Upload
lynhan
View
214
Download
0
Embed Size (px)
Citation preview
8.12014−04−28 Integrity Architectural Detail Manual11708532
CHAPTER 8
INTEGRITY WOOD−ULTREXSLIDING PATIO DOOR
Unit Features 8.2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Egress Measurements 8.3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Minimum and Maximum Sizing, Certified Sizes and Mulling Guidelines 8.4. . . . . . . . . . . . . . . . . . .Mulling Guidelines 8.5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Measurement Conversions 8.6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Standard Size Chart 8.7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Elevations 8.8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Section Details − 4 9/16� Jamb 8.10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Section Details − 6 9/16� Jamb 8.11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Section Details − Transoms and Mullions 8.12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Section Details − Mullions 8.13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Divided Lite Options 8.14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Available Divided Lite Patterns 8.15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Installation Suggestions 8.16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ATTENTION:� Specifications and technical data are subject to change without notice.� Number is parentheses () following measurements are the metric equivalents in millimeters rounded to
the nearest whole number� Allow 1/16� (2) tolerance on all measurements.� Optional interior casing for round top units and interior mullion trim are shipped loose for field installation.� For answers to technical questions about Integrity products you may call our
Integrity Support Line: 1−800−587−2712.
� Website: www.integritywindows.com
8.22014−12−22 Integrity Architectural Detail Manual11708532
FRAME AND PANEL:The frame and panel exteriors are made of Ultrex�, an advanced fiber reinforced material that is resistant to thermal conductance. Ultrex patentedcoating system meets all the requirements of AAMA 624-10. Exterior colors: Stone White, Pebble Gray, Bronze, Evergreen, Cashmere, or Ebony.The interior is non finger−jointed pine, kiln dried to a moisture content of 6−12% at time of fabrication. Water-repellant, preservative treated inaccordance with WDMA I.S.4. Interior wood is available as Pine bare wood or factory−applied white interior finish.
FRAME:Composite frame thickness is 1 5/16� (33). Frame width of 4 9/16� (116). 4/4 non finger−jointed pine interior stop is applied to all units. Sill is Ultrexwith oak interior sill liner. Ultrex is .080� (2) thick.
PANEL:Composite sash thickness of 1 3/4� (44). Ultrex is .080� (2) thick.
JAMB EXTENSION:6 9/16� (167) and 6 13/16� (173) jamb extension available factory applied or in lineal lengths for field application. Assemblies with 6 9/16� and 6 13/16�jamb extensions − add 1/4� to width and 1/8� to height of Rough Opening.
HARDWARE:Standard Handle: Single point non−keyed zinc substrate handle lock. Handle set: interior and exterior selected separately. Available in Almond Frost.White, Brass PVD, Satin Nickel PVD, or Oil Rubbed Bronze PVD. Provides an interior thumb lever to engage the locking and unlocking of the operatingpanel. Keyed and keyed alike options are available. Handle is 7 5/8� tall, 2 21/32� wide by 1 13/16� deep.
INSTALLATION:Factory applied folding nailing fin and drip cap system. Optional installation brackets for masonry available. Factory supplied field mulling kits areavailable for standard assemblies.
GLAZING:All units are manufactured with a 3/4� (19) Tempered Insulating G;ass with Low E2, E3 and E1 coatings including argon gas fill. All glass is of a selectquality complying with ASTM C 1036. Insulating glass is manufactured and tested to pass level ASTM E 2190 and is IGCC certified. The glazing sealis a silicone bedding on both interior and exterior surfaces utilized in a sandwich style sash. STC/OITC values are available for 3.1/3.1 standard glass.Optional 3.1/4.7 STC/OITC Upgrade glass is available. STC and OITC ratings are tested in accordance with ASTM E 90-09. See the ProductPerformance chapter for values.
WEATHER STRIP:All units have full perimeter frame weather strip. The operating panel is sealed to the frame using a flexible bulb gasket with leaf weather strip. Thestationary panel is sealed to the header using a flexible leaf weather strip. The meeting stiles are sealed using an interlock with a fin seal pile weatherstrip. The operating panel has a drip seal with a fin seal pile weather strip at the bottom. All weather strip is beige colored PVC standard.
