Installation Notes MC-CAT Version 6.0

Confidential / Property of Danfoss Bauer GmbH

23 June 2006 1Danfoss Bauer GmbH

Installation Notes MC-CAT Version 6.0Installation Notes MC-CAT Version 6.0



Contents

Installation Notes MC-Cat Version 6.0

Installation MC-Cat Version 6.0

Installation CAD Software2

1

Update of CAD Software

3 Update of MC-Cat Version 6.0

4

Download MC-Cat Version 6.0 in Internet5



MC-CAT

Wenn the CD is put in the drive and AUTOPLAY is activated, the above screen appears.If not, then please start SETUP.EXE on the CD-ROM.Select the language for the installation and press OK.

zurückzurück




MC-CAT

The CD-ROM can be started here „Start from CD…“, (without installation) the CAD Software installed „Install CAD Software“ or the CD Software installed with „WEITER >“

zurückzurück




MC-CAT

The target directory can be selected here, the installation goes further with WEITER >.

zurückzurück




MC-CAT

The name for the Start Menu can be given here, then further with WEITER >.

zurückzurück




MC-CAT

Is a start symbol required for the desktop?Then click here and then WEITER >

zurückzurück




MC-CAT

Click INSTALLIEREN to complete the installation.

zurückzurück




Contents




1



4




CAD Software

Click on „Install CAD-Software…“.CAUTION!Installations- or Administrator Rights are needed.

zurückzurück




CAD Software

Do you want to install?Click on OK . A click on Abbrechen will terminate the installation.

zurückzurück




CAD Software

Information over the further installation…No input is necessary.

zurückzurück




CAD Software

Please read the notes carefully and then click on WEITER>.

zurückzurück




CAD Software

Select here the components to install. Danfoss and WorldCAT-CIF must be installed. The other componets are tools to measure the geometries generated in case no CAD system is available. Then click WEITER>.

zurückzurück




CAD Software

The installation of the single components now begins. Please read the notes carefully. Click WEITER> to carry on with the installation.

zurückzurück




CAD Software

Select here the 2D CAD system to which the WORLDCAT-CIF will connect to on the same computer. If no system is available leave all selections open. The click on WEITER>.

zurückzurück




CAD Software

The installation of WORLDCAT-CIF now takes place.Click on WEITER>.

zurückzurück




CAD Software

Select here the 3D CAD system to which the WORLDCAT-CIF will connect to on the same computer. If no system is available leave all selections open. The click on WEITER>.

zurückzurück




CAD Software

The installation of WORLDCAT-CIF 3D now takes place.Click on WEITER>.

zurückzurück




CAD Software

Click on Fertigstellen> to complete the installation of the WorldCAT-CIF.

zurückzurück




CAD Software

Now all CAD Information will be installed.Click on WEITER>.

zurückzurück




CAD Software

The Installation is now ready. Continue by clicking on WEITER>.

zurückzurück




CAD Software

All components are now installed.Click on WEITER> to complete the installation.

zurückzurück




CAD Software

Please read the notes carefully and finally click on OK to re-start the computer.

zurückzurück




Contents




1



4




Update MC-Cat Version 6.0 in Internet

Click on the Symbol to reach the update page. Should one of the lines be RED , the MC-Cat update button will be active. Click here to start the UPDATES …

zurückzurück





Max. 3 updates will be started. Should only 1 be started, then the file must be downloaded, MC-Cat closed down, the update started and MC-Cat started again. Then further downloads can be started.

zurückzurück





Select the installation language and click OK.

zurückzurück





Read carefully and click WEITER>.

zurückzurück





The EXACT directory of the MC-Cat should be shown here. Please check carefully. Further with click on WEITER>.

zurückzurück





Click Ja.

zurückzurück





Which Start Menu name should be used??Then click WEITER>.

zurückzurück





Should another desktop symbol be created? (Not necessary)The click on WEITER>.

zurückzurück





The selection can be seen here. Should the details be incorrect then click on <ZURÜCK otherwise Installieren.

zurückzurück





The installation progress is shown……

zurückzurück





The installation is now finished. Click on Fertigstellen to complete the installation. MC-Cat is then re-started. If necessary, further updates can now ne started.

zurückzurück




Contents




1



4




CAD Software UPDATE

After downloading the UPDATE, and click on the EXE file, the given message appears. Click OK to continue.

zurückzurück




CAD Software UPDATE

Should no user inouts be required, the given screen appears after a short time. Click on OK.

zurückzurück




CAD Software UPDATE

Should user input be required, the following screen appears after clicking OK on the previous screen. Read carefully and click WEITER> .

zurückzurück




CAD Software UPDATE

In this example the CAD system (if present) needs to be selected. Should no system be present, all points should be de-selected and then click on WEITER>.

zurückzurück




CAD Software UPDATE

Click on Fertigstellen> to complete the installation.

zurückzurück




Contents




1



4




Download MC-Cat Version 6.0 in Internet

www.bauergear.info

zurückzurück

Click hier to reach the downloads.





Firstly 1) MC-Cat and then 2) CAD Files should be downloaded. The CAD Files can be downloaded as 1 file or smaller 10MB files….

zurückzurück

Click here for MC-Cat….

Click here for CAD Files(1 File)….

Click here for CAD Files(7 Files)….





The download will be started. The ZIP archive should be saved and extracted in a temporary directory and the file SETUP.EXE started.

zurückzurück




Contents




1



4


Documents

Installation Notes MC-CAT Version 6.0