TYXIAInstallation and User Guide

Wireless receiverTYXIA RF 651 - 2 channels

Device compliant with the requirements of directives:R&TTE 1999/5/CE

Because of changes in standards and equipment, the characteristics given in the textand the illustrations in this document are not binding unless confirmed by Delta Dore.

• Carefully read these instructions prior to installa-tion.

• The unit must be installed in compliance with cur-rently applicable standards.

• Always switch off the mains before installing orservicing the unit.

• Do not attempt to repair the unit yourself; an after-sales service is available.

• The receiver power supply cable must only bereplaced by the manufacturer or an approvedagent.

• Check that the fastenings are suited to the surfacethat the unit will be attached to (plasterboard,brick, etc.).

• The diagrams provided are simplified for greaterclarity. The protective units and other accessoriesrequired by the standards are not illustrated.

Standard UTE NF C15-100 and good practice mustbe complied with. Connected or nearby equipmentmust not generate excessive interference (directive2004/108/EEC).

Warnings Presentation

TYXIA RF 651 controls lightings, garage doors,electric gates, or roller shutters.

Screw-mountingMounted on a wall usingthe screws and pegssupplied.

Mounting by double-sided adhesive tape

Mounting on the wall using thedouble-sided adhesive tapesupplied.Ensure that the surface onwhich the tape is applied isthoroughly clean before atta-ching the tape.

Mounting

Antenna

Electric cable

Buttons

Channel1 LED

Channel 2 LED

1 2

Connection

100 Wmax.

100 Wmax.

The maximum power directly controlled is limited to 100 W. Above this limit, you must use a contact switch.

Contactswitch 1

Contactswitch 2

N L

bluewire

brownwire

Mainspower 230 V

bluewire

brownwire black wire

grey wire

black wire

grey wire

Grey

3 A

3 A

BlackBrown

Blue

Simple lighting mode (lighting)

Operation on the TYXIA RF 651Pressing the button 1 or 2 of the receiver changesthe current status of the relevant channel (on oroff).

Inverting the contact position of a relayDuring an On command: the relay closes.During an Off command: the relay opens.To reverse the operation of a relay, press the corres-ponding button (1 or 2) on the receiver for 10seconds.

Simple lighting mode with an associatedTYXIA transmitter

The simple lighting mode can be controlled by aTYXIA transmitter (transmitter switch, key ringremote control, etc.).

Associating a button with the receiver

On the receiver, press the button of the channelyou want to associate until the LED flashes (~3seconds).2 possible choices.Slow flashing: simple lighting modeRapid flashing: pulse mode.Press the receiver button 1 or 2 to switch from onerate of flashing to the other.Select the slow flashing.On the transmitter, press and hold the buttondown for approximately 5 seconds.The button will light up, go out then light up again.Release.Check that the receiver’s LED is no longer flas-hing.

The transmitter button is associated with

the receiver channel.

Command sent

ON

OFF

Contact Inverted contact

ON

ON

OFF

OFF

Associating the buttons with thereceiver

On the receiver, press the button of the channelyou want to associate until the LED flashes (~3seconds). 2 possible choices.Slow flashing: simple lighting modeRapid flashing: pulse mode.Press the receiver button 1 or 2 to switch from onerate of flashing to the other.Select the slow flashing.On the transmitter, press and hold down the and buttons together for about 5seconds.

The buttons will light up, go out, then light upagain. Release.Check that the receiver’s LED is no longer flas-hing.

The and transmitter buttons are asso-

ciated with the receiver channel.

Associating a button with the receiver

On the receiver, set the appliance to the required status (e.g. Light is off), press the button of thechannel you want to associate until the LED fla-shes (~3 seconds). 2 possible choices.Slow flashing: simple lighting modeRapid flashing: pulse mode.Press the receiver button 1 or 2 to switch from onerate of flashing to the other.Select the slow flashing.

On the transmitter, press and hold the buttondown for approximately 5 seconds.The button will light up, go out then light up again.Release.Check that the receiver’s LED is no longer flas-hing.

The transmitter button is associated withthe receiver channel.

Simple lighting mode with an associatedTYXAL detector

The simple lighting mode can be associated with aTYXAL detector (opening, movement, technical,etc.).

On the receiver, press the button of the channelyou want to associate until the LED flashes (~3seconds).On the receiver, press the Test key (emits abeep).Check that the receiver’s LED is no longer flas-hing.

The detector is associated with the receiverchannel.

OffOn

OffOn

OffOn

Either is possible, depending on the scenario

OR

Each function of the receiver can record up to amaximum of 8 associations (buttons, transmitters,etc.).

One button (scenario) can control differentreceivers simultaneously (roller shutters, dimmer,simple lighting, etc.).

