Installation 30” Built-In Trivection Instructions...hsei nst ru c ons c m plet ly an dcar efu ly. IMP OR TA NT-Sav et he s in tru tin fo rl o c in sp e t ’su se. IM P TA NT-OBS

131-10663 1-07 JR

Installation 30” Built-In Trivection™

Instructions Wall Oven

JT930, JT980, ZET3038, ZET3058

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT — Save theseinstructions for local inspector’s use.

• IMPORTANT — Observe allgoverning codes and ordinances.

• Note to Installer – Be sure to leave theseinstructions with the Consumer.

• Note to Consumer – Keep theseinstructions for future reference.

• Skill level – Installation of this appliancerequires basic mechanical and advancedelectrical skills.

• Completion time – 1 to 3 hours• Proper installation is the responsibility of

the installer. • Product failure due to improper installation

is not covered under the Warranty.

WARNING — This appliance mustbe properly grounded.

• ATTENTION INSTALLERAll electric wall ovens must be hard wired(direct wired) into an approved junctionbox. A plug and receptacle is NOTpermitted on these products.

FOR YOUR SAFETY:

• Be sure your oven is installed properly by aqualified installer or service technician.

• Be sure the oven is securely installed in acabinet that is firmly attached to the housestructure. Weight on the oven door couldcause the oven to tip and result in injury.Never allow anyone to climb, sit, stand orhang on the oven door.

• Make sure the cabinets and wall coveringsaround the oven can withstand thetemperatures (up to 200°F) generated by the oven.

WARNING: The electrical power tothe oven supply line must be shut off whileline connections are being made. Failure todo so could result in serious injury or death.

• To prevent damage to the door and toprevent excessive microwave leakage, doNOT remove the door on the single walloven or the upper oven door on the doublewall oven.

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com

2

Installation Instructions

PREPARE TO INSTALL THE OVEN

TOOLS YOU WILL NEED

MATERIALS YOU MAY NEED

Wire NutsJunction Box

60” of String for Single Ovens96” of String for Double Ovens

Adjustable Wrench(for 1-7/16” Nut)

Level

Phillips Screwdriver

Drill with 1/8” Bit(Extension may be

required)

Tape Measure

Hand or Sabre Saw

Pencil

Safety Glasses

Gloves

Straight Edge orSquare

PARTS INCLUDED

12 Screws

Strain ReliefClamp for 1/2”conduit

MetalBottom Trim

PlasticBottom Trim

Metal BottomTrim Assembly

OR

3


PRE-INSTALLATION

All installation information on the followingpages is to be used for SINGLE and DOUBLEoven installation!

Remove packaging materials. Checkbehind hinges. Remove plastic on trimsand panel, all tape around the oven, andany shipping screws securing the ovento the base pad. Use caution when liftingthe oven forward; the ovens are frontheavy.

Open oven door and remove literaturepack, broiler pan and grid, and ovenracks.

Remove Installation Instructions fromliterature pack and read them carefullybefore you begin.

Be sure to place all literature, Owner’sManual, Installation Instructions, etc. in asafe place for future reference.

D

C

B

A

1 PRE-INSTALLATION (CONT.)

NOTE: To prevent damage to the door and to prevent excessive microwave leakage, doNOT remove the door on single wall ovenmodels or the upper oven door on doublewall oven models.

The lower oven door on the double wall oven may be removed as an addedconvenience during installation. See Step 4.

DO NOT LIFT THE OVEN BY THE HANDLE!

Place the oven on a table or platformeven with the cutout opening. (Platformmust support 225 lbs. single, 375 lbs.double.)

Remove the bottom trim from the top ofthe oven. It will be installed at the end ofthe installation process.

G

F

E

1

EASY INSTALLATION OF YOUR NEW

30" WALL OVEN

Before you begin-Read these instructions completely and carefully.

IMPORTANT- Save these instructions for local inspector’s use.

IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.

Note to Installer- Be sure to leave these instructions with the consumer.

OWNER- Keep these instructions for future reference.

Note- This appliance must be properly grounded (if applicable).

Before you begin-Read these

instructions completely and

carefully.IMPORTANT- Save these

instructions for local inspector’s use.

