Upload
kaizer-soze
View
133
Download
1
Tags:
Embed Size (px)
Citation preview
ROI-S06445-051E 070727
P ASOLINK
N ETWORK
M ANAGEMENT
T ERMINAL
PNMT (Java version)Installation Manual
(WindowsXP)
NEC CorporationCopyright © 2007
ROI-S06445
- i -
Table of Contents
1. Installation Sequence ............................................................................................................................ 1
2. Phone and Modem Options Setting (Standard 19.2Kbps Connection) ............................................ 2
3. Installation of USB Com Port Driver (USB Connection)................................................................... 7
4. Dial-up Setting ..................................................................................................................................... 10
5. SNMP Service Setting ........................................................................................................................... 20
6. PNMT Setup .......................................................................................................................................... 25
7. Launching PNMT ................................................................................................................................. 30
ROI-S06445
- 1 -
1. Installation Sequence
Only Administrator group privilege level users are authorized to configure the following settings,
Standard 19200bps Modem Setting
(Phone and Modem Options Setting)
USB Modem Setting
(Installation of USB Com Port Driver)
Network Element (NE) other than
PASOLINK NEO PASOLINK NEO ONLY
Step 2: Dial-up Connection Setting
Step 3: SNMP Service Setting
Step 4: Pasolink Network Management Terminal (PNMT) Setup
Step 5: Launching PNMT
Step 1: Modem Setting
ROI-S06445
- 2 -
2. Phone and Modem Options Setting (Standard 19.2Kbps Connection)
This section deals with the use of a Standard 19.2Kbps Modem Dial-up connection. (for non-PASOLINK-NEO network elements). If you wish to use a USB Modem Driver (for PASOLINK-NEO network elements, please refer to 3.”Installation of USB Com Port Driver”, p.7
(1) Click Start | Settings | Control Panel.
(2) Click the Phone and Modem Options icon in the Control Panel window to start configuring the modem.
ROI-S06445
- 3 -
(3) Enter your country and area code in the Location Information window. Click [OK].
(4) Verify the Location and Area Code.
ROI-S06445
- 4 -
(5) Select the Modem tab. Click [Add] to continue with adding the new modem for the PNMT.
(6) Check Don’t detect my modem ... and click [Next] to continue.
ROI-S06445
- 5 -
(7) Select Standard Modem Types from the list of Manufacturers and Standard 19200bps Modem from the Models. Click [Next] to continue.
(8) Select Selected ports and COM#, then click [Next] to continue.
ROI-S06445
- 6 -
(9) Click [Finish] to complete the new modem installation.
(10) Verify that Standard 19200 bps Modem and COM1 are displayed. Click [OK].
(11) Please proceed directly to section 4. Dial-up Setting.
ROI-S06445
- 7 -
3. Installation of USB Com Port Driver (USB Connection)
This section describes the installation of a USB Modem Driver (for PASOLINK-NEO network elements) as the dial-up connection.
Connect the PNMT computer to the LCT Port of the NE with a standard USB cable.
(1) Select No, not this time and Click [Next].
(2) Select Install from a list or specific location [Advanced] and click on [Next].
ROI-S06445
- 8 -
(3) Insert the USB driver CD-ROM in the computer’s disk drive and select Search for the best driver in these locations and check Search removable media [floppy, CD-ROM ...] then, click [Next].
(4) Click [Continue Anyway] in the Hardware Installation pop-up alert.
ROI-S06445
- 9 -
(5) USB Modem Driver Installation starts.
(6) USB Com Port Driver installation is complete.
ROI-S06445
- 10 -
4. Dial-up Setting
(1) Click Start | Settings | Control Panel and the Network Connections icon to start configuring
the Dialup setting.
(2) The Network Connections window appears. Click Create a new connection in the Network Tasks area.
ROI-S06445
- 11 -
(3) The Welcome to the New Connection Wizard window appears. Click [Next].
(4) Select Connect to the network at my workplace and click [Next] to continue.
ROI-S06445
- 12 -
(5) Select Dial-up connection and click [Next] to continue.
(6) Select Modem – USB Modem Driver [COM#] and click [Next] to continue.
NOTE
This screen appears only when a USB Modem Driver has been installed.
ROI-S06445
- 13 -
(7) In the New Connection Wizard window, enter Pnmt in the Company Name field and click [Next] to continue.
(8) Enter any number in the Phone number field and click [Next] to continue.
ROI-S06445
- 14 -
(9) Verify that Pnmt is displayed as the connection. You can also create a shortcut on your desktop if desired. Click [Finish].