TroubleshootingYou cannot associate a transmitter with yourreceiver.The maximum number of transmitters to associatewith a receiver function is 8.Check that this number has not been reached.

Lights only come on for 1 second each time abutton is pressed.Pulse mode is enabled.Put the unit into simple lighting mode (refer to the“Association in simple lighting mode” chapter).

The receiver does not recognize the commandfrom a transmitter.• The transmitter is not associated with the recei-ver.• The receiver is still in association mode.• The transmitter batteries are low.

No LED lights up on the receiver.The receiver is not powered.Check the receiver power supply line.

Technical characteristics

• 230 V, 50 Hz power supply, +/-10%• Class II insulation• Power consumption: 0.5 VA• Max. power per output: 3 A 230 Veff Cos ϕ

=1 or 100 W max. for lighting control,• Radio frequency 868 MHz (standard EN 300

220)• Radio range 100 to 300 metres outside,

variable depending on the associated equip-ment (the range can be altered dependingon the installation conditions and the electromagnetic environ-ment)

• Number of transmitters that may be associa-ted with the receiver: 8 max.

• Automatic action: type 1.C (brownout)• Operating temperature: -5°C to +55°C• Storage temperature: -10 to +70°C• Dimensions: 54 x 102 x 19,5 mm• Protection index: IP 44 - IK 04• Install in an environment with normal pollu-

tion levels

ON OFF

Lights switch off 90 seconds after the last detection

Lights switchon followingdetection

ON OFF

Lights switch off at the end of detection

Lights switch on following detection

The receiver can record up to a maximum of 8associations (buttons, transmitters, etc.).

Simple lighting mode with an associatedTYXAL control unit

The simple lighting mode can be associatedwith a TYXAL alarm control unit.On the control unit, enable theMaintenance mode (see control unit guide).On the receiver, press the button of thechannel you want to associate until the LEDflashes (~3 seconds).

Slow flashing:➪ alarm status transfer (channel 1)

- light on when the control unit is in surveillancemode.

- light off when the control unit is not in surveil-lance mode.

➪ alarm transfer mode (channel 2)- light on for 1.5 minutes in the event of an alarm

Rapid flashing:➪ transfer of alarm surveillance enabling/disabling

- enabling the surveillance: lights flash once- disabling the surveillance: lights flash twice

Press the button to pass from one rate of flashingto the other.Press the “Test” button of the control unit.Check that the receiver’s LED is no longer flashing.The control unit is associated with the receiver.

Simple lighting mode with an associatedTYDOM transmitter

The simple lighting mode can be associated with aTYDOM transmitter.

To associate the receiver with the TYDOM, pleaserefer to the respective guides.

Removing all the associations with thereceiver in pulse mode or simple lightingmode

Press and hold down the button of the channel toremove.The corresponding LED flashes after 3 seconds.Hold down the button.The relay reverses after 10 seconds and the LEDno longer flashes.Hold down the button.The LED flashes after 30 seconds; all the associa-tions with the channel are removed.Release the button.

TYDOM 3xx telephone transmitter

TYDOM 2xx multifunction remote control

TYDOM 3xx enables the ON/OFF feature to be operated remotely.

TYDOM 2xx includes all the functions of the TYXIA buttons:

DELTA DORE Bonnemain - 35270 COMBOURG - France

E-mail : deltadore@deltadore.com

*2701909_Rev.1*

Connection

LowerRaise

NeutralEarth

3 A

3 A

N L

blue wire

Mains power230 V

brown wire black wire

grey wire

GreyBlack

BrownBlue

Roller shutter mode

Operation on the TYXIA RF 651The buttons 1 and 2 raise or lower the roller shut-ters.

The shutter rises

The shutter stops

Press andrelease

Press briefly a 2nd time

Note: Pressing briefly during the lowering of the shutter commands the shutter to rise.

Raising control

The shutter lower

The shutter stop

Press and release

Press briefly a 2nd time

Note: Pressing briefly during the raising of the shutter commands the shutter to lower.

Lowering control

1

1

1

2

2

2

- Once the receiver has been associated with atransmitter, check that the Raise transmitter but-ton controls the raising of the roller shutter.If not, switch around the 2 raise/lower wires onyour receiver.- The raise lower contacts are timed to 1 minute.

Roller shutter mode with an associatedTYXIA transmitterRaising and lowering the roller shutters can beassociated with a TYXIA transmitter (transmitterswitch, key ring remote control, etc.).

Associating the buttonsOn the receiver, simultaneously press the buttons 1and 2 until they alternately flash (~3 seconds).On the transmitter, simultaneously press and holdthe buttons and until the LED comes on.Release.Check that the receiver LEDs are no longer flas-hing.The transmitter buttons and are associatedwith the receiver.

