . .8-29TRL PU . . . . . . . . . . . . . . . . . . .3-84

UUFM . . . . . . . . . . . . . . . . .3-65, 3-82Uninstall . . . . . . . . . . . .2-4, 4-3, 4-5Uninstall device . . . . . . . . . . . . . .4-3Units . . . . . . . . . . . . . . . . . . . . . .3-14User Defined antenna . . .3-52, 3-76User Defined Linearization Table 8-4User management

Administrator . . . . . . . . . . .2-10Operator . . . . . . . . . . . . . . .2-10Supervisor . . . . . . . . . . . . .2-10

VValue Entry . . . . . . . . . . . . . . . .3-41

Value Range . . . . . . . . . . 3-39, 3-56Value Unit . . . . . . . . . . . . . . . . . 3-56Vapor Pressure . . . . . . . . . . . . . 3-35Vapor Pressure Source . . . . . . 3-103Vapor Temperature . . . . . . . . . . 3-35Vapor Temperature Source . . 3-103View Log . . . . . . . . . . . . . . . . . . . 5-3View Only . . . . . . . . . . . . . . . . . 2-10Viewing Input and Holding Registers

predefined . . . . . . . . . . . . . . 8-6

WWeight in Air . . . . . . . . . . . . . . . 3-16WIA . . . . . . . . . . . . . . . . . . . . . . 3-16WinOpi . . . . . . . . . . . . . . . . . . . . 1-2WinSetup . . . . . . . . . . . . . . . . . . 1-2

supported devices . . . . . . . 3-44Wizards . . . . . . . . . . . . . . . . . . . . 1-6Workspace . . . . . 2-1, 2-2, 2-4, 2-7

Logical view . . . . . . . . . . . . . 2-6Physical view . . . . . . . . . . . . 2-6

Write new calibration data to RTG . .. . . . . . . . . . . . . . . . . . . . . . . . . 3-121

ZZero level . . . . . . . 3-63, 3-64, 3-80Zero Reference . . . . . . . . 3-64, 8-17

Index-3

Rosemount TankMaster WinSetupReference Manual

303027EN, Edition 4January 2008

Index-4

Reference Manual303027 En, Edition 4January 2008

Copyright © Rosemount Tank Radar AB.Ref. no: 303027EN, Edition 4. January 2008.

Emerson Process ManagementRosemount Tank GaugingBox 130 45SE-402 51 GöteborgSWEDENTel (International): +46 31 337 00 00Fax (International): +46 31 25 30 22E-mail: [email protected]

Documents

Inventory Management Software - Emerson · Rosemount TankMaster WinSetup Inventory Management Software Cover Photo: ... Foundation: ). Customized views