Introduction Pre-Installation Procedure - IP Video Management

Installation Procedure

Windows® Server 2012 / Windows® 8

On-Net Surveillance Systems, Inc. | One Blue Hill Plaza, 7th Floor, Pearl River, NY 10965 | Tel: 845-732-7900 | Fax: 845-732-7999 | www.onssi.com | [email protected]

Introduction When installing Ocularis version 3.0 or 3.5 on a Windows Server 2012 or Windows 8 operating system, you will need to perform a few additional steps before installing the Ocularis Base software component to ensure compatibility and functionality. These steps are necessary to ensure that IIS services and components are setup correctly in order for the Ocularis Base to function properly. If you are not installing Ocularis Base, you may skip the Pre-Installation Procedure and jump to the specific Ocularis component instructions which start on page 8.

Pre-Installation Procedure Perform the following steps on the server or PC where Ocularis Base is to reside:

Installation on Windows Server 2012 (below)

Installation on Windows 8 (on page 6)

Installation on Windows Server 2012

1. On the Windows Server 2012 machine, open Server Manager. Then click Manage and select Add Roles.

Figure 1 Select Installation Type

2. Keep the default selection at Role-based or feature-based installation and click Next.




Figure 2 Select Destination Server

3. On the Select Destination Server screen, you can select a server from a server pool. Select the server for Ocularis Base (which is likely the default, and only server listed), and click Next.

Figure 3 Select Server Roles

4. On the Select Server Roles screen, check the Web Server (IIS) checkbox. The following pop-up will appear:




Figure 4 Add Features for IIS

5. The Include management tools (if applicable) box should already be checked (if not check it to enable). Click Add Features.

6. On the Select Server Roles screen click Next.

Figure 5 Remove Features

7. On the Select features screen, make sure the following services are checked.

a. .NET Framework 3.5 (includes .NET 2.0 and 3.0)

b. HTTP Activation




When you check HTTP Activation, you will get a similar pop-up to the one shown in Figure 4. Ensure that the Include management tools (if applicable) box is checked (if not check it to enable). Click Add Features.

c. .NET Framework 4.5 Features

d. .NET Framework 4.5

e. ASP .NET 4.5

f. WCF Services -> HTTP Activation

When you check HTTP Activation, you will get a similar pop-up to the one shown in Figure 4. Ensure that the Include management tools (if applicable) box is checked (if not check it to enable). Click Add Features.

g. Message Queuing (not shown in Figure 5; you must scroll down the list to find this option)

Once all these items are checked, click Next.

Figure 6 Select Role Services

8. On the Select Role Services screen, make sure the following services are checked (to be installed):

a. Common HTTP Features

i. Default Document




ii. Directory Browsing

iii. HTTP Errors

iv. Static Content

b. Health and Diagnostics

i. HTTP Logging

c. Performance

i. Static Content Compression

d. Security

i. Request Filtering

On the second half of the list, make sure the following services are installed. Click Add Features on any windows that may pop up.

Figure 7 Select Role Services (cont’d)

9. When all the above items have been checked, click Next.

10. On the Summary page, click Install. Wait until services have completed installing.

11. Close the Server Manager.

12. Proceed with the installation of Ocularis as discussed in Installing Ocularis Components on page 8.




Installation on Windows 8

1. On Windows 8, open Control Panel -> Programs and Features.

2. Select the Turn Windows features on or off option.

3. In the resulting Windows Features pop-up, be sure to check the following as shown in Figure 8 and Figure 9 below:

Figure 8 Windows Features to be enabled (screen 1)




Figure 9 Windows Features to be enable (screen 2)

4. When ready, click OK.

5. You will be prompted to download files from Windows Update in order to complete the installation. Be sure to allow this download.

6. When the update is complete, you will be prompted to restart your computer. Restart the computer in order to continue with the installation.