IMPORTANT- OBSERVE ALL

GOVERNING CODES AND ORDIANCES.

Note to Installer- Be sure to leave

these instructions with the consumer.

OWNER- Keep these instructions

for future reference.Note- This appliance must be

properly grounded (if applicable).

FOR YOUR SAFETY













ELECTRICAL REQUIREMENTS



















































FOR YOUR SAFETY
































































FOR YOUR SAFETY
































































FOR YOUR SAFETY















































Before you begin-Read these instructions completely and carefully.IMPORTANT- Save these instructions for local inspector’s use.IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.Note to Installer- Be sure to leave these instructions with the consumer.OWNER- Keep these instructions for future reference.Note- This appliance must be properly grounded (if applicable).


FOR YOUR SAFETY




Before you begin-Read these instructions completely and carefully.IMPORTANT- Save these instructions for local inspector’s use.IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.Note to Installer- Be sure to leave these instructions with the consumer.OWNER- Keep these instructions for future reference.Note- This appliance must be properly grounded (if applicable).Before you begin-Read these instructions completely and carefully.IMPORTANT- Save these instructions for local inspector’s use.IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.Note to Installer- Be sure to leave these instructions with the consumer.OWNER- Keep these instructions for future reference.Note- This appliance must be properly grounded (if applicable).




FOR YOUR SAFETY








FOR YOUR SAFETY








EASY INSTALLATION OF YOUR NEW 30" WALL OVEN


FOR YOUR SAFETY





Oven Racks

LiteraturePack

Broiler Panand Grid

4


SINGLE BUILT-IN OVEN CUTOUT OPTIONS

WALL MOUNT—SINGLE BUILT-IN OVENOPTION

Cabinet Width 30”

Recommended Cutout Location from Floor 32 1/2”

Cutout Depth 23 1/2” Min.

Cutout Width 28 1/2” Min.28 5/8” Max.

Cutout Height 27 1/4” Min.27 5/16” Max.

A

WALL MOUNT—SINGLE BUILT-IN OVENOPTION (CONT.)

NOTE: If the cabinet does not have a frontframe and the sides are less than 3/4” thick,shim both sides equally to establish thecutout width.If the cabinet does not have a solid bottom,two braces or runners must be installed levelwith the bottom of the cutout to support theweight of the oven. For single ovens, therunners and braces must support 225 lbs.The solid bottom or runners must be levelwith the bottom of the cutout or the bottomtrim may not install correctly and theninterfere with the door opening.

NOTE: This oven is not approved forstackable or side by side installation.

A

7”

21”

Cutout Width28 1/2” Min28 5/8” Max.

All corners mustbe cut square

Allow 11/16” foroverlap of ovenover side edges of cutout

Cutout Height27 1/4” Min.27 5/16” Max.

Openingbetweeninside wallsmust be at Least 28 1/2” Wide

Required JunctionBox Area

Recommendedcutout locationfrom floor 32 1/2”

Allow 1” minimumfor overlap of oven

to and 1 1/4”overlap of ovenbottom of cutout

Allow a minimum of21” for clearance toadjacent corners,drawers, walls, etc.when door is open Cabinet

Width 30”

CL 2” x 4” orequivalentrunnerslevel withbottom ofcutout

SuitableBracing toSupportRunners

21 5/8”Over Centerline

of Cabinet

3 1/2”

6”

12”

CUTOUT OPTIONS FOR SINGLEBUILT-IN OVENS

Skip to Step 3 for Double Built-In Oven models.

There are 4 installation options for single built-in ovens.Choose the appropriate one for your application:

WALL MOUNT—SINGLE BUILT-IN OVEN OPTION

WALL MOUNT—SINGLE BUILT-IN OVEN BELOWAN ADVANTIUM™ OVEN OPTION

WALL MOUNT—SINGLE BUILT-IN OVEN ABOVE A WARMING DRAWER OPTION

UNDER COUNTER—SINGLE BUILT-IN OVENOPTION

D

C

B

A

2


WALL MOUNT—SINGLE BUILT-IN OVENBELOW AN ADVANTIUM OVEN OPTION

• When installed over a single wall oven,allow at least 2” between the two openings.This separation will provide clearance forbottom overlap of the Advantium oven andtop overlap of the single wall oven.

