Installation Manual SINUMERIK Integrate MMT, MMP, AMB, … · MMT, MMP, AMB, AMC, AMM, AMP Installation Manual, 03/2013, 6FC5397-6EP40-0BA0 3 Preface SINUMERIK documentation The SINUMERIK

SINUMERIK

SINUMERIK Integrate MMT, MMP, AMB, AMC, AMM, AMP

Installation Manual

Valid for: control systems SINUMERIK 840D sl/ 840DE sl/ 840Di sl/ 840DiE sl SINUMERIK 840D/840Di/810D software SINUMERIK Integrate

03/2013 6FC5397-6EP40-0BA0

Preface

Introduction 1

Installing/uninstalling the local server

2

Client setup Manage MyTools (MMT)

3

Client setup Manage MyPrograms (MMP)

4

Client setup Access MyBackup (AMB), Analyze MyCondition (AMC)

5

Client setup Access MyMachine (AMM)

6

Client setup Analyze MyPerformance (AMP)

7

Annex A A

Siemens AG Industry Sector Postfach 48 48 90026 NÜRNBERG GERMANY

Order number: 6FC5397-6EP40-0BA0 Ⓟ 04/2013 Technical data subject to change

Copyright © Siemens AG 2013. All rights reserved

Legal information Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger.

DANGER indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION indicates that minor personal injury can result if proper precautions are not taken.

NOTICE indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage.

Qualified Personnel The product/system described in this documentation may be operated only by personnel qualified for the specific task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified personnel are those who, based on their training and experience, are capable of identifying risks and avoiding potential hazards when working with these products/systems.

Proper use of Siemens products Note the following:

WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems. The permissible ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability We have reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions.

MMT, MMP, AMB, AMC, AMM, AMP Installation Manual, 03/2013, 6FC5397-6EP40-0BA0 3

Preface

SINUMERIK documentation The SINUMERIK documentation is organized in the following categories:

● General documentation

● User documentation

● Manufacturer/service documentation

Additional information You can find information on the following topics at www.siemens.com/motioncontrol/docu:

● Ordering documentation/overview of documentation

● Additional links to download documents

● Using documentation online (find and search in manuals/information)

Please send any questions about the technical documentation (e.g. suggestions for improvement, corrections) to the following address:

[email protected]

My Documentation Manager (MDM) Under the following link you will find information to individually compile OEM-specific machine documentation based on the Siemens content:

www.siemens.com/mdm

Training For information about the range of training courses, refer under:

● www.siemens.com/sitrain

SITRAIN - Siemens training for products, systems and solutions in automation technology

● www.siemens.com/sinutrain

SinuTrain - training software for SINUMERIK

FAQs You can find Frequently Asked Questions in the Service&Support pages under Product Support. http://support.automation.siemens.com

Preface

MMT, MMP, AMB, AMC, AMM, AMP 4 Installation Manual, 03/2013, 6FC5397-6EP40-0BA0

SINUMERIK You can find information on SINUMERIK under the following link:

www.siemens.com/sinumerik

Target group This document addresses commissioning engineers and machine tool manufacturers. The document provides detailed information that commissioning engineers require to commission the SINUMERIK Integrate software.

Prerequisite (area of validity) This manual is valid for use with the following product versions:

Manage MyTools (MMT) Version 2.5

Manage MyPrograms (MMP) Version 2.5

Analyze MyCondition (AMC) Version 4.12

Access MyBackup (AMB) Version 4.12

Access MyMachine (AMM/E) Version 2.0

Analyze MyPerformance (AMP) Version 2.5

Benefits The installation manual instructs the target group on how to install and uninstall the software correctly.

Standard scope This documentation only describes the functionality of the standard version. Additions or revisions made by the machine manufacturer are documented by the machine manufacturer.

Other functions not described in this documentation might be executable in the control. This does not, however, represent an obligation to supply such functions with a new control or when servicing.

For the sake of simplicity, this documentation does not contain all detailed information about all types of the product and cannot cover every conceivable case of installation, operation, or maintenance.

Technical Support You will find telephone numbers for other countries for technical support in the Internet under http://www.siemens.com/automation/service&support

Preface


EC Declaration of Conformity The EC Declaration of Conformity for the EMC Directive can be found on the Internet at:

http://support.automation.siemens.com

Here, enter the number 15257461 as the search term or contact your local Siemens office.

Preface



Table of contents

Preface ...................................................................................................................................................... 3

1 Introduction.............................................................................................................................................. 11

1.1 Product overview .........................................................................................................................11

1.2 Application areas and interaction.................................................................................................13

1.3 System preconditions...................................................................................................................18

2 Installing/uninstalling the local server....................................................................................................... 21

2.1 Introduction ..................................................................................................................................21

2.2 Installing Windows services .........................................................................................................22 2.2.1 Under Windows Server 2003 32 bit .............................................................................................22 2.2.2 Under Windows Server 2008R2 ..................................................................................................29 2.2.3 Under Windows 7.........................................................................................................................41

2.3 MMT server ..................................................................................................................................45 2.3.1 Installing the server setup MMT...................................................................................................45 2.3.2 Uninstalling the server setup MMT ..............................................................................................53

2.4 MMP server..................................................................................................................................54 2.4.1 Installing the server setup MMP...................................................................................................54 2.4.2 Uninstalling the server setup MMP ..............................................................................................60

2.5 AMP, AMC, AMB server ..............................................................................................................61

3 Client setup Manage MyTools (MMT) ...................................................................................................... 69

3.1 Overview ......................................................................................................................................69

3.2 SINUMERIK Operate machine ....................................................................................................69 3.2.1 Display the "SINUMERIK Integrate" softkey................................................................................70 3.2.2 Enabling SINUMERIK Integrate applications...............................................................................70 3.2.3 Inhibiting SINUMERIK Integrate applications ..............................................................................72 3.2.4 Installing the basis installation and MMT.....................................................................................73 3.2.4.1 Basis installation, installing Installer ............................................................................................73 3.2.4.2 Basis installation, installing Base Setup ......................................................................................75 3.2.4.3 Installing the MMT application .....................................................................................................78 3.2.5 Uninstalling the basis installation and MMT.................................................................................80 3.2.5.1 Uninstalling the MMT application.................................................................................................80 3.2.5.2 Basis installation, uninstalling Base Setup ..................................................................................82 3.2.5.3 Basis installation, uninstalling Installer ........................................................................................83

3.3 HMI-Advanced machine...............................................................................................................84 3.3.1 Installing MMT SINUMERIK.........................................................................................................84 3.3.2 Uninstalling MMT SINUMERIK ....................................................................................................90

3.4 Workstation PC ............................................................................................................................91 3.4.1 Installing MMT on a PC................................................................................................................91 3.4.2 Uninstalling MMT on a PC ...........................................................................................................96

Table of contents


4 Client setup Manage MyPrograms (MMP) ............................................................................................... 97

4.1 Overview ..................................................................................................................................... 97

4.2 SINUMERIK Operate machines.................................................................................................. 97 4.2.1 Display the "SINUMERIK Integrate" softkey ............................................................................... 98 4.2.2 Enabling SINUMERIK Integrate applications.............................................................................. 98 4.2.3 Inhibiting SINUMERIK Integrate applications ........................................................................... 100 4.2.4 Installing the basis installation and MMP.................................................................................. 101 4.2.4.1 Basis installation, installing Installer.......................................................................................... 101 4.2.4.2 Basis installation, installing Base Setup.................................................................................... 103 4.2.4.3 Installing the MMP application .................................................................................................. 106 4.2.5 Uninstalling the basis installation and MMP.............................................................................. 108 4.2.5.1 Uninstalling the MMP application.............................................................................................. 108 4.2.5.2 Basis installation, uninstalling Base Setup................................................................................ 110 4.2.5.3 Basis installation, uninstalling Installer...................................................................................... 111

4.3 HMI-Advanced machine............................................................................................................ 112 4.3.1 Installing MMP SINUMERIK...................................................................................................... 112 4.3.2 Uninstalling MMP SINUMERIK ................................................................................................. 117

4.4 Workstation PC ......................................................................................................................... 118 4.4.1 Installing MMP on a PC............................................................................................................. 118 4.4.2 Uninstalling MMP on a PC ........................................................................................................ 122

5 Client setup Access MyBackup (AMB), Analyze MyCondition (AMC) .................................................... 123

5.1 Overview ................................................................................................................................... 123

5.2 SINUMERIK Operate machine.................................................................................................. 123 5.2.1 Display the "SINUMERIK Integrate" softkey ............................................................................. 123 5.2.2 Enabling SINUMERIK Integrate applications............................................................................ 124 5.2.3 Inhibiting SINUMERIK Integrate applications ........................................................................... 126 5.2.4 Installing the basis installation................................................................................................... 127 5.2.4.1 Basis installation, installing Installer.......................................................................................... 127 5.2.4.2 Basis installation, installing Base Setup.................................................................................... 129 5.2.5 Uninstalling the basis installation .............................................................................................. 132 5.2.5.1 Basis installation, uninstalling Base Setup................................................................................ 132 5.2.5.2 Basis installation, uninstalling Installer...................................................................................... 133

5.3 HMI-Advanced machine............................................................................................................ 134 5.3.1 Installing SINUMERIK Integrate client ...................................................................................... 134 5.3.2 Configuring user-specific parameters - expert mode................................................................ 149 5.3.2.1 Overview of the expert mode .................................................................................................... 149 5.3.2.2 Changing the URLs of the client ............................................................................................... 150 5.3.2.3 Configuring Internet access ...................................................................................................... 153 5.3.2.4 Selecting a driver ...................................................................................................................... 155 5.3.2.5 Changing data volumes and protocol settings.......................................................................... 156 5.3.2.6 Changing the target directory data buffering............................................................................. 158 5.3.2.7 Changing the log file target directory ........................................................................................ 159 5.3.2.8 Changing the download method for the boot script .................................................................. 161 5.3.2.9 Changing the start parameter client.......................................................................................... 162 5.3.2.10 Changing the time synchronization between PLC and HMI ..................................................... 164 5.3.3 Integrating the client setup as external applications ................................................................. 165 5.3.4 Changing, repairing and uninstalling programs ........................................................................ 168

5.4 Machine PC............................................................................................................................... 173

Table of contents


5.4.1 Installing SINUMERIK Integrate client (IPC)..............................................................................173 5.4.2 Changing, repairing and uninstalling programs .........................................................................186

5.5 Workstation PC ..........................................................................................................................190 5.5.1 Client setup ................................................................................................................................190

6 Client setup Access MyMachine (AMM) ................................................................................................ 191

6.1 Overview ....................................................................................................................................191

6.2 SINUMERIK Operate machines.................................................................................................191 6.2.1 Installing AMM Service Mode via Microsoft software installation (MSI package)......................191 6.2.2 Uninstalling AMM Service Mode................................................................................................195

6.3 HMI-Advanced machine.............................................................................................................196 6.3.1 Configuring SINUMERIK Integrate client...................................................................................196 6.3.2 Uninstalling client setup .............................................................................................................209

6.4 Machine PC................................................................................................................................211 6.4.1 Configuring SINUMERIK Integrate Client (IPC).........................................................................211

6.5 Workstation PC ..........................................................................................................................223 6.5.1 Installing client setup Service Engineer ActiveX Client .............................................................223

6.6 Installing updates .......................................................................................................................230 6.6.1 Update V3.0 with WebEx/RANG V01 ........................................................................................230 6.6.2 Loading an update into the control ............................................................................................234

7 Client setup Analyze MyPerformance (AMP)......................................................................................... 237

7.1 Overview ....................................................................................................................................237

7.2 SINUMERIK Operate machines.................................................................................................237 7.2.1 Display the "SINUMERIK Integrate" softkey..............................................................................238 7.2.2 Enabling SINUMERIK Integrate applications.............................................................................238 7.2.3 Inhibiting SINUMERIK Integrate applications ............................................................................240 7.2.4 Installing the basis installation and AMP ...................................................................................241 7.2.4.1 Basis installation, installing Installer ..........................................................................................241 7.2.4.2 Basis installation, installing Base Setup ....................................................................................243 7.2.4.3 Installing the AMP application....................................................................................................246 7.2.5 Uninstalling the basis installation and AMP...............................................................................249 7.2.5.1 Uninstalling the AMP application ...............................................................................................249 7.2.5.2 Basis installation, uninstalling Base Setup ................................................................................251 7.2.5.3 Basis installation, uninstalling Installer ......................................................................................252

7.3 HMI-Advanced machines...........................................................................................................252 7.3.1 Installing SINUMERIK Integrate client .......................................................................................252 7.3.2 Stopping/starting SINUMERIK Integrate applications................................................................267 7.3.3 Changing, repairing and uninstalling programs .........................................................................269

7.4 Workstation PC ..........................................................................................................................274 7.4.1 Opening the PC client via Internet Explorer...............................................................................274

7.5 Variable logic..............................................................................................................................274 7.5.1 Introduction ................................................................................................................................274 7.5.1.1 Defining the logic using a text editor..........................................................................................275 7.5.1.2 Defining the logic using the application .....................................................................................276 7.5.1.3 Processing the MCIS-C file........................................................................................................277 7.5.2 Project processing .....................................................................................................................278

Table of contents


7.5.2.1 User interface............................................................................................................................ 278 7.5.2.2 Menu elements.......................................................................................................................... 279 7.5.2.3 Project settings.......................................................................................................................... 280 7.5.3 Logic elements .......................................................................................................................... 281 7.5.3.1 Inputs......................................................................................................................................... 281 7.5.3.2 Logic elements .......................................................................................................................... 282 7.5.3.3 Mathematical elements ............................................................................................................. 283 7.5.3.4 Comparison elements ............................................................................................................... 284 7.5.3.5 Complex elements .................................................................................................................... 286 7.5.3.6 Logic elements .......................................................................................................................... 290

A Annex A ................................................................................................................................................. 291

A.1 List of abbreviations .................................................................................................................. 291

A.2 840D sl documentation overview .............................................................................................. 294

Index...................................................................................................................................................... 295


Introduction 11.1 Product overview

Harmonized to address your particular requirements, you can access the various software modules of SINUMERIK Integrate. A total of six modules are available, which completely cover all aspects of machine integration into your communication, engineering and production processes.

Lock-it!

Run-it!

Create-

it!

Manage-it!

Access-it!

Analyze-it!

Creating and adapting user interfaces in SINUMERIKOperate

Organization and managementof NC programs andtools

G_N

C01

_DE

_005

29

Runtimes to runindividual screen interfaces with SINUMERIKRunning compile cycles on the NC kernel anddrives as well as thevirtual NC kernel (VNCK)

Remote access operations to the machine for diagnostics

Programming interfaces to the machine tool and server

Functions for condition-based maintenanceBased on key parametersAnalytical functions

Know-how protection for SINUMERIK

Creating your owncompile cycles within the frameworkof Open Architecture

Run-it!

Analyze-it! Access-it! Manage-it!

Create-it! Lock-it!

SINUMERIKIntegrate

The applications described in this manual are incorporated in the Manage-it!, Access-it! and Analyze-it! modules.