Associating a button (scenario)

On the receiver, set the appliance to therequired status (e.g. shutters lowered), pressthe buttons 1 and 2 until they alternately flash(~3 seconds).On the transmitter, press and hold the button down for approximately 5 seconds. TheLED will light up, go out, then light up again.Release.Check that the receiver LEDs are no longerflashing.The transmitter button is associated withthe receiver.

One button (scenario) can control differentreceivers simultaneously (roller shutters, dimmer,simple lighting, etc.).

Raising or lowering

Raising or lowering (choice of 1, depending on the scenario)

Each function of the receiver can record upto a maximum of 8 associations (buttons,transmitters, etc.).

Roller shutter mode with an associatedTYXIA detector

Raising and lowering the roller shutters can beassociated with a TYXAL detector (opening, move-ment, technical, etc.).

On the receiver, simultaneously press the buttons 1and 2 until they alternately flash (~3 seconds).2 possible choices.Slow flashing: a detected presence will cause theroller shutters to rise,Rapid flashing: a detected presence will cause theroller shutters to lower,Press the receiver button 1 to pass from one rate offlashing to the other.

On the receiver, press the Test key (emits a beep).Check that the receiver LEDs are no longer flas-hing.The detector is associated with the receiver.

Roller shutter mode with an associatedTYXIA control unit

Raising and lowering the roller shutters can beassociated with a TYXAL alarm control unit.

Set the control unit to Maintenance mode (see itsguide).

On the receiver, simultaneously press the buttons 1and 2 until they alternately flash (~3 seconds).2 possible choices.Slow flashing: enabling the alarm surveillance willtrigger the lowering of the roller shutters, disablingthe alarm will raise the shutters.

Blinds are lowered when the alarm is enabled and raised when it is disabled.

Blinds are lowered when the alarm is enabled and no change is made when it is disabled.

OR

Raise on presence detection

OR Lower on presence detection

Pulse mode (remote control switch, garage door, electric gate)

Connection

Example 1 :2 lighting outputs

Remotecontrol

switch 1Remote control

switch

Control ofan opening

(e.g.: a gate)

The outputs 1 and 2 are supplied with power (230 V) To control an opening, you must relay.

Remote controlswitch 2

Example 2 :1 lighting output1 open command output

bluewire

brownwire black wire

grey wireblue wire

brown wireblackwiregreywire

Grey

3 A

3 A

BlackBrown

Blue

N L

Operation on the TYXIA RF 651Pressing the button 1 or 2 of the receiver changesthe current status of the relevant channel (on oroff).

Operating with the associated TYXIA orTYDOM transmitter

Pressing the 1 or 2 button on the receiver changesthe current state (on or off).On the receiver, press the button of the channelyou want to associate until the LED flashes (~3seconds).

IMPORTANT : To use the receiver in pulse mode, itmust be associated with a transmitter.The pulse mode can only be controlled by a (TYXIA) or (TYDOM 200) button.

or(status being modified)

2 possible choices.Slow flashing: simple lighting modeRapid flashing: pulse mode.Press the receiver button 1 or 2 to move from onerate of flashing to the other.Select the rapid flashing.

On the transmitter, press and hold the buttonfor 5 seconds.The button will light up, go out then light up again.Release.Check that the receiver’s LED is no longer flas-hing.

The transmitter button is associated with

the receiver channel in pulse mode.

To associate a TYXIA RF 651 with a TYDOM 2xx,please refer to the TYDOM 2xx guide..

Removing all the associations with thereceiver in pulse mode or simple lightingmode

Press and hold down the button of the channel toremove.The corresponding LED flashes after 3 seconds.Hold down the button.The relay reverses after 10 seconds and the LEDno longer flashes.Hold down the button.The LED flashes after 30 seconds; all the associa-tions with the channel are removed.Release the button.

Rapid flashing: enabling the alarm will trigger the lowering of the roller shutters, disabling the alarmwill have no action.Press the receiver button 1 to pass from one rate of flashing to the other.

Press the Test button of the control unit.The control unit emits a beep.Check that the receiver’s LED is no longer flashing.The control unit is associated with the receiver.

Roller shutter mode with an associatedTYDOM transmitter

The simple lighting mode can be associated with aTYDOM transmitter.

To associate the receiver with the TYDOM, pleaserefer to the respective guides.

Removing all the associations with theroller shutters

Press and hold the receiver buttons 1 and 2 (after 3 seconds, the LEDs flash).Hold the buttons down (approximately 30 seconds)until the LEDs flash to confirm that all the receiverassociations are removed.

TYDOM 3xx telephone transmitter

TYDOM 2xx multifunction remote control

TYDOM 3xx remotely raises and lowers the roller shutters:On = raiseOff = lower

TYDOM 2xx includes all the functions of the TYXIA buttons: