Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
INTERIOR INSTALLATION
11 2"11 4"
31 2" SYS
TEM
DEPT
H 12" MAX CRC
OVERHANG, TYP.
48" MAX HANGER WIRE
SPACING, TYP.
12" MAX SNAP BAR
OVERHANG, TYP.
48" MAX CRC
SPACING, TYP.
24" SNAP BAR
SPACING, TYP.
'B'
SECTION 'A'SCALE: 3" = 1'-0"
PANEL SPECIFICATIONSSEE DETAIL A1.1
'A'
FLOATING TRIM CONDITIONSSEE DETAIL A1.6 AND A1.7*
SNAP BAR CARRIER SPLICESEE DETAIL A1.3
FIXTURE SPECIFICATIONSSEE DETAIL A1.8 AND A1.9
SUSPENSION REQUIREMENTSSEE DETAIL A1.2
WALL TRIM CONDITIONSSEE DETAIL A1.5
1/2" x 1-1/2" 16 GA CRC (PRIMARY CARRIER)AT 48" O.C. MAX SPACING, BY OTHERS, TYP.
SNAP-IN PANEL
HEAVY-DUTY SNAP BAR(SECONDARY CARRIER)
CROSS CONNECTOR CLAMP
SECTION 'B'SCALE: 3" = 1'-0"
31 2" SYS
TEM
DEPT
H
1/2" x 1-1/2" 16 GA CRC (PRIMARY CARRIER)AT 48" O.C. MAX SPACING, BY OTHERS, TYP.
SNAP-IN PANEL
HEAVY-DUTY SNAP BAR(SECONDARY CARRIER)
CROSS CONNECTOR CLAMP
*TRIM NOT SHOWN FOR CLARITY
12 GA HANGER WIRE, BY OTHERS,NOT BY CERTAINTEEDSEE DETAIL A1.2
5015 Oakbrook Parkway, Suite 100
Norcross, GA 30093
O 800 366 4327
F 770 806 0214
www.certainteed.com/architectural
SPECIFICATIONS
(unless noted otherwise)
MATERIAL: .032" | .040" ALUMINUM SNAP-IN PANEL | 24 GA GALV. STEEL
HEAVY-DUTY SNAP BAR SECONDARY CARRIER
FINISH: PAINT | POWDER COAT | LUXACOTE
PERFORATION: SEE DETAIL A1.1
OVERALL ISOMETRIC VIEW
PROJECT: SNAP-IN PRODUCT SPECIFICATIONS
DRAWING NUMBER: SNAP-IN-A1.0
SCALE: AS SHOWN
DRAWN BY: CTA ENGINEERING
DATE: 6/1/21
These drawings show typical conditions for installing the CertainTeed product shown. They should not be construed as a substitute for an
architectural or engineering design and do not reflect the unique requirements of local codes, laws, statutes or regulations that may be applicable
for a specific installation. CertainTeed assumes no liability for the accuracy or completeness of the drawings for a specific installation or the
fitness of the drawings for a particular purpose. The user is advised to consult with local licensed design professionals in order to assure
compliance with all legal requirements. CertainTeed is not licensed to provide professional engineering or architectural services.
PANEL MATERIAL
.032" OR .040" ALUMINUM
PANEL FINISHES
PAINTED & POWDER COATED
DECORATED WOOD FINISH (POWDER COATED)
LUXACOTE
PANEL CONFIGURATIONS
12"WIDTH UP TO 96" LONG
24" WIDTH UP TO 48" LONG
8 SQUARE FEET MAX PANEL SIZE
OTHER SIZES AVAILABLE, CONTACT CERTAINTEED
PERFORATION % OPEN103 20.0%106 16.0%115 12.0%119 8.0%132 20.0%201 19.6%
PERFORATIONS
MAX PANEL SIZE MAY BE LIMITED BASED ON PERFORATIONPATTERN, CONTACT CERTAINTEED
1. LIFT PANEL
2. SNAP PANEL DIMPLES INTO SNAP BAR
SNAP-IN PANEL DIMPLES
CROSS CONNECTOR CLAMP
HEAVY-DUTY SNAP BAR (SECONDARY CARRIER)
1/2" X 1-1/2" 16 GA CRC(PRIMARY CARRIER), BYOTHERS, TYP.
31 2" SYS
TEM
DEPT
H
5015 Oakbrook Parkway, Suite 100
Norcross, GA 30093
O 800 366 4327
F 770 806 0214
www.certainteed.com/architectural
SPECIFICATIONS
(unless noted otherwise)
MATERIAL: .032" | .040" ALUMINUM SNAP-IN PANEL | 24 GA GALV. STEEL
HEAVY-DUTY SNAP BAR SECONDARY CARRIER
FINISH: PAINT | POWDER COAT | LUXACOTE
PERFORATION: SEE DETAIL A1.1
PANEL SPECIFICATIONS
PROJECT: SNAP-IN PRODUCT SPECIFICATIONS
DRAWING NUMBER: SNAP-IN-A1.1
SCALE: AS SHOWN
DRAWN BY: CTA ENGINEERING
DATE: 6/1/21
These drawings show typical conditions for installing the CertainTeed product shown. They should not be construed as a substitute for an
architectural or engineering design and do not reflect the unique requirements of local codes, laws, statutes or regulations that may be applicable
for a specific installation. CertainTeed assumes no liability for the accuracy or completeness of the drawings for a specific installation or the
fitness of the drawings for a particular purpose. The user is advised to consult with local licensed design professionals in order to assure
compliance with all legal requirements. CertainTeed is not licensed to provide professional engineering or architectural services.
INTERIOR INSTALLATION
48" MAX HANGER WIRE SPACING (CRC SPAN)
12" MAX CRC
OVERHANG
12" MAX SNAP
BAR OVERHANG
48" MAX CRC SPACING (SNAP BAR SPAN)
24" X 24" SNAP-IN PANEL
24" SNAP BAR SPACING
(PANEL LENGTH)
1/2" X 1-1/2" 16 GA GALV. CRC (PRIMARY CARRIER)
CROSS CONNECTOR CLAMP
HEAVY-DUTY SNAP BAR(SECONDARY CARRIER)
12 GA HANGER WIRE BY OTHERS'B' 'A'
SECTION 'A'SCALE: 3" = 1'-0"
SECTION 'B'SCALE: 3" = 1'-0"
11 2"11 4" 1/2" x 1-1/2" 16 GA CRC (PRIMARY CARRIER)
AT 48" O.C. MAX SPACING, BY OTHERS, TYP.
SNAP-IN PANEL
HEAVY-DUTY SNAP BAR (SECONDARY CARRIER)
CROSS CONNECTOR CLAMP 1/2" x 1-1/2" 16 GA CRC (PRIMARY CARRIER)AT 48" O.C. MAX SPACING, BY OTHERS, TYP.
SNAP-IN PANEL
CROSS CONNECTOR CLAMP
31 2"11 4"
HEAVY-DUTY SNAP BAR(SECONDARY CARRIER)
117 32"
5015 Oakbrook Parkway, Suite 100
Norcross, GA 30093
O 800 366 4327
F 770 806 0214
www.certainteed.com/architectural
SPECIFICATIONS
(unless noted otherwise)
MATERIAL: .032" | .040" ALUMINUM SNAP-IN PANEL | 24 GA GALV. STEEL
HEAVY-DUTY SNAP BAR SECONDARY CARRIER
FINISH: PAINT | POWDER COAT | LUXACOTE
PERFORATION: SEE DETAIL A1.1
2'-0" X 2'-0" PANEL SUSPENSION SPECIFICATIONS
PROJECT: SNAP-IN PRODUCT SPECIFICATIONS
DRAWING NUMBER: SNAP-IN-A1.2
SCALE: AS SHOWN
DRAWN BY: CTA ENGINEERING
DATE: 6/1/21
These drawings show typical conditions for installing the CertainTeed product shown. They should not be construed as a substitute for an
architectural or engineering design and do not reflect the unique requirements of local codes, laws, statutes or regulations that may be applicable
for a specific installation. CertainTeed assumes no liability for the accuracy or completeness of the drawings for a specific installation or the
fitness of the drawings for a particular purpose. The user is advised to consult with local licensed design professionals in order to assure
compliance with all legal requirements. CertainTeed is not licensed to provide professional engineering or architectural services.