Modified application names In the process of launching SINUMERIK Integrate, the previous names of the applications were combined and given standard names under the new SINUMERIK Integrate brand label.

Introduction 1.1 Product overview


The following table provides you with a comparison regarding what the corresponding software solutions were previously called and what the new applications are called under SINUMERIK Integrate:

Previous name New name

SINUMERIK Integrate Manage-it! MCIS TDI Manage MyTools (MMT) MCIS DNC Manage MyPrograms (MMP) Access-it! MCIS ADDM Access MyBackup (AMB) Machine diagnostics via the Internet Remote STEP 7

Access MyMachine/Ethernet (AMM/E) Access MyMachine/STEP 7

Analyze-it! ePS Condition Monitoring Analyze MyCondition (AMC) MCIS MDA Analyze MyPerformance (AMP)

Example: System with Manage MyTools (MMT)

ServerManage MyToolsper connection "license per node"

SINUMERIK 840D slwith SINUMERIK OperateManage MyTools (Option)one option per connection

SINUMERIK 840Dwith HMI AdvancedManage MyTools (node)per connection one "license per node"

Operating PCs

G_NC01_DE_00467

Tool setting station (TSS)

SIMATIC S7

Tool stock

Introduction 1.2 Application areas and interaction


Example: System with Manage MyPrograms (MMP)

NC Program Management ServerManage MyPrograms (node)per connection one "license per node"

SINUMERIK 840D slwith SINUMERIK OperateManage MyPrograms (Option)one option per connection

Operator stationManage MyPrograms (node)per connection one "license per node"

Serial CNC machines/TSS Manage MyProgramsManage MyPrograms (node)per connection one "license per node"

SINUMERIK 840Dwith HMI AdvancedManage MyPrograms (node)per connection one "license per node"

G_N

C01

_DE

_004

65

1.2 Application areas and interaction To operate SINUMERIK Integrate, presently at least two physical servers are recommended depending on the number of machines that exist. The servers used reflect the main SINUMERIK Integrate functions and are summarized in the table below.

In order to integrate machine tools into SINUMERIK Integrate, depending on the computer version, various server and client setups are required.



SINUMERIK Integrate with Siemens server Below is an overview of the server/client installations when SINUMERIK Integrate is operated using the Siemens server.

Figure 1-1 Server/client installations



SINUMERIK Integrate with local server Below is an overview of the server/client installations required when SINUMERIK Integrate is operated using a local server.

Figure 1-2 Server/client installations

Server installation A distinction is made between the following versions when installing the server:

● Siemens server: Siemens provides this server, and customers do not have to install it. The software functions are retrieved via the Internet and global telecommunication infrastructures.

● Local server: In the local server mode, the server setup is directly installed at the customer. These server setups are installed once, and in some instances, used by several applications. For the procedure, please refer to Chapter: Installing/uninstalling the local server (Page 21)



The following overview table shows which setup for the server installation is required for which application.

Access MyBackup (AMB)

Analyze MyCondition (AMC)

Analyze MyPerformance (AMP)

Access MyMachine/ Ethernet (AMM/E)

Manage MyPrograms (MMP)

Manage MyTools (MMT)

Local server Server set up SINUMERIK Integrate AMB/ AMC/ AMP

X X X

Server setup MMT X Server setup MMP X Server setup AMP X

Client installation Depending on the version of your computer and operating software, the corresponding clients must be installed.

The following overview table shows which client setup is required on the computers for which application.

Access

MyBackup (AMB)


Analyze MyPerformance(AMP)




SINUMERIK Operate machine Basis installation: Installer Base Setup

X X X X

Client setup MMT X Client setup MMP X Client setup SINUMERIK Integrate AMB/ AMC/ AMP

X X X

Client setup AMM service mode (is only possible with SINUMERIK Operate on PCU 50)

X



Access MyBackup (AMB)


Analyze MyPerformance(AMP)




HMI-Advanced machine Client setup SINUMERIK Integrate SMC

X X X X

Client setup MMT X Client setup MMP X Client setup AMM service mode

X

Machine PC (IPC) Client setup X X Client setup MMT X Client setup MMP X Workstation PC Client setup AMM service engineer

X

Client setup MMT X Client setup MMP X Client setup AMP X Client setup AMC (Internet)

X

Client setup AMB (Internet)

X

Client setup AMM (ActiveX)

X

Introduction 1.3 System preconditions


1.3 System preconditions The tables below provide a summary of the base software absolutely necessary for operating SINUMERIK Integrate, depending on its user version. The use of other versions of the base software specified in the tables is not supported.

Hardware and software preconditions As a minimum, the following hardware and software preconditions must be fulfilled:

MMP / MMT AMC / AMB / AMP

AMM

Local server Processor from P IV from quad core RAM (GB) 21) 4 (per processor) Free hard disk space (GB)12)

15 30

Operating system Windows Server 2008 SP2 x64 Windows 7 x64 Windows Server 2003 SP2 x32 Windows XP SP3 x32

Windows Server 2008 SP2 x64 Windows 7 x64 Windows Server 2003 SP2 x32

Database SQL Server 2005 Express SQL Server 2008 R2 Express

SQL Server 2005 Express SQL Server 2008 R2 Express SQL Server 2008 R2 Professional

No data2)

Windows services Windows 2003: Internet Information Services (IIS) 6.0 Windows 2008: Internet Information Services (IIS) 7.5, Microsoft .NET Framework 3.5.1 Windows 7: Internet Information Services (IIS) 7.5, Microsoft .NET Framework 3.5.1

SINUMERIK Operate machine/ HMI-Advanced/ machine PC6) Hardware MMC1037)

from PCU 50.1 from NCU 7x0.2 (from SINUMERIK Operate 2.6. SP1 HF5)

from PCU 50.1 from NCU 7x0.2 (from SINUMERIK Operate 2.6. SP1 HF5)8)

from PCU 509) 10) 11)

RAM No data 256 MB (PCU) No data Database Applies to MMT:

Microsoft Access (Jet 4.0 SP8) MSDE 2000 SP3a

Internet Explorer (IE) No data from IE 6 (PCU) Screen resolution 640 x 480

800 x 600 1024 x 768 1280 x 768 1280 x 1024



MMP / MMT AMC / AMB / AMP

AMM

Workstation PC Processor from P IV (Windows XP)

1 GHz processor (Windows 7 x32/x64) RAM (MB/GB) 512 MB (Windows XP)

1 GB (Windows 7 x32) 2 GB (Windows 7 x64)

Free hard disk memory (GB)12)

No data2) 0,53)

Operating system Windows XP SP3 x32 Windows 7 x324) Windows 7 x644)

Internet Explorer (IE) - IE 65) from IE 7 and higher (in the comp. mode)

1) For operation without SINUMERIK Operate Support (server 4.12 is omitted), then the minimum required main memory space is reduced to 1 GB.

2) The server is operated by Siemens AG. As a consequence, no customer-specific system requirements are listed. 3) Service Mode Client (SMC): 0.015 GB; Service Engineer Client: 0.5 GB. 4) For machine (machine PC), the Windows 7 operating system is not supported. 5) Only Internet Explorer version 32 bit has been released for the service engineer client (Access MyMachine). 6) No data regarding the processor and operating system, as these parameters are given by the hardware components. 7) Only in conjunction with MMP! - MMC software as of SW Version 4.04.17 (only possible on request for a specific

project) under Windows 95 on MMC103. Note: There are function restrictions when using MMC103 (e.g. no archiving, no quick filter).

8) AMP, only from SINUMERIK Operate 4.5 SP2. 9) Restricted functional scope (conference, file transfer) from SINUMERIK Operate 2.6 SP1 HF5; full functional scope from

SINUMERIK Operate 4.4 SP4 and 4.5 SP2. 10) Restricted functional scope (conference, file transfer, session recording) from HMI-Advanced 6.1. STEP 7 is not

available for HMI-Advanced. 11) Service mode client is only possible from PCU 50.2 and higher. 12) In addition to the data provided, approx. 100 MB must be available on the operating system drive.



Firewall settings In order to permit an error-free connection between the Siemens server, local servers and the control systems, the following settings must be made:

Port / application MMP MMT AMC AMB AMP AMM 80/4431) X X X X X X 1352) O O O O O O 1080 X 14332) O O 14342) O O O O O O 23822) O O O O O O 3040 X 3050 X 40222) O O O O O O 80002) O

1) Port 80 for non-encrypted communication, otherwise port 443 (https). 2) If the personal firewall of the server is active, or if the SQL server is installed on a separate server, then the specified

ports must also be opened.

Port Description 80 (http) / 443 (https)

Communication between the Siemens server and the control system

135 Communication between SQL server and SQL debugger/RPC 1080 Communication MMP 1433 Communication between SQL server and MMT server 1434 Communication between SQL server and SQL server administration 2382 Communication between SQL server and SQL browser 3040 Communication between MMT server and HMI-Advanced machine 3050 Communication between MMT server and PC workstation 4022 Communication between SQL server and SQL service broker 8000 Communication between MMT server and Siemens server


Installing/uninstalling the local server 22.1 Introduction

Overview The local server is part of the SINUMERIK Integrate product portfolio. It is mainly intended for use by customers who require a high level of data confidentiality and would therefore be unwilling to store information in a location outside of their direct sphere of influence. Customers are completely responsible for the operation of SINUMERIK Integrate applications and the server systems required for these, with all aspects regarding availability, data security and the IT system administration as well as the IT infrastructure. Aspects that especially discuss the necessary IT-relevant tasks in the preparatory phase are described in this document. The graphics shown in this documentation serve for visualization purposes only.

Precondition You require the following access authorization to install and uninstall server setups: Protection level 1 (password: machine manufacturer).

Before installing a server, the Windows services must also be installed, refer to Chapter: Installing Windows services (Page 22).

Server installations The following server setups must be installed for the SINUMERIK Integrate applications MMT, MMP, AMB, AMC, and AMP:

● Server set up MMT, see Chapter: Installing the server setup MMT (Page 45)

● Server set up MMP, see Chapter: Installing the server setup MMP (Page 54)

● Server setup (AMP, AMB, AMC), see Chapter: AMP, AMC, AMB server (Page 61)

You can find an additional description for the SINUMERIK Integrate AMP application on the installation CD: "AMP configuration"

Installing/uninstalling the local server 2.2 Installing Windows services


2.2 Installing Windows services Before installing the local server, depending on your particular Windows version, you must install the following additional applications:

● Microsoft .NET Framework 3.5.1: Error-free functionality on the PC user interface.

● Internet Information Services (IIS) 6.0 The expansion ASP.Net 2.0 must be explicitly released under IIS 6 .

In so doing, a differentiation is made between the following Windows servers:

● Windows 2003 (only 32 bit)

● Windows 2008R2

● Windows 7

Regular software updates

The security patches supplied monthly by Microsoft are checked by the ASP server operator for compatibility with the current version of SINUMERIK Integrate using an internal system test and then released. An overview of the patch compatibility is generally given shortly after the release of the security patch on the Service & Support Portal of Siemens Industry Automation and Drive Technologies.

2.2.1 Under Windows Server 2003 32 bit Under Windows Server 2003, 32 bit, you require the Internet Information Services (IIS) 6.0.

This is installed via "Control Panel" - "Application Server" - "Add/Remove Programs" - "Add/Remove Windows Components" - "Application Server".



Installation 1. Under "Systems Properties", you can identify the "Microsoft Windows Server 2003"

server version.

2. Using "Start" - "Settings", open the "Control Panel" function.



3. Double-click to open "Add or Remove Programs".

The "Windows Components Wizard" window is opened, and shows you the components.

4. In the check box, set a checkmark for "Application Server" and click on the "Next >"

button.



5. Double-click again to open "Add or Remove Programs".

6. Under "Add/Remove Windows Components" select the "Screenshot Captor 3.08.01"

installation and click on "Remove".

7. This process takes some time and the following message is displayed:



8. In the Windows Components window, select "Application Server". Set the checkmark in the check box and click on "Next >.

9. The installation is prepared and the procedure is displayed on a progress bar.



10. The installation of the "Internet Information Services" component is displayed.

11. The following message is displayed after installation has been completed.

Click the "Finish" button to complete the installation.



Updates 1. Select the security updates for the Windows Server 2003.

Click on "Download" to start this process.

2. Again select "Add/Remove Windows Components".



3. Select "Properties"

4. In the footer a message is displayed that the update has been completed.

2.2.2 Under Windows Server 2008R2 Under Windows Server 2008 R2, 64 bit, you require the Internet Information Services (IIS) 7.5. The installation is realized via "Server Manager" - "Roles" - "Add Roles" - "Web Server (IIS)".

Further, you require Microsoft .NET Framework 3.5.1. Installation is realized via "Server Manager" - "Features" - "Add Features" - ".Net Framework 3.5.1 Features".



Installation 1. Double-click on "Server Manager" to open.

2. Select "Roles", and double-click on "Add Roles".

3. Select the "Before You Begin" function. You obtain an information window which informs

you about the security provisions. Click on "Next >" to continue.



4. Now select the "Server Roles" function. You obtain an overview of the components that are available. In the check box, set a checkmark for "Web Server (IIS)" and click on the "Next >" button.

5. Now select "Web Server (IIS)" to obtain detailed information about the version and

functionality. Click on "Next >".



6. Under "Web Server (IIS)", select the "Role Services" option. You obtain an overview of the activated common HTTP features. Click on "Next >" to continue.

7. Select "Confirmation" to obtain an overview of the selected components.

Click on "Install" to start the installation.



8. A display showing the installation progress is displayed under "Progress".

9. You obtain information about the results of the installation under "Results".

Click on "Close" to close the window.



Installing Microsoft .NET Framework 3.5.1 1. The server manager is opened.

Select the "Features" function and click on"Add Features".

2. The "Select Features" window is opened.

Set a checkmark in the check box ".NET Framework 3.5.1 Features".



3. Click on "More about features" to obtain more information required to install ".NET Framework 3.5.1 Features". Click on "Add Required Role Services" to continue.

4. ".NET Framework 3.5.1 Features" is selected.

Click on "Next >".



5. Now select "Web Server (IIS)" to obtain more information about the installed web server (ISS). Click on "Next >".

6. Now select "Role Services" to obtain more information about the environment of the

installed web server. Click on "Next >".



7. The selection of features is displayed under "Confirmation". Click on "Install" to start the installation.

8. A display showing the installation progress is displayed under "Progress".



9. You obtain information about the results of the installation under "Results". Click on "Close" to close the window.

10. You obtain an overview of the complete server installation under "Server Manager".



Installing updates 1. Via the icon, you obtain a message if updates are available.

2. The Windows Update window shows you the scope of the update.

Click on the link to obtain an overview.



3. You obtain an overview of the necessary updates. Click on "OK" to start the installation.

- OR - Click on "Install updates" to start the installation.



4. The progress is displayed.

5. You obtain a message about the result of the update.

Click on "Restart now" to reboot the computer.

2.2.3 Under Windows 7 Under Windows 7, you require Microsoft .NET Framework 3.5.1.

The installation is realized via "Control Panel " - "Programs and Features " - "Turn Windows Features on and off".

You also require Internet Information Service (IIS) 7.5. The installation is realized via "Control Panel " - "Programs and Features " - "Turn Windows Features on and off" - "Web Server (IIS)".



Installation 1. Click "Start".

2. Select "Control Panel".

3. Double-click on "Programs and Features" to open.



4. Select "Turn Windows features on or off."

5. The window with the available features is opened.

Select "Microsoft .NET Framework 3.5.1".



6. Then select "Internet Information Services". You then obtain information as to which services this installation includes.

7. Click on "OK" to confirm the selection.

Installing/uninstalling the local server 2.3 MMT server


8. This process can take some time. An appropriate message is displayed.

2.3 MMT server

2.3.1 Installing the server setup MMT With the installation on a PC, a fundamental distinction is made between a server and a client version. Depending on the selection, the same setup then installs a server or a client.

The additionally installed Windows services automatically start Manage MyTools as background service each time the computer is restarted.

Procedure 1. Start "Setup_MMT_PC.exe" from the installation directory of the installation CD or the local

copy of the installation directory on the computer. Manage MyTools - InstallShield Wizard is opened.

2. Select an installation language. This language selection is only binding for the installation. The following languages are listed:

– German

– English

Click "OK" to confirm the selection.



3. The welcome screen is opened. Click on "Next >" to start the installation preparation.

4. Click on "Display information" to view the information regarding the application in

"readme.rtf". Observe the notes. After you have read the information, click on "Next >".



5. The license agreement window opens. Read the license agreement. If you would like to print out the license agreement, click on "Print". Then select "I accept the terms of the license agreement" and click on "Next >".

6. The "Select product type" window opens.

Select the "Server" version.

Set the checkmark in the check box of "Support SINUMERIK Operate" when you connect a control system with SINUMERIK Operate to MMT. If you select the function, before installing MMT, you must install "Microsoft Internet Information Service (IIS)" on the PC, see Chapter: Installing Windows services (Page 22) The installation is automatically canceled if you select the "Support SINUMERIK Operate" and IIS was not installed. Click on the "Next >" button.

Note Subsequently setting the "Support SINUMERIK Operate" function

After the installation, it is not possible to activate the "Support SINUMERIK Operate" function.

However, if you wish to set the function, then you must perform the setup again. Click on "Change" and "Change program".

Set a checkmark in the check box of "Support SINUMERIK Operate" and carry out setup again.



7. The "Select installation path" window is opened.

Click "Next >" to accept the directories proposed by the setup. - OR - Click "Change ..." to change the installation directories.

Directory Meaning Manage MyTools software Archive for all executable applications and those required by

Manage MyTools. Data directory Archive for all files relevant for Manage MyTools .



8. All data of the Manage-it! module use a common database. Some tables of this database, for example, the user administration and plant hierarchy tables, are used by all applications. The SQL database is available as a free version on the installation CD and, depending on the selection, can be automatically installed and configured by the setup. A distinction is always made between a new installation or selecting an already installed database server. At the beginning of the installation, a check is made as to whether a database server has already been installed. If a database server has still not been installed on the target system, then version "SQL Server 2008 R2 SP1 Express" is installed by the setup. If an older version of a database is already installed, then you obtain an appropriate error message. Click "Next >" to start the installation of the database server and the configuration of the database tables. The database server is automatically allocated the name "(local)\MCIS".

Note • If a database server with the name "(local)\MCIS" was already installed on the target

system, then the installation of "SQL Server 2008 R2 SP1 Express" is skipped. • If an older version of a database is already installed, then you obtain an appropriate

error message.

The "Check database" window is opened.

– Accept the standard default settings in the "Database server that you are installing to" selection box.

– Select the connection type "Windows authentication of current user". - OR - Select the "SQL server authentication using the Login ID and password below". Enter the Login ID "sa" and the password "P4sa2odb!".

– Accept the listed database catalog "MCISDB". - OR - Click on "Browse...", to select another database catalog.

Click "Next >" to start the installation of the database server and the configuration of the database tables.



9. After the database link has been successfully checked, the "Start installation" window is opened. Click on the "Install" button to start the installation.

10. The installation is started and the procedure is displayed on a progress bar.



11. Click on "Finish" to complete the installation.

12. After the installation has been completed, a restart is required.

Click on "Yes" to automatically restart the computer. Click on "No" if you wish to manually start the computer at a later point in time.



Settings with MMC103/ PCU 50 with Windows NT If you connect SINUMERIK 840D control systems with MMC103 or PCU 50 with Windows NT to the server, for Windows 2008 or Windows 7, you must make the following settings:

1. Open "Local Security Policy" - "Local Policies" - "Security Options", and in the list, select the "Network Security policy: LAN Manager authentication level".

2. Open the properties window "Local Security Settings", and in the selection box, select

"Send LM & NTLM - use NTLMv2 session security if negotiated". Click on "OK" to confirm your selection.



2.3.2 Uninstalling the server setup MMT The installed server setup Manage MyTools is uninstalled in the control panel using "Change or Remove Programs".

Procedure 1. The "Add or Remove Programs" window is opened.

Select the setup "Manage MyTools" and click on "Remove".

2. You obtain a confirmation prompt as to whether you really wish to remove

Manage MyTools. Click on "No" to cancel the operation. Click on "Yes" to confirm the message.

3. The uninstallation is started and the procedure is displayed on a progress bar.

Installing/uninstalling the local server 2.4 MMP server


2.4 MMP server

2.4.1 Installing the server setup MMP With the installation on a PC, a fundamental distinction is made between a server and a client version. Depending on the selection, the same setup then installs a server or a client.

The additionally installed Windows services automatically start Manage MyPrograms as background service each time the computer is restarted.

Procedure 1. Start "Setup_MMP_PC.exe" from the installation directory of the installation CD or the local

copy of the installation directory on the computer. Manage MyPrograms - InstallShield Wizard is opened.


– German

– English





4. Click on "Display information" to view the information regarding the application in "readme.rtf". Observe the notes. After you have read the information, click on "Next >".

5. The license agreement window opens.

Read the license agreement. If you would like to print out the license agreement, click on "Print". Then select "I accept the terms of the license agreement" and click on "Next >".



6. The "Select product type" window opens. Select the "Server" version.

Set a checkmark in the check box of "Support SINUMERIK Operate" if you connect a control with SINUMERIK Operate to MMP. When selecting this function, before installing MMP on the PC, you must install "Microsoft Internet Information Service (IIS)", see Chapter: Installing Windows services (Page 22) The installation is automatically canceled if you select the "Support SINUMERIK Operate" and IIS was not installed.

Click on the "Next >" button.

Note Subsequently setting the "Support SINUMERIK Operate" function

After the installation, it is not possible to activate the "Support SINUMERIK Operate" function.

However, if you wish to set the function, then you must perform the setup again.

Click on "Change" and "Change program".

Set a checkmark in the check box of "Support SINUMERIK Operate" and carry out setup again.



7. The "Select installation path" window is opened. Click "Next >" to accept the directories proposed by the setup. - OR - Click "Change ..." to change the installation directories.

Directory Meaning Manage MyPrograms software

Archive for all executable applications and those required by Manage MyPrograms.

Data directory Archive for all the databases or configuration files relevant for Manage MyPrograms.



8. All data of the Manage-it! module use a common database. Some tables of this database, for example, the user administration and plant hierarchy tables, are used by all applications. The SQL database is available as a free version on the installation CD and, depending on the selection, can be automatically installed and configured by the setup. A distinction is always made between a new installation or selecting an already installed database server. At the beginning of the installation, a check is made as to whether a database server has already been installed. If a database server has still not been installed on the target system, then version "SQL Server 2008 R2 SP1 Express" is installed by the setup. If an older version of a database is already installed, then you obtain an appropriate error message. Click "Next >" to start the installation of the database server and the configuration of the database tables. The database server is automatically allocated the name "(local)\MCIS".

Note • If a database server with the name "(local)\MCIS" was already installed on the target

system, then the installation of "SQL Server 2008 R2 SP1 Express" is skipped. • If an older version of a database is already installed, then you obtain an appropriate

error message.


– Accept the standard default settings in the "Database server that you are installing to" selection box.

– Select the connection type "Windows authentication of current user". - OR - Select the "SQL server authentication using the Login ID and password below". Enter the Login ID "sa" and the password "P4sa2odb!".

– Accept the listed database catalog "MCISDB". - OR - Click on "Browse...", to select another database catalog.




9. After the database link has been successfully checked, the "Start installation" window is opened. Click on the "Install" button to start the installation.





12. After the installation has been completed, a restart is required. An appropriate message

is displayed.

2.4.2 Uninstalling the server setup MMP The installed server setup Manage MyPrograms is uninstalled in the control panel using "Change or Remove Programs".


Select the setup "Manage MyPrograms" and click on "Remove".

Installing/uninstalling the local server 2.5 AMP, AMC, AMB server


2. You obtain a confirmation prompt as to whether you really wish to remove Manage MyPrograms. Click on "No" to cancel the operation. Click on "Yes" to confirm the message.


2.5 AMP, AMC, AMB server For SINUMERIK Integrate AMP, AMC and AMB, for the server version, Windows services are also required, which automatically start as background service each time the computer is restarted.

See Chapter: Installing Windows services (Page 22)

If you restart the setup at a later point in time, SINUMERIK Integrate identifies the existing installation, and outputs an appropriate message or skips several installation steps.

Procedure 1. Start "SINUMERIK INTEGRATE°Setup.exe" from the installation directory of the

installation CD or the local copy of the installation directory on the computer.



2. The "Sinumerik Integrate - InstallShield Wizard" is opened. Select a language for installation. This language selection is only binding for the installation. The following languages are listed:

– German

– English


3. The welcome screen is opened.

Click on "Next >" to start the installation preparation.




5. The "Product selection and destination folder" window is opened.

In the upper area of the window, select the required applications by setting a checkmark in the check box.

– If you select "Analyze MyPerformance", then continue with step ⑧.

– If you select "Analyze MyCondition", then continue with step ⑥.

– If you select "Access MyBackup", then continue with step ⑦.

In the lower area of the window, accept the installation directory for the program and database recommended by setup. - OR - Click on "Change ...", to change the directories. Then click on "Next >".



6. If you select the "Analyze MyCondition"application, then the "Product selection and destination folder" window is opened with the following content.

– "Install render server" The render server is provided via the Siemens server, and must be used to support SINUMERIK Operate on NCU. Set a checkmark in the check box if you wish to integrate a NCU with SINUMERIK Operate into SINUMERIK Integrate. Accept the directory listed by setup. - OR - Click on the "Change.." button in order to select a different installation directory.

– "Host names to be accepted, separated by semicolons" In the text field, enter a corresponding host.

Click on "Next >" to confirm settings.



7. If you select the "Analyze MyCondition"application, then the "Product selection and destination folder" window is opened with the following content.

– "Install genesis" The genesis server is provided through the Siemens server and must be used to support SINUMERIK Operate on NCU. In the checkbox, set a checkmark if you wish to integrate an NCU with SINUMERIK Operate into SINUMERIK Integrate. Accept the directory listed by setup. - OR - Click on "Change..." to select another installation directory.

Click on "Next >" to confirm settings.

8. All SINUMERIK Integrate data use a common database. Some tables of this database,

for example, the user administration and plant hierarchy tables, are used by all applications. The SQL database is available as a free version on the installation CD and, depending on the selection, can be automatically installed and configured by the setup. A distinction is always made between a new installation or selecting an already installed database server. At the beginning of the installation, a check is made as to whether a database server has already been installed. If a database server has still not been installed on the target system, then version "SQL Server 2008 R2 SP1 Express" is installed by the setup. If an older version of a database is already installed, then you obtain an appropriate error message. Click "Next >" to start the installation of the database server and the configuration of the database tables. The database server is automatically allocated the name "(local)\MCIS".



Note Database server

If a database server with the name "(local)\MCIS" was already installed on the target system, then the installation of "SQL Server 2008 R2 SP1 Express" is skipped. If an older version of a database is already installed, then a corresponding error message is displayed.


– "Database server that you are installing to": Accept the database server specified by the system.

– Select the connection type "Windows authentication credentials of current user". - OR - Select the "SQL server authentication using the Login ID and password below". Enter the Login ID: "sa" and for the password: "P4sa2odb!".




9. The "Ready to install program" window is opened. Click on the "Install" button to start the installation.

10. The installation status is displayed in the following window.


12. After the installation has been completed, a warm restart is required. An appropriate message is displayed.




Client setup Manage MyTools (MMT) 33.1 Overview

Precondition The server installation MMT has been completed.

You require the following access authorization to install and uninstall client setups: Protection level 1 (password: machine manufacturer).

Overview The client installation of Manage MyTools (MMT) is described at the following workstations in the following chapters:

● Machine with SINUMERIK Operate

● Machine with HMI-Advanced

● Workstation PC

3.2 SINUMERIK Operate machine

Introduction With SINUMERIK Operate you directly install the SINUMERIK Integrate applications via the user interface of the control system.

Proceed as follows when installing for the first time:

1. Enable the "SINUMERIK Integrate" softkey on the user interface to start SINUMERIK Integrate.

2. Enable the use of SINUMERIK Integrate.

3. Start the basis installation "Installer" and "Base Setup". This installation is performed once. From the user interface, you can query as to whether the basis installation is already available.

4. Install the client setup of the application.

Client setup Manage MyTools (MMT) 3.2 SINUMERIK Operate machine


3.2.1 Display the "SINUMERIK Integrate" softkey The softkey on the user interface to call SINUMERIK Integrate, is activated using a display machine data.

Procedure 1. At the control, start the operating software SINUMERIK Operate.

2. Press the "Startup" softkey and then the "Machine data" softkey.

3. Press the menu forward key and press the "Display MD" softkey.

4. Set machine data MD9108 $MM_SINUMERIK_INTEGRATE to "1".

The "SINUMERIK Integrate" softkey is displayed on the extended horizontal softkey bar.

3.2.2 Enabling SINUMERIK Integrate applications When installing the applications for the first time, SINUMERIK Integrate is always stopped, and you must enable the applications.

When operating at the machine, you then have the possibility of stopping SINUMERIK Integrate.

See Chapter: Inhibiting SINUMERIK Integrate applications (Page 72)

Procedure 1. SINUMERIK Operate is started.

2. Press the menu forward key and press the "SINUMERIK Integrate" softkey.

If the softkey is not displayed in the horizontal bar, then you must first enable the softkey. See Chapter: Display the "SINUMERIK Integrate" softkey (Page 70)



The welcome window is opened.

3. Press the "Settings" softkey.

The "Settings" window opens displaying the system status "Use LOCKED".

4. Press the "Enable use" softkey to start SINUMERIK Integrate.

You obtain the safety prompt "Do you really wish to enable the use of SINUMERIK Integrate applications?“

5. Press the "OK" softkey to confirm the confirmation prompt.

The use of SINUMERIK Integrate applications is enabled.



- OR -

Press the "Cancel" softkey.

The applications are not enabled, and the previous window is displayed.

3.2.3 Inhibiting SINUMERIK Integrate applications You can stop SINUMERIK Integrate if, during operation at the machine, the applications are not required.