• If you are replacing a GE/Monogram electricdouble oven with the combined installationof an Advantium and single wall oven, themiddle rail separating the two openingsmay need to be larger than the 2” min.shown.

• Always maintain 36 3/4” min. distance fromthe floor to the Advantium oven cutout inany installation combination.

• When installed in combination with aGE/Monogram single wall oven, useseparate electrical junction boxes.

• Refer to Advantium oven installationinstructions for electrical requirements andinstallation details of that product.

• Advantium ovens are approved forinstallation above only certain specifiedwall oven models. See the label attached to the top of the oven for approvedAdvantium oven models.

B WALL MOUNT—SINGLE BUILT-IN OVENABOVE A WARMING DRAWER OPTION

• A 2” min. clearance between oven andwarming drawer cutouts is required.

• Additional clearance may be required if 2 x 4 blocks are used to support the solidfloor of the oven above. Check to be surethat oven supports above the WarmingDrawer location do not obstruct therequired interior depth and height.

• Refer to warming drawer installationinstructions for electrical requirements andinstallation details of that product.

• Warming drawers are approved forinstallation below only certain specifiedwall oven models. See the label attached tothe top of the oven for approved warmingdrawer models.

C

24”Min.

Constructsolid bottommin. 3/8”plywoodsupportedby 2 x 4 or 1x 2 runners,all four sides

30”

2” Min.

Advantiumcutout

Ovencutout

23 1/2” Min.inside

Bottom of warming drawer must be 1”above toekick

2” Min.

Warmingdrawer cutout

Ovencutout

A

Constructsolid bottommin. 3/8”plywood

NOTE: A single wall oven can be installed incombination with the Advantium oven aboveand a warming drawer below as long as thedimensions and information on this page areapplied to the combination installation.

5

6

UNDER COUNTER—SINGLE BUILT-IN OVEN OPTIOND

Top and/or side fillersmay be necessary if unitis positioned betweenexisting cabinets. Besure they are attachedsecurely, since they willanchor the oven in thecabinet.

25”

24”

27 1/4” Min.27 5/16” Max.

3/4”Support Platform

Required

Must Support 225 lbs.

36” TypicalCountertopHeight

5 9/16”Reference dimension formaximum support height withtypical 36” countertop height

NOTE: This oven is not approved to be installed under a cooktop.

Required JunctionBox Area


SINGLE BUILT-IN OVEN CUTOUT OPTIONS (CONT.)

6”

12”

7”3 1/2”

Allow 1” overlaptop of oven and11/16” overlapside edges ofcutout

28 1/2” Min.28 5/8” Max.


7

DOUBLE BUILT-IN OVEN CUTOUT

CUTOUT FOR DOUBLE BUILT-INOVEN

Cabinet Width 30”

Recommended Cutout Location from Floor 12”

Cutout Depth 23 1/2” Min.

Cutout Width 28 1/2” Min.28 5/8” Max.

Cutout Height 51 13/16” Min.51 15/16” Max.

NOTE: If the cabinet does not have a frontframe and the sides are less than 3/4” thick,shim both sides equally to establish thecutout width.

3 CUTOUT FOR DOUBLE BUILT-INOVEN (CONT.)

If the cabinet does not have a solid bottom,two braces or runners must be installed levelwith the bottom of the cutout to support theweight of the oven. For double ovens, therunners and braces must support 375 lbs.

The solid bottom or runners must be levelwith the bottom of the cutout or the bottomtrim may not install correctly and theninterfere with the door opening.

3

7” from side cutout

21”

Cutout Width28 1/2” Min28 5/8” Max.

All cornersmust be cutsquare

Allow11/16” foroverlap ofoven overside edgesof cutout

Cutout Height51 13/16” Min.51 15/16” Max.

RequiredJunctionBox Area

Allow 1”minimum for

overlap of oven top and 1 1/4” overlap

of oven bottomof cutout

Allow aminimum of 21” forclearance to adjacentcorners,drawers,walls, etc.when dooris open

Cabinet Width 30”

CL 2” x 4” orequivalentrunnerslevel withbottom ofcutout

SuitableBracing toSupportRunners

21 5/8”Over Centerline

of Cabinet

Openingbetweeninsidewalls mustbe at Least 28 1/2”Wide

Recommendedcutout locationfrom floor 12”

7”

25”

ON DOUBLE WALL OVENMODELS, REMOVE THE LOWERDOOR ONLY (CONT.):

Close door to the door removal position,which is halfway between the broil stopposition and fully closed.

