INSTALLATION FOG LIGHTS VERSION 1 P/N 08V31 …...SEP 2015 PARTS LIST Fog light harness Switch harness Relay 7 Wire ties Wire tie with holder 6 Aluminum tapes 2 Self-tapping screws,

Publications No.

INSTALLATIONINSTRUCTIONS

Accessory Application

© 2015 American Honda Motor Co., Inc. – All Rights Re

VERSION 1
FOG LIGHTSP/N 08V31-T0A-100D
served. AII02406-16 (150

2016 CR-V

9) 0

Issue Date

SEP 2015

PARTS LIST

Fog light harness

Switch harness

Relay

7 Wire ties

Wire tie with holder

6 Aluminum tapes

2 Self-tapping screws, 5 x 16 mm

20A Fuse

Fuse label

2 Spring nuts

Left fog light

Right fog light

Left trim

Right trim

Light switch

Ground bolt (Not used)

1 of 178V31-T0A-1000-9A

TOOLS AND SUPPLIES REQUIRED

Phillips screwdriver

Diagonal cutters

Ratchet

10 mm Socket

10 mm Open end wrench

Isopropyl alcohol

Shop towel

Tape

Masking tape

Blanket

Scissors

The following tool is available through the Honda Tool and Equipment Program. On the iN, click on: Service > Service Bay > Tool and Equipment Program, then enter the number under “Search.” Or, call 888-424-6857.

• Trim Tool Set (T/N SOJATP2014)

Illustration of the Fog Lights Installed on the Vehicle

QD13104BX

RIGHT FOG LIGHT

LEFT FOG LIGHT

SWITCH HARNESS

20A FUSE

LIGHT SWITCH

FOG LIGHT HARNESS

2 of 17 AII02406-1

INSTALLATION

Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”

1. Disconnect the negative cable from the battery.

Removing the Vehicle Parts

2. Remove the driver’s dashboard panel and unplug the vehicle connector.

�0N2019BG

VEHICLE CONNECTOR

6 CLIPS

DRIVER’S DASHBOARD PANEL

6 (1509) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.

3. Remove the driver’s dashboard under cover.

�0N2021BGPINDRIVER’S DASHBOARD UNDER COVER

KNOB(Turn.)

CLIP

4. Attach the masking tape to the upper column cover as shown.

�0N2023A G

MASKING TAPE

UPPER COLUMN COVER

STEERING WHEEL

© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII02406-1

5. Lower the tilt lever, and turn the steering wheel 90° counterclockwise.

�0N2024BG

PLASTIC TRIM TOOL

STEERING WHEEL

LOCK

UPPER COLUMN COVER

90°

6. Using a plastic trim tool, release the lock as shown.

7. Turn the steering wheel 180° clockwise. Using a plastic trim tool, release the lock as shown.

�0N2025BG

LOCK

UPPER COLUMN COVER

PLASTIC TRIM TOOL

180° Clockwise.

6 (1509) 3 of 17

8. Secure the upper column cover to the meter panel with the tape.

�0N2026A G

UPPER COLUMN COVER

TAPE

2 RETAINING TABS

METER PANEL

9. Remove the two self-tapping screws from the lower column cover.

�0N2027A G

LOWER COLUMN COVER

2 SELF-TAPPING SCREWS

4 of 17 AII02406-1

10. Remove the lower column cover (one self-tapping screw).

QD32703AA

SELF-TAP-PING SCREW

LOWER COLUMN COVER

11. Remove the driver’s front door sill trim.

�0D2801AD

2 RETAINING TABS

3 CLIPS

2 HOOKS

DRIVER’S FRONT DOOR SILL TRIM


12. Pull away the door opening seal, and remove the driver’s kick panel.

�0N2030A G

DOOR OPENING SEAL(Pull away.)

DRIVER’S KICK PANEL

2 CLIPS

13. Remove the two self-tapping screws and the three clips from the left front wheel arch protector.

QD12801AX

3 CLIPS

LEFT FRONT WHEEL ARCH PROTECTOR


FRONT


14. Remove the left front wheel arch protector.

QD12802AXFRONT

6 CLIPS

LEFT FRONT WHEEL ARCH PROTECTOR

3 RETAINING TABS

2 CLIPS

15. Repeat steps 13 through 14 on the right side of the vehicle.

16. Attach the tapes to the front bumper, left headlight, and left front fender as shown.

QD12803BX

TAPES

FRONT FENDER

LEFT HEADLIGHT

RIGHT HEADLIGHT

17. Repeat the same procedure on the right side of the vehicle.

6 (1509) 5 of 17

18. Remove the four clips from the front grille.

QD12804BX

4 CLIPS

FRONT GRILLE

19. Remove the front bumper.

• Remove the two self-tapping screws, two bolts, and six clips.

QD12805BX


FRONT BUMPER

6 CLIPS

2 BOLTS

6 of 17 AII02406-1

• On each side, release the three retaining tabs.

QD12806BXFRONT BUMPER

3 RETAINING TABS

• On each side, release the four retaining tabs.

QD12807BXFRONT BUMPER

4 RETAINING TABS


• Release the four clips and two retaining tabs.

• With the help of an assistant, remove the front bumper.

• Place the front bumper on a blanket after removal.

QD12808CX

FRONT BUMPER

2 RETAINING TABS

FRONT GRILLE

4 CLIPS

20. Remove the four clips from the left front inner fender, and release the left front inner fender. NOTE: Do not fully remove the left front inner fender.

QD12809AX

FRONT

4 CLIPS

LEFT FRONT INNER FENDER


Installing the Fog Light

21. Remove the left cover by releasing the tabs.

QD12901AX

LEFT COVER

8 RETAINING TABS

CLIP

FRONT BUMPER

2 RETAINING TABS

22. Install the spring nut to the front bumper.

QD12902AX

SPRING NUT

FRONT BUMPER

6 (1509) 7 of 17

23. Install the left fog light to the front bumper with two hooks and one self-tapping screw. Hook the two hooks in the order shown.

QD12903AX

FRONT BUMPER

1

SELF-TAPPING SCREW

HOOK 2 HOOK

HOOK LEFT FOG LIGHT2

HOOK1

8 of 17 AII02406-1

24. Install the left trim to the front bumper with one clip and ten retaining tabs.

QD12904AXLEFT TRIM

8 RETAINING TABS

CLIP

FRONT BUMPER

2 RETAINING TABS

25. Repeat steps 21 through 24 on the right side of the front bumper.

Routing the Fog Light Harness

26. Plug the fog light harness 1-pin connector to the vehicle 1-pin connector.

QD12905AX

FRONT

FOG LIGHT HARNESS 1-PIN CONNECTOR

VEHICLE 1-PIN CONNECTOR

FOG LIGHT HARNESS

VEHICLE HARNESS

LEFT FRONT INNER FENDER


27. Secure the fog light harness to the vehicle harness with two wire ties.

QD12906BX

FRONT

VEHICLE PANEL

FOG LIGHT HARNESS GROUND TERMINAL

ALUMINUM TAPE

FRONT VIEW

2 WIRE TIES

FOG LIGHT HARNESS

Align.

VEHICLE GROUND BOLT

ALUMINUM TAPE

VEHICLE GROUND TERMINALS

VEHICLE PANEL(Clean with isopropyl alcohol.)

28. Remove the vehicle ground bolt, and secure the fog light harness ground terminal to the vehicle ground terminals with the vehicle ground bolt just removed.

29. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the aluminum tape will attach. Secure the fog light harness to the vehicle panel with one aluminum tape.


30. Route the fog light harness under the left headlight, and secure one clip on the fog light harness to the bumper beam.

QD13001AX

LEFT HEADLIGHT

VEHICLE HARNESS 2 WIRE

TIES

CLIPFRONT FOG LIGHT

HARNESS

VEHICLE HARNESSBUMPER

BEAM

31. Secure the fog light harness to the vehicle harness with two wire ties.

32. Route the fog light harness along the bumper beam, and secure the clip on the fog light harness to the bumper beam as shown.

QD13002AX

CLIP

FRONT

FOG LIGHT HARNESS

BUMPER BEAMFOG LIGHT

HARNESS

BUMPER BEAM

6 (1509) 9 of 17

33. Using isopropyl alcohol on a shop towel, thoroughly clean the areas where the aluminum tapes will attach. Secure the fog light harness to the bumper beam with three aluminum tapes.

QD13003BX

3 ALUMINUM TAPES

BUMPER BEAM(Clean with isopropyl alcohol.)

FOG LIGHT HARNESS

ALUMINUM TAPE(Cut in half.)

34. Using scissors, cut one aluminum tape in half. Secure the fog light harness to the bumper beam with two pieces of halved aluminum tape.

10 of 17 AII02406-1

35. Route the fog light harness, and secure one clip on the fog light harness to the vehicle panel.

QD13004BX

VEHICLE HARNESS

WIRE TIE FRONT

CLIPVEHICLE PANEL

FOG LIGHT HARNESS

ALUMINUM TAPE

VEHICLE PANEL(Clean with isopropyl alcohol.)

36. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the aluminum tape will attach. Secure the fog light harness to the vehicle panel with one aluminum tape.

37. Secure the fog light harness to the vehicle harness with one wire tie.

38. Reinstall the left front inner fender.


39. With the help of an assistant, bring the front bumper close to the vehicle. Plug the two fog light harness 2-pin connectors to the left fog light and right fog light, and reinstall the front bumper.

QD13005BX

2-PIN CONNECTOR

FRONT BUMPER

FOG LIGHT HARNESS

LEFT FOG LIGHT

RIGHT FOG LIGHT

2-PIN CONNECTOR

Routing the Switch Harness

40. Install the relay into the switch harness relay block.

�0D1404AB

RELAY

RELAY BLOCK

SWITCH HARNESS

WIRE TIE WITH HOLDER

41. Install the one wire tie with holder into the switch harness relay block.


42. Secure the switch harness relay block to the vehicle harness with the wire tie with holder on the switch harness relay block.

QD40407AA

RELAY BLOCK

SWITCH HARNESS

WIRE TIE WITH HOLDER

VEHICLE CLIP

VEHICLE HARNESS

FUSE BOX

43. Plug the switch harness 1-pin connector to the vehicle 1-pin connector.

QD40701BA

VEHICLE 1-PIN CONNECTOR

SWITCH HARNESS 1-PIN CONNECTOR

FUSE BOX

6 (1509) 11 of 17

If the vehicle is equipped with the other accessory harness 4-pin connector, go to step 46; otherwise, continue with step 44.

Without other accessory harness 4-pin connector

44. Route the switch harness along the vehicle harness.

QD40702BA


FUSE BOX

FRONT VIEW

SWITCH HARNESS

Plug in here.

FUSE BOX

45. Plug the switch harness 4-pin connector to the fuse box. Go to step 48.

12 of 17 AII02406-1

With other accessory harness 4-pin connector

46. Route the switch harness along the vehicle harness.

QD52801AA


OTHER ACCESSORY HARNESS 4-PIN CONNECTOR

SWITCH HARNESS

FUSE BOX

OTHER ACCESSORY HARNESS

47. Plug the switch harness 4-pin connector to the other accessory harness 4-pin connector.


If the vehicle is equipped with the other accessory harness 6-pin connector, go to step 49; otherwise, continue with step 48.

Without other accessory harness 6-pin connector

48. Plug the switch harness 6-pin connector to the fuse box. Go to step 51.

QD40703BASWITCH HARNESS 6-PIN CONNECTOR

FUSE BOX

Plug in here.

FUSE BOX

FRONT VIEW


With other accessory harness 6-pin connector

49. Remove the dummy connector from the other accessory harness 6-pin connector.

QD40704AA


FUSE BOX

DUMMY CONNECTOR(Discard.)

OTHER ACCESSORY HARNESS 6-PIN CONNECTOR

50. Plug the switch harness 6-pin connector to the other accessory harness 6-pin connector.

51. Secure the switch harness to the vehicle harness with two wire ties.

QD40705BA

VEHICLE HARNESS

SWITCH HARNESS

FUSE BOX

2 WIRE TIES

6 (1509) 13 of 17

52. Unplug the vehicle connector from the light switch.

QD61101AG

LIGHT SWITCH

STEERING COLUMN

2 RETAINING TABS

LEVER

VEHICLE CONNECTOR

STEERING WHEEL

Do not pull on the lever.

NO

53. Push in on the two retaining tabs, slide the light switch out, and remove it from the steering column. Do not pull on the lever.

14 of 17 AII02406-1

54. Install the new light switch to the steering column. Make sure both retaining tabs are locked in place. Do not push on the lever.

QD61102AG

STEERING COLUMN

LEVER

VEHICLE CONNECTOR

STEERING WHEEL

NEW LIGHT SWITCH

NO

Do not push on the lever.

55. Plug the vehicle connector to the new light switch. Make sure the vehicle harness is not being stretched.


56. If a 20A fuse is already installed in the fuse box, go to step 58, otherwise, plug the 20A fuse into the fuse box.

QD40706BA

FUSE BOX

Plug in here.

FUSE BOX

FRONT VIEW

20A FUSE

57. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the fuse label will attach. Attach the fuse label to the fuse seal on the driver’s dashboard under cover.

�0D1510AB

FUSE SEAL

FRONT VIEW

DRIVER’S DASH-BOARD UNDER COVER

FUSE SEAL(Clean with isopropyl alcohol.)

ATTACHING

FUSE LABEL(OPTION FUSE 20A)


58. Remove the relay box upper cover (two retaining tabs).

�A53004AE

RELAY BOX UPPER COVER

2 RETAINING TABS

FRONT

LEFT HEADLIGHT

59. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the fuse label will attach. Attach the fuse label to the relay box upper cover.

�A60101BE

FUSE LABELRELAY BOX UPPER COVER(inside)

FUSE LABELATTACHING POINT(Clean with isopropyl alcohol.)

RELAY BOX UPPER COVER

6 (1509) 15 of 17

60. Check that all wire harnesses are routed properly and all connectors are plugged in.

61. Reinstall all removed parts.

62. Reconnect the negative cable to the battery.

63. Press and hold the radio power button for two seconds to restore the radio and navi (if equipped) system functions.

64. Reset the clock on vehicle without navigation.

USE AND CARE

Check the Operation of the Fog Lights

65. Turn the headlight switch to the “ ” position (headlights on low beam).

66. Turn on the fog light switch (indicator is on).

67. If the fog lights do not turn on, check the fuse and all the connectors, including the ground cable.

053101AB

FO

G L

IGH

T

SW

ITC

H

HEADLIGHT SWITCH

Low HighOFF

ON

OFF - - - -

- - -ON

NOTE: The fog light lenses may cloud when the outside temperature is cold; this is normal and should go away in warm weather.

16 of 17 AII02406-1

How to Aim the Fog Lights

68. Adjust the fog light:

• To adjust, turn the aiming adjustment screw in or out until the correct aiming is obtained.

• Adjust the aiming according to local laws and regulations.

QD13006AX

LEFT FOG LIGHT

To raise.To lower.

FRONT BUMPER

LEFT TRIM


BULB REPLACEMENT

1. Release the splash shield (one bolt and one clip).

QD13101AXCLIP

SPLASH SHIELD BOLT

2. Insert your hand inside of the splash shield released in step 1. Unplug the connector from the fog light.

QD13102AX

FOG LIGHT BULB

CONNECTOR

3. Remove the bulb.


4. Install the new bulb to the fog light.

• Use only a Genuine Honda halogen light bulb of specified wattage.

Rating: 12V 35W H8 Halogen Light Bulb P/N 33165-TL0-003

• Do not touch the bulb. Oily or greasy substances on the bulb can shorten its service life due to the heat produced when the bulb is turned on. If the bulb is accidentally touched, wipe it clean with a soft cloth that has been dampened with a denatured alcohol or a mild detergent solution.

• When installing the new bulb, align the cutout on the fog light with the tab on the new bulb and turn the new bulb in completely. If not properly aligned, the fog light may annoy oncoming driver’s.

QD13103AX

NEW BULBTurn.

FOG LIGHT

CONNECTOR

NEW BULB

5. Reinstall the removed parts. Check that the wire harnesses are not pinched. Be sure to tighten the clip and bolts securely.

6. Check the operation of the fog light; adjust the aiming if necessary.

6 (1509) 17 of 17

Documents

INSTALLATION FOG LIGHTS VERSION 1 P/N 08V31 …...SEP 2015 PARTS LIST Fog light harness Switch harness Relay 7 Wire ties Wire tie with holder 6 Aluminum tapes 2 Self-tapping screws,