INTERIOR INSTALLATION
48" MAX HANGER WIRE SPACING (CRC SPAN)
12" MAX CRC
OVERHANG
12" MAX SNAP
BAR OVERHANG
48" MAX CRC SPACING (SNAP BAR SPAN) 48" SNAP BAR SPACING
(PANEL LENGTH)
1/2" X 1-1/2" 16 GA GALV. CRC (PRIMARY CARRIER)
CROSS CONNECTOR CLAMP
HEAVY-DUTY SNAP BAR(SECONDARY CARRIER)
12 GA HANGER WIRE BY OTHERS
24" X 48" SNAP-IN PANEL
'B' 'A'
SECTION 'A'SCALE: 3" = 1'-0"
SECTION 'B'SCALE: 3" = 1'-0"
11 2"2" 1/2" x 1-1/2" 16 GA CRC (PRIMARY CARRIER)
AT 48" O.C. MAX SPACING, BY OTHERS, TYP.
SNAP-IN PANEL
HEAVY-DUTY SNAP BAR (SECONDARY CARRIER)
CROSS CONNECTOR CLAMP 1/2" x 1-1/2" 16 GA CRC (PRIMARY CARRIER)AT 48" O.C. MAX SPACING, BY OTHERS, TYP.
SNAP-IN PANEL
CROSS CONNECTOR CLAMP
2"
HEAVY-DUTY SNAP BAR(SECONDARY CARRIER)
117 32" 31 2"
5015 Oakbrook Parkway, Suite 100
Norcross, GA 30093
O 800 366 4327
F 770 806 0214
www.certainteed.com/architectural
SPECIFICATIONS
(unless noted otherwise)
MATERIAL: .032" | .040" ALUMINUM SNAP-IN PANEL | 24 GA GALV. STEEL
HEAVY-DUTY SNAP BAR SECONDARY CARRIER
FINISH: PAINT | POWDER COAT | LUXACOTE
PERFORATION: SEE DETAIL A1.1
2'-0" X 4'-0" PANEL SUSPENSION SPECIFICATIONS
PROJECT: SNAP-IN PRODUCT SPECIFICATIONS
DRAWING NUMBER: SNAP-IN-A1.3
SCALE: AS SHOWN
DRAWN BY: CTA ENGINEERING
DATE: 6/1/21
These drawings show typical conditions for installing the CertainTeed product shown. They should not be construed as a substitute for an
architectural or engineering design and do not reflect the unique requirements of local codes, laws, statutes or regulations that may be applicable
for a specific installation. CertainTeed assumes no liability for the accuracy or completeness of the drawings for a specific installation or the
fitness of the drawings for a particular purpose. The user is advised to consult with local licensed design professionals in order to assure
compliance with all legal requirements. CertainTeed is not licensed to provide professional engineering or architectural services.
'A'
'B' IF THE DESIRED HEAVY-DUTY SNAP BARLENGTH EXCEEDS THE MAXIMUM OF 16'-0",USE A SNAP-IN PROFILE SPLICE TO CONNECTTHE FACTORY SNAP-IN PROFILE ENDS.
THE SHEAR TABS WILL SECURE THE SPLICEAND ADDITIONAL FASTENERS ARE NOTREQUIRED.
24" X 24" SNAP-IN PANEL
HEAVY-DUTY SNAP BAR(SECONDARY CARRIER)
SECTION 'A'SCALE: FULL
SECTION 'B'SCALE: 3" = 1'-0"
5015 Oakbrook Parkway, Suite 100
Norcross, GA 30093
O 800 366 4327
F 770 806 0214
www.certainteed.com/architectural
SPECIFICATIONS
(unless noted otherwise)
MATERIAL: .032" | .040" ALUMINUM SNAP-IN PANEL | 24 GA GALV. STEEL
HEAVY-DUTY SNAP BAR SECONDARY CARRIER
FINISH: PAINT | POWDER COAT | LUXACOTE
PERFORATION: SEE DETAIL A1.1
HEAVY-DUTY SNAP BAR SPLICE
PROJECT: SNAP-IN PRODUCT SPECIFICATIONS
DRAWING NUMBER: SNAP-IN-A1.4
SCALE: AS SHOWN
DRAWN BY: CTA ENGINEERING
DATE: 6/1/21
These drawings show typical conditions for installing the CertainTeed product shown. They should not be construed as a substitute for an
architectural or engineering design and do not reflect the unique requirements of local codes, laws, statutes or regulations that may be applicable
for a specific installation. CertainTeed assumes no liability for the accuracy or completeness of the drawings for a specific installation or the
fitness of the drawings for a particular purpose. The user is advised to consult with local licensed design professionals in order to assure
compliance with all legal requirements. CertainTeed is not licensed to provide professional engineering or architectural services.
CORRECT REMOVALSCALE: 3" = 1'-0"
VIEW FROM BELOWSCALE: NTS
SNAP-INDIMPLE SIDE
CORRECT LOCATION
HEAVY-DUTY
SNAP BAR DIRECTION 1/2" x 1-1/2"
16 GA CRC DIRECTION
TO FIND CORRECT LOCATION FOR ACCESS TOOL, INSERT ACCESSTOOL AT PANEL INTERSECTION. ALIGN EDGE OF BLADE WITHEDGE OF PANEL. IF INSERTED IN PROPER LOCATION, YOU SHOULDHEAR A "CLICK" SOUND AND THE WOODEN HANDLE WILL SEATFLUSH AGAINST THE PANEL FACE. IF NOT INSERTED IN PROPERLOCATION, BLADE WILL STOP BEFORE WOOD HANDLE SEATS. IFTHIS HAPPENS, REMOVE TOOL AND INSERT IN ADJACENT PANELEDGE. (AROUND THE CORNER).
ACCESS TOOL(PART # T63165)
NOTE: 5 BLADES INCLUDEDWITH TOOL HANDLE.
ADDITIONAL REPLACEMENTBLADES MAY BE ORDERED
CORRECT
INCORRECT
INCORRECT LOCATION
5015 Oakbrook Parkway, Suite 100
Norcross, GA 30093
O 800 366 4327
F 770 806 0214
www.certainteed.com/architectural
SPECIFICATIONS
(unless noted otherwise)
MATERIAL: .032" | .040" ALUMINUM SNAP-IN PANEL | 24 GA GALV. STEEL
HEAVY-DUTY SNAP BAR SECONDARY CARRIER
FINISH: PAINT | POWDER COAT | LUXACOTE
PERFORATION: SEE DETAIL A1.1
ACCESS TOOL SPECIFICATIONS
PROJECT: SNAP-IN PRODUCT SPECIFICATIONS
DRAWING NUMBER: SNAP-IN-A1.5
SCALE: AS SHOWN
DRAWN BY: CTA ENGINEERING
DATE: 6/1/21
These drawings show typical conditions for installing the CertainTeed product shown. They should not be construed as a substitute for an
architectural or engineering design and do not reflect the unique requirements of local codes, laws, statutes or regulations that may be applicable
for a specific installation. CertainTeed assumes no liability for the accuracy or completeness of the drawings for a specific installation or the
fitness of the drawings for a particular purpose. The user is advised to consult with local licensed design professionals in order to assure
compliance with all legal requirements. CertainTeed is not licensed to provide professional engineering or architectural services.
'B'
'A'
FIELD CUT PANEL SIDE
1" WALL ANGLE, USE ANGLE ABOVE ASHOLD DOWN FOR CUT PANEL EDGE
FIELD CUT PANEL END
1" WALL ANGLE, USE ANGLE ABOVE ASHOLD DOWN FOR CUT PANEL EDGE
12'-0" WALL ANGLE TRIM
1"1"1" WALL ANGLE
0.025" ALUMINUMFINISH TO MATCH, TYP.
SECTION 'A'SCALE: 3" = 1'-0"
SECTION 'B'SCALE: 3" = 1'-0"
HEAVY-DUTY SNAP BAR(SECONDARY CARRIER)
24" X 24" SNAP-IN PANEL
*VERTICAL SUPPORT OMITTED FOR CLARITY
1/2" X 1-1/2" 16 GA GALV. CRC(PRIMARY CARRIER)
CROSS CONNECTOR CLAMP
1" WALL ANGLE TRIM
FIELD MITER TRIMSAT CORNERS
FIELD CUT ALL SNAP-INPANEL SIDES FOR WIDTH
AS REQUIRED, TYP.
FIELD CUT ALL SNAP-IN PANEL ENDSFOR LENGTH AS REQUIRED, TYP.
1" WALL ANGLE HOLD DOWN TO SECURE FIELDCUT PANEL SIDES AND ENDS. HOLD DOWNNOT REQUIRED AT FULL PANEL EDGES.
HEAVY-DUTY SNAP BAR(SECONDARY CARRIER)
8" MAX CRC SPACING (SNAP BAR SPAN)
48" MAX CRC SPACING (SNAP BAR SPAN)
12" MAX OVERHANG
1/2" X 1-1/2" 16 GA CRC(PRIMARY CARRIER), BY OTHERS, TYP.
