INSTALLATION INSTRUCTIONS

®

PROXIMTY SYSTEMS © DOCUMENT v1.0 2017

Rear View

POWERDRILL

DRILLBIT

PHILLIPSSCREW DRIVER PENCIL SAFETY

GLASSESTAPE

MEASURE LEVEL

"Z" CLIPSMOUNTING RAILS

WALLANCHORS

ITEMS REQUIRED FOR CABINET INSTALLATIONNOT INCLUDED

INSTALLATIONSCREWS

ITEMSINCLUDED

Rear View

ElectricalCut-Out

Finished Install View

page 1

MD ARMTRACK

ULTRA ARM

CPUWIREFRAME

LIN

E O

F PR

OXI

MIT

YC

ABIN

ET

WALLS MAY VARY FROM SITE LOCATION

FINISHED FLOOR

TOP OF KEYBOARD TRAY

INSTALLATIONSTEP 1LOCATE THE AREA WHERE THE CABINET WILLBE INSTALLED. SEE FIGURE 1

STEP 2DETERMINE YOUR WORK SURFACE DESIREDHEIGHT FOLLOWING THE MEASUREMENTS ASSEE FIGURE 1.

FIGURE 1

CENTER LINE OFWALL STUDS

TYPICALSTUD SPACING

CABINET. SEE FIGURE 2

DRILL SCREW INTOSTUD TO SECURE

CABINET. SEE FIGURE 2

WARNING:INSTALLATION GUIDELINES ARE BASED UPON THE MOST COMMON INSTALLATIONS & AREPROVIDED AS A REFERENCE ONLY. HOWEVER, BECAUSE SURFACES MATERIALS & WALLSTRUCTURES ARE WIDELY VARIED, IT IS THE CUSTOMERS RESPONSIBILITYTO CONSULT WITH APPROPRIATE ENGINEERING, ARCHITECTURAL OR CONSTRUCTIONPROFESSIONAL TO ENSURE THAT THE PROXIMITY UNIT IS MOUNTED PROPERLY TOHANDLE APPLIED LOADS.

CHECK FOR UTILITIES IN WALL CAVITY BEFORE INSTALLING WORKSTATION. (PLUMBING,ELECTRICAL, ETC)

FROM BOTTOM EDGE TOLEVEL POSITION OFTRAY SURFACE FOR KEYBOARD = 6.8”.

6.8

DRILL SCREW INTOSTUD TO SECURE

CABINET. SEE FIGURE 2

DRILL SCREW INTOSTUD TO SECURE

CABINET. SEE FIGURE 2

31” is recommendedif the arm will be used at a seated height.Arm will be rotated to bo�om posi�on.

page 2

METAL / WOODSTUD

CABINET & WALLSECTION

TOP "Z" CLIP WALLMOUNT RAIL

BOTTOM "Z" CLIPWALL MOUNT RAIL

WALLANCHOR

"Z" CLIPWALL MOUNTRAIL

MOUNTING WALLMAY VARY

PROXIMITYCABINET

FIGURE 3

MOUNT RAIL

GYPSUMWALL

METAL / WOODSTUD

INSTALLATIONSCREW

"Z" CLIPWALL MOUNT RAIL

SECURE SCREWINTO METAL/WOOD

STUD

GYPSUMWALL

TYP SECTIONVIEW

FIGURE 2

STEP 3MARK "Z" CLIP MOUNTING LOCATION ATAPPROPRIATE LOCATIONS FOR DESIREDMOUNTING HEIGHT. USE LEVEL TO MAKE SURETHE "Z" CLIPS WILL BE MOUNTED STRAIGHT &MARK APPROPRIATE ANCHOR / SCREWLOCATIONS. SEE FIGURE 2.*

STEP 4INSTALL WALL ANCHORS ATMARKED LOCATIONS. SEE FIGURE 3.

STEP 5SCREW WALL ANCHORS INTO THE DRILLEDHOLES IN THE WALL. SEE FIGURE 3.

STEP 6PLACE THE "Z" CLIPS ON THE WALL & INSERTTHE WALL ANCHOR SCREWS INTO THE THE"Z" CLIP PRE-DRILLED HOLES & TIGHTENTO SECURE EACH "Z" CLIP TO MAKE STURDY.SEE FIGURE 3.

*UNITS SHOULD BE FASTENED TO WALL STUDS.STANDARD UNITS ARE 28" IN WIDTH. PROPERPOSITIONING SHOULD ALLOW FOR FASTENING TOTWO WALL STUDS IF WALL STUDS ARE 16" ON CENTER.BE SURE TO ALIGN THE ARM TRACK WITH A STUD AS WELL.

WALL BLOCKING MAY BE USED IN AREAS WHEREWALL STUDS ARE NOT AVAILABLE.

page 5

1 2 3 4op�ons

UL180

UL182

Holes on the back act as atemplate. Drill through to complete installa�on on

one of the posi�on op�ons.

These posi�ons will center the monitorwhen stowed.

Mount track toback board

(8X)

Mount Trackthrough to Studs

(8X)

Do not drill through other hole op�ons.They will be visible.

(see next page)

Rear of Unit

page 3

Arm will stow withelbow to right, to center monitorfor this posi�on.

Arm will stow withelbow to le�, to center monitorfor this posi�on.

page 4

BOTTOM CLIP WALLMOUNT RAIL TOBE ATTACHED TO WALL

BOTTOM REARPOCKET OF

CABINET

FIGURE 4a

FIGURE 4b

STEP 7POSITION CABINET IN FRONT OF MOUNTED "Z"CLIPS. SEE FIGURE 4a.

STEP 8LIFT CABINET SO THAT THE "Z" CLIPS &HANGRAIL BRACKETS ARE SLIGHTLY ABOVE THEIRCORRESPONDING MOUNTING SYSTEM ON THEPUSH THE CABINET FLUSH TO THE WALL &LET IT SLIDE DOWN SLOWLY UNTIL MOUNTINGSYSTEM CATCHES. ENSURE EACHCORRESPONDING PIECE OF HARDWARE ISMOUNTED & PULL CABINET DOWN AS REQUIREDTO SECURE THE HARDWARE PIECES TOGETHER.AFTER, DRIVE SCREWS THROUGH WALL TRACK TOSTUD.SEE FIGURE 4b.

Align the arm track with astud loca�on when placing.

Through to Wall Stud

page 6

STEP 9OPEN THE TOP COMPARTMENT DOOR. PUT ALEVEL ON THE TOP SHELF TO MAKE SURE THECABINET IS LEVELED. ALSO, PLACE LEVEL ONSIDE OF CABINET TO CHECK PLUMB.SEE FIGURE 5.

FOR ADDITIONAL SECURITY INSTALL SCREWSTOWARDS THE TOP CORNERS OF THE CABINET ONEACH SIDE. THE SCREW WILL PREVENT IT FROMLIFTING OFF THE "Z" CLIP RAILS.SEE FIGURE 6.**

FIGURE 5

FIGURE 6

FIGURE 6

ADJUSTABLEHANGRAILBRACKET

TOP "Z" CLIPWALL MOUNT RAIL

STEP 10

Security Screw

page 7

STEP 1PLACE COMPUTER UNIT ON THE TOP SHELF & USEWIRE SHAPES TO STABILIZE COMPUTER SECURELY.SEE FIGURE 1.

STEP 2SEVERAL HOLES EXIST TO PROVIDE POSITIONOPTIONS FOR THE COMPUTER. LEFT, RIGHT ORCENTER. SEE FIGURE 2.STEP 3OVERLAP THEM OR NOT FOR THE WIDTH &STORAGE NEEDS. SEE FIGURE 3.

FIGURE 1

COMPUTERSECURING

FIGURE 2

FIGURE 3

page 8

STEP 1OPEN THE TOP DOOR TO REVEAL THE (2) HINGESTHAT HOLD THE DOOR. SEE FIGURE 1.

STEP 2CLOSE THE DOOR & MAKE SURE THATTHE GAP IS EVEN ALL THE WAY AROUND. IF NOTEVEN, REPEAT AGAIN & MAKE MINOR ADJUSTMENTS.SEE FIGURE 2.

UPPER DOORADJUSTMENTS

FIGURE 1a

FIGURE 2

FIGURE 1b

GAP SHOULDBE EVEN ALL THE

WAY AROUNDSEE HINGE

ADJUSTMENT DETAIL

Raises and lowers the door

Moves doorin or out

Adjust Sideto Side

Making DoorAdjustments

page 9

ADJUSTS SIDETO SIDE IF

NECESSARY

MOUNTING TO MD TRACK

ICW

Socketcap screw

VESAplate

ICW RECOMMENDS WOOD OR METAL STUD MOUNTING ONLY.

W2 W3

USE A LEVEL TO BE SURE MOUNT IS CORREECTLY ALIGNED.

MOUNT WALL PLATE TO MD TRACK

STEP 1

STEP 2

STEP 3

STEP 4

STEP 2

STEP 3

STEP 4

Locate the Arm Box.

Remove the Arm, and all of its contents.

page 10

ATTACH FLIP UPRemove screws from drop extension using 5/32” hex key.Align holes in keyboard tray with screw holes in drop extension.

the provided screws.

S

page 11

end