Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
CONTENTS
SAFETY INFORMATION
SPECIFICATIONS
OVERVIEWSupplied Items
Product Features
SETUPCharge
Load PaperExternal Memory
OPERATIONPower ON/OFFTaking A Photo
ViewfinderAspect Ratio
Printing and ReprintLED Indicator
Troubelshooting
P3
P13
P4
P5-8
P9-12
SAFETY INFORMATION
3
READ BEFORE USE
Please read the following instructions and safety precautions before using the device.For regulatory and additional safety information, refer to the Regulation and Warranty Information sheet included in your package contents.RMN: PP3001Regulatory Model Identification Number is assigned for regulatory identification purpose.
• Keep away from children and infants. Improper use of this product may cause suffocation or accident.• Stop using the device immediately if it emits smoke or a strange smell, or otherwise behaves abnormally. • Do not look at the sun or bright lights through the viewfinder or the lens. Blindness or vision problems could result. • Do not fire the flash near the eyes. It may hurt the eyes.• A strap wound around a child’s neck may result in asphyxiation. If your product uses a power cord, mistakenly winding the cord around a child’s neck may result in asphyxiation.• Turn the device off in places where camera use is prohibited. The electromagnetic waves emitted by the camera may interfere with the operation of electronic instruments and other devices. Exercise adequate caution when using the product in places where use of electronic devices is restricted, such as inside airplanes and medical facilities.
• When operating in extreme weather, the device might not print. Let the printer temperature adjust to the recommended operating temperature of 15º to 32ºC, before attempting to print again.• When charging, please charge the device at the recommended temperature of 15º to 32ºC.• Use a soft dry cloth to clean the device. Do not clean with a damp cloth or volatile liquids such as paint thinner. • Keep the top cover closed to avoid dust and other particles from entering the inside of the device.• If the device is not functioning properly, please contact the dealer you purchased this product from or Canon Service & Support at https://asia.canon/en/consumer/buy.• Never expose the battery to high temperatures, direct heat, or dispose by incineration.• Electromagnetic interference or electrostatic discharge may cause the device to malfunction or the memory to be lost or altered. Should this occur, use a pin, or similar item to press the [RESET] button at the bottom of the device.
WARNING
CAUTION
OVERVIEW
4
SUPPLIED ITEMS
PRODUCT FEATURES
Instant Camera Printer Quick Start Guide USB Cable Wrist StrapRegulation andWarranty
Information sheet
Camera Lens
Selfie Mirror
Print Output Slot
Strap Hole
Flash
Status LED
Power Button
Shutter Button
Viewfinder
• Keep away from children and infants. Improper use of this product may cause suffocation or accident.• Stop using the device immediately if it emits smoke or a strange smell, or otherwise behaves abnormally. • Do not look at the sun or bright lights through the viewfinder or the lens. Blindness or vision problems could result. • Do not fire the flash near the eyes. It may hurt the eyes.• A strap wound around a child’s neck may result in asphyxiation. If your product uses a power cord, mistakenly winding the cord around a child’s neck may result in asphyxiation.• Turn the device off in places where camera use is prohibited. The electromagnetic waves emitted by the camera may interfere with the operation of electronic instruments and other devices. Exercise adequate caution when using the product in places where use of electronic devices is restricted, such as inside airplanes and medical facilities.
• When operating in extreme weather, the device might not print. Let the printer temperature adjust to the recommended operating temperature of 15º to 32ºC, before attempting to print again.• When charging, please charge the device at the recommended temperature of 15º to 32ºC.• Use a soft dry cloth to clean the device. Do not clean with a damp cloth or volatile liquids such as paint thinner. • Keep the top cover closed to avoid dust and other particles from entering the inside of the device.• If the device is not functioning properly, please contact the dealer you purchased this product from or Canon Service & Support at https://asia.canon/en/consumer/buy.• Never expose the battery to high temperatures, direct heat, or dispose by incineration.• Electromagnetic interference or electrostatic discharge may cause the device to malfunction or the memory to be lost or altered. Should this occur, use a pin, or similar item to press the [RESET] button at the bottom of the device.
1
4567
32
9
10
8
Speaker
Printer Cover
Aspect Ratio Button
Reprint Button
Micro USB Port
Charging Status LED
MicroSD Card Slot (up to 256GB)
Reset Button
121314151617
11
CANON ZINK™Photo Paper(10 sheets)
* To reset the device, press with a pin
1
4
4
5
67
3
29
8
10
13
141516
17
9
11
12
ZINKPaper
SETUP
5
CHARGING
The device has a built-in battery. Please fully charge the device via the USB cable provided before using.
HANDLE THE USB CABLE WITH CARE WHILE CHARGING
• Do not place any heavy objects on top of the cable.• Do not place the USB cable near heat.• Do not scratch, damage, twist or pull hard on the cable.• Do not plug or unplug the cable with wet hands.• Avoid too high/too low temperature or humid conditions.• Please unplug the USB cable from power source after charging.• Please use the supplied USB cable for charging.
About USB Cable
Insert the smaller end of the supplied USB cable into the device and other end into a chargeable USB adapter.
The charging LED light will turn red to indicate charging.
Once fully charged, the charging LED will turn green.− Operating time may vary depending on the battery status, operational status and environment conditions.
1
3
2
NOTE
Charging Status LEDCharging : RedFull : Green
6
LOAD PAPER
Remove the cover by sliding it forward in the direction of the arrow.1
Open a single pouch of photo paper (10 sheets + blue SMART SHEET™).
3
2
Place all 10 photo paper sheets and the one SMART SHEET™ into the photo paper compartment.− Stack the photo paper on top of the blue SMART SHEET™, making sure the blue barcode and the photo paper logos are facing down.
4 Place the top cover back onto the device. It should click into place when closed properly. − The blue SMART SHEET™ will be sent through the device automatically before the first print.
7
EXTERNAL MEMORY
An external MicroSD card (up to 256 GB) is needed for saving captured photos. Only FAT16, FAT32 and exFAT format are supported.
Use the following memory cards (sold separately)• MicroSD memory cards *1• MicroSDHC memory cards *1 *2• MicroSDXC memory cards *1 *2*1 Cards conforming to SD standards. However, not all memory cards have been verified to work with the camera.*2 UHS-I memory cards are also supported.
PREPARING A MEMORY CARD
• Insert the MicroSD card into the slot at the bottom of the device. You will feel a slight click when the card is fully inserted .• Push on the top of the card to release it. Gently pull to fully remove the card from the device.• If there is an error on reading /writting to the MicroSD card, remove the MicroSD card and restart the device.• Connect the device to a computer by USB cable. Double-click the external drive image when it appears on the computer to view and save the photos.
INSTALL AND REMOVE THE MicroSD CARD
8
• Only load 10 ZINK™ photo paper sheets and 1 SMART SHEET™. Do not load more as it can result in paper jams or printing errors. • If there is a paper jam, simply turn the printer OFF and ON to automatically clear the paper jam. Don’t try to pull the paper out.• While the device is printing, don’t pull or tug on the photo paper.• Handle photo paper carefully to avoid damage or bending.• Keep the photo paper clean when loading. If photo paper is dirty or damaged, it may result in a paper jam or print error.• Don’t open a new pouch of photo paper until you are ready to load it into your device. • Don’t expose photo paper to direct sunlight or moisture.
• Don’t leave your photo paper in an area where the temperature or humidity is out of the suggested conditions indicated on the pouch. It may reduce the quality of the printed photo.
WHEN USING PHOTO PAPER
• Each pouch of photo paper contains 10 sheets of photo paper and 1 blue SMART SHEET™.• Load the SMART SHEET™ and photo paper from within the same pouch for optimal print quality. Each SMART SHEET™ is specifically tuned for the pouch of paper it is contained in.• The SMART SHEET™ will be sent through the device automatically before the first print to clean the printer and optimize print quality for that specific paper pouch (10 sheets). • Keep the SMART SHEET™ and only discard after you have printed all 10 sheets of photo paper in the pouch. If print quality is not as expected, you can reuse the SMART SHEET™ if the paper is still from the same pouch. Simply slide the SMART SHEET™ with its barcode-side down underneath the remaining photo paper.• Using a SMART SHEET™ from another pouch may result in reduced print quality.
ABOUT THE SMART SHEET™
• Use and keep the device in the recommended environment of 15º to 32º C and 40-55% relative humidity.
MAINTAINING THE DEVICE
NOTE
9
OPERATION
POWER ON/OFF
VIEWFINDER
TAKING A PHOTO
Compose an image with the frame mark in the viewfinder.
When the LED indicator turns to a steady white , the device is ready to Use.
2
• When the device is idle for about 5 minutes, it will automatically power off. User can resume the device by pressing the Power button again.
AUTO POWER OFF
50cm- ∞
1 Press and hold the Power button until the LED indicator light turns on.
1 Hold the device, confirm the desired composition of the image.
3 Press and hold the Power button to turn off the device.
Press the Shutter buttonto take a photo.
The camera will automatically trigger the flash if it is necessary for the light-ing conditions.
Use the reflective plate besides the lens as a self-portrait mirror for selfie.
2
50cm - ∞
2 x 3
2 X 3 Frame Markfor normal shooting
at 1m - ∞
2 x 2
2 X 2 Frame Markfor normal shooting
at 1m - ∞
10
• The photo will be printed out immediately after taking the photo.• The device can hold up to 3 images at a time to print.
PRINTING A PHOTO
ASPECT RATIO
PRINTING AND REPRINT
When the aspect ratio is 2x2, the blank area of the photo paper is different. It is based on how the device is held.
When you have captured a photo and it is printed out, if you want to duplicate the same photo or distribute several pieces of the same photos in a party, you just simply press the Reprint button to reprint the last printed photo.
REPRINT A PHOTO
User can choose between two aspect ratios, 2x3 and 2x2 with the Aspect ratio button .Aspect ratio can be changed at any time before taking a photo.
11
LED INDICATOR
SMART SHEET™Error
ProcessingSMART SHEET™
Power Off
No Paper
Paper Jam/Cover Open
Get Ready forPrinting
Printing Photo
MS Mode(Mass Storage Mode)
MicroSD CardError
TemperatureToo High
TemperatureToo Low
Standby
Power On
Status Operation LED Indicator
When the device detects wrong SMART SHEET™ is inserted, or other SMART SHEET™ error
After the device is powered on
Press and hold Power button
White
Off
Magenta
Red (Until temperaturereturns to normal)
Cyan (Until temperaturereturns to normal)
Yellow > Magenta > Cyan > White(Looping)
Press and hold Power button
When the device is printing outSMART SHEET™
When the device has no paper,the device will not allow for taking a photo
When there is a paper jam orthe printer cover is opened
Preparing for printing
When the device is printing a photo
Device is connected to a computer
When device temperature is too hot
Cannot write data into MicroSD Card
When device temperature is too cold
Red
Red
White
Blue
White
Magenta
WhiteWhite
12
Low Battery
Very Low Battery
When battery level down to 20%
When battery level is very lowRed > White (Looping)
White > Red (Looping)
Red
N/A
N/A
Red
Red
Red
Magenta
TROUBLESHOOTING
MicroSD CardError
Paper FeedingFailed
Paper Jam
No Paper
Red
Printer Coveris not closedproperly
Overheat
Device doesnot Work
Take a Photo
Status LED Indication Actions
• Check if the MicroSD card is inserted properly• Check if the MicroSD card is full• Check if the MicroSD card is corrupted• Check if the MicroSD card is compatible
• Wait until the device temperature returns to normal, the device will resume working again
• Make sure print queue buffer is available• Make sure device has Canon ZINK™ photo paper
• Make sure the battery level is not too low. If it is, recharge the device
• Close the printer cover properly
• Reload Canon ZINK™ photo paper into the device
• Open the paper compartment cover to check if Canon ZINK™ photo paper is inserted
• Power off and on the device, the photo paper will be fed out automatically
Printer Head Cooling
Checking the printer headtemperature and letting it cooldown before printing Cyan
Status Operation LED Indicator
13
SPECIFICATIONS
Subject to change without notice
Printing Technology ZINK™
Printing Resolution 314 x 500 dpi (dots per inch)
Printing Speed Approximately 50 seconds - Motor starts and stops, at room temperature 25º C
Photo Aspect Ratio 2" x 2" or 2" x 3"
Compatible Paper Canon ZINK™ Photo Paper : ZP-2030-20 (20 sheets) / ZP-2030-50 (50 sheets) / 2" x 3" / Peel-and-Stick Back
Paper Capacity Up to 10 sheets of ZINK™ photo paper + 1 SMART SHEET™
Photo Resolution 5MP
Focal Length 24mm
Aperture f 2.4
Focusing Range 50cm - ∞Sensitivity Auto (ISO 100 - 1600)
Flash YES (Auto)
Flash Range 0.5m - 1.0m
Memory Card MicroSD Card, up to 256GB
Power Source Built-in Rechargeable Li-Polymer Battery 700mAh, 7.4V
Charging Speed Approximately 90 minutes (Full Charge)
Power Adapter Output Current : 1.6A (min) Voltage : 5V
Environmental Parameters - Recommended Printing Operating, Charging, and Storage Temperature : 15º to 32º C - Recommended Printing Operating, Charging, and Storage Humidity : 40-55% RH - Operating Temperature : 5º to 40º C - Operating Humidity : < 70% RH
Automatic Power-off 5 minutes
Dimension 121mm (W) x 78.3mm (H) x 23.7mm (D)
Weight 170g
Compatible OS Windows 7 / 8 / 8.1 / 10 (for Computer) Mac OSX 10.10 - 10.14
Connection for Charging USB 2.0 (Micro USB)and Data Transfer