SCREEN:Top−hung extruded aluminum screens are available as an option. Single operating screen only. Aluminum metal to match exterior Ultrex color.Charcoal color fiberglass (non−corrosive) screen material. Includes all mounting and latching hardware. The screens are handed.
REMOVABLE INTERIOR GRILLES:Bar: Pine wood, 3/4� (19) Pattern: Standard rectangular pattern. Available in Pine bare wood or factory applied white interior finish.
INTERIOR / EXTERIOR SIMULATED DIVIDED LITES (SDL):Interior bar: 7/8� (22) wide bars. Pine bare wood or factory applied white finish, to match interior. Exterior bar: Ultrex, 7/8� (22) wide bars, finish to matchexterior. Pattern: Standard rectangular pattern, 9 lite prairie cut per panel, 6 lite prairie cut on transom or Cottage style cut.
GRILLES−BETWEEN−THE−GLASS (GBG):11/16� (17) contoured aluminum bar placed between two panes of glass. Pattern: Standard rectangular pattern, or 9 lite prairie cut per panel or 6 lite prairiecut on transom. Exterior color determined by panel color. Interior Color: White or Bronze.
EXTERIOR CASING:Non−integral to the unit. Fastened to the exterior wall with barb and kerf 2� (51) brick mould available as a header and jamb surround. 3 1/2� (89) flatcasing available as a header and jamb surround. Also available with 1� (25) ranch style header overhang.
O = Stationary PanelX = Operating Panel
All units viewed from exterior.
XO OXOOX XOO OXO Left OXO Right
3 Panel Units2 Panel Units
OPERATION
SLIDING PATIO DOOR
UNIT FEATURES
8.32014−04−28 Integrity Architectural Detail Manual11708532
XO Patio Door Unit Not to Scale
Clear Height atHead Jamb
ClearWidth
Clear Height at Sill
Code restrictions may vary depending on your local building codes.For additional information contact your local code department for IBC and IRC requirements.
Minimum Value forNet Clear Opening
Desired Dimension Formula
2 Panel Door
= ISPD frame OM width − Panel Width − 5.870
3 Panel Door
= ISPD frame OM width − (Panel Width x 2) − 5.870
78 in (IRC 2012)80 in (IBC 2012)
Egress opening height, in = ISPD frame OM height − 4.178
Egress Conversions
Standard Sliding Patio Door
Egress opening width, in32 in
ft−in mm
5−0 1−11 1/2 (597)
6−0 2−5 1/2 (749)
7−6 1−11 1/2 (597)
9−0 2−5 1/2 (749)
ft − in mm
6−5 6−3 5/16 (1913)
6−8 6−5 13/16 (1977)
All HeightConfigurations
Net Clear OpeningWood Ultrex Sliding Patio Door
Height
Unit Type Call NumberNet Clear Openings
2 Panel Operator(OX / XO)
Width
Unit Type Call Number
Net ClearOpenings
3 Panel Operator(OXO, OOX, XOO)
SLIDING PATIO DOOR
EGRESS MEASUREMENTS
8.42014−04−28 Integrity Architectural Detail Manual11708532
in mm in mm in mm in mm
2 − PanelOperator
59 (1499) 79 1/2 (2019) 71 (1803) 82 (2083)
3 − PanelOperator
88 1/2 (2248) 79 1/2 (2019) 106 1/2 (2705) 82 (2083)
Door Transom 59 (1499) 15 3/4 (400) 106 1/2 (2705) 15 3/4 (400)
Minimum and Maximum Frame Size Guidelines
Min Width Min Height Max Width Max HeightUnit Type
NOTE: Special sizes are available in 1/64� increments, not to exceed the minimum or maximum sizes listed above.
ProductAir Tested
to psfWater Tested
to psfDesign
Pressure psfCertification
RatingMax
Overall WidthMax
Overall Height
Integrity SlidingPatio Door(XO−OX)
1.57 4.5 30 R−PG30−SD 71 82
Integrity SlidingPatio Door
(OOX)1.57 4.5 30 R−PG30−SD 106 1/2 82
Integrity SlidingPatio Door
(OXO)1.57 4.5 30 R−PG30−SD 106 1/2 82
SLIDING PATIO DOOR
MINIMUM AND MAXIMUM SIZING ANDCERTIFIED SIZES
8.52014−04−28 Integrity Architectural Detail Manual11708532
ROUGH OPENING TABLE FOR ASSEMBLIES
HEIGHT: Single unit Rough Opening height MINUS 1/2� = Frame height. ADD all frame heights PLUS 1/2� = Total Rough Opening height.
