Upload
others
View
4
Download
0
Embed Size (px)
Citation preview
INSTALLATION GUIDE
TA-4800
TABLE OF CONTENTS
What’s in the box?
Single Bass/Dual Bass Receiver Setup
SoundShaker Amplifier Setup
Commonly Asked Questions
Wireless Syncing
1
2
3
4
5
Page 1
Part No. 5102Amplifier
Part No. 5024Transmitter
Part No. 5465 Power Supply for Amplifier
Part No. 5423Power Supply for Transmitter
Part No. 8091Amp Base
Part No. 3120Long Cable
Part No. 3031Y-Cable (M/2F)
Part No. 3032Y-Cable (M/2M)
WHAT’S IN THE BOX?
Page 2
SINGLE BASS OUT RECEIVER SETUPThis is the transmitter setup for a single bass out. Please follow each step to ensure that your transmitter and amplifier are connected correctly.
STEP 3. CONNECT YOUR RECEIVER & SUBWOOFER
STEP 2. CONNECT THE 3032 Y-CABLE
STEP 2. CONNECT THE 3031 Y-CABLEConnect the single end of the 3032 Y-Cable to one split end of the 3031 Y-Cable.
Connect the single end of the 3032 Y-Cable to your receiver.
STEP 3. CONNECT THE 3032 Y-CABLE TO YOUR RECEIVER & SUBWOOFERConnect the remaining ends of the 3031 Y-Cable to both your receiver and your subwoofer. Once all connections are secure power up the transmitter.
Connect your receiver to your subwoofer. Once all connections are secure power up the transmitter.
STEP 1. CONNECT THE 3032 Y-CABLE AND POWER SUPPLY
STEP 1. CONNECT THE 3032 Y-CABLE AND POWER SUPPLYConnect the power supply for the transmitter.Connect the split cable end of the 3032 Y-Cable to the Audio In on the transmitter.
Connect the power supply for the transmitter.Connect the split cable end of the 3032 Y-Cable to the Audio In on the transmitter.
3032 Y-Cable
5423 Power Supply
3032 Y-Cable
3031 Y-Cable
Your Receiver
Your Receiver
Your Subwoofer
Your Subwoofer
1
1
2
2
3
3
5024 Transmitter
OFF-ON CODE
DUAL BASS OUT RECEIVER SETUPThis is the transmitter setup for a double bass out. Please follow each step to ensure that your transmitter and amplifier are connected correctly.
Cable Not Included
Cable Not Included
5024 Transmitter
5423 Power Supply
OFF-ON CODE
Page 3
Connect the 3120 Long Cable to the SoundShaker port on the back of the 5012 Amplifier.
STEP 5. CONNECT THE LONG CABLE AND POWER SUPPLY
STEP 6a-6b. CONNECT THE LONG CABLE TO SHORT CABLES
STEP 7a-7b. CONNECT SHORT CABLES TO SOUNDSHAKER(S)
The 3120 Long Cable attaches to the 81-3108 Short Cables.
Connect Power Supply to 15V DC Port on the back of SoundShaker
Amplifier.
NOTE: You can connect up to a total of 4 SoundShakers to each amplifier.
Finish by connecting each SoundShaker to a 81-3108 short cable.
SoundShaker 1
SoundShaker 2
SoundShaker 3
SoundShaker 4
AUDIO-IN 15V DC TRANSDUCERS
POWER X-OVER WIRELESS CODE
OFF
1
2
34
56
7
8
9
10 50HZ
55HZ
60HZ
65HZ
70HZ75HZ
80HZ
85HZ
90HZ
95HZ
100HZ
SOUNDSHAKER AMPLIFIER SETUPThis is the main amplifier setup. Please follow each to step to ensure that your amplifier is installed correctly. Make sure the transmitter is installed and is sending a signal out during the amplifier setup.
5012 SoundShaker Amplifier (Front)
5012 SoundShaker Amplifier (Rear)
5
6a
6b
6c
6d
7a
7b
7c
7d
3120
Lo
ng
Cab
le
5465
Po
wer
Su
pp
ly
81-3108 Short Cable
81-3108 Short Cable
81-3108 Short Cable
81-3108 Short Cable
*SoundShakers are sold seperately.
Page 4
COMMONLY ASKED QUESTIONSBelow is a list of commonly asked questions. If you have any trouble with your SoundShaker please refer to the information below.
Q. DOES THE ORDER IN WHICH I CONNECT MY SOUNDSHAKERS MATTER?A. No, the order in which your SoundShakers are connected to the long cable will not matter.
The signal runs to all outputs when powered.
Q. MY SOUNDSHAKER SYSTEM DOES NOT APPEAR TO BE WORKING.A. Check and make sure all connections and power supplies are secured. Make sure your
transmitter, amplifier, receiver, and subwoofer are all powered up.
Q. IS SOUNDSHAKER COMPATIBLE WITH OTHER WIRELESS AUDIO SYSTEMS?A. SoundShaker is compatible with any audio system that provides an RCA output to connect
SoundShaker to.
Q. I’VE SYNC’D MY AMP BUT DON’T FEEL ANY VIBRATIONS.A. When syncing your amp be sure to check that an audio signal is being sent out. Your amplifier
will not sync without a signal currently running. Refer to the illustration on the next page to learn how to sync up your amplifier.
Page 5
SOUNDSHAKER WIRELESS SYNCINGPlease follow each to step to ensure that your equipment syncs correctly.
Make sure Wireless Switch is set to . MAKE SURE YOU HAVE A MOVIE OR MUSIC PLAYING, press and hold Code Button for a minimum of 3 seconds to begin syncing process. When light blinks rapidly proceed to step 2.
Press and hold Code Button for a minimum of 3 seconds until light blinks rapidly. Red light will turn solid when pairing is completed. (Both units should have solid red lights when paired.)
STEP 2. HOLD TRANSMITTER CODE BUTTON TO COMPLETE SYNC WITH AMP
POWER X-OVER WIRELESS CODE
OFF
1
2
34
56
7
8
9
10 50HZ
55HZ
60HZ
65HZ
70HZ75HZ
80HZ
85HZ
90HZ
95HZ
100HZ
STEP 1. HOLD AMPLIFIER CODE BUTTON TO BEGIN SYNC
PLEASE NOTE: YOUR SOUNDSHAKER SHOULD ALREADY BE SYNC’D WITH YOUR SOUNDSHAKER AMPLIFIER.
1
OFF-ON CODE
2
5012 Amplifier
5024 Transmitter