Upload
others
View
3
Download
0
Embed Size (px)
Citation preview
Publications No.
INSTALLATIONINSTRUCTIONS
Accessory Application
© 2008 American Honda Motor Co., Inc. – All Rights Re
AII 40101
FOG LIGHTSserved. AII 40101 (0808
2009-2010 CIVIC2-DOOR (EX-L)
) 0
Issue Date
AUG 2008
PARTS LISTRight fog light
Left fog light
Switch harness
Fog light harness
Sub harness
Switch
14 Wire ties
Wire tie with holder
4 Spring nuts
4 Self-tapping screws
20 A fuse(Some may not be used.)
Relay
TOOLS AND SUPPLIES REQUIREDPhillips screwdriverFlat-tip screwdriverRatchet10 mm SocketGlovesBlanketDiagonal cutters5 mm Hex wrenchShop towelMasking tape
1 of 138V31-SVA-1F00-91
Illustration of the Fog Lights Installed on the Vehicle
852201AK
SUB HARNESS
SWITCH HARNESS SWITCH
RELAY
RIGHT FOG LIGHT
FOG LIGHT HARNESS
LEFTFOG LIGHT
20 A FUSE
2 of 13 AII 40101
INSTALLATION
1. Make sure you have the anti-theft codes for the audio system, then write down the radio presets.
2. Disconnect the negative cable from the battery.
3. Remove the radiator cover (two expansion clips and two clips).
Customer Information: The information in thisinstallation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
5311021T
2 CLIPS(Pull vertically.)
RADIATOR COVER
EXPANSION CLIP
PANEL
(0808) © 2008 American Honda Motor Co., Inc. – All Rights Reserved.
4. With the help of an assistant, remove the front bumper (six clips, two self-tapping screws, two socket bolts and two bumper bolts). To prevent damage, set the front bumper on a blanket.
5. Remove the left fog light cover (five pawls).
851308AK
6 CLIPS
FRONT BUMPER
2 SELF-TAPPING SCREWS
2 SOCKET BOLTS
2 BUMPER BOLTS
840801AK
LEFT FOG LIGHT COVER
5 PAWLS
FRONT BUMPER
© 2008 American Honda Motor Co., Inc. – All Rights Reserved. AII 40101
6. Install the two spring nuts onto the front bumper.
7. Install the left fog light to the fog light cover opening, and secure it with two self-tapping screws.
8. Repeat steps 5 through 7 on the other side.
9. Route the fog light harness 2-pin connector between the lower grille and the front bumper from the right side through the left side.
851303AK 2 SELF-TAPPING SCREWS
FRONT BUMPER
FRONT BUMPER
2 SPRING NUTS
LEFTFOG LIGHT
851304AK
FRONT BUMPER
FOG LIGHT HARNESS 2-PIN CONNECTOR
FOG LIGHTHARNESS2-PIN/4-PINCONNECTORS
FRONT BUMPER
FOG LIGHT HARNESS
LOWER GRILLE
(0808) 3 of 13
10. Plug the fog light harness 2-pin connector into the left fog light connector.
11. Install the fog light harness clip onto the lower grille rib.
12. Plug the fog light harness 2-pin connector into the right fog light connector.
13. Install the fog light harness clip onto the lower grille rib.
851305AK
FOG LIGHT HARNESS2-PIN CONNECTOR
LEFT FOG LIGHT CONNECTOR
LOWER GRILLE RIB
FOG LIGHT HARNESS CLIP
851306AK LOWER GRILLE RIB
FOG LIGHT HARNESS2-PINCONNECTOR
RIGHTFOG LIGHTCONNECTOR
FOG LIGHT HARNESS CLIP
4 of 13 AII 40101
14. Secure the fog light harness to each rib of the lower grille with one wire tie.
15. Remove three bolts from the washer tank.
851307AK
FOG LIGHT HARNESS
LOWER GRILLE
2 WIRE TIES
FOG LIGHT HARNESS
FOG LIGHT HARNESS
852101AK
3 BOLTSWASHER TANK
(0808) © 2008 American Honda Motor Co., Inc. – All Rights Reserved.
16. Remove the vehicle ground bolt, and reinstall it to the vehicle ground terminal with the sub harness ground terminal as shown.
17. Reinstall the washer tank. Check that the pipe of the washer tank is installed securely.
852102AK
SUBHARNESSGROUND TERMINAL
VEHICLE GROUNDTERMINAL
SUB HARNESS
VEHICLE GROUND BOLT(Reuse.)
PIPE
© 2008 American Honda Motor Co., Inc. – All Rights Reserved. AII 40101
18. Locate the vehicle 1-pin connector blue-taped to the vehicle harness and remove the blue tape to free the connector. Plug the vehicle 1-pin connector into the sub harness 1-pin connector.
19. Route the sub harness as shown and secure it to the vehicle harness using three wire ties.
20. Install the wire tie with holder on the sub harness 4-pin connector.
21. Secure the wire tie with holder to the vehicle harness.
852103AK
FRONT
VEHICLE HARNESS
SUBHARNESS
VEHICLE1-PIN CONNECTOR
BLUE TAPE(Remove.)
SUB HARNESS1-PIN CONNECTOR
842802AK
3 WIRE TIES
WIRE TIE WITH HOLDER
VEHICLE HARNESS
FRONTSUB HARNESS4-PIN CONNECTOR
(0808) 5 of 13
22. Plug the fog light harness 4-pin connector into the sub harness 4-pin connector.
23. Reinstall the front bumper.
24. Remove the cover from the trunk lid/fuel fill door opener (six retaining tabs), and remove one self-tapping screw.
25. Using the key, unlock the opener.
852202AK
SUB HARNESS4-PIN CONNECTOR
FRONT BUMPERFOG LIGHT HARNESS
4-PIN CONNECTOR
5202191T
OPENER LOCK CYLINDER
KEY
SELF-TAPPING SCREW
COVER 6 RETAINING TABS
TRUNK LID/FUEL FILL DOOR OPENER
6 of 13 AII 40101
26. Raise the front side of the left front door sill trim (six clips, retaining tab and hook).
27. Remove the footrest.• Using a hex wrench, remove the lower clip from
the stud bolt.• Using a flat-tip screwdriver, remove the upper
clip from the stud bolt.
5311351T
RETAINING TAB
HOOK
FRONT
6 CLIPS
LEFT FRONT DOOR SILL TRIM
5311370T
HEX WRENCH
STUD BOLT
UPPER CLIP
LOWER CLIP
FOOTREST
(0808) © 2008 American Honda Motor Co., Inc. – All Rights Reserved.
28. Pull away the weatherstrip from the left kick panel and remove the left kick panel (two clips).
29. Remove the driver’s dashboard under cover (turn the lock knob 90° counterclockwise, and release the two clips and pin).
5202220T
WEATHERSTRIP2 CLIPS
LEFT KICK PANEL
5202112T
2 CLIPS
DRIVER’S DASHBOARD UNDER COVER
KNOB
© 2008 American Honda Motor Co., Inc. – All Rights Reserved. AII 40101
30. Remove the driver’s dashboard lower cover (eight clips).
31. Remove the vehicle white 34-pin connector from the fuse box by pushing the retaining tab and raising the lock lever of the connector. Return the lock lever on the vehicle white 34-pin connector and remove the cover by sliding it.
5202121T
8 CLIPS
DRIVER’S DASHBOARD LOWER COVER
851202AK
Push.
VEHICLE WHITE 34-PIN CONNECTOR
WHITE 34-PIN CONNECTOR
Push. Slide.
Push.RETAINING TAB
COVERFUSE BOX
LOCK LEVER
(0808) 7 of 13
32. Insert the white/red and blue terminals from the switch harness into the vehicle white 34-pin connector.
33. Reinstall the vehicle white 34-pin connector.
34. Plug the switch harness 6-pin connector into the fuse box.
5311150T
SWITCH HARNESS TERMINALS
Harness Side View
LOCK LEVERWHITE/RED TERMINAL
BLUE TERMINAL
SWITCH HARNESS
VEHICLE WHITE 34-PIN CONNECTOR
5311160T
VEHICLE 6-PIN CONNECTOR
SWITCH HARNESS
FUSE BOX
SWITCH HARNESS 6-PIN CONNECTOR
8 of 13 AII 40101
NOTE: If the fuse box 6-pin connector is already being used by another accessory, unplug its 6-pin connector from the fuse box. Locate the 6-pin connector taped to the switch harness, and remove the dummy connector. Plug the other accessory’s harness 6-pin connector into the switch harness, and plug the switch harness 6-pin connector into the fuse box.
5311310T
OTHER ACCESSORY HARNESS 6-PIN CONNECTOR
DUMMY CONNECTOR (Discard.)
SWITCH HARNESS 6-PIN CONNECTOR
FUSE BOX
SWITCH HARNESS 6-PIN CONNECTOR
(0808) © 2008 American Honda Motor Co., Inc. – All Rights Reserved.
35. Route the terminal from the switch harness down.
36. Unplug the vehicle blue 20-pin connector.37. Slide the retainer from the vehicle blue 20-pin
connector backward, and insert the violet terminal from the switch harness into the vehicle blue 20-pin connector. Reinstall the vehicle blue 20-pin connector.
