INSTALLATION INSTRUCTION 776 - Vanities & Wall Sconce WS ... · - Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta

1WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. 10/09/15

waclighting.comPhone (800) 526.2588Fax (800) 526.2585

Headquarters/Eastern Distribution Center44 Harbor Park Drive Port Washington, NY 11050

Central Distribution Center1600 Distribution CtLithia Springs, GA 30122

Western Distribution Center 1750 Archibald Avenue Ontario, CA 91760

HARDWARE

WARNINGIMPORTANT: NEVER attempt any work without shutting o� the electricity.- Read all instructions before installing.- System is intended for installation by a quali�ed electrician in accordance with the National Electrical Code and local regulations.- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF” the circuit breaker switch(es) that control the power to the �xture or room that you are working on.- Place the wall switch in the “OFF” position.

CAUTION- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this �xture. CAUTION When handling the �xture, do not apply pressure to the LEDs. Hold the �xture by the base only.

AVERTISSEMENTIMPORTANT : Coupez l’électricité avant TOUTE manipulation.- Lisez toutes les instructions avant d’installer.- Système est destiné à être installé par un électricien quali�é en conformité avec le code national de l’électricité et les règlements locaux. - Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt (« OFF »). - Placez l’interrupteur mural en position d’arrêt (« OFF »).

MISE EN GARDE- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.

ADVERTENCIAIMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico. - Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta lámpara.- Sistema está disenado para ser instalado por un electricista cali�cado, de acuerdo con el código eléctrico nacional y las normas locales. - Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación principal en la posición “OFF” (APAGADO). - Coloque el interruptor de la pared en la posición “OFF” (APAGADO).

PRECAUCIÓN- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la cali�cación ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.

INSTALLATION INSTRUCTION776 - Vanities & Wall SconceWS-7761

Wire ConnectorQty: 5 pcs

DriverQty: 1 pc

Assembly ScrewQty: 2 pcs + 1 Extra

Conversion PlateQty: 1 pc

Mounting RingQty: 1 pc

Junction Box ScrewQty: 2 pcs + 1 Extra

Mounting ScrewQty: 1 Extra

A GFEDCBA B C D E F G

Wire ConnectorQty:5pcs+1Extra

7EAC112201P3

Mounting ScrewQty:1Extra

7MPF0409S35/32”-32x3/8

Nickel

Junction Box ScrewQty:2pcs+1Extra

7MPF0808C1#8-32x5/16

Nickel

Assembly ScrewQty:2pcs+1Extra

7MPF0415C2 4LD-700MA U-IS-P#8-32x9/16

Stainless steel

DriverQty:1pc

Conversion PlateQty:1pc

4MBA1 BABrushed Alum

Mounting RingQty:1pc

7MBC101501

WireConnectorQty: 3pcs+1Extra 7EAC112201 P3

Mounting Screw Qty:1 Extra 7MPF0412S1(AL) 4MPF0412S2SB(BR) 5/32"-32x1/2Nickel Plating / Brass Plating

Junction Box Screw Qty: 2+1 Extra 7MPF0808C1 #8-32x5/16 Nickel

Conversion Plate Qty:1 pc4MBA121109BA : WS-77612(AL)4MBC121112SB : WS-77612(BR)4MBA151110BA : WS-77618(AL)4MBC151110SB : WS-77618(BR)4MBA171110BA : WS-77624(AL)4MBC171111SB : WS-77624(BR)4MBA201104BA : WS-77636(AL)4MBC201105SB : WS-77636(BR) Brushed Alum / Brass Plating

AssemblyScrew Qty:2+1 Extra 7MPF0415C2 #8-32x9/16Stainless steel

Mounting Ring Qty:1 pc7MBC101501

Driver Qty:1 pc4LD-700MA16U-IS-P(WS-77612)4LD-700MA28U-IS-P(WS-77618)4LD-700MA28U-IS-P(WS-77624)4LD-700MA28U-IS-P(WS-77636)

A B C D E F G

WS-77612/ WS-77618/ WS-77624/ WS-77636






HARDWARE









DriverQty: 1 pc








7EAC112201P3


7MPF0409S35/32”-32x3/8

Nickel


7MPF0808C1#8-32x5/16

Nickel


7MPF0415C2 4LD-700MA U-IS-P#8-32x9/16

Stainless steel

DriverQty:1pc




7MBC101501

G2







FIG. 1 MOUNT ON SWITCH

FIG. 2 MOUNT ON JUNCTION BOX

FIG. 3

CJunction Box Screw

Wire

Adjustable Nut

B

G

A

F E

B

C

D

G

Mounting Screw

Fixture

Driver

Wire Connector

Assembly ScrewConversion Plate

Mounting Screw

5 1/2”

2 3/8”

1 5/8”1 3/8”

