INSTALLATION INSTRUCTION 486 - LED Outdoor …...- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch

1WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program.

waclighting.comPhone (800) 526.2588Fax (800) 526.2585

Headquarters/Eastern Distribution Center44 Harbor Park Drive Port Washington, NY 11050

Central Distribution Center1600 Distribution CtLithia Springs, GA 30122

Western Distribution Center 1750 Archibald Avenue Ontario, CA 91760

INSTALLATION INSTRUCTION486 - LED OutdoorWS-W48612, WS-W48616, WS-W48620

WARNINGIMPORTANT: NEVER attempt any work without shutting off the electricity.- Read all instructions before installing.- System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations.- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF” the circuit breaker switch(es) that control the power to the fixture or room that you are working on.- Place the wall switch in the “OFF” position.

CAUTION- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this fixture. CAUTION When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.

AVERTISSEMENTIMPORTANT : Coupez l’électricité avant TOUTE manipulation.- Lisez toutes les instructions avant d’installer.- Système est destiné à être installé par un électricien qualifié en conformité avec le code national de l’électricité et les règlements locaux. - Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt (« OFF »). - Placez l’interrupteur mural en position d’arrêt (« OFF »).

MISE EN GARDE- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.

ADVERTENCIAIMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico. - Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta lámpara.- Sistema está disenado para ser instalado por un electricista calificado, de acuerdo con el código eléctrico nacional y las normas locales. - Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación principal en la posición “OFF” (APAGADO). - Coloque el interruptor de la pared en la posición “OFF” (APAGADO).

PRECAUCIÓN- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calificación ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.

HARDWARE

Wire ConnectorQty: 3 pcs +1 Extra

7EAC112201

Rubber GasketQty: 1 Extra

7TGD060301CL

Mounting ScrewQty: 1 Extra

4MPF0412S2BW

Junction Box ScrewQty: 2 pcs + 1 Extra

7MPF0415C2

A1 D1C1B1






INSTALLATION INSTRUCTION486 - LED OutdoorWS-W48612, WS-W48616, WS-W48620

FIG.1

Junction Box Screw

Mounting Screw

Rubber Gasket

Junction Box

Ground Wire

Mounting Back Plate

Wire Connector

Back Plate Dimensions

White Wire

Black Wire

B1

C1

D1

A1

Fixture WiresBlack or Smooth

Fixture WiresWhite or Ribbed

Fixture WiresBare wire(Ground)

House WiresBlack(Hot)

House WiresWhite (Neutral)

House WiresGreen or Bare Copper(Ground)

Fig. 2 Wiring

Junction Box

Caulking

Fig.3 Sealing

PREPARATION 1. Shut off the power at the circuit breaker and remove existing fixture, including the crossbar.2. Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.

MOUNTING THE FIXTURE (Fig. 1)3. Remove the mounting screw (C1) and the rubber gasket (D1) from the mounting back plate.4. Secure the mounting back plate to the junction box using junction box screws (B1). The side of the mounting back plate marked “GND”

must face out.

CONNECTING THE WIRES (Fig. 2)5. Connect the fixture’s wires to junction box wires as shown in Fig. 2, making sure that all wire connectors (A1) are secured. If your outlet box

has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.

COMPLETING THE INSTALLATION (Fig. 1)6. Secure the fixture to the mounting back plate using the mounting screw (C1) and the rubber gasket (D1).7. To prevent moisture from entering the outlet box and causing a short, use clear caulking (i.e. indoor/outdoor silicone sealant) to outline the

outside of fixture back plate where it meets the wall. Leave a space at the bottom to allow moisture to escape Fig. 3.

WS-W48612 5 3/4"WS-W48616 7 5/8"WS-W48620 9 1/4"

1 3/8"

1 3/4"

WS-W48612 4 1/8"WS-W48616 5 1/8"WS-W48620 5 5/8"





WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program.

INSTALLATION INSTRUCTION758 – LED Wall SconceWS-75818

HARDWARE

A B C D E

Wire ConnectorQty: 3pcs+1 Extra7EAC112201

Junction Box ScrewQty: 2pcs+1 Extra7MPF0820C1#8-32x13/16Nickel Plating

Wood Screw Qty: 2pcs+1 Extra7MPF2204J2Ф4X22

Plastic Anchor Qty: 2pcs+1 Extra7TDD082401

Mounting ScrewQty: 1 Extra7MPF0412S1(AL)5/32-32x1/2Nickel Plating

WARNINGIMPORTANT: NEVER attempt any work without shutting o� the electricity.- Read all instructions before installing.- System is intended for installation by a quali�ed electrician in accordance with the National Electrical Code and local regulations.- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF” the circuit breaker switch(es) that control the power to the �xture or room that you are working on.- Place the wall switch in the “OFF” position.