NOTE: Assemblies with 6 9/16� (167) or 6 13/16� (173) jambs add 1/4� to width and 1/8� to height of Rough Opening.
NOTE: Field mulling beyond 110� (2794) x 112� (2845)is not recommended.
Factory Door Assemblies
� Assemblies up to 1 unit wide by 2 units high� MAXIMUM ROUGH OPENING not to exceed 72� (1829) X 100 1/2� (2553)
SLIDING PATIO DOOR
MULLING GUIDELINES
8.62014−04−28 Integrity Architectural Detail Manual11708532
From To
in mm in mm in mm
Masonry Opening Rough Opening + 1/2 (13) + 1/2 (13) + 1/4 (6)
Masonry Opening w/BMC Rough Opening + 1/2 (13) + 1/2 (13) + 1/4 (6)
OM of Frame Rough Opening + 1 (25) + 1 (25) + 1/2 (13)
Daylight Opening Rough Opening � 2 + 10 (254) � 3 + 14 1/2 (368) + 7 7/16 (189)
in mm in mm in mm
OM of Frame OM of Panel � 2 + 1/8 (3) � 3 + 1/8 (03) −2 5/16 (59)
Daylight Opening OM of Panel + 4 5/8 (117) + 4 5/8 (117) + 4 5/8 (117)
in mm in mm in mm
Daylight Opening Glass + 1 1/4 (32) + 1 1/4 (32) + 1 3/16 (30)
Height
Frame
Operating Panel
Glass
Unit Measurements − Operating PanelsWidth2W
Width3W
From To
in mm in mm
Masonry Opening Rough Opening + 1/2 (13) + 1/4 (6)
Masonry Opening w/BMC Rough Opening + 1/2 (13) + 1/4 (6)
OM of Frame Rough Opening + 1 (25) + 1/2 (13)
Daylight Opening Rough Opening + 5 3/8 (137) + 4 7/8 (124)
in mm in mm
Daylight Opening Frame + 4 3/8 (111) + 4 3/8 (111)
in mm in mm
Daylight Opening Glass + 1 9/16 (40) + 1 9/16 (40)
Glass
Unit Measurements − Transoms
Width Height
Frame
Frame
SLIDING PATIO DOOR
CONVERSIONS
8.72014−08−25 Integrity Architectural Detail Manual11708532
ft − in mm ft − in mm ft − in mm ft−in mm in mm
5−0 4−11 1/2 (1511) 5−0 (1524) 4−11 (1499) 2−5 5/8 (752) 25 (635)
6−0 5−11 1/2 (1816) 6−0 (1829) 5−11 (1803) 2−11 5/8 (905) 31 (787)
7−6 7−5 (2261) 7−5 1/2 (2273) 7−4 1/2 (2248) 2−5 5/8 (752) 25 (813)
9−0 8−11 (2718) 8−11 1/2 (2731) 8−10 1/2 (2705) 2−11 5/8 (905) 31 (787)
ft − in mm ft − in mm ft − in mm ft−in mm in mm
6−5 6−7 3/4 (2026) 6−8 (2032) 6−7 1/2 (2019) 6−5 3/16 (1960) 72 9/16 (1843)
6−8 6−10 1/4 (2089) 6−10 1/2 (2096) 6−10 (2083) 6−7 11/16 (2024) 75 1/16 (1907)
Standard Sliding Patio Unit Measurements
Height
Unit Type
AllConfigurations
Width
CallNumber
DaylightOpening
Panel OMMasonryOpening
RoughOpening
FrameSize
2 Panel
DaylightOpening
3 Panel
Panel OMUnit Type
CallNumber
MasonryOpening
RoughOpening
FrameSize
ft − in mm ft − in mm ft − in mm ft − in mm ft−in mm
7−2 5−11 1/2 (1816) 6−0 (1829) 5−11 (1803) 5−6 5/8 (1692) 68 3/16 (1732)
