V081100-A02-L 23/06/2014

INSTALLATION INSTRUCTIONS

FURNITURE

Englefield

SAPPHIRE Vanity

The classic design ofSapphire Vanities ensuresaffordable quality and timelessstyle in a range created to suitany bathroom size.

Durastone® tops and moisture resistant exteriors ensure durability, keeping your vanity looking good even in the busiest of bathrooms.

It’s the details that Englefield cares about - from pioneering the latest technology, to innovative design.

BEFORE YOU BEGIN

Please read these instructions carefully to familiarise yourself with the required tools, materials, and installation sequences. Follow the sections that pertain to your particular installation. This will help you avoid costly mistakes. In addition to proper installation, read all operating and safety instructions.

All information is based on the latest product information available at the time of publication. Englefield reserves the right to make changes in product characteristics, packaging, or availability at any time without notice.

Please leave these instructions for the consumer.They contain important information.

Floor Standing Models

Double Bowl Model

16949A-0

16946A-0 37429A-0 37427A-0 37425A-0

16986A-0 16948A-0 16947A-0

Wall Hanging Models

ROUGH-IN

STEP 1

STEP 2

STEP 3

INSTALLATION

Page 2 ENGLEFIELD

INSTALLATION INSTRUCTIONSSAPPHIRE Vanity

Prior to installation, inspect cabinet to ensure that no damagehas occurred in transit.

If damage has occurred, or a visible defect exists, do not pro-ceed with installation, and advise your supplier immediately.

On timber walls, ensure that there is frame work behind thecabinet’s back rail or wall, to screw into when fixing the cabinetto the wall.

To make installation easier, remove the door(s) and drawer(s).Be sure to store them in a place where they won’t get damaged!

Measure and mark the hole centres for pipes (water supply and waste) on the base and back panel as required.

For wall hung vanities, determine the desired height for the vanitytop at this point. Between 800 and 850mm from floor to vanity top is recommended.

Ensure that there are 2 appropriate horizontal nogs in the wall to allow the vanity cabinet to be adequately fastened to the wall.

With a suitable sized hole saw, drill the holes for water supply and waste

Having drilled the required holes, �t the cabinet into positionover the pipework.

Before proceeding to �x the cabinet into position make surethat the cabinet is sitting level and square and the �oor at the selected location is �at and free of bumps and protrusions.

STEP 6

INSTALLATION

Page 3 ENGLEFIELD

INSTALLATION INSTRUCTIONSSAPPHIRE Vanity

Drill holes through the back rail or wall to align with nogsthe wall behind, and then fix the cabinet to the wall.Note: Wall fixings are not supplied.

Wall hung vanities must be fastened to a 75x50 nog or stud in the wall using a minimum of 10g 75mm hex head wood screws with a20mm washer to ensure the load is spread evenly.

A guide to the number of fasteners to use is given below.600 wide = 5 screws, 900 wide = 7 screws, 1200 wide = 9 screws .

Screws should be positioned in a general pattern as indicated by the “+” marks in the diagram for a 600 wide vanity.

When fixing to masonary walls use appropriate masonary fastenersas a substitute for the screws.

Check vanity tops stability on the cabinet.If the top is rocking slightly use wedges supplied.Apply a continuous bead of silicone on the top edge of the cabinet.

This will ensure that the vanity top stays securely fitted to the cabinet and no water spillage will find it’s way into the cabinet through the joint.

Important: Ensure no gaps are left in the sealant bead.Note: Sealant not supplied. (Recommended sealant is Sika Silaflex NG white).

Unpack top and check for any damage that might have occurred in transit.

Check and confirm the fit of your selected tapware.Place vanity top onto the cabinet ansuring that the back is flush against the wall and there is an even overhang each side of the cabinet.

Wipe off any excess sealant.

= =

50mm50mm horizontal nogs

75x50mm

STEP 8

INSTALLATION

Page 4 ENGLEFIELD

INSTALLATION INSTRUCTIONSSAPPHIRE Vanity

Fit the waste and the tapware.

Connect the water supply to the taps and waste pipe to the waste outlet.

Run hot and cold water and check for leaks.

When satisfied with the results move to step 8.

Refit the doors and adjust the door hinges to ensure an evenclearance. Check the number printed underneath each drawer and refit them in the right order.

Drawer 1 is the top drawer, followed with 2 and 3 below.

Adjustment of the doors can be achieved as follows:

All edges MUST be sealed with an approved Silicone Sealant.

9a. To adjust IN or OUT 9b. To adjust UP or DOWN 9c. To adjust LEFT or RIGHT

10a. Between cabinet and floor. 10b. Between cabinet and wall. 10c. Between upstand and wall.

CLEANING AND MAINTENANCE INSTRUCTIONS

All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc. which could adversely affect the finish and are not recommended for cleaning.

Do not use abrasive cleaners or solvents on Englefield vanities.

In the event of light scratches in the surface of the top, a mild abrasive such as “Meguiars Mirror Glaze 28 All Metal Polish” or “3M Marine One Step Painted Aluminium Cleaner and Wax” can be used to polish them out.

CONTACT AND WARRANTY INFORMATION

NEW ZEALAND KOHLER NZ LTDFree Ph: 0800 100 382Free Fax: 0800 664 488www.englefield.co.nz

AUSTRALIA KOHLER CO.

Free Ph: 1 800 228 476

www.englefield.com

For warranty information, please visit our website

SPARE PARTS

Page 5 ENGLEFIELD

INSTALLATION INSTRUCTIONSSAPPHIRE Vanity

CAUTIONMaterial used in cabinet is water resistant only, not waterproof.

Care must be taken to clean up all water spillage.

WARNINGFOR YOUR PERSONAL SAFETY AND PRODUCT DURABILITY,

ENSURE THAT HOT WATER SUPPLY IS REGULATED TO 55 C MAXIMUM

Drawer runner kit 1096827

Handle kit 1096826-CP

Bumper dome S000310

Shelf pin 86931

Outer side of hinge 1100323

Door side of hinge 1100324

Toe kick rails

Acrylic aprons

1117212-0

1096830-0

1117213-0

1096831-0

1117234-0

1096832-0

1117215-0

1096833-0

1117215-0

1096834-0

600 wide 750 wide 900 wide 1200 Single bowl 1200 Double bowl