Instruction Manual Econo Floss and Floss Boss

© 2018 Gold Medal Products Co. Part No. 110061

Instruction Manual

10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA

Econo Floss® and Floss Boss®

Model No. 3017-00-000 and 3024-00-000

Model3024‐00‐000

Model3017‐00‐000

Econo Floss and Floss Boss Model No. 3017-00-000 and 3024-00-000

Page 2

gmpopcorn.com

SAFETY PRECAUTIONS

DANGERMachine must be properly grounded to prevent electrical shock to personnel. Failure to do so could result in serious injury, or death. DO NOT immerse any part of this equipment in water. DO NOT use excessive water when cleaning. Keep cord and plug off the ground and away from moisture. Always unplug the equipment before cleaning or servicing. Make sure all machine switches are in the OFF position before plugging the equipment into the receptacle.

008_051514

DANGERImproper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death. Any alterations to this equipment will void the warranty and may cause a dangerous condition. This appliance is not intended to be operated by means of an external timer or separate remote-control system. NEVER make alterations to this equipment. Read the Installation, Operating, and Maintenance Instructions thoroughly before installing, servicing, or operating this equipment.

014_020416

WARNINGFloss head rotates at high speeds. Operator MUST keep hands and face clear of the floss head to avoid injury. Operator must wear eye protection. Keep all spectators at a reasonable distance, and use a Floss Bubble for added customer protection.

015_062714

WARNINGKeep all foreign objects out of floss head. To avoid eye injury, DO NOT fill floss head with sugar while the head is on and rotating.

016_010914

WARNINGBurn Hazard. DO NOT touch spinner head. Allow to cool before cleaning or servicing. Avoid contact with molten sugar.

006_092414

WARNING

ALWAYS wear safety glasses when servicing this equipment.

010_010914


Page 3

gmpopcorn.com

SAFETY PRECAUTIONS (continued)

WARNINGNo user serviceable parts inside. Refer servicing to qualified service personnel.

011_051514

WARNINGRead and understand operator’s manual and all other safety instructions before using this equipment. To order copies of the operator’s manual go to gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive, Cincinnati, OH 45241 USA 1-(800)-543-0862

022_060215

WARNINGDO NOT allow direct contact of this equipment by the public when used in food service locations. Only personnel trained and experienced in the equipment operation may operate this equipment. Carefully read all instructions before operation.

012_010914

WARNING

This machine is NOT to be operated by minors.

007_010914

Note: ImprovementsarealwaysbeingmadetoGoldMedal’sequipment.Thisinformation

maynotbethelatestavailableforyourpurposes.ItiscriticalthatyoucallGoldMedal’sTechnicalServiceDepartmentat1‐800‐543‐0862foranyquestionsaboutyourmachineoperations,replacementparts,oranyservicequestions.(GoldMedalProductsCo.doesnotassumeanyliabilityforinjuryduetocarelesshandlingand/orrecklessoperationofthisequipment.)Generalimagesmaybeusedinmanualforreferenceonly.


Page 4

gmpopcorn.com

INSTALLATION INSTRUCTIONS

Inspection of Shipment Afterunpacking,checkthoroughlyforanydamagewhichmayhaveoccurredintransit.Claimsshouldbefiledimmediatelywiththetransportationcompany.Thewarrantydoesnotcoverdamagethatoccursintransit,ordamagecausedbyabuse,orconsequentialdamageduetotheoperationofthismachine,sinceitisbeyondourcontrol(referencewarrantyinbackofmanual).

Manual Readandunderstandtheoperator’smanualandallothersafetyinstructionsbeforeusingthisequipment.Toordercopiesoftheoperator’smanualgotogmpopcorn.comorwritetoGoldMedalProductsCo.,10700MedallionDrive,Cincinnati,OH45241USA1‐(800)‐543‐0862.

Model Description 3017‐00‐000:EconoFlosscottoncandymachinewithaluminumflosspan,Whirlgrip

Stabilizerand6clips.3024‐00‐000:FlossBosscottoncandymachinewithnon‐metalflosspan,Whirlgrip

Stabilizerand5clips.

Items Included with this Unit

AluminumFlossPanModel3017(PN42040)

WhirlgripFlossStabilizerModel3017(PN3010)Model3024(PN3010NM)

InstructionManual

RegistrationWarrantyCard

Non‐MetalFlossPanModel3024(PN42040NMR)


Page 5

gmpopcorn.com

Setup for Use (Generalreferenceimagesshown)

BellHousing

Lock‐N‐GoHandle

Step1:Setunitonalevelsurface.DONOTliftunitbyspinnerhead.