Procedure

1. The "Settings" window is displayed.

Use is enabled for SINUMERIK Integrate applications. Press the "Inhibit use" softkey to inhibit the applications.

2. You obtain the following confirmation prompt: "Do you really wish to inhibit the use of SINUMERIK Integrate applications?“


- OR -

Press the "Cancel" softkey so that SINUMERIK integrate is not

stopped.

4. After the applications have been inhibited, you receive the following message in the "Settings" window: "SINUMERIK Integrate use LOCKED".



3.2.4 Installing the basis installation and MMT

Introduction You start the basis installation and the client setup directly from the user interface.

Note the following sequence:

1. Basis installation, installing Installer (Page 73)

2. Basis installation, installing Base Setup (Page 75)

3. Installing the MMT application (Page 78)

3.2.4.1 Basis installation, installing Installer

Precondition The use of SINUMERIK Integrate applications must be enabled.

Procedure

The "Settings" window is displayed. Press the "Basis installation" softkey to identify as to whether the basis installation has already been made. You obtain a status message as to whether an installation is already available.

1.

If a basis installation is not available, then press the "Install" softkey.



2. The "Select basis installation" window opens and the directory overview is

displayed. If the data are on a USB FlashDrive, then navigate in the "USB" directory.Position the cursor to the "installer_xx_xx_xx_xx.tar.gz" file and press the "OK" softkey.

3. You will receive a message about the selected software, its directory and

its version. Now press the "OK" softkey to install the package. - OR - Press the "Cancel" softkey if you do not wish to install the selected package.



4. The installation is started and the procedure is displayed on a progress

bar. A message window is then displayed showing that the installation was successful. The title bar shows for which applications the basis installation is applicable. Press the "OK" softkey to complete the installation.

3.2.4.2 Basis installation, installing Base Setup

Precondition The basis installation, Installer is installed.

Installed applications The installed applications are displayed as overview in the "App-Installation" window.

Columns Meaning Application name Installed application Actual version Current version number Reference version Checkmark: Indicates that the actual version (effective version

= installed version) matches the reference version (nominal version).

Exclamation mark Reference and actual version do not match.



Procedure

1. The "Settings" window is displayed and the activated SINUMERIK

integrate applications are shown. Press the "App-Installation" softkey.

2. The "App-Installation" window is opened, and shows the applications that

have already been installed.

3. Press the "Install" softkey. The "Select basis installation" window opens and a directory overview is displayed.



4. If the data are on a USB FlashDrive for example, then navigate in the

"USB" directory. Position the cursor on the "basesetup_xx_xx_xx_xx.tar.gz" file and press the "OK" softkey. You obtain a safety note that you must confirm. The installation is started and the procedure is displayed on a progress bar.

5. You will then obtain a message confirming this, and the installed

application is shown under "Application is installed". Press the "OK" softkey to obtain an overview of the applications that have been installed.

6. The "App-Installation" window is displayed showing the applications that have already been installed along with the associated details.

7. If you wish to obtain additional information on the individual applications,

select the application and press the "Details" softkey.

8. Restart the control again to activate the applications.



3.2.4.3 Installing the MMT application

Precondition The basis installation of Installer and Base Setup has been completed.





Procedure





2. The "App-Installation" window is opened, and shows the applications that have already been installed.

3. Press the "Install" softkey.

The "Select basis installation" window opens and a directory overview is displayed.

4. If the data are on a USB FlashDrive, then navigate in the "USB" directory.

Position the cursor to the "manage_mytools_xx_xx_xx_xx.tar.gz" file and press the "OK" softkey. You obtain a safety note that you must confirm. The installation is started and the procedure is displayed on a progress bar.









3.2.5 Uninstalling the basis installation and MMT

Introduction You must observe the following sequence in order to uninstall the application:

1. Uninstalling the MMT application (Page 80)

2. Basis installation, uninstalling Base Setup (Page 82)

3. Basis installation, uninstalling Installer (Page 83)

3.2.5.1 Uninstalling the MMT application

Procedure

1.

The "App-Installation" window is opened and shows the existing applications. Select the "Manage MyTools" application and press the "Uninstall" softkey.



2. The following confirmation prompt is displayed: "Do you really wish to uninstall this application: Manage MyTools". Press the "OK" softkey to remove the package. The process is displayed in a progress bar.

- OR -

Press the "Cancel" softkey to prevent the uninstallation.

3. After the "Uninstallation was successful" message, restart the control system. To do this, press the "OK" softkey.



3.2.5.2 Basis installation, uninstalling Base Setup

Procedure

1. Press the "App-Installation" softkey.

The overview of the installed applications is displayed in the list.

2.

Select "Base Setup" and press the "Uninstall" softkey.

3. The following confirmation prompt is displayed: "Do you really wish to uninstall this application: Base Setup" Press the "OK" softkey to remove the package. The process is displayed in a progress bar.

- OR -





3.2.5.3 Basis installation, uninstalling Installer

Procedure



2.

Select the "Installer" package and press the "Uninstall" softkey.

3. The following confirmation prompt is displayed: "Do you really wish to uninstall this application: Installer" Press the "OK" softkey to remove the package. The process is displayed in a progress bar.

- OR -



Client setup Manage MyTools (MMT) 3.3 HMI-Advanced machine


3.3 HMI-Advanced machine

3.3.1 Installing MMT SINUMERIK

Precondition Before you start the installation, you require a database software.

Note Database software

Download the necessary database software from Microsoft, see Chapter: System preconditions (Page 18)

Procedure 1. Start the PCU in the Windows service mode.

2. Start "Setup_MMT_Sinumerik.exe" from the installation directory of the installation CD, the network drive, the USB flash drive or the local copy of the installation directory on the computer. Manage MyTools - InstallShield Wizard is opened.


– German (Germany)

– English (United States)





5. Click on "Display information" to view the actual "readme.rtf" about the application.

Observe the notes. After you have read the information, click on "Next >".




7. The installation directory, in which the application will be installed is displayed in the next

window. Click on "Next >" to accept the directory suggested by setup.



8. In the next dialog, select a database system for the installation.

– If you have installed "MS Access" as a database system, select "MS Access" and click on "Next >". Continue with step ⑪.

– If you have installed "MSDE 2000"as a database system, then select "MS SQL Server 2000 Desktop Engine (MSDE 2000)" and click on "Next >". Continue with step ⑨.

9. The "Database Server" window is displayed.

Select the database server on which you wish to make the installation as well as the authentication method.

10. Click "Next >" to start the installation of the database server and the configuration of the

database tables.



11. In the "Softkey selection" window you define the softkey which you use to start the Manage MyTools application. The free horizontal softkeys are listed in a selection box. Select the softkey, and click on "Next >".

12. The Wizard is ready to start the installation.

Click "Install" to start the installation.







15. A warm restart is required after installing Manage MyTools. Restart the control system.

3.3.2 Uninstalling MMT SINUMERIK The installed client setup Manage MyTools SINUMERIK is uninstalled in the control panel using "Change or Remove Programs".


Select the setup "Manage MyTools" SINUMERIK and click on "Remove".


"Manage MyTools SINUMERIK. Click on "No" to cancel the operation. Click on "Yes" to confirm the message.


Client setup Manage MyTools (MMT) 3.4 Workstation PC


3.4 Workstation PC

3.4.1 Installing MMT on a PC If Manage MyTools is installed as a client on a workstation PC, this is an HMI application. This version is not an active part of the plant hierarchy and therefore cannot be configured in the configuration.

Precondition In order to set up users and machines on the local server, Internet Explorer is required on the workstation PC.

Please refer to the following chapter regarding which Internet Explorer is suitable for your PC: System preconditions (Page 18)

Installation sequence 1. Start "Setup_MMT_PC.exe" from the installation directory of the installation CD or the local

copy of the installation directory on the computer.


– German

– English





4. Click on "Display information" to view the information regarding the product in

"readme.rtf". Observe the notes. After you have read the information, click on "Next >.





Select the "Operating PC" version. Installation is performed on a Windows PC with the version as Manage MyTools.



7. The "Select installation path" window is opened. Click "Next >" to accept the directories proposed by the setup. - OR - Click "Change ..." to change the installation directories.

Directory Meaning Manage MyToolssoftware Archive for all executable applications and those required

by Manage MyTools . Data directory Archive for all the databases or configuration files

relevant for Manage MyTools .

8. The "Start installation" window is displayed.

Click the "Install" button to start the installation.





11. After the installation of Manage MyTools, a restart is required.



3.4.2 Uninstalling MMT on a PC The installed client setup Manage MyTools is uninstalled in the control panel using "Change or Remove Programs".


Select the setup "Manage MyTools" and click on "Remove".

2. You obtain a confirmation prompt as to whether you really wish to remove Manage MyTools. Click on "No" to cancel the operation. Click on "Yes" to confirm the message.



Client setup Manage MyPrograms (MMP) 44.1 Overview

Precondition The server installation MMP has been completed.

You require the following access authorization to install and uninstall client setups: Protection level 1 (password: machine manufacturer).

Overview The client installation of Manage MyPrograms (MMP) is described at the following workstations in the following chapter:



● Machine PC

● Workstation PC

4.2 SINUMERIK Operate machines







Client setup Manage MyPrograms (MMP) 4.2 SINUMERIK Operate machines

























- OR -




Procedure





- OR -


stopped.




4.2.4 Installing the basis installation and MMP





3. Installing the MMP application (Page 106)



Procedure


1.




















Procedure


















4.2.4.3 Installing the MMP application



Columns Meaning Application name Installed application Actual version Current version number Reference version Checkmark: Indicates that the actual version (effective version =

installed version) matches the reference version (nominal version).

Exclamation mark

Reference and actual version do not match.

Procedure

1. The "Settings" window is displayed and the use of SINUMERIK integrate

applications is enabled. Press the "App-Installation" softkey.





The "Select basis installation" window opens and a directory overview is displayed.

4. If the data are, for example, on a USB flash drive, navigate in the "USB"

directory. Position the cursor on the "manage_myprograms_xx_xx_xx_xx.tar.gz" file and press the "OK" softkey. - OR - Navigate in the directory /System CF Card/addon Position the cursor to the "manage_myprograms_xx_xx_xx_xx.tar.gz" file and press the "OK" softkey. The installation is started and the procedure is displayed on a progress bar.

5. You will then obtain a message confirming this, and the application is

shown under "Application is installed". Press the "OK" softkey to obtain an overview of the applications that have been installed.







4.2.5 Uninstalling the basis installation and MMP


1. Uninstalling the MMP application (Page 108)



4.2.5.1 Uninstalling the MMP application

Procedure

1.

The App-Installation window is opened. Select the "Manage MyPrograms" application and press the "Uninstall" softkey.



2. The following confirmation prompt is displayed: "Do you really wish to uninstall this application: Manage MyPrograms". Press the "OK" softkey to remove the package. The process is displayed in a progress bar.

- OR -






Procedure



2.



- OR -






Procedure



2.



- OR -



Client setup Manage MyPrograms (MMP) 4.3 HMI-Advanced machine



4.3.1 Installing MMP SINUMERIK

Precondition Before you start the installation, you require a database software.

Note Database software

Download the necessary database software from Microsoft, see System preconditions (Page 18)

Procedure 1. Start the PCU in the service mode.

2. Start "Setup_MMP_Sinumerik.exe" from the installation directory of the installation CD or the local copy of the installation directory on the computer.


– German

– English




4. This welcome screen is opened. Click on "Next >" to start the installation preparation.






7. The installation path, in which the application will be installed is displayed in the next

window. Click on "Next >" to accept the directory suggested by setup.



8. In the "Softkey selection" window you define the softkey which you use to start the Manage MyPrograms application. The free horizontal softkeys are listed in a selection box. Select the softkey position, and click on "Next >".

9. The Wizard is ready to install the program.

Click "Install" to start the installation.








4.3.2 Uninstalling MMP SINUMERIK The installed client setup Manage MyPrograms SINUMERIK is uninstalled in the control panel using "Change or Remove Programs".


Select the setup "Manage MyPrograms SINUMERIK" and click on "Remove".


Manage MyPrograms SINUMERIK. Click on "No" to cancel the operation. Click on "Yes" to confirm the message.


Client setup Manage MyPrograms (MMP) 4.4 Workstation PC


4.4 Workstation PC

4.4.1 Installing MMP on a PC


Please refer to chapter System preconditions (Page 18) regarding which Internet Explorer is suitable for your PC.

Procedure 1. Start "Setup_MMP_PC.exe" from the installation directory of the installation CD or the local

copy of the installation directory on the computer.


– German

– English




3. This welcome screen is opened. Click on "Next >" to start the installation preparation.

The installation is prepared.







Select the "Operating PC" version. Installation is performed on a Windows PC with the version as Manage MyPrograms.



7. The "Select installation path" window is opened. Click "Next >" to accept the directories proposed by the setup - OR - Click "Change ..." to change the installation directories.

Directory Meaning Manage MyPrograms software Archive for all executable applications and

those required by Manage MyPrograms. Data directory Archive for all the databases or configuration

files relevant for Manage MyPrograms.

8. The Wizard is ready to install the program. Click the "Install" button to start the installation.






4.4.2 Uninstalling MMP on a PC The installed client setup Manage MyPrograms is uninstalled in the control panel using "Change or Remove Programs".


Select the setup "Manage MyPrograms" and click on "Remove".

2. You obtain a confirmation prompt as to whether you really wish to remove Manage MyPrograms. Click on "No" to cancel the operation. Click on "Yes" to confirm the message.



Client setup Access MyBackup (AMB), Analyze MyCondition (AMC) 55.1 Overview

Precondition You require the following access authorization to install and uninstall client setups: Protection level 1 (password: machine manufacturer).

Overview The client installation of Access MyBackup (AMB) and Analyze MyCondition (AMC) at the following workstations is described in the subsequent chapter:



● Machine PC

● Workstation PC

5.2 SINUMERIK Operate machine




Client setup Access MyBackup (AMB), Analyze MyCondition (AMC) 5.2 SINUMERIK Operate machine




















- OR -






Procedure





- OR -


stopped.




5.2.4 Installing the basis installation



Procedure


1.




















Procedure


















5.2.5 Uninstalling the basis installation


Procedure



2.



- OR -






Procedure



2.



- OR -



Client setup Access MyBackup (AMB), Analyze MyCondition (AMC) 5.3 HMI-Advanced machine



5.3.1 Installing SINUMERIK Integrate client The SINUMERIK Integrate client contains the setup of the Analyze MyPerformance (AMP), Analyze MyCondition (AMC) and Access MyMachine (AMM) applications.

If the SINUMERIK Integrate client has already been installed, then the system identifies the scope of the installation. When compared to a new installation, several installation steps are skipped, see Chapter: Configuring SINUMERIK Integrate client (Page 196).

The procedure when installing for the first time is explained below.

Procedure 1. Start "setup.exe" from the installation directory of the installation CD or the local copy of

the installation directory on the computer. English is the installation language. The welcome screen is opened. Click on "Next >".



2. The "License Agreement" window opens. Read the license agreement. Click on "Print" if you wish to print out the conditions. Then select "I accept the terms of the license agreement" and click on "Next >". - OR - If you click on "< Back", then you return to the previous window.

3. You then have the option of selecting between two installation types:

– Standard mode The preconfigured settings are used.

– Expert mode The preconfigured settings can be changed to meet individual requirements.

Select the "Standard mode" and click on "Next >".



- OR - Select the "Expert mode (with additional installation options)" and click on "Next >".

4. The "Controller configuration" window is opened

Select "SINUMERIK" and click on "Next >".



5. The SINUMERIK connection types are displayed in the "Controller configuration" window. If you are working in a networked environment, select "HMI-Advanced and SINUMERIK 840D/Di or 810D + PCU50/70". - OR - If separately integrated, e.g. via HMI Pro, then select "SINUMERIK with own integration".

6. Select the connection type in the next window:

– "1:1" The function allows a direct connection to the machine to be established.

– "1:N" The function allows a connection in a group with several machines.

– "Flying HMI": The function allows the use of SINUMERIK Integrate at machines, on which a client cannot be installed, because the operating software of the machine does not support this client. In this case, SINUMERIK Integrate is installed and configured on a workstation PC or machine PC (IPC). PC/IPC and machine communicate via a (W)LAN connection.



Select connection type 1:1 and then click on "Next >".

7. The "Additional Products" window is opened.

Select these options only if you wish to install the Access MyMachine (AMM) application, see Chapter: Configuring SINUMERIK Integrate client (Page 196). Click on "Next >".



8. If you have selected the "Standard mode" installation type, then the "Reconfigurable parameters" window is opened. You can select the following configuration:

– "HMI Softkey to start the product on the machine": After selecting this function, you can define the softkey position on the user interface.

– "Internet proxy configurations": After selecting this function, you can enter the interface to the Internet.

Click on "Next >".



9. If you select the "HMI Softkey to start the product on the machine", then the "Available Hotkeys" window is opened. From the drop-down list, select the position of the softkey with which you wish to start the application on the user interface. Click on "Next >".

- OR - Under step ③, if you selected installation type "Expert mode", then the "Choose Destination Location" window is opened. The installation directory is displayed. If you wish to use another directory, then press on the "Change..." button and enter the required directory.



10. If you selected the installation type "Expert mode", then the "Reconfigurable parameters" window is displayed. For the individual configuration options, please refer to Chapter: Configuring user-specific parameters - expert mode (Page 149).

11. The "SINUMERIK Integrate URL configuration" window is opened.

Here, you define URLs of SINUMERIK Integrate only if you install Access MyMachine (AMM), see Chapter: Configuring SINUMERIK Integrate client (Page 196).



12. In the following message window you are only requested to check the address settings. Confirm the note to check the Internet settings with "OK".

13. This opens the window "Internet Properties".

The address is specified under the "General" tab, in order to create the start page tabs. Click on the "Connections" tab in order to set up the Internet connection, and configure the LAN settings, see Chapter: Configuring Internet access (Page 153). Use the connection in your company network that has already been set up. Click on "OK".



14. After this, the message window "Detected internet connection settings" is opened and shows the actual settings. Click on "< Back" to correct the settings. Click on "Next >", to continue.

15. The settings are subject to an additional check, and in the "Detected Internet Security

Settings" window you obtain an appropriate message. Click on "< Back" to change the settings in the Internet Explorer. - OR - Click on "Next >" to continue.



16. The "Generic Driver Support" window is opened. Additional devices can be linked in here, see Chapter: Selecting a driver (Page 155). Select "OPC driver" and click on "Next >".

17. The window "Data transfer area location" opens and shows you the archive directory for

the transfer data. Click on "Browse..." if you wish to create another directory. Click on "Next > to continue.



18. The "Data transfer backup area location" window is opened, and shows you the archive directory for the temporary data, see Chapter: Changing the target directory data buffering (Page 158). Click on "Browse..." if you wish to create another directory. Click on "Next > to continue.

19. The "Log directory location" window is opened, and shows you the archive directory for

the log data, see Chapter: Changing the log file target directory (Page 159). Click on "Browse..." if you wish to create another directory. Click on "Next > to continue.



20. The "Data transfer area and logging settings" window is opened. Here you define where data is saved if an Internet connection develops a fault, see Chapter: Changing data volumes and protocol settings (Page 156). Enter the maximum data size for the transfer data, and click on "Next".

21. The "Boot script download strategy" window is opened.

You can select one of three different strategies for the download, see Chapter: Changing the download method for the boot script (Page 161). Click on "Next >".



22. The "Startup parameter configuration" window is opened. Select the start properties of the client, see Chapter: Changing the start parameter client (Page 162). Click on "Next >".

23. The "Time master settings for the machine" window is opened.

Here you can change the time synchronization/alignment between the PLC and HMI, see Chapter: Changing the time synchronization between PLC and HMI (Page 164). Set a checkmark for "Use HMI as time master" if you wish to activate the time synchronization. Click on "Next >".



24. The "Start copying files" window is opened and provides you with an overview of the settings that you have made. Click on "Next >" to start the installation.

25. The "Maintenance Complete" window is displayed.





5.3.2 Configuring user-specific parameters - expert mode

5.3.2.1 Overview of the expert mode The overview indicates the preconfigured settings, which you can change in the expert mode.

Expert mode

Table 5- 1 Overview of the expert configuration

Function Default setting IAC: https://www.epsnetwork.com/Services/HMI 1 Changing the URLs of the client MHComm: https:// www.epsnetwork.com/Services/MHC/Mhcomm.asmx

2 Configuration for the Internet access - Maximum size (MB): 100 3 Size of the local data volume Maximum files: 5000

4 Directory path for data transfer C:\...\HMI-Advanced\add_on\temp\MhDtsTmp 5 Directory path, log file C:\...\HMI-Advanced\add_on\MH\log 6 Select download method, boot script Offline mode ON, no repeat attempts to download the boot script from the

server ✔ Activate services 7 Startup parameters ✔ Automatically start SINUMERIK Integrate Client on the machine at

startup TimeAdjustInterval 3600 8 Time synchronization between PLC and

HMI TimeReadyOK 300

Note Expert mode

If, in the "Installation mode" window, you select the "Expert mode" function, then the installation wizard guides you through all of the options one after the other, which can be set in a user-defined fashion.

You can save time if you install the client in the standard mode and then carry out all of the user-defined settings.

See also Changing the URLs of the client (Page 150)

Configuring Internet access (Page 153)

Selecting a driver (Page 155)

Changing data volumes and protocol settings (Page 156)



Changing the target directory data buffering (Page 158)

Changing the log file target directory (Page 159)

Changing the download method for the boot script (Page 161)

Changing the start parameter client (Page 162)

Changing the time synchronization between PLC and HMI (Page 164)

5.3.2.2 Changing the URLs of the client You define the URLs of SINUMERIK Integrate using this function.

SINUMERIK Integrate URLs 1. The "Reconfigurable parameters" window is open.

In the checkbox, set a checkmark for "SINUMERIK Integrate URLs" and click on "Next >".



2. The "SINUMERIK Integrate URL configuration" window is opened. You define the URLs of SINUMERIK Integrate here. For the address data, a distinction is made between a connection to the Siemens server or a connection to a local server within a company network. If you install both "Access MyMachine (without Service Mode Client)" and "Service Mode Client" applications, then you must enter the following URLs: Establish a connection to the Siemens server:

– The display /Homepage/ HMI application - UI for machines client Display home page: https://www.epsnetwork.com/services/HMI/

– Render server is necessary to display the web pages on the control. Render service: https://render.epsnetwork.com/IERenderService/HandshakeService.asmx

– The web server is the communication interface on the server, which is addressed by the client. Web service: https://www.epsnetwork.com/Services/MHC/MHComm.asmx

Establish a connection to the local server:

– Display home page: http://<servername or ip>/mcis_if/HMI

– Render service: http://<servername or ip>/IERenderService/HandshakeService.asmx

– Web service: http://<servername or ip>/mcis_if/MHComm/MHComm.asmx



If you only install "Service Mode Client", then you must enter the URLs "IAC" and "MHComm": Establish a connection to the Siemens server:

– IAC (InterActive Client): Address to display the user interface of SINUMERIK Integrate IAC: https://www.epsnetwork.com/services/HMI/IAC

– MHComm (Machine Handler Communication):Address for the data communication from SINUMERIK Integrate MHComm: https://www.epsnetwork.com/Services/MHC/MHComm.asmxV

Establish a connection to the local server:

– IAC: http://<servername or ip>/mcis_if/HMI

– MHComm: http://<servername or ip>/mcis_if/MHComm/MHComm.asmx



5.3.2.3 Configuring Internet access You define the download method using this function.

Internet proxy configurations 1. The "Reconfigurable parameters" window is open.

In the checkbox, set a checkmark for "Internet proxy configurations" and click on "Next >".

2. Confirm the note regarding checking the Internet settings with "OK".



3. This opens the "Internet Properties" window. Use the connection in your company network that has already been setup and confirm the settings with "OK".

4. Select the "Connections" tab.

Under LAN settings, click on the button with the same name. The "Local Area Network (LAN) Settings" window is opened. Set a checkmark in the checkbox "Use automatic configuration script" to use the automatic configuration script. Use a connection in your company network that has already been set up Confirm your selection with "OK".



5. A window to check your settings is displayed. Confirm with "Next > - OR - Change the settings by returning to the Windows that was previously displayed using "< Back".

5.3.2.4 Selecting a driver Use this function to specify the access method for data exchange.

Generic Driver Support 1. The "Reconfigurable parameters" window is open.

In the checkbox, set a checkmark for "Generic Driver Support" to define the server driver and click on "Next >".



2. In the following window, under "Available Driver", you are given a selection of server drivers. Select the corresponding driver. In order to be able to address variable monitors, in the "Identifier (ProgID or CLSID)" entry field, enter the ID of the selected driver. You can define the driver ID in the driver documentation. Confirm your selection with "Next >".

5.3.2.5 Changing data volumes and protocol settings Using this function you define where data is saved if an Internet connection develops a fault.

Data volumes and protocol settings 1. The "Reconfigurable parameters" window is open.

In the checkbox, set a checkmark for "Data transfer area and logging settings" and click on "Next >".



2. If there is an Internet connection error during data transfer to the server, data is locally saved in order to continue data transfer once the connection has been restored.

– In the entry field "Maximum size (MB)", enter a value between 0 and 2000 MB.

– In the entry field "Maximum files" enter the maximum number of files that should be locally saved.

– If you enter a checkmark in the checkbox "Enable limiting number of files for logging", under "Maximum files", enter the maximum number of files that should be saved in the log file.

Confirm your entries by clicking "Next".

Option "MAXFILECOUNT"

Note

In addition, you have the possibility of limiting the number of files in the directory "MHDTS" using the option "MAXFILECOUNT" in the "settings.ini" file:

[APP]

; Maximum directory size [byte]

MAXDIRSIZE = 104857600

; Maximum "*.DTS" files in folder, additionally "*.TMP" with same amount.

MAXFILECOUNT = 1000



5.3.2.6 Changing the target directory data buffering You define in which directory the data in operation is saved using this function.

Data transfer area location 1. The "Reconfigurable parameters" window is open.

In the checkbox, set a checkmark for "Data transfer area and location" and click on "Next >".

2. In the defined directory, all of the data in operation are buffered until they are uploaded to

the server. Click on "Browse..." to select a new, local target directory. Confirm the change with "Next" >.



Note Constraint

It is not possible to buffer data in target directories that are located on network drives.

5.3.2.7 Changing the log file target directory You define in which directory the log files are saved using this function.

Log directory location 1. The "Reconfigurable parameters" window is open.

In the check box, set a checkmark for "Log directory location" and click on "Next >".

2. All log files are saved in the defined directory.

Click on "Browse..." to select a new, local target directory for the log files.



Confirm the change with "Next" >".

Note Constraint

It is not possible to save log files in target directories, which are located on network drives.



5.3.2.8 Changing the download method for the boot script You define the download method for the boot script using this function.

Boot script download strategy 1. The "Reconfigurable parameters" window is open.

In the checkbox, set a checkmark for "Boot script download strategy" and click on "Next >".

2. The following settings are available:

– "Offline mode ON, no repeated attempts to download the boot script from the server" A single attempt is made to load the boot script from the server. If there is no Internet connection, then the locally saved boot script is used.

– "Offline mode OFF, the client performs repeated attempts to download the boot script from the server" Several attempts are made to load the boot script from the server. If there is no Internet connection, a local boot script is not used.

– "Offline mode OFF, no repeated attempts to download the boot script from the server" A single attempt is made to load the boot script from the server. If there is no Internet connection, then the locally saved boot script is used.

Note Offline mode OFF

If the "Offline mode OFF" option is set, alarms that occur are not buffered and are lost.

Select the preferred method to download the boot script, by clicking the appropriate option field.



Confirm the selection with "Next" >.

5.3.2.9 Changing the start parameter client You define the start properties of SINUMERIK Integrate client using this function.

SINUMERIK Integrate Client startup parameters 1. The "Reconfigurable parameters" window is open.

In the check box, set a checkmark for "SINUMERIK Integrate Client startup parameters" and click on the "Next >" button.



2. The following settings are available:

– "Deferred startup of SINUMERIK Integrate Client" SINUMERIK Integrate client starts delayed by the specified time (0 - 300 s).

– "Slow internet connection" The SINUMERIK Integrate client delays establishing the Internet connection if there is slow access (analog modem, ISDN, modem/router).

– "Start of SINUMERIK Integrate Client" Activating/deactivating SINUMERIK Integrate. Activating/deactivating the automatic start of the SINUMERIK Integrate client when PCU, PC or PG powers up. Activating/deactivating the welcome screen while SINUMERIK Integrate is loaded.

Select the start parameters and confirm your selection with "Next >".



5.3.2.10 Changing the time synchronization between PLC and HMI Using this function you can change the time synchronization/alignment between the PLC and HMI.

Time master settings 1. The "Reconfigurable parameters" window is open.

In the check box, set a checkmark for "Time master settings" and click on "Next >".

● If an alarm is output at the control, this alarm is displayed with the PLC time.

Because the HMI and PLC time can deviate from one another, the operating software provides a function to synchronize/align both of these times. This function is also used by SINUMERIK Integrate. An error message is displayed if you enter values that are too low.

– Click in the check box "Use HMI as time master" to activate time synchronization. The entry fields to set the time intervals are enabled.

– For "TimeAdjustInterval" enter the time in seconds, which should elapse until the difference between the HMI and PLC time is saved in the operating software. An error message is displayed if you enter values that are too low.

– For "TimeReadOK", enter the time in seconds that should elapse until the next interval for time synchronization starts. An error message is displayed if you enter values that are too low.



Confirm your entries with "Next" >".

5.3.3 Integrating the client setup as external applications

Introduction You have the option of calling the client setup from other applications, e.g. via TRANSLINE 2000 HMI PRO CS.

The call is configured via the TRANSLINE user interface.

Setup client with HMI-Advanced

Within the external application, a softkey must be configured, which starts the "iac.exe" file.