10−7 8−11 (2718) 8−11 1/2 (2731) 8−10 1/2 (2705) 8−6 1/8 (2594) 103 11/16 (2634)
ft − in mm ft − in mm ft − in mm ft − in mm ft − in mm
AllConfigurations
1−6 1−4 (406) 1−4 1/4 (413) 1−3 3/4 (400) 0−11 3/8 (289) 12 15/16 (329)
Glass Size
Direct Glaze
Standard Direct Glaze Door Transom Unit Measurements
Height
DaylightOpening
Glass Size
Width
Unit TypeCall
Number
MasonryOpening
RoughOpening
FrameSize
Unit TypeCall
Number
MasonryOpening
RoughOpening
FrameSize
DaylightOpening
SLIDING PATIO DOOR
STANDARD SIZE CHART
ISPD6068 XOISPD5068 XO
ISPD5065 XO ISPD6065 XO
4−11 1/2 (724)5−0 (737)4−11 (711)
5−11 1/2 (1816)6−0 (1829)5−11 (1803)
6−7
3/4
(202
6)6−
8(2
032)
6−7
1/2
(201
9)
6−10
1/4
(208
9)6−
10 1
/2(2
096)
6−10
(208
3)
Mas. Opg.Rhg. Opg.Frame Size
Mas
. O
pg.
Rhg
. Opg
.F
ram
e S
ize
4−11 1/2 (724)5−0 (737)4−11 (711)
5−11 1/2 (1816)6−0 (1829)5−11 (1803)
ISPDDG 7216 ISFDG 10716
Mas
. O
pg.
Rhg
. Opg
.F
ram
e S
ize
Mas. Opg.Rhg. Opg.Frame Size
5−11 1/2 (1816)6−0 (1829)5−11 (1803)
8−11 (2718)8−11 1/2 (2731)9−10 1/2 (2705)
1−4
(406
)1−
4 1/
4(4
13)
1−3
3/4
(400
)
NOTE:SDL and GBG lite cut is not equal, to align with Patio Door.
Equal lites are available.
Transoms with SDL or GBG lites may be manufactured to align with pattern below in door. Lite cut of GBG will only align with lite cut of door it is intended for.
Round top transoms available for field assembly, refer to round top chapter for more information.
ISPD5068 OX ISPD6068 OX
ISPD5065 OX ISPD6065 OX
8.82014−04−28 Integrity Architectural Detail Manual11708532
SLIDING PATIO DOOR
ELEVATIONS 2 AND TRANSOMS
ISPD7665 X00
ISPD7668 X00
Mas. Opg.Rhg. Opg.Frame Size
Mas
. O
pg.
Rhg
. Opg
.F
ram
e S
ize
6−10
1/4
(208
9)6−
10 1
/2(2
096)
6−10
(208
3)
7−5 (2261)7−5 1/2 (2273)7−4 1/2 (2248)
6−7
3/4
(202
6)6−
8(2
032)
6−7
1/2
(201
9)
6−10
1/4
(208
9)6−
10 1
/2(2
096)
6−10
(208
3)
6−7
3/4
(202
6)6−
8(2
032)
6−7
1/2
(201
9)
Mas. Opg.Rhg. Opg.Frame Size
8−11 (2718)8−11 1/2 (2731)8−10 1/2 (2705)
ISPD9068 X00
ISPD7665 00X ISPD7665 0X0
ISPD7668 00X ISPD7668 0X0
ISPD9068 00X ISPD9068 0X0
ISPD9065 X00 ISPD9065 00X ISPD9065 00X
8.92014−04−28 Integrity Architectural Detail Manual11708532
SLIDING PATIO DOOR
ELEVATIONS 3 PANEL DOORS
2 PANEL XO OPERATORJAMB DETAIL
HEAD
SILL
JAMB
3 PANEL OXO OPERATORJAMB DETAIL
1 11/16�(43)
1 7/8�(48)
3 11/16�(93)
3 5/16�(84)
1 5/16�(33)
3 9/32�(83)
4 9/16�(116)
5 21/32�(144)
4 9/16�(116)
5 21/32�(144)
