Embed Size (px)
Citation preview
EDGE CHANDELIERSTUDIO H
Installation InstructionsINSTALLATION MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN
PLEASE USE THE FOLLOWING DIAGRAM AND STEPS FOR INSTALLATION
J-BOX & CEILINGCANOPY
MOUNTING PLATE
TEMPORARYCHAINS
LABELED CABLE& CORD HOLES
CANOPY w/ MOUNTED POWERSUPPLIES AND WIRES.
(FIXTURES VARY, NOT ALLARE SHOWN)
UPPER DIFFUSER
STRAIN RELIEF
LIGHT BAR
LOWER DIFFUSER
8-32 x 3/16" CONE POINT SET SCREW
ELEC. CORD
CABLEADJUSTERS
HOLLY HUNT LIGHTING___________________
NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS
COMPLETE.
SUSPENSION CABLES
NOTE: DO NOT OVERTIGHTEN SCREWS
CONTENTS
(1) Rectangular Canopy 36" L x 18" W
(1) Canopy Mouting Frame
(3) Light Bar, Electrical Cord and pre-installed Strain Relief with Set
Screw
(3) Lower Acrylic Diffuser
(3) Upper Acrylic Diffuser
(6) Suspension Cables, Labeled and pre-marked with insertion depth
(4) Canopy Mounting Screws (#10-32)
(4) Temporary Chains w/ S-Hooks
(3) Hex Wrench 1/16, 5/64, 1/8
(4) Sets of Gloves to be worn during installation.
UL Approved in US and Canada
HOLLY HUNT LIGHTING___________________
NOTE: DO NOT OVERTIGHTEN SCREWS
STUDIO HEDGE CHANDELIERInstallation Instructions
INSTALLATION MUST BE PERFORMED BY A QUALIFIED ELECTRICIANPLEASE USE THE FOLLOWING DIAGRAM AND STEPS FOR INSTALLATION
NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE.
INSTRUCTIONS1. Determine fixture location, J Box should be located on the center of the Fixture.2. Screw Canopy Mounting Plate to ceiling w/ appropriate screws and/or anchors per
installation requirements. (Mounting requirements and hardware to be determinedand provided by installer)
3. Hang Temporary Chains from Canopy Mounting Plate; raise Canopy to hang fromTemporary Chains, note alignment mark on Canopy Mounting Plate and Canopy. NOTE:TEMPORARY CHAINS ARE NOT MEANT TO BE LEFT SUSPENDING THE FIXTURE FOREXTENDED PERIODS OF TIME
4. Connect 110-277 Volt power to pre-wired fixture (black and white wires). All powersupplies have been installed by manufacturer. The drivers installed in this unit havemultiple methods of dimming to accommodate your needs. The systems are capableof Triac dimming at 120 VAC or have the option for 0-10 vdc current-sinking controlfor dimming.
5. Make Electrical connections to fixture based on dimming type or controls withprovided wiring diagrams supplied with dimming or control options. (See next page fordiagrams.) This fixture can be wired to accept Triac dimming or 0-10V dimming orswitch (the 0-10V dimming signal must be supplied to the purple and gray wires asthere is no reference voltage supplied from the driver for this dimming option)). If nodimming is required cap gray and purple wires from the driver and install a non-dimming switch wired per switch instructions.
6. Slide the labeled Suspension Cables into corresponding holes through top of Canopy.7. Match the Light Bars to their corresponding labels in the Canopy and hang all Light
Bars from the Suspension Cables with Cable Adjusters to the insertion depth markedon the Cables.
8. Loosen Set Screws pre-installed in Strain Reliefs with provided Hex Wrench.9. Uncoil silver cloth covered Elec. Cord and feed through Strain Reliefs. Snug the set
screw in the Strain Relief against the Cord when the Cord is hanging straight---DONOT OVERTIGHTEN.
10. Make electrical connections with Snap Connectors at labeled positions in Canopy.Connect to Supply Power with wire nuts and Ground to Canopy.
11. Remove pre-installed 8-32 x 3/16" Cone Point Set Screws from ends of Light Barsusing provided Hex Wrench. Reaise each numbered Lower Diffuser to thecorresponding Light Bar and secure into bottom slot by re-installing Cone Point SetScrews. DO NOT OVERTIGHTEN SCREWS.
12. Install Upper Diffusers into Light Bars.13. Remove Temporary Chains and raise the Canopy to the Canopy Mounting Plate.
Secure with provided 10-32 screws (start all screws before final tightening).14. Based on site conditions, a slight leveling of Light Bars may be necessary. Pressing
the center cylinder of the Cable Adjuster will release pressure on the Cable and LightBar can be repositioned.
