Instruction Manual Controll-A-Door Power Drive · Controll-A-Door® ®Power Drive & Roll-A-Pro Instruction Manual 3 1. Installation Safety Warnings! WARNING! •he door may operate

1Controll-A-Door® Power Drive & Roll-A-Pro® Instruction Manual

Controll-A-Door® Power Drive& Roll-A-Pro®

Doc #: 161040_03Part #:79129Released: 20/11/18

Rolling Door Opener

Instruction Manual

Controll-A-Door® Power Drive & Roll-A-Pro® Instruction Manual2

Table of Contents

1. Installation Safety Warnings! 32. Kit Contents 43. Tools Required 44. Setup Requirements 5

The Opener: 5Unsuitable Door Types 5Sideroom 5

5. Door Preparation 66. Fit the Weight Bar 6

If the door has a handle: 6If the door does not have a handle: 6

7. Pinning the Door 78. Proping the Door 79. Mounting the Opener 810. Setting the Travel Limits 9

Initial Preparation: 9Set the Limit Positions: 9Resetting the Door Limit Positions 9Setting the PET Mode position 9Reset all Factory Defaults 9

11. Safety Testing 10Test the Close Cycle 10Testing the Open Cycle 10Test the Manual Door Operation 10Adjusting Safety Obstruction Force 10To Increase Force Pressure 10To Decrease Force Pressure 10To Recall Factory Set Force 10To Recalculate Force Margins 10

12. Accessories 11Auxiliary Output 11Keyswitch Connection 11Remote Aerial 11

13. Auto-Close (CAD PD Only) 11Safety Beams 11Auto Close Option 11

14. Coding a Transmitter 12Storing the Transmitter Code 12Coding a Transmitter to the Courtesy Light 12Coding Vacation Mode 12Coding to enable AUX Output 12Setting the Transmitter to Operate PET Mode 13Installation of the Wall Mounted Transmitter 13Remotely Coding Transmitters 13Erasing Programmed Codes 13

Installation Instructions

Home Owner Instructions15. Home Owner Safety Warnings! 1416. Opener Safety & Security 15

Your Door CAN NOT be used when: 15Your Door CAN be used when: 15To Disengage the Opener: 15To Re-Engage the Opener: 15

17. Operating your Opener 1518. User Operating Controls 1619. Door Status Indicators 1620. Specifications 1721. Troubleshooting 1822. Maintenance 2023. Battery Replacement 2024. Battery Disposal 2025. Service Schedule 2126. Warranty 2227. Optional Accessories 23


1. Installation Safety Warnings!

WARNING! • The door may operate unexpectedly, therefore do not allow anything to stay in the path of the door.

• When operating the manual release while the door is open, the door may fall rapidly due to weak or broken springs, or due to being improperly balanced.

• The drive must not be used with a door incorporating a wicket door, unless the drive cannot be operated with the wicket door open.

• The drive is intended to be installed at least 2.5m above the floor.• Do not disengage the opener to manual operation with children/persons or any

objects including motor vehicles within the doorway.• If the door is closing and is unable to re-open when obstructed, discontinue use.

Do not use a door with faulty obstruction sensing• When using auto close mode, a Photo Electric beam must be fitted correctly and

tested for operation at regular intervals. Extreme caution is recommended when using auto close mode. All safety rules must be followed.

ELECTROCUTION! • Place opener in protected area so that it does not get wet.• Do not spray with water .• Disconnect the power cord from mains power before making any repairs or removing

covers. Only experienced service personnel should remove covers from the opener.• If the power supply cord is damaged, it must be replaced by an Automatic

Technology service agent or suitably qualified person.• Connect the opener to a properly earthed general purpose 240V mains power

outlet installed by a qualified electrical contractor.

CAUTION:Emergency Access • If garage has no pedestrian entrance door, an emergency access device should

be installed. This accessory allows manual operation of the garage door from outside in case of power failure.

Muscular strain • Practice correct lifting techniques (carton weighs approx 9kgs)• Practice correct lifiting techniques when required to lift the door as per installation

instructions.Fall from ladder • Ensure ladder is the correct type for job.

• Ensure ladder is on flat firm ground that will take the weight without the legs sinking.• Ensure user has 3 points of contact while on ladder.

Crush injury from unsecured door

• Place a 2 metre exclusion zone around area under the door while it is unsecured.• Do not move under a door while it is on the door support (or ladder)• Follow the installation instructions• Fit door support (or ladder) snugly under door before removing bracket.• Ensure door support (or ladder) is on flat ground

Garage Door • Examine the door installation, in particular, springs and mountings for signs of wear, damage and imbalance.

• The garage door must be well balanced. Sticking or binding doors must be repaired by a qualified garage door installer prior to installation of the opener.

• Remove or disengage all garage door locks and mechanisms prior to installation of the opener.

Entanglement • Never plug in and operate opener prior to installation.• Keep hands and loose clothing clear of door and guides at all times.

Entrapment under operating door

• DO NOT operate the opener unless the garage door is in full view and free from objects such as cars and children/people. Make sure that the door has finished moving before entering or leaving the garage

• In order for the opener to sense an object obstructing the door way, some force must be exerted on the object. As a result the object, door and/or person may suffer minor damage or injury.

• Ensure the garage door is in good working order by undertaking regular servicing.• Install the optional wall transmitter in a location where the garage door is visible,

but out of the reach of children at a height of at least 1.5m.• Photo Electric beams must be installed if the closing force at the bottom edge of the

door exceeds 400N (40kg)

This automatic garage door opener is designed and tested to offer safe service provided it is installed and operated in strict accordance with the following safety warnings. Failure to comply with the following instructions may result in death, serious personal injury or property damage.