Fra
me
Siz
e
FrameSize
2 3/8�(60)
1 1/4�(31)
3 5/16�(84)
FrameSize
4 9/16�(116)
5 21/32�(144)
2 3/8�(60)
1 1/4�(31)
3 5/16�(84)
4 5/8�(118)
4 9/16�(116)
5 21/32�(144)
Scale 3� = 1� 0�
1 5/16�(33)
8.102014−12−22 Integrity Architectural Detail Manual11708532
SLIDING PATIO DOOR
SECTION DETAILS 4 9/16� Jambs
2 PANEL XO OPERATOR JAMB DETAIL
HEAD
SILL
JAMB
3 PANEL OXO OPERATOR JAMB DETAIL
6 9/16�(167)
7 21/32�(194)
3 3/8�(86)
3 11/16�(93)
2�(51)
1 11/16�(42)
FrameSize
6 9/16�(167)7 21/32�
(194)
4 5/8�(118)
2 3/8�(60)
3 5/16�(84)
1 7/32�(31)
FrameSize
1 7/16�(36)
1 7/32�(31)
3 9/32�(84)
2 3/8�(60)
3 5/16�(84)
6 9/16�(167)
7 21/32�(194)
Fra
me
Siz
e
Scale 3� = 1� 0�
1 7/16�(36)
8.112014−12−22 Integrity Architectural Detail Manual11708532
SLIDING PATIO DOOR
SECTION DETAILS − 6 9/16� Jambs
HEADJAMB
5 21/32�(144)
4 9/16�(116)
11/16�(17)
1 5/16�(33)
2 3/16�(56)
2 1/16�(52)
2 1/16�(52)
11/16�(17)
1 5/16�(33)
2 3/16�(56)
1 5/16�(33)
4 9/16�(116)
5 21/32�(144)
2 1/16�(52)
11/16�(17)
2 3/16�(56)
SILL
Fra
me
Siz
e
Da
ylig
ht
Op
en
ing
11/16�(17)
FrameSize
DaylightOpening
4 9/16� Jambs 6 9/16� Jambs
2 1/16�(52) 1 5/16�
(33)
2 3/16�(56)
FrameSize
DaylightOpening
2 5/16�(56)
2 5/16�(56)
6 9/16�(167)
7 21/32�(194)
1 7/16�(36) 2 5/16�
(59)
11/16�(17)
1 7/16�(36)
2 5/16�(59)
Fra
me
Siz
e
Da
ylig
ht
Op
en
ing
2 1/16�(52)
2 1/16�(52)
11/16�(17)
1 7/16�(36)
11/16�(17)
1 7/16�(36)
11/16�(17)
6 19/32�(167)
7 11/16�(195)
2 1/16�(52)
2 1/16�(52)
JAMB JAMB
Scale 3� = 1� 0�
8.122014−04−28 Integrity Architectural Detail Manual11708532
SLIDING PATIO DOOR
SECTION DETAILS − DIRECT GLAZE TRANSOM
DIRECT GLAZE TRANSOM OVER PATIO DOOR
1 1/16�(27)
1 3/8�(35) 2 1/4�
(57)5 5/16�(136)
Scale 3� = 1� 0�
8.132014−04−28 Integrity Architectural Detail Manual11708532
SLIDING PATIO DOOR
SECTION DETAILS − MULLIONS
DIVIDED LITE OPTIONS3/4�(19)
7/8�(22)
11/16�(18)
NOTE: * Optional 9 lite per panel Prairie cut.
RECTANGLE SDLEXAMPLE SHOWN
GBG or SDL
Conversion Formula:Total DLO − Total bar width
Number of lites= Individual DLO
* 6 lite prairie lite cuts on ISPDG 7216 or ISPDG 10716 dueto height limitations. GBGs not available in ISPDG 10716.
Frame Size
Fra
me
Siz
e
4� (102)DLO
7/8�(22)
3 9/32�(83)
Da
ylig
ht O
pe
nin
g
4�(102)DLO
3 11/16�(93)
7/8�(22)
7/8�(22)
7/8�(22)
4� (102)DLO
4�(102)DLO
7/8�(22)
7/8�(22)
7/8�(22)
7/8�(22)
COTTAGE LITE CUT
10� (254)DLO
* Horizontal bar is placed at 10� (254) daylight opening.
* Only available in SDL.