Lift door up and out until the hinge armis clear of the slot.

E

D

4

88


REMOVE THE LOWER OVEN DOOR ON DOUBLE WALL OVEN MODELS ONLY

ON DOUBLE WALL OVENMODELS, REMOVE THE LOWERDOOR ONLY:

Fully open the door.

Pull the hinge locks down toward thedoor frame, to the unlocked position. A tool, such as a small flat-bladescrewdriver, may be required.

Firmly grasp both sides of the door atthe top.

C

B

A

4

To prevent damage to the door and toprevent excessivemicrowave exposure,do NOT remove the door on thesingle wall oven or the upper ovendoor on the double wall oven.

NOTE: The oven door is heavy. You may needhelp lifting the door high enough to slide itinto the hinge slots. Do not lift the door bythe handle.

Hinge lock

Slot

Pull hinge locks down to unlock

Removal position


99

ELECTRICAL CONNECTIONS


This appliance must be supplied with theproper voltage and frequency, and connectedto an individual, properly grounded branchcircuit, protected by a circuit breaker or fusehaving amperage as noted on rating plate.(Rating Plate is located on oven frame.)

We recommend you have the electrical wiringand hookup of your oven connected by aqualified electrician. After installation, havethe electrician show you where your mainoven disconnect is located.

Check with your local utilities for electricalcodes which apply in your area. Failure towire your oven according to governing codescould result in a hazardous condition. If thereare no local codes, your oven must be wiredand fused to meet the requirements of theNational Electrical Code, ANSI/NFPA No. 70 – Latest Edition. You can get a copy bywriting:

National Fire Protection AssociationBatterymarch ParkQuincy, MA 02269

Effective January 1, 1996, the NationalElectrical Code requires that new, but notexisting, construction utilize a four-conductorconnection to an electric oven. Wheninstalling an electric oven in newconstruction, a mobile home, recreationalvehicle or an area where local codes prohibitgrounding through the neutral conductor,follow the instructions in the section on NEWCONSTRUCTION AND FOUR-CONDUCTORBRANCH CIRCUIT CONNECTION.

You must use a three-wire, single-phase A.C. 208Y/120 Volt or 240/120 Volt, 60 hertzelectrical system. If you connect to aluminumwiring, properly installed connectorsapproved for use with aluminum wiring must be used.

ATTENTION INSTALLER

All electric wall ovens must be hard wired(direct wired) into an approved junction box.A plug and receptacle is NOT permitted onthese products.

DO NOT shorten the flexible conduit. Theconduit strain relief clamp must be securelyattached to the junction box and the flexibleconduit must be securely attached to theclamp. If the flexible conduit will not fit withinthe clamp, do not install the oven until aclamp of the proper size is obtained.

NOTE TO ELECTRICIAN: The 3 power leads supplied with this appliance are ULrecognized for connection to heavier gaugehousehold wiring. The insulation of these 3leads is rated at temperatures much higherthan the temperature rating of householdwiring. The current carrying capacity of theconductor is governed by the wire gauge andthe temperature rating of the insulationaround the wire.

WARNING: Improper connectionof aluminum house wiring to copper leadscan result in an electrical hazard or fire. Useonly connectors designed for joining copperto aluminum and follow the manufacturer’srecommended procedure closely.

Rating plate location

10


ELECTRICAL CONNECTIONS (CONT.)

CONNECT CONDUIT

With the oven supported on a table orplatform in front of the cabinet opening,connect the flexible conduit to the electricaljunction box as shown below. Position theconduit in such a manner that it will liebehind the oven in a natural loop when theoven is installed. You will need to purchasean appropriate strain relief clamp to completethe connection of the conduit to the junction box.

6

NEW CONSTRUCTION ANDFOUR-CONDUCTOR BRANCHCIRCUIT CONNECTION

• When installing in new construction, or• When installing in a mobile home, or• When installing in a recreational vehicle, or• When local codes do not permit grounding

through neutral:Cut the neutral (white) lead from thecrimp. Re-strip the neutral (white) lead toexpose the proper length of conductor.

Attach the appliance grounding lead(green or bare copper) in accordancewith local codes. If the residencegrounding conductor is aluminum, seeWARNING under ATTENTIONINSTALLER.

Connect the oven neutral (white) lead tothe branch circuit neutral (white or gray)in accordance with local codes, using awire nut.

Connect the oven red lead to the branchcircuit red lead and the oven black leadto the branch circuit black lead inaccordance with local codes, using wirenuts. If the residence red, black or whiteleads are aluminum conductors, seeWARNING under ATTENTIONINSTALLER.

Install Junction Box Cover.E

D

C

B

A

7

Conduit

Junction Box Location

Strain Relief Clamp(not included) must beused at Junction Box

Place oven on asupport to assist inconnecting conduit

Red

White

Black

BareGround

Ground Wire

Junction Box Cover

GroundWire

TURN OFF ELECTRICITY

Turn off the circuit breaker or remove fuses tothe oven branch circuit.

5

11


THREE-CONDUCTOR BRANCHCIRCUIT CONNECTION

When connecting to a three-conductor branchcircuit, if local codes permit:

Connect the bare oven ground conductorwith the crimped neutral (white) lead tothe branch circuit neutral (white or grayin color), using a wire nut.

Connect the oven red lead to the branchcircuit red lead in accordance with localcodes, using a wire nut.

Connect the oven black lead to thebranch circuit black lead in accordancewith local codes, using a wire nut. If theresidence red, black or white leads arealuminum conductors, see WARNING under ATTENTION INSTALLER.

Install Junction Box Cover.D

C

B

A

8

Ground andNeutral Wires

Junction Box Cover

12


SECURE THE OVEN IN THE OPENING

SLIDE THE OVEN INTO THEOPENING

Loop (do not tie) the correct length ofstring around the conduit before theoven is slid into place. This will keep theconduit from falling improperly behindthe oven. For the single wall oven, locatestring toward the middle at the bottomof the oven. For the double wall oven,locate string toward the right side at thebottom of the oven.

On a single wall oven, lift the oven intocabinet cutout using the bottom of theoven and the bottom of the door as agrip. Carefully push against the frontedges of the door. On a double walloven, lift the oven into cabinet cutoutusing the lower oven opening as a grip.Carefully push against oven front frame.Do not push against outside edges.

As you slide the oven back, pull thestring so that the conduit will lie behindthe oven in a natural loop.

Once the oven is in the cutout, place thelevel on an oven rack inside the oven tomake sure the oven is level from front toback and from side to side. Use shims asrequired.

NOTE: If marks, blemishes or the cutoutopening are visible above the installed oven,it may be necessary to add wood shimsunder the runners and front trim until themarks or opening are covered.

Once the oven is level and all the way in the opening, remove the string by pullingon one end of the loop.

D

C

B

A

9 DRILL THE PILOT HOLES ANDMOUNT THE OVEN

NOTE: Before drilling the pilot holes, makesure the oven is pushed as far back into theopening as it will go, is level and is centered.

Drill six 1/8” pilot holes through themounting holes (top and bottom) of theside trim, for the #8 screws provided.Drill ten holes for the Double Oven.

WARNING: Mounting screws mustbe used. Failure to do so could result in theoven falling out of the cabinet causingserious injury.

Secure the oven to cabinet with screwsprovided.

NOTE: If the cabinet is particle board, youmust use #8 x 3/4” particle board screws.These may be purchased at any hardwarestore.

B

A

10

Pull out onstring loopwhile pushingthe oven intothe cabinet

MountingHole

Locations

The screws mustbe a minimum of1/4” from the frontof the cutout. (Doornot show in thisview.)

13


To install a single metal bottom trim assembly (on some models), see Step 11.To install a metal bottom trim with a plastic bottom trim (on some models), see Steps 11 and 12.

INSTALL THE METAL BOTTOM TRIM

With oven installed, take the bottom trimand center it on the bottom front edge ofthe cabinet opening.

Using the trim as a template, mark thecenter of each slot (two total) where themounting holes will be drilled.

Remove the trim.

Drill pilot holes into the center of eachtemplate mark.

Place the bottom metal trim over the pre-drilled mounting holes, making sureit is centered.

Using trim screws provided, secure thebottom trim to the bottom edge of thecabinet. If a plastic bottom trim issupplied, proceed to Step 12.

IMPORTANT: If this unit is ever removed fromthe cabinet or the oven is ever pulled out forservice, the trim must be removed first ordamage to the trim will occur.

F

E

D

C

B

A

11 INSTALL THE PLASTIC BOTTOMTRIM (ON SOME MODELS)

Make sure flat side is up on the plasticbottom trim.

Find the key slot on the back of the trim.

Match the key slot with the rivet on thebottom of the side trim, and lower thetrim onto the rivet.

Push the trim down, at both ends, until itsnaps securely into place.

CAUTION: Be sure you do not tipthe oven forward during installation or youmay bend the bottom trim. The bottom trimprovides an opening for cooling air to enterthe cabinet. This opening should never beblocked.

D

C

B

A

12

Single Wall Oven – Door may not be removed.

Double Wall Oven – Lower oven door only may be

removed.

Side Trim

Side Trim

Metal Lower Trim

Trim Screws

Key Hole Slot and Wide Flange at Top

Lower Trim Mounting Rivet onEnd of Metal Lower Trim

Push Trim Down at Both EndsUntil it Snaps Securely Into Place

Side Trim

Side Trim

Metal Lower Trim

Trim Screws

14


REPLACE THE LOWER OVEN DOOR ON DOUBLE WALL OVEN MODELS

ON DOUBLE WALL OVENMODELS, REPLACE THE LOWERDOOR:

Firmly grasp both sides of the door atthe top.

With the door at the same angle as theremoval position, seat the indentation of the hinge arm into the bottom edge ofthe hinge slot. The notch in the hingearm must be fully seated into the bottomof the slot.

Fully open the door. If the door will notfully open, the indentation is not seatedcorrectly in the bottom edge of the slot.

Push the hinge locks up against the frontframe of the oven cavity, to the lockedposition.

Close the oven door.E

D

C

B

A

13

Bottomedge of slot

Hinge arm

Indentation

Hinge lock

Hinge arm

Push hinge locks up to lock

15


FINAL CHECKLISTS

PRE-TEST CHECKLIST

Remove all protective film.

Check to be sure that all wiring is secure and not pinched or in contactwith moving parts.

Check that the bottom trim is installedproperly (see Steps 11 and 12).

Check to be sure the mounting screwsare installed and flush with the side trim(see Steps 9 and 10).

D

C

B

A

14 OPERATION CHECKLIST

Remove all items from the inside of theoven.

Check that conduit is securely connectedto the junction box.

Turn on the power to the oven. (Refer to your Owner’s Manual.) Verify that thebake and broil functions make the ovenhot. Verify by feeling heat coming off theelements within 20 seconds.

See your Owner’s Manual fortroubleshooting list.

NOTE TO ELECTRICIAN:

The power leads supplied with this applianceare UL recognized for connections to largergauge household wiring. The insulation ofthese leads is rated at temperatures muchhigher than the temperature rating ofhousehold wiring. The current carryingcapacity of a conductor is governed by thewire gauge and also the temperature ratingof the insulation around the wire.

NOTE: ALUMINUM WIRING

WARNING: IMPROPERCONNECTION OF ALUMINUM HOUSEWIRING TO THE COPPER LEADS CANRESULT IN AN ELECTRICAL HAZARD OR FIRE.

Splice copper wires to aluminum wiringusing special connectors designed andUL approved for joining copper toaluminum, and follow the manufacturer’srecommended connector procedureclosely.

NOTE: Wire used, location and enclosureof splices, etc., must conform to goodwiring practice and local codes.

B

A

D

C

B

A

15

16Printed in the United States

Documents

Installation 30” Built-In Trivection Instructions...hsei nst ru c ons c m plet ly an dcar efu ly. IMP OR TA NT-Sav et he s in tru tin fo rl o c in sp e t ’su se. IM P TA NT-OBS