CAUTION- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this �xture. CAUTION When handling the �xture, do not apply pressure to the LEDs. Hold the �xture by the base only.

AVERTISSEMENTIMPORTANT : Coupez l’électricité avant TOUTE manipulation.- Lisez toutes les instructions avant d’installer.- Système est destiné à être installé par un électricien quali�é en conformité avec le code national de l’électricité et les règlements locaux. - Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt (« OFF »). - Placez l’interrupteur mural en position d’arrêt (« OFF »).


ADVERTENCIAIMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico. - Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta lámpara.- Sistema está disenado para ser instalado por un electricista cali�cado, de acuerdo con el código eléctrico nacional y las normas locales. - Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación principal en la posición “OFF” (APAGADO). - Coloque el interruptor de la pared en la posición “OFF” (APAGADO).

PRECAUCIÓN- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la cali�cación ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.

PD-87741877-LED Pendant







HARDWARE

A B C D E












G0

ScrewQty:1 Extra

1/8"-40×1/2 Chrome Plating

Optional Metal CapQty:1 Extra

Chrome Plating

Wire ConnectorQty: 3pcs+1 Extra

P3

Junction Box ScrewQty: 2pcs+1 Extra

8#-32×13/16Nickel Plating

Mounting ScrewQty:1 Extra

5/32"-32×1/2Chrome Plating

A D EB C


Wire Connector

Qty: 3pcs+1 Extra

P3

Junction Box Screw

Qty: 2pcs+1 Extra

8#-32×13/16

Nickel Plating

Mounting Screw

Qty:1 Extra

5/32"-32×1/2

Chrome Plating

A B C

WS-W48625/ WS-W48625F486 – LED Outdoor

Wire ConnectorQty: 3pcs+1 Extra

Mounting ScrewQty:1 Extra

Rubber GasketQty:1 Extra

A B C

Plastic AnchorQty:2pcs+1 Extra

D

Wood ScrewQty: 2pcs+1 Extra

E







PREPARATION 1. Shut o� the power at the circuit breaker and remove existing �xture, including the crossbar.2. Carefully unpack your new �xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for

installation.

MOUNTING THE FIXTURE (Fig. 1)3. Remove the mounting screw (E) from the mounting back plate.4. Drill holes in the wall aligned with the key holes located in the mounting back plate, insert the plastic anchors (D).5. Secure the mounting plate to the junction box using junction box screws (B), fasten it to the wall using wood screws (C). The side of

the mounting back plate marked “GND” must face out.

CONNECTING THE WIRES (Fig. 2)6. Connect the driver input/output wires to junction box wires as shown in

Fig. 2, making sure that all wire connectors (A) are secured. If your outlet box has a green or bare copper ground wire, connect the �xture’s ground wire to it. Otherwise, connect the �xture’s ground wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box. * Requires Driver to be recessed within the junction box.

COMPLETING THE INSTALLATION (Fig. 1)7. Secure the �xture to the mounting back plate using the mounting screw (E).

4 1/8”

15”11 3/4”

1 3/8”

1 3/4”

WS-75818MOUNTING BACK PLATE







Fig.2 Wiring

FIG.1 Junction Box Screw

Junction Box

Wire Connector

Driver

Plastic Anchor

Mounting Plate

Wood Screw

Mounting Screw

B

A

D

C

E








HARDWARE

A B C D E












G0

Plate

Ground Wire Screw

3 3/8" L X 2 3/8" W X 1 1/4" H Driver

Plastic

D

C

B

A






INSTALLATION INSTRUCTION131 - LED Flush MountFM-13114

PREPARATION 1. Shut o� the power at the circuit breaker and remove existing �xture, including the crossbar.2. Carefully unpack your new �xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.

CONNECTING THE WIRES (Fig. 2)3. Remove the mounting screws (C1) from �xture. 4. Drill holes in the ceiling aligned with the key holes located in the mounting plate, insert the plastic anchors (D1).5. Connect the �xture’s input wires to junction box wires as shown in Fig. 2, making sure that all wire connectors (A1) are secured.

If your outlet box has a green or bare copper ground wire, connect the �xture’s ground wire to it. Otherwise, connect the �xture’s ground wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.

MOUNTING THE FIXTURE (Fig. 1)6. Secure the mounting plate to the junction box using junction box screws (B1),

fasten it to the wall using wood screw (E1). The side of the mounting back plate marked “GND” must face out.

7. Insert the PC di�user into the �xture shade.8. Secure the �xture onto mounting plate with mounting screws (C1).







Fig. 2 Wiring

Plastic Anchor

Wire Connector

Wood Screw

Junction Box Screw

Mounting Screw

Fixture Shade

PC Di�user

Mounting Plate

Junction Box

Glass(RPL-GLA-13114)

Shade(RPL-SHA-13114)

D1

A1

E1

B1

C1

FIG. 1

Ø7"


GND

Ø8 3/4"

Ø2 3/4"

Ø3 1/2"

FM-16818168-LED Flush Mount

1Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JANUARY, 2017

modernforms.comPhone (800) 526.2588Fax (800) 526.2585




HARDWARE







INSTALLATION INSTRUCTIONSlat - Vanities & Wall SconcesWS-80618/WS-80624/WS-80636

Wire ConnectorQty: 3 pcs

7EAC112201

MountingRing

Qty: 1 pc7MBC101501

Transformer

Qty: 1 pc5EN-2460-R2

JunctionBox ScrewQty: 2 pcs+ 1 Extra

7MPF0825C18-32x1 SS

ConversionPlate

Qty: 1 pc4MBA151110BA

MountingScrew

Qty: 2 pcs+ 1 Extra

7MPF0415C28-32x9/16 SS

SetScrew

Qty: 2 Extra7MPF0308S15/32-32x5/16Nickel Plating

MountingAnchor

Qty: 2 pcs7TDD082401

TappingScrew

Qty: 2 pcs7MPF2204J2

Ø4x22

A1 B1 C1 D1 E1 F1 G1 H1 I1

Junction Box

Mounting Plate

Fixture Shade

PC Diffuser

Wire Connector

Plastic Anchor

Wood Screw

Junction Box Screw

Mounting Screw Glass(RPL-GLA-13114)


Diffuser(RPL-DIF-13114)

G0 1Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JANUARY, 2017





HARDWARE









7EAC112201

MountingRing

Qty: 1 pc7MBC101501

Transformer



7MPF0825C18-32x1 SS

ConversionPlate


MountingScrew

Qty: 2 pcs+ 1 Extra

7MPF0415C28-32x9/16 SS

SetScrew


MountingAnchor


TappingScrew


Ø4x22

A1 B1 C1 D1 E1 F1 G1 H1 I1

( C )

( C )

( E )

( D )

( B )

( A )

3. Remove the mounting screw (C) from the fixture.

5. Secure the mounting back plate to the junction box using junction box screws (B).The side of the mounting back plate marked “GND” must face out.

6. Secure the canopy to the mounting plate using the mounting screw (C).

4. Connect the Driver’s input wires to junction box wires as shown in Fig. 2, making sure that all wire connectors (A) are secured. If your outlet box has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.

CONNECTING THE WIRES (Fig. 2)

1. Shut off the power at the circuit breaker and remove existing fixture, including the crossbar.2. Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not lose any small parts necessary for installation.

PREPARATION

MOUNTING THE FIXTURE(Fig.1)

7. There is optional metal clip in hardware bag, remove the screw (D) to replace the plastic clip, secure the metal clip with screw (D).







Fig.2 Wiring







INSTALLATION INSTRUCTION131 - LED Flush MountFM-13114

PREPARATION 1. Shut o� the power at the circuit breaker and remove existing �xture, including the crossbar.2. Carefully unpack your new �xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.

CONNECTING THE WIRES (Fig. 2)3. Remove the mounting screws (C1) from �xture. 4. Drill holes in the ceiling aligned with the key holes located in the mounting plate, insert the plastic anchors (D1).5. Connect the �xture’s input wires to junction box wires as shown in Fig. 2, making sure that all wire connectors (A1) are secured.

If your outlet box has a green or bare copper ground wire, connect the �xture’s ground wire to it. Otherwise, connect the �xture’s ground wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.

MOUNTING THE FIXTURE (Fig. 1)6. Secure the mounting plate to the junction box using junction box screws (B1),

fasten it to the wall using wood screw (E1). The side of the mounting back plate marked “GND” must face out.

7. Insert the PC di�user into the �xture shade.8. Secure the �xture onto mounting plate with mounting screws (C1).







Fig. 2 Wiring

Plastic Anchor

Wire Connector

Wood Screw

Junction Box Screw

Mounting Screw

Fixture Shade

PC Di�user

Mounting Plate

Junction Box

Glass(RPL-GLA-13114)


D1

A1

E1

B1

C1

FIG. 1

Ø7"


GND

Ø8 3/4"

Ø2 3/4"

Ø3 1/2"

FM-16818168-LED Flush Mount

1Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JANUARY, 2017





HARDWARE









7EAC112201

MountingRing

Qty: 1 pc7MBC101501

Transformer



7MPF0825C18-32x1 SS

ConversionPlate


MountingScrew

Qty: 2 pcs+ 1 Extra

7MPF0415C28-32x9/16 SS

SetScrew


MountingAnchor


TappingScrew


Ø4x22

A1 B1 C1 D1 E1 F1 G1 H1 I1

Junction Box

Mounting Plate

Fixture Shade

PC Diffuser

Wire Connector

Plastic Anchor

Wood Screw

Junction Box Screw

Mounting Screw Glass(RPL-GLA-13114)


Diffuser(RPL-DIF-13114)

G0 1Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JANUARY, 2017





HARDWARE









7EAC112201

MountingRing

Qty: 1 pc7MBC101501

Transformer



7MPF0825C18-32x1 SS

ConversionPlate


MountingScrew

Qty: 2 pcs+ 1 Extra

7MPF0415C28-32x9/16 SS

SetScrew


MountingAnchor


TappingScrew


Ø4x22

A1 B1 C1 D1 E1 F1 G1 H1 I1

( C )

( C )

( E )

( D )

( B )

( A )

10 5

/16"

1 3/4"

1 3/

8"

3. Remove the mounting screw (C) from the canopy.

6. Secure the mounting back plate to the junction box using junction box screws (B).The side of the mounting back plate marked “GND” must face out.

4. Adjust the fixture wire length by pushing the cable gripper on the canopy and pulling the wire as desired. Make sure the wires are the same length.5. Connect the Driver’s input wires to junction box wires as shown in Fig. 2, making sure that all wire connectors (A) are secured. If your outlet box has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.


1. Shut off the power at the circuit breaker and remove existing fixture, including the crossbar.2. Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not lose any small parts necessary for installation.

PREPARATION

MOUNTING THE FIXTURE(Fig.1)







Fig.2 Wiring

Ground Wire Screw

Plate

C

B

A

3 3/8" L X 2 3/8" W X 1 1/4" H Driver

7. Hook the safety cord to the mounting plate.

8. Secure the canopy to the mounting plate using the mounting screw (C).

WS-W48625/ WS-W48625F486 – LED Outdoor

Fig.1 Back Plate Dimensions







Fig.2 Wiring Wood Screw

Mounting Screw

Junction Box ScrewSafety Cords

Ground Wire

Junction Box

Black WireWhite Wire Plastic AnchorD

E

B

Mounting Backplate

Wire ConnectorA

Rubber GasketC

4. Drill holes in the wall aligned with the key holes located on the back plate, insert the plastic anchor (D).5. Secure the mounting back plate to the junction box using standard junction box screws that comes with the junction box. Fasten the back plate to the wall with the plastic anchors using the wood screws(E) provided.

3. Remove the mounting screw (B) and gasket (C) from the �xture, and safety cords from the mounting back plate.

MOUNTING THE FIXTURE (Fig. 1)

COMPLETING THE INSTALLATION


1. Shut o� the power at the circuit breaker and remove existing �xture, including the crossbar.2. Carefully unpack your new �xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.

PREPARATION

6. Hook the safety cords to the back plate.

8. Secure the �xture to the mounting back plate using the mounting screw (B) and the rubber gasket (C).

9. To prevent moisture from entering the outlet box and causing a short, use clear caulking (i.e. indoor/outdoor silicone sealant) to outline the outside of �xture back plate where it meets the wall. Leave a space at the bottom to allow moisture to escape (Fig.3).

7. Connect the fixture ’s input wires to junction box wires as shown (Fig. 2). Make sure that all wire connectors (A) are secure. If your outlet box has a green or bare copper ground wire, connect the �xture’s ground wire to it. Otherwise, connect the �xture’s ground wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.

NOTE: The side of the mounting plate marked “GND” must face out.

Junction Box

Caulking

Fig. 3 Sealing

5 5/8”

9 1/4”

1 3/4”

1 3/8”

Documents

INSTALLATION INSTRUCTION 486 - LED Outdoor …...- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch