Installation Instructions Citroen C5 / Peugeot 407автоотопитель.рф/manual/Citroen/C5/1314450A_EN... · Citroen C5 / Peugeot 407 1314450A_EN 2 Table of Contents Validity

WARNING!

Hazard warning:

Incorrect installation or repair of Webasto heating systems may cause a fire or result in the emission of carbon monoxide, which can be fatal. Serious or fatal injuries can be caused as a result.

Specialist company training, technical documentation, specialized tools and equipment are required to install and repair Webasto heating and cooling systems.

NEVER attempt to install or repair Webasto heating or cooling systems if you have not suc-cessfully completed the company training and thereby acquired the required technical skills, or if you do not have access to the required technical documentation, tools and equipment needed to carry out correct installation and repairs.

ALWAYS follow all Webasto installation and repair instructions and observe all warnings.

Webasto does not accept any liability for defects and damage that are attributable to installa-tion by untrained staff.

Water Heater Unit

Installation Instructions

Ident. No.:1314450A_EN Fee Euro 10.00 © Webasto AG

Citroen C5 / Peugeot 4072.7 HDIfrom Model Year 2008Left-hand drive vehicleAutomatic air-conditioningAutomatic transmission

Feel the drive

Thermo Top V Additional Heatere1

00 0018

Citroen C5 / Peugeot 407

Table of Contents

Validity

Vehicle and engine types, equipment variants and national specifications not listed in these installation instructions have not been tested. However, installation according to these installation instructions may be possible.

The installation location of the digital timer should be confirmed with the end customer before installa-tion.

Manufacturer Model Type EG-BE No./ABECitroen C5 R.... e2 * 2001/116 * 0360 *...

Manufacturer Model Type EG-BE No./ABEPeugeot 407 6 e2 * 2001/116 * 0328 * ...

Engine type Engine model Output in kW Displacement in cm³UHZ Diesel 150 2720

Validity 2Heater Unit/Installation Kit 3Foreword 3General Instructions 3Special Tools 3Explanatory Notes on Document 4Preliminary Work 5Heater unit installation location 5Preparing electrical system 6Electrical system 7

Fan controller 8Heater controls 10Digital timer option 11Remote option (Telestart) 11Preparing installation location 13Installing heater unit 13Coolant 14Fuel 16Final Work 19Template for Fuel Standpipe 20

1314450A_EN 2


Heater Unit/Installation Kit

Optional heater control either:

ForewordThese installation instructions apply to Citroen C5 / Peugeot 407 2.7 HDI vehicles - for validity, see page 2 - from model year 2008 and later, assuming technical modifications to the vehicle do not affect installation, any liability claims excluded. Depending on the vehicle version and equipment, modifica-tions may be necessary during installation with respect to these installation instructions.

However, where this is the case the stipulations in the "installation instructions" and "operating and maintenance instructions" for the Thermo Top V should be observed.The corresponding rules of technology and any information from the vehicle manufacturer should be observed during the installation work.

General InstructionsInstallation should be carried out according to the general, standard rules of technology. Unless spec-ified otherwise, fasten hoses, lines and wiring harnesses to original vehicle lines and wiring harnesses using cable ties.Sharp edges should be fitted with edge protectors (split-open plastic hose).Spray unfinished body areas, e.g. drilled holes, with anti-corrosion wax (Tectyl 100K, Order No. 111329).

Special Tools- Torque wrench for 2.0 - 10 Nm- Hose clamping pliers

Quantity Description Order No.:1 Delivery Scope of Citroen C5 / Peugeot 407 Diesel

Automatic Transmission1313878B

Quantity Description Order No.:1 Digital timer See price list1 Telestart T91 See price list1 Telestart T100 HTM See price list1 Y-adapter (with combination of digital timer and Telestart) 9001505A

1314450A_EN 3


Explanatory Notes on Document

To provide you with a quick overview of the individual working steps, you will find an identification mark on the outside top right corner of the page in question.

1314450A_EN 4

Special features are highlighted using the following symbols:

The arrow in the vehicle icon indicates the position on the vehicle and the viewing angle.

Specific risk of injury or fatal accidents.

Specific risk of damage to components.

Specific risk of fire or explosion.

Reference to general installation instructions of Webas-to components or to the manufacturer's vehicle-specific documents.

Reference to a special technical feature.

All dimensions are in mm!Tightening torque of hose clamps = 2.0 + 0.5 Nm!Tightening torque of Ejot screws, Ejot studs = 10 Nm!

Mechanical system

Electrical system

Water

Fuel

Exhaust gas

Combustion air


Preliminary Work

WARNING!

- Open fuel tank cap, ventilate tank.- Close the tank cap again.- Disconnect the battery "earth" or "ground" connection.- Depressurize the cooling system.- Copy the factory number from the original type label to the duplicate type label.- Remove years that do not apply from the duplicate label.- Attach the duplicate label (type label) in the appropriate place.- Remove the left-hand wheel well trim.- Remove the left front wheel.- Remove the front underride protection.- Remove the right rear underride protection.- Fold over the right-hand rear seat- Open the right-hand fuel sender service lid.- Remove the instrument panel trim on the driver's side (only with Telestart).- Remove the footwell trim on the driver's side.- Remove the driver's side storage compartment.

Installa-tion loca-tion

Heater unit installation location

1 Heater unit

1

1

1314450A_EN 5


Preparing fuse F3 and K3 re-lay

Preparing K3 relay

Preparing wiring har-ness of digital tim-er

Positive and ground connection

Preparing electrical system

Cut off black (sw) wire 5 (0.75 mm²) from wir-ing harness of heater unit. Cut off red/white (rt/ws) wire 6 (4 mm²) of fuse F3. Remove in-sulation from ground wires to node point and cut off brown (br) wire 4 (0.75 mm²) from wir-ing harness of digital timer.Remove red/white (rt/ws) wire 1 (4 mm²) from K3/87, red (rt) wire 3 (4 mm²) from K3/87a and black (sw) wire 2 (4 mm²) from K3/30.

Insulate and tie back ends of red/white (rt/ws) wire 3 and black (sw) wire 2. Insulate ground wires 1.

Insert brown (br) wire 2 (0.75 mm²) from wir-ing harness of heater controls in K3/30.Also connect black (sw) wire 1 to K3/85 and to K3/87.

Strip insulation from approx. 50 mm of wiring harness of digital timer 3. Crimp microtimer 1 onto brown (br) wire (0.75 mm²). Insert yellow (ge) wire 2 in free socket of digital timer con-nector.

Illustration shows Citroen C5!Connect positive wire 1 to positive terminal and ground wire 2 to original vehicle ground support point.

3

6

1

25

2

4

1

2 3

13

2

4

1

23

5

1 1

1314450A_EN 6


Wiring har-ness in-stallation diagram

Electrical systemFuse holder, K3 relay on Citroen C5

1 Original vehicle bolt2 Angle bracket3 M5x16 bolt, retaining plate for fuse holder,

large diameter washer, flanged nut4 K3 relay

Fuse holder, K3 relay on Peugeot 407

1 K3 relay2 Angle bracket3 Original vehicle bolt4 M5x16 bolt, retaining plate for fuse holder,

large diameter washer, flanged nut

Wiring harness routing

Fasten wiring harness of digital timer 2 in wheel well with adhesive base 3 and cable tie [total of 4x each].

Wiring harness pass through of passenger compartment

1 Drill out existing protective rubber plug2 Wiring harness of digital timer 3 Adhesive base, cable tie

6

4

1 2

3 74

3

21

Do not install the metering pump cable harness until later together with fuel pipe in the corrugated tube along the original vehicle line on the underbody

8

11

2 93 2

1

1314450A_EN 7


Wiring dia-gram

Legend

Fan controller

Webasto components Vehicle compo-nents

Colors and symbols

HG Heater unit TT-C/E BSI Central electri-cal box for pas-senger compartment

gn greenVWU Digital timer ws white

Tele Telestart St A 20-pin connec-tor BSI

rt redF3 Fuse removed br brown1 Wiring harness of heater unit sw black2 Wiring harness of digital timer

Mount yellow (ge) wire in free socket of 4-pin connector of heater-unit wiring harness.Insulate wire ends and tie back

Cable and connectorcolors may vary!

Webasto

31

3015

Citroen / Peugeot

HG

0,5²

br0,75²

br

0,75²

!

gn/ws

br

rt/ws

sw

BSI

6 St A

86

85 30

87a87

K3

1

2

F3

1314450A_EN 8


Detaching BSI and routing downward

Pulling connector off BSI and removing

Connec-tion of BSI

View of BSI.

1 Socket for 2-piece connector. 40-pin

Press in locking lug 1 and fold down bar 2.

3 2-piece connector

Connection on 20-pin connector 1 from BSI (connector color may vary)!Insert microtimer from brown (br) wire 3 in PIN 6. Route wiring harness of digital timer 2 upward to installation location of digital timer.Produce connections as shown in wiring dia-gram.

10

1

1

11

1

3

2

12

1

2

3

1314450A_EN 9


Diagram for digital timer

Preparing connector of Tele-start re-ceiver for T91

Preparing connector of Tele-start re-ceiver for T100 HTM

Diagram for digital timer with Telestart

Heater controls

Digital timer only

Telestart T91

Modify wiring harness from remote control set T91 as follows:

Remove violet (vi) wire 2 from socket 5 and insert in socket 2.

1 6-pin connector

Telestart T100 HTM

Modify wiring harness from remote control set T100 as follows:

Disconnect yellow (ge) wire 2 from socket 2. Remove violet (vi) wire 3 from socket 5 and connect to yellow (ge) wire 2. Discard micro-timer of violet (vi) wire 3.

1 6-pin connector

Switch-on display for Telestart in digital timer:"Tele On"!Y-adapter with T91 = 67089AY-adapter with HTM 100 = 9010951A

9001810F

Heater unit

digital timer

13

2

5

1

2

1423

52

1

9001505A

6708

9A *

9010

951A

**

Telestart

digital timer

9001810FHeater unit

Temperature sensor only with HTM 100

1314450A_EN 10


Installing digital tim-er

Installing digital tim-er

Installing receiver

Installing receiver

Digital timer option

Citroen C5

1 Digital timer

Peugeot 407

1 Digital timer

Remote option (Telestart)

Citroen C5

Mount connector (6-pin) from adapter wiring harness on receiver 2.

1 Double-sided adhesive tape

Peugeot 407

Mount connector (6-pin) from adapter wiring harness on receiver 2.

1 Double-sided adhesive tape

1 15

1 16

1

2 17

1

2

18

1314450A_EN 11


Installing antenna

All vehicles

1 Antenna

1 19

1314450A_EN 12


Reposi-tioning connector

Installing edge pro-tection

Installing heater unit

Installing bracket

Preparing installation location

Move connector from position 2 (if present) to position 3.

1 Fastening point for heater unit (existing hole)

2 Fastening point for heater unit (existing hole)

Loosen bolt at position 2 (fastening point for heater unit).

1 100 mm edge protection

Installing heater unit

Mount stud bolts from bracket in existing holes.

1 Large diameter washer, flanged nut [2x each], stud bolt

1 Mount wiring harness of heater unit2 Bracket of heater unit3 Original vehicle bolt

20

1 2

3

21

1 2

4

5

22

1 1

23

2 31

1314450A_EN 13


Coolant routing di-agram

Coolant

WARNING!Any coolant running off should be collected using an appropriate container. Install coolant hoses kink-free. Unless specified otherwise, always fasten using cable ties. Position clamps so that no other hose can be damaged! When installing the coolant hose, the heater unit must be filled with coolant.The connection should be "inline" based on the following diagram:

All spring clips without a specific designation = 27 mm dia.All connecting pipes = 18x20 mm dia.

B

A

Ø 25

Ø 25

1314450A_EN 14


Cutting coolant hoses to length

Cutting point

Connect-ing heat exchanger inlet

Connect-ing engine outlet

Shorten hose A = straight endShorten hose B =180° elbowDiscard section X

1 Hose section of heat exchanger inlet2 Engine outlet hose section

Connect hose B with long leg to heater unit outlet.

1 Hose on heat exchanger inlet

Connect hose A on circulating pump inlet.

1 Hose of engine outlet

45

X

B

A X

135

24

1

2

25

b

1

26

1

a 1

1314450A_EN 15


Preparing corrugat-ed tube

Connect-ing heater unit

Routing line

Fuel

CAUTION!Open the vehicle's fuel tank cap, ventilate the tank and then re-close the tank lock.

Catch any fuel running off with an appropriate container.

Install fuel line and metering-pump wiring harness so that they are protected against stone impact. Un-less specified otherwise, always fasten using cable ties.Mount the fuel line and wiring harness with rub protection on sharp edges.

WARNING!The fuel line and wiring harness are routed to the metering pump in as shown in the wiring harness routing diagram.

Cut approx. 400 mm off first corrugated tube.

1 Fuel line in corrugated tube 12 10 mm dia. Caillau clamp, 90° molded

hose

1 Metering pump wiring harness2 Fuel line in corrugated tube 13 Fuel line, wiring harness of metering pump

in corrugated tube 2

27

400

21

3

4

28

1

2

29

1

3

2

1314450A_EN 16


Installing lines

Installing metering pump

Installing metering pump

Connect-ing meter-ing pump

1 Fuel line, wiring harness of metering pump in corrugated tube 3

Remove original vehicle nut at position 1 and discard.

2 Large diameter washer, 30 mm spacer nut

1 Metering pump2 Bracket of metering pump3 M6x20 bolt, spring lockwasher, large diam-

eter washer

1 Fuel line in corrugated tube 42 Hose section [2x], 10 mm dia. Caillau

clamp [4x]3 Fuel line, wiring harness of metering pump

in corrugated tube 34 Wiring harness of metering pump, connec-

tor mounted

30

1

31

1

2

32

1 2

3

33

21

4

2 3

1314450A_EN 17


Removing fuel

Installing fuel stand-pipe

Connect-ing fuel line

Remove fuel-tank sending unit 1 in accor-dance with manufacturer's specifications.

2 Copy hole pattern, 6 mm dia. hole3 5 mm dia. large diameter washer

Shape fuel standpipe 1 according to tem-plate, cut to length and install.

Check the position of the components; adjust if necessary. Check that they have free clear-ance.Install fuel-tank sending unit according to manufacturer's specifications.

1 Hose section, 10 mm dia. Caillau clamp [2x]

2 Fuel line

34

1

2

3

35

1

36

21

1314450A_EN 18


Cutting out underride protection

Mounting underride protection

Final Work

WARNING!Reassemble the disassembled components in reverse order.Check all hoses, clamps and all electrical connections for firm seating.Secure all loose cables using cable ties.Only use manufacturer-approved coolant.Spray heater unit components with anti-corrosion wax (Tectyl 100K, Order No. 111329).

- Connect the battery.- Fill and bleed the coolant circuit according to the vehicle manufacturer’s specifications.- Set the digital timer.- Code the BSI for the additional heater in accordance with the manufacturer's instructions.- Check the proper operation of the additional heater, see the operating instructions/installation in-

structions.- Attach the "Switch off additional heater before refueling" sticker to the left-hand B-pillar.

1 Underride protection2 Cut out exhaust outlet along perforation

Align underride protection 1 (exhaust end section centered in cut-out).

2 Exhaust end section

372

1

382

1

Feel the driveWebasto AGPostfach 80 - 82132 StockdorfHotline 01805 / 932278 - Hotfax 0395 / 5592-353http://www.webasto.de

Printed in Germany 02/2009 Printing: Stef-fen

1314450A_EN


Template for Fuel Standpipe

1314450A_EN 200

100 mm

100 mm

Scale 1:1

Compare the size of the printed version with dimension lines.Permitted tolerance a maximum of 2%.

Set the printer settings to “no margin” or “minimize mar-gins” and 100% of the normal size.

Documents

Installation Instructions Citroen C5 / Peugeot 407автоотопитель.рф/manual/Citroen/C5/1314450A_EN... · Citroen C5 / Peugeot 407 1314450A_EN 2 Table of Contents Validity