WOOD REMOVABLEGRILLE
SIMULATEDDIVIDED LITE SIMULATED DIVIDED LITE
WITH SPACER BAR
ALUMINUM GRILLEBETWEEN GLASS
7/8�(22)
Not to Scale
8.142014−04−28 Integrity Architectural Detail Manual11708532
SLIDING PATIO DOOR
SECTION DETAILS − DIVIDED LITE OPTIONS
8.152014−04−28 Integrity Architectural Detail Manual11708532
Notes:� Direct Glaze Transoms with GBGs or SDL will only align with the cut of the door it is intended to be mulled
with and may not have equally spaced lites unless otherwise indicated. For alternative GBG or SDL litealignment, order a Direct Glaze Rectangle with the divided lite option.
� An ISPDDG 7216 with GBGs or SDL will align over an ISPD CN60 width only.� An ISPDDG 10716 is available field−mulled or stand−alone only. Rectangular GBGs or SDL in a field−
mulled ISPDDG 10716 will align over an ISPD 9068 only. Rectangular GBGs or SDL in a stand−aloneISPDDG 10716 will be equally spaced.
Wood Grille GBG SDL
5065 3W5H 3W5H 2W5H 9−Lite 9−Lite 4 8
5068 3W5H 3W5H 2W5H 9−Lite 9−Lite 4 8
6065 3W5H 3W5H 2W5H 9−Lite 9−Lite 4 8
6068 3W5H 3W5H 2W5H 9−Lite 9−Lite 4 8
7665 3W5H 3W5H 2W5H 9−Lite 9−Lite 4 12
7668 3W5H 3W5H 2W5H 9−Lite 9−Lite 4 12
9065 3W5H 3W5H 2W5H 9−Lite 9−Lite 4 12
9068 3W5H 3W5H 2W5H 9−Lite 9−Lite 4 12
7216 6W1H 6W1H 4W1H 6−Lite Top 6−Lite Top N/A N/A
10716 9W1H 9W1H 6W1H N/A N/A N/A N/A
Direct Glaze Transom per unit
CNRectangular Prairie Cottage Lite Cuts
GBG or SDL Lite Cutper Panel
Total Liteper UnitSliding Patio Door per panel
SLIDING PATIO DOOR
AVAILABLE DIVIDED LITE PATTERNS
BRICK VENEER WITH STEEL FRAME CONSTRUCTION
HEAD
JAMB
SILL
JAMB
NOTE:The above wall sections represent typical wall conditions, these details are not intended asinstallation instructions. Please refer to the installation instructions provided with the purchased units.
FrameSize
Fra
me
Siz
e
Ma
son
ryO
pe
nin
g
Ro
ug
hO
pe
nin
g
MasonryOpening
RoughOpening
1/4�(6)
1/2�(13)
1/2�(13)
1/2�(13)
1/4�(6)
1/4�(6)
Scale 3� = 1� 0�
8.162014−04−28 Integrity Architectural Detail Manual11708532
SLIDING PATIO DOOR
INSTALLATION SUGGESTION
WOOD SIDING WITH 2X6 FRAME CONSTRUCTION
HEAD
JAMB
SILL
JAMB
NOTE:The above wall sections represent typical wall conditions, these details are not intended asinstallation instructions. Please refer to the installation instructions provided with the purchased units.
FrameSize
RoughOpening
1/2�(13)
1/2�(13)
Fra
me
Siz
e
Ro
ug
hO
pe
nin
g
1/2�(13)
Scale 3� = 1� 0�
8.172014−04−28 Integrity Architectural Detail Manual11708532
SLIDING PATIO DOOR
INSTALLATION SUGGESTION
STUCCO WITH 2X4 FRAME CONSTRUCTION
HEAD
JAMB
SILL
JAMB
NOTE:The above wall sections represent typical wall conditions, these details are not intended asinstallation instructions. Please refer to the installation instructions provided with the purchased units.
FrameSize
RoughOpening
1/2�(13)
1/2�(13)
Fra
me
Siz
e
Ro
ug
hO
pe
nin
g
1/2�(13)
Scale 3� = 1� 0�
8.182014−04−28 Integrity Architectural Detail Manual11708532
SLIDING PATIO DOOR
INSTALLATION SUGGESTION