Setup client without HMI-Advanced

Within the external application, the "MhCtrlr.exe" file must be configured as a background process with the name "MhController".



Example: Setup client with HMI-Advanced 1. Select the menu "Configuration" and "Function keys".

The following window is opened.

– Under "New image", enter the softkey name, e.g. "EXE".

– Define the softkey position using the <Shift> key + right mouse click.

– In the selection list "HMI images", select the function "Integrate EXE.".

2. Make the other settings as follows:

– In the option field, select "Standard EXE".

– In the text field "Exe (path and file):" enter the following directory: "f:\add_on\IAC.exe"

– In the text field "Windows title:" enter the title: "SINUMERIK Integrate"



Example: Setup client without HMI-Advanced 1. Select the menu "Configuration" and "Start background processes".

The following window is opened.

– In the text field "Exe (path and file):" enter the following directory: "f:\add_on\MhCtrlr.exe".

– In the text field "Windows title" enter the following title: "MhController"

Note

It is not permissible that "MhCtrlr.exe" is started as background process, if the .exe is started as background task by the Regie (administrator) (e.g. Task88).

While installing in the control, ensure that the following connection type is not selected: "HMI-Advanced and SINUMERIK 840D/Di or 810D + PCU50/70".



2. Select the menu "File" and "Setting target computer", to configure the transfer of the project to the target computer, e.g. to the PCU.

– Select the menu "File" and "Installation of the system on PCU". The TRANSLINE

system is transferred to the selected PCU and installed on the PCU with the HMI PRO setup.

– Select the menu "File" and "Installation of the project on PCU". The TRANSLINE project is transferred to the selected PCU and installed on the PCU with the HMI PRO setup.

5.3.4 Changing, repairing and uninstalling programs In an existing client setup, you have the option of changing, repairing or uninstalling installations.


the installation directory on the computer.

2. The "Welcome" window opens and offers you the following options:

– Changing the client setup

– Repairing the client setup

– Removing the client setup



Changing the client setup 1. In the "Welcome" window, select the "Reconfigure" function if you wish to change the

client version.

2. The next steps are described in the following section: Configuring SINUMERIK Integrate

client (Page 196).

Repairing the client setup 1. In the "Welcome" window, select the "Repair" function if applications are corrupted and

you wish to restore the initial state. Click on "Next >".



2. The "Setup Status" window opens and the operation is shown with a progress display.




Removing the client setup 1. In the "Welcome" window, select the "Remove" function if you want to remove the client

setup. Click on "Next >".

2. A confirmation prompt is displayed.

Confirm this message with "Yes" if an additional application, e.g. AMM is installed, and you wish to uninstall this application.

3. You obtain an additional confirmation prompt as to whether you wish to uninstall the

Service Mode Client application. Click on "Yes" to start this operation.



4. The uninstallation is started and the operation is displayed on a progress bar.

5. Click on "Finish" to complete uninstalling.

Client setup Access MyBackup (AMB), Analyze MyCondition (AMC) 5.4 Machine PC


5.4 Machine PC

5.4.1 Installing SINUMERIK Integrate client (IPC) SINUMERIK Integrate client includes the applications Analyze MyPerformance (AMP), Analyze MyCondition (AMC) andAccess MyMachine (AMM). If the SINUMERIK Integrate client has already been installed, then the system identifies the scope of the installation. When compared to a new installation, several installation steps are skipped.

The procedure when installing for the first time is described below.



2. The "License Agreement" window opens.

Read the license agreement. Click on "Print" if you wish to print out the conditions. Then select "I accept the terms of the license agreement" and click on "Next >". - OR - If you click on "< Back", then you return to the previous window.




– Standard mode The preconfigured settings are used. You can only set that the Internet settings are adapted using one option.






4. The "Controller configuration" window is opened

Select "Industrial PC" and click on "Next >".



5. The "Additional Products" window is opened. Only select the "Service Mode Client" if you wish to install the Service Mode client required for remote access. Click on "Next >".

6. If you selected the "Standard mode" installation type, the "Reconfigurable parameters"

window opens. Here, you can activate the "Internet proxy configurations" option if you wish to change the Internet settings. Click on "Next >".



- OR - If you selected installation type "Expert mode", then the "Choose Destination Location" window is opened. The installation directory is displayed. If you wish to use another directory, then press on the "Change..." button and enter the required directory.

7. If you selected the installation type "Expert mode", then the "Reconfigurable parameters"

window is displayed. For the individual configuration options, please refer to Chapter Configuring user-specific parameters - expert mode (Page 149)



8. The "SINUMERIK Integrate URL configuration" window is opened. You define the URLs of SINUMERIK Integrate here.

In the following message window you are only requested to check the address settings. Confirm the note to check the Internet settings with "OK".



9. This opens the window "Internet Properties". The address is specified under the "General" tab, in order to create the start page tabs. Click on the "Connections" tab in order to setup the Internet connection, and configure the LAN settings Click on "OK".



10. After this, the message window "Detected internet connection settings" is opened and shows the actual settings. Click on "< Back" to modify the settings. Click on "Next >" to continue.





12. The "Generic Driver Support" window is opened. Additional devices can be integrated here. Select "OPC driver" and click on "Next >".





14. The "Data transfer backup area location" window is opened, and shows you the archive directory for the temporary data. Click on "Browse..." if you wish to create another directory. Click on "Next > to continue.

15. The window "Log directory location" opens and shows you the archive directory for the

log data. Click on "Browse..." if you wish to create another directory. Click on "Next > to continue.



16. The "Data transfer area and logging settings" window is opened. Here you define the data storage if the Internet connection develops a fault. Enter the maximum data size for the transfer data, and click on "Next".


You can select one of three different strategies for the download Click on "Next >".



18. The "Startup parameter configuration" window is opened. Select the start properties of the client. Click on "Next >".

19. The "Time master settings for the machine" window is opened. You can change the time

synchronization between PLC and HMI. Set a checkmark for "Use HMI as time master" to activate the time synchronization. Click on "Next >".

















client version.

2. The next steps are described in the following section: Installing SINUMERIK Integrate

client (IPC) (Page 173).













2. A confirmation prompt is displayed. Confirm this message with "Yes" if an additional application, e.g. AMM is installed, and you wish to uninstall this application.




Client setup Access MyBackup (AMB), Analyze MyCondition (AMC) 5.5 Workstation PC



5.5 Workstation PC

5.5.1 Client setup A client installation is not required on a workstation PC.


Please refer to the following chapter regarding which Internet Explorer is suitable for your PC: System preconditions (Page 18).

References Additional information regarding the functions of AMC and AMB is provided in the Function Manual SINUMERIK Integrate AMC, AMB.


Client setup Access MyMachine (AMM) 66.1 Overview

The applications Access MyMachine and Access MyMachine SMC are only supported for Windows on a PCU 50.

The application is not available for a control with SINUMERIK Operate on NCU.

Installation Refer to the following chapters regarding the installation:

● PCU 50 with SINUMERIK Operate: Installing AMM Service Mode via Microsoft software installation (MSI package) (Page 191)

● PCU 50 with HMI-Advanced: Configuring SINUMERIK Integrate client (Page 196)

Update If remote access software, e.g. WebEx or RANG is available on the control, then you can install the actual AMM application using an update.

For an update, the old version is automatically uninstalled and replaced by the current version.

See Chapter: Loading an update into the control (Page 234).


6.2.1 Installing AMM Service Mode via Microsoft software installation (MSI package) If you are operating a PCU 50 with the operating software "SINUMERIK Operate", then the installation is realized by installing Microsoft software (MSI package).

Procedure 1. Start the setup file "AccessMyMachineServiceModeSetup.msi" using a double click.

English is the default installation language.


Client setup Access MyMachine (AMM) 6.2 SINUMERIK Operate machines






4. Select the installation directory. Click on "Next >" to accept the directory suggested by setup. - OR - Click on "Change..." to change the installation directory.


Press "Install" to start the installation.







Note Windows installer log file

The option of displaying the log file when installing depends on the version of the MSI installer that is on your computer. The log file is only available from version 4.0 of the MSI installer.

To do this, click on the option box "Show the Windows Installer log".

This option is not available for older versions.

6.2.2 Uninstalling AMM Service Mode


Select the setup "Access MyMachine Service Mode" and click on "Remove".


Client setup Access MyMachine (AMM) 6.3 HMI-Advanced machine



6.3.1 Configuring SINUMERIK Integrate client If the SINUMERIK Integrate client has already been installed, then the system identifies the scope of the installation. When compared to a new installation, several installation steps are skipped.

The procedure is subsequently described if the SINUMERIK Integrate client setup was already installed with another application, e.g. AMC and you wish to add the Access MyMachine/Ethernet (AMM/E) application.

If you are installing for the first time, see Chapter: Installing SINUMERIK Integrate client (Page 134).


the installation directory on the computer. English is the installation language. The "Welcome" window is opened, and offers you the following options:




Select "Reconfigure" and click on "Next >".











– Select "Access MyMachine (without Service Mode Client)" if you are installing AMM without the Service Mode. - AND /OR -

– Select "Service Mode Client" to install the Service Mode Client necessary for remote access.

Click on "Next >".

4. You will then receive a prompt whether you wish to make changes to the existing client

installation.

– Activate "NO - Do not prepare SINUMERIK Integrate for Series start-up" if you want to keep the existing installation.

Click on "Next >" to start the installation.



-OR- Select "YES - Prepare SINUMERIK Integrate Client for Series start-up" if you wish to change the parameter settings. Click on "Next >" to confirm the selection.

5. You obtain a confirmation prompt as to whether you wish to delete the directories that

have been created. The directories are deleted if you confirm the prompt with "Yes". You must now configure the parameters to address your requirements. For the next steps, see step ⑥. If you confirm the prompt with "No", then the directories already installed are kept. The installation is started and the procedure is displayed on a progress bar.



6. The "Reconfigurable parameters" window is displayed. A precise description of the configuration options can be found in the Chapter Configuring user-specific parameters - expert mode (Page 149)


Define the URLs of SINUMERIK Integrate. For the address data, a distinction is made between a connection to the Siemens server or a connection to a local server within a company network. If, in the "Additional Products" window, the two "Access MyMachine (without Service Mode Client)" and "Service Mode Client" applications are selected, then you must enter the following URLs: Establish a connection to the Siemens server:

– Display home page: https://www.epsnetwork.com/services/HMI/

– Render service: https://render.epsnetwork.com/IERenderService/HandshakeService.asmx

– Web service: https://www.epsnetwork.com/Services/MHC/MHComm.asmx



Click on "Next >" to continue.

-OR - If, in the "Additional Products" window, only "Service Mode Client" is selected, then you must enter the URLs "IAC" and "MHComm": Establish a connection to the Siemens server:

– IAC: https://www.epsnetwork.com/services/HMI/

– IAC: MHComm: https://www.epsnetwork.com/Services/MHC/MHComm.asmx






Enter the Internet connection and confirm by clicking on the "OK" button.



10. After this, the message window "Detected internet connection settings" is opened and shows the actual settings. Click on "< Back" to correct the settings. Click on "Next >" to continue.










14. The "Data transfer area location" window is opened, and shows you the archive directory for the temporary data. Click on "Browse..." if you wish to create another directory. Click on "Next > to continue.


the log data. Click on "Browse..." if you wish to create another directory. Click on "Next > to continue.









19. The "Time master settings for the machine" window is opened. You can change the time

synchronization between PLC and HMI. Set a checkmark for "Use HMI as time master" to activate the time synchronization. Click on "Next >".









6.3.2 Uninstalling client setup You remove an existing client setup with the installed application using "setup.exe".



2. The "Welcome" window opens. In the "Welcome" window, select the "Remove" function to remove the client setup with the installed applications. Click on "Next >".


Confirm the message with "OK" to start uninstallation.



4. You obtain an additional confirmation prompt as to whether you wish to uninstall the Service Mode Client. Click on "Yes" to start this operation.



Client setup Access MyMachine (AMM) 6.4 Machine PC


6.4 Machine PC

6.4.1 Configuring SINUMERIK Integrate Client (IPC) If the SINUMERIK Integrate client has already been installed, then the system identifies the scope of the installation. When compared to a new installation, several installation steps are skipped.

The procedure is subsequently described if the SINUMERIK Integrate client setup was already installed with another application, e.g. AMC and you wish to add the Access MyMachine (AMM) application.

If you are installing for the first time, see Chapter: Installing SINUMERIK Integrate client (IPC) (Page 173).


the installation directory on the computer. English is the installation language. The "Welcome" window is opened, and offers you the following options:




Select "Reconfigure" and click on "Next >".











Select "Service Mode Client" to install the Service Mode Client necessary for remote access.

Click on "Next >".

4. You will then receive a prompt whether you wish to make changes to the existing client

installation.

– Activate "NO - Do not prepare SINUMERIK Integrate for Series start-up" if you want to keep the existing installation.

Click on "Next >" to start the installation.



-OR- Select "YES - Prepare SINUMERIK Integrate Client for Series start-up" if you wish to change the parameter settings. Click on "Next >" to confirm the selection.

5. You obtain a confirmation prompt as to whether you wish to delete the directories that

have been created. The directories are deleted if you confirm the prompt with "Yes". You must now configure the parameters to address your requirements. For the next steps, see step ⑥. If you confirm the prompt with "No", then the directories already installed are kept. The installation is started and the procedure is displayed on a progress bar.



6. The "Reconfigurable parameters" window is displayed. A precise description of the configuration options can be found in the Chapter: Configuring user-specific parameters - expert mode (Page 149).


You define the URLs of SINUMERIK Integrate here. Enter the following URLs "IAC" and "MHComm" depending on your server. Establish a connection to the Siemens server: IAC: https://www.epsnetwork.com/services/HMI/ IAC: MHComm: https://www.epsnetwork.com/Services/MHC/MHComm.asmx Establish a connection to the local server: IAC: http://<servername or ip>/mcis_if/HMI MHComm: http://<servername or ip>/mcis_if/MHComm/MHComm.asmx Click on "Next >" to continue.





Enter the Internet connection. Use the connection in your company network that has already been set up and click on "OK".



10. After this, the message window "Detected internet connection settings" is opened and shows the actual settings. Click on "< Back" to correct the settings. Click on "Next >" to continue.










14. The "Data transfer backup area location" window is opened, and shows you the archive directory for the temporary data. Click on "Browse..." if you wish to create another directory. Click on "Next > to continue.

15. The window "Log directory location" opens and shows you the archive directory for the

log data. Click on "Browse..." if you wish to create another directory. Click on "Next > to continue.










You can change the time synchronization between PLC and HMI. Set a checkmark for "Use HMI as time master" to activate the time synchronization. Click on "Next >".







Client setup Access MyMachine (AMM) 6.5 Workstation PC


6.5 Workstation PC

6.5.1 Installing client setup Service Engineer ActiveX Client The client setup "Service Engineer ActiveX Client" is also required for a remote access.

You have the following option of starting the client setup:

● Via online download - OR -

● Via a download saved on a storage medium/hard disk.

Precondition Internet Explorer is installed on the workstation PC.

Please refer to the following chapter regarding which Internet Explorer is suitable for your PC: System preconditions (Page 18).

Online download The system checks whether the necessary software has been installed when you start the "Execute remote access" function.

If the Service Engineer ActiveX Client has still not been installed, then the "Version update" message window is displayed.



1. Follow the instructions and click on "OK" to start the installation.

2. The "FileDownload - Security Warning" window is opened. English is the user interface

language. You obtain the following data regarding setup:

– Name: Name of the setup

– Type: Type and size of the setup

– From: Specification of the Siemens server

Click on "Run" to start the download. Click on "Save" to save the setup and to initiate the installation at a later point in time.



3. After the download has been started, you obtain a progress display indicating the status, Click on "Run" to start the installation.

Refer to the section "Run setup" for the next steps.

Download from storage medium/hard disk You start the file download from the local copy in the installation directory on the computer or another storage medium.

The "File Download - Security Warning" window is opened. English is the user interface language. You obtain the following data regarding setup:

● Name: Name of the setup

● Type: Type and size of the setup

● From: Specification of the server

Click the "Run" button to start the download.

Refer to the "Run setup" for the next steps.



Running setup 1. If the following components have already been installed on the target system, then the

welcome screen is displayed, see step ④. If this is not the case, then the "InstallShield Wizard" window is displayed, and you obtain a list of the following components that are required:

– Microsoft F-Sharp Runtime 2.0

– Microsoft .NET Framework 4.0 client

Click on "Install" to start the installation.

2. The installation of "Microsoft F-Sharp Runtime 2.0" is started and the operation is

displayed using a progress display.



3. The installation of "Microsoft NET Framework 4.0 Client" is then started and the operation is displayed using a progress display.

4. The welcome screen is opened.

Click on "Next >" to start the installation preparation.



5. The "Destination Folder" window is opened. An installation directory is displayed as default.

– If you wish to change the installation directory, then press the "Change..." button and select another installation directory.

– Select for which users the installation should be made: Anyone who uses this computer (all users): The installation is carried out for all users. - OR - Only for me (User1): The installation is only carried out for the users currently logged on.

Click on "Next >" to accept the settings.


Press "Install" to start installation.





Client setup Access MyMachine (AMM) 6.6 Installing updates


Remote STEP 7 Remote STEP 7 is only available with SINUMERIK Operate on Linux systems.

When using Remote STEP 7, with the setup of Service Engineer ActiveX Client, the following files are automatically copied to your computer:

Windows XP: %WINDIR%\system32\remote_step7.dl

Windows 7: %CommonProgramFiles%\Siemens\Automation\Simatic OAM\bin\remote_step7.dll.

If the Service Engineer ActiveX Client is installed on the PC, where there is still no SIMATIC STEP 7, then the setup must be repeated if SIMATIC STEP 7 is subsequently installed.

6.6 Installing updates

6.6.1 Update V3.0 with WebEx/RANG V01

Introduction In order to be able to also use the Access MyMachine application on older Powerline controls, the following client version updates are available:

● Remote access with WebEx

● Remote access with RANG V1

The update uninstalls the 'Remote-access "WebEx" or "RANG V01", and installs the Access MyMachine (AMM) application.

Precondition Client version from V3.0 < V4.7.x with WebEx

Client version from V3.0 with RANG V1



Procedure 1. Navigate in the following directory on the installation CD: CD/RANG/plsl_client/RANGpl

and start "Setup_4.7.0.x.exe". English is the installation language. The welcome screen is opened. Click on "Next >".





3. The "SINUMERIK Integrate URL configuration" window is opened. Define the URLs of SINUMERIK Integrate. If, in the "Additional Products" window, the two "Access MyMachine (without Service Mode Client)" and "Service Mode Client" applications are selected, then you must enter the following URLs:

– Display home page

– Render service

– Web service


4. The "Ready to Install the Program" window is opened.

Click on "Install" to start the update.



5. The process is displayed using a progress bar.

6. The "InstallShield Wizard Complete" window is displayed and signals that the installation

was successfully completed. Click on "Finish" to complete the installation.



6.6.2 Loading an update into the control After completing the setup, update Access MyMachine (AMM) or Access MyMachine Service Mode (AMM SMC) from the user interface of HMI-Advanced.

If the current AMM Service Mode (SMC) has already been installed, then the "Update SMC" softkey is not displayed.

Updating teleservice The "Fault services" window is open. Press the "Update Teleservice" softkey to download the client setup AMM .

The installation is prepared, and is executed in the silent mode; i.e. you do not have to make any additional steps. The operation is displayed using a progress display.

During installation, you have the option of canceling the installation using the "Cancel" button.



Update SMC 1. The "Fault services" window is open.

Press the "Update SMC" softkey to download the client setup AMM Service Mode (SMC).

2. The installation is prepared, and is executed in the silent mode; i.e. you do not have to

make any additional steps. When the setup package has been unzipped, you obtain the following window:

3. Installation is displayed using a progress display.

During installation, you have the option of canceling the installation using the "Cancel" button.




Client setup Analyze MyPerformance (AMP) 77.1 Overview

Precondition The MMP server has been installed. You require the following access authorization to install and uninstall client setups: Protection level 1 (password: machine manufacturer).

Overview The client installation of Analyze MyPerformance (AMP) at the following workstations is described in the subsequent section:



● Workstation PC

References Take the configuration from the description "Configuration AMP".

You will find the description on the installation CD.








Client setup Analyze MyPerformance (AMP) 7.2 SINUMERIK Operate machines

























- OR -




Procedure





- OR -


stopped.




7.2.4 Installing the basis installation and AMP





3. Installing the AMP application (Page 246)



Procedure


1.




















Procedure


















7.2.4.3 Installing the AMP application



Columns Meaning Application name Installed application Actual version Current version number Reference version Checkmark Indicates that the actual version (effective version =

installed version) matches the reference version (nominal version).


Procedure

1. The "Settings" window is displayed and the activated applications are

shown. Press the "App-Installation" softkey.





The "Select file" window is opened and the directory overview is displayed.

4. If the data are, for example, on a USB flash drive, navigate in the "USB"

directory. Position the cursor on the "Analyze_MyPerformance_xx_xx_xx_xx.tar.gz" file and press the "OK" softkey.

5. You obtain a confirmation prompt that you must confirm with the "OK"

softkey.

The installation is started and the procedure is displayed on a progress bar.




application is shown under "Application is installed". Press the "OK" softkey.







7.2.5 Uninstalling the basis installation and AMP


1. Uninstalling the AMP application (Page 249)



7.2.5.1 Uninstalling the AMP application

Procedure

1.

The "App-Installation" window is opened. Select the "Analyze MyPerformance" application and press the "Uninstall" softkey.

2. The following confirmation prompt is displayed: "Do you really wish to uninstall this application: Analyze MyPerformancels". Press the "OK" softkey to remove the package. The process is displayed in a progress bar.

- OR -








Procedure



2.



- OR -



Client setup Analyze MyPerformance (AMP) 7.3 HMI-Advanced machines



Procedure



2.



- OR -



7.3 HMI-Advanced machines

7.3.1 Installing SINUMERIK Integrate client The SINUMERIK Integrate client contains the setup of the Analyze MyPerformance (AMP), Analyze MyCondition (AMC) and Access MyMachine (AMM) applications.

If the SINUMERIK Integrate client has already been installed, then the system identifies the scope of the installation. When compared to a new installation, several installation steps are skipped, see Chapter: Configuring SINUMERIK Integrate client (Page 196).

The procedure when installing for the first time is explained below.
















4. The "Controller configuration" window is opened Select "SINUMERIK" and click on "Next >".

5. The SINUMERIK connection types are displayed in the "Controller configuration" window.

If you are working in a networked environment, select "HMI-Advanced and SINUMERIK 840D/Di or 810D + PCU50/70". - OR - If separately integrated, e.g. via HMI Pro, then select "SINUMERIK with own integration".



6. Select the connection type in the next window:

– "1:1" The function allows a direct connection to the machine to be established.

– "1:N" The function allows a connection in a group with several machines.

– "Flying HMI": The function allows the use of SINUMERIK Integrate at machines, on which a client cannot be installed, because the operating software of the machine does not support this client. In this case, SINUMERIK Integrate is installed and configured on a workstation PC or machine PC (IPC). PC/IPC and machine communicate via a (W)LAN connection.

Select connection type 1:1 and then click on "Next >".



7. The "Additional Products" window is opened. Select these options only if you wish to install the Access MyMachine (AMM) application, see Chapter: Configuring SINUMERIK Integrate client (Page 196). Click on "Next >".

8. If you have selected the "Standard mode" installation type, then the "Reconfigurable

parameters" window is opened. You can select the following configuration:

– "HMI Softkey to start the product on the machine": After selecting this function, you can define the softkey position on the user interface.

– "Internet proxy configurations": After selecting this function, you can enter the interface to the Internet.

Click on "Next >".



9. If you select the "HMI Softkey to start the product on the machine", then the "Available Hotkeys" window is opened. From the drop-down list, select the position of the softkey with which you wish to start the application on the user interface. Click on "Next >".

- OR - Under step ③, if you selected installation type "Expert mode", then the "Choose Destination Location" window is opened. The installation directory is displayed. If you wish to use another directory, then press on the "Change..." button and enter the required directory.



10. If you selected the installation type "Expert mode", then the "Reconfigurable parameters" window is displayed. For the individual configuration options, please refer to Chapter: Configuring user-specific parameters - expert mode (Page 149).


Here, you define URLs of SINUMERIK Integrate only if you install Access MyMachine (AMM), see Chapter: Configuring SINUMERIK Integrate client (Page 196).





The address is specified under the "General" tab, in order to create the start page tabs. Click on the "Connections" tab in order to set up the Internet connection, and configure the LAN settings, see Chapter: Configuring Internet access (Page 153). Use the connection in your company network that has already been set up. Click on "OK".



14. After this, the message window "Detected internet connection settings" is opened and shows the actual settings. Click on "< Back" to correct the settings. Click on "Next >", to continue.





16. The "Generic Driver Support" window is opened. Additional devices can be linked in here, see Chapter: Selecting a driver (Page 155). Select "OPC driver" and click on "Next >".





18. The "Data transfer backup area location" window is opened, and shows you the archive directory for the temporary data, see Chapter: Changing the target directory data buffering (Page 158). Click on "Browse..." if you wish to create another directory. Click on "Next > to continue.

19. The "Log directory location" window is opened, and shows you the archive directory for

the log data, see Chapter: Changing the log file target directory (Page 159). Click on "Browse..." if you wish to create another directory. Click on "Next > to continue.



20. The "Data transfer area and logging settings" window is opened. Here you define where data is saved if an Internet connection develops a fault, see Chapter: Changing data volumes and protocol settings (Page 156). Enter the maximum data size for the transfer data, and click on "Next".


You can select one of three different strategies for the download, see Chapter: Changing the download method for the boot script (Page 161). Click on "Next >".



22. The "Startup parameter configuration" window is opened. Select the start properties of the client, see Chapter: Changing the start parameter client (Page 162). Click on "Next >".


Here you can change the time synchronization/alignment between the PLC and HMI, see Chapter: Changing the time synchronization between PLC and HMI (Page 164). Set a checkmark for "Use HMI as time master" if you wish to activate the time synchronization. Click on "Next >".









7.3.2 Stopping/starting SINUMERIK Integrate applications

Procedure 1. HMI-Advanced is started.

2. Press the "SINUMERIK Integrate" softkey.

3. The following window is opened.



4. If you press the <SELECT> key, then you obtain information as to which applications are available.

5. Press the "Client Diagnosis" softkey to display the settings.



6. Press the "Client Settings" softkey. If a checkmark is set in the check box "Services activated", then the application is active.

– Use of the applications is inhibited if you press the "Stop Services" softkey. You obtain a confirmation prompt that you must confirm with "OK". - OR - Press the "Cancel" softkey to cancel the process.

7. In order to reactivate applications, set a checkmark for "Services activated" and press the

"Start Services" softkey.

8. You obtain a confirmation prompt, that you confirm with "OK". - OR - Press the"Abort", softkey to interrupt the operation.











client version.

2. The next steps are described in the following section: Installing SINUMERIK Integrate

client (Page 252).












Confirm this message with "Yes" if an additional application, e.g. AMM is installed, and you wish to uninstall this application.







Client setup Analyze MyPerformance (AMP) 7.4 Workstation PC


7.4 Workstation PC

7.4.1 Opening the PC client via Internet Explorer There is a description on the installation CD that describes how you install and configure the PC client for AMP.

References "AMP configuration"

7.5 Variable logic

7.5.1 Introduction

Overview In the SINUMERIK Integrate environment, logical operations of control variables can be individually configured and without making any changes to standard products. This application area is addressed using the "Variable logic" application.

The "Configurator variable logic" application provides a graphic user interface for configuring logic strings as input for the "Variable logic" application.

"MCIS variable logic" is designated as "MCIS-VL" or briefly "VL" in the subsequent text.

Note References

Additional information about "MCIS variable logic" can be taken from the user documentation MCIS-Variablenlogik_V01.10.07.00.pdf.

Use Typical applications for MCIS-VL include:

● Forming the operating states to supply Analyze MyPerformance.

Here, based on control variables, e.g. production, standstill and fault states are formed. The interlocking logic required for this can be specifically created for each state.

● Determining maintenance intervals for MCIS TPM.

Client setup Analyze MyPerformance (AMP) 7.5 Variable logic


● Acquiring machine events for Manage MyTools Statistic.

● The use of MCIS-VL in conjunction with MCIS Base allows the amount of data transferred to the master computer to be reduced.

Area of validity The "Configurator variable logic" application is valid for the software component "MCIS variable logic", version 01.10.07.00.

7.5.1.1 Defining the logic using a text editor

Overview Up until now, the logic was formulated using a text editor (e.g. Notepad). In this case, the VL is saved in the form of an MCIS-C file (extension, MCC).

See example:

Figure 7-1 Example, defining logic using a text editor



7.5.1.2 Defining the logic using the application

Overview Using the "Logic configurator" application, it is possible to create the logic of the VL using a graphic user interface, and writing this to an MCIS-C file (extension MCC).

See example:

Figure 7-2 Example, defining logic using the application



7.5.1.3 Processing the MCIS-C file

Sequence For diagnostic purposes, the compiler creates an assembly listing (extension MCA) of the MCX file.

The MCX file is transferred to the control. There, it is interpreted by the runtime system of the variable logic (MCISVM.EXE). Optionally, several properties of the configured MCX file can be directly influenced on the runtime system. For this purpose, an optionally available INI file is evaluated on the runtime system.

The SLCAP or NCDDE server is responsible for the communication between NC and PLC.



7.5.2 Project processing

7.5.2.1 User interface

Overview

① Menu bar ② Property window Here, the properties of the logic element currently selected in the tree can be

processed. ③ Information and error

window Information about the currently displayed logic is displayed in the information window. Configuration errors are output in the error window, which were identified while generating code and which prevent code from being successfully generated. You can double-click on any entry in the error list. The logic element, which caused the error, is displayed.

④ Logic tree Graphic display of the logic string. Elements can be inserted either via the shortcut menu (right mouse key at an unconnected input) or using the element menu bar (5)). Elements can only be deleted using the shortcut menu.

⑤ Logic elements

Figure 7-3 Overview, variable logic configurator



7.5.2.2 Menu elements

Menu commands Menu command

Description

New Project In the menu bar, select "File" → "New Project". A new, empty project is created, and in this, creates a logic string.

Open Project In the menu bar, select "File" → "Open Project". An existing logic project (XML file) is opened.

Save In the menu bar, select "File" → "Save". The existing logic project with all logic strings and the project settings is saved as XML file.

Save as In the menu bar, select "File" → "Save as". A new logic project with all logic strings and the project settings is saved as XML file.

Close Project In the menu bar, select "File" → "Close Project". An open logic project is closed.

Add Logic In the menu bar, select "File" → "Add Logic". A new logic string is added with the open logic project.

Remove Logic

In the menu bar, select "File" → "Remove Logic". The currently selected logic string is removed from the logic project.

Project Settings

In the menu bar, select "Edit" → "Project Settings". The window to edit project settings is opened.

Generate Code

In the menu bar, select "Tools" → "Generate Code". The configuration is first validated and then the project code is generated. The syntax comprises variable logic and is saved as MCC file.

Note Validation

If one or several logic elements have errors, a message is output and code generation is canceled.



7.5.2.3 Project settings

Overview The following settings can be made:

"Code Generator" tab Code Template to use Programming language in which the code should be

generated. Currently, only variable logic in C++ is possible. Code Generator Output Path Location where MCC files should be saved. This setting is

optional. User-specific settings are possible.

Figure 7-4 Code generator settings

"Datasources" tab Several data sources, with alias names can be created in the list. Generally, only one data source is required.

Figure 7-5 Settings for the data sources



7.5.3 Logic elements

7.5.3.1 Inputs

Variable input

Datasource Name of the selected data source in "Project Settings" → "Data source".

DataType Data type of the input variables. StringDictionary A key value dictionary, which defines the conversion of strings into

numerical values. The comparison of the input with the strings in the dictionary is realized independent of uppercase and lowercase letters. If the dictionary has no entries, then the function is deactivated.

Format: <string1> = <number1>; <string2> = <number2> [...]; StringsOnly Number of inputs: A function generator has precisely one input. False: Initially, the input attempts to convert the value

numerically and then carries out a search in the dictionary. If the input is successfully converted into a numerical value, and this is also found in the dictionary, then the value is output from the dictionary.

True: The input only searches in the dictionary. Numerical input values, which are not included in the dictionary as key, are ignored.

Constant input

Datasource Name of the selected data source in "Project Settings" → "Data source". Optional for this element.

DataType Data type of the constants. Value Value of the constants.



7.5.3.2 Logic elements

AND

Datasource Name of the selected data source in "Project Settings" → "Data source". Optional for this element, and is only required if WriteAccess = true.

DataType Data type of the result of the logical operation. Is defined as INT. FunctionName Function name. NumInputs Number of inputs that must be logically combined. The number of

inputs is not restricted, however, there must be a minimum of two inputs.

OR


DataType Data type of the result of the logical operation. Is defined as INT. FunctionName Function name. NumInputs Number of inputs that must be logically combined. The number of

inputs is not restricted, however, there must be a minimum of two inputs.

NOT


DataType Data type of the result of the logical operation. Is defined as INT. FunctionName Function name. NumInputs Number of inputs. There is precisely only one input for a NOT

element.



7.5.3.3 Mathematical elements

ADD


DataType Data type of the result of the addition. Is obtained from the data types or both operands. For different operator data types, the result of the higher order data type is used.

FunctionName Function name. NumInputs Number of inputs. A mathematical element has precisely two inputs.

SUBTRACT


DataType Data type of the result of the subtraction. Is obtained from the data types or both operands. For different operator data types, the result of the higher order data type is used.


MULTIPLY


DataType Data type of the result of the multiplication. Is obtained from the data types or both operands. For different operator data types, the result of the higher order data type is used.




DIVIDE


DataType Data type of the result of the division. Is obtained from the data types or both operands. For different operator data types, the result of the higher order data type is used.


7.5.3.4 Comparison elements

EQUALS NOT


DataType Data type of the result of the comparison operation. Is defined as INT.FunctionName Function name. NumInputs Number of inputs. A comparison element has precisely two inputs.

EQUALS





EQUALS GREATER



EQUALS LESS



GREATER



LESS


DataType Data type of the result of the comparison operation. Is defined as INT.



FunctionName Function name. NumInputs Number of inputs. A comparison element has precisely two inputs.

7.5.3.5 Complex elements

WATCHDOG TIMER


DataType Data type of the output variables. Can be configured as required. FunctionName Function name. NumInputs Number of inputs. A watchdog timer has precisely one input. BayValue Value that is output when the timer is triggered. SilentValue Value that is output in the quiescent state of the timer. Time Time in milliseconds. BayValue is output, if, within this time, the value

at the input does not change. SilentValue is output if the value subsequently changes again.

DELIMITER


DataType Data type of the output variables. Has the same data type as the input variables.

FunctionName Function name. NumInputs Number of inputs. A delimiter has precisely one input. MaxValue The upper limit of the range in which the input value must lie. MinValue The lower limit of the range in which the input value must lie.



FUNCTION GENERATOR


DataType The data type of the output variable is defined as INT, as a function generator can only output a value of 0 or 1.

FunctionName Function name. NumInputs Number of inputs: A function generator has precisely one input. DirectFlanks If this value is true, then a rising or falling edge at the input is

immediately transferred to the output. If this value is false, then the actual state at the output is kept, corresponding to the set time. The output only goes to zero after the set time has expired.

StrictMode If StrictMode is false, then every value > 0 is treated as 1. If StrictMode is true, then every input value must be precisely 1 so that the condition applies.

HighDuration Duration of the high state in milliseconds. LowDuration Duration of the low state in milliseconds.

TIMER


DataType Data type of the output variables. Corresponds to the data type of the input variables.

FunctionName Function name. NumInputs Number of inputs. A timer has precisely one input. Mode TM_Normal: The input value is delayed by the time that

has been set. TM_DirectFallingEdge: If the input value is less than the value

presently being output, then the input value is transferred without any delay. If the input value is greater than the value presently being output, then the input value is delayed by the set time.



TM_DirectRisingEdge: If the input value is greater than the value presently being output, then the input value is transferred without any delay. If the input value is less than the value presently being output, then the input value is delayed by the set time.

DelayTime Time in milliseconds by which the output is delayed.

TRIGGERED COUNTER


DataType Data type of the output variables. For a counter is defined as INT. FunctionName Function name. NumInputs Number of inputs. A triggered counter has precisely one input. StrictMode If StrictMode is false, then every value > 0 is treated as 1. If

StrictMode is true, then every input value must be precisely 1 so that the condition applies.

Increment The counter value is incremented by this value when the counter trigger is initiated.

OverrunEnabled Activates or deactivates the overflow when the value specified under OverrunValue is exceeded.

OverrunValue If the counter state exceeds the value set here, then it is reset to the value set for InitialValue. This value is ignored, if OverrunEnabled = false.

Output variable Every logic element generates an internal output variable. When required, the output variable of every logic element can be written back into the NCDDE or SLCAP server.

Every output variable has the following properties, which can be set in addition to the properties of the logic element:

Address Name in the NCDDE or SLCAP. Can be kept empty, if the variable is only

internally used. DebounceTime Debounce time in ms. If this value is defined, then the change of the

variable is only evaluated if the value remains unchanged over the specified time.



InitialValue String with the initial value of local variables, e.g. "3.14". When creating these variables in the NCDDE or SLCAP server, variables on the local server are pre-assigned this value. Default: = "0"

ReadAccess Defines the type in which the variable is read: Default = OnStartup

OnStartup The variable is read once when starting or after an NCK reset. The data source is not subsequently accessed, if this variable is addressed within the logic blocks. The variable is read once when starting for all of the remaining alternatives for this option.

OnRequest If this variable is addressed within the logic blocks, then the actual value is read from the data source (DDE request).

OnTimer The variable is cyclically read. The interval is specified with the "Update Interval" option. The value that was read last is used in the logic blocks.

OnTimerRequest The same as OnTimer, in addition, (the same as for OnRequest) the actual value of the variable is read, if this is addressed in a logic block.

OnChange The value of the variable is updated via a hotlink, in synchronism with the data source. The value last signaled – via Hotlink – is used in the logic blocks.

SimulatorValue The value of the variable can be freely defined. The complete logic string can be simulated during the design process. Changes to the input values are immediately logically combined. Measuring points are located between the individual elements, where intermediate results can be read.

UpdateInterval Interval in ms for cyclically reading a variable. WriteAccess true / false

For true, a changed value of the variable is written to the data source (DDE poke). Write access is only permitted to NCDDE or SLCAP variables locally on the server, which start with "MDA_" or "VL_".



7.5.3.6 Logic elements

Use All logic elements are subject to the following rule:

If a certain element cannot be inserted at a specific location, then the symbol is deactivated. All activated elements can be combined with one another.

Overview The following logic elements can be used in a logic string:

● Inputs

● Logic elements

● Mathematical elements

● Comparison elements

● Complex elements


Annex A AA.1 List of abbreviations Admin Administrator (user role) AMB Access MyBackup AMC Analyze MyCondition AMM Access MyMachine AMP Analyze MyPerformance AMT Access MyTool ID ASP Application service provider version CAM Computer-Aided Manufacturing CF Card CompactFlash Card: Memory card CNC Computerized Numerical Control: Computerized numerical control CoL Certificate of License COM Communication CU Control Unit CP Communication Processor CPU Central Processing Unit: central processing unit DB Data Block (PLC) Dbxy Data block (e.g. B 59) DHCP Dynamic Host Configuration Protocol: Dynamic assignment of an IP address and

other configuration parameters on a computer in a network DNC Direct Numeric Control DIR Directory: Directory h Hour HMI Human Machine Interface: SINUMERIK user interface HTTP Hypertext Transfer Protocol, Hypertext transfer protocol HTTPS HyperText Transfer Protocol Secure, Safe hypertext transfer protocol HW Hardware IAC InterActive Client IE Internet Explorer IH Maintenance IIS Microsoft Internet Information Service MCI Motion Control Interface MCIS Motion Control Information System MCIS MDA MCIS Machine Data Aquisition: Machine data management MCP Machine Control Panel: Machine control panel MD Machine data MLFB Machine-Readable Product Code

Annex A A.1 List of abbreviations


MHComm Machine Handler Communication MMP Manage MyPrograms MMT Manage MyTools MPI Multi Port Interface: Multiport Interface MS Microsoft MSDE Microsoft Data Engine MSI Microsoft Software Installation MSTT Machine control panel NC Numerical Control: Numerical control NCK Numerical Control Kernel: Numerical kernel with block preparation NCU Numerical Control Unit: NCK hardware unit OB Organization block in the PLC ODBC Open Database Connectivity OEM Original Equipment Manufacturer OLE Object Linking & Embedding OP Operation Panel: Operating device OPI Operation Panel Interface: Operator panel interface OPC OLE for Process Control PC Personal Computer PCMCIA Personal Computer Memory Card International Association (Memory card

standardization) PCU PC Unit: Computing unit PG Programming device PDA Production Data Acquisition: Production data acquisition PLC Programmable Logic Control: Programmable memory control PMT Parts Monitoring & Tracking: Part tracking PO POWER ON ProToolPro Configuration tool PWS Personal Web Server SAT Satellite SK Softkey SEC Service Engineer Client SEG Tool Setting Station SMC Service Mode Client SW Software TDI Tool Data Information TC Teamcenter TLCA Tool Library CA: Tool catalog data TLCU Tool Library Customer: Customer tool catalog data TLCUA Tool Library Customer Assemblies: Complete tools WCS Workpiece Coordinate System T Tool TLC Tool Length Compensation

Annex A A.1 List of abbreviations


WOP Workshop-Oriented Programming WPD WorkPiece Directory: Workpiece directory TRC Tool Radius Compensation T Tool TO Tool Offset TM Tool Management TC Tool Change XML Extensible Markup Language

Annex A A.2 840D sl documentation overview


A.2 840D sl documentation overview


Index

A Access-it!

Applications, 12 AMM

Update, 234 AMM Service Mode

Uninstalling, 195 Uninstalling with HMI-Advanced, 210 Update, 235

AMP AMC, AMB Server installation, 61

Analyze-it! Applications, 12

B Base Setup, 244

Uninstalling, 251 Basis installation

Base Setup, 245 Installer, 241

C Client

Overview, 16 Configuring URL, 150

D Data transfer, 158 Download methods for the boot script, 161

E ePS names, 12 Expert mode, 149

F Firewall settings, 20

G Generic Driver Support, 155

I IAC.exe, 166 Installer, 242

install, 242 Uninstalling, 252

Installing AMM AMP AMC client with HMI-Advanced, 253

Installing AMM Service Mode PCU 50 with SINUMERIK Operate, 191

Installing SINUMERIK Integrate client At the machine PC, 211

Installing the AMP client with SINUMERIK Operate, 247

Installing the MMP client on the workstation PC, 118 with HMI-Advanced, 112 with SINUMERIK Operate, 107

Installing the MMT client at the workstation PC, 91 with HMI-Advanced, 84 with SINUMERIK Operate, 79

Installing the TRANSLINE client setup, 165

L Log file directory, 159

M Manage-it!

Applications, 12 MCIS names, 12 MhController, 167 MhCtrlr.exe, 167 MMP

Server installation, 54 Uninstalling the server, 60

MMT Server installation, 45 Uninstalling the server, 53

Index


MSI installer, 195

S Server

Overview, 15 Overview of the installations, 21

Server installation AMP AMC, AMB, 61 MMP, 54 MMT, 45

Service·Engineer·ActiveX°Client Download from the hard disk, 225 Online download, 223 Remote STEP 7, 230

Setting data volumes, 157 SINUMERIK Integrate

Applications, 14 Displaying the softkey, 238 enable at SINUMERIK Operate, 239 Overview of the modules, 11 Start properties, 163 stopping at SINUMERIK Operate, 240 Stopping/enabling at HMII-Advanced, 268

SINUMERIK Integrate client Change, 270 Remove, 272 Repair, 270

System requirement, 18

T Time synchronization, PLC-HMI, 164

U uninstalling the AMP client

with SINUMERIK Operate, 249 Uninstalling the MMP client

at the workstation PC, 122 with HMI-Advanced, 117 with SINUMERIK Operate, 108

Uninstalling the MMT client at the workstation PC, 96 with HMI-Advanced, 90 with SINUMERIK Operate, 80

Uninstalling the server MMP, 60 MMT, 53

Update Access MyMachine SMC, 235

Teleservice, 234

W Windows services

under Windows 2003, 32 bit, 22 Under Windows 2008R2, 30 Under Windows 7, 42

Documents

Installation Manual SINUMERIK Integrate MMT, MMP, AMB, … · MMT, MMP, AMB, AMC, AMM, AMP Installation Manual, 03/2013, 6FC5397-6EP40-0BA0 3 Preface SINUMERIK documentation The SINUMERIK