Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
STEP 1
STEP 1 Spread adhesive using a 1/2in (12.7mm) notch trowel.
STEP 2 A&B Lay tiles and insert appropriate Spacer using the Flat Spacer along the edge and the Cross Spacer (shown) in the intersection. Spacers are also available in Tees for brick bond projects.
STEP 3 After Spacers are installed, place Cap by sliding it through the Spacer firmly.
STEP 4 Slide the Evolver Tool onto the Spacer and pull trigger to apply tension between the Cap and tile until the Cap is firmly holding tile. The tension knob at rear of gun can be turned clockwise or counter clockwise to set the tension for the thickness of that tile.
LET TILES FULLY SET (Per Manufacturer’s Instructions)
STEP 5 WALLS To remove Caps and Spacers after tiles have fully set, wind adjuster knob counter clockwise on the Evolver Tool to adjust tension. Place Evolver Tool back on Spacer and pull trigger until Spacer breaks off to fully remove.
STEP 5 FLOORSFor floor installations, Spacers can be kicked (parallel to the spacer) to break off in order to save time. Once Spacer is broken off Caps can be removed with the Decapper Tool. On softer Natural Stones & Tiles use Evolver Tool only to remove Caps and Spacers.
STEP 6 Insert Decapper Tool and place tapered end (tip) between the Cap and strap to loosen tooth. Slide the center slot through the Spacer and hook under Cap. Push down with thumb while supporting the Cap with index finger and slide Cap upwards removing the Cap from the Spacer. Discard the Spacer and keep Cap for reuse. WALLS Always place Spacer in a vertical position (cross as shown in diagram) or horizontal position (tee or flat) to avoid chipping tiles when removing the following day.
A Complete Tile & Spacer Leveling System in One!
The Easiest & Quickest way to Level & Space Wall & Floor Tiles
Levolution is a complete Tile Spacing & Leveling system in One! With its removable Spacer it allows you to choose between 1⁄16-in, 1⁄8-in, and 3⁄16-in grout joints. It also comes in 3 different space profiles, including a Cross for general stack bond, a Tee for laying tiles in a brick pattern and also a Flat Spacer.
Other systems on the market require you to use up to 4 pieces per intersection and an additional piece every 12“ with large format tiles in order to keep them level. Levolution requires only one piece per intersection regardless of size which means your laying tiles instead of extra pieces. This results in more productivity saving you time.
levolution
STEP 2 - A
STEP 3
STEP 4 STEP 5 - WALLS
STEP 6
STEP 2 - B
WALLS
STEP 5 - FLOORS
LET
TILE
S F
ULL
Y S
ET
Visit www.miraclesealants.com to view product video
INSTALLATION:
On softer Natural Stones & Tiles use Evolver Tool
ONLY to remove Caps and Spacers.
levo
lutio
nA
revo
lutio
n in
tile
spac
ing
and
leve
ling!
Miracle Sealants Company12318 Lower Azusa RoadArcadia, California 91006-5872
Technical Support• Product Information• Product Use• Warranty [email protected] 800 350-1901 ext. 1
Customer Service• Order Tracking• Damaged Product• Changes on Existing Orders • Warranty [email protected] ext. 2
Marketing Department• Sales Tools, Literature & Samples• Sales Promotions & Events• Customer [email protected] ext. 3
Order ProcessingFax – (626) 443-1435 (Download Fax Forms)Online Order Forms (Distributors Only)[email protected]
Monday – Friday 8:30am – 5:00pm PST
LEV
_BRO
_16
Visit www.miraclesealants.com to view product video
CONTACT
4
LEVOLUTION
AVERAGE = Up to 4 PER SQUARE FOOT
When calculating pieces per square foot you have to take an average as shown in diagram above. However there is always a
finishing point and a starting point (walls).
Wall
Wall
FLAT SPACER CROSS SPACER TEE SPACER
Spacer Size: 1/16in (1.5875mm) - Green
Spacer Size: 1/8in (3.175mm) - Yellow
FLAT SPACER CROSS SPACER TEE SPACER
FLAT SPACER: Are used at Wall Edges
CROSS SPACERS: Are used in the intersections
TEE SPACERS: Are used for brick bond projects
SYSTEM COMPARISON
CAP
SYSTEM COMPONENTS
DECAPPER TOOL
EVOLVER TOOL
Universal Caps that can be reused
A tool that removes the used Spacers from the Caps so the Caps may be reused.
A Tensioning Tool with adjustable knob.Tensioning dial for accurate clamping.
Comfortable ergonomic handle & trigger.
FLAT SPACER CROSS SPACER TEE SPACER
Spacer Size: 3/16in (4.7625mm) - WhiteREPLACEMENT TEETH
Evolver Tool Replacement Teeth
COMPETITIVE SYSTEMS
AVERAGE = 1 PER TILE(Regardless of Size)
MSC
_com
m_0
2_20
16
AVERAGE = 1 PER TILE (Regardless of Size)
COMPETATIVE SYSTEMS
AVERAGE = Up to 4 PER SQUARE FOOT
When calculating pieces per square foot you have to take anaverage as shown in diagram above. However there is always a
finishing point and a starting point (walls).
Wall
Wall
Levolution Brochureps2 3/31/16 9:12 PM Page 5
MSC
_com
m_0
2_20
16
AVERAGE = 1 PER TILE (Regardless of Size)
COMPETATIVE SYSTEMS
AVERAGE = Up to 4 PER SQUARE FOOT
When calculating pieces per square foot you have to take anaverage as shown in diagram above. However there is always a
finishing point and a starting point (walls).
Wall
Wall
Levolution Brochureps2 3/31/16 9:12 PM Page 5