38. Route the switch harness relay block above the knee bolster.
6510010T
SWITCH HARNESS
Harness Side View
SWITCH HARNESS VIOLET TERMINAL
RETAINER
VEHICLE BLUE 20-PIN CONNECTOR
5311180T
SWITCH HARNESS
KNEE BOLSTER
© 2008 American Honda Motor Co., Inc. – All Rights Reserved. AII 40101
39. Plug the relay into the switch harness relay block, then slide the relay block onto the vehicle bracket stay.
40. Remove the vehicle ground bolt. Install the switch harness ground terminal, then reinstall the vehicle ground bolt.
860603AK
SWITCH HARNESS
VEHICLE BRACKET STAY
RELAY
SWITCH HARNESS RELAY BLOCK
5311200T
SWITCH HARNESS
SWITCH HARNESS GROUND TERMINAL
VEHICLE GROUND BOLT (Reuse.)
FRONT
(0808) 9 of 13
41. Locate the 1-pin connector blue-taped to the vehicle harness. Plug the switch harness 1-pin connector into the vehicle 1-pin connector.
42. While wearing gloves, push the switch cover out from the inner side of the meter panel.
5311212T
SWITCH HARNESS SWITCH HARNESS
1-PIN CONNECTOR
VEHICLE 1-PIN CONNECTOR
5311330T
METER PANEL
SWITCH COVER (Discard.)
10 of 13 AII 40101
43. Route the switch harness 5-pin connector through the hole.
44. Plug the switch harness 5-pin connector into the switch and install the switch to the meter panel.
45. Secure the switch harness to the vehicle harness and the knee bolster with nine wire ties in the areas shown.
871720AK
SWITCH
METER PANEL
SWITCH HARNESS 5-PIN CONNECTOR
5311242T
KNEE BOLSTER
VEHICLE HARNESS
SWITCH HARNESS 9 WIRE TIES
(0808) © 2008 American Honda Motor Co., Inc. – All Rights Reserved.
46. Install the 20 A fuse into the fuse box in the location shown. If the fuse is already installed, it is not necessary to install the fuse from the kit.
47. Check that all wire harnesses are routed properly and all connectors are plugged in.
48. Reinstall all removed parts.49. Connect the negative cable to the battery and check
operation of all lights and other electrical accessories.
50. Enter the anti-theft codes for the audio system, and reset the radio station presets.
51. Reset the clock.
5307240T
FUSE LOCATION “6”
20 A FUSE
FUSE BOX
FUSE BOX
© 2008 American Honda Motor Co., Inc. – All Rights Reserved. AII 40101
USE AND CAREHow to Operate the Fog Lights
• Turn the light switch to the “ ” position (headlights on low beam).
• Press the fog light switch (indicator is on).
NOTE: The fog light lenses can cloud when the outside temperature is cold; this is normal and should go away in warm weather.
Adjusting the Aim1. Adjust the vertical aim according to local laws and
regulations. Turn the adjusting screw in or out until the correct angle is obtained.
2. Repeat on the right side.
871715AK
FOG
LIG
HT
SWIT
CH
OFF
Low High
-
-
-
-
- -
-
OFF
HEADLIGHT SWITCH
ON ON
851403AK
ADJUSTING SCREW
To raise.To lower.
(0808) 11 of 13
BULB REPLACEMENT1. Remove the two self-tapping screws, and pull the fog
light out toward you.
2. Unplug the connector from the fog light while pushing the retaining tab of connector.
851404AK
2 SELF-TAPPING SCREWS
FOG LIGHT
851405AK
RETAINING TAB(Push.)
CONNECTOR
FOG LIGHT
12 of 13 AII 40101
3. Remove the bulb from the fog light by turning it.
851406AK
FOG LIGHT
BULB
(0808) © 2008 American Honda Motor Co., Inc. – All Rights Reserved.
4. Install a new bulb on the fog light by turning it clockwise until it stops.• Take extreme care when replacing the fog light
bulb to avoid damaging the lenses or finished surfaces of the body.
• Use only a Honda Genuine halogen light bulb of specified wattage. Rating: 12V 55W H11 Halogen Light Bulb P/N33165-S5A-003
• Do not touch the bulb. Oily or greasy substances on the bulb can shorten its service life due to the heat produced when the bulb is turned on. If the bulb is accidentally touched, wipe it clean with a soft cloth that has been dampened with a denatured alcohol or a mild detergent solution.
• When installing the new bulb, align the cutout on the fog light with the tab on the new bulb and turn the new bulb in completely. If not properly aligned, the fog light may blind oncoming drivers.
5. Plug the connector into the bulb.6. Reinstall the fog light.7. After the replacement, check that the bulb comes on
properly. Adjust the fog light aiming adjustment as necessary.
851407AK
CONNECTOR
FOG LIGHT
NEW BULB
Turn the bulb until it stops.
© 2008 American Honda Motor Co., Inc. – All Rights Reserved. AII 40101
(0808) 13 of 13