(10) In the Connect Dial-up Connection window, click [Cancel] to continue. Click Properties in the Connect Dial-up Connection window.
ROI-S06445
- 15 -
(11) Verify that Modem-Standard 19200 bps Modem [COM1] is displayed on the General tab in the Dial-up Connection Properties window. Click [Configure].
(12) In the Modem Configuration window, uncheck all five checkboxes.
ROI-S06445
- 16 -
(13) Retain the default setting on the Options tab and click the Security tab.
(14) Retain the default setting on the Security tab and click the Networking tab.
ROI-S06445
- 17 -
(15) On the Networking tab, verify that PPP ... is`displayed in the Type of dial-up server I am calling field and uncheck File and Printer ... and Client for Microsoft....
(16) Click Settings Uncheck all the boxes in the window that appears, as shown below. Click [OK] to go back to the previous window. Highlight Internet Protocol (TCP/IP) and then click [Properties].
ROI-S06445
- 18 -
(17) Verify that both Obtain an IP address automatically and Obtain DNS server address automatically are selected.
(18) In the Advanced TCP/IP Settings window, uncheck Use IP header compression for the PPP link. Click [OK].
ROI-S06445
- 19 -
(19) Retain the default setting on the Advanced tab and click [OK].
After activating Windows XP SP2 Before activating Windows XP SP2
ROI-S06445
- 20 -
5. SNMP Service Setting
NOTE
It is necessary to remove SNMP Service or to stop it if it has already been installed.
To Remove SNMP Service:
(1) Select Start Setting Control Panel, then, in the Add or Remove Programs window, click Add/Remove Windows Components.
(2) The Windows Components Wizard window appears. Remove the check from Management and Monitoring Tools, and then click Details ...
ROI-S06445
- 21 -
(3) The Management and Monitoring Tools window appears. Confirm that Simple Network Management Protocol is not checked and click [OK]. Return to above window and click [Next].
(4) Click [Finish] to complete the removal of SNMP Service.
ROI-S06445
- 22 -
To Stop SNMP Service: (5) To stop SNMP Service without removing it, click Administrative Tools in the Control Panel
window.
(6) Click Services in the Administrative Tools window.
ROI-S06445
- 23 -
(7) Confirm that SNMP Service is installed and it has started automatically. Select Action Properties on the menu bar in the Services window, or right-click SNMP Service and then click Properties in the SNMP Service pop-up menu.
(8) Select Manual in the Startup type field and click Stop in the Service status field on the General tab. Click [OK] or [Apply].
ROI-S06445
- 24 -
(9) Confirm that the Status of both SNMP Service and SNMP Trap Service is stopped, and that the startup condition for each one is Manual.
(10) Restart the computer.
ROI-S06445
- 25 -
6. PNMT Setup
NOTE
If PNMT software has already been installed, please uninstall it before you install a new version.
(1) Insert the PNMT Installation CDROM.Open the CDROM folder and double-click install.exe.
(2) The following window appears until loading is completed.
ROI-S06445
- 26 -
(3) Introduction window appears. Click [Next].
(4) Specify the directory in which the PNMT is to be installed. Click [Next].
Restore Default Folder: Click this button to choose the license key folder
Choose: Click this button to select another directory
NOTE
The default path is C:\PNMSj. It is not possible to include blank spaces as in “Program Files”. (C denotes the directory where the currently running OS is installed)
ROI-S06445
- 27 -
(5) Specify the License Key file if one is available. Click [Next].
Restore Default Folder: Click this button to revert to default path
Choose: Click this button to choose the license key file
NOTE
If no license key file is available, operation in trial mode is possible.
IMPORTANT: IMMEDIATE IMPORT OF LICENSE
You may use the PNMT on a trial basis for 30 days. After that the PNMT can ONLY be used IF the license has been imported (activated). To obtain the license please contact NEC.
ROI-S06445
- 28 -
(6) Click [Install].
(7) During installation, this window appears.
ROI-S06445
- 29 -
(8) Click [Done] to close the PNMT installation wizard.|
ROI-S06445
- 30 -
7. Launching PNMT
(1) Click Start | Programs |PNMTj |PNMT to start the application.
(2) If he following window appears, select [Unblock] (when using the Windows XP SP2 Firewall).
ROI-S06445
- 31 -
(3) Enter User name and Password, and Select the Connection Entry.
After installation of the PNMT, the initial password will be:-
User name: admin
Password: (There is no initial password. Just press Enter.
A password can then be set.)
Connection: Select Dial-up and Pnmt entry.
NOTE
If another application is using the SNMP Port, application initialization will not be possible; the application will shut down, and the following message will appear.