Upload
others
View
8
Download
0
Embed Size (px)
Citation preview
S.NO DESCRIPTION UNITS QTY RATE AMOUNT
A CIVIL WORKS
1 Brick work SQM 52 -Rs.
Providing & laying Brick work masonary with 100mm thick with 1:2:4 concrete bands 100 x
100 mm at every fourth layer
Cement mortar 1:4 (1 cement : 4 coarse sand)
2 Plaster SQM 75 -Rs.
12 mm cement plaster on the rough side of single or half brick wallof mix :
1:4 (1 cement: 4 fine sand)
B FLOORING
1 Italian flooring ( Reception, lounge, Toilet) SQM 264 -Rs.
Providing and laying polished italian marble (Perlato Sicillia or equivalent) of minimum 16-
18mm thickness in flooring, skirting over minimum 5-6 mm thick underbed with white
adhesive PG 400 of ASIAN/LATTICRETE or equivalent .The marble stone slabs laid over under-
bed, pressed and tapped down with wooden mallet to the proper level, lifted and pressed
again with adhesive spread over the surface with fine joint finished including pigments,
curing, grinding, making corners, and finished with diamond polishing etc. all complete as
per drawings, specifications, manufacturer's recommendations, as per pattern in drawing.
(Basic rate Rs. 3300/sm)Item to include diamond polishing to marble. The material will be
apporved by the Engineer in charge / Architect before procurment.
Approx size : 1200 x 900
2 Wooden flooring ( Chairman, MD, DMD, PS, Meeting room ) SQM 292 -Rs.
INTERIOR & FURNISHING WORKS FOR STATE BANK OF INDIA
EXECUTIVE FLOOR, 3RD FLOOR, SBI, LOCAL HEAD OFFICE : JAIPUR
CHAIRMAN AREA
Page 1
S.NO DESCRIPTION UNITS QTY RATE AMOUNTProviding and Laying 11.5 to 12 mm thick Engineered Wood with plank width of 185mm,
Length of 2200mm and top layer of 2.5mm (11.5mm overall)/3.6mm thick natural
hardwood. Surface of top layer is pre finished with several layers of lacquer/natural oil and
UV protective layer. Flooring planks shall be interlocked using Automatic-Click Lock
system.Engineered Wooden planks shall be a composed of 3 layers with right angle and 4
sided non-bevelled/mini-bevelled/bevelled in length and width as specified by the
manufacturer. Product should be installed on a levelled subfloor with floating manner with
using 2mm thik underlay of PU foam & polythene including all Accessories complete.
Equivalent make - Parador, Haro, Juncker. The material will be apporved by the Engineer in
charge / Architect before procurment.
3 Carpet Tile (Meeting room, VC Room) SQM 100 -Rs.
Providing and laying of 6.5 to 7.5mm thick Carpet Tile over the specified area with following
specification. The floor which recieves the carpet to be thourougly cleaned as per
manufacturer's specification. The carpet is to be laid over a bed of manufacturer's approved
adhesive spread evenly over the entire floor. The rate shall include cutting, trimming, fixing
and clearing away of residual material to a location as directed. The rate shall also include
supplying and laying of a protective layer of PVC or HDPE sheet of 50 microns thickness, held
together with scotch tape. The laid carpet to be vacuumed after the removal of protective
cover/on commissioning. If after the protective layer is removed and stains observed in the
carpet because of in adequate protection, the same shall be shampooed and made good to
the satisfaction of the project managers. The measurements of carpet will be the actual laid
area. The material will be apporved by the Engineer in charge / Architect before procurment.
C FALSE CEILING
1 Gypsum Ceiling SQM 665 -Rs.
Page 2
S.NO DESCRIPTION UNITS QTY RATE AMOUNTProviding and fixing false ceiling at all height including providing and fixing of frame work
made of special sections, power pressed from M.S. sheets and galvanized with zinc coating
of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25
mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre,
one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia
bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length
with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I.
channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the
ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each
having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction
perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x
230 mm long G.I.wire at every junction, including fixing perimeter channels 0.5 mm thick 27
mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/
partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @
230 mm interval,
including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and
30 mm long, the perimeter of ceiling fixed to wall/ partition with the help of rawl plugs at
450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of
gypsum board to ceiling section and perimeter channel with the help of dry wall screws of
size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered
and square edges of the board with recommended jointing compound , jointing tapes and
finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint , all
as per manufacturer's specification and also including the cost of making openings for light
fittings, grills, diffusers, fire and other servicsetc complete ,cutouts made with frame of
perimeter channels suitably fixed, including trap door with 19 mm thick Premium quality
BWR gurgen basegrade plywood with moulding in edges including primer and plastic
emulsion paint all complete as per specification and combined services drawings direction
of the Engineer in Charge . No extra will be paid for light cuttings/grills/diffusers, cutouts ,
trap door etc. No extra channel will be paid if its is required for additional support etc.
Page 3
S.NO DESCRIPTION UNITS QTY RATE AMOUNTNote Item includes cove lights in false ceiling as per drawings & instructions & finishing smooth
with three coats of plastic emulsion paint of approved quality.For light fittings, grill diffusers
and cut outs etc. have to be made with the frame of perimeter channels of size Lay on cross
tee twist and rotation for greater stability 20 x 27x30 x 0.55 mm thick, supported suitable.
Angle beads edge beads control joints as required to be provided. The quoted rate to be
include all the above items. Ceiling to be painted with minimum two coats of plastic
emulsion paints over POP punning, base preparation etc. work to be complete as per
drawing and direction of Bank/Architect. (Only flat surface shall be measured and paid)
2 Wooden Ceiling SQM 33.3 -Rs.
Providing and fixing at all height false ceiling of 12 mm thick Premium quality BWR gurgen
baseplyboard , finished with PU polish, including providing and fixing of frame work made of
special sections power pressed from M.S. sheet and galvanized in accordance with zinc
coating 600 as per IS: 277 and consisting of angle cleats of size 25 mm wide X 15 mm thick
with flanges of 22 mm and 37 mm at 1200 mm centre to centre one flange fixed to the
ceiling with dash fastner 12.5 mm dia X 40 mm long with 6 mm dia. Bolts to the angle
hangers of 25 X 25 X 5 mm of required length, and other end of angle hanger being fixed
with nuts and bolts to 6.1 channels 45 mm X 15 mm X 0.9 mm running at the rate of 1200
mm centre to centre to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with
tapered flanges of 26 mm each having clips of 10.5 mm at 450 mm centre to centre shall be
fixed in a direction perpendicular to 6.1 channel with connecting clips made out of 2.64 mm
dia. X 230 mm long 6.1 mm wire at every junction including fixing the gypsum board with
ceiling section and perimeter channels 22 sq.mt.
Page 4
S.NO DESCRIPTION UNITS QTY RATE AMOUNT0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling
fixed to wall/partition with the help of rawl plugs at 450 mm centre to centre with 25 mm
long drive – all screws @ 230 mm interval including joining and fixing to a flush finish. The
wooden ceiling will be finished with the approved 4 mm veneer finished with two coats of
sealer and two coats of melamine polish as per directions and also including the cost of
making openings for light fittings, grills, diffusers, cut outs made with frame of perimeter
channels suitably fixed finishing of all joints neatly to proper line & level including providing
of additional framework for electricals fixtures.including giving trap doors where ever
required. Diffusers,cutouts for fire sprinklers etc. as per the specifications approved by
architects Including necessary scaffolding supports, suspenders etc. All complete as per
drawing and specification and direction of the architect.
3 Baffle Ceiling SQM 17 -Rs.
Providing and fixing Armstrong / hunterdouglas Baffle ceiling
The 5mm Gal rod shall to be cut to pre-determined lengths, and a hook bent to 30° on one
end. (must be a sharp bend, so the suspension bracket will fit into the bend without the rod
straightening)
Fit the Suspension Clip to the rod at this stage.
Ensure all suspension rods are vertical.
Install U-profile Channels at 1200mm (maximum) centres with Suspension Hangers (5mm
Rod and Clip) at 1200mm (maximum) centres along the length of each U-profile Channel
(Item MET111). Ensure Locking Clips are installed to secure the Suspension Clip to the U-
profile Channel. See Fig. 1 for details and specific components: 5mm Rod, Suspension Clip
(item MET203) and Locking Clip (item MET200)
The 1st U-profile Channel must be no more than 400mm from the perimeter
The U-profile Channels are to be installed parallel, in a manner that slots of U-profile are
alligned along the length.
4 Armstrong / Hunter douglas Sound Scapes
Page 5
S.NO DESCRIPTION UNITS QTY RATE AMOUNTProviding and Fixing Armstrong SoundScapes – Blades or equivalent,which are 40 mm thick,
pre-formed fiberglass blades with sizes of 200x1200mm long with laminated scrim finish on
all sides and edges, Acoustical performance of 0.65 NRC in the color specified by the
Architect (Shell / Tangerine / Cranberry / Moss / Kiwi / Reef / Lagoon), Fire Performance
Class B – s1, d0 as per En 13501-1 and having a recycled content of 80%.
Each 16 -Rs.
INSTALLATION WITH DECK HANGING KIT:
The SoundScapes Blades shall be factory fitted with “female inserts” on both sides. The
blades to be suspended individually using the Armstrong Deck Hanging kit comprising of
gripper structure anchors with an outer diameter of 16mm and height 23mm, aircraft cables
of 1.5mm dia 2.44 LM in length and bottom end cable adjusters of 8.9mm outer diameter.
Blades must be installed with minimum 100 mm on-centre spacing.
Hanger Wire Attachment to Structure: Attach the gripper structure anchor to the structure
with a fastener that will carry the full weight of the blades. Insert the end of the cable into
the gripper anchor cap. Screw the gripper anchor cap completely into the gripper structure
anchor.
Insert Suspension Cables: The panel is to be suspended using the aircraft cables which are
suspended from the soffit using the gripper structure anchors and its other end passing
through the bottom end cable adjuster. The height & level of the panels can be adjusted
using the bottom end cable adjusters.
Suspend the Blade: Locate the two factory fitted female inserts on the blades. Suspend the
Blades by screwing the bottom end of the cable adjuster into the female inserts.
Installation to be carried out by Armstrong Trained Installation team & Installation should be
carried out as per Company recommended procedure.
D PARTITION
1 Veneer Partition SQM 240 -Rs.
Page 6
S.NO DESCRIPTION UNITS QTY RATE AMOUNTProviding and fixing 75mm thick partition which includes 8mm Premium quality BWR gurgen
base Plywood both side screw fixed with drywall screw of 25mm at 300mm centres to either
side of 48mm studs (0.5mm thick having one flange of 34mm and another flange of 36mm
made of G. I. Steel) placed at 610mm centres in 50mm floor and ceiling channel (0.5mm
thick having equal flanges of 32mm made of G. I. Steel) with joints staggered to avoid
through joints.A fixing channel of 99mm width (0.9mm thick having two flanges of 9.5mm
each) has to be provided at the horizontal 600 mm C/C Finally partition is finished with 1mm
laminate on both side.All exposed wooden members to be finished in PU polish, in approved
shade and pattern to match with partition or as as per instruction. The measurement will be
taken up to false ceiling level only
2 Same as above Item no D 1 but finished on one side Veneer & other Ply SQM 83 -Rs.
3 Same as above Item no D 1 but finished on both side only Ply SQM 18 -Rs.
4 Glazed Partitions: (Toughened with SS frame) 6mm thk SQM 142 -Rs.
Supply & Installation of Full Height Partitions systems of 45 mm x 25 mm thick Anodised
Alumimum Alloy section on all four sides for the partitions using JEB 834 or equivalent & JEB
016 or equivalent as verticals at the solid partition junction & Horizontals at top & JEB 019 &
JEB 020 or equivalen at bottom with snap on option for installing glass & 'T' Section, corner
Section & Vertical "I" Section between Glass to glass from FFL up to 2700mm. Rate include
supply & Installation of 10 mm thk toughened glass with double sided adhesive tapes for
glass to glass butt joints. All the material/arrangement (MS section etc.) required for fixing
the partition to ceiling is inluded in the cost.
Make: JEB, DORMAKABA
5 Extra for providing bend/curve glass of appx radius 3m, with similar specifications as in item
above
SQM 12 -Rs.
6 Providing & fixing glass wool 50mm thick for insulation SQM 340 -Rs.
Page 7
S.NO DESCRIPTION UNITS QTY RATE AMOUNT7 Providing & fixing in Partitions, smart glass made from extra clear glass with a sandwich
interlayer of Special Polymer film that can be activated to turn transluscent with an electric
switch, including remote control device.
SQM 5 -Rs.
E DOOR
1 12mm thk toughened glass door
Supply & Installation of Single leaf JEB Wideline door frame or equivalent formed out of
Anodised Alumimum Alloy section 45 mm x 25mm JEB 834, JEB 016, JEB 011A or equivalent
as door Jamb & JEB 046 & JEB 046C or equivalent as door rebate & Single leaf JEB Stile
Wideline or equivalent door shutter 75 x 45mm Thk sections using JEB 423 at Vertical & JEB
425 & JEB 428 as Horizontal or equivalent at Top & bottom with 4Nos of Hinge/WL & Single
Leaf glazed Door of 10mm Toughened glass with DORMA Hardware like Exposed Door closer
TS 90 with Hold Open, Narrow stile mortize lock with 35mm backset & lever handle with
Oval roses, 70mm EPC with one side key & one side thumb turn indicator, Drop Down Seal &
Half moon door stopper etc.,complete. All the material/arrangement (MS section etc.)
required for fixing the partition to ceiling is inluded in the cost.
1.150 x 2.7 m NOS 3 -Rs.
Make: JEB, DORMAKABA
2 Solid wooden door ( Veneer )
Providing & fixing Teak wood frame of size 50x75mm including making rebate for
shutters,with 38 mm thick flush door including finishing with1 mm laminate both sides,
including HAFFLE, HETTICH, Dormakaba hardware cylindrical knob and handle lock and,
stopper , tower bolt, door closures etc. complete of SS approved quality . All exposed
wooden members to be finished in PU polish, in approved shade and pattern to match with
partition or as as per instruction.
i 1.2 x 2.7 NOS 10 -Rs.
ii 1.15x 2.7 NOS 4 -Rs.
iii 1.8 x 2.7 NOS 1 -Rs.
F PANELLING
Page 8
S.NO DESCRIPTION UNITS QTY RATE AMOUNT
1 Providing & fixing Panelling consisting of:
Frame work with 45 x 25 mm GI sections @ 600 mm c/c in both directions
1.1a Facing with 9 mm thick Premium quality BWR gurgen base Premium quality BWR gurgen
baseply wood well secured to frame work by means of screws and nails.
Sqm 250 -Rs.
b Finishing with 4.0 mm thick Veneer with grooves as per drawing and design.
c Finishing all wood surfaces with PU polish as per standard practices and specification
complete.
d fixing post formed Veneer skirting 80mm high with Araldite adhesive
1.1b Facing with 12.5mm thk MDF board fixing on frame by means of screws and nails Sqm 15 -Rs.
c fixing 4mm thick lacquered glass with adhesive etc. with 4mm grooves as per design and
complete to the satisfaction of Architect / Bank's Engineer.
Make : Saint Gobin, Asahi, Modiguard
2 Column Panelling
Providing & fixing Panelling consisting of:
i Frame work with 45 x 25 mm GI sections @ 600 mm c/c in both directions
a Facing with 9 mm thick Premium quality BWR gurgen base ply wood well secured to frame
work by means of screws and nails.
Sqm 125 -Rs.
b Finishing with 4.0 mm thick Veneer with grooves as per drawing and design.
c Finishing all wood surfaces with PU polish as per standard practices and specification
complete.
d fixing post formed Veneer skirting 80mm high with Araldite adhesive
ii CORIAN Jali
Page 9
S.NO DESCRIPTION UNITS QTY RATE AMOUNTProviding & fabricating and installing Jali work panels made of 12 mm thick "CORIAN" solid
acrylic surface, with laser cutting, buffing, finishing edges etc complete. Jali panels to be
fixed to the floor and ceiling . ,complete as per the detailed dwg or the instructions of the
Architects. Cost also to include Design /shop drawings , and all necessary supports for
installations. . Mode of measurement : Length & height of the Jali Work Panels.
Sqm 42 -Rs.
3 Providing and supplying Acoustical Wall Paneling’ with square edges made of fibre glass
substrate 25mm thick and wrapped on the front side with an acoustically transparent and
classified for Fire reaction Class A, as per ASTM E-84, fabric with an option of colors – Husk,
Copper, Sangria, Sesame, Coffee, Charcoal, Titanium, Flame, Peanut and Shell as per the
choice of the Architect of size 600x600mm, 600x1200mm & 600x1800mm providing a
minimum sound absorption level of 0.85 NRC to be affixed to wall using Wall panel Impalers
supplied by Armstrong Ceiling Solutions and construction adhesives as per the instructions
laid down by the manufacturer.
Sqm 57 -Rs.
Armstrong ‘Optra" or equivalent
INSTALLATION:
In order to fix the panels to the wall, the Impalers shall be fixed to the wall surface using self
tapping screws. 3 nos. in case of 600x600mm, 4 nos in case of 600x1200mm and 5 nos in
case of 600x1800mm wall panel Impalers to be used for the installation purpose. Silica based
construction adhesive to be dabbed on to the projecting elements (spikes) of the impalers.
Wall panels shall be pierced through the spikes of the impalers ensuring the line and level of
the panels are maintained.