2. Kit Contents

OR

1. Power Drive 1 x RDO-1V4 drive unit Roll-A-ProTM 1 x RDO-1V3 drive unit

2. 2 x Locking Bar Covers3. Power Drive 2 x TB-6 Transmitters

1 x Wall Mount Transmitter Roll-A-ProTM 3 x TB-5 Transmitters 1 x Wall / Visor Clip4. 1 x Collar Kit5. 1 x Weight Bar

Fastner Bag6. 2 x Nilock Nut7. 2 x 2 x 3/16 x 1/2 flat washers8. 2 x Pan Head Screw M4 x 509. 2 x Self Tapping Screw M10 x 3210. 2 x Washer 6.4 x 20.6 x 1.2 GAL

Accessory Pack11. 2 x Extension Fork12. 2 x Flat Washer 107D 6.4 x 20.5 x 1.613. 2 x Hex Serration Head Screw M6 x 45

1

2

3

5

6 7

8

13

12

11

9

4

10

Screwdrivers

Adjustable End Wrench

Sockets and Wrench

Pencil

RopeDrill

Towel

Screws and Washers(M10 x 32mm)

Stepladder

Door Stand or suitable prop

3. Tools Required


WARNING! A portable power generator is not recommended due to spikes, surges and fluctuations in the supply.

85

41

135

95

Minimum Side room Recommended Side room

Unsuitable Door TypesThe drive must not be used with a door incorporating a wicket door, unless the drive cannot be operated with the wicket door open. The fitting of an opener to doors with removable mullions is not recommended. SideroomThe minimum sideroom required from the edge of the door curtain is 41mm to the inside of the door bracket, and 85mm to the wall. If a Battery Backup is to be fitted, at least 135mm to the bracket is required.Therefore the recommended sideroom from the edge of the door curtain is 95mm to the inside of the door bracket, and 135mm to the wall as per diagram.

4. Setup RequirementsThe Opener:a. MUST BE installed in a dry position, protected from weather. (Moisture or corrosion not covered by Warranty)b. Is factory set for RIGHT HAND SIDE installation (from inside garage), but capable of LEFT HAND SIDE installation.c. REQUIRES properly earthed 3 pin single phase power within an arms length of door and at a suitable heightd. Requires a MINIMUM SIDEROOM of 41mm from the edge of the door to the inside of the door bracket and 85mm

to the wall.e. CAN NOT be installed on a Door Axle Diameter that exceeds 35mm.

LEFT HAND SIDE RIGHT HAND SIDE

40mm 40mm

85mm85mm


If the door has a handle a weight bar must be fitted to ensure the door doesn’t balloon during operation: a. Remove the door handleb. Fit the weight bar 5 and refit the handle using the two (2) M4x50mm Pan Head Screw 8 and the two (2) Flat

Washer 7 and the two (2) M4 Nilock Hex nut 6 .

If the door does not have a handle:a. Locate the centre of the door at the bottom rail.b. Place the weight bar at this point and mark the two positions where the fasteners will goc. Drill the two 4.5mm holes in the door and fit the weight bar 5 using the two (2) M4x50mm Pan Head Screw 8

and the two (2) Flat Washer 7 and the two (2) M4 Nilock Hex nut 6 .d. Check that the door is still balanced and smooth. If not, then the door may require servicing.

5

2

8

5. Door PreparationPrepare the Door:a. Clean the guides if there is any oil or wax present using a suitable white spirit. The only lubricant suitable for use on

door guides is silicon spray. DO NOT use WD-40, RP-7, petroleum grease, or similar.b. Remove the locking bars or disable the lock.c. Install the locking bar covers 2 if there are locking bar holes in the guides. This ensures fingers cannot be placed

in the holes while the door operatesd. Affix the supplied warning labels where they are clearly visible on the inside of the door.e. Install the collar kit 4 to the OPPOSITE end to where the opener is being installed. f. Fit the collar kit hard up against the drum.

6. Fit the Weight Bar

WITH HANDLE WITHOUT HANDLE

6

7

5

8

6

7

4


7. Pinning the DoorPinning the Door to the drum:Pinning the door’s curtain to its drum maintains security when the opener is closed. If the curtain is not pinned the door can be partially opened manually. a. Fully close the door.b. Mark a minimum of two (2) drill holes on the drum to each end of the

door.c. Drill holes using 3.2mm (1/8”) drill bit. d. Fit M10 x 32mm screws and washers (not supplied) to each of the

four (4) holes. This screw should be positioned as low as possible in the grove, but make sure that it does not alter the curtain’s normal lead in to the guide.

BALLOONING DOOR

PINNED DOORFREE DOOR

Without locking bars door can be

lifted

Without locking bars door can be

liftedDoor secure and will not lift

Pin Points

Screw into the low part

of grove

8. Proping the DoorPrepare the Door:a. At the end opposite to where the opener will be fitted, check that the

U-bolt which holds the door axle to the bracket is tightened securely.

b. Open the door completely and tie rope around the door roll. Do not tie the rope too tight as damage to the curtain may ensue. This will stop the door unrolling when taken off the bracket

c. At the end where the opener is to be fitted, support the door with a door stand or suitable prop. Place a towel between the door and the prop to protect the door from damage.

d. At the end where the opener will be fitted use a pencil to mark the position of the U-bolt in the door bracket and the position of the door bracket on the wall to assist in reassembling.

WARNING! The U-bolt must be done up tightly to ensure the stored energy in the springs cannot be unexpectedly released.

WARNING! Make sure the prop is snug under the door and is stable.

U-bolts

Towel

Door stand or prop

Door bracket


Raising the Door: a. When in position, remove the U-bolt (or bolts) and saddle from

the door bracket.b. Lift the door up and away from the wall until clear of the door

bracket, before lowering the door to rest on the door stand or prop.

