PACKAGE CONTENTS Part A E C G H I J K M B F D Description Nipple Lock Washer Canopy Lock Ring Fixture Chain Ceiling Canopy Fixture Assembly Candle Cover Crossbar Green Ground Screw Hex Nut Canopy Chain Loop Quantity 1pc 2pcs 1pc 1pc 2pcs 1pc 1pc 1pc 1pc 1pc 9pcs 1pc 1pc INSTRUCTION SHEET IS-RCE5009CS01 STYLE NUMBER RCE5009CS01 : ISSUED 01-2009 Revised 2009-10-12 6 CORPORATE PARKWAY GOOSE CREEK SC 29445 www quoizel com , . . . A B C E D F G H I J L: M: WARNINGS AND CAUTIONS ! WARNING: ● Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by switching off the circuit breaker or removing the fuse. CAUTIONS: ● These instructions are provided for your safety. It is very important that they are read completely before the installation of your fixture. We strongly recommend that a professional electrician install the fixture. ● Disconnect fixture from the power source before replacing the bulb(s), making sure the bulb(s) had sufficient time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may result. 1 OF 6 A)- Crystal A 36 pcs (M1922HK) [ ] Bead Kit 1 A)- Bead String A 30 pcs B)- Bead String B 27 pcs C)- Bead String C 3 pcs D)- Bead String D 30 pcs E)- Bead String E 6 pcs F)- Bead String F 6 pcs G)- Bead G 18 pcs H)- Bead H 12 pcs I)- Bead I 18 pcs J)- Pliers [1 pc] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] A) B) C) D) A) K E) F) L J) G) H) I) Note: The BEAD KIT(S) is for replacement identification only.
IS-RCE5009CS01.cdrISSUED 01-2009 Revised 2009-10-12
, . . .
A
B
C
E
D
F
G
H
I
J
L:
M:
WARNINGS AND CAUTIONS! WARNING: Before beginning the installation,
turn off electricity at the circuit breaker box or the main fuse
box by switching off the circuit breaker or removing the fuse.
CAUTIONS: These instructions are provided for your safety. It is
very important that they are read completely before the
installation of your fixture. We strongly recommend that a
professional electrician install the fixture. Disconnect fixture
from the power source before replacing the bulb(s), making sure the
bulb(s) had sufficient time to cool down. DO NOT subject the lamp
to any shock while lit as shattering of lamp may result.
1 OF 6
A)- Crystal A 36 pcs (M1922HK)[ ]
[ ] [ ] [ ] [ ] [ ] [ ]
[ ] [ ]
[ ]
INSTALLATION INSTRUCTIONS
PREPARATION
- ,
Outlet Box Screw
STEP 1: a Secure the Crossbar onto the Outlet Box with Outlet
Box Screws Tighten until snug .
. .
STEP 2: Plier is required on this step
* . . .
. . ,
. .
.
Hex Nut
Fixture Loop
STEP 3: a Adjust the Fixture Chain to your desired length by
removing the links if needed Please note that depends on chain
material thickness
you might be required to use chain pliers to spread links
open
b Pull the supply wires through the Fixture Chain alternating links
And then pull the wires through the following components in turn
Canopy Lock Ring Ceiling Canopy Canopy Chain Loop, Lock Washer and
Nipple
c Place Lock Washer over the end of the Nipple and thread the
Canopy Chain Loop onto the end of the Nipple
d Using plier thread the Hex Nut against the Canopy Chain Loop and
tighten until snug
e Attach one end of the Fixture Chain onto the Fixture Loop and
attach the another end of the chain onto the Canopy Chain
Loop
f Refer to Step 4 Wire Connections to connect wires g Push the
Ceiling Canopy upward over the Outlet Box h Thread the Canopy Lock
Ring onto the Canopy Chain Loop
and tighten until snug to secure the Ceiling Canopy
. .
* ,
. .
. : , ,
, . .
. . ,
. .
. . - . . . .
.
.
. ( )
. ( ) ( ).
. .
Use Wire Connectors not supplied to connect the wires a Connect the
House Ground Wire to the Fixture Ground
Wire. b Connect the House White Wire to the Fixture Supply
Wire
White or Ribbed Side . c Connect the House Black or Red Wire to the
Fixture
Supply Wire Black or Smooth Side d Wrap each connection with
approved electrical tape and
carefully stuff all of the connected wires into the Outlet
Box
STYLE NUMBER RCE5009CS01:
4 OF 6
STEP 5: (For Replacement Purpose) a Begin by attaching one end of
Bead String A to every loop on the top ring of Band B Attach the
other
end of Bead String A to corresponding position on bottom ring of
Band A b Attach one end of Bead String C to loops on Support Arms
on Band B. Attach the other end of Bead
.
.
. .
.
Leaf
Bead String D
Line up Sockets on Band B to 3rd loop from Spokes on Band C.
Band B
Band C
STYLE NUMBER RCE5009CS01:
STEP 7: a Install correct Bulbs referring to fixture markings
and/or labels for maximum wattage.
.
STEP 6: a Place Candle Covers over Sockets as shown..
Candle Cover
INSTALLATION INSTRUCTIONS
c Attach Bead String B onto rest loops on the top of Band C. Attach
the other end of Bead String B to the corresponding Loops on the
bottom of Band B.
d. Attach one end of Bead String D to every loop on the top ring of
Band D. Attach the other end of Bead String D to the corresponding
positions on the bottom of Band C.
e Attach 6 Beads H to every Leaf on the top ring of Band A. f
Attach the rest Beads H to the 3rd loop from Sockets on the bottom
of Band C. (See ) g. Attach Bead String E to Bead H on the Leaves
on Band A. h. Attach the middle loop on Bead Strings F to Loops on
Support Arms of Band C. And then attach the rest
loops on Bead String F to Beads H attaching on the bottom of Band
C. i. Attach Bead G to every Bead H, Bead String F and loops on
Support Arms. j. Attach Bead I to every Loop on the bottom of Band
D. j. Attach Crystal A to every Bead G and Bead I. k. Bead String
A, B(or C) & D should hang parallel to the center stem of the
fixture If the strings are
.
. .
. , .