Manufacturer reserves the right to discontinue, or change at any
time, specifications or designs without notice and without
incurring obligations.Catalog No. 04-53090021-01 Printed in U.S.A.
Form 09/30/38-14SI Pg 1 10-13 Replaces: 09/30/38-11SI
Installation InstructionsPart No: 30RA-900---064,
30RA-900---065, 30RA-900---066, and 38AP-900---005
PACKAGE USAGE
PACKAGE CONTENTS
GENERALThis book contains instructions for the installation of
the
wind baffles used on 09DPS018-030, 09DPM035-130,30RAP010-150,
38APD025-130, and 38APS025-065 unitswith Motormaster® V controls.
The Motormaster V controlmust be purchased separately and is not
provided with this kit.Wind baffles must be field installed for all
units to ensure prop-er operation at low-ambient temperatures with
Motormaster Velectronic controller. If the unit is equipped with
hail guards,they must be removed before installing the wind
baffles.
This kit provides factory designed wind baffles for field
in-stallation when running the unit at low ambient air
tempera-tures.
The standard outdoor-air temperature limitation of
the30RAP010-015 chillers is –20 F (–28.0 C). The
standardoutdoor-air temperature limitation of the 30RAP018-030
chill-ers is 45 F (7.2 C). The standard outdoor-air temperature
limita-tion of the 30RAP035-150 chillers is 32 F (0.0° C).
The standard outdoor-air temperature limitation of
the38APS025-065 condensing units is 45 F (7.2 C). The standard
outdoor-air temperature limitation of the 38APD025-040
and070-130 condensing units is 32 F (0.0° C). The standard
out-door-air temperature limitation of the 38APD050-060 condens-ing
units is 25 F (–3.9 C).
The standard outdoor-air temperature limitation of the09DPS and
09DPM units is based on different system factors in-cluding the
unit it is paired with, condensing temperature, tem-perature
difference, and compressor capacity.
The Motormaster V electronic control low ambient opera-tion kit
can be used to extend the system operation down to–20 F (–28
C).
SAFETY CONSIDERATIONS
Installation of this accessory can be hazardous due to sys-tem
pressures, electrical components and equipment location.
Only trained, qualified installers and service techniciansshould
install, start up, and service this equipment.
When installing this accessory, observe precautions in
theliterature and on tags, stickers, and labels attached to the
equip-ment.• Follow all safety codes.• Wear safety glasses and work
gloves.• Use care in handling equipment.
PREINSTALLATIONInspect the contents of the accessory package
before install-
ing. File a claim with the shipper if shipping damage is foundor
contact your Carrier representative if any parts are missing.See
Package Contents table for kit package contents.
INSTALLATION
NOTE: Pre-drilled holes may not be provided. Drill pilot holesas
necessary using the bracket as a template.
All Units Sizes 010 to 060 — To install the accessorywind
baffles, perform the following procedure:
1. Install the 3 brackets to the side of the unit using
screwsprovided. See Fig. 1-3 for location.
ACCESSORYPART NUMBER QUANTITY UNITS
30RA-900---064 1 30RAP010,015
30RA-900---0651
09DPS018,02030RAP018,020
38APD02538APS025
2 09DPM035-05030RAP035,040
30RA-900---066
1
09DPS03030RAP025,03038APD027-03038APS027-030
2
09DPM06030RAP045-06038APD040-06038APS040,050
38AP-900---005 1
09DPM065-13030RAP070-150
38APS06538APD070-130
ACCESSORYPART NUMBER
CONTENTSDESCRIPTION QUANTITY
30RA-900---064,30RA-900---065,30RA-900---066
Baffle Plate 1Baffle Plate 1Bracket 3Support Bracket 2Screws 36
or 40
38AP-900---005Baffle Plate 1Screw 12
WARNING
Disconnect all power to the unit before performing mainte-nance
or service. Electrical shock and personal injury couldresult.
CAUTION
To avoid damage to refrigerant coils and electronic compo-nents,
use extreme care when drilling screw holes andattaching
fasteners.
09DPS018-030, 09DPM035-13030RAP010-150
38APD025-130, 38APS025-065Wind Baffle Accessory
Manufacturer reserves the right to discontinue, or change at any
time, specifications or designs without notice and without
incurring obligations.Catalog No. 04-53090021-01 Printed in U.S.A.
Form 09/30/38-14SI Pg 4 10-13 Replaces: 09/30/38-11SI
© Carrier Corporation 2013
74.00
27.50
TYP0.50
TYP1.07
2 SPA @ 12.13 = TYP
24.26
TYP0.62
2.05
TYP0.62
TYP0.62
1.00 TYP0.45
14.13
29.69
44.33
59.89
2X R0.156
REF1.07
71.95
TYP1.28
REF0.25
TYP3.00TYP
68.00
9.00
18.00
10X 0.312
8X 45 X CHAMFEROR 0.25 RTO SIUT TOOLING
0.13
SEE DETAIL A
B
B
B
B
DETAIL A
STIFFENING RIBTO SUIT TOOLING
SECTION B-B
NOTE: Dimensions are in inches.
Fig. 4 — Baffle Dimensions — 09DPM065-130 Units, 38APD070-130
Units, 38APS065 Units, and 30RAP070-150 (Part No.
38AP-900---005)
BAFFLEINSTALLATIONLOCATION
Fig. 5 — Baffle Installation Location — 09DPM065-130 Units,
38APD070-130 Units,38APS065 Units, and 30RAP070-150 (Part No.
38AP-900---005)