___________________HOLLY HUNT LIGHTINGSTUDIO H
EDGE CHANDELIERInstallation Instructions
INSTALLATION MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN PLEASE USE THE FOLLOWING DIAGRAM AND STEPS FOR INSTALLATION
NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE.
Red
Blu
e
0-10V
Power Supply
Ref. Control ModuleDimmer
Switch
Purple
Gray
White
Black
Light Bar Below Light Bar Below
Black
WhitePower Supply
Gray
Purple
Black
White
Light Bar Below Light Bar Below
Power Supply Power Supply
Power SuppliesTo More
To MorePower Supplies
Black
White
Red
Blu
e
Purple
Gray
White
Black
Gray
Purple
Wire Nut
To 120/240V J-BoxInside of Canopy
Inside of Canopy
Black
White
Inside of Canopy
Power SuppliesTo More
White
BlackPower Supply
White
BlackPower Supply
Blu
e
Red Blu
e
Red
Gra
y
Purp
lePurple
Gray
Wire Nut
Light Bar Below Light Bar Below
DimmerTriac
REFERENCE WIRING DIAGRAM FOR 0-10V DIMMING
REFERENCE WIRING DIAGRAM WITHOUT DIMMING
REFERENCE TRIAC WIRING DIAGRAM
HOLLY HUNT LIGHTING___________________HOLLY HUNT STUDIOEDGE CHANDELIERInstallation Instructions
INSTALLATION MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN PLEASE USE THE FOLLOWING DIAGRAM AND STEPS FOR INSTALLATION
NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE.
EDGE CHANDELIERSTUDIO H
Installation InstructionsINSTALLATION MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN
PLEASE USE THE FOLLOWING DIAGRAM AND STEPS FOR INSTALLATION
J-BOX & CEILINGCANOPY
MOUNTING PLATE
TEMPORARYCHAINS
LABELED CABLE& CORD HOLES
CANOPY w/ MOUNTED POWERSUPPLIES AND WIRES.
(FIXTURES VARY, NOT ALLARE SHOWN)
UPPER DIFFUSER
STRAIN RELIEF
LIGHT BAR
LOWER DIFFUSER
8-32 x 3/16" CONE POINT SET SCREW
ELEC. CORD
CABLEADJUSTERS
HOLLY HUNT LIGHTING___________________
NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS
COMPLETE.
SUSPENSION CABLES
NOTE: DO NOT OVERTIGHTEN SCREWS
CONTENTS(1) Rectangular Canopy 72" L x 18" W
(1) Canopy Mouting Frame
(5) Light Bar, Electrical Cord
(5) Strain Reliefs with Nylon Tip Set Screw Installed
(5) Lower Acrylic Diffuser
(5) Upper Acrylic Diffuser
(10) Suspension Cables, Labeled and pre-marked with insertion depth
(6) Canopy Mounting Screws (#10-32)
(4) Temporary Chains w/ S-Hooks
(3) Hex Wrench 1/8", 1/16" and 5/64"
(4) Sets of Gloves to be worn during installation.
(2) Extra Butt Connector
(2) 8-32 x 3/16 or 1/4 Cone Point SS, Pre-installed per Light Bar
(5) Blue Wire Nuts
UL Approved in US and Canada
HOLLY HUNT LIGHTING___________________
NOTE: DO NOT OVERTIGHTEN SCREWS
STUDIO HEDGE CHANDELIERInstallation Instructions
INSTALLATION MUST BE PERFORMED BY A QUALIFIED ELECTRICIANPLEASE USE THE FOLLOWING DIAGRAM AND STEPS FOR INSTALLATION
NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE.
INSTRUCTIONS1. Determine fixture location, J Box should be located on the center of the Fixture.2. Screw Canopy Mounting Plate to ceiling w/ appropriate screws and/or anchors per
installation requirements. (Mounting requirements and hardware to be determinedand provided by installer)
3. Hang Temporary Chains from Canopy Mounting Plate; raise Canopy to hang fromTemporary Chains, note alignment mark on Canopy Mounting Plate and Canopy. NOTE:TEMPORARY CHAINS ARE NOT MEANT TO BE LEFT SUSPENDING THE FIXTURE FOREXTENDED PERIODS OF TIME
4. Connect 110-277 Volt power to pre-wired fixture (black and white wires). All powersupplies have been installed by manufacturer. The drivers installed in this unit havemultiple methods of dimming to accommodate your needs. The systems are capableof Triac dimming at 120 VAC or have the option for 0-10 vdc current-sinking controlfor dimming.
