Embed Size (px)
Citation preview
ZEROBasic Drain
INSTALLATION MANUAL
Basic Drain Zero - Linear shower drain
Easy Drain®
2 Basic Drain
CONTENTS
Easy Drain®
Installation options ........................................................ 3
Installation guide | Electrical grounding ............................. 3
Installation guide | Standard clamp drain ........................... 4
Installation guide | No-hub sleeve .................................... 6
Installation guide .......................................................... 7
Installation diagram - Wall | Standard clamp drain ............. 9
Installation diagram - Wall | No hub sleeve ....................... 10
Important assembling advice .......................................... 11
3 Basic Drain
INSTALLATION OPTIONS
Along the wall Centered | Wall-to-Wall At the entrance
1 2
INSTALLATION GUIDE | ELECTRICAL GROUNDING
4 Basic Drain
CLAMP DRAIN* NOT INCLUDED
MAKE SURE THE CONNECTION BETWEEN THE CLAMP DRAIN BASE AND SIPHON/DISCHARGE PIPE IS WATERTIGHT!
CONCRETE BOARD (AT LEAST ¼” ABOVE THE FLOOR)
2 3
4 5
6 7
INSTALLATION GUIDE | STANDARD CLAMP DRAIN
PAN LINER WITH ADHESIVE BONDING
SLOPED MORTAR BED
SEAL THE ENTIRE FLOOR WITH PAN LINERREMOVE AIR POCKETS BENEATH THE LINER
*NOTE: Clamp drain may vary depending on model being used
THE TOP OF THE CLAMP DRAIN MUST BE INSTALLED AT LEAST ½ ” ABOVE THE WOODEN FLOOR
8A
OPTION: CURBLESS SHOWER INSTALLATION
8B
5 Basic Drain
10
11 12
13
9
>> CONTINUE ON PAGE 8
14
6 Basic Drain
INSTALLATION GUIDE | NO-HUB SLEEVE
CONCRETE BOARD (AT LEAST ¼” ABOVE THE FLOOR)
2
3 4
5 6
1
PAN LINER WITH ADHESIVE BONDING OVER THE FIRST
SLOPED MORTAR LAYER
SEAL THE ENTIRE FLOOR WITH PAN LINERREMOVE AIR POCKETS BENEATH THE LINER
NO-HUB SLEEVE* NOT INCLUDED
INSTALL SHOWER IN COMPLIANCE WITH UPC STANDARD
87
>> CONTINUE ON PAGE 8
OPTION: CURBLESS SHOWER INSTALLATION
7 Basic Drain
SLOPED MORTAR BED FLEXIBLE SEALING COMPOUND
1 2
3A 3B
4 5
66
INSTALLATION GUIDE
Centered Wall-to-Wall
8 Basic Drain
SEAL THE ENTIRE FLOOR WITH THIN-SET MEMBRANEREMOVE AIR POCKETS BENEATH THE MEMBRANEFLEXIBLE SEALING COMPOUND
7
9 10
11
8
FLEX. TILE ADHESIVE
13
12
9 Basic Drain
INSTALLATION DIAGRAM | STANDARD CLAMP DRAIN
*Not included with the drain.
1 Basic Drain rough
2 Grating
3 Strainer
4 Elastic sealant - Silicone
5 Tiles
6 Thin set tile adhesive
7 Grout
8 Pre-assembled waterproofing membrane
9 Thin-set sheet membrane (entire floor!)
10 Sloped mortar bed - first layer
11 Sloped mortar bed - second layer
12 Pan liner / Moisture resistant material
13 Pea Gravel
14 2” Clamping drain base*
15 2” Clamping ring*
16 2” Rubber sealing gasket
17 Sealant between membrane & mortar
18 Drainage pipe
PLYWOOD CONCRETE
3
45
6
7
10
15
1716
13
18
1
2
8 9
11
14
12
10 Basic Drain
INSTALLATION DIAGRAM | NO HUB SLEEVE
*Not included with the drain.
1 Basic Drain rough
2 Grating
3 Strainer
4 Elastic sealant - Silicone
5 Tiles
6 Thin set tile adhesive
7 Grout
8 Pre-assembled waterproofing membrane
9 Thin-set sheet membrane (entire floor!)
10 Sloped mortar bed - first layer
11 Sloped mortar bed - second layer
12 Pan liner / Moisture resistant material
13 No-Hub sleeve*
14 Drainage pipe
PLYWOOD CONCRETE
3
45
6
7
10
13
14
1
2
8 9
11
12
11 Basic Drain
USA
Important assembling advice: Basic Drain®
Suitable for renovation work and new construction
The Easy Drain® Basic Drain should only be installed by trained professionals in compliance with state and local building codes. To achieve the best possible result, please carefully read the installation guide. If you have any questions, please consult your supplier.
▪ Please check the content of the package for completeness and integrity before proceeding with the assembly. Do not install the drain if any deviations are noted. Should this be the case, please consult your supplier.
▪ Prior to construction, the installation procedure and its special considerations should be discussed with the tile setter. After the installation of the drain body (rough) is complete, please provide the tile setter with the complete installation guide.
▪ If the drain is used for large showers with multiple heads, please check to make sure that the drainage capacity is sufficient. If you are unsure, please consult the supplier for advice.
▪ If you do not wish to use the second drainage level (secondary water drainage), the joint between the shower drain body and the TAF (tile frame) should be sealed with a permanent sealer.
▪ We recommend taping or closing the drain opening of the shower drain with a cement cap prior to the assembly to prevent construction debris from getting into the drainage pipe. To prevent damage to the TAF (tile frame), it should be kept in the package until the final installation by the tiler.
▪ Make sure the drain is level all around.
▪ Install the sewage system in compliance with the local and national codes. Note: ensure that the sewage system is properly vented and correctly pitched.
▪ Check the drainage system and the sewer system connection for water tightness.
▪ In order to prevent hollow spaces, all empty space beneath the drain must be completely filled up and sealed with floor pavement up to the top edge of the drain flange.
▪ The seal must be in compliance with the state and local standards.
▪ When tiles are being fitted, the pitch of the tiles (min. 2% per 3’3” (≈1m1)) in the shower must always be sloped towards the drain. The tiles should be laid level or 3/64” (≈1 mm) higher than the top edge of the tile frame to ensure good drainage toward the shower drain. Note: the requirements with regard to the floor gradient may be different for walk-in showers with glass walls. Please consult your supplier in this respect.
▪ Once the tiles have been fitted, the joint between the tiled floor and the TAF (tile frame) should be permanently sealed with an elastic sealant (maintenance joint). The adhesion
surfaces should be free of mortar, adhesive and other adhesion-reducing materials.
▪ The drain is only intended for use with waste water common in households. Do not use other fluids as well as cleaning agents with the potential to damage sanitary equipment, drainage equipment and raw materials.
▪ If the drain is used for other purposes (e.g. swimming pools), where it may come in contact with aggressive cleaning agents or corrosive substances such as salt or chlorine, please consult your supplier.
▪ Construct the floor according to state and local building codes.
▪ Compliance with this installation advice is required for any warranty claims. Deviation from the installation instructions will void the warranty.
Caution !
▪ Tile cleaning products often contain aggressive chemicals that are abrasive in nature and may damage the drain. Please ensure that the drain is thoroughly flushed after using any tile and grout cleaning products.
▪ 10 Years limited warranty only applies when constructed according to all installation instructions.
▪ Glass gratings are not suited for wheelchair accessibility.
MAINTENANCE INSTRUCTIONS
▪ Do not use abrasives and/or sharp/scraping objects to clean the Easy Drain®.
▪ The hair catcher should be cleaned periodically to remove any dirt that may have collected.
▪ We recommend the use of Easy CLEANSET for daily maintenance and cleaning of your Easy Drain®.
Typing and printing errors reserved. Easy Sanitary Solutions BV excludes all liability for any damages whatsoever associated with the use and/or the installation of the drain. Easy Sanitary Solutions BV a priori excludes any liability whatsoever.
E50.01.00.01.49 | 09.14
Easy Drain®
Easy Sanitary SolutionsNijverheidsstraat 60
7575 BK Oldenzaal, The Netherlandstel: +31 (0)541 200800 email: [email protected]
www.easydrain.com
ESS PRODUCTS ARE PATENTED AND REGISTRATED TRADEMARKS MADE BY ESS
Easy Drain® USA Collection2663 Townsgate Rd.
Westlake Village, CA 91362 T: 855 627 3626F: 855 627 7928
email: [email protected]