NOTE: If there is limited ceiling space to lift the door, the door bracket may have to be removed. If this is required, when refitting the door bracket , use the reference marks on the wall for correct

9. Mounting the Opener

Lift door up, away from wall and down onto prop

WARNING! For tight sideroom installations the door may have to be taken down.

position and ensure that it is secure to the wall and will support the door.

Mounting the Opener: a. Remove the opener from the box.b. Insert the two (2) Extension forks 11 into the ring gear.

Tighten U-bolts

Pull string down to disengage opener

Slide opener over door axle

c. Secure with two (2) Flat washers 12 and two (2) Hex serration head screws 13 .

d. Check the drive gear rotates freely, by pulling the string handle down (there will be a click) to disengage opener. Then move the forks from side to side by hand.

e. Slide the opener over the door axle and into the drum of the door as shown.

f. Push the opener in as far as possible (without interfering with the curtain) so one of the door drum’s wheel spokes is between the opener’s drive forks.

g. Raise the door off the door stand or suitable prop.h. Lift up and over the door bracket and use your reference

marks on the door bracket to position the door.i. Refit the U-bolt and nuts and tighten.j. Remove the safety rope and door stand or prop.k. Connect the power cort to a suitable powerpoint, but DO NOT

switch on.l. Secure the power cord away from any moving object (e.g the

door) with the cable clip supplied.m. With the opener still disengaged, pull the door up and down

to make sure it runs freely.

13

12

11


10. Setting the Travel LimitsInitial Preparation: a. Move the door to the half way position.b. Remove the clear button cover from the unit.c. Engage the opener by pulling down on the manual

release string until a click sounds.d. Switch power on to the opener. The red CLOSE LIMIT LED

will be flashing.e. Press and hold the MINUS (-) button - the door should start

closing.NOTE: If the door opens, release the MINUS (-) button and press the OPERATE button once to change the motor’s direction.

Pull string down to engage opener

Set the Limit Positions:The Limit Positions can vary due to site conditions, such as uneven ground. When setting the Close limits, ensure the position is when the door makes first contact with the ground. Alternatively for the Open limits the position should be at the height of the garage opening.

a. Press and hold MINUS (-) button until the door reaches your desired close limit position. The rubber strip at the bottom of the door should form a good seal with the ground.

b. Release the MINUS (-) button when the door is near the desired closed position. Single presses of the MINUS (-) button will inch the door closer to the ground.

c. If the door overshoots press the PLUS (+) button to move the door in the open direction.

d. When the door is at the desired close position, press the LIMIT SET button, the OPEN LIMIT LED will now flash.

e. Press and hold the PLUS (+) button until the door reaches your desired open limit position. Single presses of the PLUS (+) button will inch the door open.

f. If the door overshoots press the MINUS (-) button to move the door in the close direction.

WARNING! In setting the close limit position, do not force the door into the floor with excessive force, as this can interfere with the ease of operation of the manual release mechanism.

g. When the door is at the desired open position, press the LIMIT SET button.

h. The door will now automatically close and open to calculate the safety obstruction settings.

Resetting the Door Limit PositionsLimit positions can be deleted by:a. Press and hold LIMIT SET button for six (6) seconds until the

CLOSE LIMIT LED flashes quickly.b. Release the LIMIT SET button.

NOTE: If no action is taken within 30 seconds, the opener will return to normal operating mode and restore the original settings.c. Follow steps a - f in Set the Limits Poisitions to set new limit

positions.

WARNING! The door will automatically close, open and close again after the next step. Ensure that nothing is in the door’s path.

Setting the PET Mode positionWhen activated, PET mode drives the door to a preset position from the close position, therefore allowing a pet or parcel to go under the door. a. Drive and stop the door at the deisred PET mode

open position by pressing the transmitter button coded for Open/Stop/Close operation.

b. Press and hold the PLUS (+) button on the opener for six (6) seconds until the OPEN and CLOSE LED’s are lit to record the new PET position.

c. Release the PLUS (+) button.

Reset all Factory Defaultsa. Turn power to the opener off.b. Press and hold the LIMIT SET Button.c. Turn power on while holding the LIMIT SET button.

Continue to hold until all LED’s are off.d. This will not erase transmitter codes stored in

memory.


11. Safety TestingTest the Close Cyclea. Press the OPERATE button to open the door.b. If the door closes, press the OPERATE button to stop the door,

then press OPERATE again to open.c. Place a piece of timber approximately 40mm high (or the

openers cardboard box) on the floor directly under the door.d. Press the OPERATE button to close door. e. The door should strike the object and re-open.f. Remove the timber or cardboard box.

Testing the Open Cyclea. Press the OPERATE button to close the door.b. Press OPERATE again to open the door. c. When the door reaches approximately half way, firmly grab

the door’s bottom rail - the door should stop.If the door does not reverse readily when closing, or stop when opening, put the door into manual by pulling down on the manual release string to diesengage the motor and contact 1300 300 625 for support.

Test the Manual Door OperationPeriodically disengage the opener and manually operate the door. The door must be smooth to operate by hand. The force required on the bottom rail should not exceed 15 kg.

CAUTION: Take care when completing a safety test. Failure to follow this warning can result in serious personal injury and/or property damage.

WARNING! If the door is closing and is unable to re-open when obstructed, discontinue use. Do not use a door with faulty obstruction sensing.

Wood 40mm high or opener cardboard box

To Recall Factory Set Forcea. Holding down the FORCE MARGIN SET button

and the LIMIT SET button for two seconds.b. Release both buttons. The default setting

should now be recalled.