5. Make Electrical connections to fixture based on dimming type or controls withprovided wiring diagrams supplied with dimming or control options. (See next page fordiagrams.) This fixture can be wired to accept Triac dimming or 0-10V dimming orswitch (the 0-10V dimming signal must be supplied to the purple and gray wires asthere is no reference voltage supplied from the driver for this dimming option)). If nodimming is required cap gray and purple wires from the driver and install a non-dimming switch wired per switch instructions.
6. Slide the labeled Suspension Cables into corresponding holes through top of Canopy.7. Match the Light Bars to their corresponding labels in the Canopy and hang all Light
Bars from the Suspension Cables with Cable Adjusters to the insertion depth markedon the Cables.
8. Loosen Set Screws pre-installed in Strain Reliefs with provided Hex Wrench.9. Uncoil silver cloth covered Elec. Cord and feed through Strain Reliefs. Snug the set
screw in the Strain Relief against the Cord when the Cord is hanging straight---DONOT OVERTIGHTEN.
10. Make electrical connections with Snap Connectors at labeled positions in Canopy.Connect to Supply Power with wire nuts and Ground to Canopy.
11. Remove pre-installed 8-32 x 3/16" Cone Point Set Screws from ends of Light Barsusing provided Hex Wrench. Reaise each numbered Lower Diffuser to thecorresponding Light Bar and secure into bottom slot by re-installing Cone Point SetScrews. DO NOT OVERTIGHTEN SCREWS.
12. Install Upper Diffusers into Light Bars.13. Remove Temporary Chains and raise the Canopy to the Canopy Mounting Plate.
Secure with provided 10-32 screws (start all screws before final tightening).14. Based on site conditions, a slight leveling of Light Bars may be necessary. Pressing
the center cylinder of the Cable Adjuster will release pressure on the Cable and LightBar can be repositioned.
___________________HOLLY HUNT LIGHTINGSTUDIO H
EDGE CHANDELIERInstallation Instructions
INSTALLATION MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN PLEASE USE THE FOLLOWING DIAGRAM AND STEPS FOR INSTALLATION
NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE.
Red
Blu
e
0-10V
Power Supply
Ref. Control ModuleDimmer
Switch
Purple
Gray
White
Black
Light Bar Below Light Bar Below
Black
WhitePower Supply
Gray
Purple
Black
White
Light Bar Below Light Bar Below
Power Supply Power Supply
Power SuppliesTo More
To MorePower Supplies
Black
White
Red
Blu
e
Purple
Gray
White
Black
Gray
Purple
Wire Nut
To 120/240V J-BoxInside of Canopy
Inside of Canopy
Black
White
Inside of Canopy
Power SuppliesTo More
White
BlackPower Supply
White
BlackPower Supply
Blu
e
Red Blu
e
Red
Gra
y
Purp
lePurple
Gray
Wire Nut
Light Bar Below Light Bar Below
DimmerTriac
REFERENCE WIRING DIAGRAM FOR 0-10V DIMMING
REFERENCE WIRING DIAGRAM WITHOUT DIMMING
REFERENCE TRIAC WIRING DIAGRAM
HOLLY HUNT LIGHTING___________________HOLLY HUNT STUDIOEDGE CHANDELIERInstallation Instructions
INSTALLATION MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN PLEASE USE THE FOLLOWING DIAGRAM AND STEPS FOR INSTALLATION
NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE.
EDGE CHANDELIERSTUDIO H
Installation InstructionsINSTALLATION MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN
PLEASE USE THE FOLLOWING DIAGRAM AND STEPS FOR INSTALLATION
J-BOX & CEILINGCANOPY
MOUNTING PLATE
TEMPORARYCHAINS
LABELED CABLE& CORD HOLES
CANOPY w/ MOUNTED POWERSUPPLIES AND WIRES.
(FIXTURES VARY, NOT ALLARE SHOWN)
UPPER DIFFUSER
STRAIN RELIEF
LIGHT BAR
LOWER DIFFUSER
CONE POINT SET SCREW
ELEC. CORD
CABLEADJUSTERS
HOLLY HUNT LIGHTING___________________
NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS
COMPLETE.
SUSPENSION CABLES
NOTE: DO NOT OVERTIGHTEN SCREWS
CONTENTS
(1) Rectangular Canopy 108" L x 18" W
(1) Canopy Mouting Frame
(7) Light Bar, Electrical Cord and pre-installed Strain Relief with SetScrew
(7) Lower Acrylic Diffuser
(7) Upper Acrylic Diffuser
(14) Suspension Cables, Labeled and pre-marked with insertion depth
(10) Canopy Mounting Screws (#10-32)
(4) Temporary Chains w/ S-Hooks
(1) Hex Wrench
(4) Sets of Gloves to be worn during installation.
UL Approved in US and Canada
HOLLY HUNT LIGHTING___________________
NOTE: DO NOT OVERTIGHTEN SCREWS
STUDIO HEDGE CHANDELIERInstallation Instructions
INSTALLATION MUST BE PERFORMED BY A QUALIFIED ELECTRICIANPLEASE USE THE FOLLOWING DIAGRAM AND STEPS FOR INSTALLATION
NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE.
INSTRUCTIONS1. Determine fixture location, J Box should be located on the center of the Fixture.2. Screw Canopy Mounting Plate to ceiling w/ appropriate screws and/or anchors per
installation requirements. (Mounting requirements and hardware to be determinedand provided by installer)
3. Hang Temporary Chains from Canopy Mounting Plate; raise Canopy to hang fromTemporary Chains, note alignment mark on Canopy Mounting Plate and Canopy. NOTE:TEMPORARY CHAINS ARE NOT MEANT TO BE LEFT SUSPENDING THE FIXTURE FOREXTENDED PERIODS OF TIME
4. Connect 110-277 Volt power to pre-wired fixture (black and white wires). All powersupplies have been installed by manufacturer. The drivers installed in this unit havemultiple methods of dimming to accommodate your needs. The systems are capableof Triac dimming at 120 VAC or have the option for 0-10 vdc current-sinking controlfor dimming.
5. Make Electrical connections to fixture based on dimming type or controls withprovided wiring diagrams supplied with dimming or control options. (See next page fordiagrams.) This fixture can be wired to accept Triac dimming or 0-10V dimming orswitch (the 0-10V dimming signal must be supplied to the purple and gray wires asthere is no reference voltage supplied from the driver for this dimming option)). If nodimming is required cap gray and purple wires from the driver and install a non-dimming switch wired per switch instructions.
6. Slide the labeled Suspension Cables into corresponding holes through top of Canopy.7. Match the Light Bars to their corresponding labels in the Canopy and hang all Light
Bars from the Suspension Cables with Cable Adjusters to the insertion depth markedon the Cables.
8. Loosen Set Screws pre-installed in Strain Reliefs with provided Hex Wrench.9. Uncoil silver cloth covered Elec. Cord and feed through Strain Reliefs. Snug the set
screw in the Strain Relief against the Cord when the Cord is hanging straight---DONOT OVERTIGHTEN.
10. Make electrical connections with Snap Connectors at labeled positions in Canopy.Connect to Supply Power with wire nuts and Ground to Canopy.
11. Remove pre-installed 8-32 x 3/16" Cone Point Set Screws from ends of Light Barsusing provided Hex Wrench. Reaise each numbered Lower Diffuser to thecorresponding Light Bar and secure into bottom slot by re-installing Cone Point SetScrews. DO NOT OVERTIGHTEN SCREWS.
12. Install Upper Diffusers into Light Bars.13. Remove Temporary Chains and raise the Canopy to the Canopy Mounting Plate.
Secure with provided 10-32 screws (start all screws before final tightening).14. Based on site conditions, a slight leveling of Light Bars may be necessary. Pressing
the center cylinder of the Cable Adjuster will release pressure on the Cable and LightBar can be repositioned.
___________________HOLLY HUNT LIGHTINGSTUDIO H
EDGE CHANDELIERInstallation Instructions
INSTALLATION MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN PLEASE USE THE FOLLOWING DIAGRAM AND STEPS FOR INSTALLATION
NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE.
Red
Blu
e
0-10V
Power Supply
Ref. Control ModuleDimmer
Switch
Purple
Gray
White
Black
Light Bar Below Light Bar Below
Black
WhitePower Supply
Gray
Purple
Black
White
Light Bar Below Light Bar Below
Power Supply Power Supply
Power SuppliesTo More
To MorePower Supplies
Black
White
Red
Blu
e
Purple
Gray
White
Black
Gray
Purple
Wire Nut
To 120/240V J-BoxInside of Canopy
Inside of Canopy
Black
White
Inside of Canopy
Power SuppliesTo More
White
BlackPower Supply
White
BlackPower Supply
Blu
e
Red Blu
e
Red
Gra
y
Purp
lePurple
Gray
Wire Nut
Light Bar Below Light Bar Below
DimmerTriac
REFERENCE WIRING DIAGRAM FOR 0-10V DIMMING
REFERENCE WIRING DIAGRAM WITHOUT DIMMING
REFERENCE TRIAC WIRING DIAGRAM
HOLLY HUNT LIGHTING___________________HOLLY HUNT STUDIOEDGE CHANDELIERInstallation Instructions
INSTALLATION MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN PLEASE USE THE FOLLOWING DIAGRAM AND STEPS FOR INSTALLATION
NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE.
