Page 1 Hook Key 126 45 32 32 (3X) 142 UNLOCK ED 12.8 3.9 OPTIONAL Remove locking tab on the Hook if you wish to create a disassemblable joint. This is best done with a sharp utility knife. 1 2 3 4 5 Installation Guide Pro 55 - Metric Material High Strength Reinforced Nylon Colour Black Fixing Method 8G Screws (8x) or Glue Mark center lines, vertical and horizontal, on both substrates. Flush mounting requires no additional preparation. Line the notches in each component (Hook shown here) with the center lines. Mark-Out Template can also be used. Hold the component in place and fasten to the substrate with 8 x 8G screws. Repeat for matching component. Ensure sufﬁcient screw embedment in substrate. Prior to assembly, establish whether the joint is to be permanent or disassemblable. Assembly the joint remembering the Pro 55 only needs to travel 1 pitch for full engagement. When assembled, the substrates with be separated by the thickness of the engaged Pro 55. See second page for Rebate and Set-Back mounting options. Flush Mounting Striplox Liquidlox can also be used for mounting the Pro 55.

Installation Guide Pro 55 - Metric V1 - Timbecon · 126 45 32 32 (3X) 127 47 47 143 32 (3X) 32 32 (3X) R5 (4X) 32 5 (4X) A A B B 142 UNLOCKED 12.8 3.9 4mm deep Key to be recessed

Download PDF Report

Upload
others
View
6
Download
0

Embed Size (px)

Citation preview

Page 1

Hook Key

126

32 (3

142

LOC

K E

D12.8

3.9

OPTIONAL

Remove locking tab on the Hook if you wish to create a disassemblable joint. This is best done with a sharp utility knife.

2 3

4 5

Installation Guide Pro 55 - Metric

Material High Strength Reinforced NylonColour BlackFixing Method 8G Screws (8x) or Glue

Mark center lines, vertical and horizontal, on both substrates. Flush mounting requires no additional preparation. Line the notches in each component (Hook shown here) with the center lines. Mark-Out Template can also be used.

Hold the component in place and fasten to the substrate with 8 x 8G screws. Repeat for matching component. Ensure sufficient screw embedment in substrate.

Prior to assembly, establish whether the joint is to be permanent or disassemblable.

Assembly the joint remembering the Pro 55 only needs to travel 1 pitch for full engagement.

When assembled, the substrates with be separated by the thickness of the engaged Pro 55.

See second page for Rebate and Set-Back mounting options.

Flush Mounting

Striplox Liquidlox can also be used for mounting the Pro 55.

Page 2

143

12.5

127

47 47

143

8.5

12.8

1 2

Striplox™ and Joinlox® are trademark and patent protected internationally. Installation Guide Pro 55 - Metric V1.2

Part Rebate - each substrate mounting face is rebating as shown. Ensure sufficient screw embedment in substrate.

Setting back the mounting face of either the Hook (as shown) or Key by 12.8mm results in a concelled joint without the need to cut rebates.

Rebate Mounting

Set-Back Mounting

Full Rebate - 1 of the substrate mounting faces is rebating the full depth as shown. Ensure sufficient screw embedment in substrate.

Direction Indic. Load Capacity

A 200 kg

B 106 kg

C 200 kg

• Tested using particle board and fixed with screws.

• Ensure sufficient screw embedment in substrate.

Load Capacity

Installation Aids

Striplox Mark-Out TemplateDeveloped to aid in the installation of the Striplox Pro 55, 90D 98, Mini 60 and 120.

Visit joinlox.com/striplox or call 1800 JOINLOX to find out more about these installation aids.

Striplox LiquidloxInstant adhesive with a 15 second cure time. Liquidlox delivers a strong and reliable connection between Striplox products and most substrates.