To Recalculate Force Marginsa. Press and hold the FORCE MARGIN SET Button

for six (6) seconds, the beeper will sound once.b. The door will start to move and re-calculate

force margins. The door can move between the open and close limit positions up to four (4) times (depending on the position of the door and the power up condition).

c. A single beep will be heard once the process is complete.

d. Test the force again as per Testing Close Cycle and Testing Open Cycle.

Adjusting Safety Obstruction ForceThe Safety Obstruction Force is calculated automatically during setup. Adjusting this is normally only necessitated by environmental conditions such as windy or dusty areas, and areas with extreme temperature changes.

To Increase Force Pressurea. Hold down the FORCE MARGIN SET button.b. While holding the FORCE MARGIN SET button, press the PLUS

(+) button. Each press will increases the force margin. c. The OPEN LIMIT LED will flash each time the PLUS (+) button is

pressed to indicate an increase in force. d. If the OPEN LIMIT LED flashes continuously when the PLUS (+)

button is being pressed, this indicates that the maximum force setting has been reached.

e. Test the force again as per Testing Close Cycle and Testing Open Cycle.

To Decrease Force Pressurea. Hold down the FORCE MARGIN SET button.b. While holding the FORCE MARGIN SET button, press the

MINUS (-) button. Each press will decrease the force margin. c. The CLOSE LIMIT LED will flash each time the MINUS (-) button

is pressed to indicate a decrease in force. d. If the CLOSE LIMIT LED flashes continuously when the MINUS

(-) button is being pressed, this indicates that the minimum force setting has been reached.

e. Test the force again as per Testing Close Cycle and Testing Open Cycle.

WARNING! If the door fails these tests, put the opener into manual mode, only operate the door by hand and call for service.


12. AccessoriesAuxiliary OutputThe auxiliary output can be used to control alarm or another garage door opener. A valid transmission from the pre-coded transmitter will cause the auxiliary output to pulse for approximately 1 (one) second. The maximum DC voltage must not exceed 35 volts DC. Maximum current must not exceed 80 ma.

V+EB10VEB20VOSCAUX

External device, Alarm, Door or Gate opener.

V+EB10VEB20VOSCAUX

Remote AerialSome sites cause poor radio reception. Particularly problematic areas are those where there is a large amount of metal, like a steel garage, or an underground car park with large masses of steel reinforced concrete. These issues, and others, can create reception issues.Poor radio reception will be noticed by a reduction in the operating range of the transmitters.

You can evaluate whether fitting an external aerial will benefit as follows;i. Test the maximum operating range of the transmitter with the garage door closed; thenii. Test the maximum operating range of the transmitter with the garage door open.

If the range improves when the door is open you can install a remote aerial kit to improve reception.

Mount the aerial to a suitable location on the outside of the garage.Similar to a television aerial, the better the mounting position the better the reception will be. Where possible, mount the aerial as high as possible, away from masses of metal and in line of sight position, to where you normally use your transmitter.

Keyswitch ConnectionThe RDO-1V4 has the input to connect bell switch or keyswitch to open or close the door.

Safety BeamsA Safety Beam Kit may be fitted to this opener. When this option is fitted, the operation of this device is such that if an object (i.e car, child etc) blocks the Infra-Red beam, then the garage door opener will not close the door automatically. If the Safety Beam is fitted but not operating coreectly, then the door once opened automatically, will not close automatically.

Auto Close OptionAuto-Close mode is a function that automatically closes the door a preset time after the Safety Beams recognise that a vehicle has left the garage. The Auto-Close timer only starts after the Safety Beam’s path is broken. If the safety beam path is not broken, the door will remain open until the path is broken. If the opener incurs a physical obstruction (i.e. not from the Safety Beams) while closing the door, it will re-open and not Auto-Close until the Safety Beam’s path is broken again.

To enable the Auto-Close function remove the light diffuser from the opener and remove the AUTO-CLS (ACLS) shunt next to the programmer input and place over both ACLS inputs. When this option is selected the garage door opener will attempt to close the door automatically 30 seconds after opening. Refit the light diffuser.

13. Auto-Close (CAD PD Only)WARNING! It is compulsory to have Safety Beams installed when using Auto-Close mode.

Remove shunt and place over both inputs.


14. Coding a TransmitterStoring the Transmitter Code The opener can only operated from remote control transmitters that have been programmed into its memory. Up to 64 codes can be stored in the memory. a. Press the CODE SET button and release. The CODE SET LED will

illuminate to indicate the opener is in Code Learn mode. If a valid code is not stored within 15 seconds the opener will exit Code Learn.

b. Press the transmitter button one (1) to control the door. The CODE SET LED will flash.

c. Press the same transmitter button again. The CODE SET LED will illuminate for one second then go out.

d. The transmitter button is now coded - press to test.

Coding a Transmitter to the Courtesy Light The transmitter can be programmed to operate the courtesy light on the opener independently of the door moving.a. Press the CODE SET button twice - the CODE SET LED and courtesy

light will both illuminate.b. Press one of the four buttons on the transmitter for two (2) seconds,

pause for two (2) seconds, then press the same button again for two (2) seconds.The CODE SET LED will illuminate for one second then go out.

c. Press the transmitter button to test.

Coding a Transmitter Button to Enable Vacation ModeThe opener can be programmed into a “Vacation Mode” where the opener will not respond to any transmitter except the button of the transmitter that was programmed for vacation mode.a. Press the CODE SET button three (3) times - the CODE SET LED will

illuminate and the courtesy light will flash slowly.b. Press one of the four (4) buttons on the transmitter for two (2)

seconds, the CODE SET LED will begin to flash, pause for two (2) seconds, then press the same button again for two (2) seconds.

c. The CODE SET LED will illuminate for one second and then go out, and the courtesy light will also switch off. This indicates the code has been stored.

d. Press and hold the transmitter button for five (5) seconds to set Vacation Mode. The CODE SET LED will stay lit while Vacation Mode is active.

e. To reset Vacation Mode, press the same button for two seconds, until the CODE SET LED turns off.