7. Proceed with the installation of Ocularis as discussed in Installing Ocularis Components on page 8.




Installing Ocularis Components This section focuses specifically on special installations steps required for each Ocularis component and is broken into:

Ocularis Base

Ocularis Administrator

Ocularis Recording Components & Event Proxy

Ocularis Client

Ocularis Base

1. Prior to installation, follow the steps found in the Pre-Installation Procedure on page 1.

2. Launch the Ocularis Base executable file in the Installers directory:

C:\Ocularis [xx] Installer\Installers

and proceed with the normal installation. (Refer to the Ocularis Installation and Licensing Guide for detailed instructions). Be sure to keep track of the directory paths of where files are stored.

3. Towards the end of the installation you be will presented with a screen that states:

Figure 8 Ocularis Base Licensing Message

4. Click OK.

5. Proceed with the remainder of the installation. It should complete successfully and it will ask you if you want to 'Activate Base License'. At this time, do not license the software.

6. Either click Cancel or uncheck the box and click OK to exit the installer.

The Ocularis Base installer file will now need to be run again in compatibility mode.

To Enable Compatibility Mode for Ocularis Base

1. You will need to locate the installation file for Ocularis Base that was extracted from the original download file. In most cases, if the default paths were used, this file should be located in:


Where [xx] is the feature set of Ocularis such as: CS

2. From Windows Explorer, right-click the file Ocularis Base.exe.




3. From the resulting pop-up, click the Compatibility tab.

4. Check the box: Run this program in compatibility mode for.

5. Then, from the drop-down list, select Windows 7.

6. Click the Apply button at the bottom and then click OK.

7. Now you can launch the setup and re-install Ocularis Base.

Figure 9 Setting Compatibility Mode

Ocularis Administrator

This component may be installed on Windows 8 or Windows Server 2012 as normal with no additional installation steps required. Keep in mind that this component requires a higher level video card than that which is typically included with server based hardware.

Ocularis Client

Compatibility mode will need to be enabled in order to install Ocularis Client v3.5 on Windows 8. (We do not recommend installing Ocularis Client on Windows Server 2012).

If you try to launch Ocularis Client when compatibility mode is not enabled, you will see this message:




Figure 10 Compatibility Mode Error Message

To Enable Compatibility Mode for Ocularis Client

1. You will need to locate the installation file for Ocularis Client that was extracted from the original download file. In most cases, if the default paths were used, this file should be located in:



2. From Windows Explorer, right-click the file Ocularis Client.exe.





7. Now launch the setup and install Ocularis Client. You can launch it directly from the executable from step 2 or from the Ocularis Component downloads web page.

Figure 11 Windows Compatibility Mode




Recording Components

For Ocularis PS, Ocularis IS and Ocularis CS

Ocularis PS, Ocularis IS and Ocularis CS

The recorders for these feature sets (RC-P, RC-I and RC-C respectively) will install out of the box. If you are installing these components on the same system as Ocularis Base, be sure to change the local port number for the recorder after installation. (Use the recorder’s Management Application and set the local port number under server access to something other than 80 [e.g. 8080, 82, etc..] as per usual instructions.)

Ocularis RC-C / RC-I Event Proxy

For the event proxy used with Ocularis IS and Ocularis CS, Compatibility Mode will need to be enabled for a successful installation. If you try to launch the proxy when compatibility mode is not enabled, you will get this error message:

Figure 12 Windows Compatibility Mode

To Enable Compatibility Mode for the RC-C / RC-I Event Proxy

1. You will need to locate the installation file for the event proxy that was extracted from the original download file. In most cases, if the default paths were used, this file should be located in:



2. From Windows Explorer, right-click the file RC-C RC-I EventProxy.exe.





7. Now launch the setup and install the event proxy. You can launch it directly from the executable from step 2 or from the Ocularis Component downloads web page.

000112712-09082012-001

Documents

Introduction Pre-Installation Procedure - IP Video Management