Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
1WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
waclighting.comPhone (800) 526.2588Fax (800) 526.2585
Headquarters/Eastern Distribution Center44 Harbor Park Drive Port Washington, NY 11050
Central Distribution Center1600 Distribution CtLithia Springs, GA 30122
Western Distribution Center 1750 Archibald Avenue Ontario, CA 91760
HARDWARE
WARNINGIMPORTANT: NEVER attempt any work without shutting off the electricity.- Read all instructions before installing.- System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations.- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF” the circuit breaker switch(es) that control the power to the fixture or room that you are working on.- Place the wall switch in the “OFF” position.
CAUTION- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this fixture. CAUTION When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
AVERTISSEMENTIMPORTANT : Coupez l’électricité avant TOUTE manipulation.- Lisez toutes les instructions avant d’installer.- Système est destiné à être installé par un électricien qualifié en conformité avec le code national de l’électricité et les règlements locaux. - Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt (« OFF »). - Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIAIMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico. - Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta lámpara.- Sistema está disenado para ser instalado por un electricista calificado, de acuerdo con el código eléctrico nacional y las normas locales. - Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación principal en la posición “OFF” (APAGADO). - Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calificación ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
INSTALLATION INSTRUCTION131 - LED Flush MountFM-13114
Wire ConnectorQty: 3 pcs + 1 Extra
Junction Box ScrewQty: 2 pcs + 1 Extra
#8-32x1Zinc Plating
Mounting ScrewQty: 1 Extra5/32-32x1/2
BN
Plastic AnchorQty: 3 pcs + 1 Extra
Wood ScrewQty: 3 pcs + 1 Extra
Ø4x35
A1 B1 C1 D1 E1
PD-16818,PD-16824,PD-16830168-LED Flush Mount
1Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JANUARY, 2017
modernforms.comPhone (800) 526.2588Fax (800) 526.2585
Headquarters/Eastern Distribution Center44 Harbor Park Drive Port Washington, NY 11050
Central Distribution Center1600 Distribution CtLithia Springs, GA 30122
Western Distribution Center 1750 Archibald Avenue Ontario, CA 91760
Wire Connector Qty: 3 pcs+1 Extra
G0 Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
WS-W81612816-Vanities & Wall Sconce
A B C D E F G H I
2WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
waclighting.comPhone (800) 526.2588Fax (800) 526.2585
Headquarters/Eastern Distribution Center44 Harbor Park Drive Port Washington, NY 11050
Central Distribution Center1600 Distribution CtLithia Springs, GA 30122
Western Distribution Center 1750 Archibald Avenue Ontario, CA 91760
INSTALLATION INSTRUCTION131 - LED Flush MountFM-13114
PREPARATION 1. Shut off the power at the circuit breaker and remove existing fixture, including the crossbar.2. Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
CONNECTING THE WIRES (Fig. 2)3. Remove the mounting screws (C1) from fixture. 4. Drill holes in the ceiling aligned with the key holes located in the mounting plate, insert the plastic anchors (D1).5. Connect the fixture’s input wires to junction box wires as shown in Fig. 2, making sure that all wire connectors (A1) are secured.
If your outlet box has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
MOUNTING THE FIXTURE (Fig. 1)6. Secure the mounting plate to the junction box using junction box screws (B1),
fasten it to the wall using wood screw (E1). The side of the mounting back plate marked “GND” must face out.
7. Insert the PC diffuser into the fixture shade.8. Secure the fixture onto mounting plate with mounting screws (C1).
Fixture WiresBlack or Smooth
Fixture WiresWhite or Ribbed
Fixture WiresBare wire(Ground)
House WiresBlack(Hot)
House WiresWhite (Neutral)
House WiresGreen or Bare Copper(Ground)
Fig. 2 Wiring
Plastic Anchor
Wire Connector
Wood Screw
Junction Box Screw
Mounting Screw
Fixture Shade
PC Diffuser
Mounting Plate
Junction Box
Glass(RPL-GLA-13114)
Shade(RPL-SHA-13114)
D1
A1
E1
B1
C1
FIG. 1
Ø7"
Back Plate Dimensions
Ø8 3/4"
Ø2 3/4"
Ø3 1/2"
PD-16818,PD-16824,PD-16830168-LED Flush Mount
1Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JANUARY, 2017
modernforms.comPhone (800) 526.2588Fax (800) 526.2585
Headquarters/Eastern Distribution Center44 Harbor Park Drive Port Washington, NY 11050
Central Distribution Center1600 Distribution CtLithia Springs, GA 30122
Western Distribution Center 1750 Archibald Avenue Ontario, CA 91760
Junction Box
Mounting Plate
Canopy
Stem
FixtureShade
PC Diffuser
Glass(RPL-GLA-13114)(RPL-GLA-13120)(RPL-GLA-13126)
Shade(RPL-SHA-16818)(RPL-SHA-16824)(RPL-SHA-16830)
Diffuser(RPL-DIF-13114)(RPL-DIF-13120)(RPL-DIF-13126)
PD-16818 4 3/4"
PD-16824 4 3/4"
PD-16830 4 3/4"
PD
-168
18 4
3/4
"
PD
-168
24 4
3/4
"
PD
-168
30 4
3/4
"
PD
-168
18
2 -1
/2"
PD
-168
24
2 -1
/2"
PD
-168
30
2 -1
/2"
G0 Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
Junction Box
Mounting Plate
Canopy
Stem
FixtureShade
PC Diffuser
Glass(RPL-GLA-13114)(RPL-GLA-13120)(RPL-GLA-13126)
Shade(RPL-SHA-16818)(RPL-SHA-16824)(RPL-SHA-16830)
Diffuser(RPL-DIF-13114)(RPL-DIF-13120)(RPL-DIF-13126)
PD-16818 2-1/2"
PD-16824 2-1/2"
PD-16830 2-1/2"
PD-16818 4 3/4"PD-16824 4 3/4"PD-16830 4 3/4"
3. Remove the mounting screw (C) from the fixture.
5. Choose number of rods suitable for your application.6. Thread the fixture wire through the rods and canopy.7. Connect the canopy, rods and lamp body. Make sure all are tightened.
8. Cut the extra wire. Connect the fixture’s input wires to junction box wires as shown in Fig.2, making sure that all wire connectors (A) are secured. If your outlet box has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
9. Insert the PC diffuser into the fixture shade.
4. Secure the mounting plate to the junction box using junction Box screws(B).The side of the mounting back plate marked “GND” must face out.
MOUNTING THE FIXTURE (Fig. 1)
1. Shut off the power at the circuit breaker and remove existing fixture, including the crossbar.2. Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not lose any small parts necessary for installation.
PREPARATION
CONNECTING THE WIRES (Fig. 2)
COMPLETING THE INSTALLATION (Fig. 1, 2)
10. Secure the fixture onto mounting plate with mounting Screws(C).11. For slope ceiling application, rotate wire at the top of the stem to ensure luminaries is aiming down.
Fixture WiresBlack or Smooth
Fixture WiresWhite or Ribbed
Fixture WiresBare wire(Ground)
House WiresBlack(Hot)
House WiresWhite (Neutral)
House WiresGreen or Bare Copper(Ground)
Fig. 2 Wiring
WS-W81612816-Vanities & Wall Sconce
B
H
Adjustable Nut
C
Switch Box
Driver 2 7/8"L x1 3/8"W x1 1/8"H
Fixture
G
AMounting Plate
I
"x " "
Mounting Plate
FE
C
D
G
Adjustable Nut
FixtureBackplate
I
FIG.1 MOUNT ON SWITCH BOX FIG.3
FIG.2 MOUNT ON JUNCTION BOX FIG.5
Caulking
Junction Box
te, insert the plastic anchors (D1).ng sure that all wire connectors (A1) are secured.
Fixture WiresBlack or Smooth
Fixture WiresWhite or Ribbed
House WiresBlack(Hot)
House WiresWhite (Neutral)
Fig. 2 Wiring
Fixture WiresBlack or Smooth
Fixture WiresWhite or Ribbed
Fixture WiresBare wire(Ground)
House WiresBlack(Hot)
House WiresWhite (Neutral)
House WiresGreen or Bare Copper(Ground)
Fig. 2 WiringFig.4 Wiring
2WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
waclighting.comPhone (800) 526.2588Fax (800) 526.2585
Headquarters/Eastern Distribution Center44 Harbor Park Drive Port Washington, NY 11050
Central Distribution Center1600 Distribution CtLithia Springs, GA 30122
Western Distribution Center 1750 Archibald Avenue Ontario, CA 91760
INSTALLATION INSTRUCTION131 - LED Flush MountFM-13114
PREPARATION 1. Shut off the power at the circuit breaker and remove existing fixture, including the crossbar.2. Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
CONNECTING THE WIRES (Fig. 2)3. Remove the mounting screws (C1) from fixture. 4. Drill holes in the ceiling aligned with the key holes located in the mounting plate, insert the plastic anchors (D1).5. Connect the fixture’s input wires to junction box wires as shown in Fig. 2, making sure that all wire connectors (A1) are secured.
If your outlet box has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
MOUNTING THE FIXTURE (Fig. 1)6. Secure the mounting plate to the junction box using junction box screws (B1),
fasten it to the wall using wood screw (E1). The side of the mounting back plate marked “GND” must face out.
7. Insert the PC diffuser into the fixture shade.8. Secure the fixture onto mounting plate with mounting screws (C1).
Fixture WiresBlack or Smooth
Fixture WiresWhite or Ribbed
Fixture WiresBare wire(Ground)
House WiresBlack(Hot)
House WiresWhite (Neutral)
House WiresGreen or Bare Copper(Ground)
Fig. 2 Wiring
Plastic Anchor
Wire Connector
Wood Screw
Junction Box Screw
Mounting Screw
Fixture Shade
PC Diffuser
Mounting Plate
Junction Box
Glass(RPL-GLA-13114)
Shade(RPL-SHA-13114)
D1
A1
E1
B1
C1
FIG. 1
Ø7"
Back Plate Dimensions
Ø8 3/4"
Ø2 3/4"
Ø3 1/2"
PD-16818,PD-16824,PD-16830168-LED Flush Mount
1Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JANUARY, 2017
modernforms.comPhone (800) 526.2588Fax (800) 526.2585
Headquarters/Eastern Distribution Center44 Harbor Park Drive Port Washington, NY 11050
Central Distribution Center1600 Distribution CtLithia Springs, GA 30122
Western Distribution Center 1750 Archibald Avenue Ontario, CA 91760
Junction Box
Mounting Plate
Canopy
Stem
FixtureShade
PC Diffuser
Glass(RPL-GLA-13114)(RPL-GLA-13120)(RPL-GLA-13126)
Shade(RPL-SHA-16818)(RPL-SHA-16824)(RPL-SHA-16830)
Diffuser(RPL-DIF-13114)(RPL-DIF-13120)(RPL-DIF-13126)
PD-16818 4 3/4"
PD-16824 4 3/4"
PD-16830 4 3/4"
PD
-168
18 4
3/4
"
PD
-168
24 4
3/4
"
PD
-168
30 4
3/4
"
PD
-168
18
2 -1
/2"
PD
-168
24
2 -1
/2"
PD
-168
30
2 -1
/2"
G0 Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
Junction Box
Mounting Plate
Canopy
Stem
FixtureShade
PC Diffuser
Glass(RPL-GLA-13114)(RPL-GLA-13120)(RPL-GLA-13126)
Shade(RPL-SHA-16818)(RPL-SHA-16824)(RPL-SHA-16830)
Diffuser(RPL-DIF-13114)(RPL-DIF-13120)(RPL-DIF-13126)
PD-16818 2-1/2"
PD-16824 2-1/2"
PD-16830 2-1/2"
PD-16818 4 3/4"PD-16824 4 3/4"PD-16830 4 3/4"
3. Remove the mounting screw (C) from the fixture.
5. Choose number of rods suitable for your application.6. Thread the fixture wire through the rods and canopy.7. Connect the canopy, rods and lamp body. Make sure all are tightened.
8. Cut the extra wire. Connect the fixture’s input wires to junction box wires as shown in Fig.2, making sure that all wire connectors (A) are secured. If your outlet box has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
9. Insert the PC diffuser into the fixture shade.
4. Secure the mounting plate to the junction box using junction Box screws(B).The side of the mounting back plate marked “GND” must face out.
MOUNTING THE FIXTURE (Fig. 1)
1. Shut off the power at the circuit breaker and remove existing fixture, including the crossbar.2. Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not lose any small parts necessary for installation.
PREPARATION
CONNECTING THE WIRES (Fig. 2)
COMPLETING THE INSTALLATION (Fig. 1, 2)
10. Secure the fixture onto mounting plate with mounting Screws(C).11. For slope ceiling application, rotate wire at the top of the stem to ensure luminaries is aiming down.
Fixture WiresBlack or Smooth
Fixture WiresWhite or Ribbed
Fixture WiresBare wire(Ground)
House WiresBlack(Hot)
House WiresWhite (Neutral)
House WiresGreen or Bare Copper(Ground)
Fig. 2 Wiring
WS-W81612816-Vanities & Wall Sconce
3
3. Remove the mounting screw (B) from the fixture.
5. Secure the mounting plate to the switch box using the junction box screw (C) The side of the mounting plate marked “GND” must face out.
* Required Driver to be recessed within the junction box.
6. The back plate location for this fixture is adjustable. First loosen both adjust nuts(I) by screw driver. Second adjust the back plate to your desired location. Third, pull and tighten the electrical wire. Forth, secure the back plate by screwing both adjust nuts clockwise. 7. Place the fixture over the mounting plate, and secure it with mounting screw (B) and Silicon Gasket (H).8. To prevent moisture from entering the fixture and causing a short, use clear caulking (i.e. indoor/outdoor silicone sealant) to outline the dotted line enclosed area as shown in Fig 3.
4. Connect the driver (G) input wire to junction box wires as shown in Fig. 3, making sure that all wire connectors (A) are secured. If your outlet box has a green or bare cooper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the switch box.
3. Remove the mounting screw (B) from the fixture.
5. Secure the mounting ring(D) to the switch box using the junction box screw (C). Make sure the two holes (Spacing 2-3/4”) are horizontal as shown in Fig. 2. The side of the mounting plate marked “GND” must face out.
* Required Driver to be recessed within the junction box.
6. Secure the mounting plate and conversion plate (E) to the mounting ring with assembly screw (F).7. The back plate location for this fixture is adjustable. First loosen both adjust nuts(I) by screw driver. Second adjust the back plate to your desired location. Third, pull and tighten the electrical wire. Forth, secure the back plate by screwing both adjust nuts clockwise. Lastly,
4. Connect the driver (G) input wire to junction box wires as shown in Fig. 4, making sure that all wire connectors (A) are secured. If your outlet box has a green or bare cooper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the switch box.
8 Place the fixture over the mounting plate, and secure it with mounting screw (B) and Silicon Gasket (H).9. To prevent moisture from entering the fixture and causing a short, use clear caulking (i.e. indoor/outdoor silicone sealant) to outline the dotted line enclosed area as shown in Fig 3.
10. To prevent moisture from entering the outlet box and causing a short, use clear caulking (i.e. indoor/outdoor silicone sealant) to outline the outside of fixture back plate where it meets the wall. Leave a space at the bottom to allow moisture to escape Fig.5.
MOUNT ON 2”X4”SWITCH BOX (Fig. 1)
1. Shut off the power at the circuit breaker and remove existing fixture, including the crossbar.2. Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
PREPARATION
OR
MOUNT ON 4”x 4”JUNCTION BOX (Fig. 2)
Ø4"
1 3/4"
1 3/8" 4 1/4"
2 3/8"
1 3/8" 1 5/8"
5"
4 1/2"
1 3/8"1 5/8"
Mounting Ring Dimensions7MBC101501
Conversion Plate4MBA121109BA
Back Plate Dimensions7MBC106002
Modern Formswww.modernforms.comPhone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center44 Harbor Park Drive • Port Washington, NY 11050Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center 1750 Archibald Ave • Ontario, CA 91761Phone (800) 526.2588 • Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. DECEMBER, 2016 1
INSTALLATION INSTRUCTIONSABRE- Vanities & Wall SconcesWS-W81619
HARDWARE
A1 B1 C1 D1 E1 F1 G1
Wire ConnectorQty: 3PCS+1Extra7EAC112201P3
Junction Box ScrewQty: 2 pcs + 1 Extra7MPF0415C2#8-32x9/16Stainless Steel
Mounting ScrewQty: 1pc Extra7MPF0412S35/32”-32x1/2Stainless Steel
Waterproof WasherQty: 1pc Extra7TGD060301CL
Conversion PlateQty: 1pc4MBA151110BA
Mounting RingQty: 1pc7MBC101501
Assembly ScrewQty: 2pc + 1Extra7MPF0808C1#8-32x5/16Nickel Plating
WARNINGIMPORTANT: NEVER attempt any work without shutting off the electricity.- Read all instructions before installing.- System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations.- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF” the circuit breaker switch(es) that control the power to the fixture or room that you are working on.- Place the wall switch in the “OFF” position.
CAUTION- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this fixture. CAUTION When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
AVERTISSEMENTIMPORTANT : Coupez l’électricité avant TOUTE manipulation.- Lisez toutes les instructions avant d’installer.- Système est destiné à être installé par un électricien qualifié en conformité avec le code national de l’électricité et les règlements locaux. - Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt (« OFF »). - Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIAIMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico. - Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta lámpara.- Sistema está disenado para ser instalado por un electricista calificado, de acuerdo con el código eléctrico nacional y las normas locales. - Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación principal en la posición “OFF” (APAGADO). - Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calificación ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
Modern Formswww.modernforms.comPhone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center44 Harbor Park Drive • Port Washington, NY 11050Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center 1750 Archibald Ave • Ontario, CA 91761Phone (800) 526.2588 • Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. DECEMBER, 2016 2
Junction BoxFIG. 2 MOUNT ON JUNCTION BOX
C1
D1
B1
F1
E1
G1
A1
B1
Back Plate Dimensions Mounting Ring Dimensions
Mounting Screw
Waterproof Washer
SwitchBox
Driver
Mounting Ring
Junction Box Screw
Mounting Plate
Assembly Screw
Conversion Plate
Input Wires
Wire Connector
Mounting Plate
Junction Box Screw
5 1/2”
2 3/8”1 3/4”
1 3/8”
Ø3 1/4”
Ø4”
Ø2 3/4”
Driver
Fixture
FIG. 1 MOUNT ON SWITCH
INSTALLATION INSTRUCTIONSABRE- Vanities & Wall SconcesWS-W81619
Modern Formswww.modernforms.comPhone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center44 Harbor Park Drive • Port Washington, NY 11050Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center 1750 Archibald Ave • Ontario, CA 91761Phone (800) 526.2588 • Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. DECEMBER, 2016 3
Junction Box
Caulking
Fig. 4 Sealing
PREPARATION 1. Shut off the power at the circuit breaker and remove existing fixture, including the crossbar.2. Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
INSTALLATIONMOUNT ON SWITCH BOX (Fig. 1) 3. Remove the mounting screw (C1) and waterproof washer (D1) from the fixture.4. Connect the driver input/output wire to supply wires as shown in Fig. 3, making sure that all wire connectors (A1) are secured. If your outlet
box has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the switch box.
5. Secure the mounting plate to the switch box using the junction box screw (B1). The side of the mounting plate marked “GND” must face out.6. Place the fixture over the mounting back plate, and secure it with mounting screw (C1) and water proof washer (D1).7. To prevent moisture from entering the outlet box and causing a short, use clear caulking (i.e. indoor/outdoor silicone sealant) to outline the
outside of fixture back plate where it meets the wall. Leave a space at the bottom to allow moisture to escape Fig. 4.
OR
MOUNT ON JUNCTION BOX (Fig. 2)3. Remove the mounting screw (C1) and waterproof washer (D1) from the fixture.4. Connect the driver input/output wire to supply wires as shown in Fig. 3, making sure that all wire connectors (A1) are secured. If your outlet
box has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
5. Secure the mounting ring (D1) to the junction box using the junction box screw (B1). Make sure the two holes (spacing 2-3/4”) are horizontal as shown in Fig 2. The side of the mounting plate marked “GND” must face out.
6. Place the mounting plate and the conversion plate (E1) onto the mounting ring (F1), secure them with assembly screw (G1).7. Place the fixture over the mounting back plate, and secure it with mounting screw (C1) and water proof washer (D1).8. To prevent moisture from entering the outlet box and causing a short, use clear caulking (i.e. indoor/outdoor silicone sealant) to outline the
outside of fixture back plate where it meets the wall. Leave a space at the bottom to allow moisture to escape Fig. 4.
INSTALLATION INSTRUCTIONSABRE- Vanities & Wall SconcesWS-W81619
Fixture WiresBlack or Smooth
Fixture WiresWhite or Ribbed
Fixture WiresBare wire(Ground)
House WiresBlack(Hot)
House WiresWhite (Neutral)
House WiresGreen or Bare Copper(Ground)
Fig.2 Wiring
Modern Formswww.modernforms.comPhone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center44 Harbor Park Drive • Port Washington, NY 11050Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center 1750 Archibald Ave • Ontario, CA 91761Phone (800) 526.2588 • Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. DECEMBER, 2016 4
INSTALLATION INSTRUCTIONSABRE- Vanities & Wall SconcesWS-W81625/WS-W81637
HARDWARE
A1 B1 C1 D1 E1 F1 G1
Wire ConnectorQty: 3PCS+1Extra7EAC112201P3
Junction Box ScrewQty: 2 pcs + 1 Extra7MPF0415C2#8-32x9/16Stainless Steel
Mounting ScrewQty: 1pc Extra7MPF0412S35/32”-32x1/2Stainless Steel
Waterproof WasherQty: 1pc Extra7TGD060301CL
Conversion PlateQty: 1pc4MBA151110BA
Mounting RingQty: 1pc7MBC101501
Assembly ScrewQty: 2pc + 1Extra7MPF0808C1#8-32x5/16Nickel Plating
WARNINGIMPORTANT: NEVER attempt any work without shutting off the electricity.- Read all instructions before installing.- System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations.- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF” the circuit breaker switch(es) that control the power to the fixture or room that you are working on.- Place the wall switch in the “OFF” position.
CAUTION- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this fixture. CAUTION When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
AVERTISSEMENTIMPORTANT : Coupez l’électricité avant TOUTE manipulation.- Lisez toutes les instructions avant d’installer.- Système est destiné à être installé par un électricien qualifié en conformité avec le code national de l’électricité et les règlements locaux. - Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt (« OFF »). - Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIAIMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico. - Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta lámpara.- Sistema está disenado para ser instalado por un electricista calificado, de acuerdo con el código eléctrico nacional y las normas locales. - Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación principal en la posición “OFF” (APAGADO). - Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calificación ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
Modern Formswww.modernforms.comPhone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center44 Harbor Park Drive • Port Washington, NY 11050Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center 1750 Archibald Ave • Ontario, CA 91761Phone (800) 526.2588 • Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. DECEMBER, 2016 5
Assembly Screw
Junction BoxFIG. 2 MOUNT ON JUNCTION BOX
C1
D1
B1
F1
E1
G1
A1
B1
Back Plate Dimensions Mounting Ring Dimensions
Mounting Screw
Waterproof Washer
SwitchBox
Driver
Mounting Ring
Junction Box Screw
Mounting Plate
Conversion Plate
Input Wires
Wire Connector
Mounting Plate
Junction Box Screw
5 7/8”
2 1/2” 1 3/4”
1 3/8”
Ø3 1/4”
Ø4”
Ø2 3/4”
Driver
Fixture
FIG. 1 MOUNT ON SWITCH
INSTALLATION INSTRUCTIONSABRE- Vanities & Wall SconcesWS-W81625/WS-W81637
Modern Formswww.modernforms.comPhone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center44 Harbor Park Drive • Port Washington, NY 11050Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center 1750 Archibald Ave • Ontario, CA 91761Phone (800) 526.2588 • Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. DECEMBER, 2016 6
Junction Box
Caulking
Fig. 4 Sealing
PREPARATION 1. Shut off the power at the circuit breaker and remove existing fixture, including the crossbar.2. Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
INSTALLATIONMOUNT ON SWITCH BOX (Fig. 1) 3. Remove the mounting screw (C1) and waterproof washer (D1) from the fixture.4. Connect the driver input/output wire to supply wires as shown in Fig. 3, making sure that all wire connectors (A1) are secured. If your outlet
box has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the switch box.
5. Secure the mounting plate to the switch box using the junction box screw (B1). The side of the mounting plate marked “GND” must face out.6. Place the fixture over the mounting back plate, and secure it with mounting screw (C1) and water proof washer (D1).7. To prevent moisture from entering the outlet box and causing a short, use clear caulking (i.e. indoor/outdoor silicone sealant) to outline the
outside of fixture back plate where it meets the wall. Leave a space at the bottom to allow moisture to escape Fig. 4.
OR
MOUNT ON JUNCTION BOX (Fig. 2)3. Remove the mounting screw (C1) and waterproof washer (D1) from the fixture.4. Connect the driver input/output wire to supply wires as shown in Fig. 3, making sure that all wire connectors (A1) are secured. If your outlet
box has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
5. Secure the mounting ring (D1) to the junction box using the junction box screw (B1). Make sure the two holes (spacing 2-3/4”) are horizontal as shown in Fig 2. The side of the mounting plate marked “GND” must face out.
6. Place the mounting plate and the conversion plate (E1) onto the mounting ring (F1), secure them with assembly screw (G1).7. Place the fixture over the mounting back plate, and secure it with mounting screw (C1) and water proof washer (D1).8. To prevent moisture from entering the outlet box and causing a short, use clear caulking (i.e. indoor/outdoor silicone sealant) to outline the
outside of fixture back plate where it meets the wall. Leave a space at the bottom to allow moisture to escape Fig. 4.
INSTALLATION INSTRUCTIONSabre- Vanities & Wall SconcesWS-W81625/WS-W81637
Fixture WiresBlack or Smooth
Fixture WiresWhite or Ribbed
Fixture WiresBare wire(Ground)
House WiresBlack(Hot)
House WiresWhite (Neutral)
House WiresGreen or Bare Copper(Ground)
Fig.2 Wiring