Installation InstructionsENGLISH

Mechanical conversion Kit for active sectional triMs

5325

tahoe®

congratulations!With your purchase of this Premium entrance set, you’re among a group of discerning individuals who know the intrinsic value of selecting the finest—Baldwin. our step-by-step installation instructions will help guide you through your project quickly and easily. Before you begin your installation, read and understand the installation instructions and marking templates. if you have any questions, please do not hesitate to contact our Baldwin consumer help line at 1-800-566-1986. We’re here to help! We thank you

for your purchase and wish you the fullest enjoyment of your Baldwin product.

care and MaintenanceWarninG: Do not attempt to clean your hardware with any type of abrasive cleaners, solvents, or chemicals. these types of cleaning agents may mar the finish. a damp cloth is all that is necessary to wipe clean. note: finish number 102, oil-rubbed Bronze, can be cleaned with light machine oil and wiped with a dry cloth.

consumer help line 1-800-566-1986hours: 8 a.m. to 8 p.m. e.s.t. – Monday - friday

10 a.m. to 6 p.m. e.s. t. – saturday

if you have trouble installing your Baldwin product, feel free to call our toll-free consumer help line.

helpful tools

Putty Knife

3a remove the rosette from the adapter. Proceed to step 4.note: if your rosette is round and has a slot as illustrated, insert a flat head screwdriver into bottom slot and pry off.if your rosette is round and does not have a slot, insert a flat edge tool (examples: putty knife, pocket knife, flat head screwdriver) between the rosette and your door and pry rosette off. Be careful not to mar the door or trim.

3b Unscrew the rose retainer that secures the rosette with the rose retainer wrench provided and remove.

1 loosen the set screw using the allen wrench provided. remove the knob or lever from the spindle.

2 Unscrew the 1” round screw cover from its base.

note: if you have a tahoe design, do not remove the lower #10-32 x 23⁄4” oval head screw at this time.

4 remove the #10-32 x 11/4 screws securing the inside adapter. remove inside adapter. Discard the adapter and screws.

5 remove the spindle and spacer and discard.

Baldwin offers a vast array of exceptional solid brass products to elegantly enhance all areas of the home. each collection features a wide variety of beautiful, high-fashion finishes. from door hardware to bath accessories, Baldwin provides the discriminating decorator with numerous options to accent and complement the home’s ambience with distinction, taste, and fine detail.

remember BaldwinWith the completion of your project, remember that Baldwin quality hardware products are available for all your decorating and remodeling needs. Matching entrance sets for exterior doors, beautiful bath accessories, and a complete selection of cabinet and door-enhancing hardware are all available from your Baldwin retailer.to request a product brochure or the name of a retailer near you, call 1-800-566-1986.

Before You Begin1• follow the step-by-step sequence to ensure proper operation of your

Baldwin lockset.• We recommend spreading cardboard over the floor to prevent

scratching parts or floor.• always wear protective eyewear. note: the illustrations in these instructions depict the outside handle being installed on the right of the door. for installation of the outside handle on the left of the door, proceed as if all illustrations were reversed. Your deadbolt can remain on the door during this conversion. no deadbolt components will be replaced.

Exploded Views

(2) #10-32 x 11⁄4” Flat Head Screws

(2) #6-32 x 7⁄16” Flat Head Screws

6a supporting the handleset with one hand, unscrew and remove the lower #10-32 x 21⁄2” Pan head screw and screw cover backplate. remove the handleset.

6b supporting the handleset with one hand, unscrew and remove the lower #10-32 x 23⁄4” oval head screw and decorative screw base. remove the handleset.

7 remove the #8 x 3/4 screws securing the latch. remove latch and discard.

3 insert the new thumbpiece into the handleset.helpful hint: the new thumbpiece cannot be inserted directly into the handleset. Just reverse the steps followed to remove the old thumbpiece.

1 remove the #6-32 x 7⁄16” flat head screws that secure the thumblift cartridge to the handleset. Discard the cartridge and the screws.

2 remove the thumbpiece and discard it. helpful hint: the thumbpiece cannot be pulled directly out. instead, it must be turned from a horizontal to a vertical position and then angled to allow the lugs to fit through the slot in the handleset.

4 Position the new thumblift cartridge against the handleset, making sure the lugs on the thumbpiece seat into the pockets in the cartridge.

5 locate the new thumblift cartridge over the screw posts and secure it with the new 6-32 x 7⁄16” flat head screws provided. the post on the cartridge should be at the top, and the face of the cartridge should be flush with the surface of the handleset.caution: these screws should be “hand tightened” only — do not use a power tool!

the next steps should be performed on a padded surface such as a towel or blanket to prevent damage to your handleset’s finish.

1 Your latch is shipped with a 23⁄8” backset (most common). Adjust for a 23⁄4” backset door only. For a 23⁄4” backset, grasp body and twist faceplate 180º until it stops. Angled side of bolt should face outside.

inside

5 from inside of door, insert short end of spindle through the latch with the v groove on the long end angled down and toward hinges. Position outside handleset trim so spindle slides into square hole in thumbpiece cartridge. note: Make certain spindle is inserted through the latch to stops.

7a Position rosette onto adapter and snap into place. if your rosette has a third slot (smaller), it should face down. slide knob onto spindle and tighten set screw with allen wrench. Knob/lever is secured when set screw enters v groove in spindle. attach bottom screw cover.

5305

5315

5320

canterbury®

logan™

Madison®

Protective eyewear

Phillips screwdriver

flat head screwdriver

Pliers

required tools

inside

6 align spindle, latch, and outside handle. insert the inside adapter onto the posts of the outside handle. secure with two #10-32 x 11⁄4” flat head screws. tighten all three screws, including screw for bottom of handle.

inside

Canterbury®

Logan®

Madison®

Tahoe

Canterbury, Logan, Madison Tahoe

7b Position rosette onto inside adapter. Using rose retainer wrench, thread the rose retainer onto the threaded portion of the adapter. align rosette edge with door edge and tighten.

inside

Tahoe

inside

Canterbury, Logan, Madison

4 Measure the thickness of your door. if door is less than 13⁄4” thick, do not use the spacer provided. if your door measures 13⁄4” or more, slide the spacer onto spindle.

2 insert latch with angled side of bolt facing the doorjamb. secure with #8 x 3⁄4” combination screws from original latch so latch is flush with door. helpful hint: When installing wood screws it is recommended to put beeswax or soap on screw threads to improve installation.

3a attach handle by inserting the #10-32 x 21⁄2” pan head screw on inside of door through screw cover backplate and the lower hole. leave screw loose for adjustment. Proceed to step 4.

3b attach handle by inserting the #10-32 x 23⁄4” oval head screw on inside of door through screw base and the lower hole. leave screw loose for adjustment.

inside inside inside

V groove on bottom

toward hinges

Spindle

inside

Canterbury, Logan, Madison Tahoebottomslot

6 screw the lower post into the threaded hole at the bottom of the thumblift cartridge and tighten.

Remove Handleset from Door2 Replace the Thumblift Assembly3 Handleset Installation4

Conversion Kit Partsverify that you have all parts pictured below. if parts are missing, please call the Baldwin consumer help line at 1-800-566-1986.

inside adapter inside adapter(tahoe version only)

latch

thumbpiece

spindle spacer

thumblift cartridge Lower Post Rose Retainer Wrench(Tahoe version only)

Canterbury, Logan, Madison Tahoe

Allen Wrench

1/10

PK.1239

thumbpiece (tahoe version only)

PK.1239

8 slide knob onto spindle and tighten set screw with allen wrench. Knob/lever is secured when set screw enters v groove in spindle.

inside

Tahoe

bottomslot

outside handleset trim

latch

thumblift cartridge

#10-32 x 11⁄4” flat head screws

set screw

inside adapter

rosetteKnob/lever

screw cover

screw cover Backplate

#10-32 x 21⁄2” Pan head screw

spindle v Groove

allen Wrench

spacer#8 x 3⁄4”combination screws

thumbpiece

#6-32 7⁄16” flat head screw

lower Post

left hand lever

right hand lever

#10-32 x 11⁄4” flat head screws

set screwrose retainer

inside adapter

rosette

left hand lever

right hand lever

Knob

rose retainer Wrench

allen Wrench

latch

spindle spacer

v Groove

Decorative screw Base

#10-32 x 23⁄4” oval head screw

outside handleset trim

#8 x 3⁄4”combination screws

thumbpiecethumblift cartridge

#6-32 7⁄16” flat head screwlower Post

www.baldwinhardware.com

Browse through the Baldwin collection of beautiful locks, bath accessories and decorative hardware. compare styles and finishes. there are thousands of photos and descriptions available to help you coordinate hardware throughout your home. create your ideal “wish list” then visit your Baldwin retailer or Dealer.