Step4:Checktheflossribbon(s)(heatingelement)locatedinsidetheheadassembly;makesureithasnotshakenoutofthebandduringtransportation.Ifribbonisoutofband,pushitbackintoplacemanually,beforeplugginginmachine.

Step3:Placeflosspanonunit.

Step5:InstallFlossStabilizer(seeinstructionsonnextpage).

Unitshouldbecleanedpriortouse(referenceCareandCleaningsectionofthismanual).

FlossRibbonshowncorrectlysittinginband.

Band

Step2:Lock‐N‐Go®handlesareusedfortransport.Rotatebothhandlestoavertical,UNLOCKED,positionforuse.Thisallowsthebellhousingto"float"freelyonthespringsduringoperation.DONOToperatewithhandlesinthetransportposition.

SpinnerHead


Page 6

gmpopcorn.com

Whirlgrip Floss Stabilizer

Installation Instructions UnitmustbeOFF,andcooltoinstallFlossStabilizer.PlaceFlossPanonunitandinstallWhirlGripFlossStabilizer(ItemNo.3010)asshownbelow.Kitincludes:FlossStabilizer/screening(P/N43032),and(6)WhirlgripClips(P/N77470).Clipsaredesignedtoprovideairspacebetweenscreeningandflosspan.

Step1:PlaceWhirlClipsoverrimofpanwithhooksfacinginside.

Step2:HangStabilizerontop,upfacinghook.Screeningshouldbeaboutflushwithtopofpan.

Step3:Gentlypullscreeningdownandattachtobottom,downfacinghook.

Step4:Repeatforallclipskeepingequalspacingaroundpan(numberofclipsvariesbymodel).Allowairspacebetweenpanandscreeningforproperoperation.

Allowairspaceforproperoperation.

TopViewofFlossPan


Page 7

gmpopcorn.com

Electrical Requirements Thefollowingpowersupplymustbeprovided:

3017‐00‐000and3024‐00‐000:120V~,1248W,60Hz

DANGER Machine must be properly grounded to prevent electrical shock to personnel. Failure to do so could result in serious injury, or death. DO NOT immerse any part of this equipment in water. DO NOT use excessive water when cleaning. Keep cord and plug off the ground and away from moisture. Always unplug the equipment before cleaning or servicing. Make sure all machine switches are in the OFF position before plugging the equipment into the receptacle.

008_051514

Acertifiedelectricianmustfurnishsufficientpowerforpropermachineoperationandinstallanysuppliedreceptacle.Werecommendthisequipmentbeonadedicatedandprotectedcircuit.Failuretowireproperlywillvoidthewarrantyandmayresultindamagetothemachine.ItisGoldMedalProductsCo.’srecommendationthatthismachinebepluggeddirectlyintoawalloutlet.Theuseofextensioncordsisnotrecommendedduetosafetyconcerns,andmaycausesacrificedand/orreducedperformance.Makesurecordislocatedtopreventatriphazardorunitupset.

Before You Plug In Machine 1. MakesureallmachineswitchesareOFFbeforepluggingequipmentintoreceptacle.

2. Makesurewalloutletcanacceptthegroundedplugs(whereapplicable)onthepowersupplycord.

3. Thewalloutletmusthavetheproperpolarity.Ifindoubt,haveacompetentelectricianinspecttheoutletandcorrectifnecessary.

4. DONOTuseagroundedtoun‐groundedreceptacleadapter(whereapplicable).

5. Installunitinalevelposition.

CAUTIONIf the supply cord is damaged, it must be replaced by Gold Medal Products Co., its service agent or similarly qualified persons in order to avoid a hazard.

039_080614


Page 8

gmpopcorn.com

OPERATING INSTRUCTIONS

Controls and Their Functions MOTOR&MASTERSWITCH

Twoposition,lightedrockerswitch‐turnsMotorON/OFFandsuppliespowertotheHeatSwitch.ThegreenlightONindicatesthereispowertotheunit.

HEATSWITCHTwoposition,lightedrockerswitch‐turnstheheatingelementON/OFF.ThegreenlightONindicatesthereispowertotheelement.

HEATCONTROLTheHeatControladjuststhepowertotheheatingelement.Turntheknobclockwisetoincreasepowertotheheatingelement;turncounterclockwisetodecreasepowertotheheatingelement.

Motor&MasterSwitch

HeatSwitch HeatControl

Generalcontrolsimageshownforreferenceonly.


Page 9

gmpopcorn.com

Sugar for Your Candy

ReadytoUseFlossugar

OurreadytouseFlossugaristhepreferredsugarforyournewcottoncandymachine;however100%purecaneorbeetsugarwilldojustfine.OurFlossugargivesyougoodrichcolors,andgreatflavors,too.Itispackedinhandyhalf‐gallonsealedcartons,withanE‐Zpourspoutforfillingyourmachine.Flossugarcomesinmanyflavors,andyoucaneasilychangeflavorsforgreatestvariety,andbestsales.

MixYourOwn

Ifyouwanttomixyourown,useourFlossine®,andpleasefollowourdirections.Ifyouwantadeepercolor,slightlydampenthemixedsugar.Useatablespoonofwaterperfivepoundsofsugar,sprinklewateroversugar,andmixwell.DONOTUSEEXCESSCOLOR!Toomuchcolorwillruintheelementonyourmachineandcouldcreateabittertastetothecandy.Thereisalimitastohowdarkyoucanmakecottoncandy.That’sbecausecottoncandyis98%air,andwecannotcolortheair.

SugarConsiderations

Today99%ofthesugarmanufacturedisextrafinegranulated,whichdoeshavesomesmallparticleswhichcanslipthrutheribbonswithoutbeingmelted.Ifthisbecomesobjectionable,youcanseekoutmediumcoarseorsandingsugars.Thelargercrystalsizewillrequirealittlemoreheattomelt.

Readthelabelonthebagofsugar,todayweseesomefreeflowingsugarsforrestaurants.Freeflowingsugarscontaincornstarchwhichwillburnontoyourelement/bandcloggingthemrapidly.Wehavealsoseensomeoff‐brandsugarsthatareablendofsugaranddextroseorcornsyrup.Thisproductmakesverypoorcottoncandy.Pleasemakesureyougetgoodsugarforyourcottoncandymachine.


Page 10

gmpopcorn.com

Machine Operation

Floss Machine Operation (3017 Econo Floss 3024 Floss Boss)

WARNINGFloss head rotates at high speeds. Operator MUST keep hands and face clear of the floss head to avoid injury. Operator must wear eye protection. Keep all spectators at a reasonable distance, and use a Floss Bubble for added customer protection.

015_062714

1. FollowtheguidelinesdescribedintheElectricalRequirementsSectionforsupplying

powertomachine.

2. TheHeatSwitchandtheMotor&MasterSwitchshouldbeintheOFFposition.

3. Withthespinnerheadstopped,pourflossugarintothespinnerhead.Alwaysfillit90%fullwithsugar.This90%levelisnecessarytoobtainabalancedconditionintheflosshead.DONOTOVERFILL!

IMPORTANT:NEVERaddsugarwhenmotorisrunning.

4. TurntheMotor&MasterSwitchON.Wait10seconds,andthenturnHeatSwitchON.

5. TurntheHeatControlKnobclockwisetomaximumsettingtoinitiatethefastestpossiblewarm‐up.

6. Themachineshouldstartmakingflossinabout20‐30seconds.Whenunitstartsmakingfloss,reducetheheatsetting.TurntheHeatControlcounter‐clockwisetoeliminatesmoking.Iftheunitisoperatedatthe“startup”settingitwillcarbonizetheelement.

CAUTIONNever operate the equipment for a prolonged period of time with the HEAT CONTROL in a position that causes the sugar to smoke. This will result in excessive carbonization of the heat element. If you smell burning sugar or see smoke, reduce the heat.

030_070914

7. OncetheidealHeatControlsettingisfound,operatewiththesettingnearthispositioneachtime.

8. Whentheflossheadneedstoberefilledwithsugar,ortostopthemachine,turntheHeatSwitchOFFandallowthemotortorunforafewsecondstostartcoolingdowntheflosshead,thenturntheMotor&MasterSwitchOFF.

Whencompletingoperationfortheday(oranyprolongedperiod),followtheinstructionsintheShutdownProcedure/CleaningandCaresectionofthismanual.


Page 11

gmpopcorn.com

Making Floss Pickacone,ifitsticksinthestackofcones,twistitoffthestack.

CAUTION

Keep hands away from spinning head! 031_021914

Holdaninchortwoofthepointedendofaconebetweentwofingersandathumb.Withalightflickingaction,rollconeinthewebofflossbuildingupinthepan.Lifttheconeupwiththeringofflossattachedandrotatetheconetowrapthefloss.DONOTrollflosswhiletheconeisinsidethepan.Thiswillpacktheflosstootightly.Seesteps1thru8shownbelow.

Iftheflossfailstosticktothecone,passtheconenearthespinnerheadtopickupa“starter”ofmeltedsugar.Lifttheconeoutofthepanandwraptheflosswitha"figureeight"movementofthehand.Thisleavesgiantpocketsandmakesthefinalproductappearlarger.Makesureroomhumidityisnottoohigh,orproductwillbe"heavy".

1. Gripconeasshown.

2. Breakintowebofflosswiththecone.

3. Windthesugarontothecone.

4. Liftwebofflossfromthepanandrollontothecone.

5.

6. 7.

8.

WARNING DO NOT PUT HANDS OR OBJECTS IN ROTATING SPINNER HEAD.

DO NOT FILL SPINNER HEAD WITH SUGAR WHILE IT IS ROTATING.

WEAR EYE PROTECTION.

DO NOT PUT HANDS NEAR ROTATING SPINNER HEAD.

USE FLOSS CONE TO COLLECT COTTON CANDY. 032_021914


Page 12

gmpopcorn.com

Floater Adjustments Inoperation,theflosswillcollectontheFLOSSSTABILIZER.Iftheflosscollects“low”onthestabilizer,twistthefront(leading)edgeoftheleatherfloatersdown.Yougetmoreliftandtheflosswillcollecthigher.

Formleatherfloatersasshownbelow.Thiscreatesaliftingactiontofloattheflosshigheronthewalloftheflosspan.

LeatherFloater

LeadingEdgeofLeatherFloatersseentwisteddown

Rotation


Page 13

gmpopcorn.com

Shut Down Procedure/ Care and Cleaning

Shut Down Procedure 1. Whencompletingoperationfortheday(oranyprolongedperiod),runtheflosshead

completelyemptyofsugar.

2. TurntheHeatControldialtothemaximumposition,andallowthemachinetorunapproximately3‐4minutes.Thiswillburnanyexcesssugaroutoftheflosshead,andpreventanyexcesscarbonbuild‐up.

3. TurntheHeatSwitchOFFandallowthemotortorunfor1‐2minutesto“cooldown”theflosshead.

4. TurntheMotor&MasterSwitchOFFandallowthemotortocometoaCOMPLETEstop.

5. NEVERputwaterintheflosshead.

Care and Cleaning

DANGER Machine must be properly grounded to prevent electrical shock to personnel. DO NOT immerse in water. DO NOT clean appliance with a water jet. Always unplug the equipment before cleaning or servicing.

025_111616

WARNINGBurn Hazard. DO NOT touch spinner head. Allow to cool before cleaning or servicing. Avoid contact with molten sugar.

006_092414

Goodsanitationpracticedemandsthatallfoodpreparationequipmentbecleanedregularly(onlyusenon‐toxic,foodgradecleaners).Acleanlooking,well‐keptmachineisoneofthebestwaysofadvertisingyourproduct.

Followthedirectionsbelowtocleanandsanitizetheuniteachdayafteruse.

1. Unplugthemachineandwaitfortheflossheadtocooldowntoroomtemperature.

2. Makesuretocleanallpans/accessoriesinordertosanitizethembeforeeachuse.

3. Wipeallsurfaceswithaclean,dampcloth.

4. Wipethestainlesssteelpartswithacleanclothandcleanerdesignedforstainlesssteel,suchasGoldMedalWatchdogStainlessCleaner(ItemNo.2088).

DONOTuseovencleanersorabrasivematerialsastheywilldamagepartsofmachine.


Page 14

gmpopcorn.com

Floss Bands and Ribbons GoldMedalFlossBandsaredesignedtogivelonglifeandtrouble‐freeservicewithlittlecare.DONOTscratchtheband.GoldMedalFlossRibbons(heatelements)aremadeofnickelwirewithinsulationattheterminalpointandontheleadwires.Theyaredesignedtobeasreliableasthebands;however,theribbonsmustbehandledcarefully.DONOTstretchtheribbonoritwillnotfunctionproperly.

Disassembly and Removal of Floss Band

1. Unplugthemachinefromthepowersourceandallowflossheadtocoolcompletely.

2. Removeallsugarfromtheheadofthemachinebeforedisassembling.Ifneeded,carefullyturnthemachineonitssideandshakethesugarout.

3. Removethefourspinnercapretainerscrewsandspinnercap.Insomecases,thesugarhascausedthecapandbandtosticktogether.Applyinggentlepressurewiththeheelofthehandshouldfreethepartsforremoval.

4. Removethenylonacornnut,locknut,andterminalguard.

5. Removetheelementleadwireretainingscrews(usinga1/4”(9.5mm)nutdriver),whichfastentheelementleadwirestotheterminals.Thiswillallowthebandandribbon(s)toberemoved.DONOTPULLORSTRETCHRIBBON(S)TOREMOVE.(Seenextpageforreconnectingelementleads.)

6. Ifthereisexcessivesugarbuildup,soakthebandandribbon(s)inhotwateruntilthesugardissolves.Whenthesugarhasbeenremoved,tapthebandinthepalmofyourhandtoloosentheribbon(s)forremoval.

SingleRibbonView

FlossBand

ElementLeadWireandRetainingScrews

FlossRibbon(HeatingElement)

DoubleRibbonView

NylonAcornNut

LockNut

TerminalGuard

Generalimagesshownforreference,Modelsmayvary.

Referencenextpageforreassemblyinstructions.


Page 15

gmpopcorn.com

7. Inspect,thencleanorreplacethebandandribbon(s).Theprimaryreasonforribbonreplacementiscarbonbuildupinsidetheribbon;anadditionalhotwatersoakmayhelpremovesomeofthecarbonbuildup.

8. Whenthesugarhasbeenremoved,allowthebandandelement(s)toairdryovernight.

Note:Formodelswithseparateheatandmotorswitches,thebestwaytodrytheflossheadafterreassemblyistospinitdryfor10minutesWITHOUTHEAT(usemotorswitchonly).

Reassembly of Floss Band – Units with Terminal Assemblies 1. Reinstallbandandribbon(s)onthespinnerhead;ALWAYSattachoneribbonelement

leadtoeachterminalassembly(seeimagebelow).

2. Reassembleterminalguard,locknut,andnylonacornnut.

3. Whenreinstallingthespinnercap,DONOTOVERTIGHTENSCREWS.Initiallysnugdowneachscrewevenly,becarefulnottooverapplypressureonanysinglepointandcrackthebandcoating.Oncesnug,tightenallscrewsevenlytosecurespinnercaptoflosshead.

TerminalAssemblies

INCORRECT

DONOTconnectbothribbonelementleadstothesameterminalassembly.

CORRECTConnectONEribbonelementlead

toEACHterminalassembly.

Generaldoubleribbonviewshownforreference,Modelsmayvary.

DoubleRibbonFlossHeadwithTerminalAssemblies


Page 16

gmpopcorn.com

Troubleshooting

Issue PossibleCause SolutionLowProduction A. Excessivecarbononthe

element.A. Followtheinstructionsforremovingand

cleaningbandandelement(seeFlossBandandElementsection).

B. HeatControl B. AdjusttheHeatControlKnobtoincreaseproduction.Ifthisdoesnotcorrecttheissue,havequalifiedservicepersonnelchecktheheatcontrolforcorrectvoltageoutput.AfaultyheatcontrolwillneedtobereplacedbyQualifiedServicePersonnel.

C. Lowlinevoltage. C. Checkthe wall linevoltage(wherethemachineispluggedin),atleast115VACisrequiredforthemachinetogenerateflosscorrectly.Aprimaryreasonforlowproductionandpoorequipmentperformanceislowlinevoltage.Haveaqualifiedelectriciancheckthelinevoltageandaddnewlinesforallthevariousequipmentpluggedintotheelectriccircuitifthereisnotenoughcurrentfortherequirementlistedontheequipmentnameplate.

Theuseofextensioncordsisnotrecommendedduetosafetyconcerns,andmaycausesacrificedand/orreducedperformance.Iftheuseofanextensioncordcannotbeavoidedthenbesureitisnolongerthan10to12ft.,andisatleast14AWGwire.

D. Foreignobjectsinthespinnerhead.

D. Foreignobjectsintheheadassemblycanshortoutanelementorcauseanout‐of‐balancecondition.

ExcessiveSmoke A. HeatControlsetting. A. Afterwarmup,equipmentshouldmakegoodfloss.Neverletthemachineoperatewiththeheatsohighitproducessmokeoryoucansmellburnedsugar.Thisconditionquicklyfillstheelementwithcarbonizedsugar.

Ifadjustingtheheatcontrol(andcheckingtheotheroptionslisted)doesnotcorrecttheissue,haveQualifiedServicePersonnelchecktheheatcontrol.

B. Productmixture. B. Checktheproductmixturebeingused.Forbestresults,usenothingwithacornstarchbase.

C. Excessivesugarbuildup. C. CheckthebandforexcessivesugarbuildupandremoveifneededasdescribedintheFlossBandandElementsectionofthismanual.


Page 17

gmpopcorn.com

Issue PossibleCause SolutionExcessiveVibration A. Packingmaterialnot

removed.A. Iftheequipmentisnew,checkthatallpacking

materialswereremovedfromthemachine.

B. Lock‐N‐GoHandlesnotinoperatingposition.

B. VerifythattheLock‐N‐GoHandleshavebeenrotatedintotheoperatingposition.

C. Lowonsugar. C. Refilltheflosshead;thiswillnormallyeliminateexcessivevibration.Whenaddingsugartotheflosshead,alwaysfillit90%fulltoobtainabalancedconditionintheheadandeliminatevibration.Donotaddsugarwiththemotorrunning!

D. Foreignobjectsorsugarlumps.

D. Runthesugarcompletelyout,thencheckforforeignobjectsorsugarlumpsintheheadassembly.

E. Stretchedorunevensuspensionsprings.

E. Ifthesuspensionspringsarestretchedoruneventhiscancauseunwantedvibrations.HaveQualifiedServicePersonnelreplaceifneeded.

Lock‐N‐GoHandlesareHardtoRotate

A. ClampingCamfriction. A. Ifhandlesarehardtomove,QualifiedServicePersonnelmayneedtoapplyPetroGel(GoldMedalItemNo.1110),orafoodsafelubricant,tothetopsurfaceoftheClampingCamtoreducefrictionwherethecamcontactsthebellhousing.


Page 18

gmpopcorn.com

MAINTENANCE INSTRUCTIONS

DANGERMachine must be properly grounded to prevent electrical shock to personnel. Failure to do so could result in serious injury, or death. DO NOT immerse any part of this equipment in water. DO NOT use excessive water when cleaning. Keep cord and plug off the ground and away from moisture. Always unplug the equipment before cleaning or servicing. Make sure all machine switches are in the OFF position before plugging the equipment into the receptacle.

008_051514

DANGERImproper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death. Any alterations to this equipment will void the warranty and may cause a dangerous condition. This appliance is not intended to be operated by means of an external timer or separate remote-control system. NEVER make alterations to this equipment. Read the Installation, Operating, and Maintenance Instructions thoroughly before installing, servicing, or operating this equipment.

014_020416

WARNINGNo user serviceable parts inside. Refer servicing to qualified service personnel.

011_051514

CAUTION THE FOLLOWING SECTIONS OF THIS MANUAL ARE INTENDED ONLY FOR QUALIFIED SERVICE PERSONNEL WHO ARE FAMILIAR WITH ELECTRICAL EQUIPMENT. THESE ARE NOT INTENDED FOR THE OPERATOR.

027_010914


Page 19

gmpopcorn.com

ORDERING SPARE PARTS 1. Identifytheneededpartbycheckingitagainstthephotos,illustrations,and/or

partslist.(Generalimagesmaybeusedinmanualforreferenceonly.)

2. Useonlyapprovedreplacementpartswhenservicingthisunit.

3. Whenordering,pleaseincludepartnumber,partname,andquantityneeded.

4. Pleaseincludeyourmodelnumber,serialnumber,anddateofmanufacture(locatedonthemachinenameplate/dataplate)withyourorder.

5. Addressallpartsordersto:

PartsDepartmentGoldMedalProductsCo.10700MedallionDriveCincinnati,Ohio45241‐4807Or,placeordersbyphoneoronline:Phone: (800)543‐0862

(513)769‐7676Fax: (800)542‐1496

(513)769‐8500E‐mail:[email protected]:gmpopcorn.com


Page 20

gmpopcorn.com

Cabinet Exterior and Lock-N-Go Handle Assembly

*CAUTION:Ifsupplycordisdamaged,itmustbereplacedbyGoldMedalProductsCo.,itsserviceagent,orsimilarlyqualifiedpersonsinordertoavoidahazard.

26,27

28,29

30,31

24

23

25

22*

13

14

11,12

1921 20 18 17

15

16

3

7

2

5

1

6 4

9

10

8


Page 21

gmpopcorn.com

Cabinet Exterior and Lock-N-Go Handle Assembly – Parts List

Item PartDescriptionPartNumber

3017‐00‐000 3024‐00‐000

1SPINNERHEAD,COMPLETE5IN(CompleteAssy.)SeeSpinnerHeadAssemblysectionforindividualpartsbreakdown.

42283 42283

2BRUSHHOLDERASSY(includesBrushes,CapsandHolders)SeeBrushAssemblyBreakdownsectionforindividualpartsbreakdown.

42382W 42382W

3 BELLHOUSING,DUALBRUSH 42190 421904 LABEL,FLOSSADVERTISEMENT 42159 421595 BOWL,SEALRETAINER 56561 565616 BELLHOUSINGSEAL 56571 565717 THREADEDBUMPER,1/4‐20 102017 1020178 NAME,INSTRUCTIONOVERLAY 102027 1020239 SWITCH,LIGHTEDROCKERGR 42798 4279810 KNOB,HEATCONTROL 42556 4255611 10‐24X1/2PHTRUSSM/S 42826 4282612 HEXNUT#10‐24ESLOK 74691 7469113 RUBBERFEET3/4INHIGH(4required) 47155 4715514 HANDLEUNLOCKDECAL 102253 10225315 LOCKNGOHANDLE,NEWCAB. 56563 5656316 5/16‐18X1/2PHTRM/S 12183 1218317 WASHERSS.5IDX1.10OD 48428 4842818 CLAMPINGSHAFT,LOCKNGO 56565 5656519 CLAMPINGCAM 42460 4246020 5/16FLATWASHERZINCPLT 74134 7413421 HEXNUT5/16‐18ESLOK 12001 1200122* POWERSUPPLYCORD 22038 2203823 STRAINRELIEFSR‐6P3‐4 76026 7602624 WARNINGLABELCORD 68720 6872025 8‐32X3/8PHILPANHEAD 87515 8751526 1/4‐20X3/4GRADE5BOLT(w/LockWasher) 74520 7452027 TINNERMANNUT1/4‐20 42125 4212528 8‐32X3/8SLT.HWHM/S 42044 4204429 #8‐32TINNERMANFASTENER 47299 4729930 INSPECTIONBRUSHCOVER 42381 4238131 LABEL,CLEANEVERY500LBS 42002 42002


Page 22

gmpopcorn.com

5” Ribbon Spinner Head (Model No. 42283)

16

17

*UsestwoSetScrews

19

20

21

22*

14 15 8

23

18

SpinnerHeadBottom

431 2

13

FlossHead–BandInteriorView

SpinnerHeadComplete(Model42283)

56

7

8

9

10

11

12


Page 23

gmpopcorn.com

5” Ribbon Spinner Head (Model No. 42283) – Parts List


422831 LEATHERFLOATER 200102 SCREW8‐32X5/16PHPANMS 892473 HIGHCAPACITYSPINNERCAP 431664 10‐24X2PHIL/SLTMS 420415 51/2FLOSSBAND 431656 11OHMRIBBONASSEMBLY 422517 1/4–20NYLONACORNNUT 480418 1/4–20SERRATEDLOCKNUT 463119 PHENOLICTERMINALGUARD 4216210 8‐32X1/2FLHDPHMS 2006611 BALANCEWEIGHT 4342212 8‐32X1/4HXHDWHIZLOCK 42045

13SPINNERHEADBOTTOM(Completeassemblyincludes2elementleadscrews,TerminalGuard,NylonNut,LockNut,anditemslistedbelow.)

42284

14 UPPERSPINNERHEAD 4243715 1/4‐20X2‐3/4SETSCREW 4241316 HEXNUT#10‐32BRASS 4230117 #10INTERNALTOOTHWASHER 1257318 TERMINALASSEMBLY 4230519 SLIPRINGSTUD 4212720 SLIPRINGMACHINED 42126HD21 LOWERSPINNERHEAD1/2 42281

22SETSCREW1/4‐20X3/8(2requiredfortheLowerSpinnerHead)

74125

23 BOTTOMPHENOLICWASHER 20054


Page 24

gmpopcorn.com

Bell Housing Interior – Brush Assembly

Item PartDescriptionPartNumberAllModels

1 HEXNUT#10‐24ESLOK 746912 .188IDFLATWASHER 770523 MOTORMTGPLATE 421194 MOTOR,FLOSSMACHINE 486495 6‐32X1/2PHPANHDM/S 475166 6‐32GRIPNUTZINCPLATED 47517

7BRUSHHOLDERASSEMBLY(includesBrushes,CapsandHolders)

42382W

8 DUALBRUSHHOLDERW/LEADS 42436W9 CARBONBRUSH 5500710 CAP,BRUSHHOLDER 42138

9

10

8

7

4

3

1,2

5,6


Page 25

gmpopcorn.com

Cabinet Interior – Parts Breakdown

11

12

13

14

Whenreassemblingtheunit: BesuretheBellHousingislocatedUNDERtheClampingBracketsasshownhere.

Besuretokeepwiringclearofthelockingmechanism.

3

2

1

8

9,10

4,7

6

4,5

3024‐00‐000

Generalimageshownforpartsreferenceonly.


Page 26

gmpopcorn.com

Cabinet Interior - Parts List

Item PartDescriptionPartNumberAllModels

1 MOTOR,FLOSSMACHINE 486492 SWITCH,LIGHTEDROCKERGR 427983 ELECTRONICHEATCONTROL 425584 6‐32X3/8PHILPANM/S 390005 WASHER#6INTERNALTOOTH 761886 RELAY,120VAC,DPST‐NO 485907 6‐32GRIPNUTZINCPLATED 475178 TERMINALBLOCK,2POS 556209 8‐32X3/4PHILPANMSSS 3900710 HEXNUT#8‐32STAINLESS 8912911 ACORNNUT1/4‐20 4906812 SPRING,SUSPENSIONMEDIUM 4252413 SCREW1/4‐20X3/8PNHDPH 4236014 10‐24TINNERMAMFASTENER 42221

Floss Pan and Whirlgrip Stabilizer


3017‐00‐000 3024‐00‐0001 FLOSSPAN(aluminum) 42040 2 FLOSSPAN(non‐metal) 42040NMR

3WHIRLGRIPSTABILIZER(IncludesFlossStabilizerandClips)

3010 3010NM

4 FLOSSSTABILIZER(Web) 43032 43032NM5 WHIRLGRIPCLIPS 77470 77470

WhirgripStabilizer(includesFlossStabilizerandClips)

13

5

4

2


Page 27

gmpopcorn.com

Wiring Diagram

Model No. 3017-00-000 and 3024-00-000


Page 28

gmpopcorn.com

© 2018 – The text, descriptions, graphics, layout, and other material in this publication are the exclusive property of Gold Medal Products Co. and shall not be used, copied, reproduced, or published in any fashion, including website display, without its express written consent.

WARRANTY Gold Medal Products Co. warrants to the original purchaser each item of its manufacture to be free of defects in workmanship and material under normal use and service. Gold Medal Products Co.’s obligation under this warranty is limited solely to repairing or replacing parts, f.o.b. Cincinnati, Ohio, which in its judgment are defective in workmanship or material and which are returned, freight prepaid, to its Cincinnati, Ohio factory or other designated point. Except for “Perishable Parts” on specific machines, the above warranty applies for a period of two (2) years from the date of original sale to the original purchaser of equipment when recommended operating instructions and maintenance procedures have been followed. These are packed with the machine. Parts warranty is two (2) years, labor is six (6) months.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR PART, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. In no event shall Gold Medal Products Co. be liable for special, incidental or consequential damages. No claim under this warranty will be honored if the equipment covered has been misused, neglected, damaged in transit, or has been tampered with or changed in any way. No claim under this warranty shall be honored in the event that components in the unit at the time of the claim were not supplied or approved by Gold Medal Products Co. This warranty is effective only when electrical items have been properly attached to city utility lines only at proper voltages. This warranty is not transferable without the written consent of Gold Medal Products Co.

The term “Original Purchaser” as used in this warranty shall be deemed to mean that person, firm, association, or corporation who was billed by the GOLD MEDAL PRODUCTS CO., or their authorized distributor for the equipment.

THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS CO. AT 1-800-543-0862 TO DISCUSS WITH OUR SERVICE REPRESENTATIVE THE EQUIPMENT PROBLEM, AND, IF NECESSARY, FOR INSTRUCTIONS CONCERNING THE REPAIR OR REPLACEMENT OF PARTS.

NOTE: This equipment is manufactured and sold for commercial use only.

10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA gmpopcorn.com

Phone: (800) 543-0862 Fax: (800) 542-1496 (513) 769-7676 (513) 769-8500

Documents

Instruction Manual Econo Floss and Floss Boss