5015 Oakbrook Parkway, Suite 100
Norcross, GA 30093
O 800 366 4327
F 770 806 0214
www.certainteed.com/architectural
SPECIFICATIONS
(unless noted otherwise)
MATERIAL: .032" | .040" ALUMINUM SNAP-IN PANEL | 24 GA GALV. STEEL
HEAVY-DUTY SNAP BAR SECONDARY CARRIER
FINISH: PAINT | POWDER COAT | LUXACOTE
PERFORATION: SEE DETAIL A1.1
WALL ANGLE TRIM
PROJECT: SNAP-IN PRODUCT SPECIFICATIONS
DRAWING NUMBER: SNAP-IN-A1.6
SCALE: AS SHOWN
DRAWN BY: CTA ENGINEERING
DATE: 6/1/21
These drawings show typical conditions for installing the CertainTeed product shown. They should not be construed as a substitute for an
architectural or engineering design and do not reflect the unique requirements of local codes, laws, statutes or regulations that may be applicable
for a specific installation. CertainTeed assumes no liability for the accuracy or completeness of the drawings for a specific installation or the
fitness of the drawings for a particular purpose. The user is advised to consult with local licensed design professionals in order to assure
compliance with all legal requirements. CertainTeed is not licensed to provide professional engineering or architectural services.
FIELD MITERTRIMS ATCORNERS
12 GA HANGER WIREBY OTHERS, TYP.
SECTION 'A'SCALE: 3" = 1'-0"
SECTION 'B'SCALE: 3" = 1'-0"
FIELD CUT PANEL END
SNAP-IN TRIM FOR FIELD CUT PANEL
1/2" X 1-1/2" 16 GA CRC(PRIMARY CARRIER), BY OTHERS, TYP.
12 GA HANGER WIRE BY OTHERS
FIELD CUT PANEL SIDE
SNAP-IN TRIM FOR FIELD CUT PANEL
HEAVY-DUTY SNAP BAR (SECONDARY CARRIER)
CROSS CONNECTOR CLAMP
1/2" X 1-1/2" 16 GA CRC (PRIMARY CARRIER), BY OTHERS, TYP.
SUPPLEMENTAL CRC & HANGER WIRE FOR TRIM SUPPORT BY OTHERS
CLIP ANGLE TO SECURE SUPPLEMENTALCRC TO PRIMARY CARRIER, BY OTHERS
12 GA HANGER WIRE BY OTHERS, TYP.
SUPPLEMENTAL CRC & HANGERWIRE FOR TRIM SUPPORT BY
OTHERS. SECURE TO PRIMARYCARRIER WITH CLIP ANGLE.
'A' 'B'
SNAP-IN FLOATING TRIM0.032" ALUMINUMFINISH TO MATCH, TYP.
POP RIVET BOX MOLD TO TRIM, BY OTHERS
HOLD DOWN CLIP
10'-0" SNAP-IN FLOATING
TRIM FOR FIELD CUT PANEL
3-1/
2" N
OM.
2" N
OM.
1-1/2"
1"
1/2" X 1-1/2" 16 GA GALV. CRC(PRIMARY CARRIER)
CROSS CONNECTOR CLAMP
HEAVY-DUTY SNAP BAR(SECONDARY CARRIER)
24" X 24" SNAP-IN PANEL
BOX MOLD TRIM0.025" ALUMINUMFINISH TO MATCH, TYP.
10'-0" BOX MOLD TRIM
1-3/
4"
1"
11" CLIP PART LENGTH POP RIVET BOX MOLD TO TRIM, BY OTHERS
HOLD DOWN CLIP
48" MAX CRC SPACING (SNAP BAR SPAN)
12" MAX OVERHANG
5015 Oakbrook Parkway, Suite 100
Norcross, GA 30093
O 800 366 4327
F 770 806 0214
www.certainteed.com/architectural
SPECIFICATIONS
(unless noted otherwise)
MATERIAL: .032" | .040" ALUMINUM SNAP-IN PANEL | 24 GA GALV. STEEL
HEAVY-DUTY SNAP BAR SECONDARY CARRIER
FINISH: PAINT | POWDER COAT | LUXACOTE
PERFORATION: SEE DETAIL A1.1
FIELD CUT FLOATING TRIM
PROJECT: SNAP-IN PRODUCT SPECIFICATIONS
DRAWING NUMBER: SNAP-IN-A1.7
SCALE: AS SHOWN
DRAWN BY: CTA ENGINEERING
DATE: 6/1/21
These drawings show typical conditions for installing the CertainTeed product shown. They should not be construed as a substitute for an
architectural or engineering design and do not reflect the unique requirements of local codes, laws, statutes or regulations that may be applicable
for a specific installation. CertainTeed assumes no liability for the accuracy or completeness of the drawings for a specific installation or the
fitness of the drawings for a particular purpose. The user is advised to consult with local licensed design professionals in order to assure
compliance with all legal requirements. CertainTeed is not licensed to provide professional engineering or architectural services.
FULL PANEL END
SNAP-IN FLOATING TRIM
1/2" X 1-1/2" 16 GAGALV. CRC (PRIMARY
CARRIER)CROSS CONNECTOR
CLAMP
HEAVY-DUTY SNAP BAR(SECONDARY CARRIER)
24" X 24" SNAP-IN PANEL'A'
HEAVY-DUTY SNAP BAR(SECONDARY CARRIER)
1/2" X 1-1/2" 16 GA CRC (PRIMARYCARRIER), BY OTHERS, TYP.
12 GA HANGER WIRE BY OTHERS
CROSS CONNECTOR CLAMP
FULL PANEL SIDE
SNAP-IN FLOATING TRIM
POP RIVET PANEL TO TRIM, BY OTHERS
CROSS CONNECTOR CLAMP
1/2" X 1-1/2" 16 GA CRC (PRIMARY CARRIER), BY OTHERS, TYP.
SUPPLEMENTAL CRC & HANGER WIRE FOR TRIM SUPPORT BY OTHERS
CLIP ANGLE TO SECURE SUPPLEMENTALCRC TO PRIMARY CARRIER, BY OTHERS
12 GA HANGER WIRE BY OTHERS, TYP.
SECTION 'A'SCALE: 3" = 1'-0"
SECTION 'B'SCALE: 3" = 1'-0"
3-1/
2" N
OM.
1-1/
4" N
OM.
1-1/2"
2"
10'-0" SNAP-IN FLOATING
TRIM PART LENGTH
SNAP-IN FLOATING TRIM
SNAP-IN FLOATING TRIM0.032" ALUMINUMFINISH TO MATCH, TYP.
FIELD NOTCH TOP FLANGE OF TRIM TOCLEAR CROSS CONNECTOR CLAMP
FIELD MITERTRIMS ATCORNERS
SUPPLEMENTAL CRC & HANGERWIRE FOR TRIM SUPPORT BY
OTHERS. SECURE TO PRIMARYCARRIER WITH CLIP ANGLE.
'B'
12" MAX
OVERHANG
12 GA HANGER WIREBY OTHERS, TYP.
HEAVY-DUTYSNAP BAR(SECONDARYCARRIER)
FIELD NOTCHTOP FLANGE OFTRIM TO CLEAR CROSSCONNECTOR CLAMP, TYP.
48" MAX CRC SPACING (SNAP BAR SPAN)
5015 Oakbrook Parkway, Suite 100
Norcross, GA 30093
O 800 366 4327
F 770 806 0214
www.certainteed.com/architectural
SPECIFICATIONS
(unless noted otherwise)
MATERIAL: .032" | .040" ALUMINUM SNAP-IN PANEL | 24 GA GALV. STEEL
HEAVY-DUTY SNAP BAR SECONDARY CARRIER
FINISH: PAINT | POWDER COAT | LUXACOTE
PERFORATION: SEE DETAIL A1.1
FULL PANEL FLOATING TRIM
PROJECT: SNAP-IN PRODUCT SPECIFICATIONS
DRAWING NUMBER: SNAP-IN-A1.8
SCALE: AS SHOWN
DRAWN BY: CTA ENGINEERING
DATE: 6/1/21
These drawings show typical conditions for installing the CertainTeed product shown. They should not be construed as a substitute for an
architectural or engineering design and do not reflect the unique requirements of local codes, laws, statutes or regulations that may be applicable
for a specific installation. CertainTeed assumes no liability for the accuracy or completeness of the drawings for a specific installation or the
fitness of the drawings for a particular purpose. The user is advised to consult with local licensed design professionals in order to assure
compliance with all legal requirements. CertainTeed is not licensed to provide professional engineering or architectural services.
'B'
'B'
SECTION 'B'SCALE: 3" = 1'-0"
SECTION 'A'SCALE: 3" = 1'-0"
*HANGER WIRE OMITTED FOR CLARITY
TYPICAL ISOMETRICSCALE: NOT TO SCALE
INTERIOR INSTALLATION
'A'
'A'
NOTE:FIXTURE OR DIFFUSER MUST BEINDEPENDENTLY SUPPORTED INACCORDANCE WITH LOCAL BUILDING CODESAND MANUFACTURER'S INSTRUCTIONS
3/8"
3 8"
23'-14" CLEAR OPENING
24" SNAP BAR SPACING
1/2" X 1-1/2"16 GA GALV.CRC (PRIMARYCARRIER)
CROSSCONNECTORCLAMP"MT" FLANGE LIGHT
FIXTURE, BY OTHERS**
3/8"
24" X 24"SNAP-IN TILE
2" S
YSTE
MDE
PTH
24" CLEAR OPENINGCROSS
CONNECTORCLAMP
1/2" x 1-1/2"16 GA CRC
(PRIMARY CARRIER),BY OTHERS, TYP.
FULL 24" X 24"SNAP-IN
PANEL, TYP.
HEAVY-DUTY SNAP BAR(SECONDARY CARRIER)
24" CLEAR OPENING23-1/4" CLEAR OPENING
31 2" SYS
TEM
DEPT
H
**RECOMMENDED MFG:LITHONIA: SERIES 2SP MT (OR EQUAL)
24" X 24"SNAP-IN TILE
HEAVY-DUTYSNAP BAR(SECONDARYCARRIER)
"MT" FLANGE LIGHTFIXTURE, BY OTHERS**
HEAVY-DUTYSNAP BAR(SECONDARYCARRIER)
5015 Oakbrook Parkway, Suite 100
Norcross, GA 30093
O 800 366 4327
F 770 806 0214
www.certainteed.com/architectural
SPECIFICATIONS
(unless noted otherwise)
MATERIAL: .032" | .040" ALUMINUM SNAP-IN PANEL | 24 GA GALV. STEEL
HEAVY-DUTY SNAP BAR SECONDARY CARRIER
FINISH: PAINT | POWDER COAT | LUXACOTE
PERFORATION: SEE DETAIL A1.1
2'-0" X 2'-0" FIXTURE OPENING
PROJECT: SNAP-IN PRODUCT SPECIFICATIONS
DRAWING NUMBER: SNAP-IN-A1.9
SCALE: AS SHOWN
DRAWN BY: CTA ENGINEERING
DATE: 6/1/21
These drawings show typical conditions for installing the CertainTeed product shown. They should not be construed as a substitute for an
architectural or engineering design and do not reflect the unique requirements of local codes, laws, statutes or regulations that may be applicable
for a specific installation. CertainTeed assumes no liability for the accuracy or completeness of the drawings for a specific installation or the
fitness of the drawings for a particular purpose. The user is advised to consult with local licensed design professionals in order to assure
compliance with all legal requirements. CertainTeed is not licensed to provide professional engineering or architectural services.
SECTION 'B'SCALE: 3" = 1'-0"
SECTION 'A'SCALE: 3" = 1'-0"
*HANGER WIRE OMITTED FOR CLARITY
TYPICAL ISOMETRICSCALE: NOT TO SCALE
INTERIOR INSTALLATION
NOTE:FIXTURE OR DIFFUSER MUST BEINDEPENDENTLY SUPPORTED INACCORDANCE WITH LOCAL BUILDING CODESAND MANUFACTURER'S INSTRUCTIONS
24" X 24"SNAP-IN TILE
24" CLEAROPENING
24" X 24"SNAP-IN TILE
HEAVY-DUTYSNAP BAR(SECONDARYCARRIER)
CROSSCONNECTOR
CLAMP
FULL 24" X 24"SNAP-IN
PANEL, TYP.
HEAVY-DUTY SNAP BAR(SECONDARY CARRIER)
24" CLEAR OPENING
6" MAX FROMPANEL EDGE
6" MAX FROMPANEL EDGE
6" MAX FROMPANEL EDGE
6" MAX FROMPANEL EDGE
FIXTURE, BY OTHERS,SEE NOTE THIS SHEET
FIXTURE, BY OTHERS,SEE NOTE THIS SHEET
FLANGEDFIXTUREREQUIRED
FLANGED FIXTUREREQUIRED
1/2" x 1-1/2"16 GA CRC
(PRIMARY CARRIER),BY OTHERS, TYP.
'A' 'B''A''B'
6" MAX 6" MAX
2" S
YSTE
MDE
PTH
1/2" X 1-1/2"16 GA GALV.CRC (PRIMARYCARRIER)
31 2" SYS
TEM
DEPT
H
5015 Oakbrook Parkway, Suite 100
Norcross, GA 30093
O 800 366 4327
F 770 806 0214
www.certainteed.com/architectural
SPECIFICATIONS
(unless noted otherwise)
MATERIAL: .032" | .040" ALUMINUM SNAP-IN PANEL | 24 GA GALV. STEEL
HEAVY-DUTY SNAP BAR SECONDARY CARRIER
FINISH: PAINT | POWDER COAT | LUXACOTE
PERFORATION: SEE DETAIL A1.1
FIELD CUT PANEL OPENING
PROJECT: SNAP-IN PRODUCT SPECIFICATIONS
DRAWING NUMBER: SNAP-IN-A1.10
SCALE: AS SHOWN
DRAWN BY: CTA ENGINEERING
DATE: 6/1/21
These drawings show typical conditions for installing the CertainTeed product shown. They should not be construed as a substitute for an
architectural or engineering design and do not reflect the unique requirements of local codes, laws, statutes or regulations that may be applicable
for a specific installation. CertainTeed assumes no liability for the accuracy or completeness of the drawings for a specific installation or the
fitness of the drawings for a particular purpose. The user is advised to consult with local licensed design professionals in order to assure
compliance with all legal requirements. CertainTeed is not licensed to provide professional engineering or architectural services.
SPLAYED 12 GA HANGERWIRE, BY OTHERS, TYP.
COMPRESSIONSTRUT, BY OTHERS
45°
45°
SE
N45°
LATERAL BRACING: BRACE WITH HANGER WIRES AND STRUTS PER ASTM E-580 AND IN ACCORDANCE WITH LOCAL CODE REQUIREMENTS.
(4) #12 GAUGE WIRES SPLAYED 90° FROM EACH OTHER AT ANGLE NOT EXCEEDING 45° FROMPLANE OF CEILING. A STRUT FASTENED TO MAIN RUNNER SHALL BE EXTENDED TO ANDFASTENED TO STRUCTURE ABOVE. SPLAYED WIRE AND STRUT BRACING TO BE PLACED NOTMORE THAN 12 FEET ON CENTER IN EACH DIRECTION, WITH THE FIRST POINT WITHIN 6 FEETFROM EACH WALL.
W45
°
N
SW
E
1/2" x 1-1/2" 16 GA CRC (PRIMARYCARRIER), BY OTHERS, TYP.
HEAVY-DUTY SNAP BAR(SECONDARY CARRIER)
(1) #10 X 1/2" TEK SCREW,BY OTHERS, TYP.
5015 Oakbrook Parkway, Suite 100
Norcross, GA 30093
O 800 366 4327
F 770 806 0214
www.certainteed.com/architectural
SPECIFICATIONS
(unless noted otherwise)
MATERIAL: .032" | .040" ALUMINUM SNAP-IN PANEL | 24 GA GALV. STEEL
HEAVY-DUTY SNAP BAR SECONDARY CARRIER
FINISH: PAINT | POWDER COAT | LUXACOTE
PERFORATION: SEE DETAIL A1.1
SEISMIC SPECIFICATIONS
PROJECT: SNAP-IN PRODUCT SPECIFICATIONS
DRAWING NUMBER: SNAP-IN-A1.11
SCALE: AS SHOWN
DRAWN BY: CTA ENGINEERING
DATE: 6/1/21
These drawings show typical conditions for installing the CertainTeed product shown. They should not be construed as a substitute for an
architectural or engineering design and do not reflect the unique requirements of local codes, laws, statutes or regulations that may be applicable
for a specific installation. CertainTeed assumes no liability for the accuracy or completeness of the drawings for a specific installation or the
fitness of the drawings for a particular purpose. The user is advised to consult with local licensed design professionals in order to assure
compliance with all legal requirements. CertainTeed is not licensed to provide professional engineering or architectural services.