©2010 Baldwin Hardware Corporation 19701 Da Vinci, Lake Forest, CA 92610

Troubleshooting Guide

spindle is installed backwards. short side of spindle must face exterior of house. long side of the spindle is installed toward inside of house. refer to handleset installation step 7. ensure that set screw on knob or lever is installed in v groove on spindle and securely tightened with allen wrench provided. refer to handleset installation step 7a or step 8 for tahoe.

inside knob or lever spins freely and does not retract latch bolt.

Knob or lever keeps coming off the spindle.

Problem Solution

Warranty InformationLimited Lifetime Mechanical Warranty – Baldwin warrants that each Baldwin product shall be free from mechanical defects at the time of delivery and for the lifetime of the product or as long as you own your home.

Limited Lifetime Finish™ Warranty – the Baldwin lifetime finish™ uses advanced finishing technology (physical vapor deposition) to create a finish highly resistant to the effects of weather and normal wear and tear. the limited lifetime finish Warranty on lifetime finish™ products covers the original purchaser for as long as you own your home.

Limited Finish Warranty – the finish on Baldwin products (excluding lifetime finish and living finish products) is protected by a durable topcoat designed to maintain the beauty and quality of the Baldwin product. the Baldwin limited finish Warranty covers the original purchaser for five years from date of purchase for interior use and one year for exterior use.

Living Finishes – Due to the nature of Baldwin living finish products, they will wear over time and may already have begun the process before reaching your home. no finish warranty is offered on living finish products, which are designed to age and improve over time. living finishes include raw brass, oil rubbed bronze, stainless steel, and other non-lacquered or non-PvD finishes.

refer to www.baldwinhardware.com for a complete warranty statement.

Installation InstructionsENGLISH

Mechanical conversion Kit for all active escUtcheon triMs

2b Unscrew the inside cylinder collar and remove it.

3 remove the rosette from the adapter. note: if your rosette is round and has a slot as illustrated, insert a flat head screwdriver into bottom slot and pry off. if your rosette is round and does not have a slot, insert a flat edge tool (examples: putty knife, pocket knife, flat head screwdriver) between the rosette and your door and pry rosette off. Be careful not to mar the door trim.

1 loosen the set screw using the allen wrench provided. remove the knob or lever from the spindle.

2a remove the #8-32 x 5⁄8” oval head screws securing the inside turnpiece and remove the assembly. Proceed to step 3.

4 remove the #10-32 x 11/4” flat head screws securing the inside adapter. Discard the adapter and screws.

5a Unscrew the #10-32 x 17/8” pan head screws. remove the outside cylinder and inside turnpiece mounting plate. Proceed to step 6.

Before You Begin1• follow the step-by-step sequence to ensure proper operation of your

Baldwin lockset.• We recommend spreading cardboard over the floor to prevent

scratching parts or floor.• always wear protective eyewear. note: the illustrations in these instructions depict the outside handle being installed on the right of the door. for installation of the outside handle on the left of the door, proceed as if all illustrations were reversed. Your deadbolt can remain on the door during this conversion.

exploded views

(2) #10-32 x 11⁄4” Flat Head Screws

(2) #6-32 x 7⁄16” Flat Head Screws

5b Unscrew the #10-32 x 2 1/4” flat head screws. remove the inside and outside cylinders. remove the cylinder base.

6 extend the deadbolt with a flat head screwdriver so the bolt head is showing.

7 remove the spindle and spacer and discard.

8 Unscrew the 1” round screw cover from its base.

3 insert the new thumbpiece into the handleset.helpful hint: to insert the new thumbpiece just reverse the steps followed to remove the old thumbpiece.

1 remove the #6-32 x 7⁄16” flat head screws that secure the thumblift cartridge to the handleset. Discard the cartridge and the screws.

2 remove the thumbpiece and discard it. helpful hint: the thumbpiece cannot be pulled directly out. instead, it must be turned from a horizontal to a vertical position and then angled to allow the lugs to fit through the slot in the handleset.

the next steps should be performed on a padded surface such as a towel or blanket to prevent damage to your handleset’s finish.

1 Your latch is shipped with a 23⁄8” backset (most common). adjust for a 23⁄4” backset door only. for a 23⁄4” backset, grasp body and twist faceplate 180º until it stops. angled side of bolt should face outside.

inside

5 from inside of door, insert short end of spindle through the latch with the v groove on the long end angled down and toward hinges. Position outside handleset trim so spindle slides into square hole in thumbpiece cartridge. note: Make certain spindle is inserted through the latch to stops.

8b Place inside turnpiece over mounting plate. insert tailpiece into inside turnpiece. attach inside turnpiece to mounting plate with two #8-32 x 5⁄8” oval head screws. Make certain turn knob rotates smoothly in both directions. tighten all screws, including screw for bottom of handle.

5370

5380

5375

nantucket®

Buckingham®

Glennon™

required tools

inside

8a Place turnpiece mounting plate on inside of door. attach to cylinder using two #10-32 x 17⁄8” pan head screws. tighten screws. important: note orientation of mounting plate.

inside

single cylinder

Double cylinder

Single Cylinder Double Cylinder

8a Keeping tailpiece vertical and curved toward right side of hole, insert inside cylinder collar base, aligning slot on top of inside cylinder with notch on inside cylinder collar base, into deadbolt. secure with two #10-32 x 21⁄4” flat head screws.

inside

7 extend deadbolt with flat head screwdriver. Keeping tailpiece vertical, insert cylinder through outside handleset and into deadbolt. hold in place. note: Do not insert key.

2 insert latch with angled side of bolt facing the doorjamb. secure with #8 x 3⁄4” combination screws from original latch so latch is flush with door. helpful hint: When installing wood screws it is recommended to put beeswax or soap on screw threads to improve installation.

3 attach handle by inserting the #10-32 x 21⁄2” pan head screw on inside of door through screw base and the lower hole. leave screw loose for adjustment.

6 align spindle, latch, and outside handleset trim. insert the inside adapter onto the posts of the outside handleset. secure with two #10-32 x 11⁄4” flat head screws. leave screws loose for adjustment.

4 Measure the thickness of your door. if door is less than 13⁄4” thick, do not use the spacer provided. if your door measures 13⁄4” or more, slide the spacer onto spindle.

inside inside inside

align tailpiece with slot so it’s vertical.

V groove on bottom

toward hinges

Spindle

insideinside

4 Position the new thumblift cartridge against the handleset, making sure the lugs on the thumbpiece seat into the pockets in the cartridge.

5 locate the new thumblift cartridge over the screw posts and secure it with the new #6-32 x 7/16” flat head screws provided. the post on the cartridge should be at the top, and the face of the cartridge should be flush with the surface of the handleset.caution: these screws should be “hand tightened” only—do not use a power tool!

6 screw the lower post into the threaded hole at the bottom of the thumblift cartridge and tighten.

10 remove the #8 x 3/4” combination screws securing the latch. remove the latch and discard.

9 supporting the handleset with one hand, unscrew the #10-32 x 21/2” pan head screws and remove that screw and screw base.remove the handleset.

Remove Handleset from Door2 Replace the Thumblift Assembly3 Handleset Installation4

conversion Kit Partsverify that you have all parts pictured below. if parts are missing, please call the Baldwin consumer help line at 1-800-566-1986.

Latch spindle spacer

Lower Post

Thumblift Cartridge Thumbpiece

Double Cylinder

Allen Wrench

1/10

PK.1239

Inside Adapter

PK.1239

8b (aerial view) align tailpiece with slot. Keep tailpiece vertical and curved toward right side of hole.note: cylinder tailpieces must overlap each other as shown.

8c align inside cylinder cap over inside cylinder. screw on inside cylinder collar. tighten all screws, including screw for bottom of handleset trim.

9 Position rosette onto adapter and snap into place. if your rosette has a third slot (smaller), it should face down. slide knob onto spindle and tighten set screw with allen wrench. Knob/lever is secured when set screw enters v groove in spindle. attach bottom screw cover.

inside inside inside

latch

#10-32 x 11⁄4” flat head screws

#8 x 3⁄4” combinationscrews

#8 x 3⁄4” combinationscrews

inside cylinder collar Base

inside cylinder assembly

#10-32 x 21⁄4” flat head screws inside cylinder cap

inside cylinder collar

set screw

inside adapter

rosette

Knob/lever

screw cover

screw cover Backplate

#10-32 x 21⁄2” Pan head screw

spindle v Groove

Deadbolt

allen Wrench

spacer

Post

lower Post

outside handleset trim

outside cylindertailpiece

latch

#10-32 x 11⁄4” flat head screws

#8 x 3⁄4” combinationscrews

#8 x 3⁄4” combinationscrews

inside turnpiece Mounting Plate

#10-32 x 17⁄8” Pan head screws

inside turnpiece

#8-32 x 5⁄8” oval head screws

set screw

inside adapter

rosette

Knob/lever

screw cover

screw cover Backplate

#10-32 x 21⁄2” Pan head screw

spindle v Groove

Deadbolt

allen Wrench

spacer

Post

lower Post

thumbpiece

Outside Handleset Trim

Outside CylinderTailpiece

Thumbpiece

bottomslot

Troubleshooting Guide

spindle is installed backwards. short side of spindle must face exterior of house. long side of the spindle is installed toward inside of house. refer to handleset installation step 5. ensure that set screw on knob or lever is installed in v groove on spindle and securely tightened with allen wrench provided. refer to handleset installation step 13.

improper alignment of cylinder and turnpiece or improper door thickness. Use a block of wood to tap cylinder collar so it will not move more than 1⁄16” in any direction. if this does not correct problem, check deadbolt hole preparation for accuracy. ensure that door is 13⁄4” thick. refer to handleset installation step 8.

inside knob or lever spins freely and does not retract latch bolt.

Knob or lever keeps coming off the spindle.

Deadbolt works easily with turn knob on inside but is difficult to turn and has grinding sound when turned with key on outside.

Problem Solution

congratulations!With your purchase of this Premium entrance set, you’re among a group of discerning individuals who know the intrinsic value of selecting the finest—Baldwin. our step-by-step installation instructions will help guide you through your project quickly and easily. Before you begin your installation, read and understand the installation instructions and marking templates. if you have any questions, please do not hesitate to contact our Baldwin consumer help line at 1-800-566-1986. We’re here to help! We thank you for your

purchase and wish you the fullest enjoyment of your Baldwin product.

care and MaintenanceWarninG: Do not attempt to clean your hardware with any type of abrasive cleaners, solvents, or chemicals. these types of cleaning agents may mar the finish. a damp cloth is all that is necessary to wipe clean. note: finish number 102, oil-rubbed Bronze, can be cleaned with light machine oil and wiped with a dry cloth.

Consumer Help Line 1-800-566-1986hours: 8 a.m. to 8 p.m. e.s.t. – Monday - friday

10 a.m. to 6 p.m. e.s. t. – saturdayif you have trouble installing your Baldwin product, feel free to call our toll-free consumer help line.

Baldwin offers a vast array of exceptional solid brass products to elegantly enhance all areas of the home. each collection features a wide variety of beautiful, high-fashion finishes. from door hardware to bath accessories, Baldwin provides the discriminating decorator with numerous options to accent and complement the home’s ambience with distinction, taste, and fine detail.

remember BaldwinWith the completion of your project, remember that Baldwin quality hardware products are available for all your decorating and remodeling needs. Matching entrance sets for exterior doors, beautiful bath accessories, and a complete selection of cabinet and door-enhancing hardware are all available from your Baldwin retailer.to request a product brochure or the name of a retailer near you, call 1-800-566-1986.

www.baldwinhardware.com

Browse through the Baldwin collection of beautiful locks, bath accessories and decorative hardware. compare styles and finishes. there are thousands of photos and descriptions available to help you coordinate hardware throughout your home. create your ideal “wish list” then visit your Baldwin retailer or Dealer.

©2010 Baldwin Hardware Corporation 19701 Da Vinci, Lake Forest, CA, 92610

helpful tools

Putty Knife

Protective eyewear

Phillips screwdriver

flat head screwdriver

Pliers

Warranty InformationLimited Lifetime Mechanical Warranty – Baldwin warrants that each Baldwin product shall be free from mechanical defects at the time of delivery and for the lifetime of the product or as long as you own your home.

Limited Lifetime Finish™ Warranty – the Baldwin lifetime finish™ uses advanced finishing technology (physical vapor deposition) to create a finish highly resistant to the effects of weather and normal wear and tear. the limited lifetime finish Warranty on lifetime finish™ products covers the original purchaser for as long as you own your home.

Limited Finish Warranty – the finish on Baldwin products (excluding lifetime finish and living finish products) is protected by a durable topcoat designed to maintain the beauty and quality of the Baldwin product. the Baldwin limited finish Warranty covers the original purchaser for five years from date of purchase for interior use and one year for exterior use.

Living Finishes – Due to the nature of Baldwin living finish products, they will wear over time and may already have begun the process before reaching your home. no finish warranty is offered on living finish products, which are designed to age and improve over time. living finishes include raw brass, oil rubbed bronze, stainless steel, and other non-lacquered or non-PvD finishes.

refer to www.baldwinhardware.com for a complete warranty statement.