www.simrad-yachting.com | www.lowrance.com

21 4

8765

3

*988-10717-002*

Outboard pilot,Hydraulic packInstallation GuideENGLISH

NAC-1

Operating temperature -25°C to +55°C (13°F to 131°F)

Protection Splashproof, IPx5

Weight 0.6 kg (1.3 lbs)

Power supply 9-16 V DC

Load 140 mA + drive unit load

Performance Drive: 8 A cont., 16 A for 1 s

Pump-1

Operating temperature -15°C to +75°C (5°F to 167°F)

Protection Splashproof, IPx5

Weight 2.2 kg (4.9 lbs)

Load 5 A at 8 bar (116 psi), 7 A at 24 bar (350 psi)

Performance 0.8 l/min at 24 bar (350 psi)

GS25/Point-1

Operating temperature -25°C to +60°C (13°F to 140°F)

Protection Watertight, IPx7

Weight 0.14 kg (0.31 lbs)

Power supply 9-16 V DC

Load <100 mA @ 12 V DC

Performance Heading: +/- 3°, Horiz. accuracy: 3 m (9.8 ft)

Standby/Auto button

Operating temperature -25°C to +55°C (13°F to 131°F)

Protection Splashproof, IPx5

Weight 0.04 kg (0.09 lbs) (including cable)

RC42N

Operating temperature 0°C to +55°C (32°F to 131°F)

Protection IP56

Weight 0.4 kg (0.9 lbs)

Power supply and interface 8-16 V via NMEA 2000

Power consumption 1.4 W

Accuracy ± 3 degrees after calibration

Compass safe distance 0.5 m (1.7’)

PLANNING: Pump-1, Mounting location

CORRECTFLUID LEVEL

MOUNTING: Disconnecting the hoses from helm pump

12

3

STB PO

RT

PLANNING: DimensionsTechnical specifications

PLANNING: Cable lengths

Use to mount Pump-1, NAC-1 and heading sensor.

Drill holes for screws, larger dimensions for hoses.

Wrenches that fit the hoses.

Cup or can for oil spill.

Tape.

Tools to connect power cables at battery.

Gloves (disposable type).

Installing with optional 000-11772-001 Verado fitting kit for Pump-1

PLANNING: Tools needed

2

1

NOTE:THE CONNECTION ARECOLOR INDEPENDENT

1 * Ø 16 mm (0.62”)

Refer to Wiring diagram (point 15) to find the various cable lengths.

PLANNING: GS25/Point-1, Mounting location

GS25/Point-1 The antenna contains a magnetic heading sensor and should not be mounted within 1 meter (3.3 ft) of any potential magnetic source.

RC42NSelect a location that provides a solid mounting place free from vibration, min. 1 meter (3.3 ft) away from any potential magnetic source, and as close to the vessel’s centre of roll and pitch as possible, i.e. close to the water line.

Potential sources for magnetic/electromagnetic interference include:• Electrical Motors/Magnets/Moving Metal items• Outboard Engines• High current electrical sources such as main power cables,

batteries, distribution panels etc.

Electromagnetic Interference

0.5 m (20”) Min 0.5 m (20”) Min2 m (6 ft) Min

RADAR

Magnetic Field

Radio Transmitter

1 m (3.3 ft) Min

RC42N

310 mm

930 mm

VERADO STEERINGCYLINDER VOLUMEAPPROX. 9ci - 150 cc

VERADO ELECTROHYDRAULIC POWER PACK

VERADO HELM

HIGH PRESSURESTEERING LINES

LOW PRESSURERETURN LINE

HIGH PRESSURESUPPLY LINE

RETURN LINE EXTENSION

HIGH PRESSURESUPPLY LINE

HIGH PRESSURESTEERING LINES

STEERING LINES

RETURN LINE

LOW PRESSURERETURN LINE

STEERING LINEEXTENSION

ø 90 mm (3.5”)

204 mm (8.1”)

183 mm (7.2”)57 mm(2.2”)

180 mm(7.1”)

85 mm(3.4”)

190 mm(7.5”)

91 mm(3.6”)

169 mm (6.63”)

155 mm (6.1”) 100 mm (4”)

76 mm (3”) 85 mm (3.4”)

38 mm(1.5”)

ø 90 mm (3.54”)

204 mm (8.03”)

183 mm (7.2”)57 mm(2.24”)

180 mm(7.09”)

183 mm(7.2”)

190 mm(7.5”)

91 mm(3.58”)

169 mm (6.63”)

244 mm (9.6”) 142 mm (5.6”)

38 mm(1.5”)

34.0 (1.3”)

98.0

(3.9

”)86

.0 (3

.4”)

128.0 (5.0”)

72.4

(2.8

”)

106.4 (4.2”)

90.0 (3.5”)

102.

4 (4

.0”)

34.0 (1.3”)

98.0

(3.9

”)86

.0 (3

.4”)

128.0 (5.0”)

72.4

(2.8

”)

106.4 (4.2”)

90.0 (3.5”)

102.

4 (4

.0”)

Compatibility information

The hydraulic kit comes with 1/4 NPT 9/16 UNF fittings for nylon tube or flexible hoses which make them ideally suited for the following steering systems:• Teleflex SeaStar HC5345, HC5347, HC5348, HC5358.• Teleflex BayStar HC4600, HC4645, HC4647, HC4648, HC4658.• Hynautic K6 Steering Rams.• Also rams from Vetus, Uflex, Lecomble and Schmitt can be used.

WIRING: Wiring diagram

MOUNTING: NAC-1

MOUNTING: RC42N

9

13

10

14

11

15

12

16

MOUNTING: Pump-1, Refill oil and bleed system

CORRECTFLUID LEVEL

MOUNTING: Pump-1, Connect hoses

STB

PORT

MOUNTING: Bleeding

Turn wheel gently in both directions, and refill oil.Repeat turning and refilling oil until the oil level is stable and no air bubbles left in the transparent tube, and the outboard engine responds firmly.If air bubbles still remain in the system, follow the bleeding procedure described for the outboard cylinder.

IMPORTANT: Check hoses for leaks

MOUNTING: Connect hoses to helm pump

CORRECTFLUID LEVEL

PORT

STB

STB

PORT

IMPORTANT: TRANSPARENT HOSE

ECHO VIDEO IN NMEA 2K NETWORKPOWER

ECHO VIDEO IN NMEA 2K NETWORKPOWER

+ _12 V DC

MAIN POWERSWITCH

* POINT-1 ONLY

* 1.2 m(4 ft)

0.9 m (3 ft)

FUSE,20 AMP

FUSE,20 AMP2 m (6 ft)

1 m (3 ft)

2 m(3 ft)

2 m(6 ft)

2 m(3 ft)

5 m(15 ft)

0.6 m(2 ft)

1.8 m (6 ft)

0.9 m (3 ft)

2 m (6 ft)

1 m (3 ft)

5 m(15 ft)

0.6 m(2 ft)

1.8 m (6 ft)

ECHO VIDEO IN NMEA 2K NETWORKPOWER

ECHO VIDEO IN NMEA 2K NETWORKPOWER

T T + _12 V DC

MAIN POWERSWITCH T T

* POINT-1 ONLY

* 1.2 m(4 ft)

Opt

iona

l

Point-1 / RC42N

IMPORTANT: TRANSPARENT HOSE

MOUNTING: GS25/Point-1

Configuration

Refer to your Autopilot controller’s documentation for setup instructions.

17

A

C

B 1 * Ø 19 mm (0.75”)2 * Ø 3 mm (0.12”)

SIMRAD

Note the mountingdirection!

LOWRANCE

D

1 2

3 4