Page 10
S.NO DESCRIPTION UNITS QTY RATE AMOUNT4 Providing and Fixing Armstrong Channeled Woodworks or equivalent, perforated panels of
width 192mm, thickness of 15mm and length 2400 mm or as required by the Architect/
approving engineer, made of a Moisture resistant fibre board with minimum 595 Kg/M3
density substrate with a laminated facing as per the approved shade & finish and a
melamine balancing layer on the reverse side. The boards shall have a special perforation
pattern where the visible surface has a “Helmholtz” fluted perforation of 3mm width and
5mm of visible panel each. The edges of the panels shall be “tongue-and-grooved” to receive
special clips for installation. The back of the perforated panel shall have sound absorbing
non-woven acoustical fleece having NRC of 0.65. The panels shall be mounted on special
aluminium splines (keel) using clips provided by Armstrong and approved by the Architect/
Engineer-in-Charge.
Sqm 38 -Rs.
INSTALLATION: To comprise main runner spaced at 600mm centers securely fixed to the
structural soffit using Armstrong suspension system (specifications below) at 1200mm
maximum center. The First/Last Armstrong suspension system at the end of each main
runner should not be greater than 450mm from the adjacent wall.
Flush fitting 600mm long cross tees to be interlocked between main runners at 1200mm
centre to form 1200 x 600 mm module.
Perimeter trim to be Armstrong wall angles of size 3000x19x19mm, secured to walls at 450
mm maximum centers.
5 Wall paper SQM 47 -Rs.
Providing & fixing of wall paper of basic rate Rs1700/sm, of approved shade, pattern,and
make as per drawings / instructions, fixed to ply with adhesive.
6 Leather panelling SQM 12 -Rs.
1.1a providing and fixing in wall panelling , 1.5 mm thick recycled bonded leather withnatural
latex. Panels to be in approved shades , texture and sizes. Leather panels to be fixed to 19
mm thick premium quality BWR gurgen base board pasted from the reverse to give a
smooth finish surface ply wood well secured to frame work by means of screws and nails.
Page 11
S.NO DESCRIPTION UNITS QTY RATE AMOUNTb Finishing with Leather with grooves as per drawing and design.
7 Italian cladding SQM 140 -Rs.
Providing and fixing polished italian marble (Perlato Sicillia) or wall cladding with hite
adhesive PG 400 of ASIAN or equivalent.The marble stone slabs laid over under-bed, pressed
and tapped down with wooden mallet to the proper level, lifted and pressed again with
adhesive spread over the surface with fine joint finished including pigments, curing, grinding,
making corners, and finished with diamond polishing etc. all complete as per drawings,
specifications, manufacturer's recommendations, as per pattern in drawing. (Basic rate Rs.
3300/sm)Item to include diamond polishing to marble.
G STORAGES
Providing and fixing Storage of 450mm depth made with 18 mm Premium quality BWR
gurgen basegrade plywood. The external surfaces of plywood to have 4mm Veneer finish
and inside with 1mm thk laminate. Rate to include 18 mm thick post formed Veneer skirting
80 mm high, and all SS hardware of HETTICH,HAFFLE, DormaKaba good quality SS hinges,
handles, multipurpose lock etc. all complete. All exposed edges of plywood to be lipped with
6mm / 4mm TW lipping with PU polish
1 750 mm high. SQM 10 -Rs.
2 2100 mm high. SQM 14 -Rs.
H MISCELLANEOUS WORKS
1 Texture paint SQM 82 -Rs.
Providing and applying Stucco Marble finish, non toxic, non flammable of approved finish &
shade. Rate are inclusive of sanding / cement premier putty and finished with three coats of
Stucco Marble finish with trowel / scrapper. Basic cost Rs 475 per sqm .
2 Platic Emulsion paint SQM 50 -Rs.
Page 12
S.NO DESCRIPTION UNITS QTY RATE AMOUNTSupply and application of washable interior grade Dulux 3-in-1 pastic emulsion paint on
walls with 1 coat of wallprimer and 2 or more coats of plastic emulsion paint as per
manufacturer's specifications etc. all complete. All painting final coats to be done after
removal of face plates of switch boards in coordination with the electrical contractor and
face plates to be fixed only after satisfactory completion of painting. (basic rate Rs200/sm)
Page 13
S.NO DESCRIPTION UNITS QTY RATE AMOUNT3 Roller Blind SQM 80 -Rs.
Supplying fitting and fixing Roller Blind with 100% Polyester fabric (plain/ ribbed fabric of
approved colour and shade). Nominal thickness of fabric shall be 0.60-0.80 mm and nominal
weight 255 - 450 grams per square metre, hanging excellent hanging properties and very
high tearing strength, Coating of the fabric shall be of Acrylic, which shall be resistant to
cracking and fraying. The fabric shall be suspended from the top channel made of extruded
anodised alloy of 1.25-2.00 mm nominal thickness and 38 mm nominal diameter. The top
channel shall be fixed with powder coated mild steel brackets with clutch assembly on either
end of blind, fixed to jambs of the window opening with 50 mm stainless steel screws with
heavy duty PVC wall (RAWL) plugs.
The operating mechanism fixed to the top channel shall be made of high strength ABS plastic
having ultra-smooth gear with spring booster of high carbon steel. The mechanism shall be
operated with tilt chain having 4.50 mm balls made of ABS plastic linked with 1.50 -2.00 mm
polyester chord. The mechanism shall allow the blind to stop in desired position with the
help of stop lock. The bottom channels shall be of aluminium tube of 21 mm nominal
diameter and 1.50-2.00 mm nominal thickness. The fabric shall be enclosed in suitably
created pocket along the tubes, which shall be closed from side with end caps of same
colour to the bottom roller. All exposed components of the roller blind shall be of milky
white colour. (Basic rate Rs1500/sm)
Make : Vista levelor, hunter douglas
4 Dismantling all types existing partitions, walls, false ceiling, wall panelling, A.C.P. Sheet
paneling, Floor Tiles , RCC, etc. work as per instruction of bank engineer/ architect & make
new surface same as per existing condition. stacking the usable material to the site
instructed by the Bank, and disposal of debris /unserviceable material dumping outside
the municipal limit.
LS -Rs.
5 Providing and fixing Glass film as per design of 3M make. SQM 80 -Rs.
Page 14
S.NO DESCRIPTION UNITS QTY RATE AMOUNT
INTERIOR WORKS (A)
PLUMBING WORKS
1 Providing and fixing of white vitreous china wall mounting type European water closet
with the followings complete with all accessories. Including cutting the walls & R.C.C floor
slabs making good the same complete as required.
a C.P. bolts and nuts
b C.I. chair, or other hanging arrangements by Fischer / Hilti
c Bakelite toilet seat and cover
Model no : REPLAY, K-6098IN-SR-0 (wall mounted Closet )
Make : Kohler or equivalent
Water closet as described above NOS 4 0
2 Providing, fixing, testing & commissioning of concealed type dual flushing cistern of with
adjustment of 3 - 4.5 litres with the following complete. The flush pipe shall be concealed in
wall and connected to the WC with required fittings. Cutting the wall and making good same
complete as required
a Flush actuator facia assembly including brass / SS screws
b Bush and washer
c Heavy class flush pipe upto cistern including connection to WC
d Angle valve with flexible connection.
Model no : RAPID SL
Make :Grohe or equivalent
Flushing cistern as described above NOS 4 0
3 Providing and fixing Grohe Skate Cosmopolitan Flush Plate (Chrome) with the following
complete as required. NOS 4 0
Page 15
S.NO DESCRIPTION UNITS QTY RATE AMOUNT4 Providing and fixing CP Brass Rinsing spray with the following complete as required.
a Regulated of approved quality
b 1.5m long plastic NBR braided pipe
c Flexible pipe
d Wall hooked
e C.P. Brass angle valve NOS 4 0
Model no: ALD-CHR-565
Make : Jaguar or equivalent
CP Brass Rinsing spray as described above
4 Providing and fixing in position of white vitreous china counter Topwash basin with
following complete including cutting and making good the walls floors complete as required.
a C.I. bracket painted white
b 32mm dia C.P. brass waste
c C.P. brass chain with rubber plug
d 32 mm dia C.P. brass bottle trap with extension piece
e Wall flanges and rubber adapters for waste connection
Model no : FOREFRONT 900MM W/O DECK, K-75375IN-0
Make : Kohler or equivalent
wash basin as described above NOS 4 0
5 Providing & fixing C.P brass long neck pillar cock with aerator. NOS 4 0
Model no : KUBIX PRIME - Single Lever Tall Boy, PRODUCT CODE: KUP-CHR-35005BPM
Make : Jaquar or equivalent
Page 16
S.NO DESCRIPTION UNITS QTY RATE AMOUNT6 Providing and fixing in position of white viterous china large flat back urinal
supported by CI/MS bracket including C.P. brass waste with dome type grating, C.P.cast brass
bottle trap with extension piece,wall flanges complete as required.
NOS 4 0
7 Providing and fixing electrically operated (wall burial type) automatic urinal flushing systems
for urinal, flushing only when in use, comprising of following complete as required
(witbout any provision required in false ceiling and shaft for solenoid valve).
a Plumbing, electronic and electrical items
b C.P. brass flush pipe with clamps and screw
c C.P. brass elbow
d C.P. brass spreader
e C.P. wall flange
f Infra red photo cells
g solenoid valve
Model no : PATIO TOUCHLESS URINAL, WATERSAVING, K-16321T-M-0
Make : Kohler or equivalent
Automatic urinal flushing system as described above NOS 4 0
9 Providing & fixing Toilet accessories:
a) C.P. brass towel rail with C.P. brass wall brackets & C.P brass screws complete as required.
i) . Size 600 x 20 mm size NOS 4 0
b) Recessed type S.S. toilet paper holder NOS 4 0
Model no : F840008 Paper Holder
Make : Hindware or equivalent
c) Push button type liquid soap dispenser NOS 4 0
Make: SDR-WHT-DJ0010F - Jaguar or equivalent
Page 17
S.NO DESCRIPTION UNITS QTY RATE AMOUNT
d) Paper dispenser NOS 4 0
Make: EP01 S.Steel Paper Towel Dispenser- EURONIC
e) C.P. brass twin coat hook. NOS 4 0
f) 15 mm dia C.P. brass bib cock (long body) & C.P. brass wall flange of approved quality:
NOS 4 0
g) C.P. brass angle valve with the following complete as required.
i) Filter
ii) C.P. brass flow regulator (flow 8 LPM)
iii) C.P. wall flange
iv) Nut and washer
Angle valve as described above NOS 12 0
h) C.P Copper connection 375 mm long including nuts and washers and making connection to
fixtures and fittings complete as required. NOS 8 0
10 Providing and fixing Hand Dryer Nos 4 0
Make: Euronics Automatic Hand Dryer EH22ABS
Page 18
S.NO DESCRIPTION UNITS QTY RATE AMOUNT11 Providing, fixing, jointing, testing and commissioning spun/centri C.I. pipe for soil,
waste & vent pipes installation conforming to IS:3989 cut to required lengths including
all necessary fittings and specials such as Bends, junctions, offsets, cleanouts, access pieces
(plain or door) & vent cowl. Fixing at wall/ceiling level supported by MS GI angle, chanel,
clamps & hangers etc. Making connection with drip seal joint of required depth as
per BIS / manufacturer. Cutting, chases/holes in floors / walls / slab and And G.I. Heavy class
pipe sleeve of one size larger diameter shall be provided wherever the pipes are crossing the
fire rated walls / floors ,slab and sealing the sleeves with glass wool in between and fire
sealent compound at either ends, all as per Project Manager’s / Consultant requirement. The
item include cutting hole in wall, floor,slab and making good the same with required
material.
a) 100mm dia RM 5 0
12 Providing and laying 1:2:4 cement conc. all round the pipe including bed concrete for the
following C.I. pipes and specials below floor including necessary shuttering etc. complete as
required and steel reinforcement if required.
a For 100 mm dia pipe, 100mm thick alround and 100 thick bed concrete RM 2 0
13 Providing & fixing in position CI full bore "P"/ "S" trap (IS:3989). Making proper connection
with drip seal. Cutting chase / hole in floors /slabs and making good the same after placing
the trap complete as required. The trap shall have minimum 50mm deep water seal and shall
be supported by GI clamps hanger as per Consultant.
a 100 mm inlet and 100 mm outlet. NOS 8 0
Page 19
S.NO DESCRIPTION UNITS QTY RATE AMOUNT14 Providing and fixing G.I. inlet hopper with required inlets fittings to receive waste pipes from
fixtures waste. The hopper shall be fabricated from 100 mm dia upto 450 mm long G.I. heavy
class pipe with welded G.I. sockets and supported through galvanized steel from slab or set
in cement concrete mix 1:2:4 complete as required. The hopper shall be hot dip galvanized
after fabrication and fixed to CI trap with drip seal (Cost shall be inclusive of providing 100
mm dia GI clean out plug for maintenance purpose
NOS 8 0
15 Providing & fixing 100mm x 65mm dia G.I. waste made from G.I. elbow and extension piece
upto the grating, including cutting chases, the floor / slab complete as required and making
connection to waste pipe. NOS 4 0
16 Providing and fixing S.S. grating with Mosquito proof S.S. strainer (cockroach trap) inlcuidng
setting in floor with cement mortor to match with floor finish. NOS 4 0
17 Providing and fixing in position G.I. heavy class pipe and fittings conforming to IS:1239
(for waste pipe from individual fixtures to floor trap & vent pipe) Including fixing at wall /
ceiling level supported by galvanised clamps and hangers etc. Cutting holes in
wall/floors/slabs and making good the same with cement concrete 1:2:4 complete as
required.
a 32 mm dia RM 4 0
b 40 mm dia RM 6 0
c 50 mm dia RM 2 0
d 65 mm dia RM 6 0
18 Making, cutting & chasing in walls / floor, upto 50 mm dia waste pipes & fittings. Making
good the same by using 1:1 Cement mortar. RM 10 0
19 Providing two coats of synthetic enamel paint of approved shade as per pipe colour code
over a coat of primer for G.I. waste & Vent pipe & fittings complete as required
a 32 to 50 mm dia RM 18 0
Page 20
S.NO DESCRIPTION UNITS QTY RATE AMOUNT20 Providing protection to G.I. pipes & fittings (running in wall chases / embedded areas) by
wrapping two layers of 400 microne polythene sheet over two coats of bitumen paint
inlcuding proper overlaps on the joints complete as required.
a) 32 mm dia to 50 mm dia RM 18 0
21 Providing and fixing Brass clean out plug with S.S. screw, GI heavy class pipe and socket
jointing with lead caulking / drip seal to CI pipes or class LA pipes complete as required
a For 100mm dia pipe NOS 4 0
22 Providing and fixing P.V.C. WC connector (straight or bend type) with rubber lip ring.
Including 110 mm dia PVC pipe of required length and making connection to C.I. pipe
complete as required. NOS 4 0
23 Painting of exposed C.I. pipes and fittings (after installation) with two coats of
synthetic enamel paint of approved shade as per pipe colour code including painting of
legends with direction arrows.
a 100 mm dia RM 4 0
24 Providing and fixing CPVC (Chlorinated Poly Vinyl Chloride) water supply pipes as per CTS SDR
- 11 at a working pressure of 28 kg/sqcm at 23 deg C and 7 kg/sqcm at 82 deg C, for jointing,
using solvent welded CPVC fittings i.e. Tees, Elbows, Couplers, Unions, Reducers, brushings
etc. including transition fittings connection between CPVC & metal pipe/GI) i.e. Brass
Adaptors (both Male & Female threaded) conforming to ASTM D-2846 with only CPVC
solvent cement conforming to ASTM F-493. All termination points for installation of faucets
shall have brass termination fittings with galvanised angles, channels, clamp, hangers etc, as
per specification. The item include cutting hole in wall, floor, slab and making good the same
with required material.
a 15 mm dia (Sche.80, working pr. 21.1kg/sqcm) RM 10 0
b 20 mm dia(Sche.80, working pr. 21.1kg/sqcm) RM 6 0
Page 21
S.NO DESCRIPTION UNITS QTY RATE AMOUNT
25 Providing and fixing CPVC valves suitable for working pressure of 10 Kg / Sqcm. including
flanges / union, etc. complete as required.
a 20 mm dia NOS 6 0
26 Making 7.5 x 7.5 cm chasing in wall and floors with cutter for PVC pipes and fittings & making
good the same by using 1:1 cement mortar over the wire mesh (Chases will be measured
along the centre line of the installed pipe). RM 16 0
27 Providing & fixing closed cell thermal insulation tubes 6mm thick to hot water pipe and
fittings.
Over 15 mm dia. Pipe RM 10 0
28 Fixing only Instant type electric hot water heater made out of heavy gauge steel jacket
finished with rust proof baked-on glossy white enamel paint, inside glass lined heavy gauge
copper tank, 25 mm thick polyurethane foam insulation, thermostatically controlled
immersion heater with pilot neon lamp, replaceable magnesium anode bar, suitable for 8.0
bar maximum working pressure, cold water inlet and hot water outlet pipe, suitable length
of electrical cable and 15 amp 3 pin plug top, complete in all respect including testing etc.
(Horizontal/Vertical)
3 ltr Capacity. Instant water heater Each 4 0
29 Providing and fixing stainless steel grating with rim of approved design including setting in
floor with cement mortar. (For Floor Trap/Floor Drain)
125 mm dia Each 4 0
Total plumbing works (B) 0
Total RENOVATION WORK (A+B) 0
GST Extra
Page 22