Coding a Transmitter to enable AUX Output a. Press the CODE SET button four (4) times - the CODE SET LED will

illuminate and the courtesy light will flash quickly.b. Press one of the four (4) buttons on the transmitter for two (2)

seconds, the CODE SET LED will begin to flash, pause for two (2)

Button 1

TB-6 Shown

IMPORTANT NOTE: Only Tri-Tran+TM Technology Transmitters are compatible with these RDO-1 products.


Option not available with the TB-5 transmitters (Roll-A-Pro®)

seconds, then press the same button again for two (2) seconds. The CODE SET LED will illuminate for one second then go out.

c. Press the transmitter button to test. Setting the Transmitter to Operate PET (Pedestrian) Mode The PET mode position (see Programming the Opener) must set prior to coding a transmitter.a. Press the CODE SET button five (5) times - the CODE SET LED

will illuminate and the courtesy light will flash quicky (twice per second).

b. Press one of the four (4) buttons on the transmitter for two (2) seconds, the CODE SET LED will begin to flash, pause for two (2) seconds, then press the same button again for two (2) seconds.

c. The CODE SET LED will illuminate for one second and then go out, and the courtesy light will also switch off. This indicates the code has been stored.

d. Press the transmitter button to test.

Installation of the Wall Mounted Transmitter (RDO-1V4 Only)a. Mount the transmitter in a convenient location, yet out of reach of

children and at least 1.5m off the ground.b. Make sure the door is visible from this location.c. To set the transmitter press the CODE SET button and release. The

CODE SET LED will illuminate to indicate the opener is in Code Learn mode. If a valid code is not stored within 15 seconds the opener will exit Code Learn.

d. Press the transmitter button (one of four) that you want to control the door. The CODE SET LED will flash.

e. Press the same transmitter button again. The CODE SET LED will illuminate for one second then go out.

f. The transmitter button is now coded - press to test

Remotely Coding TransmittersUsing this method transmitters can be coded without access to the opener’s control panel as long as a pre-coded transmitter is available.a. Take any pre-coded transmitter. Press the button for the function

to be duplicated and release. b. Using a small needle / pen, press and hold firmly for two seconds

the middle button, through the Coding Hole. c. Within ten (10) seconds take the additional transmitter you wish

to code. Hold the new transmitter’s button for two seconds, pause for two seconds, hold again for two seconds and then release.

d. Wait for ten (10) seconds and then press the new transmitter’s button to test.

Erasing Programmed CodesIf the CODE SET button is pressed and held for six (6) seconds the CODE SET LED will blink rapidly for one second to indicate that all programmed codes have been erased.

CAD PD Only

14. Coding a Transmitter


B&D Doors to the extent that such may be lawfully excluded hereby expressly disclaims all conditions or warranties, statutory or otherwise which may be implied by laws as conditions or warranties of purchase of a B&D Garage Door Opener. B&D Doors hereby further expressly excludes all or any liability for any injury, damage, cost, expense or claim whatsoever suffered by any person as a result whether directly or indirectly from failure to install the B&D Garage Door Opener in accordance with the installation instructions.

Please read these important safety warnings!

This automatic garage door opener is designed and tested to offer safe service provided it is installed and operated in strict accordance with the following safety warnings. Failure to comply with the following instructions may result in death, serious personal injury or property damage.

WARNING! • When operating the manual release while the door is open, the door may fall rapidly due to weak or broken springs, or due to being improperly balanced.

• DO NOT disengage the opener to manual operation with children/persons or any objects including motor vehicles within the doorway.

• If the door is closing and does not re-open when obstructed, discontinue use. DO NOT use a door with faulty obstruction sensing.

ELECTROCUTION! • Place opener in protected area so that it does not get wet.• DO NOT spray with water .• DO NOT open the protective covers.• DO NOT operate opener if cable is damaged.

DO NOT DO IT YOURSELF

• Keep the garage door balanced. Sticking or binding doors must be repaired. Garage doors, door springs, brackets and their hardware are under extreme tension and can cause serious personal injury. DO NOT attempt any garage door adjustment. DO NOT use if repair or adjustment is needed. Call for a professional garage door service.

CAUTION: Emergency access • If your garage has no pedestrian entrance door, an emergency access device should

be installed. This accessory allows manual operation of the garage door from outside in case of power failure.

Entrapment under operating door

• Watch the moving door and keep people away until the door is completely opened or closed. DO NOT operate door when persons are near the door.

• DO NOT allow children to play with door controls or transmitters.• Regularly conduct Open and Close cycle testing.• Ensure the garage door is in good working order by undertaking regular servicing.• Wall transmitters should be installed in a location where the garage door is visible, but

out of the reach of children at a height of at least 1.5m.• Install Safety Beams (recommended).

Fall from Ladder • Ensure ladder is the correct type for the job.• Ensure ladder is on flat ground.• Ensure user has 3 points of contact while on ladder.

Entanglement in or laceration from moving door

• Keep hands and loose clothing clear of door and guides at all times.• Keep hands clear of moving door as sharp edges can cause cuts or lacerations.

DIY

15. Home Owner Safety Warnings!


16. Opener Safety & SecurityYour Door CAN NOT be used by the opener when:a. There is a locking device installed.b. There is a power failure.

Your Door CAN be used when:a. There is an emergency, by disengaging the opener.b. There is a power failure, by disengaging the opener. To Disengage the Opener:a. It is recommended to do so with the door in the closed

position.b. Pull down on the manual release cord, until you hear a click.c. Move the door manually.

To Re-Engage the Opener:a. Check the door has not been locked by a locking device.b. Pull down on the manual release cord, until you hear a click.c. The door will now operate from the opener.

CAUTION: When the opener is manually disengaged, the door is no longer locked. To lock the door manually, re-engage the opener after the door is closed.

WARNING! Please test the manual release mechanism to ensure that the manual release is easy to operate. No more than 20kg of force should be required to disengage the door using the manual release cord. If excessive force is required reset the close limit position (Section 10. Resetting Door Limits).

17. Operating your OpenerTo Operate the opener: a. Press the programmed transmitter button until your

door begins to move (usually 2 seconds). Make sure you can see the door when you use the transmitter.

b. If you are in a vehicle you should aim the transmitter through your windscreen as shown.

c. Check that the door is fully open or closed before you drive in or away.

d. If you press the transmitter whilst the door is moving the door will stop. The next press of the transmitter will move the door in the opposite direction.

1. TO DISENGAGE:PULL HANDLE DOWN & RELEASE

2. TO RE-ENGAGE:REPEAT ACTION

PULL HANDLE

WARNING! When operating the manual release (while the door is open) the door may fall rapidly due to weak or broken springs, or due to being improperly balanced. Do not disengage the opener to manual operation with children/persons or any objects including motor vehicles within the doorway.


19. Door Status Indicators Door Status Indicators OPEN LED (green) CLOSE LED (red) Beeper

Open On

Close On

Opening Flashing

Closing Flashing

Door travel stopped Flashing Flashing

Door obstructed when opening Flashing Beeps while door is moving

Door obstructed when closing Flashing Beeps while door is moving

Opener overloaded Alternating flashes Alternating flashes

Mains power interrupted Rapid flashes

Button (Fig 5.1) Function

1. OPERATE Opens/stops/closes the door.

2. CODE SET LED (Red) Flashes when a code is being stored or when the transmitter button is pressed

3. CLOSE LIMIT LED (Red) Illuminates and flashes as the door closes, and remains on when the close limit position has been reached.

4. OPEN LIMIT LED (Green)

Illuminates and flashes as the door opens and remains on when the open limit position has been reached.

5. SERVICE LED (Yellow) Indicates when the opener requires service or repairs.

6. CODE SET and MINUS (-)

Is used for storing or erasing transmitter buttons for door operation

18. User Operating Controls

02 03

04

01

06

05


20. SpecificationsTechnical Specifications Controll-A-Door®

Power DriveRoll-A-Pro®

Power supply 230V - 240Va.c. 50Hz 230V - 240Va.c. 50Hz

Maximum door opening Door Height:

Maximum Door Weight:Door Area:

Door must be well balanced and able to be operated by hand, as per warranty conditions and standard AS/NZS 4505:2012

3.25 turns of the drum wheel (approx. 3000mm)

110kg16.5m2

3.25 turns of the drum wheel (approx. 3000mm)

110kg15.0m2

Minimum sideroom 41mm 41mm

Lift Force 600N (60kg) 500N (50kg)

Nominal force 150N (15kg) 150N (15kg)

Receiver type Multi-frequency UHF FM (433.47, 433.92 & 434.37MHz)

Multi-frequency UHF FM (433.47, 433.92 & 434.37MHz)

Receiver code storage capacity 64 x Tri-Tran+ 4-button Transmitters 8 x Tri-Tran+ 4-button Transmitters

Coding System Tri-Tran+ Technology Tri-Tran+ Technology

Coding type Non-linear encryption algorithm Non-linear encryption algorithm

Number of code combinations Over 100 billion random codes Over 100 billion random codes

Transmitter battery CR2032 (3 Volts) CR2032 (3 Volts)

Courtesy light LED (Light Emitting Diodes) LED (Light Emitting Diodes)

Note: Intermittent operations may occur in areas which experience very strong winds. The strong wind puts extra pressure on the door and tracks which may in turn intermittently trigger the safety obstruction detection system.


Symptom Possible cause Remedy

The opener does not work from the transmitter

The opener does not have power

The battery in the transmitter is flat Transmitter does not contain Tri-Tran+ Technology

The opener has been put into “Vacation Mode” The transmitter button is not programmed to operate the door.

Door Code LED is flashing yet the opener is not working.

Plug a device of similar voltage (e.g. a hairdryer) into the power point and check that it is OK

Replace the battery Check that the transmitter has grey buttons and the model number on the back displays V2. Contact dealer for support if otherwise.

Turn off “Vacation Mode” (Section 14)

Code in the transmitter

Ensure the correct button on the transmitter is being pressed.

One transmitter works but the other/s do not

Faulty transmitter

Flat battery

Replace transmitter Replace battery

The motor is running but the door remains stationary

The opener is disengaged Re-engage the opener

The transmitter range varies or is restricted

Variations are normal depending on conditions e.g. temperature or external interference

The battery life is exhausted

Position of the transmitter in the motor vehicle

Make sure you can see the door when you use the transmitter.

Check the battery status by pressing a button (flashing or no light requires battery to be changed)

Aim the transmitter through the windscreen.

The Courtesy light does not work

LED has failed Change LED.

The door reverses for no apparent reason

This may occur occasionally from environmental conditions such as areas that are windy, dusty or have extreme temperature changes.

If Safety beams are installed they may be partially obstructed.

Ensure the door runs smoothly before increasing the force pressure.

Ensure the beam path is not obstructed. Check the Alignment.

The door stops or moves very slowly.

Garage door in poor condition e.g. springs may be broken.

(Optional Battery Back Up Accessory) The batteries may have little OR no charge

Check the door’s operation.

Connect mains power and leave the batteries to charge. The batteries may take 24 to 48 hours to reach their maximum charge capacity.

21. Troubleshooting


Symptom Possible cause Remedy

The SERVICE LED has started to flash and is beeping numerous times

A Fault has been detected. The fault will be active each time an attempt is made to operate the door.

Record opener function (How many beeps?) then press the LIMIT SET button once to reset the opener. If the fault continues to be tripped contact 1300 300 625 for support.

The Open (Green) LED and Close (Red) LED are flashing alternatively

Opener is overloaded Check the doors operation by disengaging the motor and ensuring the door runs smoothly. If necessary make door adjustments or discontinue use and contact 1300 300 625 for support.

The Open (Green) LED continues to flash

Door obstructed when opening Clear away any obstructions and test door opens correctly. (If door is damaged, contact your door professionl).

The Close (Red) LED continues to flash

Door obstructed when closing

Limits may be cleared

Clear away any obstructions and test door closes correctly. (If door is damaged, contact your door professional).

Remove all power sources (including the battery backup). Wait till all lights are out (10-15 secs), then reconnect power. If Red LED is flashing, limits are not set. Reset Limits.

21 Troubleshooting

If You Need a Service CallIf the opener needs a service please call the dealer who installed the garage door opener (their contact details are usually on a sticker on the back of your garage door). For product assistance contact 13 62 63 within Australia.

BEFORE CALLING you should have the following information to assist in providing the appropriate service:

1. Has anything happened since the opener last operated OK, e.g. a storm, a jolt to the door etc.?2. What is the current light status on the opener? 3. Manually disengage the door (Section 16).

How easy is it to manually open and close the door?4. What model is the opener? (Model no. information is located at the rear of the opener)5. Who installed the opener? (Dealer details should be on a sticker on the back of your garage door)6. When was it installed? (If known)

Date Time Number of Beeps


22. MaintenanceDoor MaintenanceA poorly maintained door could cause fatal / serious injuries or damage to property.

• Frequently examine the door, particularly the cables, springs and mountings for signs of wear, damage or imbalance. DO NOT USE if repair or adjustment is needed since a fault in the installation or an incorrectly balanced door may cause injury.

• Fasterners: Check all screws, nuts and bolts to ensure they are secure.

• Spring Tension: It is natural for springs to lose tension. Should the door become hard to operate or completely inoperative, contact a door professional.

• Guide Tracks: Clean the internal sections of the guide tracks every 3 - 6 months with a cloth dampened with mineral turps or methylated spirits.

DO NOT DO IT YOURSELF:

WARNING! Failure to maintain your garage door may void the warranty on your garage door opener.

DIY Door adjustments should only be carried out by experienced persons, as this function can be dangerous if not performed under strict safety procedures.

When batteries reach the end of their usual life in accordance with Australian Battery Recycling Initiative please follow the next simple steps for protecting the environment. Refer to the B&D website for information on where to recycle batteries in Australia.

DO NOT throw the batteries in municipal waste. This symbol of the crossed out wheeled bin indicates that the battery should not be placed in the municipal waste. Check your local regulations for appropriate disposal of the batteries.

Recycling all batteries will have other environmental and social

WARNING! Prior to disposal, recycling, or collection, all battery terminals must be securely insulated with a non conductive material to prevent any two batteries from short circuiting and generating heat during storage or transport. Battery terminals may be insulated with electrical tape; or batteries may be individually packaged in a non conductive material (e.g., plastic bag or original packaging).

24. Battery Disposal

Battery Type: 3V Lithium Battery CR2032. • To test the battery is working, press and hold a transmitter button.

Check Light Status table to determine if battery needs replacing

Light Status Battery StatusSolid OKFlashing Requires

replacementNo light Requires

replacement

23. Battery Replacement

Use a pen to push the battery down through the side opening to release battery

Run the Safety Testing procedures MONTHLY in Section 11 to ensure garage door is fit for use.

tip

• Use finger nails to separate the transmitter casing to expose circuit board.

• Use a non-metallic object (e.g. pen) to remove the battery.

benefits: • Some batteries are less toxic but hazardous for other reasons. Lithium batteries can explode or catch fire in landfill, while button cells are dangerous if swallowed by children. Recycling offers a safe and environmentally responsible solution for end of life batteries.

• Battery recycling recovers non-renewable materials such as lead, cadmium, stella, zinc, manganese,

cobalt, silver, plastics and rare earth elements. • Removal of batteries and other hazardous household products from household waste facilitates the recovery of organic materials through alternative waste technologies such as composting. Batteries and heavy metals are known contaminants in compost.

• The community supports recycling because it reduces waste to landfill and achieves environmental benefits.


25. Service Schedule

B&D Doors is a division of B&D Australia Pty Ltd Phone: 13 62 63 Website: www.bnd.com.au

Year / Approx. Cycles

Date Details

1 / 3,000

2 / 6,000

3 / 9,000

4 / 12,000

5 / 15,000


26. WarrantyThis Warranty is given by B&D Doors a division of B&D Australia Pty Ltd (ABN 25 010 473 971), 34-36 Marigold St, Revesby 2212, 13 62 63, [email protected].

PLEASE NOTE:• This Warranty is in addition to any statutory, non-excludable guarantees or warranty rights and remedies under the law. See section 5 below.• This warranty applies to the original purchaser only and may not be transferred.• This Warranty is to be read in conjunction with the owner’s copy of the installation instruction manual.• In this warranty, ‘B&D Representative’ means an entity authorized by B&D to service B&D products. Please check the B&D website for details.

NOTE: CONSUMABLES (eg Batteries in remote control transmitters and light bulbs and fuses) are not covered by this warranty

1. MAKING A CLAIMa) The product parts in the above table should operate in accordance with the

product manual for the time period shown, provided you comply with the manufacturer’s instructions concerning installation, operation, maintenance and testing. Failure to do so may void all or part of this warranty.

b) If, during the relevant warranty period, a product part in the table above appears to contain a defect, call the retailer from whom you purchased the product, or B&D on 13 62 63, and they will instruct you what to do next.

c) You are responsible for the cost of making a claim under this Warranty. Additional access expenses where the Product is not readily accessible must be borne by you.

d) If B&D or B&D’s Representative confirms the product is defective and covered by this Warranty, B&D will repair or replace it (at B&D’s sole option) at no cost to you. Goods presented for repair may be replaced or repaired by refurbished goods or parts of the same type.

2. WARRANTY CONDITIONSIt is a condition of this warranty that:a) you provide a copy of the receipt of original purchase of the product, and

the serial number of the Product which can be found on the label adhered to the Product.

b) the door and opener are properly maintained by being serviced by a qualified professional at regular, appropriate intervals. What is appropriate may vary based on environmental factors (eg. weather, salt exposure) and level of usage. Based on average use and environmental conditions, B&D recommends that the product is serviced by B&D or a B&D Representative, within 12 months of installation (to allow for new doors to settle) and at regular intervals not exceeding 2 years.

It is a condition of the below warranties that the manual operating (opening and closing) force of the door by hand does not exceed 20kg.

MODEL WARRANTY DOOR (MAX)

SECTIONAL

CAD Advance 7 yrs / 20,000 cycles 200kg

CAD S 7 yrs / 20,000 cycles 175kg

Panel Pro 5 yrs / 10,000 cycles 110kg

ROLLING

CAD PowerDrive 7 yrs / 20,000 cycles 110kg

Roll-A-Pro 5 yrs / 10,000 cycles 110kg

EXTRAS

TRACK ASSEMBLY(includes all parts)

1 year

TRANSMITTERS & ACCESSORIES

1 year

3. WARRANTY EXCLUSIONSThis warranty excludes defects or improper operation resulting from:a) excessive wear and tear that may cause the product to fail;b) accidental, deliberate or negligent damage or damage cause by insects,

dirt, plants or other objects;c) blown fuses, electrical surges, power surges or power spikes or faulty or

unsuitable electrical wiring of structures to which the product is affixed;d) theft, fire, flood, rain, water, lightning, storms or any other acts of God;e) salt or other corrosion due to environmental conditions,f) any installation, configuration or use of the product contrary to the instructions

supplied with the product;g) maximum continuous operating time exceeding 1 minute in10 minutes;h) the manual operating (opening and closing) force of the door by hand

exceeding 20kg;i) weight exceeding amounts listed in table above;j) the door used with the product not being in safe working order and condition;k) any modification to the product or acts of any person in respect of the

product which are not authorized by B&D and which impact Product performance;

l) installation of a residential garage door opener in a commercial or industrial premises or in a dwelling other than a single-family dwelling; or

m) radio or electrical interference or lack of availability of signal.

4. OTHER CONDITIONSa) This Warranty is not transferable.b) The warranty period stated in the table will not be extended for Products or

parts repaired or replaced during the relevant warranty period.c) Where the Product is sold by any person other than B&D, except for the

warranty set out above, such person has no authority from B&D to give any warranty or guarantee on B&D’s behalf in addition to the warranty set out above.

5. STATUTORY GUARANTEES OR WARRANTIES IN AUSTRALIAIf you are a consumer under the Australian Consumer Law, our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.This warranty certificate and other statements contained in this document or other B&D documents given to you do not exclude, restrict or modify the application of all or any of the provisions of the Australian Consumer Law.

To the extent permitted by the Act or other laws, B&D:a) limits its liability for breach of a statuatory guarantee to the payment of the

cost of replacing the Product or acquiring an equivalent Product; andb) expressly excludes any liability for consequential loss and incidental or

indirect damages (including but not limited to damages for loss of business profits, income, business, goodwill or reputation, or business interruption) due to a defect of the Product.


27. Optional AccessoriesThere are a range of additional accessories for your added convenience and security. Contact your Dealer for installation of these accessory items.

• Safety Beams - Provides additional protection if the door is closing onto your property or person. Simply breaking the beam “stops” the door!

• Keyring Transmitter - Ideal for personal use when entry into the house may be via the garage.

• Wall Button Transmitter - Allows you to operate the opener within 10 metres of the door. Ideal for mounting inside the house.

• Wireless Keypad - The entry keypad allows entry to the garage without using a transmitter.

• Battery Back-up - The opener has a provision for a Battery Back Up kit that allows continued operation of the door in the absence of mains power.

(Not available with the Roll-A-ProTM)

• External Antenna - For sites where radio range may be reduced.

IMPO

RTA

NT

NO

TE:

On

ly Tr

i-Tra

n+TM

Tec

hn

olo

gy

Tra

nsm

itte

rs a

nd

Key

pa

ds

are

co

mp

atib

le w

ith th

ese

p

rod

uc

ts.

TB-6 Shown


B&D Doors is a division of B&D Australia Pty Ltd ABN 25 010 473 971

Is your door sticking and hard to operate?

It may be time for a service (for more details see section 22)

For a service, contact your dealer using the details below...

Dealer:

© copyright 2018

Documents

Instruction Manual Controll-A-Door Power Drive · Controll-A-Door® ®Power Drive & Roll-A-Pro Instruction Manual 3 1. Installation Safety Warnings! WARNING! •he door may operate