INTELLICAM SYSTEM LL USER’S MANUAL REVISION 6

Page 1

INTELLICAM SYSTEM LL USER’S MANUAL REVISION 6.0

-IR900/901 PASSIVE INFARED SENSORS

-RX930 RECEIVER/PROCESSOR

-SYSTEM I MINI-CAM SURVEILLANCE KIT (GEN III)

-SYSTEM II GROUNDHOG® SURVEILLANCE KIT (GEN III)

©COPYRIGHT 2011 IntelliCam, LLC All Rights Reserved

While every effort has been made to insure the accuracy of all information in this document, IntelliCam, LLC assumes no liability to any party for any loss or damage caused by errors or omissions or by statements of any kind

in this document and its updates whether such errors are omissions or statements resulting from negligence, accident, or any other cause. IntelliCam, LLC further assumes no liability arising out of the application or use of any

information, product, or system described herein, nor any liability for incidental or consequential damages arising

from the use of this document or products. IntelliCam, LLC disclaims all warranties regarding the information contained herein, whether expressed, implied, or statutory, including warranties of merchantability or fitness for a

particular purpose. IntelliCam, LLC makes no representation that the interconnection of products in the manner described herein will not infringe on existing or future patent rights, nor do the descriptions contained herein imply

the granting or license to make, use, or sell equipment constructed in accordance with this description.

Further, information and descriptions contained herein are the property of IntelliCam, LLC Such information

and descriptions may not be copied, disseminated, or distributed without the express written consent of IntelliCam, LLC This manual is for informational purposes only. All information contained within is subject to change without

notice.

*****WARNING*****

The IR900 Sensor and RX930 Receiver/Processor are surveillance devices, to be used for intelligence

gathering purposes only, and were NOT DESIGNED or INTENDED for the PROTECTION OF LIFE OR PROPERTY. Like all electronic devices, they may fail at any particular moment.

*****WARNING*****

Recording of voice is UNLAWFUL under most circumstances. Consult with an attorney before attempting to do so; otherwise you could be prosecuted for Title 6 or 8 violations.

IntelliCam, LLC 11138 Air Park Road, Suite H – Ashland, VA 23005

Phone: (804) 798-1004 Email: [email protected]

Trademarks: Palm Pilot is a trademark of 3COM; MiniDV is a trademark of SONY. Sensor iCam, Mini-Cam and Chameleon are trademarks of IntelliCam, LLC.

Groundhog® is a registered trademark of IntelliCam, LLC

Page 2

TABLE OF CONTENTS

1.0 INTRODUCTION

2.0 SENSOR CONTROLS AND INDICATORS

2.1 Power Jack 2.2 Program/Reset Button

2.3 Red Light 2.4 Antenna

2.5 Lens

3.0 SENSOR RANGE TESTING

4.0 SENSOR WALK TESTING

5.0 SENSOR PROGRAMMING

5.1 Sensor Normal Programming

5.2 Sensor Extended Programming

6.0 USING PASSIVE IR SENSORS 6.1 Infrared Signal

6.2 Infrared Noise

7.0 RX930 RECEIVER CONTROLS AND INDICATORS

7.1 Power/Data Jack 7.2 Program Button

7.3 Computer Reset Button 7.4 Red Light

7.5 Antenna

8.0 RX930 RECEIVER PROGRAMMING

8.1 Alarm Logic 8.2 Timers

8.3 ID

8.4 Output

9.0 MINI-CAM SYSTEM SETUP

10.0 TECHNICAL INFORMATION

12.1 Sensor Specifications

12.2 Receiver/Processor Specifications

11.0 RF INTERFERENCE

Page 3

1.0 INTRODUCTION

The IR901 Passive Infrared Sensor and the RX930 Receiver/Processor make the System I the smallest,

lightest, and most advanced video surveillance system on the market today. Integrating the RX930 Receiver/Processor into the control enclosure, the Generation III design simplifies the user interface and allows for a

smaller, more compact concealment. Generation III can also be expanded into a multi-camera system with the

optional VSM-1 Video Switcher Module and a wide selection of cameras give you telephoto capability or low light imaging for nighttime use. Targets may be screened for size, speed, direction, dwell and material composition before

initiating video. Video is captured on a high quality digital video recorder only when suspicious activity is present.

A multitude of sensors, such as Passive Infrared, Seismic, Magnetic, and Motion Activated are available for your

precise sensing requirements. All of them incorporate IntelliCam’s exclusive Chameleon™ Technology software, which allows the sensors to become “smart sensors” by adapting to the environment in which they are placed. By

automatically adjusting the sensitivity according to the level of thermal, seismic, or magnetic back ground “noise”,

Chameleon™ Technology sets the optimal trigger threshold for the environmental conditions. This prevents unwanted false alarms from depleting the batteries and wasting valuable videotape. For additional security, Sensor

“A” and “B” is also possible which requires 2 sensors to trigger within a 10 second window before an alarm is processed.

Gen III Groundhog® Digital MiniCam Video Surveillance System I

The System I is shipped with our most versatile sensor, the IR901 Passive Infrared Sensor. The IR901

detects thermal energy (people, vehicles, etc.), which are in motion. It has a detection range of 50 feet with a wide field of view (20 feet @ 50 ft. distance). The device is about the size of a shotgun shell (2.8” long x 1.0” diam.) and

can be mounted on a tree for optimal RF range or hidden in ground cover (sticks, branches, etc.) for optimal

concealment. It uses 2 lithium watch batteries for a power source and can remain outdoors for 2 - 3 weeks, in any climate from hot to cold. Other versions of the IR901 are available that have an external battery pack (IR901B) and

can remain in the field for up to 6 months. For extended sensing range, the IR900 is a long range version of the IR901. It can detect people up to 200 feet and vehicles up to 400 feet.

IntelliCam also manufactures Seismic (SA900M), Magnetic (MG900), and Motion Activated (MB900) sensors. The SA900 Seismic sensor detects footsteps up to 100 feet away and vehicles 1000 feet distant. It has several

detection modes including footstep only, which allows it to be used in a rural environment near a road.

The Digital System I (also known as a Groundhog®)

Powered by 8 “AA” batteries

This system uses a micro digital recorder

Armored cables prevent rodent damage

A low light color camera allows video in dawn & dusk scenarios

Always fasten lid securely – Do not submerse in water

If buried, cover case with plastic or other protective barrier

Page 4

The MG900 Magnetic sensor detects metal objects such as vehicles up to 8 feet from the roadway. Both the

SA900M and the MG900 can remain active for up to 6 months on 4 “AA” alkaline batteries. The MB900 detects motion and can be taped underneath of a cash drawer or valuable property. When some opens the drawer or

removes the property, an alarm triggers the System I.

2.0 SENSOR CONTROLS AND INDICATORS

2.1 Power Jack

The IR901’s batteries are self-contained. Slide the rubber boot off the back of the sensor and insert the 2 CR1225 Lithium Batteries. These should power the IR901 for 2-3 weeks. When not using the sensor, you can

disconnect the power by slipping a small piece of plastic between the + lead and the top battery. The batteries are

exhausted when the Red Light continues to cycle ON/OFF.

The IR901B version uses a 6 volt external battery pack. Attach the power adaptor to the IR901B’s connector. Four alkaline “AAA” batteries will power the IR901B for about 4-6 months. Power can be turned off by

removing the power cable from the IR901B.

2.2 Program/Reset Button

The IR901 and the IR901B use an internal magnetic switch for programming and control. A Magnetic Wand

activates the switch when it is placed near the Red Light. The switches “hot spot” is slightly behind the Red Light and is marked with a dot. Programming is accomplished by moving the Wand into and away from the hot spot

quickly. (see 5.0 Sensor Programming).

2.3 Red Light

The Red Light is used for programming and as an alarm indicator. It only illuminates when an alarm occurs

during the RangeTest/WalkTest period (2 minutes) and automatically turns off after 10 minutes for covert reasons.

6V “AAA” Battery Box

Adaptor

Antenna

+

2, CR1225 Lens Lens

3 volt Lithium Batteries

Connector Red Light = Alarm LED

Blue Dot = Programming “Hot Spot” for Magnetic Wand

Passive Infrared Sensor

IR901 Passive Infrared Sensor IR901B Passive Infrared Sensor

Page 5

Figure 2

2.4 Antenna

The flexible antenna allows for UHF propagation of the RF signal. The antenna must be oriented in a vertical

direction for best RF propagation and for proper alignment of the Infrared Beams.

2.5 Lens

The IR901’s focal length is preset to detect a person at an optimum distance of 30 feet, although it will work

satisfactorily over a range of 5 to 50 feet. Its field of view is about 10 feet wide at a distance of 50 feet. The lens is aimed in the direction of your target area.

The IR900 is a long-range version of the IR901. Its focal length is preset to detect a person at an optimum distance of 100 feet, although it will work satisfactorily over a range from 20 to 200 feet. The field of view at 100

feet is about 5 feet wide, allowing for very precise control over the sensing region.

3.0 SENSOR RANGE TESTING

1. The IR901/900 Sensors may be monitored by several methods. One is to simply program the frequency

of the Sensors into a scanner (916.5 MHz, AM mode). Another method would be to use an RX916/920 Receiver Processor or a WPSU-1 Wireless Power Switching Unit. Both theses devices are options and must be purchased

separately but have the advantages of mobility and small size. The other option is to use the RX930 Camera enclosure, which has the audio beeper built into the box. This can either be carried while range testing or can be

places near the target area on the ground, in which case the operator can open the lid and hear the tones. There is

nothing the operator has to do to the RX930 module except apply power from the battery pack. The tone beeper will alert the operator of sensor alarms for 10 minutes after power is applied. After 10 minutes the tones will go

silent, in which case the operator must reset the RX930 (by pushing the black program button until the RED light comes on) if continued monitoring is desired.

2. Screw the Sensor Tree Mount into the tree, about 1 to 3 meters from the ground level. It is best to locate the RX930 receiver on the same side of the tree as the Sensor so that the tree will not block the RF signal.

Best range is achieved with line-of-sight conditions, that is, with nothing coming in between the Sensor and Receiver. Attach IR900/901 Sensor to tree mount with the antenna vertical. Aim the Sensor at the target area.

Attach the Battery Pack Adaptor to the IR900 and Velcro battery to the tree mount. To activate the IR901, remove the plastic insulator from the batteries. As soon as power is applied, the Red Light should come on and go off. After

about a 30 second stabilization period, the Sensor should be ready for the Range Test. Trip the Sensor by slowly

waving your hand in front of the lens.

3. When the Sensor trips, it will start transmitting at 1-second intervals with the Red Light flashing. Walk away from the Sensor with the RX930 enclosure in your hand. The maximum range will be found when the beeps

stop or become erratic. You should cut this distance in half for a more reliable setup; however, operation at UHF

frequencies cannot be predicted with any great certainty due to absorption and reflections from nearby objects. The Range Test should involve your hanging the RX930 antenna in a suitable bush or tree, with appropriate camouflage,

and standing back from it. If the beeps become erratic then you know that the distance/setup is marginal. Generally, if distances are kept below 100 feet, there should be little problem with the setup. Factors that degrade

the RF performance will be thick vegetation, buildings or metal objects. For Long Range Applications, repeaters are

available that will send the alarm signal up to several miles if so desired.

4. Range Test can be repeated if desired by moving the Programming Wand into the Sensor’s “hot spot” and holding it there until the Red Light comes on. After the Red Light comes on, immediately move the

Page 6

Programming Wand away. Wait for several seconds and trip the Sensor with your hand. Follow step 3 above after

Sensor trips. Range Test will normally last for about 2 minutes. It can be aborted at any time by momentarily touching the hot spot with the Magnetic Wand.

4.0 SENSOR WALKTEST

1. Follow steps 1 and 2 of Range Test.

2. When the Sensor trips (indicated by flashing Red Light), abort the Range Test Mode by sweeping the magnetic “hot spot” with the magnetic wand. The light should stop flashing. The Sensor is now in its Default Mode

with Sensor ID=3 and Sensitivity=Full Auto and is ready for the Walk Test. (Alternately, you can program the

Sensor ID and Sensitivity prior to Walk Test. See Sensor Programming).

3. With the Sensor aimed at the target area, walk back and forth in a rapid fashion where the sensor is aimed. The Sensor’s Red Light will flash and an alarm will be transmitted to the Receiver when the Sensor’s Infrared

Beams are crossed.

The Receiver’s Red Light will flash simultaneous to it beeping when it receives the sensor’s alarm. (The Red

Light from the Sensor and Receiver will glow only for the first 10 minutes. After 10 minutes, it no longer comes on, for covert reasons. To reactivate the Red Light on both devices, simply sweep the sensor’s magnetic hot spot or

press the RX930’s Program Button momentarily.)

The Sensor takes 4-6 seconds to reset after an alarm is transmitted, so pause briefly before attempting to

re-enter the Sensor’s field-of-view. After you have located the Sensor’s beams with the Walk Test method, walk at a slower pace to insure that detection will be reliable. Before you complete the Walk Test, you can hook up the RX930

to the Palm Programmer for a read-out of the alarm record. This is done by plugging the Palm Pilot stereo cable into the stereo receptacle on the Battery box. Details of the Alarm, such as Sensor ID, Receiver ID, Target Size Factor,

Description, Velocity, and “Signature” are displayed for each alarm. These variables can be programmed in the

RX930 Receiver’s memory to selectively alarm when certain conditions are met.

5.0 SENSOR PROGRAMMING

The IR900/901 Passive Infrared Sensors can be programmed with a Sensor ID and a Sensitivity Level, or it

can be used in the Default Mode, where the Sensor ID = 3 and the Sensitivity is set to Fully Automatic. The Default Mode is the simplest to use, requires no programming input, and comes up automatically after power is applied and

the Range Test is completed. Full Auto Sensitivity is recommended for most applications, particularly when the ambient temperature changes considerable during the day, in which case the IR900/901 will automatically adjust the

sensitivity for the best Signal (target) to Noise (background) ratio.

If programming is desired, enter the Sensor ID followed by the Sensitivity. The Sensor ID tells the RX900

Receiver which Sensor went into alarm. The Sensitivity determines how far away the Sensor will sense a target.

5.1 Sensor Programming

1. Move the magnetic wand into the Sensor’s “Hot Spot” and hold it there until the Red Light comes on.

2. After the Red Light comes on, immediately move the Wand back and forth into the hot spot to enter the

Sensor ID number. The Red Light flashes each time the Sensor ID is incremented. After the Sensor ID is entered, the IR900/901 will “play back” the number you entered so that it may be verified as being

correct (Refer to the Sensor ID Table). If no entry is made for Sensor ID, the Sensor enters the Range Test Mode (see Range Test).

Page 7

3. Following playback of Sensor ID, the Red Light will stop flashing and go steady to prompt you for the 2nd variable, Sensitivity.

4. Enter the Sensitivity in the same way that the Sensor ID was entered. A higher Sensitivity will mean that the IR900/901 can detect targets at a greater distance (Refer to the Sensitivity ID Table). If no

entry is made for Sensitivity, the Full Auto mode is selected.

Sensor ID Table

Press Button Value Sensor ID Description

0

ID3

No entry=Default Mode. The Sensor enters the Range Test Mode. After Range Test, Sensor ID=3 and Sensitivity=Full Auto Mode.

1

ID1

Normal Mode. Sensor ID set to value 1. Walk test will beep once.

2 ID2 Normal Mode. Sensor ID set to value 2. Walk test will beep twice.

3 ID3 Normal Mode. Sensor ID set to value 3. Walk test will beep three times.

.

.

.

9

ID9

Normal Mode. Sensor ID set to value 9. Walk test will beep nine times.

10 ID10 Beacon Mode. Sensor ID set to 10. Walk test will beep once. When the Sensor is tripped, it keeps transmitting a beacon signal every second so that

it can be tracked (with appropriate directional finding equipment) if it moves

location.

Sensitivity Table

Press Button Value Maximum Sensitivity Description

0

IR900 IR901

Full Auto Mode

20’ to200’ 5’ to 50’

The Sensitivity automatically varies from maximum range to minimum range depending on how thermally stable the

environment is acting. If the environment is quiet, such as during

nighttime or on a cloudy day, the Sensitivity will be highest (value 5). If the environment is noisy, such as during a thunderstorm,

the Sensitivity will be at its lowest (value 1).

1 40 feet 10 feet Sensor will detect a person up to 40 feet (10 feet IR901).





Page 8

Note: The Table above correlates to an average size person (6 ft., 175 lb.) walking at a brisk pace (6 feet per

second) at an ambient temperature of less than 85 deg.F. Distances will be less when the targets velocity is slow or

the ambient temperature is between 90 deg F and 100 deg F. Minimum distance for the IR900 is 20 feet when the Sensitivity level is less than 2 and the target is moving quickly.

6.0 USING PASSIVE INFRARED SENSORS

Narrow Beam Passive Infrared sensing offers many advantages over other sensor types. When combined

with Auto-Threshold Sensing (ATS) circuitry, this technology is the most advanced when used in an outdoor environment. Its versatility, small size, long range, precise targeting, and target classifying allow it to be used

reliably in many diverse applications. However, having a fundamental understanding in how to use it is essential in getting good results.

Since the IR900 senses at an extremely long range, it is important to have it aimed at a proper background.

There are some setups that cannot be compensated by the ATS circuitry and will give you false alarms if you aren’t

aware of them. All setups involve maximizing what we call the signal to noise ratio. The signal corresponds to whatever it is we are interested in detecting, be it a bird, a human, an automobile, or an airplane, which all have

different sizes, shapes, and travel at different speeds. As far as the IR900 is concerned, they will all result in a different signal or infrared signature when the IR900 “see” them. This will involve placing the sensor at a certain

distance and orientation to the target so that the signal is maximized.

The thing we want to minimize is the noise, or whatever the IR900/901 sees when the target is not there.

This is the background such as bushes, trees or open terrain. Because of the sun’s radiation and the chilling effect of the wind, the outdoor environment often appears to an infrared sensor as a moving thermal mass, much like the

target we want to measure. Minimizing this unwanted noise involves aiming the sensor at an appropriate background. The safest backgrounds are open terrain (open distances up to 100 ft. an beyond) and solid ground.

6.1 Infrared Signal

The optimum signal produced by a human is at a distance of 100 feet for the IR900 and 30 feet for the IR901, with the person walking at a casual pace (3 ft./sec). This is strictly a function of the sensor’s optics, which is

fixed and determines the devices beam spread (6 ft. @ 100 ft. for the IR900). At 100 feet, a person completely fills

the sensing region of each beam causing a maximum signal. Further away than 100 feet, the person only partially fills the sensing region, thereby generating a smaller signal. Closer than 100 feet, the person passes through the

beams faster since they are closer together, likewise generating a smaller signal.

Therefore a person running by the sensor at 10 feet may register the same as a person walking by at 300

feet, neither being sufficient to trip the sensor. Automobiles will likewise be difficult to detect when the sensor is mounted close to the road and they are moving fast. To compensate, you can either move the sensor back from the

road (several hundred feet is OK) or you can aim the sensor upstream, which in effect causes the sensor beam geometry to widen. This will give much better results, especially if the sensor is aimed upstream, since the target

will be detected sooner, allowing the video more time to power up and start recording. Also, the RF transmission range between sensor and receiver can be kept short, which will improve the overall reliability.

Longer distances (600 ft.) can be used for larger vehicles (such as trucks or airplanes) since they better fill the sensing region at that distance. In the special case of detecting aircraft, the sensor should be located at the end

of the runway and aimed slightly above the horizon. It should also be turned 90 degrees (antenna oriented horizontal) so that the infrared beams are oriented top and bottom instead of side by side. This will result in a much

better signal as the aircraft descends through the beams on landing approach.

6.2 Infrared Noise

Page 9

As mentioned earlier, Infrared Noise includes all environmental disturbances that occur when the sensor is not detecting a target, such as wind chill on stationary objects or blowing tree leaves on moving objects. Much of

this type of disturbance is “filtered” out by the side-by-side orientation of the infrared beams. Thus, heat rising from a blacktop road will hit both beams simultaneously, causing a cancellation of their signals. However, under certain

circumstances, a tree branch moving back and forth as the wind blows can look like a person doing the same thing.

This can really be a problem if the sensor is aimed at the tree trunk, which is relatively warm due to sunlight, and the cooler leaves from a branch are blowing across it. Or a blade of grass located a few inches from the sensor,

blowing in the wind, can also “appear” as a person walking, again because of the smaller beam geometry at that distance.

To prevent unwanted false alarms or reduced sensor performance, the sensor should always be located on a

stationary object (large tree trunk), which will not move when the wind blows (avoid skinny pine trees). Any

offending grasses or branches should always be pruned away from the sensor’s field of view. Avoid aiming the sensor at trees with moving branches, especially at close distances (less than 100 feet). Better results will be

obtained if you aim the sensor at open spaces or bushes that are more solid in mass. Also, at close distance (20 feet or less), you should use the IR901 and program the sensitivity to a low value (value 1 or 2).

7.0 RX930 RECEIVER CONTROLS AND INDICATORS

7.1 Power

The RX930 Receiver/Processor Module accepts 12-volt DC power from the supplied “AA” battery pack.

The Receiver pulls 2.6 ma while it is “awake” and 5ua in the “sleep” mode. This translates to about 14 days of

operation (awake continuously) using alkaline batteries and about 1 month using Lithium batteries. If the Receiver is put to sleep during the night, these times can almost be doubled. The battery pack has a stereo 3.5mm

receptacle for programming the RX930 with the Palm Programmer (optional).

7.2 Program/Reset Button

This button resets the RX930 computer (clears the memory) and allows for limited programming (video

runtime variable). To clear the memory and reset the processor, press and hold the Program/Reset Button until the Red Light comes on, then release it. The Program/Reset Button can also reset the video runtime after an alarm

trigger, activate the video switcher module and cloner transmitter (optional for multi-camera operation or cloning

other devices with the same program). The Log-On function needed with the RX916 or RX920 series receiver is not necessary with the RX930 Receiver since the device has the audio beeper and power switcher integrated into the

same module. The Program Button is the black button located in the center of the grey silicon boot.

7.4 Red Light

The Red Light is used for programming and as an alarm indicator. It is also used to detect the presence of other interfering devices operating at 916.5 MHz when it flickers. It only illuminates during the Sensor Range

Test/Walk Test period (8 minutes) and automatically turns off thereafter for covert reasons. It flashes 7 times after a program is downloaded from the Palm Programmer.

7.5 Antenna

The RX930 Receiver’s antenna is connected to the SMA receptacle. The wire patch antenna and should be located several inches from leaves, vines, etc, for best reception. RF reception is at 916.5 MHz and is line-of-sight

for best range.

Page 10

SMA Antenna Connector

Program/Reset Button

Cloner Antenna (optional)

Red Light (LED)

RX930 Series Receiver/Processor Module

Figure 3

8.0 RX930 SERIES PROGRAMMING

The RX930 Receiver/Processor is designed to receive signals from sensors, process the information, and then control a video camera. Whenever an alarm occurs, the sensor sends a packet of data or alarm record that

characterizes the object that it detected. Some or all of the data can be used to qualify the alarm before a decision

is made to activate the camera. Additionally, various timers are available to control how long or at what times video is recorded. All of these variables are programmed into the Receiver by the Palm Pilot Programmer, a hand-held

computer that fits in your shirt pocket. Alternately, the most important variable, the Receiver’s Video Runtime Variable, can be manually programmed with the Program/Reset Button without using the Palm Programmer.

To use the Palm Programmer, first connect the RX930 Receiver to the Palm Programmer through the RX930 Palm Interface Cable. The RX930 receptacle is located on the “AA” battery box, which accepts the Palm Programmer

male stereo plug. Turn the Palm Programmer “ON”. Tap the “Home” Icon to get to the main page, and then select the RX900 icon, which executes the Programmer. You should see in the top left corner “Program Variables”. Tap

the “Menu” icon to activate the Programmer’s pull down menus, which read LOGIC, TIMERS, ID, and OUTPUT. Tap each of these menu bars to open up their selections, which are further discussed below. After your selections have

been made, push and hold down the RX930’s Program/Reset button until the Red Light starts flashing. Seven

flashes from the Red Light followed by a beeping sound indicate a successful download. If you have the cloner option, pressing the Program/Reset button again will terminate the beeping and wirelessly program any other RX930

compatible devices within RF range, such as the RIL-1 Remote IR Illuminator, the WPSU-1 Wireless Power Switching Unit, and the RPT-1 Remote Repeater. (If the Palm Programmer ever fails to turn on, it may require resetting, in

which case the RX930 Programming software will be lost. Contact IntelliCam for a copy via email.)

Alternately, the RX930 can be programmed without the Palm Pilot if you only require the Video Runtime

variable. To program the Video Runtime without the Palm Pilot, press and hold the Program/Reset Button until the Red Light comes on (Reset State). Immediately after the Red Light comes on, release the button and tap in the

Video Runtime variable. Each push of the button corresponds to 10 seconds, with a maximum entry of 4 minutes (24

Page 11

pushes). If you do not enter the Video Runtime after the RX930 is reset , the device will enter the default state,

whereby the sensor will tell it how long to run through the Sensor ID. See Section 8.2.2.

Pull Down Menus

Program Device Now

Home Icon

Menu Icon

Palm Programmer

Figure 4

8.1 Alarm Logic

The Receiver can be programmed to alarm only when certain logical conditions are met. These conditions are Sensor Group ID, logic AND function (dwell), target size factor, velocity, and direction.

1. Clear Alarm Logic

Clears all variables under LOGIC menu and resets them to default. Defaults are alarm on any sensor group, AND function inactive, alarm on any size object, alarm on any speed, alarm on any direction. Another way to reset

all variables under all menus to default is to tap the Palm Pilot HOME key and re-execute the RX900 Programmer. When the RX900 program is started up, all variables are reset.

2. Alarm on Sensor Group ID The Sensor can be programmed with a Sensor ID and a Group ID. The Sensor ID identifies which particular

sensor alarms (corresponds to number of beeps heard when using the Walk Test Module) and selects normal model, beacon mode, or data mode. Other than those functions, Sensor ID cannot be used for alarm screening. Sensor

Group ID is used for alarm screening, meaning that the Receiver can be programmed to screen out all alarms except

those from a particular Sensor Group.

Alarm on Sensor Group is activated by selecting (tapping) its menu item (under LOGIC menu). If Sensor Group is selected and the Sensor Group ID (under ID menu) is set for 5, then the receiver will only accept alarms

from sensors with Group ID’s of 5 and reject all others. This is useful when several sets of equipment are operating near each other and you don’t want alarms from one set interfering with the other.

Page 12

3. Alarm on Sensor Dwell

The Sensor Dwell function means that an alarm will not be processed until the Receiver processes 2 alarms from the same or different sensor within a specified time period (specified under the TIMERS menu, AND

Windowtime). Thus a setup can be configured so that an alarm will be generated only when several people walk

down a trail, when a road becomes “busy” with traffic, or when a person stops (dwells) in an area, causing multiple alarms.

The Sensor Dwell function is activated by selecting its menu item (under LOGIC menu). AND WindowTime

(under TIMERS menu) should also be set for an appropriate time period for the Dwell function to last. Thus, when the 1st valid alarm is received, the window time period begins. If another alarm occurs before the window time

period expires, the alarm will be processed by the Receiver. Otherwise, nothing will happen.

4. Alarm on Sensor A AND B

The A AND B function works identical to the Sensor Dwell function, accept that the 2 alarms must come from

different Sensor ID’s (the same sensor alarming twice within the time period will not register as a valid alarm…only

different sensors will cause alarm).

One application would be setting up 2 Passive Infrared Sensors so that their beams intersect at a point. When using the Sensor A AND B function with a short AND Windowtime (2 sec), alarms will only occur when the

target walks into the exact point of intersection.

Another application would involve using a Passive IR Sensor and a Magnetic Sensor and alarming only when

both devices are tripped. In this case the material composition (thermal and metallic) can be used to screen for alarms. If Sensor Group is used in conjunction with the Sensor A AND B function, the “Grouped” sensor must be

tripped 2nd for an alarm to occur.

The A AND B function is activated by selecting its menu item (under LOGIC menu). AND WindowTime

(under TIMERS menu) should also be set as in Sensor Dwell.

5. Alarm on Small, Medium, Large Object

The relative size of the target can be selected so that alarms occur only when the appropriate size conditions

are met. Target Size Factors (SF) is determined by the number of Hot to Cold (or Cold to Hot) regions within the target, or its Infrared “Signature”. A person walking by will usually register a SF of 3, an automobile 3-4, and trucks

4-5. A person remaining in the field of view of the sensor could register a SF of 4-6. This is due to his continually bouncing back and forth between the sensor’s infrared beams.

Alarm on Size is activated by selecting the Small, Medium, or Large menu item (under LOGIC menu). If

Small is selected, then only SF’s of 2 or more will alarm. If Medium is selected, 3 or more. And if Large is selected,

4 or more. The sensor must be programmed in the Data Mode (Sensor ID 11-15) for the size factor function to work. Also, the Sensitivity setting of the sensor will affect the size factor reading somewhat.

6. Alarm on Fast, Slow Speed

The speed of the target can be selected so that alarms occur only for fast or slow moving targets. A Speed Threshold (under LOGIC menu) of from 5 to 55 mph must first be set before a relative measurement can be

made. Target velocities over the threshold will be interpreted as “fast” and below the threshold will be interpreted as “slow”. Thus people walking can be screened from people on bikes, cars, or other fast moving objects. Vehicles

that are slowing down to turn can be separated from the normal traffic, etc.

Page 13

Alarm on Fast, Slow is activated by selecting the Fast or Slow menu item (under LOGIC menu). Alarm Speed

Threshold should also be selected to an appropriate value. For the speed function to be accurate, the IR900 Sensor should be placed perpendicular to the road at a distance of 150 feet from the road. Its sensitivity should be

manually set for a value of 3 for best results.

7. Alarm on Right to Left, Left to Right

The direction of the target can be selected so that alarms occur only for targets moving in a certain direction, be it left to right, or right to left. If the direction that the sensor is transmitting is incorrect, then simply

flip the sensor over with the antenna pointed downward to correct it or else select the Invert Direction menu item.

Alarms on Right to Left or Left to Right is activated by selecting its menu item (under LOGIC menu).

8.2 Timers

After an alarm passes the LOGIC screening and is determined to be valid, there are various timers that

determine how long the video runs and under what conditions. These timers are explained as follows:

1. Clear Timing Variables

Clears all variables under TIMERS menu and resets them to default. Defaults are Runtime set for sensor ID,

no Delay, AND Windowtime set for maximum (4 min.), no Time lapse activation, no Tape Rewind, and no Time Windowing (receiver stays on constantly). Another way to reset all variables under all the menus to default is to tap

the Palm Pilot HOME keys and re-execute the RX900 Programmer. When the program is started up, all variables are

reset.

2. Run Time

The Run Time variable sets the amount of time that the video runs. Run Time is selected under the TIMERS

menu, with selections from 10 seconds to 4 minutes. You should set the video runtime to correspond to the type of target that you want to capture on film. For instance, vehicles or moving targets that will be in and out of the

camera’s field of view quickly will require a runtime of 10 to 20 seconds. People or stationary targets around a fixed location will require a runtime of 1 minute to 4 minutes. The disadvantage of using long video runtimes will be if

you setup in a very unstable area and get a lot of false alarms, which will use up limited tape.

Runtime is re-triggerable, meaning that subsequent alarms will reset the runtime to the programmed value.

Example: The Runtime is programmed for 1 minute. An alarm triggers the video, which will run for 1 minute, however, 15 seconds before the video shuts off, another alarm occurs, which resets the video runtime for another

minute. After the video shuts off, it will have run a total of 1 minute and 45 seconds.

If no value (default) is programmed for Runtime, the Sensor ID x 10 will be used to tell the video how long

to run (i.e. Sensor ID=1, Runtime=10 sec, Sensor ID=2 Runtime=20 sec, etc.).

The Video Runtime can be manually programmed, similar to the IR901 Sensor, by performing the following

steps:

1.) Press the Program/Reset Button and hold it down until the Red Light comes on.

2.) After the Red Light comes on, immediately release the button and enter the Video Runtime Variable

(1=10 seconds, 2=20 seconds, 3=30 seconds, 24 (max)=4 minutes). The Red Light flashes each time you push the button down. After the Runtime is entered, the RX930 will “play back” the number you entered so

Page 14

that it may be verified as being correct. After playback, the RX930 enters its operational mode and is ready

to accept alarms from the sensor.

3.) Runtime is the only variable that can be manually programmed without the Palm Programmer. Manually programming the Video Runtime will erase all other variables that may have been previously programmed

with the Palm Programmer.

3. Delay Time

After an alarm occurs, the Receiver can be programmed to delay before starting the video runtime. You

may want to program a delay in an application where the target passes the Sensor along a trail and takes several minutes to reach the area where the video camera is setup, thereby saving tape. Delay Time is selected under the

TIMERS menu with selections from 10 seconds to 4 minutes.

4. AND WindowTime

See Alarm On Sensor AND function or Dwell under the LOGIC menu for an explanation. AND WindowTime is

selected under the TIMERS menu with selections from 2 seconds to 2 minutes.

5. Time Lapse Period

The Time Lapse Period is useful in scientific studies where the progress of something changing can be

captured in “snapshots” over a long time period. At preset intervals the video will start recording without receiving an alarm from the sensor for a period determined by the Runtime variable. Time Lapse Period is selected under the

TIMERS menu with selections from 1 hour to 24 hours. If a 24 hour (1 day) selection is made, the Time lapse

function can be used to report battery life in the Cell phone Dialer application. Be sure to also select the exposure time with the Runtime variable under the RUNTIME menu.

6. Rewind Tape Length (Not available on RX900) NOT AVAILABLE ON DIGITAL SYSTEMS

The Rewind function automatically rewinds the tape when it reaches the end, allowing for an endless tape. This feature can be useful in long-term surveillance of a highway where only the last week of information prior to an

event is important, such as the case of arson. A selection is made according to the length of tape being used, 1 hour commonly selected for a 1 hour tape. If you are using the camcorder in the LP mode, be sure to double the

effective tape length. Rewind is selected under the TIMERS menu with selections from 1 minute to 4 hours.

7. Wake Time/Sleep Time

The Receiver can be programmed to “wake up” and “sleep” at pre-selected times, screening out time period

of no interest. Applications include monitoring an equipment yard in the evenings for theft, but sleeping during the day so that authorized traffic isn’t recorded. Another reason to sleep the Receiver is to conserve battery power

during periods of no interest (power drain reduced by factor of 5). Wake Time is selected under the TIMERS menu

with an hour that corresponds to when the Receiver wakes up and accepts alarms. Sleep Time is selected under the same menu with an hour that corresponds to when the Receiver turns off and goes to sleep.

8.3 ID

The ID menu allows for address changes. Sensor Group ID, Receiver ID, and Receiver Group ID’s of the Sensor must all match up to identical addresses programmed in the Receiver for an alarm to be processed. This is

to prevent someone else’s Sensor from triggering your equipment, usually in urban environments. It also prevents other digital wireless devices that may be operating on the same frequency from interfering with the Receiver.

Page 15

Sensor Group ID, Receiver ID, and Receiver Group ID are all selected under the ID menu with values of 1 to

15 available. Of course, the Sensor must also be programmed with the same information to have them talk to each other. The Receiver will accept any ID in the Range Test mode, so just because it works in the Range Test Mode,

doesn’t necessarily mean that the ID’s match. Clear ID resets all ID’s to default with Sensor Group ID reset to 1, Receiver ID to 5, and Receiver Group ID to 1.

9.0 SYSTEM I QUICK SETUP

1. Setup the Sensor (refer to section on Range Test, Walk Test).

2. Open OtterBox Case. Replace 8 “AA” alkaline cells if necessary (2-3 weeks normal use).

3. Prepare Digital Recorder (refer to DVR Manual).

a. Insert battery under DVR and insert SD card into slot on left side of DVR. b. Set the correct Date and Time on the DVR under MENU

c. Connect Micro-MV Connector right side of DVR.

4. Attach the MiniCam (small CCTV camera) to Video Jack (small military connector) of Armored Cable. Attach MiniCam to Tree Mount Clip. Aim the Mini-Cam at the target area (see #6 below). Camouflage the

MiniCam, being careful of lens glare. Note: The MiniCam has an automatic iris for light level compensation

and is pre-focused. The entire unit is water-resistant, but not submersible.

Attach Antenna to the RX930 Module’s SMA receptacle. Tie off the Antenna to a small bush or hang it from a limb using the extension cable. Camouflage the Antenna wire. For best results, try to keep leaves

and foliage away from the antenna. It makes no difference how the antenna is oriented, but for best

results, keep it in a vertical plane.

5. Attach the Armored Cable into the OtterBox Case and twist it until the bayonet connector clicks.

6. Set the DVR REC/ON/OFF switch to OFF. Insure that the Vibrate switch on the top is set to OFF. The

OFF/TV/LCD switch should be in LCD while setting up the system. After the system has been set up, turn the LCD monitor to OFF to conserve battery power. Pull the battery tab to activate the Video

Controller’s “AA” battery pack (or insert “AA” batteries). Press and hold the Program/Reset Button until the Red Light comes on (about 2 seconds) and enter the video runtime variable by tapping the button once for

each 10 seconds of runtime. After playback, tap the Program/Reset Button to toggle the DVR on. The DVR should power up in the Main Menu mode. To view the camera, use the down arrow on the DVR and scroll to

Recorder Setting. Press Enter. Now scroll down to Video Line in REC and press Enter. You should have a

picture on the LCD screen. Aim the Mini-Cam at the target while viewing the picture in the LCD display screen. Turn the DVR off by once again tapping the RX930’s Program/Reset Button. Pushing the

Program/Reset Button will repeatedly toggle the DVR on and off. The RX930, DVR and MiniCam can be tested in this mode prior to field deployment.

8. (Optional) Program the Receiver’s Video Runtime with the Palm Programmer. This is done by connecting the Palm Programmer’s 3.5mm male plug up to the female receptacle on the “AA” Battery Box. Turn the

Palm Pilot on and tap the Palm Programmer Icon in the main window. Make your programming selections and when you are finished, press and hold the Program/Reset Button until the Red Light starts to flash. The

Red Light should flash 7 times to indicate “programming complete”, after which you can remove the Palm Programmer.

Page 16

The RX930 will also begin to beep, which allows you up to one minute to clone (optional feature) other devices such as the RIL-1 Remote Infrared Illuminator or another camera system with the same

program if desired. To begin cloning, simply tap the Program/Reset Button and the program will be wirelessly transferred to other wireless receivers in the immediate area. This feature is optional to the

RX930.

9. Setup the Sensor and Walk Test the Sensor so that an alarm occurs. The DVR should turn ON in the Record Mode simultaneous to the RX930’s Red Light latching on (indicating valid alarm). Reset (turn off) the

Video by pushing the RX930’s Program/Reset Button.

Note: Failure to activate the Receiver/Video after a sensor alarm may mean that you are out of RF range –

Check by resetting the Sensor to the Range Test Mode and tripping it. The RX930’s Red Light should flash and the internal beeper should beep in concert with the Sensor’s Red Light, indicating solid RF reception.

Absence of the RX930’s Red Light flashing or flashing irregular means that you are out of RF range (maximum range depends on terrain and other factors).

10. Turn off the LCD Display (conserves DVR’s battery) and shut the Otterbox lid.

11. When returning to the site to check the video, always trip the sensor so that you have an established ending date for the period of surveillance. This may be useful for troubleshooting the system if

problems occur. Open the Otterbox Case and turn on the DVR using the RX930’s Program/Reset Button. You can review the evidence on the SD card by pressing the DVR’s Video Files section from the Main Menu.

Page 17

10.0 TECHNICAL INFORMATION

12.1 Sensor Specifications

IR900 IR901

Sensing Method Dual Element Pyroelectric Detector

Max. Detection Range @ 80 deg. Ambient)

Personnel

Vehicles

200 feet 50 feet

400 feet 300 feet

RF Output Power 1 mw, per FCC Part 15 Rules (FCC ID RVL-

SICSAW916)

Modulation OOK, 2-4Khz

RF Frequency 916.5 MHz (SAW stabilized)

Battery Type 4 “AAA” (IR900B) or 2, CR1225 3 volt Lithium

Battery Life 4-6 months 21 days

Operating Temperature 14 F to 122F (-10 C to +50 C)

Field of View 5 degrees 20 degrees

Dimensions 1.0” diam. 1.0” diam.

4.8” long 2.8” long Weight

2.5 oz (60 g) 1.8 oz (45 g)

12.2 RX930 Receiver Specifications

Frequency 916.5 MHz (SAW stabilized)

Sensitivity -98 dbm (100 ft. to 300 ft. range, line-of-sight)

Power Supply 5.0 – 12 volts DC external

Power Supply Current

Normal Operating

Sleep Mode

2.5 milliamps

300 micro amps

Electronic Output NPN Transistor (Open Collector, 20ma max)

Video Control Output Sony/Canon LANC protocol

Operating Temperature 14 F to 122 F (-10 C to +50 C)

Page 18

Dimensions

Weight

1.5” diam. X 1.2” length

4.0 oz (120g)

11.0 RF INTERFERENCE

This device complies with part 15 of the FCC rules (FCC ID RVL-SICSAW916). Operation is subject

to the following conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause

undesired operation.

When operating in an urban area, sources of interference can include 900 MHz cordless phones, spread spectrum phones, computers, and other data transmission devices. Interference caused by these

sources is usually of limited range (100 ft.) due to the fact that the FCC restricts the power output at this

frequency. The presence of interference is indicated by a flickering Red Light when the RX900 Receiver/Processor is first turned on (Range Test/Walk Test Mode). Although the RX900 will reject most of

this interference, it is best to locate the interfering source and remove it (if possible) prior to doing installation, or degraded reliability could result.

FRN 0010373413

Warning: This device operates under Part 15 of the FCC Rules. Any modification not expressly approved by IntelliCam, LLC

may void the warranty and the users authority to operate this device.

Page 19

Addendum

OFF/TV/LCD

Switch

Turn to OFF

when finished

setting up

system

Record/On/Off

Turn OFF

while using system.

You may view video

files in the ON

position

SD Card

Slot

Nylon cord is used

to remove DVR

from box

3.5mm jack for

programming

processor using

optional Palm

Programmer

Beeper allows

user to hear

sensor

activation and

range test

Slot for spare DVR

battery

Slot for

IR901

Sensor

IR port for using

remote control of

DVR – Aim

remote at this

window

Page 20

IR Illuminator and Low Light Camera

1.0 General Information

The IR Illuminator is used together with the Sony EX-View Low Light Camera or the Sony Super HAD

Day/Night Camera for recording in total darkness. The illuminator provides invisible illumination (naked to

the human eye) for up to 30 feet distance from the subject. It is completely remote from the System I so

that the desired illumination can be brought on the subject without running wires for long distances. This

also reduces the security risk should the target arrive with Night Vision goggles. If he finds the illuminator,

he won’t be able to follow wires to the camera and destroy the evidence (video).

Program/Reset Black Button

14 Infrared LEDS

Batteries (8 “AA” Cells) Illuminator Head w/

Rubber Cover RX930 Receiver/Processor

Remote IR Illuminator

With integrated RX930 Receiver/Processor

1.1 Illuminator Control Housing

The IR Illuminator uses 8 “AA” batteries for power. This should power the illuminator for about 1 month

in the standby mode (waiting for an alarm) with 1 hour of continuous video illumination when recording.

The illuminator should be programmed with the same Video Runtime as the System I so that the

illumination period will coincide with the recording times, thereby conserving power only when it’s

needed. The Illuminator only functions during the night, automatically turning off during the day to

conserve batteries. This is accomplished by a photocell. Access to the battery compartment is found by

removing the bottom rubber cover from the case. This slips off the battery holder by pushing

the bottom and pulling the illuminator head out. The batteries can then be replaced. Replace the batteries

only with alkaline or lithium types, and then slide the holder back into the case, reversing the above

procedure.

Page 21

1.2 RX930 Receiver/Processor

The RX930 Receiver/Processor is integrated into the illuminator head. It receives alarm signals from the

sensor and turns on the illuminator to provide covert illumination for the low light camera. The only

programming variable is the illuminator “Runtime. To program the Runtime, press and hold the RX930’s

Black Button until the Red Light comes ON. Immediately after the Red Light comes ON, release the button

and tap in the Runtime Variable. Each time you tap the button the Runtime is incremented by 10 seconds

(1=10 sec, 2=20 sec, 3=30 sec,….6=1 min, 24=4 min maximum).

After you tap in the Runtime, the RX930 will flash back the number you entered in for verification. The

unit is now ready to receive sensor alarms. The colored LED on the unit will stay active for 10 minutes

after the unit is programmed and after 10 minutes goes covert (will not come on when the sensor activates

the illuminator). If you wish to reactivate the colored LED, simply toggle the unit On/Off by pressing the

Black Button briefly. The illuminator can be toggled on or off without the sensor alarming by

pushing the RX930’s Black Button. This can be useful when setting up and aligning the illuminator “head”.

1.3 Illuminator Head

The illuminator head (LED End) should be aimed at the target area. For best results, position the

illuminator within 30 feet of the subject with the camera behind the illuminator. This way the lighting will

illuminate the front of the subject and will not “flood” the camera. If you position the camera off to the

side, you may not have the desired lighting effect, which will result in the subject’s side profile instead of a

facial profile. The illuminator head is a fairly narrow beam with a range of 30 feet long by 15

feet wide when used with the Sony Ex-View Low Light Camera. It can be tree mounted with the supplied

bracket or ground mounted. Do not cover the front of the head with any netting or other material, as this

will severely limit its usefulness. Using a low light camera with a telephoto lens will greatly improve your

ability to read license plates or identify faces.

1.4 LLC Low Light Camera

The LLC is a black and white camera, which can be used with very low levels of light (moonlight) without

the illuminator. When there is insufficient moonlight or total darkness, the LLC can be used with the IR

Illuminator. Attach the LLC to the System I Video Cable. Next turn the System I on by pressing the button

on the receiver/processor. Go to a “live view” mode by following instruction #6 on page 15 of this manual.

Turn the camera off by again pressing the RX930 Black Button. Next, clip the camera into the supplied tree

mount and aim the camera at the target area. Adjust the focal length and/or aperture as needed or if

required.

IntelliCam, LLC

11138 Air Park Road, Suite H

Ashland, VA 23005

(804) 798-1004

www.intellicam-llc.com

Email: [email protected]

Documents

INTELLICAM SYSTEM LL USER’S MANUAL REVISION 6