Adjustable Nut

Fixture Backplate

Junction Box Screw

Mounting Ring

Driver

Junction Box

Mounting Plate

Switch Box

Mounting Plate

Back Plate Dimensions

B

G

A

C

Mounting Screw

Switch Box

Driver 2 3/4" to 3 3/8"Lx1 1/4"W x1 1/8"H

Fixture

Wire Connector

Mounting Plate

Junction Box Screw

Adjust Nut

Female/Male end connector

WS-77612 / WS-77618

WS-77624 / WS-77636

FIG.2 MOUNT ON JUNCTION BOX

B Mounting Screw

Adjust Nut

Wire

Fixture Backplate

WS-77624 / WS-77636 WS-77612 / WS-77618

WS-77612/ WS-77618/ WS-77624/ WS-77636






HARDWARE









DriverQty: 1 pc








7EAC112201P3


7MPF0409S35/32”-32x3/8

Nickel


7MPF0808C1#8-32x5/16

Nickel


7MPF0415C2 4LD-700MA U-IS-P#8-32x9/16

Stainless steel

DriverQty:1pc




7MBC101501






HARDWARE









DriverQty: 1 pc








7EAC112201P3


7MPF0409S35/32”-32x3/8

Nickel


7MPF0808C1#8-32x5/16

Nickel


7MPF0415C2 4LD-700MA U-IS-P#8-32x9/16

Stainless steel

DriverQty:1pc




7MBC101501

G2







PREPARATION 1. Shut o� the power at the circuit breaker and remove existing �xture, including the crossbar.2. Carefully unpack your new �xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.

INSTALLATIONMOUNT ON SWITCH BOX (Fig. 1) 3. Remove the mounting screw (B) from the �xture.4. Connect the driver (G) input wire to switch box wires as shown in Fig. 4, making sure that all wire connectors (A) are secured.

If your outlet box has a green or bare cooper ground wire, connect the �xture’s ground wire to it. Otherwise, connect the �xture’s ground wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the switch box. *Requires Driver to be recessed within the switch box.

5. Secure the mounting plate to the switch box using the junction box screw (C). The side of the mounting plate marked “GND” must face out.6. The back plate location for this �xture is adjustable. First loosen both adjustable nuts by turning counterclockwise. Second adjust the

back plate to your desired location. Third, pull and tighten the electrical wire. Lastly, secure the back plate by turning both adjustable nuts clockwise.

7. Place the �xture over the mounting plate, and secure it with mounting screw (B).

OR

MOUNT ON JUNCTION BOX (Fig. 2)3. Remove the mounting screw (B) from the �xture.4. Connect the driver (G) input wire to junction box wires as shown in Fig. 4, making sure that all wire connectors (A) are secured.

If your outlet box has a green or bare cooper ground wire, connect the �xture’s ground wire to it. Otherwise, connect the �xture’s ground wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the switch box. *Requires driver to be recessed within the junction box.

5. Secure the mounting ring to the junction box using the junction box screw (C). Make sure the two holes (Spacing 2-3/4”) are horizontal as shown in Fig. 2. The side of the mounting plate marked “GND” must face out.

6. Secure the mounting plate and conversion plate (E) to the mounting ring with assembly screw (F).7. The back plate location for this �xture is adjustable. First loosen both adjustable nuts by turning counterclockwise. Second adjust the



Fixture WiresBlack or Smooth

Fixture WiresWhite or Ribbed

Fixture WiresBare wire(Ground)

House WiresBlack(Hot)

House WiresWhite (Neutral)

House WiresGreen or Bare Copper(Ground)

Fig. 4 WiringBack Plate Dimensions Mounting Ring Dimensions

Ø4"

1 3/4"

1 3/8"

GND

4 1/4"

2 3/8"

1 3/8" 1 5/8"

Back Plate Dimensions Mounting Ring Dimensions

Ø4"

1 3/4"

1 3/8"

GND

4 1/4"

2 3/8"

1 3/8" 1 5/8"

5"

4 1/2"

1 3/8"1 5/8"


Ø4"

1 3/4"

1 3/8"

GND

4 1/4"

2 3/8"

1 3/8" 1 5/8"


Conversion PlateMounting Ring Dimensions

FE

C

D

G

Junction Box

Mounting Ring

Driver 2 3/4" to 3 3/8"Lx1 1/4"W x1 1/8"H

Junction Box Screw

Conversion PlateMounting Plate

Assembly Screw

FIG.3

WS-77612/ WS-77618/ WS-77624/ WS-77636

3. Remove the mounting screw (B) from the �xture.

4. Connect the driver (G) input wire to switch box wires as shown in Fig. 4, making sure that all wire connectors (A) are secured. If your outlet box has a green or bare cooper ground wire, connect the �xture’s ground wire to it. Otherwise, connect the �xture’s ground wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the switch box.

5. Secure the mounting plate to the switch box using the junction box screw (C). The side of the mounting plate marked “GND” must face out. tuck them carefully inside the junction box.

6. The back plate location for this �xture is adjustable. First loosen both adjustable nuts by turning counterclockwise. Second adjust the back plate to your desired location. Third, pull and tighten the electrical wire. Lastly, secure the back plate by turning both adjustable nuts clockwise.

7. Connect the driver(G)output wires to the �xture by Female/Male end connector as shown in Fig1


MOUNT ON SWITCH BOX (Fig. 1)

* Requires Driver to be recessed within the switch box. the hole mounting extensions on the driver are trimmable/foldable for tighter junction box fitment.

1. Shut o� the power at the circuit breaker and remove existing �xture, including the crossbar.2. Carefully unpack your new �xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.

PREPARATION

3. Remove the mounting screw (B) from the �xture.

MOUNT ON JUNCTION BOX (Fig. 2)

OR






HARDWARE









DriverQty: 1 pc








7EAC112201P3


7MPF0409S35/32”-32x3/8

Nickel


7MPF0808C1#8-32x5/16

Nickel


7MPF0415C2 4LD-700MA U-IS-P#8-32x9/16

Stainless steel

DriverQty:1pc




7MBC101501

G2







PREPARATION 1. Shut o� the power at the circuit breaker and remove existing �xture, including the crossbar.2. Carefully unpack your new �xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.

INSTALLATIONMOUNT ON SWITCH BOX (Fig. 1) 3. Remove the mounting screw (B) from the �xture.4. Connect the driver (G) input wire to switch box wires as shown in Fig. 4, making sure that all wire connectors (A) are secured.

If your outlet box has a green or bare cooper ground wire, connect the �xture’s ground wire to it. Otherwise, connect the �xture’s ground wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the switch box. *Requires Driver to be recessed within the switch box.

5. Secure the mounting plate to the switch box using the junction box screw (C). The side of the mounting plate marked “GND” must face out.6. The back plate location for this �xture is adjustable. First loosen both adjustable nuts by turning counterclockwise. Second adjust the



OR

MOUNT ON JUNCTION BOX (Fig. 2)3. Remove the mounting screw (B) from the �xture.4. Connect the driver (G) input wire to junction box wires as shown in Fig. 4, making sure that all wire connectors (A) are secured.

If your outlet box has a green or bare cooper ground wire, connect the �xture’s ground wire to it. Otherwise, connect the �xture’s ground wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the switch box. *Requires driver to be recessed within the junction box.


6. Secure the mounting plate and conversion plate (E) to the mounting ring with assembly screw (F).7. The back plate location for this �xture is adjustable. First loosen both adjustable nuts by turning counterclockwise. Second adjust the









Fig. 4 WiringBack Plate Dimensions Mounting Ring Dimensions

Ø4"

1 3/4"

1 3/8"

GND

4 1/4"

2 3/8"

1 3/8" 1 5/8"


Ø4"

1 3/4"

1 3/8"

GND

4 1/4"

2 3/8"

1 3/8" 1 5/8"

5"

4 1/2"

1 3/8"1 5/8"


Ø4"

1 3/4"

1 3/8"

GND

4 1/4"

2 3/8"

1 3/8" 1 5/8"


Conversion PlateMounting Ring Dimensions

WS-77612/ WS-77618/ WS-77624/ WS-77636

4

Back Plate Dimensions7MBC156402:WS-77624 / WS-77636

Mounting Ring Dimensions

7MBC101501

Ø4"

1 3/4"

1 3/8"

GND

4 1/2"

1 3/8"1 5/8"

Conversion Plate

2 1/2"

1 3/8"1 5/8"

5 7/8"


WS-77612 : 7MBC106002

WS-77618 : 7MBC116501

2 3/8"

1 3/8" 1 5/8"

WS-77612 5”WS-77618 6”WS-77624 7”WS-77636 8”

WS-77612 4 1/4”WS-77618 5 1/2”







Fig.4 Wiring

4. Connect the driver (G) input wire to junction box wires as shown in Fig. 4, making sure that all wire connectors (A) are secured. If your outlet box has a green or bare cooper ground wire, connect the �xture’s ground wire to it. Otherwise, connect the �xture’s ground wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the switch box.


6. Secure the mounting plate and conversion plate (E) to the mounting ring with assembly screw (F).

7. The back plate location for this �xture is adjustable. First loosen both adjustable nuts by turning counterclockwise. Second adjust the back plate to your desired location. Third, pull and tighten the electrical wire. Lastly, secure the back plate by turning both adjustable nuts clockwise.

8. Connect the driver(G)output wires to the �xture by Female/Male end connector as shown in Fig2.


* Requires driver to be recessed within the junction box. the hole mounting extensions on the driver are trimmable/foldable for tighter junction box fitment.






HARDWARE









DriverQty: 1 pc








7EAC112201P3


7MPF0409S35/32”-32x3/8

Nickel


7MPF0808C1#8-32x5/16

Nickel


7MPF0415C2 4LD-700MA U-IS-P#8-32x9/16

Stainless steel

DriverQty:1pc




7MBC101501






HARDWARE









DriverQty: 1 pc








7EAC112201P3


7MPF0409S35/32”-32x3/8

Nickel


7MPF0808C1#8-32x5/16

Nickel


7MPF0415C2 4LD-700MA U-IS-P#8-32x9/16

Stainless steel

DriverQty:1pc




7MBC101501

G2

Documents

INSTALLATION INSTRUCTION 776 - Vanities & Wall Sconce WS ... · - Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta